Post on 02-Sep-2020
Antenna Guide
Wireless LANBAT Family Antennas
BAT Antenna GuideRelease 02 08/2011
Technical SupportHAC.Support@Belden.com
The naming of copyrighted trademarks in this manual, even when not specially indicated, should not be taken to mean that these names may be considered as free in the sense of the trademark and tradename protection law and hence that they may be freely used by anyone.
© 2011 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction, translation, conversion into any electronic medium or machine scannable form is not permitted, either in whole or in part. An exception is the preparation of a backup copy of the software for your own use. For devices with embedded software, the end-user license agreement on the enclosed CD applies.
The performance features described here are binding only if they have been expressly agreed when the contract was made. This document was produced by Hirschmann Automation and Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right to change the contents of this document without prior notice. Hirschmann can give no guarantee in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network components or the associated operating software. In addition, we refer to the conditions of use specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site (www.beldensolutions.com).
Printed in GermanyHirschmann Automation and Control GmbHStuttgarter Str. 45-5172654 NeckartenzlingenGermanyTel.: +49 1805 141538
02-08/2011 4.8.11
Contents
Contents
Introduction 5
1 Current BAT portfolio 7
1.1 BAT54 family 8
1.2 BAT300 family 9
2 AP / Cable / Antenna assembly 11
3 Antenna Selection Criteria 13
4 Which replaces which? 17
5 Omni-Directional Antennas 19
5.1 Omni-Directional Antenna for 2.4 GHz band 20
5.2 Omnidirectional antenna for 5 GHz band 22
5.3 Omnidirectional Antenna for 2.4 and 5 GHz band 24
5.4 Omni-Directional Dualband Antenna for MiMo 30
5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band 32
6 Sector Antennas 35
6.1 Directional diversity Antenna linear for 2.4 GHz 36
6.2 Directional diversity Antenna linear for 5 GHz 38
6.3 Sectoral MiMo Antenna for 5 GHz 40
7 Directional Antennas 43
7.1 Directional Antenna for 2.4 GHz with 14 dBi gain 44
7.2 Directional Antenna linear for 5 GHz band 46
7.3 Narrow Beam directional Antenna for Usage with 802.11n 50
8 Radiating Cable Antennas (Leaky Cable) 53
8.1 Leaky Cable for 2.4 GHz; black 54
BAT Antenna GuideRelease 02 08/2011 3
Contents
9 Cables/Adapter 59
10 Output power calculation 67
11 Fresnel Zone 69
A Statement about passive antennas in hazardous environment 71
B Index 73
C Further Support 75
4BAT Antenna Guide
Release 02 08/2011
Introduction
Introduction
Since 2004 Hirschmann Automation and Control GmbH has offered a steadily increasing product portfolio of wireless LAN devices. This is comprised not only of industrial-grade active devices such as Access Points and Clients. Cables, antennas, lightning protection and so on also form an integral part of the range. Together these components offer the customer the possibility to deploy simple and secure wireless installations. This product portfolio is of course subject to a continuous improvement process. Particularly because WLAN technology is still an innovative field. As a result, the portfolio can experience short term changes.
To improve our product range particulary in respect to resistance to vibration, grounding properties, sealing and radio coverage we decided to update our antenna portfolio. The radio coverage of the new antennas is considerable more
homogeneous, and in live operation leads to a manifestly better result. The scope of delivery now consists of a complete solution, including
antenna, 1 meter cable, and pigtail. This enables problem-free connection to the BAT-F and BAT-Rail.
Vibration-resistant, waterproof, and stable mounting kit is also included. All antennas comply with the IP65 protection class. Also, the connection of cables to lightning protection devices has been
simplified, because all antennas are now equipped with N connectors.
BAT Antenna GuideRelease 02 08/2011 5
Introduction
6BAT Antenna Guide
Release 02 08/2011
Current BAT portfolio
1 Current BAT portfolio
BAT Antenna GuideRelease 02 08/2011 7
Current BAT portfolio 1.1 BAT54 family
1.1 BAT54 family
These products support WLAN standards IEEE 802.11a/b/g/h, and operate at up to 108 Mbps (raw data rate).
BAT-Rail BAT-F BAT-F X2The devices are supplied in metal enclosures for mounting on DIN rails in automation or vehicle applications.
The devices are supplied in IP65/67 metal housings. They are designed for field-level applications or harsh industrial environments.
The devices are supplied with stainless steel covers. They are designed for hazardous environments and are approved for ATEX zone 2.
BAT54-Rail– Industrial WLAN access
point for installation on DIN rails
– Two IEEE 802.11a/b/g/h/i compliant WLAN interfaces
– 2 x LAN/PoE, 2 x 24 V, 1 x 12 V power supply
BAT54-Rail Client– Industrial WLAN access
client for installation on DIN rails
– One IEEE 802.11a/b/g/h/i compliant WLAN interface
– 1 x LAN/PoE, 2 x 24 V, 1 x 12 V power supply
BAT54-F– Industrial WLAN access
point with IP65/67 enclosure
– Two IEEE 802.11a/b/g/h/i compliant WLAN interfaces
– 1 x LAN/PoE, 2 x 24 V power supply
BAT54-F Client– Industrial WLAN access
client with IP65/6 enclosure
– One IEEE 802.11a/b/g/h/i compliant WLAN interface
– 1 x LAN/PoE, 2 x 24 V power supply
BAT54-F Single– Industrial WLAN access
point with IP65/67 enclosure
– One IEEE 802.11a/b/g/h/i compliant WLAN interface, two PoE LAN interfaces
– 2 x LAN/PoE power supply
BAT54-F X2– Industrial WLAN access
point with IP65/67 enclosure
– Two IEEE 802.11a/b/g/h/i compliant WLAN interfaces
– 1 x LAN/PoE, 2 x 24 V power supply
Hirschmann states that BAT antennas can be used in ATEX Zone II in operation with the certified BAT54-F X2 and BAT300-F X2.
Table 1: BAT54 family data and facts
8BAT Antenna Guide
Release 02 08/2011
Current BAT portfolio 1.2 BAT300 family
1.2 BAT300 family
These devices support WLAN standards IEEE 802.11a/b/g/h and 802.11n, and they operate at up to 300 Mbps (raw data rate).
BAT-Rail BAT-F BAT-F X2The devices are supplied in metal enclosures for mounting on DIN rails in automation or vehicle applications.
The devices are supplied in IP65/67 metal housings. They are designed for field-level applications or harsh industrial environments.
The devices are supplied with stainless steel covers. They are designed for hazardous environments and are approved for ATEX zone 2.
BAT300-Rail– Industrial WLAN access
point for installation on DIN rails
– One IEEE 802.11a/b/g/h/n/i compliant WLAN interface
– 2 x LAN/PoE, 2 x 24 V, 1 x 12 V power supply
BAT300-F– Industrial WLAN access
point with IP65/67 enclosure
– One IEEE 802.11a/b/g/h/n/i compliant WLAN interface
– 1 x LAN/PoE, 2 x 24 V power supply
BAT300-F X2– Industrial WLAN access
point with IP65/67 enclosure
– One IEEE 802.11a/b/g/h/n/i compliant WLAN interface
– 1 x LAN/PoE, 2 x 24 V power supply
Table 2: BAT300 family data and facts
BAT Antenna GuideRelease 02 08/2011 9
Current BAT portfolio 1.2 BAT300 family
10BAT Antenna Guide
Release 02 08/2011
AP / Cable / Antenna assembly
2 AP / Cable / Antenna assembly
Since all antenna kits are equipped with 1 m (3.28 ft) cable and pigtail, both AP types BAT-F or BAT-Rail can be connected to the antennas.The BAT Protector can be directly screwed on BAT-F or placed in between two cables since it is equipped with male to female connectors.
Access Point PigtailOptional Protector
Linear antenna
Dual Slantantenna
MiMo antenna
f-m f-m f-m
m-f
OptionalCable
2 m, 5 m, 15 m6.56. ft, 16.4 ft, 49.2 ft
Cable1 m
3.28 ft
BAT Antenna GuideRelease 02 08/2011 11
AP / Cable / Antenna assembly
12BAT Antenna Guide
Release 02 08/2011
Antenna Selection Criteria
3 Antenna Selection Criteria
Art.-No Antenna Description BAT-Rail
BAT-F BAT54 BAT300
943 981-002
BAT-ANT-N-6G-IP65
Omnidirectional antenna for 2.4 GHz band
+++ +++ +++ +
943 981-003
BAT-ANT-N-5A-IP65
Omnidirectional antenna for 5 GHz band
+++ +++ +++ +
942 047-001
BAT-ANT-N-3AGN-F
Omnidirectional antenna for 2.4-and 5 GHz-Band
+
942 046-001
BAT-ANT-RSMA-2AGN-R
Omnidirectional antenna for 2.4-and 5 GHz-Band
+ + +
943 981-004
BAT-ANT-N-6ABG-IP65
Hemispherical antenna for 2.4 and 5 GHz band
+++ +++ +++ +
943 981-005
BAT-ANT-N-14G-IP23
Directional antenna for 2.4 GHz with 14 dBi gain
+++ +++ +++ +
943 981-006
BAT-ANT-N-18A-V-IP65
Directional antenna for 5 GHz band
+++ +++ +++ +
Table 3: +++ Very good; ++ Good; + Possible; - Not usable; nr not relevant
BAT Antenna GuideRelease 02 08/2011 13
Antenna Selection Criteria
943 981-007
BAT-ANT-N-23A-V-IP65
Directional high gain antenna, 23 dBi for 5 GHz band
+++ +++ +++ -
943 981-008
BAT-ANT-N-23A-VH-IP65
Narrow beam directional antenna for usage with 802.11n
+++ +++ + +++
943 981-009
BAT-ANT-N-8G-DS-IP65
Directional diversity antenna linear for 2.4 GHz
+++ +++ +++ ++
943 981-010
BAT-ANT-N-9A-DS-IP65
Directional diversity antenna linear for 5 GHz
+++ +++ +++ ++
943 981-001
BAT-ANT-N-LC-G-50m-IP65
Leaky cable for 2.4 GHz; black
+++ +++ +++ -
943 981-101
BAT-ANT-N-LC-G-100m-IP65
Leaky cable for 2.4 GHz; black
+++ +++ +++ -
943 981-012
BAT-ANT-N-MiMoDB-5N-IP65
Directional diversity Antenna linear for 2.4 GHz
+++ +++ - +++
943 981-013
BAT-ANT-N-MiMo5-9N-IP65
5 GHz MiMo Antenna for sectoral Illumination
+++ +++ - +++
943 903-373
BAT-ANT-Protector m-f
Overvoltage Protector
+++ +++ +++ +++
943 903-374
BAT-LAN-Protector IP68
Surge Arrestor LAN/PoE
+++ +++ +++ +++
943 903-360
BAT-Pigtail
Adapter cable (N female/RP-SMA-Plug)
+++ - nr nr
943 903-514
BAT-CLB-2 N m-f
Antenna Cable N-plug to N-jack2 m (6.56 ft)
+++ +++ +++ +++
Art.-No Antenna Description BAT-Rail
BAT-F BAT54 BAT300
Table 3: +++ Very good; ++ Good; + Possible; - Not usable; nr not relevant
14BAT Antenna Guide
Release 02 08/2011
Antenna Selection Criteria
In the following antenna descriptions you will find suggestions for the distance. These suggestions assist you in the initial consideration of an antenna. The actual distance depends on several factors such as output power, line of sight and interference. The antenna calculator (see on page 67 “Output power calculation”) helps you to calculate the distance.
Note: Hirschmann recommends that you perform a formal site survey to prepare for the installation of a WLAN.
Meaning of the distance declaration: Frequency range: 2.4 GHz
– short distance: up to 200 m, 656 ft with omnidirectional antennas.– medium distance: up to 1 km, 0.6 miles with sector antennas.– long distance: up to 5 km, 3.1miles with directional antennas.
Frequency range: 5 GHz– short distance: up to 300 m, 984 ft with omnidirectional antennas.– medium distance: up to 3 km, 1.8 miles with sector antennas.– long distance: up to 15 km, 9.3 miles with directional antennas.
943 903-516
BAT-CLB-5 N m-f
Antenna Cable N-plug to N-jack5 m (16.40 ft)
+++ +++ +++ +++
943 903-515
BAT-CLB-15 N m-f
Antenna Cable N-plug to N-jack15 m (49.21 ft)
+++ +++ +++ +++
Art.-No Antenna Description BAT-Rail
BAT-F BAT54 BAT300
Table 3: +++ Very good; ++ Good; + Possible; - Not usable; nr not relevant
BAT Antenna GuideRelease 02 08/2011 15
Antenna Selection Criteria
16BAT Antenna Guide
Release 02 08/2011
Which replaces which?
4 Which replaces which?
Former CurrentArt.-No Antenna Art.-No Antenna Description943 903-401 BAT-ANT-N-8G 943 981-002 BAT-ANT-N-6G-IP65 Omnidirectional
antenna for 2.4 GHz band
943 903-301 BAT-ANT-N-8A 943 981-003 BAT-ANT-N-5A-IP65 Omnidirectional antenna for 5 GHz band
943 903-421 BAT-ANT-N-6ABG 943 981-004 BAT-ANT-N-6ABG-IP65
Hemispherical antenna for 2.4 and 5 GHz band
943 903-380 BAT-ANT-N-14G 943 981-005 BAT-ANT-N-14G-IP23
Directional antenna for 2.4 GHz with 14 dBi gain
943 903-320 BAT-ANT-N-12A 943 981-006 BAT-ANT-N-18A-V-IP65
Directional antenna for 5 GHz band
943 903-340 BAT-ANT-N-23/9A 943 981-007 BAT-ANT-N-23A-V-IP65
Directional high gain antenna, 23 dBi for 5 GHz band
943 981-008 BAT-ANT-N-23A-VH-IP65
Narrow beam directional antenna for usage with 802.11n
943 903-411 BAT-TNC-B-D-085-02 943 981-009 BAT-ANT-N-8G-DS-IP65
Directional diversity antenna linear for 2.4 GHz
943 056-111 BAT-TNC-B-D-085-01 943 981-009 BAT-ANT-N-8G-DS-IP65
Directional diversity antenna linear for 2.4 GHz
943 903-310 BAT-ANT-TNC-8b/g DS
943 981-009 BAT-ANT-N-8G-DS-IP65
Directional diversity antenna linear for 2.4 GHz
943 903-330 BAT-ANT-TNC-10A DS
943 981-010 BAT-ANT-N-9A-DS-IP65
Directional diversity antenna linear for 5 GHz
943 981-012 BAT-ANT-N-MiMoDB-5N-IP65
Directional diversity Antenna linear for 2.4 GHz
943 981-013 BAT-ANT-N-MiMo5-9N-IP65
5 GHz MiMo Antenna for sectoral Illumination
BAT Antenna GuideRelease 02 08/2011 17
Which replaces which?
943 903-372 BAT-Surge Arrestor m-f
943 903-373 BAT-ANT-Protector m-f
Overvoltage Protector
943 903-374 BAT-LAN-Protector IP68
Surge Arrestor LAN/PoE
943 903-360 BAT-Pigtail 943 903-360 BAT-Pigtail Adapter cable R-SMA to N-jack
943 903-350 BAT-CLB-7-N 943 903-514 BAT-CLB-2 N m-f Antenna cable N-plug to N-jack
943 903-516 BAT-CLB-5 N m-f Antenna cable N-plug to N-jack
943 903-515 BAT-CLB-15 N m-f Antenna cable N-plug to N-jack
Former CurrentArt.-No Antenna Art.-No Antenna Description
18BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas
5 Omni-Directional Antennas
BAT Antenna GuideRelease 02 08/2011 19
Omni-Directional Antennas 5.1 Omni-Directional Antenna for 2.4 GHz band
5.1 Omni-Directional Antenna for 2.4 GHz band
BAT-ANT-N-6G-IP65Order Number: 943 981-002
To be placed in the middle of the illuminated area. Indoor and outdoor use is possible.
Radiation Patternhorizontal vertical
Frequency range 2400 MHz - 2500 MHzGain 6.0 dBiVSWR (voltage standing wave ratio) < 1.8Polarization Linear, verticalHPBW (half power bandwidth) horizontal 360°Downtilt 0°Max. Power 25 WImpedance 50 ΩConnector N female
Table 4: Electrical Specification
20BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas 5.1 Omni-Directional Antenna for 2.4 GHz band
Temperature – 40 °C to +80 °C, – 40 °F to 176 °FRadome color Grey-whiteRadome material Fiber glassWeight 0.34 kg, 0.75 lbDimensions ø 22 mm x 250 mm, ø 0.87 in x 9.84 inProtection class IP65
Table 5: Environmental & Mechanical Characteristics
1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N femaleMounting material
Table 6: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 21
Omni-Directional Antennas 5.2 Omnidirectional antenna for 5 GHz band
5.2 Omnidirectional antenna for 5 GHz band
BAT-ANT-N-5A-IP65Order Number: 943 981-003
To be placed in the middle of the illuminated area. Indoor and outdoor use is possible.
Radiation Patternhorizontal 5470 MHz vertical 5470 MHz
Frequency range 5150 MHz - 5875 MHzGain 5 dBi VSWR (voltage standing wave ratio) 1.5Polarization Linear, verticalHPBW (half power bandwidth) horizontal 360°HPBW (half power bandwidth) vertical 25°Max. Power 6 W Impedance 50 ΩConnector N female
Table 7: Electrical Specification
22BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas 5.2 Omnidirectional antenna for 5 GHz band
Temperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome color Grey-whiteRadome material PolypropyleneWeight 0.3 kg, 0.66 lbDimensions 16 mm x 160 mm, 0.63 in x 6.3 inProtection class IP65
Table 8: Environmental & Mechanical Characteristics
1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N femaleMounting material
Table 9: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 23
Omni-Directional Antennas 5.3 Omnidirectional Antenna for 2.4 and 5 GHz band
5.3 Omnidirectional Antenna for 2.4 and 5 GHz band
BAT-ANT-N-3AGN-FOrder Number: 942 047-001 (10 pcs.)The antenna is included in the delivery of all BAT-F-devices.
The antenna is directly screwed on the BAT.
24BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas 5.3 Omnidirectional Antenna for 2.4 and 5 GHz band
Radiation Patternhorizontal 2400 MHz horizontal 5000 MHz
vertical 2400 MHz vertical 5000 MHz
Frequency range 2400 MHz - 2500 MHz 5150 MHz - 5875 MHzGain 2.5 dBi 5.0 dBiVSWR (voltage standing wave ratio)
2.0
Polarization Linear, vertical
HPBW (half power bandwidth) horizontal 360°
HPBW (half power bandwidth) vertical 30° vertical 15°Max. Power 2 W
Impedance 50 Ω
Connector N-type male
Table 10: Electrical Specification
BAT Antenna GuideRelease 02 08/2011 25
Omni-Directional Antennas 5.3 Omnidirectional Antenna for 2.4 and 5 GHz band
Temperature -40 °C to +70 °CRadome color Grey-whiteRadome material ABSWeight 70 g (0.15 lb)Dimensions 22 mm x 183 mm (0.87 in x 7.20 in)Protection class IP65
Table 11: Environmental & Mechanical Characteristics
26BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas 5.3 Omnidirectional Antenna for 2.4 and 5 GHz band
BAT-ANT-RSMA-2AGN-ROrder Number: 942 046-001 (10 pcs.)The antenna is included in the delivery of all BAT-Rail-devices.
The antenna is directly screwed on the BAT.
BAT Antenna GuideRelease 02 08/2011 27
Omni-Directional Antennas 5.3 Omnidirectional Antenna for 2.4 and 5 GHz band
Radiation Patternhorizontal 2450 MHz vertical 2450 MHz
horizontal 5250 MHz vertical 5250 MHz
horizontal 5750 MHz vertical 5750 MHz
28BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas 5.3 Omnidirectional Antenna for 2.4 and 5 GHz band
Frequency range 2400 MHz 5250 MHz and 5750 MHzGain 3 dBi 5 dBi VSWR (voltage standing wave ratio)
2.0
Polarization Linear, vertical
HPBW (half power bandwidth) horizontal 360°
HPBW (half power bandwidth) vertical 30° vertical 15°Impedance 50 Ω
Connector Reverse-SMA male
Table 12: Electrical Specification
Temperature −20 °C to +65 °C, −4 °F to +149 °FRadome color BlackRadome material PC/PUWeight 26 g (0.06 lb)Dimensions 21 mm × 160 mm (0.83 in × 6.3 in)
Table 13: Environmental & Mechanical Characteristics
BAT Antenna GuideRelease 02 08/2011 29
Omni-Directional Antennas 5.4 Omni-Directional Dualband Antenna for MiMo
5.4 Omni-Directional Dualband Antenna for MiMo
BAT-ANT-N-MiMoDB-5N-IP65Order Number: 943 981-012
To be placed in the middle of the illuminated area. Indoor and outdoor use is possible.To be used with BAT300 devices for optimal support of MiMo function.
Radiation Pattern5 GHz 24 GHzhorizontal vertical horizontal vertical
30BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas 5.4 Omni-Directional Dualband Antenna for MiMo
Frequency range 2400-2500 / 5150-5875 MHzGain 3.5 dBi / 5.5 dBi VSWR (voltage standing wave ratio) 1.8Polarization 3x Linear, verticalHPBW (half power bandwidth) horizontal 360°Downtilt 0°Max. Power 2 W Impedance 50 ΩConnector 3 x N male at 1 m (3.28 ft) cable directly
attached
Table 14: Electrical Specification
Temperature – 40 °C to +80 °C, – 40 °F to 176 °FRadome color 7035 (Light Gray)Radome material plasticWeight 0.3 kg, 0.66 lbDimensions 310 mm x 110 mm x 40 mm
12.2 in 4.3 in x 1.6 inProtection class IP65
Table 15: Environmental & Mechanical Characteristics
3 x 90 cm (3 ft) directly mounted to the antenna with N male conectors3 x Pigtail, R-SMA male to N femaleMounting material
Table 16: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 31
Omni-Directional Antennas 5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band
5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band
BAT-ANT-N-6ABG-IP65Order Number: 943 981-004
To be placed on moving parts, vehicles or boxes.
Radiation Patternhorizontal vertical
32BAT Antenna Guide
Release 02 08/2011
Omni-Directional Antennas 5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band
Frequency range 2300 - 2500 and 4900 - 5935 MHzImpedance 50 ΩVSWR (voltage standing wave ratio) 1.8Polarization Linear, verticalGain 6dBi @2.4 GHz, 8dBi @5 GHz3 dB beamwidth horizontal @ 2.4 GHz 360°3 dB beamwidth horizontal @ 5 GHz 173°Max. Power 75 W (CW) at 25 °C, 77 °F
Table 17: Electrical Specification
1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N female
Table 18: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 33
Omni-Directional Antennas 5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band
34BAT Antenna Guide
Release 02 08/2011
Sector Antennas
6 Sector Antennas
BAT Antenna GuideRelease 02 08/2011 35
Sector Antennas 6.1 Directional diversity Antenna linear for 2.4 GHz
6.1 Directional diversity Antenna linear for 2.4 GHz
BAT-ANT-N-8G-DS-IP65Order Number: 943 981-009
Suitable for use with BAT300 and for polarization diversity with BAT54.
Radiation Patternhorizontal vertical
36BAT Antenna Guide
Release 02 08/2011
Sector Antennas 6.1 Directional diversity Antenna linear for 2.4 GHz
Frequency range 2400 - 2485 MHz Impedance 50 ΩVSWR (voltage standing wave ratio) 1.5Polarization dual linear, ± 45° slant Gain 8 dBi 3 dB beamwidth horizontal 75° 3 dB beamwidth vertical 70° Downtilt 0°Isolation between ports 25 dB Front to back ratio 14 dB Max. Power 10 W (CW) at 25 °C, 77 °F Connector 2 x N female
Table 19: Electrical Specification
Dimensions 101 mm x 80 mm x 35 mm 3.98 in x 3.15 in x 1.38 in
Weight 0.11 kg , 0.24 lbRadome material LEXAN EXL 9330 Radome color RAL 7044 (silk gray) Operating temperature range – 40 °C to +80 °C, – 40 °F to 176 °FStorage temperature range – 40 °C to +80 °C, – 40 °F to 176 °FWindload 15 N at 160 km/h, 3.37 lbf at 99 m/hProtection class IP65
Table 20: Mechanical Properties
2 x 1 m (3.28 ft) with N male connectors at both ends.2 x Pigtail, R-SMA male to N femaleMounting material
Table 21: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 37
Sector Antennas 6.2 Directional diversity Antenna linear for 5 GHz
6.2 Directional diversity Antenna linear for 5 GHz
BAT-ANT-N-9A-DS-IP65Order Number: 943 981-010
Suitable for use with BAT300 and for polarization diversity with BAT54.
Radiation Patternhorizontal vertical
38BAT Antenna Guide
Release 02 08/2011
Sector Antennas 6.2 Directional diversity Antenna linear for 5 GHz
Frequency range 5150 - 5925 MHz Impedance 50 ΩVSWR (voltage standing wave ratio) 2Polarization dual linear, ± 45° slant Gain 9 dBi 3 dB beamwidth horizontal 70° 3 dB beamwidth vertical 60° Downtilt 0°Isolation between ports 20 dB Front to back ratio 20 dB Max. Power 10 W (CW) at 25 °C, 77 °F Connector 2 x N female
Table 22: Electrical Specification
Dimensions 101 mm x 80 mm x 35 mm 3.98 in x 3.15 in x 1.38 in
Weight 0.11 kg , 0.24 lbHousing material ASA and aluminum Radome material ASA Radome material LEXAN EXL 9330 Radome color RAL 7044 (silk gray) Operating temperature range – 40 °C to +80 °C, – 40 °F to 176 °FStorage temperature range – 40 °C to +80 °C, – 40 °F to 176 °FWindload 15 N at 160 km/h, 3.37 lbf at 99 m/hProtection class IP65
Table 23: Mechanical Properties
2 x 1 m (3.28 ft) with N male connectors at both ends.2 x Pigtail, R-SMA male to N femaleMounting material
Table 24: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 39
Sector Antennas 6.3 Sectoral MiMo Antenna for 5 GHz
6.3 Sectoral MiMo Antenna for 5 GHz
BAT-ANT-N-MiMo5-9N-IP65Order Number: 943 981-013
Radiation Patternhorizontal – Port 1 vertical – Port 1
horizontal – Port 2 vertical – Port 2
40BAT Antenna Guide
Release 02 08/2011
Sector Antennas 6.3 Sectoral MiMo Antenna for 5 GHz
This antenna is intended for applications operating at 5 GHz. The antenna is designed to be placed on flat surfaces or other edges in both indoor or outdoor applications. The antenna is also useful for medium range point to point applications.
horizontal – Port 3 vertical – Port 3
Frequency range 5150 MHz - 5875 MHzImpedance 50 ΩVSWR (voltage standing wave ratio) 1.5Polarization 3 x linear vertical / horizontal / +45°Gain 9 dBi 3 dB beamwidth horizontal 65° 3 dB beamwidth vertical 65° Downtilt 0°Max. Power 2 W (CW) at 25 °C, 77 °F Connector N female
Table 25: Electrical Specification
Dimensions 101 mm x 80 mm x 35 mm 3.98 in x 3.15 in x 1.38 in
Weight 0.11 kg , 0.24 lbRadome material LEXAN EXL 9330 Radome color RAL 7044 (silk gray) Operating temperature range – 40 °C to +80 °C, – 40 °F to 176 °FStorage temperature range – 40 °C to +80 °C, – 40 °F to 176 °FWindload 15 N at 160 km/h, 3.37 lbf at 99 m/hProtection class IP65
Table 26: Mechanical Properties
BAT Antenna GuideRelease 02 08/2011 41
Sector Antennas 6.3 Sectoral MiMo Antenna for 5 GHz
3 x 1m (3.28 ft) with N male connectors at both ends.3 x Pigtail, R-SMA male to N femaleMounting material
Table 27: Cable and Accessories
42BAT Antenna Guide
Release 02 08/2011
Directional Antennas
7 Directional Antennas
BAT Antenna GuideRelease 02 08/2011 43
Directional Antennas 7.1 Directional Antenna for 2.4 GHz with 14 dBi gain
7.1 Directional Antenna for 2.4 GHz with 14 dBi gain
BAT-ANT-N-14G-IP23Order Number: 943 981-005
Radiation Patternhorizontal vertical
Frequency range 2300 - 2500 MHz Impedance 50 ΩVSWR (voltage standing wave ratio) 1.5Polarization verticalGain 14 dBi 3 dB beamwidth horizontal 35° 3 dB beamwidth vertical 30° Downtilt 0°Front to back ratio 20 dB Max. Power 75 W (CW) at 25 °C, 77 °F Connector N female
Table 28: Electrical Specification
44BAT Antenna Guide
Release 02 08/2011
Directional Antennas 7.1 Directional Antenna for 2.4 GHz with 14 dBi gain
Dimensions 101 mm x 80 mm x 35 mm 3.98 in x 3.15 in x 1.38 in
Weight 0.11 kg , 0.24 lbRadome material LEXAN EXL 9330 Radome color RAL 7044 (silk gray) Operating temperature range – 40 °C to +80 °C, – 40 °F to 176 °FStorage temperature range – 40 °C to +80 °C, – 40 °F to 176 °FWindload 15 N at 160 km/h, 3.37 lbf at 99 m/hProtection class IP23
Table 29: Mechanical Properties
1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N femaleMounting material
Table 30: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 45
Directional Antennas 7.2 Directional Antenna linear for 5 GHz band
7.2 Directional Antenna linear for 5 GHz band
BAT-ANT-N-18A-V-IP65Order Number: 943 981-006
This antenna is intended for applications operating at 5 GHz over medium distances (see distance description on page 15).Indoor and outdoor use is possible.
Radiation Patternhorizontal vertical
Frequency range 5150 MHz - 5250 MHz5250 MHz - 5350 MHz5350 MHz - 5725 MHz5725 MHz - 5875 MHz
Gain 18 dBi19 dBi18.5 dBi18 dBi
Polarization Linear, verticalHPBW / horizontal 18°HPBW / vertical 18°Front to back ratio > 30 dBPower handling 6 W (CW)Impedance 50 ΩConnector N Jack
Table 31: Electrical Specification
46BAT Antenna Guide
Release 02 08/2011
Directional Antennas 7.2 Directional Antenna linear for 5 GHz band
Windload @ wind speed 104 N at 216 km/h, 23.4 lbf at 64 m/hTemperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome material plasticRadome color 7035 (Light Gray)Weight 0.11 kg, 0.24 lbDimensions 190 mm x 190 mm x 30.5 mm
7.48 in x 7.48 in x 1.2 inProtection class IP65 / IP67
Table 32: Environmental & Mechanical Characteristics
1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N femaleMounting material
Table 33: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 47
Directional Antennas 7.2 Directional Antenna linear for 5 GHz band
BAT-ANT-N-23A-V-IP65Order Number: 943 981-007
This antenna is intended for applications operating at 5 GHz over long distances (see distance description on page 15).Suggested for BAT54 devices exclusively.Relevant for North America:Operate the antennas BAT-ANT-N-23A-V-IP65 and BAT-ANT-N-23A-VH-IP65 exclusively in point-to-point connections.
Radiation Patternhorizontal vertical
Frequency range 5.150 - 5.350 MHz / 5.470 - 5.875 MHzGain 23 dBi VSWR (voltage standing wave ratio) < 1.5Polarization Linear, verticalHPBW / horizontal 9°HPBW / vertical 9°Front to back ratio > 30 dBMax. Power 6WImpedance 50 ΩConnector N Jack
Table 34: Electrical Specification
48BAT Antenna Guide
Release 02 08/2011
Directional Antennas 7.2 Directional Antenna linear for 5 GHz band
Windload @ survival speed 264N at 220 km/h, 59.3 lbf at 136 m/hTemperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome material plasticRadome color Grey-whiteWeight 1.5 kg, 3.31 lbDimensions 305 mm x 305 mm x 25 mm (12 in x 12 in x 1 in)Protection class IP65 / IP67
Table 35: Environmental & Mechanical Characteristics
1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N femaleMounting material for wall and mast mount
Table 36: Cable and Accessories
BAT Antenna GuideRelease 02 08/2011 49
Directional Antennas 7.3 Narrow Beam directional Antenna for Usage with 802.11n
7.3 Narrow Beam directional Antenna for Usage with 802.11n
BAT-ANT-N-23A-VH-IP65Order Number: 943 981-008
Relevant for North America:Operate the antennas BAT-ANT-N-23A-V-IP65 and BAT-ANT-N-23A-VH-IP65 exclusively in point-to-point connections.
50BAT Antenna Guide
Release 02 08/2011
Directional Antennas 7.3 Narrow Beam directional Antenna for Usage with 802.11n
This antenna is intended for applications operating at 5 GHz over long distances (see distance description on page 15).Suggested for BAT300 devices.MiMo is achieved via polarization diversity.
Radiation Patternport horizontal / plane horizontal port vertical / plane horizontal
port horizontal / plane vertical port vertical / plane vertical
Frequency range 5150 MHz - 5875 MHzGain 23 dBi VSWR (voltage standing wave ratio) < 1.7Polarization dual Linear, vertical and horizontalHPBW / horizontal 9°HPBW / vertical 9°Front to back ratio -30 dBMax. Power 6WImpedance 50 ΩConnector 2 x N female
Table 37: Electrical Specification
BAT Antenna GuideRelease 02 08/2011 51
Directional Antennas 7.3 Narrow Beam directional Antenna for Usage with 802.11n
Windload @ survival speed 264N at 220 km/h, 59.3 lbf at 136 m/hTemperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome material plasticRadome color Grey-whiteWeight 2.5 kg, 5.5 lbDimensions 371 mm x 371 mm x 40 mm
14.6 in x 14.6 in x 1.6 inProtection class IP65 / IP67
Table 38: Environmental & Mechanical Characteristics
2 x 1 m (3.28 ft) with N male connectors at both ends.2 x Pigtail, R-SMA male to N femaleMounting material for wall and mast mount
Table 39: Cable and Accessories
52BAT Antenna Guide
Release 02 08/2011
Radiating Cable Antennas (Leaky Cable)
8 Radiating Cable Antennas (Leaky Cable)
BAT Antenna GuideRelease 02 08/2011 53
Radiating Cable Antennas (Leaky Cable)
8.1 Leaky Cable for 2.4 GHz; black
8.1 Leaky Cable for 2.4 GHz; black
Radiating cables are coaxial cables that are equipped with small slots in their shields at regular intervals that operate as antennas. This leads to a homogeneous field around the cable.
The 100 m (328 ft) cable is designed to be fed by 2 access points, each feeding the cable for approximately 50 m (164 ft). The 50 m (164 ft) cable is designed to be used with one Access Point and equipped with a terminator at the end.
100 m; 328 ft 50 m; 164 ft
54BAT Antenna Guide
Release 02 08/2011
Radiating Cable Antennas (Leaky Cable)
8.1 Leaky Cable for 2.4 GHz; black
BAT-ANT-N-LC-G-50m-IP65Order Number: 943 981-001
Cable length 50 m, 164 ftCable specification 2 x N male connectors; 0.15 dB at 2.4 GHz
Table 40: Specification
Frequency band 2000 MHz - 2900 MHzAntenna connector N-type male
Table 41: Radio technology
Operating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFStorage/transport temperature –70 ºC to +85 ºC, –94 ºF to +185 ºFDimensions 50 m, 164 ft; d = 15 mm, 0.6 inProtection class IP65Weight 12 kg, 26.5 lb
Table 42: Ambient conditions
Halogen free and flame retardant outer sheathLow corrosive gas emission according to IEC 60754-2Flame retardant according to IEC 60332-1 and IEC 60332-3 cat. CLow smoke emission according to IEC 61034
Table 43: Flammability Characteristics
Leaky Cable2 x N-connector preassembled1 x terminator 50 Ohm50 x fastening clip
Table 44: Scope of delivery and accessories
BAT Antenna GuideRelease 02 08/2011 55
Radiating Cable Antennas (Leaky Cable)
8.1 Leaky Cable for 2.4 GHz; black
BAT-ANT-N-LC-G-100m-IP65Order Number: 943 981-101
Cable length 100 m, 328 ftCable specification 2 x N male connectors; 0.15 dB at 2.4 GHz
Table 45: Specification
Frequency band 2000 MHz - 2900 MHzAntenna connector N-type male
Table 46: Radio technology
Operating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFStorage/transport temperature –70 ºC to +85 ºC, –94 ºF to +185 ºFDimensions 100 m, 328 ft; d = 15 mm, 0.6 inProtection class IP65Weight 24 kg, 53 lb
Table 47: Ambient conditions
Halogen free and flame retardant outer sheathLow corrosive gas emission according to IEC 60754-2Flame retardant according to IEC 60332-1 and IEC 60332-3 cat. CLow smoke emission according to IEC 61034
Table 48: Flammability Characteristics
Leaky Cable2 x N-connector preassembled1 x terminator 50 Ohm100 x fastening clip
Table 49: Scope of delivery and accessories
56BAT Antenna Guide
Release 02 08/2011
Radiating Cable Antennas (Leaky Cable)
8.1 Leaky Cable for 2.4 GHz; black
Configurations Longitudinal Attenuation
dB/100 m, db/328 ftLC at 10 cm, 4 in from a concrete floor 15LC at 15 mm, 0.6 in from a metal surface 17LC directly against a metal surface 34
Table 50: Longitudinal attenuation of both cables between 2.4 and 2.485 GHz
BAT Antenna GuideRelease 02 08/2011 57
Radiating Cable Antennas (Leaky Cable)
8.1 Leaky Cable for 2.4 GHz; black
58BAT Antenna Guide
Release 02 08/2011
Cables/Adapter
9 Cables/Adapter
Available as accessories. Note: All antennas are supplied with 1 m, 3.28 ft cable N m-m and Pigtail.
BAT-CLB-2 N m-f, BAT-CLB-2 N f-f
Order Number: m-m: 943 903-513m-f: 943 903-514
Length 2 m, 6.56 ftAttenuation 1.4 dB / 2.4 GHz
3 dB / 5 GHzConnector N male to femaleProtection class IP65
Table 51: Characteristics
Temperature range –40 °C... +85 °C, –40 °F... +185 °FInstallation temperature –20 °C... + 60 °C, –4 °F... + 140 °FFlammability UL 1581 § 1080 (VW-1)Halogen free IEC 607542002/95/EC (RoHS) compliant
Table 52: Flammability Characteristics
BAT Antenna GuideRelease 02 08/2011 59
Cables/Adapter
BAT-CLB-5 N m-fOrder Number: 943 903-516
Length 5 m, 16.4 ftAttenuation 1.3 dB / 2.4 GHz
2.3 dB / 5 GHzConnector N male/ N female
Table 53: Characteristics
Temperature range –40 °C... +85 °C, –40 °F... +185 °FInstallation temperature –20 °C... + 60 °C, –4 °F... + 140 °FFlammability UL 1581 § 1080 (VW-1)Halogen free IEC 607542002/95/EC (RoHS) compliant
Table 54: Flammability Characteristics
60BAT Antenna Guide
Release 02 08/2011
Cables/Adapter
BAT-CLB-15 N m-fOrder Number: 943 903-515
Low loss cable
Length 15 m, 49.2 ftAttenuation 3 dB / 2.4 GHz
4 dB / 5 GHzConnector N male/ N female
Table 55: Characteristics
Temperature range –40 °C... +85 °C, –40 °F... +185 °FInstallation temperature –20 °C... + 60 °C, –4 °F... + 140 °FFlammability UL 1581 § 1080 (VW-1)Halogen free IEC 607542002/95/EC (RoHS) compliant
Table 56: Flammability Characteristics
BAT Antenna GuideRelease 02 08/2011 61
Cables/Adapter
BAT-PigtailOrder Number: 943 903-360
This part is included in antenna kits.
Length 0.2 m, 0.66 ftAttenuation 0.5 dB / 2.4 GHz
1 dB / 5 GHzConnector N female/ RPSMA-Plug
Table 57: Characteristics
62BAT Antenna Guide
Release 02 08/2011
Cables/Adapter
BAT-ANT-Protector m-fOrder Number: 943 903-373
This BAT-ANT-Protector m-f is additionally equipped with a capacitor that also helps avoid damage of electrical static discharge. This device is strongly recommended to be used in- and outdoor wherever electrical discharge, overvoltage or unclear grounding occur.Please refer to the Outdoor Installation Guide for how to mount and plan the installation.
Main path connectors Port 1: unprotected, N plug (male) - Port 2: protected, N jack (female)
Mounting and grounding MH170/brk (MH=bulkhead mounting/brk=bracket)
Side of bulkhead protected sideDesign specialty inline design
Table 58: Product Configuration
Impedance 50 ΩFrequency range 2000 to 6000 MHzReturn loss >= 20 dBInsertion loss <= 0.2 dBRF CW power <= 300 WPIM 3rd order not specifiedSurge current handling capability 50 multiple kA (test pulse 8/20 μs)Residual pulse energy 0.0001 μJ typically (test pulse 4 kV 1.2/50
μs / 2 kA 8/20 μs) Main path - protected side
Table 59: Electrical Specification
Weight 0.085 kg, 0.19 lbOperating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFWaterproof degree IP65 (according to IEC 60529, data refers to
the coupled state)2002/95/EC (RoHS) compliant
Table 60: Environmental & Mechanical Characteristics
BAT Antenna GuideRelease 02 08/2011 63
Cables/Adapter
BAT-LAN-Protector IP68Order Number: 943 903-374
Overvoltage protector for the PoE/LAN cable.IP68 shielded.Cable not included.
Main path connectors RJ45 jack (female) – RJ45 jack (unprotected side – protected side)
Mounting via mounting bracketGrounding via mounting bracket or grounding M6 screw (ring
of cable shoe > 6.5 mm, 0.26 in)
Table 61: Product Configuration
Data transmission rate
1000 Mbit/s
Frequency range DC to 100 MHzImpedance 100 ΩVoltage rating per pair ±6 VCurrent rating per pair 1.5 A max.Response Time 2 nsCurrent handling capability
wire - wirewire - groundshield – ground
0.1 kA (test pulse 8/20 µs)2.5 kA (test pulse 8/20 µs)6 kA (test pulse 8/20 µs)
Protection level wire - wirewire - groundshield – ground
20 V typically (test pulse 4 kV 1.2/50 μs / 2 kA 8/20 µs)700 V typically (test pulse 4 kV 1.2/50 μs / 2 kA 8/20 µs)700 V typically (test pulse 4 kV 1.2/50 μs / 2 kA 8/20 µs)
Clamping voltage wire - wirewire - groundshield – ground
15 V90 V90 V
Table 62: Electrical Specification
Cable category according to ISO/IEC 11801:2002 class D specified (up to CAT-5e system)
Operating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFProtection class IP68Weight 0.33 kg, 0.73 lb
Table 63: Environmental & Mechanical Characteristics
64BAT Antenna Guide
Release 02 08/2011
Cables/Adapter
Please refer to the Outdoor Installation Guide for how to mount and plan the installation.
BAT Antenna GuideRelease 02 08/2011 65
Cables/Adapter
66BAT Antenna Guide
Release 02 08/2011
Output power calculation
10 Output power calculation
Hirschmann has developed its BAT devices to enable easy product configuration. Proper configuration is a three step process:
choose the correct country setting enable or disable DFS if necessary ( e.g. by choosing indoor mode) insert the correct gain of the antenna/cable/protector system
Please refer to the BAT54, BAT300 Configuration and Administration Guide for instructions how to configure BAT devices correctly.
In order to easily calculate the possible range and distance of a WLAN installation, Hirschmann provides the Antenna Distance Calculator.You can find the Antenna Distance Calculator on the supplied CD.Also you can download this Excel tool from www.beldensolutions.com.
BAT Antenna GuideRelease 02 08/2011 67
Output power calculation
68BAT Antenna Guide
Release 02 08/2011
Fresnel Zone
11 Fresnel Zone
The Hirschmann Antenna Distance Calculator is based on the following calculation scheme:The 1st Fresnel zone has the form of an ellipsoid of rotation whereby the antennas are located in the focal points of the ellipsoid.This zone is calculated by the shaft section b of the ellipsoidb = 0.5*√ (λ*d)
d stands for the distance between the antennas (km)λ = wavelength of electromagnetic wave λ = c / fc is the speed of the wave, nearly like vacuum approx. 300,000 km/s; 186,411 miles/sf = frequency of the wave in 1/s = Hz.
Fresnel Zone
BAT Antenna GuideRelease 02 08/2011 69
Fresnel Zone
At distance above 2 km (1.24 miles), it is necessary to add earth curvature to calculate the altitude at which the antenna has to be mounted. Some examples:
d = 2 km, d = 1.24 milesf = 2.4 GHz b = 0.5 * √ (300,000 km/s / 2.4 GHz * 2 km) = 7.9 m
b = 0.5 * √ (186,411 miles/s / 2.4 GHz * 1.24 miles) = 311 inf = 5.8 GHz b = 0.5 * √ (300,000 km/s / 5.8 GHz * 2 km) = 5 m
b = 0.5 * √ (186,411 miles/s / 5.8 GHz * 1.24 miles) = 197 in
Table 64: Examples of Fresnel Zone Calculations
5 km, 3.1 miles
=> 0.50 m, 19.7 in
10 km, 6.2 miles
=> 2.00 m, 78.7 in
70BAT Antenna Guide
Release 02 08/2011
Statement about passive antennas in hazardous environment
A Statement about passive antennas in hazardous environment
Hirschmann BAT antennas are passive devices which are not able to increase the power by themselves.
The BAT54-F X2 and BAT300-F X2 meet the requirements of EN 60 079-15 (IEC 60079-15) (type of protection: Ex nA II T4) independent of the passive accessories used.See KEMA test report No. 2109557, Annex A.1., last clause “Other issues”.
The radiated radio frequency energy is not more than 100 mW (less than 20dBm), which is acceptable for apparatus group IIC (maximum 2W allowed in accordance with TR EN 50427).
Hirschmann states that BAT antennas can be used in ATEX Zone II in operation with the certified BAT54-F X2 and BAT300-F X2.
BAT Antenna GuideRelease 02 08/2011 71
Statement about passive antennas in hazardous environment
72BAT Antenna Guide
Release 02 08/2011
Index
B Index
AATEX Zone II 8, 71Antenna Distance Calculator 67, 69
EEN 60 079-15 71
FFAQ 75Fresnel zone 69
MMessage URL http://www.beldensolutions.com 75, 75Message URL http://www.hicomcenter.com 75, 75
RRadiating cable 54
TTR EN 50427 71, 71Technical questions 75Training courses 75
BAT FamilyRelease 02 08/2011 73
Index
74BAT Family
Release 02 08/2011
Further Support
C Further Support
Technical Questions and Training CoursesIn the event of technical queries, please contact your local Hirschmann distributor or Hirschmann office. You can find the addresses of our distributors on the Internet: www.beldensolutions.com.
Our support line is also at your disposal: Tel. +49 1805 14-1538 Fax +49 7127 14-1551
Answers to Frequently Asked Questions can be found on the Hirschmann internet site (www.beldensolutions.com) at the end of the product sites in the FAQ category. The current training courses to technology and products can be found under http://www.hicomcenter.com.
Hirschmann Competence CenterIn the long term, excellent products alone do not guarantee a successful customer relationship. Only comprehensive service makes a difference worldwide. In the current global competition scenario, the Hirschmann Competence Center is ahead of its competitors on three counts with its complete range of innovative services:
Consulting incorporates comprehensive technical advice, from system evaluation through network planning to project planing.
Training offers you an introduction to the basics, product briefing and user training with certification.
Support ranges from the first installation through the standby service to maintenance concepts.
With the Hirschmann Competence Center, you have decided against making any compromises. Our client-customized package leaves you free to choose the service components you want to use. Internet: http://www.hicomcenter.com.
BAT Antenna GuideRelease 02 08/2011 75