Wireless LAN BAT Family Antennas - Belden...8 Radiating Cable Antennas (Leaky Cable) 53 8.1 Leaky...

Antenna Guide

Wireless LANBAT Family Antennas

BAT Antenna GuideRelease 02 08/2011

Technical [email protected]

The naming of copyrighted trademarks in this manual, even when not specially indicated, should not be taken to mean that these names may be considered as free in the sense of the trademark and tradename protection law and hence that they may be freely used by anyone.

© 2011 Hirschmann Automation and Control GmbH

Manuals and software are protected by copyright. All rights reserved. The copying, reproduction, translation, conversion into any electronic medium or machine scannable form is not permitted, either in whole or in part. An exception is the preparation of a backup copy of the software for your own use. For devices with embedded software, the end-user license agreement on the enclosed CD applies.

The performance features described here are binding only if they have been expressly agreed when the contract was made. This document was produced by Hirschmann Automation and Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right to change the contents of this document without prior notice. Hirschmann can give no guarantee in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network components or the associated operating software. In addition, we refer to the conditions of use specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site (www.beldensolutions.com).

Printed in GermanyHirschmann Automation and Control GmbHStuttgarter Str. 45-5172654 NeckartenzlingenGermanyTel.: +49 1805 141538

02-08/2011 4.8.11

Contents

Contents

Introduction 5

1 Current BAT portfolio 7

1.1 BAT54 family 8

1.2 BAT300 family 9

2 AP / Cable / Antenna assembly 11

3 Antenna Selection Criteria 13

4 Which replaces which? 17

5 Omni-Directional Antennas 19

5.1 Omni-Directional Antenna for 2.4 GHz band 20

5.2 Omnidirectional antenna for 5 GHz band 22

5.3 Omnidirectional Antenna for 2.4 and 5 GHz band 24

5.4 Omni-Directional Dualband Antenna for MiMo 30

5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band 32

6 Sector Antennas 35

6.1 Directional diversity Antenna linear for 2.4 GHz 36

6.2 Directional diversity Antenna linear for 5 GHz 38

6.3 Sectoral MiMo Antenna for 5 GHz 40

7 Directional Antennas 43

7.1 Directional Antenna for 2.4 GHz with 14 dBi gain 44

7.2 Directional Antenna linear for 5 GHz band 46

7.3 Narrow Beam directional Antenna for Usage with 802.11n 50

8 Radiating Cable Antennas (Leaky Cable) 53

8.1 Leaky Cable for 2.4 GHz; black 54

BAT Antenna GuideRelease 02 08/2011 3

Contents

9 Cables/Adapter 59

10 Output power calculation 67

11 Fresnel Zone 69

A Statement about passive antennas in hazardous environment 71

B Index 73

C Further Support 75

4BAT Antenna Guide

Release 02 08/2011

Introduction

Introduction

Since 2004 Hirschmann Automation and Control GmbH has offered a steadily increasing product portfolio of wireless LAN devices. This is comprised not only of industrial-grade active devices such as Access Points and Clients. Cables, antennas, lightning protection and so on also form an integral part of the range. Together these components offer the customer the possibility to deploy simple and secure wireless installations. This product portfolio is of course subject to a continuous improvement process. Particularly because WLAN technology is still an innovative field. As a result, the portfolio can experience short term changes.

To improve our product range particulary in respect to resistance to vibration, grounding properties, sealing and radio coverage we decided to update our antenna portfolio. The radio coverage of the new antennas is considerable more

homogeneous, and in live operation leads to a manifestly better result. The scope of delivery now consists of a complete solution, including

antenna, 1 meter cable, and pigtail. This enables problem-free connection to the BAT-F and BAT-Rail.

Vibration-resistant, waterproof, and stable mounting kit is also included. All antennas comply with the IP65 protection class. Also, the connection of cables to lightning protection devices has been

simplified, because all antennas are now equipped with N connectors.


Introduction

6BAT Antenna Guide

Release 02 08/2011

Current BAT portfolio

1 Current BAT portfolio


Current BAT portfolio 1.1 BAT54 family

1.1 BAT54 family

These products support WLAN standards IEEE 802.11a/b/g/h, and operate at up to 108 Mbps (raw data rate).

BAT-Rail BAT-F BAT-F X2The devices are supplied in metal enclosures for mounting on DIN rails in automation or vehicle applications.

The devices are supplied in IP65/67 metal housings. They are designed for field-level applications or harsh industrial environments.

The devices are supplied with stainless steel covers. They are designed for hazardous environments and are approved for ATEX zone 2.

BAT54-Rail– Industrial WLAN access

point for installation on DIN rails

– Two IEEE 802.11a/b/g/h/i compliant WLAN interfaces

– 2 x LAN/PoE, 2 x 24 V, 1 x 12 V power supply

BAT54-Rail Client– Industrial WLAN access

client for installation on DIN rails

– One IEEE 802.11a/b/g/h/i compliant WLAN interface


BAT54-F– Industrial WLAN access

point with IP65/67 enclosure


– 1 x LAN/PoE, 2 x 24 V power supply

BAT54-F Client– Industrial WLAN access

client with IP65/6 enclosure

– One IEEE 802.11a/b/g/h/i compliant WLAN interface


BAT54-F Single– Industrial WLAN access


– One IEEE 802.11a/b/g/h/i compliant WLAN interface, two PoE LAN interfaces

– 2 x LAN/PoE power supply

BAT54-F X2– Industrial WLAN access




Hirschmann states that BAT antennas can be used in ATEX Zone II in operation with the certified BAT54-F X2 and BAT300-F X2.

Table 1: BAT54 family data and facts

8BAT Antenna Guide

Release 02 08/2011


1.2 BAT300 family

These devices support WLAN standards IEEE 802.11a/b/g/h and 802.11n, and they operate at up to 300 Mbps (raw data rate).

BAT-Rail BAT-F BAT-F X2The devices are supplied in metal enclosures for mounting on DIN rails in automation or vehicle applications.

The devices are supplied in IP65/67 metal housings. They are designed for field-level applications or harsh industrial environments.

The devices are supplied with stainless steel covers. They are designed for hazardous environments and are approved for ATEX zone 2.

BAT300-Rail– Industrial WLAN access

point for installation on DIN rails

– One IEEE 802.11a/b/g/h/n/i compliant WLAN interface


BAT300-F– Industrial WLAN access




BAT300-F X2– Industrial WLAN access




Table 2: BAT300 family data and facts



10BAT Antenna Guide

Release 02 08/2011

AP / Cable / Antenna assembly

2 AP / Cable / Antenna assembly

Since all antenna kits are equipped with 1 m (3.28 ft) cable and pigtail, both AP types BAT-F or BAT-Rail can be connected to the antennas.The BAT Protector can be directly screwed on BAT-F or placed in between two cables since it is equipped with male to female connectors.

Access Point PigtailOptional Protector

Linear antenna

Dual Slantantenna

MiMo antenna

f-m f-m f-m

m-f

OptionalCable

2 m, 5 m, 15 m6.56. ft, 16.4 ft, 49.2 ft

Cable1 m

3.28 ft


AP / Cable / Antenna assembly

12BAT Antenna Guide

Release 02 08/2011

Antenna Selection Criteria

3 Antenna Selection Criteria

Art.-No Antenna Description BAT-Rail

BAT-F BAT54 BAT300

943 981-002

BAT-ANT-N-6G-IP65

Omnidirectional antenna for 2.4 GHz band

+++ +++ +++ +

943 981-003

BAT-ANT-N-5A-IP65

Omnidirectional antenna for 5 GHz band

+++ +++ +++ +

942 047-001

BAT-ANT-N-3AGN-F

Omnidirectional antenna for 2.4-and 5 GHz-Band

+

942 046-001

BAT-ANT-RSMA-2AGN-R

Omnidirectional antenna for 2.4-and 5 GHz-Band

+ + +

943 981-004

BAT-ANT-N-6ABG-IP65

Hemispherical antenna for 2.4 and 5 GHz band

+++ +++ +++ +

943 981-005

BAT-ANT-N-14G-IP23

Directional antenna for 2.4 GHz with 14 dBi gain

+++ +++ +++ +

943 981-006

BAT-ANT-N-18A-V-IP65

Directional antenna for 5 GHz band

+++ +++ +++ +

Table 3: +++ Very good; ++ Good; + Possible; - Not usable; nr not relevant



943 981-007

BAT-ANT-N-23A-V-IP65

Directional high gain antenna, 23 dBi for 5 GHz band

+++ +++ +++ -

943 981-008

BAT-ANT-N-23A-VH-IP65

Narrow beam directional antenna for usage with 802.11n

+++ +++ + +++

943 981-009

BAT-ANT-N-8G-DS-IP65

Directional diversity antenna linear for 2.4 GHz

+++ +++ +++ ++

943 981-010

BAT-ANT-N-9A-DS-IP65

Directional diversity antenna linear for 5 GHz

+++ +++ +++ ++

943 981-001

BAT-ANT-N-LC-G-50m-IP65

Leaky cable for 2.4 GHz; black

+++ +++ +++ -

943 981-101

BAT-ANT-N-LC-G-100m-IP65

Leaky cable for 2.4 GHz; black

+++ +++ +++ -

943 981-012

BAT-ANT-N-MiMoDB-5N-IP65

Directional diversity Antenna linear for 2.4 GHz

+++ +++ - +++

943 981-013

BAT-ANT-N-MiMo5-9N-IP65

5 GHz MiMo Antenna for sectoral Illumination

+++ +++ - +++

943 903-373

BAT-ANT-Protector m-f

Overvoltage Protector

+++ +++ +++ +++

943 903-374

BAT-LAN-Protector IP68

Surge Arrestor LAN/PoE

+++ +++ +++ +++

943 903-360

BAT-Pigtail

Adapter cable (N female/RP-SMA-Plug)

+++ - nr nr

943 903-514

BAT-CLB-2 N m-f

Antenna Cable N-plug to N-jack2 m (6.56 ft)

+++ +++ +++ +++


BAT-F BAT54 BAT300


14BAT Antenna Guide

Release 02 08/2011


In the following antenna descriptions you will find suggestions for the distance. These suggestions assist you in the initial consideration of an antenna. The actual distance depends on several factors such as output power, line of sight and interference. The antenna calculator (see on page 67 “Output power calculation”) helps you to calculate the distance.

Note: Hirschmann recommends that you perform a formal site survey to prepare for the installation of a WLAN.

Meaning of the distance declaration: Frequency range: 2.4 GHz

– short distance: up to 200 m, 656 ft with omnidirectional antennas.– medium distance: up to 1 km, 0.6 miles with sector antennas.– long distance: up to 5 km, 3.1miles with directional antennas.

Frequency range: 5 GHz– short distance: up to 300 m, 984 ft with omnidirectional antennas.– medium distance: up to 3 km, 1.8 miles with sector antennas.– long distance: up to 15 km, 9.3 miles with directional antennas.

943 903-516

BAT-CLB-5 N m-f


+++ +++ +++ +++

943 903-515

BAT-CLB-15 N m-f


+++ +++ +++ +++


BAT-F BAT54 BAT300




16BAT Antenna Guide

Release 02 08/2011

Which replaces which?

4 Which replaces which?

Former CurrentArt.-No Antenna Art.-No Antenna Description943 903-401 BAT-ANT-N-8G 943 981-002 BAT-ANT-N-6G-IP65 Omnidirectional

antenna for 2.4 GHz band

943 903-301 BAT-ANT-N-8A 943 981-003 BAT-ANT-N-5A-IP65 Omnidirectional antenna for 5 GHz band

943 903-421 BAT-ANT-N-6ABG 943 981-004 BAT-ANT-N-6ABG-IP65

Hemispherical antenna for 2.4 and 5 GHz band

943 903-380 BAT-ANT-N-14G 943 981-005 BAT-ANT-N-14G-IP23

Directional antenna for 2.4 GHz with 14 dBi gain

943 903-320 BAT-ANT-N-12A 943 981-006 BAT-ANT-N-18A-V-IP65

Directional antenna for 5 GHz band

943 903-340 BAT-ANT-N-23/9A 943 981-007 BAT-ANT-N-23A-V-IP65

Directional high gain antenna, 23 dBi for 5 GHz band

943 981-008 BAT-ANT-N-23A-VH-IP65

Narrow beam directional antenna for usage with 802.11n

943 903-411 BAT-TNC-B-D-085-02 943 981-009 BAT-ANT-N-8G-DS-IP65


943 056-111 BAT-TNC-B-D-085-01 943 981-009 BAT-ANT-N-8G-DS-IP65


943 903-310 BAT-ANT-TNC-8b/g DS

943 981-009 BAT-ANT-N-8G-DS-IP65


943 903-330 BAT-ANT-TNC-10A DS

943 981-010 BAT-ANT-N-9A-DS-IP65

Directional diversity antenna linear for 5 GHz

943 981-012 BAT-ANT-N-MiMoDB-5N-IP65

Directional diversity Antenna linear for 2.4 GHz

943 981-013 BAT-ANT-N-MiMo5-9N-IP65

5 GHz MiMo Antenna for sectoral Illumination


Which replaces which?

943 903-372 BAT-Surge Arrestor m-f

943 903-373 BAT-ANT-Protector m-f

Overvoltage Protector

943 903-374 BAT-LAN-Protector IP68

Surge Arrestor LAN/PoE

943 903-360 BAT-Pigtail 943 903-360 BAT-Pigtail Adapter cable R-SMA to N-jack

943 903-350 BAT-CLB-7-N 943 903-514 BAT-CLB-2 N m-f Antenna cable N-plug to N-jack

943 903-516 BAT-CLB-5 N m-f Antenna cable N-plug to N-jack

943 903-515 BAT-CLB-15 N m-f Antenna cable N-plug to N-jack

Former CurrentArt.-No Antenna Art.-No Antenna Description

18BAT Antenna Guide

Release 02 08/2011

Omni-Directional Antennas

5 Omni-Directional Antennas


Omni-Directional Antennas 5.1 Omni-Directional Antenna for 2.4 GHz band

5.1 Omni-Directional Antenna for 2.4 GHz band

BAT-ANT-N-6G-IP65Order Number: 943 981-002

To be placed in the middle of the illuminated area. Indoor and outdoor use is possible.

Radiation Patternhorizontal vertical

Frequency range 2400 MHz - 2500 MHzGain 6.0 dBiVSWR (voltage standing wave ratio) < 1.8Polarization Linear, verticalHPBW (half power bandwidth) horizontal 360°Downtilt 0°Max. Power 25 WImpedance 50 ΩConnector N female

Table 4: Electrical Specification

20BAT Antenna Guide

Release 02 08/2011

Omni-Directional Antennas 5.1 Omni-Directional Antenna for 2.4 GHz band

Temperature – 40 °C to +80 °C, – 40 °F to 176 °FRadome color Grey-whiteRadome material Fiber glassWeight 0.34 kg, 0.75 lbDimensions ø 22 mm x 250 mm, ø 0.87 in x 9.84 inProtection class IP65

Table 5: Environmental & Mechanical Characteristics

1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N femaleMounting material

Table 6: Cable and Accessories


Omni-Directional Antennas 5.2 Omnidirectional antenna for 5 GHz band

5.2 Omnidirectional antenna for 5 GHz band

BAT-ANT-N-5A-IP65Order Number: 943 981-003

To be placed in the middle of the illuminated area. Indoor and outdoor use is possible.

Radiation Patternhorizontal 5470 MHz vertical 5470 MHz

Frequency range 5150 MHz - 5875 MHzGain 5 dBi VSWR (voltage standing wave ratio) 1.5Polarization Linear, verticalHPBW (half power bandwidth) horizontal 360°HPBW (half power bandwidth) vertical 25°Max. Power 6 W Impedance 50 ΩConnector N female


22BAT Antenna Guide

Release 02 08/2011

Omni-Directional Antennas 5.2 Omnidirectional antenna for 5 GHz band

Temperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome color Grey-whiteRadome material PolypropyleneWeight 0.3 kg, 0.66 lbDimensions 16 mm x 160 mm, 0.63 in x 6.3 inProtection class IP65





Omni-Directional Antennas 5.3 Omnidirectional Antenna for 2.4 and 5 GHz band

5.3 Omnidirectional Antenna for 2.4 and 5 GHz band

BAT-ANT-N-3AGN-FOrder Number: 942 047-001 (10 pcs.)The antenna is included in the delivery of all BAT-F-devices.

The antenna is directly screwed on the BAT.

24BAT Antenna Guide

Release 02 08/2011


Radiation Patternhorizontal 2400 MHz horizontal 5000 MHz

vertical 2400 MHz vertical 5000 MHz

Frequency range 2400 MHz - 2500 MHz 5150 MHz - 5875 MHzGain 2.5 dBi 5.0 dBiVSWR (voltage standing wave ratio)

2.0

Polarization Linear, vertical

HPBW (half power bandwidth) horizontal 360°

HPBW (half power bandwidth) vertical 30° vertical 15°Max. Power 2 W

Impedance 50 Ω

Connector N-type male




Temperature -40 °C to +70 °CRadome color Grey-whiteRadome material ABSWeight 70 g (0.15 lb)Dimensions 22 mm x 183 mm (0.87 in x 7.20 in)Protection class IP65


26BAT Antenna Guide

Release 02 08/2011


BAT-ANT-RSMA-2AGN-ROrder Number: 942 046-001 (10 pcs.)The antenna is included in the delivery of all BAT-Rail-devices.

The antenna is directly screwed on the BAT.



Radiation Patternhorizontal 2450 MHz vertical 2450 MHz

horizontal 5250 MHz vertical 5250 MHz

horizontal 5750 MHz vertical 5750 MHz

28BAT Antenna Guide

Release 02 08/2011


Frequency range 2400 MHz 5250 MHz and 5750 MHzGain 3 dBi 5 dBi VSWR (voltage standing wave ratio)

2.0

Polarization Linear, vertical

HPBW (half power bandwidth) horizontal 360°

HPBW (half power bandwidth) vertical 30° vertical 15°Impedance 50 Ω

Connector Reverse-SMA male


Temperature −20 °C to +65 °C, −4 °F to +149 °FRadome color BlackRadome material PC/PUWeight 26 g (0.06 lb)Dimensions 21 mm × 160 mm (0.83 in × 6.3 in)



Omni-Directional Antennas 5.4 Omni-Directional Dualband Antenna for MiMo

5.4 Omni-Directional Dualband Antenna for MiMo

BAT-ANT-N-MiMoDB-5N-IP65Order Number: 943 981-012

To be placed in the middle of the illuminated area. Indoor and outdoor use is possible.To be used with BAT300 devices for optimal support of MiMo function.

Radiation Pattern5 GHz 24 GHzhorizontal vertical horizontal vertical

30BAT Antenna Guide

Release 02 08/2011

Omni-Directional Antennas 5.4 Omni-Directional Dualband Antenna for MiMo

Frequency range 2400-2500 / 5150-5875 MHzGain 3.5 dBi / 5.5 dBi VSWR (voltage standing wave ratio) 1.8Polarization 3x Linear, verticalHPBW (half power bandwidth) horizontal 360°Downtilt 0°Max. Power 2 W Impedance 50 ΩConnector 3 x N male at 1 m (3.28 ft) cable directly

attached


Temperature – 40 °C to +80 °C, – 40 °F to 176 °FRadome color 7035 (Light Gray)Radome material plasticWeight 0.3 kg, 0.66 lbDimensions 310 mm x 110 mm x 40 mm

12.2 in 4.3 in x 1.6 inProtection class IP65


3 x 90 cm (3 ft) directly mounted to the antenna with N male conectors3 x Pigtail, R-SMA male to N femaleMounting material



Omni-Directional Antennas 5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band

5.5 Dual band Hemispherical Antenna for 2.4 and 5 GHz band

BAT-ANT-N-6ABG-IP65Order Number: 943 981-004

To be placed on moving parts, vehicles or boxes.


32BAT Antenna Guide

Release 02 08/2011


Frequency range 2300 - 2500 and 4900 - 5935 MHzImpedance 50 ΩVSWR (voltage standing wave ratio) 1.8Polarization Linear, verticalGain 6dBi @2.4 GHz, 8dBi @5 GHz3 dB beamwidth horizontal @ 2.4 GHz 360°3 dB beamwidth horizontal @ 5 GHz 173°Max. Power 75 W (CW) at 25 °C, 77 °F


1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N female




34BAT Antenna Guide

Release 02 08/2011

Sector Antennas

6 Sector Antennas


Sector Antennas 6.1 Directional diversity Antenna linear for 2.4 GHz

6.1 Directional diversity Antenna linear for 2.4 GHz

BAT-ANT-N-8G-DS-IP65Order Number: 943 981-009

Suitable for use with BAT300 and for polarization diversity with BAT54.


36BAT Antenna Guide

Release 02 08/2011

Sector Antennas 6.1 Directional diversity Antenna linear for 2.4 GHz

Frequency range 2400 - 2485 MHz Impedance 50 ΩVSWR (voltage standing wave ratio) 1.5Polarization dual linear, ± 45° slant Gain 8 dBi 3 dB beamwidth horizontal 75° 3 dB beamwidth vertical 70° Downtilt 0°Isolation between ports 25 dB Front to back ratio 14 dB Max. Power 10 W (CW) at 25 °C, 77 °F Connector 2 x N female


Dimensions 101 mm x 80 mm x 35 mm 3.98 in x 3.15 in x 1.38 in

Weight 0.11 kg , 0.24 lbRadome material LEXAN EXL 9330 Radome color RAL 7044 (silk gray) Operating temperature range – 40 °C to +80 °C, – 40 °F to 176 °FStorage temperature range – 40 °C to +80 °C, – 40 °F to 176 °FWindload 15 N at 160 km/h, 3.37 lbf at 99 m/hProtection class IP65

Table 20: Mechanical Properties

2 x 1 m (3.28 ft) with N male connectors at both ends.2 x Pigtail, R-SMA male to N femaleMounting material



Sector Antennas 6.2 Directional diversity Antenna linear for 5 GHz

6.2 Directional diversity Antenna linear for 5 GHz

BAT-ANT-N-9A-DS-IP65Order Number: 943 981-010

Suitable for use with BAT300 and for polarization diversity with BAT54.


38BAT Antenna Guide

Release 02 08/2011

Sector Antennas 6.2 Directional diversity Antenna linear for 5 GHz

Frequency range 5150 - 5925 MHz Impedance 50 ΩVSWR (voltage standing wave ratio) 2Polarization dual linear, ± 45° slant Gain 9 dBi 3 dB beamwidth horizontal 70° 3 dB beamwidth vertical 60° Downtilt 0°Isolation between ports 20 dB Front to back ratio 20 dB Max. Power 10 W (CW) at 25 °C, 77 °F Connector 2 x N female



Weight 0.11 kg , 0.24 lbHousing material ASA and aluminum Radome material ASA Radome material LEXAN EXL 9330 Radome color RAL 7044 (silk gray) Operating temperature range – 40 °C to +80 °C, – 40 °F to 176 °FStorage temperature range – 40 °C to +80 °C, – 40 °F to 176 °FWindload 15 N at 160 km/h, 3.37 lbf at 99 m/hProtection class IP65


2 x 1 m (3.28 ft) with N male connectors at both ends.2 x Pigtail, R-SMA male to N femaleMounting material



Sector Antennas 6.3 Sectoral MiMo Antenna for 5 GHz

6.3 Sectoral MiMo Antenna for 5 GHz

BAT-ANT-N-MiMo5-9N-IP65Order Number: 943 981-013

Radiation Patternhorizontal – Port 1 vertical – Port 1

horizontal – Port 2 vertical – Port 2

40BAT Antenna Guide

Release 02 08/2011


This antenna is intended for applications operating at 5 GHz. The antenna is designed to be placed on flat surfaces or other edges in both indoor or outdoor applications. The antenna is also useful for medium range point to point applications.

horizontal – Port 3 vertical – Port 3

Frequency range 5150 MHz - 5875 MHzImpedance 50 ΩVSWR (voltage standing wave ratio) 1.5Polarization 3 x linear vertical / horizontal / +45°Gain 9 dBi 3 dB beamwidth horizontal 65° 3 dB beamwidth vertical 65° Downtilt 0°Max. Power 2 W (CW) at 25 °C, 77 °F Connector N female







3 x 1m (3.28 ft) with N male connectors at both ends.3 x Pigtail, R-SMA male to N femaleMounting material


42BAT Antenna Guide

Release 02 08/2011

Directional Antennas

7 Directional Antennas


Directional Antennas 7.1 Directional Antenna for 2.4 GHz with 14 dBi gain

7.1 Directional Antenna for 2.4 GHz with 14 dBi gain

BAT-ANT-N-14G-IP23Order Number: 943 981-005


Frequency range 2300 - 2500 MHz Impedance 50 ΩVSWR (voltage standing wave ratio) 1.5Polarization verticalGain 14 dBi 3 dB beamwidth horizontal 35° 3 dB beamwidth vertical 30° Downtilt 0°Front to back ratio 20 dB Max. Power 75 W (CW) at 25 °C, 77 °F Connector N female


44BAT Antenna Guide

Release 02 08/2011

Directional Antennas 7.1 Directional Antenna for 2.4 GHz with 14 dBi gain







Directional Antennas 7.2 Directional Antenna linear for 5 GHz band

7.2 Directional Antenna linear for 5 GHz band

BAT-ANT-N-18A-V-IP65Order Number: 943 981-006

This antenna is intended for applications operating at 5 GHz over medium distances (see distance description on page 15).Indoor and outdoor use is possible.


Frequency range 5150 MHz - 5250 MHz5250 MHz - 5350 MHz5350 MHz - 5725 MHz5725 MHz - 5875 MHz

Gain 18 dBi19 dBi18.5 dBi18 dBi

Polarization Linear, verticalHPBW / horizontal 18°HPBW / vertical 18°Front to back ratio > 30 dBPower handling 6 W (CW)Impedance 50 ΩConnector N Jack


46BAT Antenna Guide

Release 02 08/2011


Windload @ wind speed 104 N at 216 km/h, 23.4 lbf at 64 m/hTemperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome material plasticRadome color 7035 (Light Gray)Weight 0.11 kg, 0.24 lbDimensions 190 mm x 190 mm x 30.5 mm

7.48 in x 7.48 in x 1.2 inProtection class IP65 / IP67






BAT-ANT-N-23A-V-IP65Order Number: 943 981-007

This antenna is intended for applications operating at 5 GHz over long distances (see distance description on page 15).Suggested for BAT54 devices exclusively.Relevant for North America:Operate the antennas BAT-ANT-N-23A-V-IP65 and BAT-ANT-N-23A-VH-IP65 exclusively in point-to-point connections.


Frequency range 5.150 - 5.350 MHz / 5.470 - 5.875 MHzGain 23 dBi VSWR (voltage standing wave ratio) < 1.5Polarization Linear, verticalHPBW / horizontal 9°HPBW / vertical 9°Front to back ratio > 30 dBMax. Power 6WImpedance 50 ΩConnector N Jack


48BAT Antenna Guide

Release 02 08/2011


Windload @ survival speed 264N at 220 km/h, 59.3 lbf at 136 m/hTemperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome material plasticRadome color Grey-whiteWeight 1.5 kg, 3.31 lbDimensions 305 mm x 305 mm x 25 mm (12 in x 12 in x 1 in)Protection class IP65 / IP67


1 m, 3.28 ft with N male connectors at both ends.Pigtail, R-SMA male to N femaleMounting material for wall and mast mount



Directional Antennas 7.3 Narrow Beam directional Antenna for Usage with 802.11n

7.3 Narrow Beam directional Antenna for Usage with 802.11n

BAT-ANT-N-23A-VH-IP65Order Number: 943 981-008

Relevant for North America:Operate the antennas BAT-ANT-N-23A-V-IP65 and BAT-ANT-N-23A-VH-IP65 exclusively in point-to-point connections.

50BAT Antenna Guide

Release 02 08/2011


This antenna is intended for applications operating at 5 GHz over long distances (see distance description on page 15).Suggested for BAT300 devices.MiMo is achieved via polarization diversity.

Radiation Patternport horizontal / plane horizontal port vertical / plane horizontal

port horizontal / plane vertical port vertical / plane vertical

Frequency range 5150 MHz - 5875 MHzGain 23 dBi VSWR (voltage standing wave ratio) < 1.7Polarization dual Linear, vertical and horizontalHPBW / horizontal 9°HPBW / vertical 9°Front to back ratio -30 dBMax. Power 6WImpedance 50 ΩConnector 2 x N female




Windload @ survival speed 264N at 220 km/h, 59.3 lbf at 136 m/hTemperature – 45 °C to +70 °C, – 49 °F to +158 °FRadome material plasticRadome color Grey-whiteWeight 2.5 kg, 5.5 lbDimensions 371 mm x 371 mm x 40 mm

14.6 in x 14.6 in x 1.6 inProtection class IP65 / IP67


2 x 1 m (3.28 ft) with N male connectors at both ends.2 x Pigtail, R-SMA male to N femaleMounting material for wall and mast mount


52BAT Antenna Guide

Release 02 08/2011

Radiating Cable Antennas (Leaky Cable)

8 Radiating Cable Antennas (Leaky Cable)



8.1 Leaky Cable for 2.4 GHz; black


Radiating cables are coaxial cables that are equipped with small slots in their shields at regular intervals that operate as antennas. This leads to a homogeneous field around the cable.

The 100 m (328 ft) cable is designed to be fed by 2 access points, each feeding the cable for approximately 50 m (164 ft). The 50 m (164 ft) cable is designed to be used with one Access Point and equipped with a terminator at the end.

100 m; 328 ft 50 m; 164 ft

54BAT Antenna Guide

Release 02 08/2011



BAT-ANT-N-LC-G-50m-IP65Order Number: 943 981-001

Cable length 50 m, 164 ftCable specification 2 x N male connectors; 0.15 dB at 2.4 GHz

Table 40: Specification

Frequency band 2000 MHz - 2900 MHzAntenna connector N-type male

Table 41: Radio technology

Operating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFStorage/transport temperature –70 ºC to +85 ºC, –94 ºF to +185 ºFDimensions 50 m, 164 ft; d = 15 mm, 0.6 inProtection class IP65Weight 12 kg, 26.5 lb

Table 42: Ambient conditions

Halogen free and flame retardant outer sheathLow corrosive gas emission according to IEC 60754-2Flame retardant according to IEC 60332-1 and IEC 60332-3 cat. CLow smoke emission according to IEC 61034

Table 43: Flammability Characteristics

Leaky Cable2 x N-connector preassembled1 x terminator 50 Ohm50 x fastening clip

Table 44: Scope of delivery and accessories




BAT-ANT-N-LC-G-100m-IP65Order Number: 943 981-101

Cable length 100 m, 328 ftCable specification 2 x N male connectors; 0.15 dB at 2.4 GHz

Table 45: Specification

Frequency band 2000 MHz - 2900 MHzAntenna connector N-type male

Table 46: Radio technology

Operating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFStorage/transport temperature –70 ºC to +85 ºC, –94 ºF to +185 ºFDimensions 100 m, 328 ft; d = 15 mm, 0.6 inProtection class IP65Weight 24 kg, 53 lb

Table 47: Ambient conditions

Halogen free and flame retardant outer sheathLow corrosive gas emission according to IEC 60754-2Flame retardant according to IEC 60332-1 and IEC 60332-3 cat. CLow smoke emission according to IEC 61034


Leaky Cable2 x N-connector preassembled1 x terminator 50 Ohm100 x fastening clip

Table 49: Scope of delivery and accessories

56BAT Antenna Guide

Release 02 08/2011



Configurations Longitudinal Attenuation

dB/100 m, db/328 ftLC at 10 cm, 4 in from a concrete floor 15LC at 15 mm, 0.6 in from a metal surface 17LC directly against a metal surface 34

Table 50: Longitudinal attenuation of both cables between 2.4 and 2.485 GHz




58BAT Antenna Guide

Release 02 08/2011

Cables/Adapter

9 Cables/Adapter

Available as accessories. Note: All antennas are supplied with 1 m, 3.28 ft cable N m-m and Pigtail.

BAT-CLB-2 N m-f, BAT-CLB-2 N f-f

Order Number: m-m: 943 903-513m-f: 943 903-514

Length 2 m, 6.56 ftAttenuation 1.4 dB / 2.4 GHz

3 dB / 5 GHzConnector N male to femaleProtection class IP65

Table 51: Characteristics

Temperature range –40 °C... +85 °C, –40 °F... +185 °FInstallation temperature –20 °C... + 60 °C, –4 °F... + 140 °FFlammability UL 1581 § 1080 (VW-1)Halogen free IEC 607542002/95/EC (RoHS) compliant



Cables/Adapter

BAT-CLB-5 N m-fOrder Number: 943 903-516

Length 5 m, 16.4 ftAttenuation 1.3 dB / 2.4 GHz

2.3 dB / 5 GHzConnector N male/ N female




60BAT Antenna Guide

Release 02 08/2011

Cables/Adapter

BAT-CLB-15 N m-fOrder Number: 943 903-515

Low loss cable

Length 15 m, 49.2 ftAttenuation 3 dB / 2.4 GHz

4 dB / 5 GHzConnector N male/ N female





Cables/Adapter

BAT-PigtailOrder Number: 943 903-360

This part is included in antenna kits.

Length 0.2 m, 0.66 ftAttenuation 0.5 dB / 2.4 GHz

1 dB / 5 GHzConnector N female/ RPSMA-Plug


62BAT Antenna Guide

Release 02 08/2011

Cables/Adapter

BAT-ANT-Protector m-fOrder Number: 943 903-373

This BAT-ANT-Protector m-f is additionally equipped with a capacitor that also helps avoid damage of electrical static discharge. This device is strongly recommended to be used in- and outdoor wherever electrical discharge, overvoltage or unclear grounding occur.Please refer to the Outdoor Installation Guide for how to mount and plan the installation.

Main path connectors Port 1: unprotected, N plug (male) - Port 2: protected, N jack (female)

Mounting and grounding MH170/brk (MH=bulkhead mounting/brk=bracket)

Side of bulkhead protected sideDesign specialty inline design

Table 58: Product Configuration

Impedance 50 ΩFrequency range 2000 to 6000 MHzReturn loss >= 20 dBInsertion loss <= 0.2 dBRF CW power <= 300 WPIM 3rd order not specifiedSurge current handling capability 50 multiple kA (test pulse 8/20 μs)Residual pulse energy 0.0001 μJ typically (test pulse 4 kV 1.2/50

μs / 2 kA 8/20 μs) Main path - protected side


Weight 0.085 kg, 0.19 lbOperating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFWaterproof degree IP65 (according to IEC 60529, data refers to

the coupled state)2002/95/EC (RoHS) compliant



Cables/Adapter

BAT-LAN-Protector IP68Order Number: 943 903-374

Overvoltage protector for the PoE/LAN cable.IP68 shielded.Cable not included.

Main path connectors RJ45 jack (female) – RJ45 jack (unprotected side – protected side)

Mounting via mounting bracketGrounding via mounting bracket or grounding M6 screw (ring

of cable shoe > 6.5 mm, 0.26 in)

Table 61: Product Configuration

Data transmission rate

1000 Mbit/s

Frequency range DC to 100 MHzImpedance 100 ΩVoltage rating per pair ±6 VCurrent rating per pair 1.5 A max.Response Time 2 nsCurrent handling capability

wire - wirewire - groundshield – ground

0.1 kA (test pulse 8/20 µs)2.5 kA (test pulse 8/20 µs)6 kA (test pulse 8/20 µs)

Protection level wire - wirewire - groundshield – ground

20 V typically (test pulse 4 kV 1.2/50 μs / 2 kA 8/20 µs)700 V typically (test pulse 4 kV 1.2/50 μs / 2 kA 8/20 µs)700 V typically (test pulse 4 kV 1.2/50 μs / 2 kA 8/20 µs)

Clamping voltage wire - wirewire - groundshield – ground

15 V90 V90 V


Cable category according to ISO/IEC 11801:2002 class D specified (up to CAT-5e system)

Operating temperature –40 ºC to +85 ºC, –40 ºF to +185 ºFProtection class IP68Weight 0.33 kg, 0.73 lb


64BAT Antenna Guide

Release 02 08/2011

Cables/Adapter

Please refer to the Outdoor Installation Guide for how to mount and plan the installation.


Cables/Adapter

66BAT Antenna Guide

Release 02 08/2011

Output power calculation

10 Output power calculation

Hirschmann has developed its BAT devices to enable easy product configuration. Proper configuration is a three step process:

choose the correct country setting enable or disable DFS if necessary ( e.g. by choosing indoor mode) insert the correct gain of the antenna/cable/protector system

Please refer to the BAT54, BAT300 Configuration and Administration Guide for instructions how to configure BAT devices correctly.

In order to easily calculate the possible range and distance of a WLAN installation, Hirschmann provides the Antenna Distance Calculator.You can find the Antenna Distance Calculator on the supplied CD.Also you can download this Excel tool from www.beldensolutions.com.


http://www.hirschmann-ac.de

http://www.belden-solutions.com

Output power calculation

68BAT Antenna Guide

Release 02 08/2011

Fresnel Zone

11 Fresnel Zone

The Hirschmann Antenna Distance Calculator is based on the following calculation scheme:The 1st Fresnel zone has the form of an ellipsoid of rotation whereby the antennas are located in the focal points of the ellipsoid.This zone is calculated by the shaft section b of the ellipsoidb = 0.5*√ (λ*d)

d stands for the distance between the antennas (km)λ = wavelength of electromagnetic wave λ = c / fc is the speed of the wave, nearly like vacuum approx. 300,000 km/s; 186,411 miles/sf = frequency of the wave in 1/s = Hz.

Fresnel Zone


Fresnel Zone

At distance above 2 km (1.24 miles), it is necessary to add earth curvature to calculate the altitude at which the antenna has to be mounted. Some examples:

d = 2 km, d = 1.24 milesf = 2.4 GHz b = 0.5 * √ (300,000 km/s / 2.4 GHz * 2 km) = 7.9 m

b = 0.5 * √ (186,411 miles/s / 2.4 GHz * 1.24 miles) = 311 inf = 5.8 GHz b = 0.5 * √ (300,000 km/s / 5.8 GHz * 2 km) = 5 m

b = 0.5 * √ (186,411 miles/s / 5.8 GHz * 1.24 miles) = 197 in

Table 64: Examples of Fresnel Zone Calculations

5 km, 3.1 miles

=> 0.50 m, 19.7 in

10 km, 6.2 miles

=> 2.00 m, 78.7 in

70BAT Antenna Guide

Release 02 08/2011

Statement about passive antennas in hazardous environment

A Statement about passive antennas in hazardous environment

Hirschmann BAT antennas are passive devices which are not able to increase the power by themselves.

The BAT54-F X2 and BAT300-F X2 meet the requirements of EN 60 079-15 (IEC 60079-15) (type of protection: Ex nA II T4) independent of the passive accessories used.See KEMA test report No. 2109557, Annex A.1., last clause “Other issues”.

The radiated radio frequency energy is not more than 100 mW (less than 20dBm), which is acceptable for apparatus group IIC (maximum 2W allowed in accordance with TR EN 50427).

Hirschmann states that BAT antennas can be used in ATEX Zone II in operation with the certified BAT54-F X2 and BAT300-F X2.


Statement about passive antennas in hazardous environment

72BAT Antenna Guide

Release 02 08/2011

Index

B Index

AATEX Zone II 8, 71Antenna Distance Calculator 67, 69

EEN 60 079-15 71

FFAQ 75Fresnel zone 69

MMessage URL http://www.beldensolutions.com 75, 75Message URL http://www.hicomcenter.com 75, 75

RRadiating cable 54

TTR EN 50427 71, 71Technical questions 75Training courses 75

BAT FamilyRelease 02 08/2011 73

Index

74BAT Family

Release 02 08/2011

Further Support

C Further Support

Technical Questions and Training CoursesIn the event of technical queries, please contact your local Hirschmann distributor or Hirschmann office. You can find the addresses of our distributors on the Internet: www.beldensolutions.com.

Our support line is also at your disposal: Tel. +49 1805 14-1538 Fax +49 7127 14-1551

Answers to Frequently Asked Questions can be found on the Hirschmann internet site (www.beldensolutions.com) at the end of the product sites in the FAQ category. The current training courses to technology and products can be found under http://www.hicomcenter.com.

Hirschmann Competence CenterIn the long term, excellent products alone do not guarantee a successful customer relationship. Only comprehensive service makes a difference worldwide. In the current global competition scenario, the Hirschmann Competence Center is ahead of its competitors on three counts with its complete range of innovative services:

Consulting incorporates comprehensive technical advice, from system evaluation through network planning to project planing.

Training offers you an introduction to the basics, product briefing and user training with certification.

Support ranges from the first installation through the standby service to maintenance concepts.

With the Hirschmann Competence Center, you have decided against making any compromises. Our client-customized package leaves you free to choose the service components you want to use. Internet: http://www.hicomcenter.com.


Wireless LAN BAT Family Antennas - Belden...8 Radiating Cable Antennas (Leaky Cable) 53 8.1 Leaky...

Documents

Transcript of Wireless LAN BAT Family Antennas - Belden...8 Radiating Cable Antennas (Leaky Cable) 53 8.1 Leaky...