Post on 27-Jun-2020
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
Page 3 of 6
PAMECConcrete pumping & placing systems
The concrete placement boom P-DL 12 C is made up of the following parts:
• Base unit The base unit is made of a robust metal structure complete with telescopic jack arms fitted with outriggers which can be adjusted vertically to allow for a perfectly horizontal disposition of the base unit itself. A thrust bearing is fitted to the upper part of the base unit to enable the rotation of the boom. The base unit is also fitted, on request, with four wheels so that the equipment can be moved when not in operation and with the boom in the closed position.
• Pipe support boom The boom is made up of two arms: the first section is mounted on a thrust-bearing, while the second section, as part of the delivery line, is structurally supported by a steel tie. The counterweight support is attached to the other end of the boom.
• Piping The DL 12 C Distributor can be fitted with pipes with a thickness of 4mm DN 100
(collars Ø 114-127) and DN 125 (collars ∅ 141-148).
Page 4 of 6
PAMECConcrete pumping & placing systems
1 Overall drawing
Page 5 of 6
PAMECConcrete pumping & placing systems
1 Overall drawing
Page 6 of 6
PAMECConcrete pumping & placing systems
2 Technical data
Weight and loads
Weight of complete boom 1100 daN
Counterweight 1200 daN Total weight 2300 daN
Total weight at each jack arm
1400 daN
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
DR 16 B Page 3 of 6
PAMECConcrete pumping & placing systems
1.1 Overall drawing
DR 16 B Page 4 of 6
PAMECConcrete pumping & placing systems
1.2 Working area
DR 16 B Page 5 of 6
PAMECConcrete pumping & placing systems
1.3 Loads and moments MAX LOADS AND MOMENTS ACCORDING TO DIN 24117
V (vertical load): daN
Mv (overturning moment): daNm
H (horizontal load) daN
Mh (horizontal bending moment): daNm
WARNING! THE MAX WORKING WIND SPEED FOR THE CONCRETE BOOM IS 72 km/hr (25 Kg/m2) A WIND SPEEDMETER NEEDS TO BE PLACED AT THE TOP OF THE FORMWORK IN ORDER TO CHECK THE WIND SPEED DATA AT THE OPERATING WORKING HEIGHT.
WHEN SPEED WIND INCREASE OVER 15% OF THE MAXIMUM WORKING ONE (20 m/sec = 72 km/hr), IT IS ADVISABLE TO CLOSE THE BOOM IN THE NOT WORKING POSITION. (TWO ARMS IN CLOSED POSITION)
DR 16 B Page 6 of 6
PAMECConcrete pumping & placing systems
1.4 Technical data
Dimensions and space occupied by the boom
Height m
Width m
Length m
Weight and loads
Weight of the boom daN
Weight of the support daN
Total weight daN
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
DRV 12C – 55M Page 3 of 13
PAMECConcrete pumping & placing systems
1.1 Description The concrete placement boom DRV 12 C is made up of the following parts:
• Base unit The base unit is made of a robust metal structure complete with telescopic jack arms fitted with outriggers which can be adjusted vertically to allow for a perfectly horizontal disposition of the base unit itself. A thrust bearing is fitted to the upper part of the base unit to enable the rotation of the boom. The base unit is also fitted, on request, with four wheels so that the equipment can be moved when not in operation and with the boom in the closed position.
• Pipe support boom The boom is provided with two horizontal arms, which are mounted on a thrust-bearing . The movement of the second arm on the vertical plane is obtained by a hydraulic cylinder operated by a hand pump. The counterweight support is attached to the other end of the boom. The ballast container is optional.
• Piping The DRV 12 C distributor can be fitted with pipes with a thickness of 4mm
DN 100 (collars Ø 114-127) and DN 125 (collars ∅ 141-148). The length of the terminal rubber hose is 1,5 m
DRV 12C – 55M Page 4 of 13
PAMECConcrete pumping & placing systems
1.2 Overall drawing
DRV 12C – 55M Page 5 of 13
PAMECConcrete pumping & placing systems
1.2 Overall drawing
DRV 12C – 55M Page 6 of 13
PAMECConcrete pumping & placing systems
1.3 Counterweight drawing
DRV 12C – 55M Page 7 of 13
PAMECConcrete pumping & placing systems
1.4 Technical data
Weight and loads
Weight of complete boom 2.400 kg
Counterweight 1.650 kg
Total weight 4.050 kg
Total weight at each jack arm 2.670 kg
DRV 12C – 55M Page 8 of 13
PAMECConcrete pumping & placing systems
1.5 Applications
DRV 12C – 55M Page 9 of 13
PAMECConcrete pumping & placing systems
1.5 Applications
DRV 12C – 55M Page 10 of 13
PAMECConcrete pumping & placing systems
1.5 Applications
DRV 12C – 55M Page 11 of 13
PAMECConcrete pumping & placing systems
DRV 12C – 55M Page 12 of 13
PAMECConcrete pumping & placing systems
DRV 12C – 55M Page 13 of 13
PAMECConcrete pumping & placing systems
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
BVZ 12 C Page 3 of 9
PAMECConcrete pumping & placing systems
1.1 Overall drawing
BVZ 12 C Page 4 of 9
PAMECConcrete pumping & placing systems
1.2 Working area
1st arm : 0° ÷ 89°
2nd arm : 0° ÷ 180°
3rd arm : 0° ÷ 180°
BVZ 12 C Page 5 of 9
PAMECConcrete pumping & placing systems
1.3 Loads and moments MAX LOADS AND MOMENTS ACCORDING TO DIN 24117
V (vertical load): 5540 daN
L1 max (vertical load at outrigger): 120 daN
L2 min (vertical load at outrigger): 2615 daN
W (wind force): 150 daN
Mr (overturning moment): +4470/-5690 daNm
Mt (torque moment): 575 daNm
Mw (wind moment): 630 daNm
WARNING! THE MAX WORKING WIND SPEED FOR THE CONCRETE BOOM IS 72 km/hr (25 Kg/m2) A WIND SPEEDMETER NEEDS TO BE PLACED AT THE TOP OF THE CLIMBING FORMWORK IN ORDER TO CHECK THE WIND SPEED DATA AT THE OPERATING WORKING HEIGHT.
WHEN SPEED WIND INCREASE OVER 15% OF THE MAXIMUM WORKING ONE (20 m/sec = 72 km/hr) , IT IS ADVISABLE TO CLOSE THE BOOM IN THE NOT WORKING POSITION. (THREE ARMS CLOSED AND IN VERTICAL POSITION)
BVZ 12 C Page 6 of 9
PAMECConcrete pumping & placing systems
1.4 Technical data
Dimensions and space occupied by the boom
Height 2150 mm
Width 2300 mm
Length 7100 mm
Weight and loads
Weight of complete boom 2900 kg
Counterweight 1650 kg
Total weight 4550 kg
Total weight at each jack arm 2615 kg
Technical data for the basic set up
Electric power 380/440 V
Three-phase + neutral + earth
Frequency 50/60 Hz
Power of the electric motor 4 kW
Technical data for the hydraulic power pack
Oil flow 8.7 lit/min
Maximum pressure 245 bar
BVZ 12 C Page 7 of 9
PAMECConcrete pumping & placing systems
1.5 Annexes
BVZ 12 C Page 8 of 9
PAMECConcrete pumping & placing systems
1.5 Annexes
BVZ 12 C Page 9 of 9
PAMECConcrete pumping & placing systems
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
BVR 12 C Page 3 of 6
PAMECConcrete pumping & placing systems
1.1 Overall drawing
BVR 12 C Page 4 of 6
PAMECConcrete pumping & placing systems
1.2 Working area
1st arm : 0° ÷ 89°
2nd arm : 0° ÷ 180°
3rd arm : 0° ÷ 180°
BVR 12 C Page 5 of 6
PAMECConcrete pumping & placing systems
1.3 Loads and moments MAX LOADS AND MOMENTS ACCORDING TO DIN 24117
V (vertical load): 5540 daN
L1 max (vertical load at outrigger): 120 daN
L2 min (vertical load at outrigger): 2615 daN
W (wind force): 150 daN
Mr (overturning moment): +4470/-5690 daNm
Mt (torque moment): 575 daNm
Mw (wind moment): 630 daNm
WARNING! THE MAX WORKING WIND SPEED FOR THE CONCRETE BOOM IS 72 km/hr (25 Kg/m2) A WIND SPEEDMETER NEEDS TO BE PLACED AT THE TOP OF THE CLIMBING FORMWORK IN ORDER TO CHECK THE WIND SPEED DATA AT THE OPERATING WORKING HEIGHT.
WHEN SPEED WIND INCREASE OVER 15% OF THE MAXIMUM WORKING ONE (20 m/sec = 72 km/hr) , IT IS ADVISABLE TO CLOSE THE BOOM IN THE NOT WORKING POSITION. (THREE ARMS CLOSED AND IN VERTICAL POSITION)
BVR 12 C Page 6 of 6
PAMECConcrete pumping & placing systems
1.4 Technical data
Dimensions and space occupied by the boom
Height 2150 mm
Width 2300 mm
Length 7100 mm
Weight and loads
Weight of complete boom 2900 kg
Counterweight 1650 kg
Total weight 4550 kg
Total weight at each jack arm 2615 kg
Technical data for the basic set up
Electric power 380/440 V
Three-phase + neutral + earth
Frequency 50/60 Hz
Power of the electric motor 4 kW
Technical data for the hydraulic power pack
Oil flow 8.7 lit/min
Maximum pressure 245 bar
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
BV 08 TR – 55M Page 3 of 8
PAMECConcrete pumping & placing systems
1 Overall drawing
BV 08 TR – 55M Page 4 of 8
PAMECConcrete pumping & placing systems
1 Overall drawing
BV 08 TR – 55M Page 5 of 8
PAMECConcrete pumping & placing systems
2 Working area
BV 08 TR – 55M Page 6 of 8
PAMECConcrete pumping & placing systems
3 Technical data
Dimensions and space occupied by the boom
Height 2263 mm
Width 2369 mm
Length 4290 mm
Weight and loads
Weight of complete boom 4400 kg
Weight of the concrete 385 kg
Total weight 4785 kg
Technical data for the basic set up
Power 31 HP
Fuel: gasoline with a minimum of 85 octane
Technical data for the hydraulic power pack
Oil flow 12.5+12.5 lit/min
Maximum pressure 180 bar
BV 08 TR – 55M Page 7 of 8
PAMECConcrete pumping & placing systems
BV 08 TR – 55M Page 8 of 8
PAMECConcrete pumping & placing systems
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMEC SPRAYING UNIT Technical Data ________________________________________________________________________ Dimensions and working range
Transport length 2.3 m Transport width 1.6 m Transport height 2.2 m Weight 1900 Kg Outriggers 2.7
Page 6 of 3
PAMECConcrete pumping & placing systems
PAMEC SPRAYING UNIT Technical specifications ________________________________________________________________________
Power Input supply voltage Protection class
3x400/500 7.5 55
V/Hz Kw IP
Spraying range Max height (incl. 1.5 m nozzle distance)
Max width (incl. 1.5 m nozzle distance)
6 4
m m
Hydraulic Max pressure Oil tank
180 100
Bar l
Carrier vehicle 2 rubber tracks, with individual hydraulics drive Diesel engine, liquid cooled (LOMBARDINI)
19.5
KW
Delivery pipeline Hose size
65 mm
Stabilization Hydraulic outriggers
Control Remote control with 15 m cable OPTIONAL ________________________________________________________________________
• Dosing unit
Voltage
400/440 V
Frequency
50/60 Hz
Electric motor
0.75 Kw
Max delivery pressure
10 Bar
Delivery volume 2 - 10.2 l/min • Tank
Inox 350 l
• Radio remote control
PAMEC
PAMEC S.r.l. - 66054 VASTO - Italia - Z.I. Punta Penna
Tel.: +39.0873.310000 - Fax: +39.0873.311787 - E-mail: info@pamec.com
Concrete pumping & placing systems
BVR 12C/N – 55M Page 3 of 6
PAMECConcrete pumping & placing systems
1.1 Overall drawing
BVR 12C/N – 55M Page 4 of 6
PAMECConcrete pumping & placing systems
1.2 Working Area
1st arm : 0° ÷ 89°
2nd
arm : 0° ÷ 180°
3rd
arm : 0° ÷ 180°
BVR 12C/N – 55M Page 5 of 6
PAMECConcrete pumping & placing systems
1.3 Loads and moments MAX LOADS AND MOMENTS ACCORDING TO DIN 24117
V (vertical load): 5889 daN
L1 min (vertical load at outrigger): 454 daN
L2 max (vertical load at outrigger): 2491 daN
W (wind force): 130 daN
Mr (overturning moment): +5200/-4750 daNm
Mt (torque moment): 300 daNm
Mw (wind moment): 498 daNm
WARNING! THE MAX WORKING WIND SPEED FOR THE CONCRETE BOOM IS 72 km/hr (25 Kg/m2) A WIND SPEEDMETER NEEDS TO BE PLACED AT THE TOP OF THE CLIMBING FORMWORK IN ORDER TO CHECK THE WIND SPEED DATA AT THE OPERATING WORKING HEIGHT. WHEN SPEED WIND INCREASE OVER 15% OF THE MAXIMUM WORKING ONE (20 m/sec = 72 km/hr) , IT IS ADVISABLE TO CLOSE THE BOOM IN THE NOT WORKING POSITION. (THREE ARMS CLOSED AND IN VERTICAL POSITION)
BVR 12C/N – 55M Page 6 of 6
PAMECConcrete pumping & placing systems
1.4 Technical data
Dimensions and space occupied by the boom
Height 2,408 m
Width 2,388 m
Length 7,000 m
Weight and loads
Weight of complete boom 3105 daN
Counterweight 1648 daN
Total weight 4753 daN
Total weight at each jack arm 2491 daN
Technical data for the basic set up
Electric power 380/44
0 V
Three-phase + neutral + earth
Frequency 50/60 Hz
Power of the electric motor 4 kW
Technical data for the hydraulic power pack
Oil flow 8.7 lit/min.
Maximum pressure 245 bar
PAMECConcrete pumping & placing systems
PHOTO GALLERY (DRAFT)
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems
PAMECConcrete pumping & placing systems