Post on 20-Jul-2020
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2015 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
WIRELESS CHARGERserved. AII02174-56 (150
2016 ACCORD2- AND 4-DOOR
8) 0
Issue Date
AUG 2015
PARTS LIST
Wireless Charger Attachment KitP/N 08U58-T2A-100A
Wireless charger harness
Lower tray
8 Wire ties
Wire tie with clip
20 A Fuse
Fuse label
Ground bolt
4 Self-tapping screws
Urethane tape
Wireless Charger Unit KitP/N 08U58-T2A-100
Wireless charger unit
Accessory user’s information manual
1 of 158U58-T2A-1000-90
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Isopropyl alcohol
Shop towel
Diagonal cutters
10 mm and 17 mm Open end wrenches
Tape
Ratchet
10 mm Socket
The following tool is available through the Honda Tool andEquipment Program. On the iN, click on Service >Service Bay > Tool and Equipment Program, then enterthe number under “Search”. Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014)
Illustration of the Wireless Charger on the Vehicle
QE20310BC
WIRELESSCHARGERUNIT
3 A FUSE
20 A FUSE
2 of 15 AII02174-5
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”
1. Disconnect the negative cable from the battery.
2. If equipped, remove the driver’s dashboard undercover.
QB20201AB
2 CLIPS
DRIVER’S DASHBOARDUNDER COVER
KNOB(Turn.)
6 (1508) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
3. Remove the driver’s dashboard lower cover andunplug the vehicle connectors.
QB20202AB
DRIVER’S DASHBOARDLOWER COVER
9 CLIPSVEHICLECONNECTORS
4. Using the ignition key, unlock the trunk lid/fuel filldoor opener, then remove the ignition key. Removethe key cover.
QB20803AB
KEYCOVER
6 RETAININGTABS
TRUNK LID/FUELFILL DOOR OPENER
Unlock.
IGNITIONKEY
SELF-TAPPINGSCREW
DRIVER’S DOORSILL TRIM
5. Remove the self-tapping screw from the trunk lid/fuelfill door opener cover.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02174-5
6. Remove the driver’s door sill trim.
4-Door: Two retaining tabs and four clips.
20804A
4 CLIPS
2 RETAINING TABS
DRIVER’S DOORSILL TRIM
2-Door: Two retaining tabs and six clips.
32102A
6 CLIPS
2 RETAINING TABS
DRIVER’S DOORSILL TRIM
6 (1508) 3 of 15
7. Pull away the door opening seal and remove thedriver’s kick panel.
QB20805AB
2 CLIPS
DRIVER’SKICK PANEL
DOOR OPENINGSEAL(Pull away)
8. Attach tape to the instrument panel as shown.
QE12801AC
TAPE
TAPE
INSTRUMENTPANEL
INSTRUMENTPANEL
BOTTOM VIEW
4 of 15 AII02174-5
If the vehicle has M/T, go to step 9; otherwise, go tostep 14.
M/T models
9. Attach the tape to the center console panel asshown.
QE60801AA
TAPE
CENTERCONSOLEPANEL
6 (1508) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
Shift lever knob type A, go to step 10; shift lever knobtype B, go to step 12.
Shift lever knob type A
10. Release the ring and lower the shift lever boot.
QE60802AA
Push
SHIFTLEVERKNOB
2 RETAININGTABS
SECTION VIEW
RING
Push
SHIFTLEVERBOOT
SHIFTLEVERBOOT
SHIFT LEVER KNOB(Turn counterclockwise.)
11. Remove the shift lever knob. Go to step 16.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02174-5
Shift lever knob type B
12. Remove the shift lever knob.
QE60803AA
SHIFTROD
SHIFT LEVER KNOB(Turn counterclockwise.)
13. Release the shift lever boot. Using a 17 mm openend wrench, remove the lock nut. Go to step 16.
QE60804AA
SHIFTROD SECTION VIEW
RING
SHIFTLEVERBOOT
SHIFTLEVERBOOT
LOCK NUT(Turncounterclockwise.) LOCK
NUT
SHIFTROD
6 (1508) 5 of 15
Except M/T models
14. Move the shift lever knob to the D position.
QE12901ACSHIFT LEVER KNOB(Move to the D position.)
15. Attach tape to the shift lever knob and centerconsole panel as shown.
QE12902AC
TAPE
CENTERCONSOLEPANEL SHIFT LEVER
KNOB
6 of 15 AII02174-5
16. Remove the left center console side trim.
QE12903AC
10 CLIPS
RIGHT CENTERCONSOLE SIDETRIM
LEFT CENTERCONSOLE SIDETRIM
17. Remove the right center console side trim the sameway.
18. Remove the center pocket and unplug the vehicleconnector.
QE12904AC2 SCREWS
VEHICLECONNECTOR
CENTERPOCKET
6 (1508) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
19. Open the armrest, remove the center console panel,and unplug the vehicle connectors.
QE12905AC
VEHICLECLIP
CENTERCONSOLEPANEL
10 CLIPS
VEHICLECONNECTORS
CENTERCONSOLEPANEL
ARMREST
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02174-5
20. Remove the vehicle lower tray from the centerconsole panel.
QE12906BCCLIP
VEHICLELOWER TRAY
CENTERCONSOLEPANEL
2 SCREWS
21. Remove the vehicle lower tray lid.
QE13001AC
VEHICLELOWER TRAYLID
2 CLIPS
2 RETAININGTABS
VEHICLELOWER TRAY(Discard.)
6 (1508) 7 of 15
22. Install the wireless charger unit on the lower tray withfour self-tapping screws.
QE13002BC
4 SELF-TAPPINGSCREWS
LOWERTRAY
WIRELESSCHARGERUNIT
23. Install the vehicle lower tray lid removed in step 21.
QE13003AC
VEHICLELOWER TRAYLID
LOWERTRAY
2 RETAININGTABS
2 CLIPS
8 of 15 AII02174-5
24. Install the lower tray on the center console panel withtwo screws and one clip removed in step 20.
QE13004BC
CENTERCONSOLEPANEL
LOWERTRAY
2 SCREWS
CLIP
25. Using isopropyl alcohol on a shop towel, thoroughlyclean the fuse case where the fuse label will attach.Attach the fuse label (3 A WIRELESS CHARGER)on the fuse case.
QE13005AC
FUSECASE3 A FUSE
LABEL
WIRELESSCHARGERHARNESS
Clean withisopropylalcohol.
6 (1508) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
26. Using isopropyl alcohol on a shop towel, thoroughlyclean the area where the urethane tape will attach.
QE13006AC
Clean withisopropylalcohol.
VEHICLEPANEL
URETHANETAPE
27. Attach the urethane tape to the vehicle panel asshown.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02174-5
If the vehicle is equipped with an accessory 4-pinconnector, go to step 29; otherwise, continue withstep 28.
Without accessory harness 4-pin connector
28. Plug the wireless charger harness 4-pin connectorinto the fuse box. Go to step 31.
QE13007AC
Plug in here.
FUSE BOX
FRONT VIEW
WIRELESSCHARGERHARNESS4-PINCONNECTOR
FUSE BOX
6 (1508) 9 of 15
Vehicles equipped with an accessory 4-pin connector
29. Unplug the other accessory harness 4-pin connectorfrom the fuse box and plug it into the wirelesscharger harness 4-pin connector.
QE13008AC
FRONT VIEWFUSE BOX
Plug in here.
WIRELESSCHARGERHARNESS4-PINCONNECTORS
FUSE BOX
OTHER ACCESSORYHARNESS4-PIN CONNECTOR
30. Plug the remaining wireless charger harness 4-pinconnector into the fuse box.
10 of 15 AII02174-5
If the vehicle is already equipped with anotheraccessory 8-pin connector, go to step 32; otherwise,continue with step 31.
Without accessory harness 8-pin connector
31. Plug the wireless charger harness 8-pin connectorinto the fuse box. Go to step 34.
QE020201AC
Plug in here.
FUSE BOX
FRONT VIEW
WIRELESSCHARGERHARNESS8-PINCONNECTOR
FUSE BOX
6 (1508) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
With other accessory harness 8-pin connector
32. Unplug the other accessory harness 8-pin connectorfrom the fuse box and plug it into the wirelesscharger harness 8-pin connector.
QE20202AC
FRONT VIEWFUSE BOX
Plug in here.
WIRELESSCHARGERHARNESS8-PINCONNECTORS
FUSE BOX
OTHER ACCESSORYHARNESS8-PIN CONNECTOR
DUMMYCONNECTOR(Discard.)
33. Plug the remaining wireless charger harness 8-pinconnector into the fuse box.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02174-5
If the vehicle is already equipped with otheraccessory harness, go to step 35; otherwise,continue with step 34.
Without other accessory harness
34. Attach one wire tie with clip around the white tape onthe wireless charger harness, then secure theharness to the hole in the vehicle panel with the clip.Go to step 37.
QE20203ACWIRELESSCHARGERHARNESS
VEHICLEPANEL
WHITETAPE
WIRE TIEWITH CLIP
WIRELESSCHARGERHARNESS
VEHICLEPANELHOLE
6 (1508) 11 of 15
With other accessory harness
35. Using diagonal cutters, cut the clip portion off of onewire tie with clip.
QE20204ACWIRELESSCHARGERHARNESS
WIRELESSCHARGERHARNESS
OTHERACCESSORYHARNESS
WIRE TIEWITH CLIP
WIRE TIEWITH CLIP CLIP
Cut off.
WHITETAPE(Align)
36. Attach the cut wire tie with clip around the white tapeon the wireless charger harness and secure thewireless charger harness to the other accessoryharness with one wire tie with clip.
12 of 15 AII02174-5
37. Secure the wireless charger harness, wirelesscharger harness 4-pin connector, and wirelesscharger harness 8-pin connector to the vehicleharness with two wire ties.
QE20205AC
WIRELESSCHARGERHARNESS8-PINCONNECTOR
WIRELESSCHARGERHARNESS4-PINCONNECTOR
VEHICLEHARNESS
2WIRETIES
WIRELESSCHARGERHARNESS
VEHICLEHARNESS
38. Remove the vehicle ground bolt and secure thewireless charger harness ground terminal to thevehicle ground terminals with one ground bolt. Donot put the ground terminal calkings on top of oneanother.
QE20206AC
WIRELESSCHARGERHARNESSGROUNDTERMINAL
VEHICLEGROUNDTERMINALS
GROUNDBOLT
VEHICLEGROUND BOLT(Discard.)
6 (1508) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
39. Secure the wireless charger harness 12-pinconnector and wireless charger harness to thevehicle harness with two wire ties.
QE20301AC
WIRELESSCHARGERHARNESS
VEHICLEHARNESS
2WIRETIES
WIRELESSCHARGERHARNESS12-PINCONNECTOR
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02174-5
40. Align the white tape on the wireless charger harnesswith the vehicle clip and secure the wireless chargerharness to the vehicle harness with one wire tie.
QE20304BC
WIRELESSCHARGERHARNESS
WHITETAPE(Align.)
WIRETIE
VEHICLECLIP
WIRELESSCHARGERHARNESS
VEHICLEHARNESS
WIRETIE
WIRELESSCHARGERHARNESS
WHITETAPEVEHICLE
HARNESS
41. Secure the wireless charger harness to the vehicleharness with one wire tie at the white tape on thewireless charger harness.
6 (1508) 13 of 15
42. Secure the wireless charger harness to the vehicleframe with one wire tie at the white tape on thewireless charger harness.
QE20305BC
WIRELESSCHARGERHARNESS VEHICLE
CLIP
WIRE TIEVEHICLEHARNESS
VEHICLEFRAME
WIRELESSCHARGERHARNESS
WIRETIE
WHITETAPE
43. Secure the wireless charger harness to the vehicleharness with one wire tie.
14 of 15 AII02174-5
44. Plug the wireless charger harness 7-pin connectorinto the wireless charger unit.
QE20306AC
CENTERCONSOLEPANEL
WIRELESSCHARGERHARNESS7-PINCONNECTOR
WIRELESSCHARGERUNIT
CENTERCONSOLEPANELHOLE
WIRELESSCHARGERHARNESSCLIP
45. Secure the wireless charger harness to the centerconsole panel with one clip on the wireless chargerharness. Install the center console panel.
6 (1508) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
46. Plug the 20 A fuse into the fuse box.
QE20308AC
Plug in here.
FUSE BOX
FRONT VIEW
FUSE BOX20 A FUSE
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02174-5
47. Using isopropyl alcohol on a shop towel, thoroughlyclean the area where the fuse label will attach.Attach the fuse label to the fuse seal on the driver’skick panel.
QE20309AC
FUSESEAL
FRONT VIEW
ATTACHINGPOINT (NO.38)(20A WIRELESSCHARGER)
FUSE LABEL(20A WIRELESSCHARGER)
FUSESEAL
DRIVER’S KICKPANEL
Clean withisopropyl alcohol
48. Check that all wire harnesses are routed properlyand all connectors are plugged in.
49. Reinstall all removed parts.
50. Reconnect the negative cable to the battery.
51. Press and hold the audio unit power button for 2seconds to restore the audio unit and navi (ifequipped) system functions.
52. Reset the clock (vehicles without navigation).
Check the Operation of the Wireless Charger
53. Check that the wireless charger is working properlyas described in the Accessory User’s InformationManual supplied with this kit.
6 (1508) 15 of 15