Post on 30-Jun-2020
ENGINEERING GRAPHICS
By
R.Nathan
Assistant Professor
Department of Mechanical Engineering
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
I - SEMESTER LECTURE NOTES
UNIT – 4
“SECTION OF SOLIDS”
Engineering Graphics GE - 2111
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
SECTION OF SOLIDS
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
SECTION OF SOLIDS
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
CROSS SECTION OF SOLIDS
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
SECTIONING SYMBOLS
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
TERMS & CONVENTIONS
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
TYPES OF SECTIONS
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
METHOD OF HATCHING
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
Engineering Graphics Lecture Notes
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
I - SEMESTER 04.10.2012
TECHINIQUES FOR SECTIONAL VIEWS
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
TYPES FOR SECTIONAL VIEWS – SECTIONAL FRONT VIEW
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
TYPES FOR SECTIONAL VIEWS – SECTIONAL TOP VIEW
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
SECTIONAL VIEW – PARALLEL TO H.P AND PERPENDICULAR TO V.P
A cube of 40 mm sideis cut by a horizontal section plane, parallel to
H.P at a distance of 15 mm from the top end. Draw the sectional top
view and front view
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
SECTIONAL VIEW – INCLINED TO H.P AND PERPENDICULAR TO V.P
A square prism of base side 50 mm and height of axis 80 mm has its
base on H.P, it is cut by a section plane perpendicular to V.P and
inclined to H.P such that it passes through the two opposite corners of
the rectangular face in front. Draw the sectional Top View and Front
View. Find the angle of inclination of the section plane
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
SECTIONAL VIEW – PERPENDICULAR TO H.P AND INCLINED TO V.P
A square prism of base side 40 mm and height 70 mm is resting on its
rectangular face on the ground such that its axis is parallel to H.P &V.P,
it is cut by a section plane perpendicular to H.P &incllined to V.P at an
angle of 45° and passing through a point 10 mm from one of its ends.
Draw the sectional Front View and Top View
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
TRUE SHAPE OF A SECTION
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
PROCEDURE FOR TRUE SHAPE
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES
C.R.ENGINEERING COLLEGEAlagarkovil, Madurai - 625301
EXAMPLE: TRUE SHAPE PROBLEM
A square prism of base side 50 mm and height of axis 80 mm has its
base on H.P, it is cut by a section plane perpendicular to V.P and
inclined to H.P such that it passes through the two opposite corners of
the rectangular face in front. Draw the sectional Top View and Front
View and true shape of the section
Engineering Graphics GE - 2111
I - SEMESTER LECTURE NOTES