Post on 10-Jul-2020
KEY FEATURES
+ Rotating spray
+ 360° cleaning pattern
+ Ideal for small to medium-sized tanks
+ Low pressure
+ Low use of cleaning medium
Bio 7SBScanjet tank cleaning equipment
The Scanjet Bio 7SB is a new type of Rotary Spray Head (RSH) tank cleaning
device. Compared with conventional static devices, the Bio 7SB is very efficient,
saving water and chemicals while improving cleaning effectiveness. The Bio 7SB
employs a unique fluid bearing rotary mechanism, with a service life two to three
times that of traditional ball bearing rotary devices.
The choice of either a clip-on (pin), weld-on or threaded connection means the Bio
7SB is always easy to install, whether building a new CIP tank cleaning system or
upgrading an existing one based on ordinary static or rotary spray devices.
With 360° impact coverage, self-cleaning and self-draining features, the Bio 7SB
design follows EHEDG and GMP guidelines, and can be supplied with EN10204-
2.1, 2.2 or 3.1 material and FDA 21CFR compliance certificates. The Bio 7SB-XXX-A
clip-on and weld-on versions have attained 3A certification under sanitary standard
78-01. Surface finish roughness supplied as standard is Ra = 0.8 μm (30 μ inch);
other surfaces are available upon request.
The Bio 7SB can be used in conjunction with the Scanjet WASHTRAC sensor to
monitor and verify its operation and performance.
The Bio 7SB is the first choice for anyone looking for the most advanced Rotary
Spray Head tank cleaning device available.
The Scanjet Bio 7SB Rotary Spray Head can be used in a wide range of
applications, including:
+ Mixing vessels
+ Blending tanks
+ Beverage tanks
+ Dairy tanks
+ Yeast tanks
+ Reactors
+ IBCs
1 1,5 2 2,5 3 3,5 4 4,5 5
0
4
8
12
16
20
24
28
20 30 40 50 60 70
0
40
80
120
20
60
100
m3/h USgpm
psi
bar
1 1,5 2 2,5 3 3,5 4 4,5 5
0
1
2
3
4
0,5
1,5
2,5
3,5
20 30 40 50 60 70
0
1
2
3
4
5
6
7
8
9
10
11
12
13
m ft
bar
psi
Wetting
Impact cleaning
360º SPRAY PATTERN
1¼" BSPf1¼" NPTf
THREADCONNECTION
Ø 38/35.6(ID) (1.5/1.4 in)
115
(4.5
3 in
)
Ø 65 (2.56 in)
WELDCONNECTION
Ø 38.4/41.6(OD) (1.51/1.64 in)Ø 38.3/41.4(OD) (1.5/1.63 in)
PINCONNECTION
¾" BSP¾" NPT
THREADCONNECTION
25/22,5(OD)
45
75
WELDCONNECTION
25,6/ 28,6(ID/OD)25,3/28,3(ID/OD)
PINCONNECTION
360º SPRAY PATTERN
*Because of variations in part wear, water temperature, installation etc., the flow may differ ±10% from specified value.Continuous product improvement is the policy of Scanjet Group and we reserve the right to alter the specifications at any time without prior notice. Errors and omissions excepted.All trademarks, designs and other intellectual property depicted here are property of the Scanjet Group unless otherwise stated, and may be registered, patented or otherwise protected in certain jurisdictions.Copyright © Scanjet Group. All rights reserved.
Technical performance Dimensions
Specifications
Flow* 10.7-27.5 m³/h (47-120 USgpm)
Inlet pressure 1-5 bar (14-72 psi)
Max pressure 5 bar (72 psi)
Recommended pressure 3 bar (43 psi)
Max working temperature 95°C (200°F)
Max ambient temperature 150°C (300°F)
Weight 452-477 g (15.94-16.83 oz)
Connections Weld connection
Pin connection
1¼” BSPf / 1 ¼” NPTf
Material EN1.4404/PEEK
Lubrication Self lubricated by media
Pressure/Flow
Cleaning radius
Scanjet Systems AB P.O. Box 9316 SE-400 97 Göteborg SwedenPhone + 46 31 3387530 Fax + 46 31 3387540 E-mail sales@scanjetsystems.comWeb www.scanjetsystems.com
* Clip-on models have approx. 0,5 m³/h higher flow rate