203 359 44 714 IS 862291102 EN/PDF 120503
42104744.eps
Technical dataD-Balancers D-BP 55 and D-BP 110
2033
5944
.p65
/120
503
2
Part nos.
The Demag rope balancer is available with two different piston seals. If the devicesare ordered with Demag controls, the type of control determines the type of seal.
Depending on the application, the basic units differ in the type of piston seal.
Available are:
1. Low-friction type with T-type seal.
For applications in which the load is to be moved with low manual force withoutcontrol pendant.
Used e.g. in connection with a 1-, 2-, n-load balancer control, as well as with theelectro-pneumatic manual force control.
Due to physical reasons, this seal lets escape a small quantity of air.
This type is less suitable for applications in which the load is to be held over alonger period of time, even if the compressed air supply of the cylinder is inter-rupted (e.g. up/down operation).
2. Optimized seal tightness type with U-type seal.
For applications in which loads are to be moved by means of the control pen-dant and are to be moved by hand only in a small range. If the compressedair supply of the cylinder is interrupted, the load is held in position over a longperiod of time.
Used e.g. in connection with an up/down control, which allows manual move-ment of the load only within the air cushion range, i.e. it springs back into itsoriginal position.
The rope balancer should not be used in connection with a busbar lineintegrated in the KBK rail, since the manual force required for the ropebalancer is lower than the force required for displacing the current collector.
Selection of the basic unit dependingon the application and type of seal
Note:
55PB-DrecnalabeporgameD.ontraP64020229 laesepyt-UhtiwtinucisaB64120229 laesepyt-ThtiwtinucisaB64110229 lortnocnwod/puhtiw64210229 RGB-Ddnalortnocnwod/puhtiw64310229 lortnocrecnalabdaol-1htiw64410229 lortnocrecnalabdaol-2htiw64510229 lortnocecroflaunamhtiw
011PB-DrecnalabeporgameD.ontraP64220229 laesepyt-UhtiwtinucisaB64320229 laesepyt-ThtiwtinucisaB64100229 lortnocnwod/puhtiw64200229 RGB-Ddnalortnocnwod/puhtiw64300229 lortnocrecnalabdaol-1htiw64400229 lortnocrecnalabdaol-2htiw64500229 lortnocecroflaunamhtiw
2033
5944
.p65
/120
503
3
Dimensions
SWL
Rope balancers are used with a supply pressure of 6 bar (max. permissible pressure10 bar, with limited service life of the mechanical components).
The SWL specified is based on a pressure loss of the control of 0.5 bar.
Pneumatic and electro-pneumatic controls require a pressure difference betweenthe system pressure and the internal pressure in the cylinder of 0.5 bar, in order tobe able to move loads with lower manual forces and at higher speeds.
42541244.eps 42541344.eps 42541544.eps 42541744.eps
42541244.eps 42541444.eps 42541644.eps 42541844.eps
)1).mid-C(thgieHxhtdiWxhtgneL
lortnocnwod/pU lortnocrecnalabdaol-1 lortnocrecnalabdaol-2 lortnocecroflaunaM
55PB-D 544x803x524 014x803x524 014x803x524 857x803x524
011PB-D 774x533x805 924x533x805 924x533x805 318x533x805
lortnocnwod/pURGB-Dronrevogdeepshtiw
lortnocrecnalabdaol-1tinuleviws.lcni
lortnocrecnalabdaol-2tinuleviws.lcni
)2tinucisaB
55PB-D 544x803x524 725x803x524 725x803x524 322x803x524
011PB-D 774x533x805 645x533x805 645x533x805 052x533x805
eloherobeyenoisnepsusfoertnecmorfsnoisnemidthgieH)14egapeestinucisabfosnoisnemidngiseD)2
taLWS
rab3 rab4 rab5 rab6 rab7 rab8 rab9 rab01
55PB-D gk52 gk53 gk54 gk55 gk56 gk57 gk58 gk59
011PB-D gk05 gk07 gk09 gk011 gk031 gk051 gk071 gk091
2033
5944
.p65
/120
503
4
Suspension heights, rope The standard rope length of the Demag D-BP rope balancer is 6 m including thesafety windings on the rope drum. The length is divided into 1.25 m safety windingsalways remaining on the drum, 2 m max. hook path and 2.75 m dead rope. Thisresults in a max. suspension height of 4.75 m – from the lower edge of the ropebalancer. If the rope balancer is to be fitted at larger suspension heights, a longerrope can be ordered for this specific case (please state when ordering).
Available as special ropes are
• special steel ropes (require shorter maintenance intervals))• 6-strand ropes, especially for the American market, part no.: 826 621 44• easily bending ropes, particularly suitable, if the rope is to be lead through addi-
tional rope sheaves. Part no.: 826 777 44
All ropes have a diameter of 5 mm.
For the up/down control the DSK control pendant is equipped with a 3.5 m longsupply cable as standard. The control pendant should be suspended at a height ofapprox. 1 -1.5 m above floor level. If the rope balancer is fitted at larger suspensionheights (> 4.5 m), a longer supply cable is required for the DSK control pendant.
The manual force control is equipped with a helical cable with a standard length of2.8 m (extended) for transmitting the electric signals from the D Grip. This limits thesuspension height to max. 3.8 m from the lower edge of the rope balancer.
Larger suspension heights require a special helical cable which must be statedadditionally when ordering (please state suspension height).
Shortening the helical cable will not result in a reduction of the C dimension.
Interface for load handling deviceSee load handling devices for fitting to quick-release coupling, e.g. hook forquick-release coupling, PGS etc.
Swivel unit incl. rope socket (part no.: 773 260 44)
Rope socket
Part no.: 151 837 99
Rope socket, cranked
Part no.: 826 557 44
42541944.eps
42540944.eps
2033
5944
.p65
/120
503
5
Hook assembly
Part no. 826 640 44
42541144.eps
D Grip with swivel unit and rope socket
42543644.eps
Part no. 826 641 44primarily for the US market
D Grip solo
2033
5944
.p65
/120
503
6
h6
R25
b4
b3
A
A
B
B
X
h2h1
b1 b2
b
h5
l3
l5
b5
R
A
B
d1
l4
h7
l
h4h3
l2l1
d2
42104544.eps
Dimensions
Bore hole for M8 thread “screw-cut”
Thread cutting screw, DIN 7500 EE M8 x 30Part no. 324 737 99 (4 off)
Connecting plate notincluded in the scopeof supply
Detail X
Detail A
eziS b 1b 2b 3b 4b 5b 1d 2d 1h 2h 3h 4h 5h 6h 7h l 1l 2l 3l 4l 5l.nim .xam
55PB-D 524 602 912
23 05 86 57 5,61
491 42 991 791 42
01 41
6 803 29
051
401
051
56
011PB-D 805 042 862 612 72 912 812 22 12 533 501 611 35
2033
5944
.p65
/120
503
7
Mounting The rope balancer may either be suspended from the suspension eyes of the hous-ing or from the thread cutting screw DIN 7500 EE M8 x 30, part no. 324 737 99(4 off) according to the bore hole pattern on the lower side of the housing (see di-mension l4 / b5).
For connecting the rope balancer to KBK, the load bar must be used(part no. 984 685 44).
Dimension h4 in the dimension table is without clamp section and buffer on therope. If required, dimension h4 is increased by 19 mm in both cases.
If the universal pin set (external fitting) is used for fitting to the D Lift, the connectingplates may be fitted on the suspension eyes from the outside (max. plate thickness6 mm).
If the electro-pneumatic manual force control is used for D-BP 55 and D-BP 110rope balancers, attention must be paid to the fact that overhead mounting (com-pressed air supply on the lower side or rope outlet on the top) is not allowed. Anyother mounting position is possible.
All other control types may be mounted in any position.
Overhead mounting
42540744.eps
Universal pin set for fitting to the inside of the suspension eyes,part no.: 826 548 44. Maximum width of the suspension 31 mm.
2033
5944
.p65
/120
503
8
Weights
Power supply Compressed air quality
acc. to ISO 8573-1
Solid particles class 3 (< 5 mm)
Water class 4 (dew point < +3°C)
Oil class 4 (< 5 mg/m³)
Compressed air connection
Connection of the supply line via plug-in connector NW 7.2 mm or NPT 3/8" thread(for USA only)
Voltage (only for manual force control)
100 - 240 V AC single-phase, 47 - 63 Hz
Accessories
For setting the parameters of the manual force control an operator terminal withextension cable is required (part no.: 650 090 45)
The terminal must always be operated together with the extension cable, otherwisefaults may occur in signal transmission.
The handle of the electro-pneumatic manual force control is equipped with a quick-release coupling at its lower end.
42520944.eps
RUN ERROR
F
]gk[55PB-D)lortnoctuohtiw(tinucisaB 0,81
)esohdnaKSD.lcni(nwod/pU 9,2)esohdnaKSDronenrevogdeeps.lkni(nwod/pU 3,5
lortnocrecnalabdaol-1 0,3lortnocrecnalabdaol-2 2,7
)mm0082elbaclacilehdnaeldnah.lcni(lortnocecroflaunaM 7,8tinuleviwshtiwtesegdewepoR 7,0
]gk[011PB-D)lortnoctuohtiw(tinucisaB 0,72
)esohdnaKSD.lcni(nwod/pU 3,3)esohdnaKSDronenrevogdeeps.lkni(nwod/pU 7,5
lortnocrecnalabdaol-1 3,3lortnocrecnalabdaol-2 7,7
)mm0082elbaclacilehdnaeldnah.lcni(lortnocecroflaunaM 5,31tinuleviwshtiwtesegdewepoR 7,0
2033
5944
.p65
/120
503
9
A protective plate is available for the D Grip system (part no. 773 235 44), whichprotects the right-angle plug against damage. The protective plate is galvanized.
Protective plate (option)
For applications in which the load is turned around a vertical axis, a swivel unit isavailable (part no. 773 260 44) which protects the rope and consists of a ropewedge connection and a swivel unit mounted on ball bearings.
42540944.eps
42540844.eps
2033
5944
.p65
/120
503
10
D brake system (on request)
D brake
This system is exclusively used to prevent that the load slowly sinks, if the com-pressed air supply fails completely.
The system is not suitable for actively braking from the working motion.
If the compressed air supply of the rope balancer is switched off or a loss of com-pressed air reduces pressure down to 0 bar, the load will sink after a certain periodof time.
It is possible to prevent this creeping movement of the load by means of the option-al D brake for the D-BP 110.
The D brake system is supplied with 2 bar from an internal separate compressed airsupply. This pressure works against a spring force which is required to mechanical-ly operate a pin engaging with the rope drum, thus preventing that the load sinks inthe case of a loss off compressed air. The D brake system becomes active, whenthe pressure in the supply line decreases down to 0 bar. Therefore it is recom-mended to select the shutoff unit with valve so that active venting of the supply lineto the rope balancer is possible.
In the case of a pressure reduction >0 bar , the D brake system does not becomeactive.
This option is not available for D-BP 55.
42541044.eps
2033
5944
.p65
/120
503
11
Interface to the load handling device
(DK) = DK hook assembly, (B) = Bullard hook assembly (primarily for the US market)
1) only for the quick-release coupling of the DKM-5 control handle of the DKM 1 Manulift.2) Fitting only allowed, if
1. the load handling device is permanently attached and2. has a min. weight of 3.5 kg.
3) Swivel unit and rope socket integrated in the D Grip operating element of the manual force control.
The load handling devices known from the DK range, such as
• load hook
• C hook
• parallel gripper system etc.
are available for the manual force control for connection to the quick-release cou-pling.
The devices can be engaged on the lower side of the handle.
Further load handling devices for the quick-release coupling see technical data ofDKUN.
Ident. no.:
D-BP pneumatic rope balancer (brochure) 213 055 44
Operating instructions Demag rope balancer 214 421 44
Operating instructions Up/down control 214 587 44
Operating instructions 1 load balance control 214 654 44
Operating instructions 2 load balance control 214 627 44
Operating instructions manual force control 214 611 44
Operating instructions DKM 1 214 087 44
Data sheet Load bar for rope balancer 214 196 44
Data sheet Power supply in preparation
Technical data DKUN 202 846 44
Accompanying documents
)1koohdaoL ylbmessakooHgnilleviws
tekcosepoRdeknarc
tinuleviwS
lortnocnwod/pU- )KD(44046628
)244755628 )244062377- )B(44146628
recnalabdaol-1lortnoc
- )KD(44046628
44755628 44062377- )B(44146628
recnalabdaol-2lortnoc
- )KD(44046628
- )B(44146628
lortnocecroflaunaM 44566538 - )3
Demag Cranes & Components GmbH
P.O. Box 67, D-58286 Wetter
Telephone (+49 2335) 92-0, Telefax (+49 2335) 927676
www.demagcranes.com
Prin
ted
in G
erm
any
Reproduction in whole or in part only with prior consent of Demag Cranes & Components GmbH, D-58286 Wetter Subject to change. Not liable for errors or omissions.
Top Related