Structural Design Code Verifier
Quick Support
www.sdcverifier.com 2
Quick Support allows to get
access to your PC by SDC Verifier
specialist. Send your ID to us:
Skype: sdcverifier_helpdesk;
Phone: +31 15 30-10-310;
Email: [email protected]
Quick Support does not require
Installation of Team Viewer
What is SDC Verifier?
www.sdcverifier.com 3
The goal of SDC Verifier is checking structures according to
standards and report generation.
Load combinations: example from Standard
www.sdcverifier.com 4
19 I
nd
ivid
ual lo
ad
s
SDC Verifier implements:
• Individual Loads;
• Load Sets;
• Load Groups;
A lot of loads and
combinations should
be checked according to
standards.
3 L
oad
Gro
up
s
18 L
oad
Sets
Tools
www.sdcverifier.com 5
Panel Finder;
Beam Member Finder;
Complicated Load: Wind and Hydroload;
Rule Based Selector;
Tools. Panel Finder.
www.sdcverifier.com 6
X Y and Z planes
Frames
Decks Longitudinals
Tools. Beam Member Finder.
www.sdcverifier.com 7
Beams Intersection
Helps to define beam length.
Can be used in Beam Buckling
Check and custom checks.
Beam Length Plot
Tools. Complicated loads
www.sdcverifier.com 8
Water level calculation
Hull pressure
Accelerations on tank
content included
Hydroload Wind
Pressure (depend on height)
Rule based Selector
www.sdcverifier.com 9
Always Up to date
Rule Types:
- Materials;
- Properties;
- Groups;
- Coordinate;
- Element Types;
- Element Shapes;
Operations:
- Add;
- Remove;
- Exclude;
- Reselect.
Coordinate Rule
Element Types Rule
Checks
www.sdcverifier.com 10
Fatigue check according to different methods and
standards
Plate Buckling according to ABS and DNV standards;
Custom Checks;
Moment Shear Force Check;
Example: Fatigue Check with mean stress
correction
www.sdcverifier.com 11
For single stresses
Fatigue Allowable Stress Design (Goodman relation)
Combined
Maximum Fatigue Damage
Allowable Stress depends on classification
Element Group 6 more
than 2 millions cycles
K4 welds example
Used by standards as DIN 15018, FEM 1.001, DASt-011, BS7608, AISC LRFD, etc
Fatigue Example
www.sdcverifier.com 12
Allowable Stress vs Kappa Weld class K3 Weld class K0
Pylon Utilization Factor (Smax/Sallow)
Notch group
Plate Buckling Check (ABS, DNV)
www.sdcverifier.com 13
Calculation methods:
Complete Structure Estimate – user define
standard panel dimension for selection. Element
orientation must be x=length y=width;
Single Panel – each panel is defined. Dimensions
are calculated (check by user). Stresses are
translated into panel direction.
No FEM buckling but stress based
(for full ship +1000 buckling modes)
Plate Buckling Example
www.sdcverifier.com 14
OK with plate dimensions 700x1200 Plots and model IHC Dredgers B.V.
Maximum plate dimensions 700x2450 Maximum plate dimensions 700x1200
SDC Verifier is customizable
www.sdcverifier.com 15
If check is missing use custom check
Simple example 1: Static Stress Check
www.sdcverifier.com 16
Equivalent Stress
Utilization Factor
Sallow = Max (Yield, 0.7 * Tensile)
Utilization Factor = Stress / Sallow
www.sdcverifier.com 17
Example 2: AISC Buckling Check
Moment and Shear Force Check
www.sdcverifier.com 18
Shear Force Moment
At section
Completely custom report
www.sdcverifier.com 19
Standard reports
Report Wizard;
Quick selection method for report generation
Report Designer.
Completely customizable method for fine tuning report
including extra text, summary etc.
Completely custom report
www.sdcverifier.com 20
Report Wizard;
Report Designer.
Report Designer – previewer.
Advanced report
Report Wizard – easy
step by step report
Report Generation in Wizard
www.sdcverifier.com 21
Generated Report
First Page
Model Setup
Job Settings
Tables
Plots
Checks
Model Setup Report
www.sdcverifier.com 22
General information Property Table
Fem Load and Constraint
Description
Report Results
www.sdcverifier.com 23
Result Tables
Result Plots
Checks
Tables
www.sdcverifier.com 24
Displacement on nodes. Absolute maximum highlighted
Extreme Stresses
over directions
Extreme values over selections (properties)
Worst Stresses among loads
Sum of applied forces on loads Extreme Location
Plots
www.sdcverifier.com 25
Same plot different Views Same plot different Components
Report Generation in Designer
www.sdcverifier.com 26
Export To Word Print and Preview without Word
Extra Items
Regenerate
part of report
Edit Item
Properties
Move items
(Drag and
Drop)
Edit properties
with context
menu easily
Toolbox with all project items
Re-use of calculation process
www.sdcverifier.com 27
Set in SDC Verifier file:
full calculation settings
Apply all loads, load combinations and load groups
All checks (according to your standard)
Necessary calculation documents
Re-use .sdcv file as template with all above settings
Open as template
www.sdcverifier.com 28
First model (template) New Model
Two models. Same report
Conclusions SDC Verifier the add-on for:
www.sdcverifier.com 29
Verification of structure according to standards
Simple application of complicated loads
Translation of FEM results in (complicated) code checking results
Complete documentation of model and results
Focus on engineering lets SDC Verifier do the bookkeeping
Use 45 days trial to check it yourself (download SDC Verifier on www.sdcverifier.com
and request trial at [email protected]);
Top Related