Technical Bulletin no. FIM /5 /2017
Raised Bed Planter for Kharif Pulse Cultivation in Assam
DIRECTORATE OF RESEARCH (AGRI)
ASSAM AGRICULTURAL UNIVERSITY JORHAT ASSAM 785 013
January 2017
Raised beds are formed by moving soil from the furrows to the area of the bed with a raised bed planter, thus raising its surface level. The furrows serve as irrigation channels, drains and traffic lanes. Changing from flat to bed layouts alters the hydrology of the system and allows greater control of irrigation, better surface drainage and possibly better capture and use of rainfall. The irrigation water moves laterally from the furrow into the bed, and is driven upwards towards the bed surface by evaporation and capillarity, and downwards largely by gravity. The altered hydrology affects nutrient transformations and transport. For example, transport of solutes towards the surface of the beds can create problems such as salinisation of the seed zone and reduced availability of nutrients to the crop. Normally only the top of the bed is planted, in defined rows, but in some situations the furrows or sides of the beds may also be planted. Assam receives very high rainfall during kharif. The kharif pulse cultivation therefore is always risky. There is possibility of poor germination because saturated soil moisture condition and even inundation because of water logging. Raised bed planting will be good strategy for risk reduction for sustainable pulse production in Assam during kharif season by facilitating drainage. A tractor operated raised bed planter will make the planting easier, drudgery less and cheaper
Construction and specification: The machine (Raised Bed Planter) consists of a frame, fertilizer
box, multi-crop sowing attachment, furrow openers, ridger for making beds, leveler and roller type bed shaper. The machine has a trapezoidal hopper and seed metering unit. A suitable furrow opener system is equipped with the machine to place the seeds at the bed at desired depth. The machine conventionally makes two beds each of 67.5 cm base width, 35 cm top width and slanting height of 20 cm. However the width may be adjusted. Power transmissions to the metering unit are through a ground wheel by chain-sprockets
FtrtUiMf be*
feed »t;irltlg Unit
Figure 1: Isometric view of raised bed planter
2
system. The fertilizer box is fitted on the mainframe with cup feed metering mechanism. The power to the seed metering is transmitted from the spiked ground wheel through chain and sprocket and set of bevel gears. The power transmission wheel is fitted with a tensile spring, which helps in avoiding slippage and that subsequently reduce missing rows in unleveled fields. The machine can act as a zero tillage planter when the shaper is removed and tines are spaced on the three bars. Added spacing provided by the 3-bars, eases loose residue-raking problem of the machine. An isomeric view of the planter is shown in Figure 1 and the detail specifications of functional components of the same are given in Table 1.
Table 1: detail specifications of functional components of the machine Particulars Specification Type Tractor operated 6 row on 2-bed Reported field capacity (ha/h) 0.3-34 Source of power (hp) 45 (34 kW) Overall dimensions ( I x W*H) (mm) 2080 x 1870 x 1350 Weight (kg) 270 Shape and size of frame Rectangular (tubular: cross section
50 mm x 50 mm) Size: 2080 mm x 685 mm
Furrower for beds Number 03 Size (length x width) (mm) 600 x 370 Spacing (mm) 730
Furrower openers for seeding Type Shoe edge type Size (mm) 40 No. of tynes 06 Spacing (mm) 150
Drive wheel Location Front-center Size (diameter x width) (mm) 450 x 80 No. of lugs 12 Lug spacing (mm) 90 Lug height (mm) 40 Power transmission Sprocket and chain system
Seed metering Type Fluted roller type
3
Seed metering Type Fluted roller type No. of fluted rollers 06 Size of fluted roller (diameter x length) (mm) 50x45 No. of flutes 10 Size of flutes (L*W) (mm) 45 x 10 Size of seed box (L x W x H) (mm) 1250 x 260 x 200
Fertilizer metering Type Cup feed type No. of cups 10 Diameter of cup roller (mm) 140 Size of fertilizer box (L x W x H) (mm) 1250 x 260 x 200
Leveler's shape and size (length x diameter) (mm) Round pipe section, 1150 x 30 Shaper's shape Trapezoidal section for bed and
triangular for furrow Top width (mm) 340 Base width (mm) 640 Height (mm) 150 Slope (°) 45
Materials of construction Furrower Mid steel (M.S.) flat and sheet Frame MS flat square pipe channel and Seed metering unit Sheet Fluted roller MS sheet and angle Fertilizer metering unit Aluminum compound Box MS sheet and angle Fertilizer metering roller Cast iron Seeding tynes MS flat, sheet and pipe
Experience at AAU: Studies were undertaken to test and evaluate tractor drawn Raised
Bed Planter under AICRP on Farm Implement and Machinery, A A U , Jorhat Center during 2014 & 2015 with concurrent front Line Demonstrations. Green gram (var. Pratap) and Black Gram (var: K U 301) were tested and result compared with manual raised bed planting. Observation on seed placement depth, mean seed spacing ,missing index, multiple index and quality of feed index was determined. Observation on shape of bed was also estimated. Summary results are presented in Table 2
Table 2: Summary results on machine parameters of raised bed planter
Particulars Manual raised bed Raised Bed Planter planting Green gram Black Gram Green gram Black Gram
Seed placement depth, mm 28 26 46 43 Mean seed spacing, mm 92 89 86 89 Missing index 1.5 1.2 18 12 Multiple index 5 4 12 16 Quality of feed index 93.5 94.8 70 72
= ] > > / N
Where N is the total number o f spacing measured ; x i is the distance between seed/plant I and the next seed/plant
Mean seed spacing : Mean seed spacing (S) is the mean of total number of spacing measured. The Miss Index : Missing Index is the percentage of spacings greater than 1.5 times the set spacing ( X ) . M = n l /N , Where, n l = number of spacing > 1.5 X . The multiple Index: Multiple Index (DI) is the percentage of spacings that are less than or equal to half of the set spacing ( X ) , DI = n 2 / N , Where, n 2 = number of spacing < 0.5 X .
The quality of feed index : It is the percentage of spacings that are more than half but not more than 1.5 times the set spacing. Mathematically, Quality of feed index = 100 - (miss index + multiple index)
Table -3: Summery results from experiment conducted at A A U , Jorhat 2 years (2014 & 2015)
Treatment Yield (t/ha) Quality of feed index B:C ratio Green gram Black gram Green gram Black gram Green gram Black gram (var: (var: K U (var: Pratap) (var: K U 301) (var: (var: K U Pratap) 301) Pratap) 301)
Line sowing 0.41 0.46 45.2 45.0 0.89 0.26 Manual raised 1.04 1.15 93.9 94.3 0.59 0.29 bed Raised bed 0.92 1.06 71.4 73.2 2.80 1.61 planter CD at 5 % 0.072 0.097 4.7 4.02 CV 6.52 7.79 5.19 4.31
The experimental results revealed that raised bed planting with tractor operated raised bed planter resulted in significantly better quality of feed index irrespective o f the crop (green gram and black gram).Though manual raised bed planting resulted in higher yield but it is not economically possible. Economically Mechanical raised bed planter outperformed the conventional method with better B : C ratio up to 2.80.
5
The Raised Bed Planter was subjected to front line demonstration across predominantly pulse growing areas of central Assam in association with K V K (Krishi Bigyan Kendra) Nagaon and Sonitpur. The summary result of FLD is shown in Table 4.
Table 4. Summary results o f front line demonstrations
s. No.
Parameters Raised Bed planter
1 Labour requirement, 10-12 man-h/ha 2 Type of soil Sandy loam 3 Effective working width,
mm 2000
4 Working depth, mm adjustable 5 Size of bed (Width & Bed
height) Width 700 mm,Height 220 mm after sowing, reduced to 90 mm at harvest
6 Soil moisture,% db (before testing)
23
7 Type of seeds Black gram (RSR 27 kg/ha), Green gram (RSR 24 kg/ha)
8 Seed rate, kg/ha 32 (Black gram), 23.7 (green gram) 9 Seed to seed distance, cm 4-6 10 Depth of sowing, cm 3-4 11 Field capacity, ha/h 0.38 12 Fuel consumption, 1/ha 1.46 13 Cost of operation, Rs/ha 1418
The technology has provided a much desired solution for growing kharif pulse which otherwise is risky crop because of higher rainfall and subsequent water logging. Based on the experiment, and FLD recommendation on raised bed planting in kharif pulse was approved for the state of Assam which read as "Mechanical seed placement in raised bed having bed width 600-700 mm and bed height 150-220 mm by tractor drawn raised bed planter with either fluted roller type or cell type seed metering is recommended for growing green gram and black gram in Kharif season.
Planting system: Black gram and green gram have similar recommended crop
geometry. The planting may be done in any of the ways as indicated in Table 5.
6
Planting system
Two row planting in raised bed
Table 5: P l an t ing system
Diagram Field condition
v v • Three row planting in raised bed V V
Three row planting in raised bed in control traffic
f f f
Operation of Raised Bed Planter: • Transport: During transport the raised bed planter should be about 40-50
cm above the road. • Fitting the raised bed planter : Use stand accessory and top link for
hitching the planter to tractor. Use position and draft control lever, and adjust top link length of tractor to maintain the planter level.
• After fitting the planter please check o Whether drive wheel is working properly or not o Whether chain gear is in proper setting or not o Whether seed and fertilizer pipes are clean and ready for sowing. • Weather data is very important for operation of raised bed planter for
kharif pulse. Few rainless days makes the operation of the machine easier. • Raised bed planting in controlled traffic set up makes subsequent weeding
and spraying by tractor drawn equipment possible and makes pulse growing easier and cheaper.
• Slightly higher seed rate than the recommended with closer plant spacing reduces weed problem.
Photo: Research and FLD of Raised Bed Planter conducted at Jorhat and different K V K
7
V
January 2017
Published by: Directorate of Research (Agri) Assam Agricultural University Jorhat Assam India 785 013
Prepared based on the research work of AICRP on FIM by: Dr. Pankaj Barua
Principal Investigator AICRP on FIM
Department of Agricultural Engineering Assam Agricultural University Jorhat Assam India 785 013
A cknowledgement: A l l technical staff
Department of Agricultural Engineering Assam Agricultural University Jorhat Assam India 785 013
Published on the basis of research work conducted under AICRP on Farm Implement and Machinery, AAU, Jorhat center funded by Indian Council
of Agricultural Research (ICAR), Government of India, New Delhi
Top Related