Operating Instructions
Swivel Wheel Shooting Cart (Item # 15102)
IMPORTANT: Read and follow these safety and assembly instructions before oper-
ating! If you have any questions concerning assembly or use of this product, call
Rugged Gear at 800-784-4331 or e-mail us at [email protected].
Safety Rules:
WARNING: Failure to follow these warnings and assembly instructions could
result in serious injury or death.
WARNING: Do Not Transport loaded weapons in this cart. WARNING: Immediately discard any plastic wrapping.
WARNING: Maximum weight capacity is 50 lbs. or 22.7 kg.
WARNING: Never use cart if it becomes damaged.
WARNING: Always engage brakes when you stop or when you let go of handle.
WARNING: You may need to re-distribute the load in the Shooting Cart for bal-
ance.
PLEASE DO NOT RETURN PRODUCT TO THE STORE. We appreciate
your purchase of one of our many fine products. While we make every effort to
insure quality control, occasionally problems may occur. For prompt and correct
handling of problems, or answers to questions regarding assembly or safe use of this
product, please call 800-784-4331 or e-mail us at [email protected]. Service will be quicker if you have
this instruction sheet when calling.
Parts List:
Description Qty. Frame assembly 1
Front Wheel 1
Rear Wheels 2
Rear Axle Assembly 1
Tools Required: Adjustable wrench, 7/16” wrench or 7/16”
socket rachet.
1-800-784-4331
www.ruggedgear.com
Cart Assembly Instructions
Unfold Shooting Cart Remove from carton and remove any packaging ma-
terials that may be holding the frame in closed posi-tion. Grasp frame handle and open. Lock both plastic
latches, on sides by sliding down.
Rear Axle and Wheel Assembly Position rear axle assem-
bly over the two lower
vertical tubes and push
until axle assembly locks
into position with the
chrome buttons (buttons
face forward). Slide rear
wheels on to axles and push wire loop on hub towards center and release to lock onto
axle. To remove axle assembly push chrome but-
tons and pull axle assembly off of vertical tubes.
Front Swivel Wheel Assembly Position wheel and tire assembly over
fork tube and push until the chrome but-
tons lock wheel assembly in place. See photo below
left.
Locking Swivel Wheel Certain type of terrain can be negotiated easier with the swiveling feature locked.
To lock the swivel wheel forward, move lever (above front wheel), down and
rearward. To unlock move lever down and forward. See photo below right.
Latches
Wire
Loop
Front
Rear Axle
Assembly
Chrome
Button
Swivel Wheel
Lock Lever
Mounting the Rugged Gear Gun Holders The Gun Holders on your Shooting Cart will accommodate nearly any type of
shotgun. Proper installation of the Gun Holders will insure safe and fully-
protected transport of your firearms. (See “Normal Operation of the Gun Holder
Hook System” for details concerning placement of guns in Gun Holders).
Gun Holders (found inside the hardware kit) are pre-assembled. Remove cap
nuts, nuts and washers from U-Bolt.
Position Main Base and U-Bolt assembly around Shooting Cart frame with U-
Bolt inserted into Base
Install washers, nuts and cap nuts;
tighten securely around frame.
NOTE: Tighten lower U-bolt
nut first to seat U-bolt base.
This will expose additional
threads to properly start upper U-bolt, nut and washer.
Place the gun to be held in the
Hook. Swivel the Hook to de-
sired angle and position.
Tighten all bolts securely.
Repeat with second Gun Holder
on opposite side of Shooting Cart.
Adjustable Handlebar To adjust handlebar, push in on both buttons
at the same time and reposition handlebar to
desired height.
To Engage Rear Brakes Step lightly on the levers next to the rear wheels until the cogs of the brakes
engage the cogs of the wheel. Repeat on the other side. To release brake, lift
levers with your toe.
To clean fabric: If light cleaning is required, use a soft cloth with warm water
and mild soap then air dry. Do not put in washing machine. Do not put in dryer.
DO NOT BLEACH.
To clean frame: Wipe using a soft cloth with warm water and mild soap. Air
dry. DO NOT USE polish or abrasives.
NORMAL OPERATION OF THE
RUGGED GEAR HOOK SYSTEM
Pull back the Velcro® strap of each hook.
The hooks on the Holder can be bent and shaped to tightly fit any gun. For
maximum holding protection, “over-bend” each hook so that it is smaller than the gun to be held, then force the gun into the hooks.
Squeeze hooks tightly against gun and secure Velcro straps.
Verify that guns are held tightly and re-tighten if necessary.
GUARANTEE Rugged Gear products have a 60-day money-back guarantee.
If you are not completely satisfied, return for a full refund.
For more information on other Gun Holders and Shooting accessories, contact:
(800) 784-4331
or (605)356-2491 · Fax (800)784-3268
Elk Point, SD 57025-9702 U. S. A.
e-mail: [email protected]
www.ruggedgear.com
To Close/Fold Shooting Cart Remove all firearms and equipment from shooting
cart. Grasp black plastic latches on frame and pull up.
Using red colored latch on side of frame, lock folded
cart together.
Top Related