Operating Instructions

Swivel Wheel Shooting Cart (Item # 15102)

IMPORTANT: Read and follow these safety and assembly instructions before oper-

ating! If you have any questions concerning assembly or use of this product, call

Rugged Gear at 800-784-4331 or e-mail us at sales@ruggedgear.com.

Safety Rules:

WARNING: Failure to follow these warnings and assembly instructions could

result in serious injury or death.

WARNING: Do Not Transport loaded weapons in this cart. WARNING: Immediately discard any plastic wrapping.

WARNING: Maximum weight capacity is 50 lbs. or 22.7 kg.

WARNING: Never use cart if it becomes damaged.

WARNING: Always engage brakes when you stop or when you let go of handle.

WARNING: You may need to re-distribute the load in the Shooting Cart for bal-

ance.

PLEASE DO NOT RETURN PRODUCT TO THE STORE. We appreciate

your purchase of one of our many fine products. While we make every effort to

insure quality control, occasionally problems may occur. For prompt and correct

handling of problems, or answers to questions regarding assembly or safe use of this

product, please call 800-784-4331 or e-mail us at sales@ruggedgear.com. Service will be quicker if you have

this instruction sheet when calling.

Parts List:

Description Qty. Frame assembly 1

Front Wheel 1

Rear Wheels 2

Rear Axle Assembly 1

Tools Required: Adjustable wrench, 7/16” wrench or 7/16”

socket rachet.

1-800-784-4331

www.ruggedgear.com

Cart Assembly Instructions

Unfold Shooting Cart Remove from carton and remove any packaging ma-

terials that may be holding the frame in closed posi-tion. Grasp frame handle and open. Lock both plastic

latches, on sides by sliding down.

Rear Axle and Wheel Assembly Position rear axle assem-

bly over the two lower

vertical tubes and push

until axle assembly locks

into position with the

chrome buttons (buttons

face forward). Slide rear

wheels on to axles and push wire loop on hub towards center and release to lock onto

axle. To remove axle assembly push chrome but-

tons and pull axle assembly off of vertical tubes.

Front Swivel Wheel Assembly Position wheel and tire assembly over

fork tube and push until the chrome but-

tons lock wheel assembly in place. See photo below

left.

Locking Swivel Wheel Certain type of terrain can be negotiated easier with the swiveling feature locked.

To lock the swivel wheel forward, move lever (above front wheel), down and

rearward. To unlock move lever down and forward. See photo below right.

Latches

Wire

Loop

Front

Rear Axle

Assembly

Chrome

Button

Swivel Wheel

Lock Lever

Mounting the Rugged Gear Gun Holders The Gun Holders on your Shooting Cart will accommodate nearly any type of

shotgun. Proper installation of the Gun Holders will insure safe and fully-

protected transport of your firearms. (See “Normal Operation of the Gun Holder

Hook System” for details concerning placement of guns in Gun Holders).

Gun Holders (found inside the hardware kit) are pre-assembled. Remove cap

nuts, nuts and washers from U-Bolt.

Position Main Base and U-Bolt assembly around Shooting Cart frame with U-

Bolt inserted into Base

Install washers, nuts and cap nuts;

tighten securely around frame.

NOTE: Tighten lower U-bolt

nut first to seat U-bolt base.

This will expose additional

threads to properly start upper U-bolt, nut and washer.

Place the gun to be held in the

Hook. Swivel the Hook to de-

sired angle and position.

Tighten all bolts securely.

Repeat with second Gun Holder

on opposite side of Shooting Cart.

Adjustable Handlebar To adjust handlebar, push in on both buttons

at the same time and reposition handlebar to

desired height.

To Engage Rear Brakes Step lightly on the levers next to the rear wheels until the cogs of the brakes

engage the cogs of the wheel. Repeat on the other side. To release brake, lift

levers with your toe.

To clean fabric: If light cleaning is required, use a soft cloth with warm water

and mild soap then air dry. Do not put in washing machine. Do not put in dryer.

DO NOT BLEACH.

To clean frame: Wipe using a soft cloth with warm water and mild soap. Air

dry. DO NOT USE polish or abrasives.

NORMAL OPERATION OF THE

RUGGED GEAR HOOK SYSTEM

Pull back the Velcro® strap of each hook.

The hooks on the Holder can be bent and shaped to tightly fit any gun. For

maximum holding protection, “over-bend” each hook so that it is smaller than the gun to be held, then force the gun into the hooks.

Squeeze hooks tightly against gun and secure Velcro straps.

Verify that guns are held tightly and re-tighten if necessary.

GUARANTEE Rugged Gear products have a 60-day money-back guarantee.

If you are not completely satisfied, return for a full refund.

For more information on other Gun Holders and Shooting accessories, contact:

(800) 784-4331

or (605)356-2491 · Fax (800)784-3268

Elk Point, SD 57025-9702 U. S. A.

e-mail: sales@ruggedgear.com

www.ruggedgear.com

To Close/Fold Shooting Cart Remove all firearms and equipment from shooting

cart. Grasp black plastic latches on frame and pull up.

Using red colored latch on side of frame, lock folded

cart together.