Download - ITW DeVilbiss Table of Contents - Fluid Air Section.pdf · Order Toll-Free 800-365-7565 2 Govt. Purchase Cards Accepted Spray Guns-Packages-Accessories Our JGHV Standard-Size Maximum

Spray Guns-Packages-AccessoriesMaximum Performer Features and Benefits .................................................................. 2JGHV Standard Size .................................................................................................... 3JGA-HVLP Suction Feed.............................................................................................. 4MSV Mid-Size .............................................................................................................. 5TGHV Detail/Touch-Up ................................................................................................. 6GFG-HVLP Gravity Feed .............................................................................................. 7GTiTMMillennium/Suction Feed ..................................................................................... 8EXL HVLP Pressure Feed Spray Gun........................................................................... 9EXL HVLP Suction Feed Spray Gun ............................................................................. 9EXL HVLP Gravity Feed Gun ...................................................................................... 10EXL SRi HVLP Spray Gun .......................................................................................... 10FinishLine Gravity and Suction Feed .......................................................................... 11MaxTM Ergonomic Max Performer ............................................................................... 12OMXgt Compliant Gravity Feed .................................................................................. 13EGHV Touch-Up ......................................................................................................... 14Air Cap & Tip Selection Chart ................................................................................ 15-16Air Cap Test Kits ........................................................................................................ 17MBC-510 Manual Spray Gun ...................................................................................... 18JGA-Plus Standard Size Manual Spray Gun ............................................................... 19MSA Mid-Size Manual Spray Gun .............................................................................. 20GFG Gravity Feed Manual Spray Gun ........................................................................ 21EGA Touch-Up Manual Spray Gun .............................................................................. 22Other Equipment and Accessories ............................................................................. 23Spray Equipment Packages .................................................................................. 24-25Solvent SaversTM Hose/Gun Cleaners ......................................................................... 26Fluid Strainers and Equipment ................................................................................... 26

Tanks and CupsQMG Galvanized and QMS Stainless Steel Tanks ................................................. 27-29Tank Accessories .................................................................................................. 30-31Pressure and Suction Feed Cups ............................................................................... 32KB Series Pressure Feed Cups ................................................................................. 33

Clean Air Filtration-AccessoriesCentrifugal Filter-Regulator Units ........................................................................... 34-35Coalescer Filter-Regulator Units ................................................................................. 36Three-Stage Desiccant Unit ........................................................................................ 38Whirl-Wind In-Line Filter ............................................................................................. 39Air Regulators ............................................................................................................ 39Air Control Accessories .............................................................................................. 40Air VizorTM ......................................................................................................... 41-42

Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted

ITW DeVilbiss Table of Contents

1


Spray Guns-Packages-Accessories

Maximum Performer Features and BenefitsDurability

300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harsh,self-etching primers.

• Dual-seal fluid inlet assures apositive seal.

Drop forged aluminum gun bodiesare strong, durable and lightweight.

Lightweight and precision-balanced for operator comfort.

• Maximum Performer sprayguns are sized to fit both theoperator and the application,with standard-size, mid-sizeand detail/ touch-up models.

2

8

7

9

10

Maintenance• Simple, straightforward design for

easy care and maintenance.

• Economical replacement parts areavailable and easy to install.

64

10

8

13

9

72

5

3

5

6

41Replaceable anodized aluminumbaffle with air cap retaining ringthreads eliminates the need toreplace the gun body shouldthreads become damaged.

Redesigned trigger strike padmakes trigger action smootherand extends air valve life.

• Cartridge-type air valve isdesigned for positive sealingand quick triggering action.

• All gun components have beenlife cycle tested to ensurereliability in productionenvironments.

PerformanceGoldMax™ air caps and specialfluid tip, needle and bafflecombinations provideunparalleled atomization.

• Collectively, MaximumPerformer spray guns canhandle more than 90% of thematerials and coatings beingapplied today, including highersolids materials and higher fluidflows.

Long-life needle packings requirefewer adjustments.

Easy to UseLight trigger action for easyoperation and comfort.

Knurled knobs for easy adjustment of pattern and fluidflow.

1/4" air inlet connects to anystandard compressor system.

Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted2


Our JGHV Standard-Size MaximumPerformer manual spray gun gives youthe best of everything -- the comfortablefit and feel of DeVilbiss’ classic JGAspray gun combined with the hightransfer efficiency and superioratomization of HVLP.

• 300-grade stainless steel fluidpassages for waterbornecompatibility.

Productivity and FinishQuality

The productivity and finish qualityof any Maximum Performer spray gun isdetermined by the air cap and fluid tipcombination.

Technical SpecificationsBody: Drop forged aluminumWeight: 20.8 oz (599 gr)Air Inlet: 1/4” NPS (M)Fluid Inlet: 3/8” NPS (M)Fluid Passages: Stainless steelFeed Type: Pressure feedService Bulletin: SB-2-246Gun Repair Kit: KK-4987-2

Accessories• Remote Cups

Two-quart remote cups are availablein aluminum (KB-555) or stainlesssteel (KB-545-SS).

• Attached CupsOne-quart attached cups are avail-able in aluminum with Teflon®lining (TLC-576) or stainless steel(TSC-591).Note: KK-4980 regulator controlkit is required for use with thesecups and must be ordered separately.

• Additional AccessoriesHose assemblies, air controlregulators, air cap test kits, gun andhose cleaning equipment and otheraccessories also are available.

JGHV Standard-Size Maximum Performer

The versatile JGHV gun delivers a highquality finish with less overspray thanconventional guns.

Ordering Information

The JGHV Standard-Size MaximumPerformer manual spray gun is availablewith the following air cap and fluid tipset-ups, factory assembled for immediatedelivery.

Part No.JGHV-531-28FF* JGHV-531-46FXJGHV-531-28FX* JGHV-531-3-46FF**JGHV-531-33FF* JGHV-531-3-46FX**JGHV-531-33FX* JGHV-531-83DJGHV-531-46FF* JGHV-531-83E*Standard tips and needles are 400-gradestainless steel**Includes 300-grade stainless steel withU.H.M.W. polyethylene seat in fluid tips.

When ordering DeVilbiss spray guns, the partnumber includes information on the specificgun model, air cap and fluid tip you willreceive.

Example: JGHV-531-

Fluid Tip SizeAir Cap Number

Basic Gun Model

Note: JGHV-531-46FF has been tested and verified in U.S.E.P.A. Environmentalverfication program under contract #DAAE30-98-C-1050 with the U.S. Army(TACOM-ARDEC) via EPA Inter-Agency Agreement #DW97936814.See WWW.EPA.GOV/ETV Note: JGHV-531-46FF

NSN#4940-01-315-8352

3



Ordering InformationThe Classic Series JGA-HVLP

suction feed spray gun is availablewith the following air cap and fluidtip set-ups, factory-assembled forimmediate delivery. Standard tipand needle are 400-grade stainlesssteel.

Part No.JGA-510-57D*

JGA-510-57DE*

* Cup not included. Order separately.

When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you will receive.

The JGA-HVLP suction feed spraygun offers easy-to-use suction feedoperation with the high transferefficiency of HVLP. That means youget the flow rates and uniform spraypatterns you want using conventionalsuction feed fluid delivery.

• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.

Technical SpecificationsBody: Drop forged aluminumWeight (Less Cup): 21.4 oz (608 gr)Air Inlet: 1/4" NPS (M)Fluid Inlet: 3/8" NPS (M)Fluid Passages:300 grade stainless steelFeed Type: Suction feedService Bulletin: SB-2-248Gun Repair Kit: KK-4987-2

JGA-HVLP suction feed provides highquality atomization with the hightransfer efficiency of HVLP.

Accessories• One-quart paint cups available in

Teflon®-lined aluminum (TLC-555),aluminum (TGC-545) and stainlesssteel (TSC-595).

• One-pint aluminum cup (TGC-536)is also available.

• Hose assemblies, air controlregulators, gun and hose cleaningequipment and other accessoriesalso are available.


The productivity and finish qualityof any Classic Series spray gun isdetermined by the air cap and fluid tipcombination.

Basic GunModel

Air Cap Number

Fluid Tip Size

Example: JGA-510-

JGA-HVLP Suction FeedClassic Series Spray Gun

Five Easy Ways to Order from Fluid-Air Products Inc.

CALLToll-Free

800-365-7565to order

MAILyour order

12834 Gravois Rd.St. Louis, MO 63127

FAXyour order

314-729-7099

E-MAILyour order

[email protected]

WEBSITEVisit our site

www.fluidair.comand link to

www.gsa.govfor on-line ordering



MSV Mid-Size Maximum PerformerManual HVLP Spray Gun

Our MSV Mid-Size MaximumPerformer spray gun delivers the samehigh transfer efficiency and superiorperformance as the standard-sizedmodel, only in a smaller package.Weighing only 17 ounces, theMid-Size Maximum Performer spraygun is lighter, and it helps reduceoperator fatigue while providingexcellent comfort and control.



TM

Technical SpecificationsBody: Drop forged aluminumWeight: 17 oz (476 gr)Air Inlet: 1/4" NPS (M)Fluid Inlet: 3/8" NPS (M)Fluid Passages: Stainless steelFeed Type: Pressure feedService Bulletin: SB-2-243Gun Repair Kit: KK-4987-2

Accessories• Remote Cups

Two-quart remote cups areavailable in aluminum (KB-555)or stainless steel (KB-545-SS).

• Attached CupsOne-quart attached cups areavailable in aluminum withTeflon® lining (TLC-576) orstainless steel (TSC-591).Note: KK-4980 regulator controlkit is required for use with thesecups and must be orderedseparately.

• Additional AccessoriesHose assemblies, air controlregulators, air cap test kits, gun andhose cleaning equipment and otheraccessories also are available.

* Standard tips and needles are 400-gradestainless steel. 300-grade tips and needles(MSV-531-3) should be used for materialswith pH less than 7.** Includes 300-grade stainless steel withU.H.M.W. polyethylene seat in fluid tip.

When ordering DeVilbiss spray guns,the part number includes informationon the specific gun model, air cap andfluid tip you will receive.

Example: MSV-531-

Air Cap NumberFluid Tip Size

Basic Gun Modelw/400 gr. stainless fluid tip, needle


The productivity and finish quality ofany Maximum Performer spray gun isdetermined by the air cap and fluid tipcombination.

The lightweight MSV spray gun isdesigned for maximum operatorcomfort.

The MSV Mid-Size Maximum Performermanual spray gun is available with thefollowing air cap and fluid tip set-ups,factory assembled for immediate delivery.

Part No.MSV-531-28FF* MSV-531-83DMSV-531-28FX* MSV-531-83EMSV-531-33FF* MSV-531-3-28FF**MSV-531-33FX* MSV-531-3-28FX**MSV-531-46FF* MSV-531-3-46FF**MSV-531-46FX* MSV-531-3-46FX**

5



Technical SpecificationsBody: Drop forged aluminumWeight: 19 oz. (530g) TGHV-530

24.5 oz. (690g) TGHV-635 with 8 oz. cup 22.4 (635g)

with 2.5 oz. cupAir Inlet: 1/4" NPS(M)Fluid Inlet: 3/8" NPS(M) - TGHV-530

1/4" NPS(M) - TGHV-635Fluid Passages: 300-grade stainless steelAir Consumption: 6.7 SCFM @ 10 psi air

capAir Requirements: 35 psi inlet=10 psi

cap pressureService Bulletin: SB-2-192Gun Repair Kit: KK-5048

TGHV Detail/Touch-Up Maximum PerformerManual HVLP Spray Gun

TM

Part No.TGHV-530-Pressure/Suction Feed*TGHV-635-Gravity Feed*

Our versatile, new TGHV Detail/Touch-Up Maximum Performer spraygun offers superior atomization at thetip, combined with the comfort benefitsof a lightweight, pistol-grip design, sideport fluid inlet for gravity, and standardbottom inlet for pressure/suction feed.

Requiring low air cap pressure, ourTGHV spray gun provides the controlneeded for detail, repair, shading andhighlighting operations. Depending onthe type of feed used, an adjustablespray pattern from 5" to less than 1/4"round makes the TGHV ideal forapplications requiring focused spraypatterns, such as automotive OEM spotrepair, final repair, as well as maskspraying in furniture manufacturing,plastic decorating, and otherapplications requiring small definedpatterns or mask spraying.

• Side port gravity feed with smallerfront end for better operatorvisibility to the spray target.


• All TGHV series guns utilizemany of the same high qualitycomponents as DeVilbiss JGA,JGV, MSA, and MSV spray guns.


The productivity and finish qualityof any Maximum Performer spray gunis determined by the air cap and fluidtip combination.

The TGHV Spray Gun is availablein both gravity feed and pressure/suction feed models.

•Model TGHV-530 Pressure/Suction Feed Spray Gun.

•Model TGHV-635 Gravity FeedSpray Gun with Cups (2 1/2 oz.and 8 oz. cups included.)

TGHV Accessories• RemoteCups

Two-quart remote cup is available inaluminum (KB-555) or stainlesssteel (KB-545-SS).

• Gravity Cups2 1/2 oz. (TGHV-407-K10) pkg. of10, 8 oz. (KGP-509-1).

• Additional AccessoriesHose assemblies, air cap test kit, gunand hose cleaning equipment and

other accessories are also available.

Ordering InformationThe TGHV Detail/Touch-Up Maximum

Performer manual spray gun is available inthe following models, factory assembled forimmediate delivery.

TGHV-635 Gravity FeedSupplied with 8 oz.TGHV-415 SS cup

* Standard tips and needles are 300-gradestainless steel (F) .041".



GFG-HVLP Gravity FeedClassic Series Spray Gun

When your application calls forhigher transfer efficiency, but you needmore control of the fluid output than youwould get with a suction feed gun,choose the GFG-HVLP gravity feedspray gun. Combining the quality andperformance of HLVP technology withthe advantages of gravity feed fluidflow, the GFG-HVLP spray gun assuresvirtually every drop in the cup is used,so there’s no waste. Clean-up is quickand simple, too.

With gravity feed, atmosphericpressure and gravity itself force thenewer, higher solids materials into thefluid passage, making the gun moreefficient than suction feed. Less air cappressure is required, too.


• Standard equipment includes 20 oz.nylon cup and booth-mount gunhook.

• Drip check in the cup lid preventsleaks and spills from vent hole.

Productivity and Finish QualityThe productivity and finish quality

of any Classic Series spray gun isdetermined by the air cap and fluid tipcombination.

Ordering InformationClassic Series GFG-HVLP gravity

feed spray guns are available with thefollowing air cap and fluid tip set-ups,factory-assembled for immediatedelivery. A new 20 oz. acetal gravity cupis included. Standard tip and needle are400-grade stainless steel.

Part No.GFG-618-57DFFGFG-618-57DFW

When ordering Devilbiss spray guns, thepart number includes information on thespecific gun mode, air cap and fluid tipyou will receive.

Example: GFG-618

Fluid Tip SizeAir Cap Number

Basic Gun Model(including cup)

Technical SpecificationsBody: Drop forged aluminum

Weight (Gun & Cup): 27 oz (768gr)

Air Inlet: 1/4” NPS (M)

Fluid Inlet: 3/8” BSP (F)

Fluid Passages: 300 grade stainless steel

Feed Type: Gravity feed

Service Bulletin: SB-2-169

Gun Repair Kit: KK-5025

Accessories• 8 oz. nylon cup (KGP-510-1).• 32 oz. aluminum cup (GFC-502).• Workbench gun holder (GH-505)

holds the gun upright to facilitatefilling.

• Hose assemblies, air controlregulators, gun and hose cleaningequipment and other accessoriesalso are available.

For smaller production jobs, GFG-HVLPprovides the quality and performance of HLVPtechnology with the advantages of gravity fluidflow.

7



GTiTM

MillenniumGTiTM

Compliant HVLPSuction Feed

� Precision engineered #2000 gold air cap - meetsexacting performance demands, producing an extremelyfine finish with all materials. Developed in conjunctionwith top American and European automotive paintcompanies to spray the latest materials.

� Optimum atomization for clearcoats and single stagesProduces high gloss finish and minimizes orange peel.Excellent fluid control for applying more film build withfewer passes.

� Lightweight and comfortable. Classic JGA fit and feel,yet lighter weight. Gun body styling changes forimproved comfort

� Easy to clean - Plated gun body is gun washer safe andmaintains its “like new” appearance.

� Quick cleanup and upside-down spraying (with nocup lid leaks) - with E-Z LinerTM disposable cup liners.

� GTi Millennium HVLP Spray Gun includes: 1.3mm,1.4 mm, and 1.5 mm fluid tips; 32 oz. aluminum cup(120175/GFC-502) with push on lid; air adjusting valvewith gauge (180006/HAV-01); air cap cleaning kit, spraylube, fluid filter, gun hook; (9) E-Z Liner disposableliners (190966/OMX-70-K48)

� Waterborne compatible - stainless steel fluid tip andneedle, electroless nickel-plated gun body inside andout.

� Lightweight and comfortable - familiar JGA fit andfeel, yet 24% lighter.

� Accurate, repeatable settings - pointers on fluidand fan controls.

� Virtually maintenance-free! - No gaskets,self-sealing.

� Simple, easy-to-use suction feed operation allowspainters to spray with the method they’re used to.

� GTi suction feed gun includes:TGC one quart-cupAir adjusting valve with gauge.

GTi Compliant Suction FeedOrder No. Fluid Inlet AirModel No. Tip (mm) Pressure Applications

170146 2.0 20-25 psi Base coatsGTI-600S 25-30 psi Low and high solids,

clear coats, singlestages

Test

ed/V

erifie

d ETV

/EPA

See W

WW

.EPA

.GO

V.ETV

GTi Millennium Gravity FeedOrder No. Fluid Inlet AirModel No. Tip (mm) Pressure Applications

170156 1.3 & 1.4 20-25 psi Base coatsGTI-620G 25-30 psi High solids clear coats(includes 1.3 & 1.4 mm and single stagesand 1.5 mm fluid tips)

1.5 20-25 psi Base coats25-30 psi Low solids, clear

coats, single stagesand waterbornes



EXLHVLP Pressure FeedSpray Gun� Precisionengineered patented#2000 air cap - Meetsexacting performancedemands, producing anextremely fine finish withall materials. Developed inconjunction with topAmerican and Europeanpaint companies tospray the latest materials.

� Large Spray Pattern forfast coverage.

� Even distribution ofmaterials for no mottling or striping - Excellent colormatching capabilities

� Lightweight and comfortable - Classic DeVilbiss fit andfeel

� Economical servicing - Air cap, fluid tips and needlesare fully interchangeable and available separately.

� Highly efficient HVLP design - Complies withenvironmental regulation requiring high volume,low pressure. Saves material. Very little overspray.

� Stainless steel fluid tip, needle and fluid inlet adapter.

Technical Specifications

Inlet Air AirModel No. Tip (mm) Cap Applications

EXL-520P-11 1.1 2000 Low to medium solidsUp to 12 oz./min.

EXL-520P-14 1.4 2000 High solidsUp to 12 oz./min.



Specifications30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm airvolume

Anodized fluid passages

EXLHVLP Suction Feed

Spray Gun

� Precision engineered patented#2000 air cap - Meets exactingperformance demands, producing anextremely fine finish with all materi-als. Developed in conjunction withtop American and European paintcompanies to spray the latestmaterials.

� Large Spray Pattern for fastcoverage.

� Even distribution of materials forno mottling or striping - Excellentcolor matching capabilities





Includes: Air Cap Cleaning Kit, Spray Gun Lube


Inlet Air AirModel No. Tip (mm) Cap Applications

EXL-520S-18 1.8 2000 Base coat 20-25 psiinlet pressure

EXL-520S-22 2.2 2000 Low and high solidsclear coats and singlestages 25-30 psiinlet pressure



9



EXLHVLP Gravity Feed

Spray Gun� Precision engineeredpatented #2000 air cap - Meetsexacting performance demands,producing an extremely fine finishwith all materials. Developed inconjunction with top Americanand European paint companies tospray the latest materials.

� Large Spray Pattern for fastcoverage.

� Even distribution of materi-als for no mottling or striping -

Excellent color matching capabilities





� Less time spent on refills - True 1-Liter aluminum cupwith disposable push-on lid

� Quick clean up and upside down spraying (no cupleaks) - with E-Z LinerTM disposable cup liners

Includes: Air Cap Cleaning Kit, Spray Gun Lube




Inlet Air Inlet AirModel No. Tip (mm) Pressure Applications

EXL-620G-15 1.5 20-25 psi Base coat25-30 psi Low solids clear coats

single stagesEXL-620G-18 1.8 20-25 psi High solids and

25-30 psi single stages

EXL-620G-22 2.2 20-25 psi High solids and25-30 psi single stages

DeVilbiss SRiTM

HVLP Spray Gun

Fine Atomization and Spot Repair Versatility

Finally - a spot repair spray gun with the control needed forspot repairs plus the comfort of a full-size spray gun. TheDeVilbiss SRITM is the ultimate spot repair spraygun with the fit and feel of a full size spraygun combined with the pattern range andversatility needed for invisible, top qualityspot repairs.

Maximum Control Means MaximumPerformance� Small gun proportions� Ergonomically styled for operatorcomfort� Full fan and spot patterns for spray

versatility� Full size air and fluid controls� Cheater value for precision air adjustments at

the spray gun.� Single finger trigger adjusts from fine feathering to

fadeouts� Uniform material distribution

Includes:1.0 mm fluid tip or 1.2 mm tip, 4 oz. disposable cup and lid. Wrench(SRi-50), Spray lube (SSL-10)

Specifications:29 psi air inlet pressure delivers 10 psi air cap pressure at 4.5 cfmair volume required. (SRi-5033-205) Air Cap test Kit (orderseparately) Provides consistent setup and regulatory proof of aircap pressure.

*Note: For finer control at lower fluid flows, order the optional .8mm tip and needle separately.


Maximum Air Pressure: 100 psi (7 bar)Gun Body: Anodized AluminumNozzle and Needle: Stainless SteelCup: NylonCup Lid: PolypropyleneAir Inlet Size: Universal 1/4” BSP & NPS (M)Gun Weight: 13.7 oz.Gun Repair Kit: SRi-426

Inlet Air Inlet AirModel No. Tip (mm) Pressure Applications

SRi-628-10 1.0 20-29 psi Spot repairs

SRi-628-1.2 1.2 20-29 psi Panel repairs,Door jambs



FinishLineGravity Feed

FinishLineSuction Feed

� Economically-priced

� Available in conventional or compliant HVLP models

� Durable, high quality construction: High gradedie-case alloy gun body. Stainless steel fluid inlet.Alloyed resins for other components to keep gunweight to a minimum. All materials resistant to solventsand gun-washing fluids.

� Precision engineered to produce well atomized,uniform spray patterns

� Easy-to-use controls: Precise spray pattern and fluidflow adjustment. Patented spray pattern knob hasmarker for repeatable settings from full fan to roundspray.

� Waterborne compatible: Stainless steel fluid inlet andfluid needle, plus alloy resin fluid tip.

� 20-oz. lightweight acetal cup with screw-on lid:Built-in “drip check” helps prevent leaks through lidvent hole.

� Quick clean-up and upside-down spraying with no cupleaks with E-Z linerTM disposable cup liners.

� Includes: 20 oz. acetal cup (514302/FLG-502); 4 E-ZLinerTM disposable cup liners (190966/OMX-70-K48);1.4 mm fluid tip (conventional gun); 1.8 mm and 1.6 mmfluid tips (compliant HVLP gun); air adjusting valvewith gauge (180006/HAV-501)(compliant HVLP gun)

Order No. Type Fluid AirModel No. Tip (mm) Cap Applications

512114 Conventional 1.4 #1 General purpose,FLG-611-114 light to heavy

viscosity materials

512318 Compliant 1.8/1.6* #3 General purpose,FLG-631-318 HVLP light to heavy

viscosity materials

* Compliant HVLP models come standard with two sizes of fluid tips

Order No. Type Fluid AirModel No. Tip (mm) Cap Applications

510116 Conventional 1.6 #1 General purpose,FLG-611-114 light to medium

viscosity materials

510-322 Compliant 2.2/1.8* #3 General purpose,FLG-622-322 HVLP light to medium

viscosity materials

* Compliant HVLP models come standard with two sizes of fluid tips

� Economically-priced

� Available in conventional or compliant HVLP models

� Durable, high quality construction: High gradedie-case alloy gun body. Stainless steel fluid inlet.Alloyed resins for other components to keep gunweight to a minimum. All materials resistant to solventsand gun-washing fluids.

� Precision engineered to produce well atomized,uniform spray patterns

� Easy-to-use controls: Precise spray pattern and fluidflow adjustment. Patented spray pattern knob hasmarker for repeatable settings from full fan to roundspray.

� Waterborne compatible: Stainless steel fluid inlet andfluid needle, plus alloy resin fluid tip.

� TGC one-quart aluminum “drip-free” suction cup:Two position valve allows operation as a “drip-free”cup or as a conventional suction cup. “Drip-freediaphragm” helps prevent leaks through lid vent hole.

� Includes: TGC one-quart suction feed cup (12001/TGC-545); 1.6 mm fluid tip (conventional gun); 2.2 mmand 1.8 mm fluid tips (compliant HVLP gun); Airadjusting valve with gauge (18006/HAV-501)(compliant HVLP gun.

11



Max™ Ergonomic Maximum PerformerManual HVLP Spray Gun

Our MAX HVLP spray gun combines ergonomic design with DeVilbiss’ exclusive Maximum PerformerTM

atomization technology to help finishing operations achieve a Class A finish using less air. Value priced fortoday’s high production finishing applications, and weighing just 12 oz., the MAX features solvent resistant,engineered resin materials. Designed with the operator in mind, the small grip size and short grip span, atwo-pound trigger pull force and a pneumatic trigger pull of one-pound, are ideal for smaller hands. The MAXfeatures a nylon-lined, flexible fluid hose with swivel air hose connection so finishers can maneuver easily.

Production and Finish QualityThe productivity and finish quality ofany Maximum Performer spray gun isdetermined by the air cap and fluidcombination. Depending on thecombination, the MAX can handleup to 72% solids by volume.

Ordering InformationThe MAX ergonomic spray gun isavailable with the following air cap andfluid tip set-ups, factory assembled forimmediate delivery.MAX-504-46FFP (.055” fluid tip)MAX-504-83EP (.070” fluid tip)MAX-504-46FXP (.042” fluid tip)

Technical SpecificationsBody: Engineered Resins

Weight (Gun & Cup): 12 oz (454gr)

Air Inlet: 1/4” NPS (M)

Fluid Inlet: 3/8” NPS (male)

Fluid Passages: Engineered Resin,

Teflon, Stainless Steel

Air Consumption: 23 SCFM @ 65 psi

inlet (46MP); 23 SCFM @ 65 psi inlet

(83MP)

Air Requirements: 65 psi inlet =

10 psi at air cap


Gun Repair Kit: KK-5054

Accessories• Air Cap Test Kit: Includes air cap

and gauge to demonstrate actualpressure being used at the cap

• KK-5033-46MP: For use with 46 MPair cap only

• KK-5033-83MP: For use with 83 MPair cap only

Hose assemblies, air controls, pressuretanks, cups, gun and hose cleaningequipment and other accessories arealso available



OMXgt Compliant Gravity Feed

• Super performance - 100% gold air cap providesexcellent atomization of low V.O.C. compliantmaterials with less overspray and lessorange peel. Excellent with high solids.

• Complies with environmental regulationsrequiring HVLP.

• Eliminates need for multiple tips and needles -Fluid control valve adjusts from .8mm to 1.8mm

• The ultimate in painter comfort - Lightweight(only 19 oz.) and well-balanced. Top trigger foreasy spraying of horizontal surfaces withoutbending wrist. Light trigger pull -- 2 lbs. vs.competitors’ 5-6 lbs.

• Waterborne-compatible.

• Easy cleanup and identification of spray gun -Disposable black grips on gun; also available inred. Conveniently identifies basecoat orclearcoat gun.

• Quick cleanup and upside-down spraying -(with no cup lid leaks) with E-Z linerTM

disposable cup liners.

• Includes:Air inlet mini-gauge (192012/OMX-148)Air adjusting valve (HAV-500)28-oz Delrin cup (190977/OMX-467)Red grips (192056/OMX-490)Gun holder (190967/OMX-114)(9) E-Z LinerTM disposable cup liners(190966/OMX-70-K48)Fluid tube cleaning brush (190976/OMX-465)Free instructional video with warranty cardreturn

• Specifications:30 psi air inlet pressure delivers10 psi air cap pressure at 16 cfm air volumerequired.192059 (OMX-5033-100) Air Cap Test Kit

OMXgt Compliant Gravity Feed

*Fluid TipOrder No. Setting Inlet Air

(mm) Pressure Applications

570008 1.4 20-25 psi Base coatsOMX-610 25-30 psi High solids, clear coats

and single stages25-30 psi Waterbornes

1.6 20-25 psi Base coats25-30 Low solids clear coats

and single stages*Adjustable fluid control valve

13



EGHV Touch-Up Maximum Performer

Comfortable and easy-to-use, the EGHV Touch-UpMaximum Performer spray gun provides precise control forthe most exacting detail and touch-up work. The gun featuresa long tapered fluid needle and a top-mounted trigger, andweighs only 7.5 ounces, making it ideal for hours offatigue-free precision painting.• Fluid delivery by attached suction feed or remote

pressure feed cup.• Knurled knobs for fine adjustment of fluid flow and

spray pattern.

Productivity and Finish QualityThe productivity and finish quality of any Maximum

Performer spray gun is determined by the air cap and fluid tipcombination.

Ordering InformationThe EGHV Touch-UP Maximum Performer manual spray

gun is available with the following air cap and fluid tip setup,factory assembled for immediate delivery.

Part No:EGHV-531-397E*

*All wetted surfaces of EGHV are stainless steel


Body: Drop forged aluminumWeight: 7.5 oz. (210 gr)Air Inlet: 1/4” NPS (M)Fluid Inlet: 1/4” NPS (M)Fluid Passages: Stainless SteelFeed Type: Suction feed

Pressure feedAir Consumption: 4.3 CFM max. @

10 psi cap pressureAir Cap Pressure: 10 psi @ 80 psi inletService Bulletin: SB-2-166Gun Repair Kit: KK-5044

EGHV Accessories• 8 Oz Cup (TGS-503) Solvent-resistant

polyethylene cup is available.• Remote Cups

Two-quart remote cups are available inaluminum (KB-555) or stainless steel(KB-545-SS)

• Additional AccessoriesHose assemblies, air cap test kit, gunand hose cleaning equipment and otheraccessories also are available.

EGHV-532 gun and TGS-503 translucent polyethylenecup provide a precision finish with less overspray.

HVLP Spray Gun



Air Cap & Tip Selection ChartJGHV, MSV and AGXV

Medium solidsenamels, urethanes,solvent and water-borne furnituretopcoats, waterborneautomotive OEMfinishes, corrosionprotective coatings,leather stains, acrylics,epoxies, etc. 22.5 CFM

** Recommended Fluid Tips Shown. Other Sizes Are Available.* Viscosity Cup Reference18 Seconds #4 Ford = 22 Seconds ZAHN #222 Seconds #4 Ford = 24 Seconds ZAHN #228 Seconds #4 Ford = 30 Seconds ZAHN #2

Up To12 oz./min.

11"

18.0 CFM

FX (.042")

Most common, lowsolids coatings, i.e.enamels, lacquers,stains, sealers, primers,waterborne adhesives,etc.

Low solids automotivefinishes, enamels,lacquers, stains,sealers, etc. 9" FX (.042")

18.75 CFMUp to

12 oz./min.

12-16 oz./min.

11" FF (.055")

Medium-high solidsenamels, urethanes,low VOC waterbornefurniture topcoats,porcelain enamel,corrosion protectivecoatings, acrylics,epoxies, etc.,architectural andindustrial maintenancecoatings.

26.0 CFM

Low solids, up to25% solids byvolume

Up to 24 seconds,#4 Ford cup

Low solids up to25% solids byvolume


Low-medium solids,up to 50% solids byvolume


Medium-high solids,up to 72% solids byvolume

Over 28 seconds,#4 Ford cup

#46 MP

JGHV-101-46MP

#83 MP

JGHV-101-83MP

TYPICALCOATINGSUSED WITH

*TYPICALSOLIDS BYVOLUME

VISCOSITIES

AIR CAPMODEL NO.

PART NO.

AIRVOLUME(AT 10 psiAIR CAP

PRESSURE)

TYPICALFLUIDFLOWRATES

#28

JGHV-101-28

#33A

JGHV-101-33A

** RECOM-MENDED

FLUIDTIPS

PATTERNSIZE

Over16 oz./min.

13" E (.070") orD (.086")

15



Detail, touch-upenamels, lacquers,etc.

TYPICALSOLIDS BYVOLUME

VISCOSITIES

Low solids,up to 25%solids byvolume

Up to 24seconds,#4 Ford cup 4.3 CFM

F (.041")

Air Cap & Tip Selection ChartEGHV and TGHV

TYPICALCOATINGSUSED WITH

AIRVOLUME(AT 10 psiAIR CAP

PRESSURE)

TYPICALFLUIDFLOWRATES

#395HV

EGHV-439397HV

RECOM-MENDED

FLUIDTIP

* PATTERNSIZE

Detail, touch-upenamels, lacquers,etc.

Low solids,up to 25%solids byvolume

Up to 24seconds,#4 Ford cup 6.7 CFM

F (.041")#90HV

CV-39-90HV

* Spray pattern size dependent upon type of feed, material viscosity, and air cap pressure.

AIR CAPMODEL NO.

PART NO.

Up to4"

Up to5"

Up to 1-1/2 oz./min.

Up to 4 oz./min.


CALLToll-Free

800-365-7565to order

MAILyour order


FAXyour order

314-729-7099

E-MAILyour order

[email protected]






Air Cap Test Kits*

• KK-5033-83-MP Air Cap Test Kit –Includes air cap and gauge, for usewith #83MP air caps only.

• KK-5033-90-HV Air Cap Test Kit –Includes air cap, gauge and ring, foruse with #90HV air caps only.

*Air cap test kits may be required by some airquality agencies. These kits are supplied with aspecial air cap and test gauge to demonstrateactual pressure being used at the cap since itwill vary depending on hose length between theair regulator and gun. This kit can be used as aquality control device for consistent sprayingeach day. The cap kit should not be used whenfinishes are being applied.

Fluid Tips and Needles

• KK-5034 Air Cap Test Kit –Includesair cap and gauge, for use with#397HV air caps only.

• KK-5033-28 Air Cap Test Kit –Includes air cap and gauge, for usewith #28 air caps only.

• KK-5033-33A Air Cap Test Kit –Includes air cap and gauge, for usewith #33 or #33A air caps only.

• KK-5033-46-MP Air Cap Test Kit –Includes air cap and gauge, for usewith #46MP air caps only.

ORDER TIPNUMBER ON FLUID TIP AND NEEDLE SET

For JGHV and MSVAV-2115-FF, FX JGA-4040-FF, FX*AV-2120-D, E, FF, FX JGA-4045-D, E, FF, FX*AV-4915-FF, FX JGA-4056-FF, FX**AV-4920-FF, FX JGA-4051-FF, FX**

For AGXVAV-2115-FF, FX AGX-4402-FF, FX*AV-2120-D, E AGX-4483-D,E*AV-2120-FF, FX AGX-4600-FF, FX*AV-4915-E, FF, FX AGX-4300-E, FF, FX**AV-4920-FF, FX AGX-4613-FF, FX**

For EGHVEGA-60-F EGA-4000-F*

For TGHVCV-30-F-HV TGHV-4000-F***

* 400-grade stainless steel (lapped).** 300-grade stainless steel with U.H.M.W. polyethylene seat in fluid tip (matched set).*** 300-grade stainless steel (lapped).

17



Combining a drop forged aluminumbody with a forged removable sprayhead, the MBC-510 spray gun is idealfor applications that require maximumoutput and quick changeovers.

• Removable spray head allows forreduced downtime on nozzlecombination changeovers.

• MBC spray guns have nickel-platedbrass fluid passages and 400-gradestainless steel fluid tip and needle.


The productivity and finish qualityof any DeVilbiss conventional airspray gun is determined by the air capand fluid tip combination.

Ordering InformationThe MBC-510 manual air spray gun

is available with the following air capand fluid tip set-ups, factory-assembledfor immediate delivery. However, theseare only the most popular set-ups – forother air cap and tip combinations thatcan be ordered separately.

Part No.MBC-510-30EXMBC-510-58EXMBC-510-62HDACMBC-510-64HDDMBC-510-69HDDMBC-510-704EMBC-510-704FF

MBC-510-704FXMBC-510-765EMBC-510-765FFMBC-510-765FXMBC-510-78EMBC-510-797EMBC-510-797FF

Basic Gun ModelAir Cap Number

Example: MBC-510-

MBC-510 Manual Spray GunWith Removable-Head

These guns with fluid tip and needlecan be ordered separately without aircap and retaining ring:

Part No.MBC-510-ACMBC-510-DMBC-510-E

The stainless steel fluid tip has aspecially designed composite fluidseat insert to extend service life andprevent leakage. The gun alsofeatures a Delrin® air cap andretaining ring, along with aremovable spray head for easycleaning.


Body: Drop forged aluminumWeight: 23.6 oz. (661 gr) withair cap and ringAir Inlet: 100 psi max, 1/4" NPS

(M)Fluid Inlet: 100 psi max, 3/8" NPS

(M)Fluid Passages: Nickel-plated brassWetted Parts: 300 and 400-grade

stainless steelComposite Nickel-plated brass

Feed Type: Pressure feedService Bulletin: SB-2-303Gun Repair Kit: KK-4058-1

MBC-510-EXMBC-510-FFMBC-510-FX

Fluid Tip Size

When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you willreceive.


Body: Drop forged aluminumWeight: 27 oz. (756 gr) with air

cap and ringAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 100 psi max, 3/8" NPS(M)Fluid Passages: Nickel-plated brassWetted Parts: Nickel-plated brass

400-grade stainless steelFeed Type: Pressure feed

Suction feedService Bulletin: SB-2-301Gun Repair Kit: KK-4058-1

Accessories• Hose assemblies, air control, pressure

tanks, cups, gun and hose cleaningequipment and other accessories areavailable.

Manual Spray Gun

MBC-Zinc™

Engineered for the trouble-freeapplication of zinc-rich primers, theMBC-Zinc spray gun eliminates leakyfluid tips and zinc-plated air caps.



JGA-Plus Standard SizeManual Spray Gun

* Models include 400-grade stainlesssteel tips and needles.** Models include “premium”300-grade stainless steel tip withU.H.M.W. polyethylene insert (needleseat) and 300-grade stainless steelneedle.

When ordering DeVilbiss spray guns,the part number includes informationon the specific gun model, air cap andfluid tip you will receive.

• Maximum 8 oz./min. fluid flow.• Lower solids coatings.• Medium to high V.O.C. coatings

(4.0-5.0 lbs./gal.).• Smaller compressors - 3 h.p. is

usually sufficient.• Limited air supply - requires only

11 CFM at 10 PSI air cappressure.

• Class “B” finish qualityrequirements.

JGA-HVLP and MSA-HVLP Application GuideThe economical way to convert

DeVilbiss conventional air spray gunsto Classic Series HVLP performanceby using a conversion kit. Simple toconvert for on-site retrofit.

JGA/MSA-TEK offers a simpleconversion to HVLP pressure feed by

changing the air cap, baffle and bafflegasket.

Setting industry standards forhigh-production performance, theJGA-Plus standard-size manual spraygun also offers the comfortable fit andfeel operators prefer. An economicaloption for waterborne and solvent-based material applications, theJGA-Plus stainless steel air spray gundelivers the quality results you needfor tough applications.



The productivity and finish quality ofany DeVilbiss conventional air spraygun is determined by the air cap andfluid tip combination.

Ordering InformationThe JGA-Plus standard-size spray gun

is available with the following air capand fluid tip set-ups, factory-assembledfor immediate delivery. However, theseare only the most popular set-ups – forother air cap and tip combinations thatcan be ordered separately.

Part No.JGA-510-30EXJGA-510-90EXJGA-510-704EJGA-510-704FFJGA-510-704FXJGA-510-705FFJGA-510-705FX

These guns with fluid tipand needle can be orderedseparately without air capand retaining ring:

Part No.JGA-510-D* JGA-510-FX*JGA-510-E* JGA-510-3-FF**JGA-510-EX* JGA-510-3-FX**JGA-510-FF*

JGA-510-765EJGA-510-765FFJGA-510-765FXJGA-510-797EJGA-510-797FFJGA-510-80EX

Example: JGA-510-


Fluid Tip Size

Technical SpecificationsBody: Drop forged aluminumWeight: 21.6 oz. (613 gr) with air

cap and ringAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 100 psi max, 3/8" NPS (M)Fluid Passages: 300-grade stainless steelFeed Type: Pressure feed,

Suction feed (EX)Service Bulletin: SB-2-252Gun Repair Kit: KK-4987-2

Accessories

• Hose assemblies, air control,pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.

• For optional tip and needle sets.

19




Body: Drop forged aluminum Weight:

18.4 oz. (515 gr)

Air Inlet: 100 psi max, 1/4" NPS (M)

Fluid Inlet: 150 psi max, 3/8" NPS (M)

Fluid Passages: 300-grade stainless steel

Wetted Parts: 300 and 400-grade

stainless steel, hardened alloy

Feed Type: Pressure feed


Gun Repair Kit: KK-4987-2

Designed to help reduce operatorfatigue while offering excellentcomfort and control, the MSA midsizespray gun is lighter and more compactthan our standard-size JGA gun. Thatmeans you get the same quality andhigh-efficiency performance providedby our JGA-Plus spray gun, in asmaller model that weighs only 17ounces.


• Air caps and replacement parts areinterchangeable with JGA sprayguns (the air inlet fitting is the onlyexception).


The productivity and finish qualityof any DeVilbiss conventional airspray gun are determined by the aircap and fluid tip combination.

Ordering InformationThe MSA midsize spray gun is

available with the following air cap andfluid tip set-ups, factory-assembled forimmediate delivery. However, these areonly the most popular set-ups – for otherair cap and tip combinations that can beordered separately.

Part No.MSA-510-35LEMSA-510-35LFFMSA-510-35LFXMSA-510-704LE

Decorator Spray GunMSA-510-DEC

The MSA-510-DEC decorator spraygun features a spatter cap to createdecorative textured finishes.

Can be converted to HVLP.

These guns with fluid tip and needlecan be ordered separately without aircap and retaining ring:

Part No.MSA-510-E*MSA-510-EX*MSA-510-FF*MSA-510-FX*

MSA-510-3-E**MSA-510-3-FF**MSA-510-3-FX**

MSA-510-704LFFMSA-510-704LFXMSA-510-797LEMSA-510-797LFF

* Models include 400-gradestainless steel tips and needles.** Models include “premium”300-grade stainless steel tip withU.H.M.W. polyethylene insert(needle seat) and 300-gradestainless steel needle.

When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gunmodel, air cap and fluid tip youwill receive.

Technical SpecificationsBody: Drop forged aluminum

Weight: 17 oz. (476 gr)

Air Inlet: 100 psi max, 1/4" NPS (M)

Fluid Inlet: 100 psi max, 3/8" NPS (M)

Fluid Passages: 300-grade stainless steel

Feed Type: Pressure feed

Suction feed


Gun Repair Kit: KK-4987-2

Accessories• Hose assemblies, air control,

pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.

• For optional tip and needle sets.

Example: MSA-510-


Fluid Tip Size

MSA Mid-Size Manual Spray Gun



Combining the advantages ofgravity feed fluid delivery withadvanced quality and performance, theGFG-617 conventional air spray gunoffers high transfer efficiency forsmall applications that require full,uniform coverage. Fitted with atop-mounted gravity feed cup thatmakes filling simple and quick, theGFG-617 spray gun uses virtuallyevery drop of paint in the cup, evenwhen working with very smallamounts of material.

• 300-grade stainless steel fluidpassages offer waterborne.

compatibility, corrosion resistanceand protection from harshself-etching primers.

• Standard equipment includes a20 ounce acetal cup and

booth-mount gun hook.

• Drip check in the cup lid virtuallyeliminates leaks and spills from thevent hole.


The productivity and finish qualityof any DeVilbiss conventional airspray gun is determined by the air capand fluid tip combination.

Ordering InformationThe GFG-617 gravity feed spray

gun is available with the following aircap and fluid tip set-ups,factory-assembled for immediatedelivery.

Part No.GFG-618-80FWGFG-618-90FFGFG-618-90FW

GFG Gravity Feed Manual Spray Gun

When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you will receive.

Accessories• 8 oz. nylon cup (KGP-509-1).• 32 oz. aluminum cup (GFC-502).• Hose assemblies, air control, gun and

hose cleaning equipment and otheraccessories are also available.

Basic Gun Model(including cup)

Air Cap Number

Fluid Tip Size

Example: GFG-618-

Technical SpecificationsBody: Drop forged aluminumWeight: 27.5 oz. (770 gr) with

paint cupAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 3/8" BSP (F)Wetted Parts: 300 and 400-grade

stainless steelFeed Type: Gravity feedService Bulletin: SB-2-179Gun Repair Kit: KK-5025

Supplied with a32 oz. aluminum cup

21



EGA Touch-Up Manual Spray Gun

The gun of choice for touch-up,shading, edging and detail decorating,the EGA touch-up gun providesprecise control for any type of delicatespray finishing applications. Designedfor external mixing applications, thegun features a forefinger trigger toenhance operator control, and a longneedle taper to make detail work easy.

• Equipped with stainless steel tipand needle.

• Knurled knobs allow fine sprayadjustments for fluid and patterncontrol.


The productivity and finish qualityof any DeVilbiss conventional airspray gun is determined by the air capand fluid tip combination. Body: Drop forged aluminum

Weight: 7 oz. (196 gr) with air capand ring

Air Inlet: 1/4" NPS (M)Fluid Inlet: 1/4" NPS (M)Wetted Parts: Aluminum 400-grade

stainless steelFeed Type: Pressure feed

Suction feedService Bulletin: SB-2-163Gun Repair Kit: KK-5044

Accessories• Hose assemblies, air control,

pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.

Note: EGA-503 model replacesEGA-502.


Fluid Tip Size

Example: EGA-503-

Ordering InformationThe EGA touch-up gun is available with

the following air cap and fluid tip set-ups,factory-assembled for immediate delivery.

Part No.EGA-503-390F

When ordering DeVilbiss spray guns, thepart number includes information on thespecific gun model, air cap and fluid tip youwill receive.




Other Equipment and Accessories

Spray Gun LubeSSL-10-K12

Specially formulated spray gun lubeimproves performance and extends thelife of spray equipment. Contains nosilicones or petroleum distillates tocontaminate paint and coatings. Caseof 12 (2-oz.) bottles. Not for use withair tools and high RPM equipment.

Spray Gun Wrench

WR-103

Versatile tool fits fluid and air hoseconnections, as well as adapters andpacking nuts.

JGA Gun Fluid TubeJGA-444

Handy tube combines the fluid andair hoses at the gun handle to preventtwisted lines and keep hoses fromdragging over work. 3/8” NPS thread.

Disposable Spray Gun CoversSave money by reducing cleaning

time and maintenance with thesecovers that also limit operatorexposure to overspray.GC-100-K4 (pkg. of 4)GC-100-K48 (pkg. of 48)

PART NO. MALE MALE FEMALE

AD-404 – 1/4" NPS 3/8" NPSP-H-4105 – 3/8" NPS 1/4" NPSH-1766 1/8" NPT 1/4" NPS –H-2008 1/4" NPT 1/4" NPS –AD-31 1/4" NPS 1/4" NPS –AD-26 1/4" NPS 3/8" NPS –H-1580 1/4" NPT 3/8" NPS –H-1446 3/8" NPS 3/8" NPS –AD-11 3/8" NPS 3/8" NPT –

Cleaning BrushesFor cleaning the threads and recesses of

the gun body.3/8" dia. brush: 42884-214-K5 (pkg. of 5)5/8" dia. brush: 42884-215-K10 (pkg. of 10)

Thread AdapterThread adapters provide the correct

hook-up for spray guns, hoses, tanksand other spray equipment. Theywork with most standard threadapplications.

23



Spray Equipment

JGHV-531-46FF (.055)DeVilbiss MAXIMUM PERFORMER HVLP spray gun, medium solids,enamels, top coats, Aerospace, automotive OEM finishes, corrosionprotective coatings, acrylics, epoxies up to 50% solids (12-16 oz.min./28 seconds #4 Ford). Stainless Steel fluid passages and stainless steeltip and needle with 46MP air cap, maximum 11” pattern.

Maximum Performer HVLP spray guns also meet operationalrequirements of California South Coast Air Quality ManagementDistrict and other air quality authorities. DeVilbiss HVLP spray gunsare protected by Patents 5,344,078, 5,209,405 & 5,090,623.

KK-4987-2 Repair Kit. Used on JGHV, MSV, MSA and JGAspray guns

KB-555 - 2 quart aluminum remote pressure cup

KB-545-SS - 2 quart Stainless Steel remote pressure cup

TLC-576 - 1 quart aluminum pressure cup (for attached use)TSC-591 - 1 quart Stainless Steel cup (for attached use)

(must use KK-4980 regulator, purchase separately)

QMGT-5223 - 2 gallon ASME galvanized pressure tank, doubleregulation, agitator and air motor

QMST-5223 - 2 gallon ASME stainless steel pressure tank, doubleregulation, agitator and air motor

KB-4006 - 6 ft. hose sets (air and fluid) with fittings for use withremote KB cups

HA-5825 - 3/8” x 25’ I.D. air hose assembly with fittings

HA-7325 - 3/8” x 25’ I.D. fluid hose assembly with fittings

JGHV Spray Gun

KB Cup

TLC Cup &Regulator

QMGT/QMSTPressure Tank



FLHVLP-1 Outfit Consists of:(1) JGHV-531-46FF spray gun of choice(1) KB-555 2 quart aluminum remote pressure cup(1) KB-4004 6 ft. hose set with fittings

FLHVLP-2 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-545-SS 2 quart Stainless Steel remote pressure

cup(1) KB-4004 6 ft. hose set with fittings

**FLHVLP-3 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-555 2 quart aluminum remote pressure cup(1) KB-4006 6 ft. hose set with fittings

FLHVLP-4 OutfitConsists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-545-SS 2 quart Stainless Steel remote pressure

cup(1) KB-4004 4 ft. hose set with fittings

** 4940-01-363-6937-FLHVLP-613 Outfit same asFLHVLP-3 different cup

FLHVLP-5 Outfit Consists of:(1) QMGT 2 gallon galvanized ASME pressure tank(1) Double regulation(1) Air Motor and agitator(1) Disposable liner(1) JGHV-531-46 FF HVLP spray gun of choice25 ft. of air hose with fittings25 ft. of fluid hose with fittings

FLHVLP-6 Outfit Consists of:(1) QMST 2 gallon stainless steel ASME pressure tank(1) Double regulation(1) Air Motor and agitator(1) Disposable liner(1) JGHV-531-46 FF HVLP spray gun of choice25 ft. of air hose with fittings25 ft. of fluid hose with fittings

*FLHVLP-7 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun(1) TLC-576 attached 1 quart pressure cup(1) KK-4980 pressure regulator

FLHVLP-8 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun(1) TSC-591 Stainless Steel attached pressure cup(1) KK-4980 pressure regulator

All outfits may be modified to suit your needs.Other model HVLP spray guns and

ASME pressure tanks available.

* 4940-01-363-6938 - FLHVLP-605 Outfit same asFLHVLP-7

Note: Model JGHV-531-46FF tested/verified ETV/EPA.See WWW.EPA.GOV/ETV

Spray Equipment Packages(fully assembled)

25



Fluid Strainers and Equipment

Solvent SaversTM Hose / Gun CleanersSimple, easy-to-use cleaners speed up

equipment cleaning and save solvent(up to 86% savings!), which reducesV.O.C. emissions. Operate withcompressed air. Provide finely atomizedblast of solvent traveling through fluid

passages of spray guns, hoses, etc.Metering permits varying air/solventmix. Equipped with safety valve. 1/4"NPS (M) air and 3/8" NPS (M) fluidconnections.

Solvent Savers™ Hose/Gun CleanersSHIP WT. MAX. WORKING MATERIAL CONSTRUCTION

PART NO. COMPUTER NO. CAPACITY (LBS.) PRESSURE (IN CONTACT W/FLUID)

*HD-503 180037 2 qt. 5 50 psi Aluminum, nickel plated brass,

Teflon and Thiokol gasket

*QMGZ-5200 2 gal 42 110 psi Galvanized steel, aluminum,

nickel plated brass, Teflon &

Thiokol gaskets, polyethylene

tank liner

QMSZ-5200 2 gal. 38 110 psi 300 grade stainless steel, nickel

plated brass, Teflon & Thiokol

gaskets, polyethylene tank liner

*Note: Not suitable for use with chlorinated solvents, such as 1,1,1 trichloroethylene or methylenechloride. Specify QMSZ type stainless steel when chlorinated solvents are used.

VS-531 VS-532 PLH-MF-6-XX VS-506 VS-534

Fluid Strainers

STRAINER MAX. WORKING INLET OUTLET WETTED SCREEN MESH MICRON

STRAINER TYPE PART NO. PRESSURE THREADS THREADS PARTS PART NO. SIZE SIZE

Gun Mounted StrainersVS-531 300 3/8"NPS(M) 3/8"NPS(F) CS 31144-310-K10 100 149

VS-532 300 3/8"NPS(M) 3/8"NPS(F) PB VS-58-K10 100 149Swivel

In-Line StrainerVS-534 300 3/8"NPS(F) 3/8"NPS(M) SS VS-58-K10 100 149

Swivel

SS = Stainless Steel PB = Plated Brass CS = Carbon Steel


Tanks and Cups

BUILT TO

A.S.M.E.STANDARDS

Approved 2, 5, 10, 15 gallon sizes.Maximum working pressure 110 psi.QMG Tanks contain aluminum and

are not suitable for halogenatedhydrocarbons.

Contact Fluid-Air Products Inc.for more information.

Approved for5, 10 and 15 gallon sizes.

CRN REGISTERED (CANADA)

QMG Galvanized and QMS Stainless SteelTank Specifications

QMG Galvanized Tank ConstructionShell Zinc plated steel, 12 gauge (.105" thick)Lid Zinc plated steel, 3/16" thickAgitator Shaft Zinc plated steelAgitator Paddles Glass filled nylonShaft Seal Thiokol and stainless steelAir Manifold Zinc plated steelFluid Tube Galvanized steelFluid Valve Nickel Plated BrassTop Outlet Fitting Galvanized steelMaximum Working Pressure 110 PSI

Tank Dimensions/CapacitiesQMG Galvanized and QMS Stainless Steel

TANK SIZE ACTUAL CAPACITY (GAL.) INSIDE DIA. INSIDE HT. OVERALL HT.

2-Gal. 2.8 9 1/2" 9 1/2" 13 13/16"5-Gal. 10.8 14" 16" 20 5/16"

10-Gal. 12.7 14" 19 1/16" 23 3/8"15-Gal. 19.8 14" 29 1/16" 33 3/8"

Tank PortsQMG Galvanized and QMS Stainless Steel

Top Fluid Outlet 3/8 NPS(M) Bottom Fluid Outlet Plug 3/4 NPT Air Inlet 1/4 NPS(M) Air Outlet 1/4 NPS(M)

Shipping WeightsQMG Galvanized and QMS Stainless Steel

Tanks TANK CAPACITY SHIP. WT.* (LBS.)

2-Gal. 405-Gal. 85

10-Gal. 9515-Gal. 112*Note: Shipping weights may vary depending on weight ofagitator.

QMS Stainless Steel Tank ConstructionShell 304 stainless steel, 14 gauge (.075" thick)Lid 304 stainless steel, 3/16" thickAgitator Shaft 303 stainless steelAgitator Paddles Glass filled nylonShaft Seal Thiokol and stainless steelAir Manifold Zinc plated steelFluid Tube 316 stainless steelFluid Valve 316 stainless steelTop Outlet Fitting 316 stainless steelMaximum Working Pressure 110 PSI


CALLToll-Free

800-365-7565to order

MAILyour order

12834 GravoisSt. Louis, MO 63127

FAXyour order

314-729-7099

E-MAILyour order

[email protected]




27Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted

Tanks and Cups

QMG Galvanized Tank Specifications

*Direct drive motor included.**Crank may be replaced by optional air motor. See accessories.***Extra sensitive regulator/gauge included.

5 Gallon QMG Galvanized TanksAGITATOR REGULATOR/GAUGE

5 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE

PART NO. PART NO. PART NO. QTY. QTY.

QMGT-5500 NONE QMS-4003 0 1QMGT-5510 NONE QMS-4006 1 1QMGT-5520 NONE QMS-4007 2 2QMGT-5502 QM-142** QMS-4003 0 1QMGT-5512 QM-142** QMS-4006 1 1QMGT-5522 QM-142** QMS-4007 2 2QMGT-5513 QS-5012 QMS-4006 1 1QMGT-5523 QS-5012 QMS-4007 2 2QMGT-5516 QSR-503 QMS-4006 1 1QMGT-5526 QSR-503 QMS-4007 2 2QMGT-5530 NONE QMS-4010*** 1 1QMGT-5533 QS-5012 QMS-4010*** 1 1QMGT-5540 NONE QMS-4022 1 1




QMGT-51500 NONE QMS-4003 0 1QMGT-51510 NONE QMS-4006 1 1QMGT-51520 NONE QMS-4007 2 2QMGT-51502 QM-142** QMS-4003 0 1QMGT-51512 QM-142** QMS-4006 1 1QMGT-51522 QM-142** QMS-4007 2 2QMGT-51513 QS-5012 QMS-4006 1 1QMGT-51523 QS-5012 QMS-4007 2 2QMGT-51516 QSR-503 QMS-4006 1 1QMGT-51526 QSR-503 QMS-4007 2 2

QMGT-51530 NONE QMS-4010*** 1 1QMGT-51533 QS-5012 QMS-4010*** 1 1




QMGT-51000 NONE QMS-4003 0 1QMGT-51010 NONE QMS-4006 1 1QMGT-51020 NONE QMS-4007 2 2QMGT-51002 QM-142** QMS-4003 0 1QMGT-51012 QM-142** QMS-4006 1 1QMGT-51022 QM-142** QMS-4007 2 2QMGT-51013 QS-5012 QMS-4006 1 1QMGT-51023 QS-5012 QMS-4007 2 2QMGT-51016 QSR-503 QMS-4006 1 1QMGT-51026 QSR-503 QMS-4007 2 2QMGT-51030 NONE QMS-4010*** 1 1QMGT-51033 QS-5012 QMS-4010*** 1 1

QMGT-5200 NONE QMS-4030 0 1QMGT-5210 NONE QMS-4006 1 1QMGT-5220 NONE QMS-4007 2 2QMGT-5201 QMG-416* QMS-4003 0 1QMGT-5211 QMG-416* QMS-4006 1 1QMGT-5221 QMG-416* QMS-4007 2 2QMGT-5202 QM-142** QMS-4003 0 1QMGT-5212 QM-142** QMS-4006 1 1QMGT-5222 QM-142** QMS-4007 2 2QMGT-5213 QS-5012 QMS-4006 1 1QMGT-5223 QS-5012 QMS-4007 2 2QMGT-5216 QSR-503 QMS-4006 1 1QMGT-5226 QSR-503 QMS-4007 2 2QMGT-5230 NONE QMS-4010*** 1 1QMGT-5231 QMG-416* QMS-4010*** 1 1

AGITATOR REGULATOR/GAUGE



2 Gallon QMG Galvanized Tanks

Example: QMG T - 5 -


Tank Size2 = 2-Gal. 5 = 5-Gal.10 = 10-Gal. 15 = 15-Gal.

Product Identification

Completely Factory Assembled

T = Top Fluid Outlet

Galvanized

Type of Agitation0 = None 1 = Direct Drive (2-Gal. Only)

2 = Hand 3 = QS-5012 (standard) 6 = QSR-503 (reciprocating)

Type of Regulation0 = None1 = One Regulator2 = Two Regulators

3 = Extra-Sensitive4 = One Regulator, Plated (select 2, 5-Gal. only)5 = Two Regulators, Plated (select 2, 5-Gal. only)


Tanks and Cups

10 Gallon QMS Stainless Steel TanksAGITATOR REGULATOR/GAUGE



QMST-51000 NONE QMS-4003 0 1QMST-51010 NONE QMS-4006 1 1QMST-51020 NONE QMS-4007 2 2QMST-51002 QM-142** QMS-4003 0 1QMST-51012 QM-142** QMS-4006 1 1QMST-51022 QM-142** QMS-4007 2 2QMST-51013 QS-5012 QMS-4006 1 1QMST-51023 QS-5012 QMS-4007 2 2QMST-51016 QSR-503 QMS-4006 1 1QMST-51026 QSR-503 QMS-4007 2 2QMST-51030 NONE QMS-4010*** 1 1QMST-51033 QS-5012 QMS-4010*** 1 1

QMS Stainless Steel Tank Specifications

*Direct drive motor included.**Crank may be replaced by optional air motor. See accessories.***Extra sensitive regulator/gauge included.

Example: QMS T - 5 -


Tank Size2 = 2-Gal. 5 = 5-Gal.10 = 10-Gal. 15 = 15-Gal.

Product Identification

Completely Factory Assembled

T = Top Fluid Outlet

Stainless Steel

Type of Agitation0 = None 1 = Direct Drive (2-Gal. Only)

2 = Hand 3 = QS-5012 (standard) 6 = QSR-503 (reciprocating)

Type of Regulation0 = None1 = One Regulator2 = Two Regulators

3 = Extra-Sensitive4 = One Regulator, Plated (select 2, 5-Gal. only)5 = Two Regulators, Plated (select 2, 5-Gal. only)




QMST-5200 NONE QMS-4003 0 1QMST-5210 NONE QMS-4006 1 1QMST-5220 NONE QMS-4007 2 2QMST-5201 QMS-430* QMS-4003 0 1QMST-5211 QMS-430* QMS-4006 1 1QMST-5221 QMS-430* QMS-4007 2 2QMST-5202 QM-142** QMS-4003 0 1QMST-5212 QM-142** QMS-4006 1 1QMST-5222 QM-142** QMS-4007 2 2QMST-5213 QS-5012 QMS-4006 1 1QMST-5223 QS-5012 QMS-4007 2 2QMST-5216 QSR-503 QMS-4006 1 1QMST-5226 QSR-503 QMS-4007 2 2QMST-5230 NONE QMS-4010*** 1 1QMST-5231 QMS-430* QMS-4010*** 1 1










Tanks and Cups

Tank AccessoriesQMG Galvanized and QMS Stainless Steel

Tank Inserts With HandleStainless steel insert for use inside

tank. Removable insert with handle iseasily portable – eliminates need tocarry entire tank to paint-fill area.Also protects tank and material. (Maybe used in tanks with agitator.) Direct Drive Agitator

Air-powered direct drive agitatorassembly with 1/4 hp air motor anda three-bladed propeller to keepmaterials mixed in suspension, evenhigh solids. Use on two-gallon QMGmodels. Shipping weight 8 lbs.

QMG-416 (for use with QMG)

QMS-430 (for use with QMS)

Paint Drum Agitator DriveQS-5003

For use with paint drums havingbuilt-in agitators. Powerful variablespeed air motor. Requires 5 to 8 CFMof air for 50 RPM of agitator;adjustable from 10 RPM up. Airconnection 1/4" NPS(M). Includescouplings to fit 7/16" and 1/2" agitatorshafts. The mounting adapter fits both1-1/2" and 2" threads. Shippingweight: 15 lbs.

Hand Crank QM-142For manual operation of agitator.

Shipping weight: 1 lb.Dual Fluid Outlet KitAllows two spray guns to be supplied

by a single pressure tank. Shippingweight: 3/4 lb.

QMG-443 (for use with QMG)

QMS-454 (for use with QMS)

Tank Inserts TANK CAPACITY PART NO. SHIP. WT.

5-Gal. QMS-427 10 lbs.

10-Gal. QMR-410 16 lbs.

15-Gal. QM-4245 19 lbs.

Polyethylene LinersSemirigid tank liners of tough,durable, high density polyethylenewith “ANTI-STAT” additive whichminimizes static electricity buildupfrom the friction of shipping andhandling liners. May be reused. (Canbe used with optional agitators.)

Air Motor DriveQS-5012

Standard duty, smooth running withgear reducer, 1/4 hp, 15:1 ratio, 20 to120 RPM. Includes throttling valve,fittings, and hose for connection to airsupply on tank lid. Air consumption:Approximately 6 CFM at 50 RPM.Shipping weight: 11 lbs.

Note: 170°F Max Temperature

Polyethylene Liners TANK CAPACITY PART NO. KIT OF SHIP. WT.

2-Gal. PT-52-K10 10 7 lbs.2-Gal. PT-52-K80 80 29 lbs.5-Gal. PTL-406-K20 20 20 lbs.

10-Gal. PTL-410-K8 8 12 lbs.


Tanks and Cups

Air Regulator Assembly Kits

Part No.

QMS-436One gauge, one regulator. Convertssingle regulation to dual.

QMS-4003One gauge, no regulator. Indicatespressure in tank. Wt: 2 lbs.

QMS-4006One gauge, one regulator. Regulatesand indicates tank pressure. Wt: 4 lbs.

QMS-4007Two gauges, two regulators. Controlstank pressure and atomization airpressure to gun. Wt: 6 lbs.

QMS-4010One extra sensitive gauge, oneextra sensitive regulator. Usewith electrostatic spray or otherapplications requiring extremelysensitive, non-fluctuating, lowpressure control.Wt: 5 lbs. Max. 30 lbs. pressure.

QMS-4022One specially-plated gauge andregulator. Regulates and indicates tankpressure. Wt: 4 lbs.

QMS-4023Two specially-plated gauges andregulators. Controls tank pressure andatomization air pressure to gun.Wt: 6 lbs.

Tank AccessoriesQMG Galvanized and QMS Stainless Steel

Chemical CompatibilityWith Gasket Materials

E: Excellent G: Good C: ConditionalU: Unsatisfactory X: No Test Data

The chemical compatibility shown here is meantfor initial guidance only. Actual concentrationsand conditions greatly affect corrosionresistance.

GASKET MATERIAL

SBR RUBBER TEFLON THIOKOL

Acetone U E C Carbon Tetrachloride U E C Chlorinated Solvents U E C Glycerine E E C Lacquers U E C Linseed Oil U E E Methyl Ethyl Ketone U E E Mineral Oil U E C Tannic Acid G E G Toluene (Toluol) U E G Trichlorethylene U E G Turpentine U E E Varnish U E X *Waterborne Coatings E E E Xylene (Xylol) U E ENote:*Check co-solvent used in waterborne material

for compatibility.

GASKET 2-GAL. 5, 10, AND 15-GAL.

MATERIAL PART NO. PART NO.

SBR Rubber QM-1008

Teflon QMS-52 QMS-51

Thiokol* QMS-80-K2 QM-1458

Optional Agitator Drive AccessoriesReplacement Units. Motor drive or crank must be ordered separately.

STANDARD RECIPROCATING

DESCRIPTION GALVANIZED STAINLESS MOTOR DRIVE MOTOR DRIVE HAND CRANK

PART NO. PART NO. SHIP WT. PART NO. PART NO. PART NO.

2-Gal. Direct Drive Agitator Assembly QMG-416 QMS-430 8 lbs. includes motor* n/a n/a 2-Gal. Hand Agitator less drive motor QMG-417 QMS-431 7 lbs. QS-5012 QSR-503 QM-14 5-Gal. Agitator Assembly less drive motor QMG-418 QMS-432 8 lbs. QS-5012 QSR-503 QM-142 10-Gal. Agitator Assembly less drive motor QMG-419 QMS-433 9 lbs. QS-5012 QSR-503 QM-142 15-Gal. Agitator Assembly less drive motor QMG-420 QMS-434 10 lbs. QS-5012 QSR-503 QM-142

Lid GasketsReplacements / Options

DeVilbiss offers several lid gasketalternatives to be used in place of thestandard Thiokol® gasket. Refer tochemical compatibility with gasketmaterials chart at right. (Note: ThiokolGaskets are standard on all factoryassembled QMG and QMS tank models.)

* 2-gal. direct drive agitator assembly includes standard air motor.

Shipping Weightsfor QMG and QMS Accessories

ADD FOR*AGITATOR/ AGITATOR/

TANK AGITATOR/ QS-5012 QSR-503

CAPACITY CRANK AIR MOTOR AIR MOTOR

2-Gal. 8 lbs. 18 lbs. 22 lbs.5-Gal. 9 lbs. 19 lbs. 23 lbs.

10-Gal. 10 lbs. 20 lbs. 24 lbs.15-Gal. 11 lbs. 21 lbs. 25 lbs. *Example: A 15-gallon tank with optionalQS-5012: shipping weight 112 + 21 lbs. =133 lbs.

*Standard on all factory-assembled QMGand QMS tank models.

Bottom Outlet Conversion KitFittings which allow standard top outlet tank to feed from bottom by removing plug in

bottom port. All wetted parts galvanized steel for QMG models.TANK GALVANIZED STAINLESS STEEL

CAPACITY PART NO. PART NO. SHIP WT.

2-Gal QMG-421 QMS-435 3 lbs. 5, 10, 15-Gal. QMG-428 QMS-443 4 lbs.


Tanks and Cups

Pressure and Suction Feed Cups

Gravity Feed CupsMade of strong, lightweight material

for durability. Features a “dry check”device integral with cup lid to avoidspillage from vent hole.

KGP-509-1 - 8-oz. Cup (Nylon)

GFC-501 - 20-oz. Cup (Delrin)

Polyethylene Suction CupTGS-503

8-oz. cup size. Combines engineeredresin lid with translucent polyethylenecup – liquid level visible. Molded-ingraduations for mixing ratios.Lightweight and easy to clean.Nonstaining. Includes cup closure.Compatible with all solvents. Use withEGA-502, EGHV-530 or any suctionfeed gun with 1/4" NPS threads.

Aluminum Suction CupsAluminum suction cups incorporate a

two-position special lid design – oneas drip-free cup or the other asconventional suction feed cup. Smoothmetal surfaces make cleanup andchanging paint fast and easy. Use withall suction feed spray guns.

TGC-545 - Quart Capacity Suction Cup

TGC-536 - Pint Capacity Suction Cup

Low Pressure Cup for HVLPTLC-576

Aluminum, one-quart, lowpressure cup for HVLP applications.Teflon®-lined for fast, easy cleaning.Solvent-resistant check valve.Requires KK-4980 for cup airregulation. (Order separately)

Teflon®-Lined Suction CupTLC-555

Aluminum, one-quart cup featuringTeflon® lining for fast, easy cleaningand reduced color contamination.Drip-free lid design has two-positionvalve which allows for operation as“drip-free” cup or as conventionalsuction cup. Use with all suction feedspray guns.

Stainless Steel CupsOne-quart cups made from 300

series stainless steel, designed for usewith waterbased materials and exemptsolvents. The .030" wall thicknessmakes it more durable thancompetitive cups, yet still lightweight.And the fluid tube is stainless steel foradded durability and corrosionresistance.

TSC-591 - HVLP Low PressureFeed Cup. Requires KK-4980 for cupair regulation (order separately)

TSC-595 - Suction Feed Cup


Tanks and Cups

For use with both conventional airspray systems and HVLP systems, theKB II series, two-quart cups feature a“pistol grip” carrying handle, and rightor left-handed design for comfort andease of handling. An easy-open lid andwide cup mouth allow for fast fillingand cleanup. KB Series cups alsofeature a solvent resistant check valveand a wide base for greater stability.

KB series cups are ideal for handlingheavier viscosity materials, higher flowrates, as well as low fluid flow rates of10 ounces per minute or less. Fluidpressure range of 2-30 psi. Order air/fluid hose assemblies separately.

KB-4004 - 4-foot hose length.

KB-4006 - 6-foot hose length mostcoating materials and solvents.

Pressure and Suction Feed CupsCOMPLETE CUP CONNECTION APPROX. SHIP

ASSEMBLY THREAD SIZE CUP AND COVER CUP ONLY WT/ COMPLETE

PART NO. CAPACITY MATERIAL FLUID AIR ASSEMBLY PART NO. CUP AND LID

Pressure FeedKB-555 2 qt. Aluminum 3/8"NPS(M) 1/4" NPS(M) — KB-422 3 lbs. 14 oz.

KB-545-SS 2 qt. Stainless Steel 3/8"NPS(M) 1/4" NPS(M) — KB-442 5 lbs. 2 oz.

TSC-591 1 qt. Stainless Steel 3/8"NPS(M) — — TSC-400 20 oz.

TLC-576 1 qt. Aluminum w/Teflon® Lining 3/8"NPS(F) — TLC-401 18 oz.

Suction FeedTGC-536 6 oz. Aluminum 3/8"NPS(F) — — TGC-432 12 oz.

TGC-545 1 qt. Aluminum 3/8"NPS(F) — — KR-428-2 18 oz.

TGS-503 8 oz. Polyethylene 1/4"NPS(F) — TGS-406 3 oz

TLC-555 1 qt. Aluminum w/Teflon® Lining3/8"NPS(F) — TLC-401 18 oz.

TSC-595 1 qt. Stainless Steel 3/8"NPS(M) — — TSC-400 20 oz.

Gravity FeedKGP-509-1 8 oz. Nylon 3/8"BSP(M) — — — 3 oz.

KGP-510-1 20 oz. Delrin 3/8"BSP(M) — — –– 6 oz.* Use with GFG and GFHV guns only.** Order KK-4980 Air Regulator Kit in addition to cup.

KB Series Pressure Feed Cups

Aluminum CupKB-555

DeVilbiss KB Aluminum modelcups are compatible with most coatingmaterials and solvents.

Stainless Steel CupKB-545-SS

DeVilbiss KB Stainless Steelmodel cups are designed for usewith waterbornes, halogenatedhydrocarbons and other corrosivematerials.

KK-5051 Disposable CupLiner Kit includes20 liners, 20 lids and 3 rings

33


Clean Air Filtration-Accessories

CleanAir Centrifugal Filter-Regulator Units

Excellent for eliminating moistureand dirt from an air supply, DeVilbissCleanAir centrifugal units supplycleaner, drier air to each spray gun in asystem. This cleaner air can alsoincrease the life of pneumatic tools.

• Filters out water and oil aerosols anddirt particulates to 5 microns.

• Ideal for most spray applications, airtools and equipment.

• Water droplets collected in the bowlare removed by an automatic drain(standard feature). No need tomanually drain.

Quick-release filter bowl and spin-off5-micron filter element allow one-minutefilter changes without tools. Pressure dropsare minimized by large air inlet and outletand large internal air passages.

HFRL-511

HAF-502 HAF-503 HFRL-508 HFRL-509

• Prevents tampering or unauthorized air regulatoradjustment

• Where 10 PSI max. HVLP air cap pressures isregulated, can prevent noncompliance andpotential fines

• Assures proper atomization and fluid pressure forconsistent spray performance

• Used with DeVilbiss “HAR” type air regulators(some competitive models also)

• Easy to install

HAR-400 REGULATOR LOCKOUT ACCESSORY 3/16” Allen Slot Locknut

Sleeve & LockAssy.

AdjustmentScrew



CleanAir Centrifugal Filter-Regulator Units

Accessories• Mounting Bracket Assembly Kits

For HAF-502 air filter and HFRL-508regulator; order HAF-407.For HAF-503 air filter, and HFRL-509and HFRL-511 regulators, orderHAF-408.

Centrifugal Air Filter UnitsPART NO. HAF-502 HAF-503

Filtering Capacity (micron) 5 5

Flow Rate (CFM) 100 @ 90 psi 150 @ 90 psi

Max. Inlet Pressure (psi) 150 150

Max. Operating Temp. 150oF 150oF

Inlet Port Size 1/2" NPT (F) 3/4" NPT (F)

Outlet Port Size 1/2" NPT (F) 3/4" NPT (F)

Bowl Capacity 17 oz. 34 oz.

Shipping Weight 1 lb. 7 oz. 3 lbs. 1 oz.

Service Bulletin SB-6-146 SB-6-148

Tornado-like swirling action removes moisturewhich collects in the baffled “quiet zone.”The reusable 5-micron filter catches smallerimpurities. Accumulated liquid is carriedaway by the automatic drain.

Airinlet

Centrifugal Filter-Regulator UnitsPART NO. HFRL-508 HFRL-509 HFRL-511

Filtering Capacity (micron) 5 5 5

Flow Rate (CFM) 50+ 80+ 120+

Max. Inlet Pressure (psi) 150 150 150

Regulated Pressure Range (psi) 0 - 125 0 - 125 0 - 125

Max. Operating Temp. 150oF 150oF 150oF

Inlet Port Size 1/2" NPT (F) 3/4" NPT (F) 3/4" NPT (F)

Regulated Outlets (w/ball valve) (1) 1/4" NPS (M) (2) 1/4" NPS (M) (4) 1/4" NPS (M)

Non-Regulated Outlets (w/ball valve) (1) 1/4" NPS (M) (1) 1/4" NPS (M) (1) 1/4" NPS (M)

Bowl Capacity 17 oz. 34 oz. 34 oz.

Air Filter Included HAF-502 HAF-503 HAF-503

Quality Air Regulators/Model (1) HAR-506 (1) HAR-507 (2) HAR-507

Air Gauges (0 - 100 psi) 1 1 2

Air Gauges (0 - 160 psi) 1 1 1

Shipping Weight 9 lbs. 15 lbs. 18 lbs.

Service Bulletin SB-6-146 SB-6-148 SB-6-148

Flexibletubing

Automaticdrain

Quietzone

Baffle

Reversible5-micronfilterTornado

swirl ring

• Filter Element Kits (5-Micronreusable)For HAF-502 air filter and HFRL-508regulator; order HAF-6.For HAF-503 air filter, and HFRL-509and HFRL-511 regulators, order HAF-15.


CALLToll-Free

800-365-7565to order

MAILyour order


FAXyour order

314-729-7099

E-MAILyour order

[email protected]




35



CleanAir Coalescer Filter-Regulator Units

HFRL-513

CleanAir coalescer filters removewater, dirt and oil from the systemdown to .01 micron. DeVilbisscoalescer filter units are designedwith a quick-release bowl andspin-off element for filter changeswithout tools. In addition, a filter-change indicator alerts the operatorwhen the element requires changing.

• Borosilicate glass microfiber filter isengineered for high flow, highefficiency, quick change and lowpressure drop.

• Ideal for most spray applications,especially where oil aerosols maybe a problem.

• Automatic bowl drain and 6' hoseeliminate oil and water buildup(standard feature). No need tomanually drain.

The HAF-508 is the coalescer filteronly. In combination with thecentrifugal filter, there are threechoices – the HAF-509 non-regulatedunit and the two regulated models –HFRL-512 and HFRL-513.

HAF-509 HFRL-512



CleanAir Coalescer Filter-Regulator Units

Accessories• Mounting bracket assembly kit is

available; order HAF-408.

• Centrifugal filter element kit hasreusable 5-micron filter; orderHAF-15.

• Coalescer filter element kit has.01-micron filter; order HAF-38.

Centrifugal-Coalescer Filter UnitsHAF-508 HAF-509

NON-REGULATED MODELS COALESCER* CENTRIFUGAL& COALESCER

Centrifugal Filtering Capacity (micron) 5 5

Coalescer Filtering Capacity (micron) .01 .01

Flow Rate (CFM) 150 @ 90 psi 150 @ 90 psi




Outlet Port Size 3/4" NPT (F) 3/4" NPT (F)


Shipping Weight 3 lbs. 2 oz. 6 lbs. 3 oz.


Pre-filter support fabric prevents mediamigration, increasing element life. Stainlesssteel screens provide fail-safe protection againstaccidental shock loads and high pressure dropsin either direction. Anti re-entrainment barrierprevents liquid carryover, even in shockconditions, and is compatible with mineral andsynthetic lubricants. A – Easy-fit captive O-ring

Coalescer-Filter Regulator UnitsREGULATED MODELS HFRL-512 HFRL-513

Centrifugal Filtering Capacity (micron) 5 5

Coalescer Filtering Capacity (micron) .01 .01

Flow Rate (CFM) 80+ 120+


Regulated Pressure Range (psi) 0 - 125 0 - 125



Regulated Outlets (w/ ball valve) (2) 1/4" NPS (M) (4) 1/4" NPS (M)

Non-Regulated Outlets (w/ ball valve) (1) 1/4" NPS (M) (1) 1/4" NPS (M)


Quality Air Regulators/Model (1) HAR-507 (2) HAR-507

Air Gauges (0 - 100 psi) 1 2

Air Gauges (0 - 160 psi) 1 1

Shipping Weight 18 lbs. 2 oz. 21 lbs. 2 oz.


* HAF-508 coalescer filter should be used in conjunction with a centrifugal type filter to removethe majority of water, oil and dirt, prior to the coalescer filter.

A

B

C

D

E

G

F

B – Corrosion-resistant end capsC – Pre-filter support fabricD – Stainless steel support screensE – Anti re-entrainment barrierF – Borosilicate glass microfiber filter

G – High-strength epoxy sealant

37



CleanAir Three-Stage Desiccant Unit

The three-stage desiccant unitprovides the ultimate in clean dry air.First stage centrifugal filter removesparticulates to 5 microns. Stage twocoalescer filters down to .01 micron.Third stage desiccant removesremaining water vapor to a dew pointof -40oF.

• Ideally suited for low to mediumproduction.

• DAD-500 air-drying system includesthree filtering units, as well as a wallmount bracket and desiccant filterchange indicator.

• Centrifugal and coalescer unitsinclude automatic bowl drain(standard feature). No need tomanually drain.

DAD-500 Desiccant Air Drying SystemDAD-500 HAF-502 HAF-505 HAR-506

AIR DRYING CENTRIFUGAL COALESCER REGULATORDESICCANT SYSTEM UNITS SYSTEM* FILTER ONLY FILTER ONLY** ONLY

Air Inlet 1/2" NPT (F) 1/2" NPT (F) 1/2" NPT (F) 3/8" NPT (F)

Air Outlet 1/2" NPT (F) 1/2" NPT (F) 1/2" NPT (F) 1/4" NPT (F)(3 ea)

Max. Operating Pressure (psi) 150 150 150 150

Replacement Filters/Desiccant DAD-1 HAF-6 HAF-28 —

Service Bulletin SB-6-156 SB-6-146 SB-6-152 SB-6-144

Air Flow Capacity (cfm) 25 100 55 40

DAD-500

* Includes HAF-502, HAF-505 and HAR-506.** Has filter-change indicator to alert operator when element requires changing.


CALLToll-Free

800-365-7565to order

MAILyour order


FAXyour order

314-729-7099

E-MAILyour order

[email protected]






HAF-507-K12 WhirlWind In-Line FilterMAXIMUM

HOUSING OPERATING OPERATING PRESSURE DROP LIQUID SERVICEMATERIAL PACKAGING THREADS PRESSURE TEMPERATURES @ 80 PSI w/ 20 SCFMCONTAMINANT BULLETIN

Solvent-resistant 12 filters 1/4" NSP (M) inlet 125 psi 50oF - 110oF 2 psi 1.5 fl. oz. SI-8-10-1Delrin® plastic per dispenser carton 1/4" NSP (F) inlet

MAX. REGULATED MAX AIR MAX

CAPACITY PRESS.RANGE INLET PRESS. OPERATING DIMENSIONS WEIGHT MAIN AIR INLET MAIN LINE OUTLET REGULATED OUTLETS

MODEL CFM PSI PSI TEMP OF H" X W" LBS. PORT SIZE PORT SIZE PORT SIZE

HAR-501* 15 0 - 20 250 120o 6 x 4-1/2 2-1/4 1 3/8" NPT (F) - - 1 3/8" NPT (F)HAR-535 40 0 - 125 250 120o 4-7/8 x 2-3/8 1-1/8 1 3/8" NPT (F) 1 1/4" NPT (F) 1 3/8" NPT (F)HAR-555 40 0 - 125 250 120o 4-7/8 x 2-3/8 1-1/8 1 3/8" NPT (F) 2,4 1/4" NPT (F) 1 1/2" NPT (F)HAR-507 60 0 - 125 300 120oo 4-7/8 x 3 1-1/2 1 3/8" NPT (F) - - 3 1/4" NPT (F)

WhirlWind In-Line Filter

The WhirlWind disposable in-linefilter attaches to the base of the spraygun or air tool to remove anyremaining water, oil, dirt and rustfrom the air line. This high-quality,high-flow, solvent-resistant air filterhas a very low pressure drop and hasa floating filter that automaticallyadjusts for changing air conditions.

• Air is swirled to trap droplets, thenfiltered to absorb remainingparticulates.

• Multilayer design extends life, so unitlasts up to 40% longer than other filters.

• Perfect for use with HVLP guns,WhirlWind provides 55% more air flowthan other filters.

HAF-507-K12

CleanAir Air RegulatorsHAR-502/505/535/555/556/557

Air RegulatorGeneral purpose regulators for line

takeoff use or as integral regulators onpumps, pressure tanks and other airoperated devices. Require separate trapor filter in air line to remove moistureor dirt.

• Unique three position, non-risingadjusting knob.

• Removable plug and cap.

• All metal body; durable Delrin® capand knob; Buna N diaphragm anddisc.

• Accurate regulator mechanismprovides precision air control.

• Self-relieving design.

• Both main line and regulated outletsavailable from same units.

HAR-501 Air RegulatorExtra Sensitive regulator for use

with precision control on pressure feedtanks or other dead-end applications.Can be used to control atomizationpressure for one spray gun.

• Self-relieving regulator.

• Tough, reinforced Buna N

diaphragm for extended service life.

• 100 mesh stainless steel strainer.

• Removable bottom plug for easyservice.

• Forged brass body and stainless steelor brass internal parts for longservice.

• High ratio of diaphragm surface toorifice area provides stable uniformregulation.

* Extra-sensitive regulator for precise control on pressure tanks and other dead-endapplications.

TM

HAR-505 HAR-501

39



Air Control Accessories

For accurate pressure readings,standard gauges are made fromrust-resistant materials and includeglass covered dials. Can be used inany location where conditions ofvibration or rough service exist.

GA-77 gauge is very accurate in lowpressure range and ideal for criticalpressure adjustments. Calibrated inounces from 0 to 10 lbs.; in poundsfrom 10 to 30 lbs.

GA Pressure GaugesMODEL SCALE (TYPE) THREAD DIAMETER INLET

GA-73 0 - 30 psi (A, F) 1/4" NPT (M) 2" BottomGA-77 0 - 30 psi (A, F) 1/4" NPT (M) 3-1/2" BottomGA-92 0 - 60 psi (A, F) 1/8" NPT (M) 1-1/2" BottomGA-288 0 - 160 psi (A, F) 1/4" NPT (M) 2" BottomGA-313 0 - 15 psi (A) 1/8" NPT (M) 1-1/2" BottomGA-316 0 - 160 psi (A) 1/4" NPT (M) 2" BackGA-333 0 - 100 psi (A, F) 1/4" NPT (M) 2" BottomGA-338 0 - 160 psi (A) 1/8" NPT (M) 1-1/2" Back

• HARG-510 is a precise, lightweightair regulator and gauge combination.Fits any professional spray gun;comfortable for left and right-handedpainters. Swivel adaptor allows fastinstallation, and a lockring securespressure settings to avoid interruptionsfor readjustments. Max. Air InletPressure: 400 psiOutlet Pressure Adjust. Range:5-100 psiGauge Port Size in Regulator:1/8" NPT (F)

• HAV-500 and HAV-501 are preciseair adjustment valves that controlpressure at the spray gun. Fits allprofessional spray guns. A swivel topallows for easy and fast installation.

• P-H-5516 air adjustment accessoryattaches directly to the spray gunair inlet. The large knurled knobadjusts air flow. Commonly used withspray guns, pressure tanks and pumps.

Air Adjusting ValvesGAUGE

MODEL AIR INLET AIR OUTLET NET WT. RANGE TYPE

HARG-510 1/4" NPS (M) 1/4" NPS (F) 10 oz. 0 - 160 psi Diaphragm(Nipple) (Swivel Adapter) Relieving

HAV-500 1/4" NPS (M) 1/4" NPS (F) (Swivel) 3.5 oz. n/a StraightHAV-501 1/4" NPS (M) 1/4" NPS (F) (Swivel) 5 oz. 0 - 160 psi w/ GaugeP-H-5516 1/4" NPS (M) 1/4" NPS (F) (Swivel) 3 oz. n/a Straight

Air ValvesMAX. OPERATING

MODEL DESCRIPTION PRESSURE MATERIAL

VA-527 3/8" NPS (M) x 3/8" NPT (M) 500 Stainless SteelVA-540 3/8" NPS (M) x 3/8" NPT (M) 500 BrassVA-541 1/4" NPS (M) x 3/8" NPT (M) 500 BrassVA-542 1/4" NPS (M) x 1/4" NPT (M) 500 Brass

HARG-510 HAV-501 HAV-500 P-H-5516



Air VizorTM

Breathable Air Systems

The World’s Most Technologically AdvancedAir Supplied Respirator.

• Protects against isocyanate exposure.• Part of a complete breathable air system.*• NIOSH approved (TC 19C-0365) - meets OSHA

requirements.• Cool and comfortable.• Full lightweight face mask with excellent visibility.

- Ratchet adjustable headgear.- Detachable fabric face shield for excellent durability.- Peel-away face shield protectors improved to

reduce glare.- Detachable hair and neck cover.- Rigid face piece for better visibility over time.- Replaceable visor window for economical servicing.

• Easily accommodates prescription eyewear and beardedemployees.

• Disposable carbon filter and pre-set tamper proofregulator.- 1,000 hour carbon cartridge life- Filter change indicator

• Adjustable belt with quick fit buckle.• Quick connect between visor and waistbelt permits easy

removal of visor.• Air Vizor (MPV-625) includes:

- Full face mask- Belt-mounted filter and regulator- Breathing air tube

* Air VizorTM requires proper air line filtration and carbonmonoxide (CO) monitoring to complete an approvedsupplied air respirator. See next page for proper air linefiltration. A carbon monoxide (CO) monitor may bepurchased locally.

Breathable Air Systems

Belt # ofRegulator Breathable Visor Filtration

Order No. and Hood Air Covers Unit FiltrationModel No. Assembly Hose (30’) Included Included Description

165013 Yes No 2 None --------MPV-625

160019 Yes Yes 12 DAD-503 3-StageMPV-651 Filtration with

Desiccant AirDryer System

160020 Yes Yes 12 HAF-601 3-StageMPV-652 Filtration

System

160018 Yes Yes 12 DAD-502 DesiccantMPV-650 Retrofit

System

41



Air VizorTM

Breathable Air Filtration Units

DAD-503

• Converts shop air into clean, dry,

contaminant-free air for breathingsystems and spray operations.

• 5 micron particulate filter (Stage 1)

• .01 micron coalescing filter (Stage 2)• Charcoal filter for hydrocarbon and odor removal

(Stage 3)

• 28 CFM breathing air regulator• Desiccant system removes water vapor for spray

gun

• 60 CFM spray gun regulator• Automatic drains (Stages 1 and 2)

• Can be used with up to four Air Visors

• 1/2” NPT inlet

HAF-601

• Converts shop air into clean, contaminant-free air

for breathing systems and spray operations

• 5 micron particulate filter (Stage 1)• .01 micron coalescing filter (Stage 2)

• Charcoal filter for hydrocarbon and odor removal

(Stage 3)• 28 CFM breathing air regulator

• 60 CFM spray gun regulator

• Automatic drains (Stages 1 and 2)• Wall-mount bracket

• Can be used with up to four Air Vizors

• 1/2” NPT inlet

DAD-502

• Converts a DAD-500 into a breathing air source

• 5 minute installation. Mounts to top of desiccant

tank• Charcoal filter for hydrocarbon and odor removal

• 13 CFM breathing air regulator. Includes all

necessary fittings• Can be used with one Air Vizor