ITW DeVilbiss Table of Contents - Fluid Air Section.pdf · Order Toll-Free 800-365-7565 2 Govt....
Transcript of ITW DeVilbiss Table of Contents - Fluid Air Section.pdf · Order Toll-Free 800-365-7565 2 Govt....
Spray Guns-Packages-AccessoriesMaximum Performer Features and Benefits .................................................................. 2JGHV Standard Size .................................................................................................... 3JGA-HVLP Suction Feed.............................................................................................. 4MSV Mid-Size .............................................................................................................. 5TGHV Detail/Touch-Up ................................................................................................. 6GFG-HVLP Gravity Feed .............................................................................................. 7GTiTMMillennium/Suction Feed ..................................................................................... 8EXL HVLP Pressure Feed Spray Gun........................................................................... 9EXL HVLP Suction Feed Spray Gun ............................................................................. 9EXL HVLP Gravity Feed Gun ...................................................................................... 10EXL SRi HVLP Spray Gun .......................................................................................... 10FinishLine Gravity and Suction Feed .......................................................................... 11MaxTM Ergonomic Max Performer ............................................................................... 12OMXgt Compliant Gravity Feed .................................................................................. 13EGHV Touch-Up ......................................................................................................... 14Air Cap & Tip Selection Chart ................................................................................ 15-16Air Cap Test Kits ........................................................................................................ 17MBC-510 Manual Spray Gun ...................................................................................... 18JGA-Plus Standard Size Manual Spray Gun ............................................................... 19MSA Mid-Size Manual Spray Gun .............................................................................. 20GFG Gravity Feed Manual Spray Gun ........................................................................ 21EGA Touch-Up Manual Spray Gun .............................................................................. 22Other Equipment and Accessories ............................................................................. 23Spray Equipment Packages .................................................................................. 24-25Solvent SaversTM Hose/Gun Cleaners ......................................................................... 26Fluid Strainers and Equipment ................................................................................... 26
Tanks and CupsQMG Galvanized and QMS Stainless Steel Tanks ................................................. 27-29Tank Accessories .................................................................................................. 30-31Pressure and Suction Feed Cups ............................................................................... 32KB Series Pressure Feed Cups ................................................................................. 33
Clean Air Filtration-AccessoriesCentrifugal Filter-Regulator Units ........................................................................... 34-35Coalescer Filter-Regulator Units ................................................................................. 36Three-Stage Desiccant Unit ........................................................................................ 38Whirl-Wind In-Line Filter ............................................................................................. 39Air Regulators ............................................................................................................ 39Air Control Accessories .............................................................................................. 40Air VizorTM ......................................................................................................... 41-42
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
ITW DeVilbiss Table of Contents
1
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Maximum Performer Features and BenefitsDurability
300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harsh,self-etching primers.
• Dual-seal fluid inlet assures apositive seal.
Drop forged aluminum gun bodiesare strong, durable and lightweight.
Lightweight and precision-balanced for operator comfort.
• Maximum Performer sprayguns are sized to fit both theoperator and the application,with standard-size, mid-sizeand detail/ touch-up models.
2
8
7
9
10
Maintenance• Simple, straightforward design for
easy care and maintenance.
• Economical replacement parts areavailable and easy to install.
64
10
8
13
9
72
5
3
5
6
41Replaceable anodized aluminumbaffle with air cap retaining ringthreads eliminates the need toreplace the gun body shouldthreads become damaged.
Redesigned trigger strike padmakes trigger action smootherand extends air valve life.
• Cartridge-type air valve isdesigned for positive sealingand quick triggering action.
• All gun components have beenlife cycle tested to ensurereliability in productionenvironments.
PerformanceGoldMax™ air caps and specialfluid tip, needle and bafflecombinations provideunparalleled atomization.
• Collectively, MaximumPerformer spray guns canhandle more than 90% of thematerials and coatings beingapplied today, including highersolids materials and higher fluidflows.
Long-life needle packings requirefewer adjustments.
Easy to UseLight trigger action for easyoperation and comfort.
Knurled knobs for easy adjustment of pattern and fluidflow.
1/4" air inlet connects to anystandard compressor system.
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted2
Spray Guns-Packages-Accessories
Our JGHV Standard-Size MaximumPerformer manual spray gun gives youthe best of everything -- the comfortablefit and feel of DeVilbiss’ classic JGAspray gun combined with the hightransfer efficiency and superioratomization of HVLP.
• 300-grade stainless steel fluidpassages for waterbornecompatibility.
Productivity and FinishQuality
The productivity and finish qualityof any Maximum Performer spray gun isdetermined by the air cap and fluid tipcombination.
Technical SpecificationsBody: Drop forged aluminumWeight: 20.8 oz (599 gr)Air Inlet: 1/4” NPS (M)Fluid Inlet: 3/8” NPS (M)Fluid Passages: Stainless steelFeed Type: Pressure feedService Bulletin: SB-2-246Gun Repair Kit: KK-4987-2
Accessories• Remote Cups
Two-quart remote cups are availablein aluminum (KB-555) or stainlesssteel (KB-545-SS).
• Attached CupsOne-quart attached cups are avail-able in aluminum with Teflon®lining (TLC-576) or stainless steel(TSC-591).Note: KK-4980 regulator controlkit is required for use with thesecups and must be ordered separately.
• Additional AccessoriesHose assemblies, air controlregulators, air cap test kits, gun andhose cleaning equipment and otheraccessories also are available.
JGHV Standard-Size Maximum Performer
The versatile JGHV gun delivers a highquality finish with less overspray thanconventional guns.
Ordering Information
The JGHV Standard-Size MaximumPerformer manual spray gun is availablewith the following air cap and fluid tipset-ups, factory assembled for immediatedelivery.
Part No.JGHV-531-28FF* JGHV-531-46FXJGHV-531-28FX* JGHV-531-3-46FF**JGHV-531-33FF* JGHV-531-3-46FX**JGHV-531-33FX* JGHV-531-83DJGHV-531-46FF* JGHV-531-83E*Standard tips and needles are 400-gradestainless steel**Includes 300-grade stainless steel withU.H.M.W. polyethylene seat in fluid tips.
When ordering DeVilbiss spray guns, the partnumber includes information on the specificgun model, air cap and fluid tip you willreceive.
Example: JGHV-531-
Fluid Tip SizeAir Cap Number
Basic Gun Model
Note: JGHV-531-46FF has been tested and verified in U.S.E.P.A. Environmentalverfication program under contract #DAAE30-98-C-1050 with the U.S. Army(TACOM-ARDEC) via EPA Inter-Agency Agreement #DW97936814.See WWW.EPA.GOV/ETV Note: JGHV-531-46FF
NSN#4940-01-315-8352
3
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Ordering InformationThe Classic Series JGA-HVLP
suction feed spray gun is availablewith the following air cap and fluidtip set-ups, factory-assembled forimmediate delivery. Standard tipand needle are 400-grade stainlesssteel.
Part No.JGA-510-57D*
JGA-510-57DE*
* Cup not included. Order separately.
When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you will receive.
The JGA-HVLP suction feed spraygun offers easy-to-use suction feedoperation with the high transferefficiency of HVLP. That means youget the flow rates and uniform spraypatterns you want using conventionalsuction feed fluid delivery.
• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
Technical SpecificationsBody: Drop forged aluminumWeight (Less Cup): 21.4 oz (608 gr)Air Inlet: 1/4" NPS (M)Fluid Inlet: 3/8" NPS (M)Fluid Passages:300 grade stainless steelFeed Type: Suction feedService Bulletin: SB-2-248Gun Repair Kit: KK-4987-2
JGA-HVLP suction feed provides highquality atomization with the hightransfer efficiency of HVLP.
Accessories• One-quart paint cups available in
Teflon®-lined aluminum (TLC-555),aluminum (TGC-545) and stainlesssteel (TSC-595).
• One-pint aluminum cup (TGC-536)is also available.
• Hose assemblies, air controlregulators, gun and hose cleaningequipment and other accessoriesalso are available.
Productivity and FinishQuality
The productivity and finish qualityof any Classic Series spray gun isdetermined by the air cap and fluid tipcombination.
Basic GunModel
Air Cap Number
Fluid Tip Size
Example: JGA-510-
JGA-HVLP Suction FeedClassic Series Spray Gun
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 Gravois Rd.St. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted4
Spray Guns-Packages-Accessories
MSV Mid-Size Maximum PerformerManual HVLP Spray Gun
Our MSV Mid-Size MaximumPerformer spray gun delivers the samehigh transfer efficiency and superiorperformance as the standard-sizedmodel, only in a smaller package.Weighing only 17 ounces, theMid-Size Maximum Performer spraygun is lighter, and it helps reduceoperator fatigue while providingexcellent comfort and control.
• 300-grade stainless steel fluidpassages for waterbornecompatibility.
Ordering Information
TM
Technical SpecificationsBody: Drop forged aluminumWeight: 17 oz (476 gr)Air Inlet: 1/4" NPS (M)Fluid Inlet: 3/8" NPS (M)Fluid Passages: Stainless steelFeed Type: Pressure feedService Bulletin: SB-2-243Gun Repair Kit: KK-4987-2
Accessories• Remote Cups
Two-quart remote cups areavailable in aluminum (KB-555)or stainless steel (KB-545-SS).
• Attached CupsOne-quart attached cups areavailable in aluminum withTeflon® lining (TLC-576) orstainless steel (TSC-591).Note: KK-4980 regulator controlkit is required for use with thesecups and must be orderedseparately.
• Additional AccessoriesHose assemblies, air controlregulators, air cap test kits, gun andhose cleaning equipment and otheraccessories also are available.
* Standard tips and needles are 400-gradestainless steel. 300-grade tips and needles(MSV-531-3) should be used for materialswith pH less than 7.** Includes 300-grade stainless steel withU.H.M.W. polyethylene seat in fluid tip.
When ordering DeVilbiss spray guns,the part number includes informationon the specific gun model, air cap andfluid tip you will receive.
Example: MSV-531-
Air Cap NumberFluid Tip Size
Basic Gun Modelw/400 gr. stainless fluid tip, needle
Productivity and FinishQuality
The productivity and finish quality ofany Maximum Performer spray gun isdetermined by the air cap and fluid tipcombination.
The lightweight MSV spray gun isdesigned for maximum operatorcomfort.
The MSV Mid-Size Maximum Performermanual spray gun is available with thefollowing air cap and fluid tip set-ups,factory assembled for immediate delivery.
Part No.MSV-531-28FF* MSV-531-83DMSV-531-28FX* MSV-531-83EMSV-531-33FF* MSV-531-3-28FF**MSV-531-33FX* MSV-531-3-28FX**MSV-531-46FF* MSV-531-3-46FF**MSV-531-46FX* MSV-531-3-46FX**
5
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Technical SpecificationsBody: Drop forged aluminumWeight: 19 oz. (530g) TGHV-530
24.5 oz. (690g) TGHV-635 with 8 oz. cup 22.4 (635g)
with 2.5 oz. cupAir Inlet: 1/4" NPS(M)Fluid Inlet: 3/8" NPS(M) - TGHV-530
1/4" NPS(M) - TGHV-635Fluid Passages: 300-grade stainless steelAir Consumption: 6.7 SCFM @ 10 psi air
capAir Requirements: 35 psi inlet=10 psi
cap pressureService Bulletin: SB-2-192Gun Repair Kit: KK-5048
TGHV Detail/Touch-Up Maximum PerformerManual HVLP Spray Gun
TM
Part No.TGHV-530-Pressure/Suction Feed*TGHV-635-Gravity Feed*
Our versatile, new TGHV Detail/Touch-Up Maximum Performer spraygun offers superior atomization at thetip, combined with the comfort benefitsof a lightweight, pistol-grip design, sideport fluid inlet for gravity, and standardbottom inlet for pressure/suction feed.
Requiring low air cap pressure, ourTGHV spray gun provides the controlneeded for detail, repair, shading andhighlighting operations. Depending onthe type of feed used, an adjustablespray pattern from 5" to less than 1/4"round makes the TGHV ideal forapplications requiring focused spraypatterns, such as automotive OEM spotrepair, final repair, as well as maskspraying in furniture manufacturing,plastic decorating, and otherapplications requiring small definedpatterns or mask spraying.
• Side port gravity feed with smallerfront end for better operatorvisibility to the spray target.
• 300-grade stainless steel fluidpassages for waterbornecompatibility.
• All TGHV series guns utilizemany of the same high qualitycomponents as DeVilbiss JGA,JGV, MSA, and MSV spray guns.
Productivity and FinishQuality
The productivity and finish qualityof any Maximum Performer spray gunis determined by the air cap and fluidtip combination.
The TGHV Spray Gun is availablein both gravity feed and pressure/suction feed models.
•Model TGHV-530 Pressure/Suction Feed Spray Gun.
•Model TGHV-635 Gravity FeedSpray Gun with Cups (2 1/2 oz.and 8 oz. cups included.)
TGHV Accessories• RemoteCups
Two-quart remote cup is available inaluminum (KB-555) or stainlesssteel (KB-545-SS).
• Gravity Cups2 1/2 oz. (TGHV-407-K10) pkg. of10, 8 oz. (KGP-509-1).
• Additional AccessoriesHose assemblies, air cap test kit, gunand hose cleaning equipment and
other accessories are also available.
Ordering InformationThe TGHV Detail/Touch-Up Maximum
Performer manual spray gun is available inthe following models, factory assembled forimmediate delivery.
TGHV-635 Gravity FeedSupplied with 8 oz.TGHV-415 SS cup
* Standard tips and needles are 300-gradestainless steel (F) .041".
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted6
Spray Guns-Packages-Accessories
GFG-HVLP Gravity FeedClassic Series Spray Gun
When your application calls forhigher transfer efficiency, but you needmore control of the fluid output than youwould get with a suction feed gun,choose the GFG-HVLP gravity feedspray gun. Combining the quality andperformance of HLVP technology withthe advantages of gravity feed fluidflow, the GFG-HVLP spray gun assuresvirtually every drop in the cup is used,so there’s no waste. Clean-up is quickand simple, too.
With gravity feed, atmosphericpressure and gravity itself force thenewer, higher solids materials into thefluid passage, making the gun moreefficient than suction feed. Less air cappressure is required, too.
• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
• Standard equipment includes 20 oz.nylon cup and booth-mount gunhook.
• Drip check in the cup lid preventsleaks and spills from vent hole.
Productivity and Finish QualityThe productivity and finish quality
of any Classic Series spray gun isdetermined by the air cap and fluid tipcombination.
Ordering InformationClassic Series GFG-HVLP gravity
feed spray guns are available with thefollowing air cap and fluid tip set-ups,factory-assembled for immediatedelivery. A new 20 oz. acetal gravity cupis included. Standard tip and needle are400-grade stainless steel.
Part No.GFG-618-57DFFGFG-618-57DFW
When ordering Devilbiss spray guns, thepart number includes information on thespecific gun mode, air cap and fluid tipyou will receive.
Example: GFG-618
Fluid Tip SizeAir Cap Number
Basic Gun Model(including cup)
Technical SpecificationsBody: Drop forged aluminum
Weight (Gun & Cup): 27 oz (768gr)
Air Inlet: 1/4” NPS (M)
Fluid Inlet: 3/8” BSP (F)
Fluid Passages: 300 grade stainless steel
Feed Type: Gravity feed
Service Bulletin: SB-2-169
Gun Repair Kit: KK-5025
Accessories• 8 oz. nylon cup (KGP-510-1).• 32 oz. aluminum cup (GFC-502).• Workbench gun holder (GH-505)
holds the gun upright to facilitatefilling.
• Hose assemblies, air controlregulators, gun and hose cleaningequipment and other accessoriesalso are available.
For smaller production jobs, GFG-HVLPprovides the quality and performance of HLVPtechnology with the advantages of gravity fluidflow.
7
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
GTiTM
MillenniumGTiTM
Compliant HVLPSuction Feed
� Precision engineered #2000 gold air cap - meetsexacting performance demands, producing an extremelyfine finish with all materials. Developed in conjunctionwith top American and European automotive paintcompanies to spray the latest materials.
� Optimum atomization for clearcoats and single stagesProduces high gloss finish and minimizes orange peel.Excellent fluid control for applying more film build withfewer passes.
� Lightweight and comfortable. Classic JGA fit and feel,yet lighter weight. Gun body styling changes forimproved comfort
� Easy to clean - Plated gun body is gun washer safe andmaintains its “like new” appearance.
� Quick cleanup and upside-down spraying (with nocup lid leaks) - with E-Z LinerTM disposable cup liners.
� GTi Millennium HVLP Spray Gun includes: 1.3mm,1.4 mm, and 1.5 mm fluid tips; 32 oz. aluminum cup(120175/GFC-502) with push on lid; air adjusting valvewith gauge (180006/HAV-01); air cap cleaning kit, spraylube, fluid filter, gun hook; (9) E-Z Liner disposableliners (190966/OMX-70-K48)
� Waterborne compatible - stainless steel fluid tip andneedle, electroless nickel-plated gun body inside andout.
� Lightweight and comfortable - familiar JGA fit andfeel, yet 24% lighter.
� Accurate, repeatable settings - pointers on fluidand fan controls.
� Virtually maintenance-free! - No gaskets,self-sealing.
� Simple, easy-to-use suction feed operation allowspainters to spray with the method they’re used to.
� GTi suction feed gun includes:TGC one quart-cupAir adjusting valve with gauge.
GTi Compliant Suction FeedOrder No. Fluid Inlet AirModel No. Tip (mm) Pressure Applications
170146 2.0 20-25 psi Base coatsGTI-600S 25-30 psi Low and high solids,
clear coats, singlestages
Test
ed/V
erifie
d ETV
/EPA
See W
WW
.EPA
.GO
V.ETV
GTi Millennium Gravity FeedOrder No. Fluid Inlet AirModel No. Tip (mm) Pressure Applications
170156 1.3 & 1.4 20-25 psi Base coatsGTI-620G 25-30 psi High solids clear coats(includes 1.3 & 1.4 mm and single stagesand 1.5 mm fluid tips)
1.5 20-25 psi Base coats25-30 psi Low solids, clear
coats, single stagesand waterbornes
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted8
Spray Guns-Packages-Accessories
EXLHVLP Pressure FeedSpray Gun� Precisionengineered patented#2000 air cap - Meetsexacting performancedemands, producing anextremely fine finish withall materials. Developed inconjunction with topAmerican and Europeanpaint companies tospray the latest materials.
� Large Spray Pattern forfast coverage.
� Even distribution ofmaterials for no mottling or striping - Excellent colormatching capabilities
� Lightweight and comfortable - Classic DeVilbiss fit andfeel
� Economical servicing - Air cap, fluid tips and needlesare fully interchangeable and available separately.
� Highly efficient HVLP design - Complies withenvironmental regulation requiring high volume,low pressure. Saves material. Very little overspray.
� Stainless steel fluid tip, needle and fluid inlet adapter.
Technical Specifications
Inlet Air AirModel No. Tip (mm) Cap Applications
EXL-520P-11 1.1 2000 Low to medium solidsUp to 12 oz./min.
EXL-520P-14 1.4 2000 High solidsUp to 12 oz./min.
EXL-520P-18 1.8 2000 High solidsUp to 16 oz./min.
EXL-520P-22 2.2 2000 High solidsUp to 18 oz./min.
Specifications30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm airvolume
Anodized fluid passages
EXLHVLP Suction Feed
Spray Gun
� Precision engineered patented#2000 air cap - Meets exactingperformance demands, producing anextremely fine finish with all materi-als. Developed in conjunction withtop American and European paintcompanies to spray the latestmaterials.
� Large Spray Pattern for fastcoverage.
� Even distribution of materials forno mottling or striping - Excellentcolor matching capabilities
� Lightweight and comfortable - Classic DeVilbiss fit andfeel
� Economical servicing - Air cap, fluid tips and needlesare fully interchangeable and available separately.
� Highly efficient HVLP design - Complies withenvironmental regulation requiring high volume,low pressure. Saves material. Very little overspray.
� Stainless steel fluid tip, needle and fluid inlet adapter.
Includes: Air Cap Cleaning Kit, Spray Gun Lube
Technical Specifications
Inlet Air AirModel No. Tip (mm) Cap Applications
EXL-520S-18 1.8 2000 Base coat 20-25 psiinlet pressure
EXL-520S-22 2.2 2000 Low and high solidsclear coats and singlestages 25-30 psiinlet pressure
Specifications30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm airvolume
Anodized fluid passages
9
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
EXLHVLP Gravity Feed
Spray Gun� Precision engineeredpatented #2000 air cap - Meetsexacting performance demands,producing an extremely fine finishwith all materials. Developed inconjunction with top Americanand European paint companies tospray the latest materials.
� Large Spray Pattern for fastcoverage.
� Even distribution of materi-als for no mottling or striping -
Excellent color matching capabilities
� Lightweight and comfortable - Classic DeVilbiss fit andfeel
� Economical servicing - Air cap, fluid tips and needlesare fully interchangeable and available separately.
� Highly efficient HVLP design - Complies withenvironmental regulation requiring high volume,low pressure. Saves material. Very little overspray.
� Stainless steel fluid tip, needle and fluid inlet adapter.
� Less time spent on refills - True 1-Liter aluminum cupwith disposable push-on lid
� Quick clean up and upside down spraying (no cupleaks) - with E-Z LinerTM disposable cup liners
Includes: Air Cap Cleaning Kit, Spray Gun Lube
Technical Specifications
Specifications30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm airvolume
Anodized fluid passages
Inlet Air Inlet AirModel No. Tip (mm) Pressure Applications
EXL-620G-15 1.5 20-25 psi Base coat25-30 psi Low solids clear coats
single stagesEXL-620G-18 1.8 20-25 psi High solids and
25-30 psi single stages
EXL-620G-22 2.2 20-25 psi High solids and25-30 psi single stages
DeVilbiss SRiTM
HVLP Spray Gun
Fine Atomization and Spot Repair Versatility
Finally - a spot repair spray gun with the control needed forspot repairs plus the comfort of a full-size spray gun. TheDeVilbiss SRITM is the ultimate spot repair spraygun with the fit and feel of a full size spraygun combined with the pattern range andversatility needed for invisible, top qualityspot repairs.
Maximum Control Means MaximumPerformance� Small gun proportions� Ergonomically styled for operatorcomfort� Full fan and spot patterns for spray
versatility� Full size air and fluid controls� Cheater value for precision air adjustments at
the spray gun.� Single finger trigger adjusts from fine feathering to
fadeouts� Uniform material distribution
Includes:1.0 mm fluid tip or 1.2 mm tip, 4 oz. disposable cup and lid. Wrench(SRi-50), Spray lube (SSL-10)
Specifications:29 psi air inlet pressure delivers 10 psi air cap pressure at 4.5 cfmair volume required. (SRi-5033-205) Air Cap test Kit (orderseparately) Provides consistent setup and regulatory proof of aircap pressure.
*Note: For finer control at lower fluid flows, order the optional .8mm tip and needle separately.
Technical Specifications
Maximum Air Pressure: 100 psi (7 bar)Gun Body: Anodized AluminumNozzle and Needle: Stainless SteelCup: NylonCup Lid: PolypropyleneAir Inlet Size: Universal 1/4” BSP & NPS (M)Gun Weight: 13.7 oz.Gun Repair Kit: SRi-426
Inlet Air Inlet AirModel No. Tip (mm) Pressure Applications
SRi-628-10 1.0 20-29 psi Spot repairs
SRi-628-1.2 1.2 20-29 psi Panel repairs,Door jambs
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted10
Spray Guns-Packages-Accessories
FinishLineGravity Feed
FinishLineSuction Feed
� Economically-priced
� Available in conventional or compliant HVLP models
� Durable, high quality construction: High gradedie-case alloy gun body. Stainless steel fluid inlet.Alloyed resins for other components to keep gunweight to a minimum. All materials resistant to solventsand gun-washing fluids.
� Precision engineered to produce well atomized,uniform spray patterns
� Easy-to-use controls: Precise spray pattern and fluidflow adjustment. Patented spray pattern knob hasmarker for repeatable settings from full fan to roundspray.
� Waterborne compatible: Stainless steel fluid inlet andfluid needle, plus alloy resin fluid tip.
� 20-oz. lightweight acetal cup with screw-on lid:Built-in “drip check” helps prevent leaks through lidvent hole.
� Quick clean-up and upside-down spraying with no cupleaks with E-Z linerTM disposable cup liners.
� Includes: 20 oz. acetal cup (514302/FLG-502); 4 E-ZLinerTM disposable cup liners (190966/OMX-70-K48);1.4 mm fluid tip (conventional gun); 1.8 mm and 1.6 mmfluid tips (compliant HVLP gun); air adjusting valvewith gauge (180006/HAV-501)(compliant HVLP gun)
Order No. Type Fluid AirModel No. Tip (mm) Cap Applications
512114 Conventional 1.4 #1 General purpose,FLG-611-114 light to heavy
viscosity materials
512318 Compliant 1.8/1.6* #3 General purpose,FLG-631-318 HVLP light to heavy
viscosity materials
* Compliant HVLP models come standard with two sizes of fluid tips
Order No. Type Fluid AirModel No. Tip (mm) Cap Applications
510116 Conventional 1.6 #1 General purpose,FLG-611-114 light to medium
viscosity materials
510-322 Compliant 2.2/1.8* #3 General purpose,FLG-622-322 HVLP light to medium
viscosity materials
* Compliant HVLP models come standard with two sizes of fluid tips
� Economically-priced
� Available in conventional or compliant HVLP models
� Durable, high quality construction: High gradedie-case alloy gun body. Stainless steel fluid inlet.Alloyed resins for other components to keep gunweight to a minimum. All materials resistant to solventsand gun-washing fluids.
� Precision engineered to produce well atomized,uniform spray patterns
� Easy-to-use controls: Precise spray pattern and fluidflow adjustment. Patented spray pattern knob hasmarker for repeatable settings from full fan to roundspray.
� Waterborne compatible: Stainless steel fluid inlet andfluid needle, plus alloy resin fluid tip.
� TGC one-quart aluminum “drip-free” suction cup:Two position valve allows operation as a “drip-free”cup or as a conventional suction cup. “Drip-freediaphragm” helps prevent leaks through lid vent hole.
� Includes: TGC one-quart suction feed cup (12001/TGC-545); 1.6 mm fluid tip (conventional gun); 2.2 mmand 1.8 mm fluid tips (compliant HVLP gun); Airadjusting valve with gauge (18006/HAV-501)(compliant HVLP gun.
11
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Max™ Ergonomic Maximum PerformerManual HVLP Spray Gun
Our MAX HVLP spray gun combines ergonomic design with DeVilbiss’ exclusive Maximum PerformerTM
atomization technology to help finishing operations achieve a Class A finish using less air. Value priced fortoday’s high production finishing applications, and weighing just 12 oz., the MAX features solvent resistant,engineered resin materials. Designed with the operator in mind, the small grip size and short grip span, atwo-pound trigger pull force and a pneumatic trigger pull of one-pound, are ideal for smaller hands. The MAXfeatures a nylon-lined, flexible fluid hose with swivel air hose connection so finishers can maneuver easily.
Production and Finish QualityThe productivity and finish quality ofany Maximum Performer spray gun isdetermined by the air cap and fluidcombination. Depending on thecombination, the MAX can handleup to 72% solids by volume.
Ordering InformationThe MAX ergonomic spray gun isavailable with the following air cap andfluid tip set-ups, factory assembled forimmediate delivery.MAX-504-46FFP (.055” fluid tip)MAX-504-83EP (.070” fluid tip)MAX-504-46FXP (.042” fluid tip)
Technical SpecificationsBody: Engineered Resins
Weight (Gun & Cup): 12 oz (454gr)
Air Inlet: 1/4” NPS (M)
Fluid Inlet: 3/8” NPS (male)
Fluid Passages: Engineered Resin,
Teflon, Stainless Steel
Air Consumption: 23 SCFM @ 65 psi
inlet (46MP); 23 SCFM @ 65 psi inlet
(83MP)
Air Requirements: 65 psi inlet =
10 psi at air cap
Service Bulletin: SB-2-226
Gun Repair Kit: KK-5054
Accessories• Air Cap Test Kit: Includes air cap
and gauge to demonstrate actualpressure being used at the cap
• KK-5033-46MP: For use with 46 MPair cap only
• KK-5033-83MP: For use with 83 MPair cap only
Hose assemblies, air controls, pressuretanks, cups, gun and hose cleaningequipment and other accessories arealso available
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted12
Spray Guns-Packages-Accessories
OMXgt Compliant Gravity Feed
• Super performance - 100% gold air cap providesexcellent atomization of low V.O.C. compliantmaterials with less overspray and lessorange peel. Excellent with high solids.
• Complies with environmental regulationsrequiring HVLP.
• Eliminates need for multiple tips and needles -Fluid control valve adjusts from .8mm to 1.8mm
• The ultimate in painter comfort - Lightweight(only 19 oz.) and well-balanced. Top trigger foreasy spraying of horizontal surfaces withoutbending wrist. Light trigger pull -- 2 lbs. vs.competitors’ 5-6 lbs.
• Waterborne-compatible.
• Easy cleanup and identification of spray gun -Disposable black grips on gun; also available inred. Conveniently identifies basecoat orclearcoat gun.
• Quick cleanup and upside-down spraying -(with no cup lid leaks) with E-Z linerTM
disposable cup liners.
• Includes:Air inlet mini-gauge (192012/OMX-148)Air adjusting valve (HAV-500)28-oz Delrin cup (190977/OMX-467)Red grips (192056/OMX-490)Gun holder (190967/OMX-114)(9) E-Z LinerTM disposable cup liners(190966/OMX-70-K48)Fluid tube cleaning brush (190976/OMX-465)Free instructional video with warranty cardreturn
• Specifications:30 psi air inlet pressure delivers10 psi air cap pressure at 16 cfm air volumerequired.192059 (OMX-5033-100) Air Cap Test Kit
OMXgt Compliant Gravity Feed
*Fluid TipOrder No. Setting Inlet Air
(mm) Pressure Applications
570008 1.4 20-25 psi Base coatsOMX-610 25-30 psi High solids, clear coats
and single stages25-30 psi Waterbornes
1.6 20-25 psi Base coats25-30 Low solids clear coats
and single stages*Adjustable fluid control valve
13
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
EGHV Touch-Up Maximum Performer
Comfortable and easy-to-use, the EGHV Touch-UpMaximum Performer spray gun provides precise control forthe most exacting detail and touch-up work. The gun featuresa long tapered fluid needle and a top-mounted trigger, andweighs only 7.5 ounces, making it ideal for hours offatigue-free precision painting.• Fluid delivery by attached suction feed or remote
pressure feed cup.• Knurled knobs for fine adjustment of fluid flow and
spray pattern.
Productivity and Finish QualityThe productivity and finish quality of any Maximum
Performer spray gun is determined by the air cap and fluid tipcombination.
Ordering InformationThe EGHV Touch-UP Maximum Performer manual spray
gun is available with the following air cap and fluid tip setup,factory assembled for immediate delivery.
Part No:EGHV-531-397E*
*All wetted surfaces of EGHV are stainless steel
Technical Specifications
Body: Drop forged aluminumWeight: 7.5 oz. (210 gr)Air Inlet: 1/4” NPS (M)Fluid Inlet: 1/4” NPS (M)Fluid Passages: Stainless SteelFeed Type: Suction feed
Pressure feedAir Consumption: 4.3 CFM max. @
10 psi cap pressureAir Cap Pressure: 10 psi @ 80 psi inletService Bulletin: SB-2-166Gun Repair Kit: KK-5044
EGHV Accessories• 8 Oz Cup (TGS-503) Solvent-resistant
polyethylene cup is available.• Remote Cups
Two-quart remote cups are available inaluminum (KB-555) or stainless steel(KB-545-SS)
• Additional AccessoriesHose assemblies, air cap test kit, gunand hose cleaning equipment and otheraccessories also are available.
EGHV-532 gun and TGS-503 translucent polyethylenecup provide a precision finish with less overspray.
HVLP Spray Gun
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted14
Spray Guns-Packages-Accessories
Air Cap & Tip Selection ChartJGHV, MSV and AGXV
Medium solidsenamels, urethanes,solvent and water-borne furnituretopcoats, waterborneautomotive OEMfinishes, corrosionprotective coatings,leather stains, acrylics,epoxies, etc. 22.5 CFM
** Recommended Fluid Tips Shown. Other Sizes Are Available.* Viscosity Cup Reference18 Seconds #4 Ford = 22 Seconds ZAHN #222 Seconds #4 Ford = 24 Seconds ZAHN #228 Seconds #4 Ford = 30 Seconds ZAHN #2
Up To12 oz./min.
11"
18.0 CFM
FX (.042")
Most common, lowsolids coatings, i.e.enamels, lacquers,stains, sealers, primers,waterborne adhesives,etc.
Low solids automotivefinishes, enamels,lacquers, stains,sealers, etc. 9" FX (.042")
18.75 CFMUp to
12 oz./min.
12-16 oz./min.
11" FF (.055")
Medium-high solidsenamels, urethanes,low VOC waterbornefurniture topcoats,porcelain enamel,corrosion protectivecoatings, acrylics,epoxies, etc.,architectural andindustrial maintenancecoatings.
26.0 CFM
Low solids, up to25% solids byvolume
Up to 24 seconds,#4 Ford cup
Low solids up to25% solids byvolume
Up to 24 seconds,#4 Ford cup
Low-medium solids,up to 50% solids byvolume
Up to 28 seconds,#4 Ford cup
Medium-high solids,up to 72% solids byvolume
Over 28 seconds,#4 Ford cup
#46 MP
JGHV-101-46MP
#83 MP
JGHV-101-83MP
TYPICALCOATINGSUSED WITH
*TYPICALSOLIDS BYVOLUME
VISCOSITIES
AIR CAPMODEL NO.
PART NO.
AIRVOLUME(AT 10 psiAIR CAP
PRESSURE)
TYPICALFLUIDFLOWRATES
#28
JGHV-101-28
#33A
JGHV-101-33A
** RECOM-MENDED
FLUIDTIPS
PATTERNSIZE
Over16 oz./min.
13" E (.070") orD (.086")
15
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Detail, touch-upenamels, lacquers,etc.
TYPICALSOLIDS BYVOLUME
VISCOSITIES
Low solids,up to 25%solids byvolume
Up to 24seconds,#4 Ford cup 4.3 CFM
F (.041")
Air Cap & Tip Selection ChartEGHV and TGHV
TYPICALCOATINGSUSED WITH
AIRVOLUME(AT 10 psiAIR CAP
PRESSURE)
TYPICALFLUIDFLOWRATES
#395HV
EGHV-439397HV
RECOM-MENDED
FLUIDTIP
* PATTERNSIZE
Detail, touch-upenamels, lacquers,etc.
Low solids,up to 25%solids byvolume
Up to 24seconds,#4 Ford cup 6.7 CFM
F (.041")#90HV
CV-39-90HV
* Spray pattern size dependent upon type of feed, material viscosity, and air cap pressure.
AIR CAPMODEL NO.
PART NO.
Up to4"
Up to5"
Up to 1-1/2 oz./min.
Up to 4 oz./min.
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 Gravois Rd.St. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted16
Spray Guns-Packages-Accessories
Air Cap Test Kits*
• KK-5033-83-MP Air Cap Test Kit –Includes air cap and gauge, for usewith #83MP air caps only.
• KK-5033-90-HV Air Cap Test Kit –Includes air cap, gauge and ring, foruse with #90HV air caps only.
*Air cap test kits may be required by some airquality agencies. These kits are supplied with aspecial air cap and test gauge to demonstrateactual pressure being used at the cap since itwill vary depending on hose length between theair regulator and gun. This kit can be used as aquality control device for consistent sprayingeach day. The cap kit should not be used whenfinishes are being applied.
Fluid Tips and Needles
• KK-5034 Air Cap Test Kit –Includesair cap and gauge, for use with#397HV air caps only.
• KK-5033-28 Air Cap Test Kit –Includes air cap and gauge, for usewith #28 air caps only.
• KK-5033-33A Air Cap Test Kit –Includes air cap and gauge, for usewith #33 or #33A air caps only.
• KK-5033-46-MP Air Cap Test Kit –Includes air cap and gauge, for usewith #46MP air caps only.
ORDER TIPNUMBER ON FLUID TIP AND NEEDLE SET
For JGHV and MSVAV-2115-FF, FX JGA-4040-FF, FX*AV-2120-D, E, FF, FX JGA-4045-D, E, FF, FX*AV-4915-FF, FX JGA-4056-FF, FX**AV-4920-FF, FX JGA-4051-FF, FX**
For AGXVAV-2115-FF, FX AGX-4402-FF, FX*AV-2120-D, E AGX-4483-D,E*AV-2120-FF, FX AGX-4600-FF, FX*AV-4915-E, FF, FX AGX-4300-E, FF, FX**AV-4920-FF, FX AGX-4613-FF, FX**
For EGHVEGA-60-F EGA-4000-F*
For TGHVCV-30-F-HV TGHV-4000-F***
* 400-grade stainless steel (lapped).** 300-grade stainless steel with U.H.M.W. polyethylene seat in fluid tip (matched set).*** 300-grade stainless steel (lapped).
17
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Combining a drop forged aluminumbody with a forged removable sprayhead, the MBC-510 spray gun is idealfor applications that require maximumoutput and quick changeovers.
• Removable spray head allows forreduced downtime on nozzlecombination changeovers.
• MBC spray guns have nickel-platedbrass fluid passages and 400-gradestainless steel fluid tip and needle.
Productivity and FinishQuality
The productivity and finish qualityof any DeVilbiss conventional airspray gun is determined by the air capand fluid tip combination.
Ordering InformationThe MBC-510 manual air spray gun
is available with the following air capand fluid tip set-ups, factory-assembledfor immediate delivery. However, theseare only the most popular set-ups – forother air cap and tip combinations thatcan be ordered separately.
Part No.MBC-510-30EXMBC-510-58EXMBC-510-62HDACMBC-510-64HDDMBC-510-69HDDMBC-510-704EMBC-510-704FF
MBC-510-704FXMBC-510-765EMBC-510-765FFMBC-510-765FXMBC-510-78EMBC-510-797EMBC-510-797FF
Basic Gun ModelAir Cap Number
Example: MBC-510-
MBC-510 Manual Spray GunWith Removable-Head
These guns with fluid tip and needlecan be ordered separately without aircap and retaining ring:
Part No.MBC-510-ACMBC-510-DMBC-510-E
The stainless steel fluid tip has aspecially designed composite fluidseat insert to extend service life andprevent leakage. The gun alsofeatures a Delrin® air cap andretaining ring, along with aremovable spray head for easycleaning.
Technical Specifications
Body: Drop forged aluminumWeight: 23.6 oz. (661 gr) withair cap and ringAir Inlet: 100 psi max, 1/4" NPS
(M)Fluid Inlet: 100 psi max, 3/8" NPS
(M)Fluid Passages: Nickel-plated brassWetted Parts: 300 and 400-grade
stainless steelComposite Nickel-plated brass
Feed Type: Pressure feedService Bulletin: SB-2-303Gun Repair Kit: KK-4058-1
MBC-510-EXMBC-510-FFMBC-510-FX
Fluid Tip Size
When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you willreceive.
Technical Specifications
Body: Drop forged aluminumWeight: 27 oz. (756 gr) with air
cap and ringAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 100 psi max, 3/8" NPS(M)Fluid Passages: Nickel-plated brassWetted Parts: Nickel-plated brass
400-grade stainless steelFeed Type: Pressure feed
Suction feedService Bulletin: SB-2-301Gun Repair Kit: KK-4058-1
Accessories• Hose assemblies, air control, pressure
tanks, cups, gun and hose cleaningequipment and other accessories areavailable.
Manual Spray Gun
MBC-Zinc™
Engineered for the trouble-freeapplication of zinc-rich primers, theMBC-Zinc spray gun eliminates leakyfluid tips and zinc-plated air caps.
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted18
Spray Guns-Packages-Accessories
JGA-Plus Standard SizeManual Spray Gun
* Models include 400-grade stainlesssteel tips and needles.** Models include “premium”300-grade stainless steel tip withU.H.M.W. polyethylene insert (needleseat) and 300-grade stainless steelneedle.
When ordering DeVilbiss spray guns,the part number includes informationon the specific gun model, air cap andfluid tip you will receive.
• Maximum 8 oz./min. fluid flow.• Lower solids coatings.• Medium to high V.O.C. coatings
(4.0-5.0 lbs./gal.).• Smaller compressors - 3 h.p. is
usually sufficient.• Limited air supply - requires only
11 CFM at 10 PSI air cappressure.
• Class “B” finish qualityrequirements.
JGA-HVLP and MSA-HVLP Application GuideThe economical way to convert
DeVilbiss conventional air spray gunsto Classic Series HVLP performanceby using a conversion kit. Simple toconvert for on-site retrofit.
JGA/MSA-TEK offers a simpleconversion to HVLP pressure feed by
changing the air cap, baffle and bafflegasket.
Setting industry standards forhigh-production performance, theJGA-Plus standard-size manual spraygun also offers the comfortable fit andfeel operators prefer. An economicaloption for waterborne and solvent-based material applications, theJGA-Plus stainless steel air spray gundelivers the quality results you needfor tough applications.
• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
Productivity and FinishQuality
The productivity and finish quality ofany DeVilbiss conventional air spraygun is determined by the air cap andfluid tip combination.
Ordering InformationThe JGA-Plus standard-size spray gun
is available with the following air capand fluid tip set-ups, factory-assembledfor immediate delivery. However, theseare only the most popular set-ups – forother air cap and tip combinations thatcan be ordered separately.
Part No.JGA-510-30EXJGA-510-90EXJGA-510-704EJGA-510-704FFJGA-510-704FXJGA-510-705FFJGA-510-705FX
These guns with fluid tipand needle can be orderedseparately without air capand retaining ring:
Part No.JGA-510-D* JGA-510-FX*JGA-510-E* JGA-510-3-FF**JGA-510-EX* JGA-510-3-FX**JGA-510-FF*
JGA-510-765EJGA-510-765FFJGA-510-765FXJGA-510-797EJGA-510-797FFJGA-510-80EX
Example: JGA-510-
Basic Gun ModelAir Cap Number
Fluid Tip Size
Technical SpecificationsBody: Drop forged aluminumWeight: 21.6 oz. (613 gr) with air
cap and ringAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 100 psi max, 3/8" NPS (M)Fluid Passages: 300-grade stainless steelFeed Type: Pressure feed,
Suction feed (EX)Service Bulletin: SB-2-252Gun Repair Kit: KK-4987-2
Accessories
• Hose assemblies, air control,pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.
• For optional tip and needle sets.
19
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Technical Specifications
Body: Drop forged aluminum Weight:
18.4 oz. (515 gr)
Air Inlet: 100 psi max, 1/4" NPS (M)
Fluid Inlet: 150 psi max, 3/8" NPS (M)
Fluid Passages: 300-grade stainless steel
Wetted Parts: 300 and 400-grade
stainless steel, hardened alloy
Feed Type: Pressure feed
Service Bulletin: SB-2-319
Gun Repair Kit: KK-4987-2
Designed to help reduce operatorfatigue while offering excellentcomfort and control, the MSA midsizespray gun is lighter and more compactthan our standard-size JGA gun. Thatmeans you get the same quality andhigh-efficiency performance providedby our JGA-Plus spray gun, in asmaller model that weighs only 17ounces.
• 300-grade stainless steel fluidpassages offer waterbornecompatibility, corrosion resistanceand protection from harshself-etching primers.
• Air caps and replacement parts areinterchangeable with JGA sprayguns (the air inlet fitting is the onlyexception).
Productivity and FinishQuality
The productivity and finish qualityof any DeVilbiss conventional airspray gun are determined by the aircap and fluid tip combination.
Ordering InformationThe MSA midsize spray gun is
available with the following air cap andfluid tip set-ups, factory-assembled forimmediate delivery. However, these areonly the most popular set-ups – for otherair cap and tip combinations that can beordered separately.
Part No.MSA-510-35LEMSA-510-35LFFMSA-510-35LFXMSA-510-704LE
Decorator Spray GunMSA-510-DEC
The MSA-510-DEC decorator spraygun features a spatter cap to createdecorative textured finishes.
Can be converted to HVLP.
These guns with fluid tip and needlecan be ordered separately without aircap and retaining ring:
Part No.MSA-510-E*MSA-510-EX*MSA-510-FF*MSA-510-FX*
MSA-510-3-E**MSA-510-3-FF**MSA-510-3-FX**
MSA-510-704LFFMSA-510-704LFXMSA-510-797LEMSA-510-797LFF
* Models include 400-gradestainless steel tips and needles.** Models include “premium”300-grade stainless steel tip withU.H.M.W. polyethylene insert(needle seat) and 300-gradestainless steel needle.
When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gunmodel, air cap and fluid tip youwill receive.
Technical SpecificationsBody: Drop forged aluminum
Weight: 17 oz. (476 gr)
Air Inlet: 100 psi max, 1/4" NPS (M)
Fluid Inlet: 100 psi max, 3/8" NPS (M)
Fluid Passages: 300-grade stainless steel
Feed Type: Pressure feed
Suction feed
Service Bulletin: SB-2-257
Gun Repair Kit: KK-4987-2
Accessories• Hose assemblies, air control,
pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.
• For optional tip and needle sets.
Example: MSA-510-
Basic Gun ModelAir Cap Number
Fluid Tip Size
MSA Mid-Size Manual Spray Gun
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted20
Spray Guns-Packages-Accessories
Combining the advantages ofgravity feed fluid delivery withadvanced quality and performance, theGFG-617 conventional air spray gunoffers high transfer efficiency forsmall applications that require full,uniform coverage. Fitted with atop-mounted gravity feed cup thatmakes filling simple and quick, theGFG-617 spray gun uses virtuallyevery drop of paint in the cup, evenwhen working with very smallamounts of material.
• 300-grade stainless steel fluidpassages offer waterborne.
compatibility, corrosion resistanceand protection from harshself-etching primers.
• Standard equipment includes a20 ounce acetal cup and
booth-mount gun hook.
• Drip check in the cup lid virtuallyeliminates leaks and spills from thevent hole.
Productivity and FinishQuality
The productivity and finish qualityof any DeVilbiss conventional airspray gun is determined by the air capand fluid tip combination.
Ordering InformationThe GFG-617 gravity feed spray
gun is available with the following aircap and fluid tip set-ups,factory-assembled for immediatedelivery.
Part No.GFG-618-80FWGFG-618-90FFGFG-618-90FW
GFG Gravity Feed Manual Spray Gun
When ordering DeVilbiss sprayguns, the part number includesinformation on the specific gun model,air cap and fluid tip you will receive.
Accessories• 8 oz. nylon cup (KGP-509-1).• 32 oz. aluminum cup (GFC-502).• Hose assemblies, air control, gun and
hose cleaning equipment and otheraccessories are also available.
Basic Gun Model(including cup)
Air Cap Number
Fluid Tip Size
Example: GFG-618-
Technical SpecificationsBody: Drop forged aluminumWeight: 27.5 oz. (770 gr) with
paint cupAir Inlet: 100 psi max, 1/4" NPS (M)Fluid Inlet: 3/8" BSP (F)Wetted Parts: 300 and 400-grade
stainless steelFeed Type: Gravity feedService Bulletin: SB-2-179Gun Repair Kit: KK-5025
Supplied with a32 oz. aluminum cup
21
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
EGA Touch-Up Manual Spray Gun
The gun of choice for touch-up,shading, edging and detail decorating,the EGA touch-up gun providesprecise control for any type of delicatespray finishing applications. Designedfor external mixing applications, thegun features a forefinger trigger toenhance operator control, and a longneedle taper to make detail work easy.
• Equipped with stainless steel tipand needle.
• Knurled knobs allow fine sprayadjustments for fluid and patterncontrol.
Productivity and FinishQuality
The productivity and finish qualityof any DeVilbiss conventional airspray gun is determined by the air capand fluid tip combination. Body: Drop forged aluminum
Weight: 7 oz. (196 gr) with air capand ring
Air Inlet: 1/4" NPS (M)Fluid Inlet: 1/4" NPS (M)Wetted Parts: Aluminum 400-grade
stainless steelFeed Type: Pressure feed
Suction feedService Bulletin: SB-2-163Gun Repair Kit: KK-5044
Accessories• Hose assemblies, air control,
pressure tanks, cups, gun and hosecleaning equipment and otheraccessories are also available.
Note: EGA-503 model replacesEGA-502.
Basic Gun ModelAir Cap Number
Fluid Tip Size
Example: EGA-503-
Ordering InformationThe EGA touch-up gun is available with
the following air cap and fluid tip set-ups,factory-assembled for immediate delivery.
Part No.EGA-503-390F
When ordering DeVilbiss spray guns, thepart number includes information on thespecific gun model, air cap and fluid tip youwill receive.
Technical Specifications
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted22
Spray Guns-Packages-Accessories
Other Equipment and Accessories
Spray Gun LubeSSL-10-K12
Specially formulated spray gun lubeimproves performance and extends thelife of spray equipment. Contains nosilicones or petroleum distillates tocontaminate paint and coatings. Caseof 12 (2-oz.) bottles. Not for use withair tools and high RPM equipment.
Spray Gun Wrench
WR-103
Versatile tool fits fluid and air hoseconnections, as well as adapters andpacking nuts.
JGA Gun Fluid TubeJGA-444
Handy tube combines the fluid andair hoses at the gun handle to preventtwisted lines and keep hoses fromdragging over work. 3/8” NPS thread.
Disposable Spray Gun CoversSave money by reducing cleaning
time and maintenance with thesecovers that also limit operatorexposure to overspray.GC-100-K4 (pkg. of 4)GC-100-K48 (pkg. of 48)
PART NO. MALE MALE FEMALE
AD-404 – 1/4" NPS 3/8" NPSP-H-4105 – 3/8" NPS 1/4" NPSH-1766 1/8" NPT 1/4" NPS –H-2008 1/4" NPT 1/4" NPS –AD-31 1/4" NPS 1/4" NPS –AD-26 1/4" NPS 3/8" NPS –H-1580 1/4" NPT 3/8" NPS –H-1446 3/8" NPS 3/8" NPS –AD-11 3/8" NPS 3/8" NPT –
Cleaning BrushesFor cleaning the threads and recesses of
the gun body.3/8" dia. brush: 42884-214-K5 (pkg. of 5)5/8" dia. brush: 42884-215-K10 (pkg. of 10)
Thread AdapterThread adapters provide the correct
hook-up for spray guns, hoses, tanksand other spray equipment. Theywork with most standard threadapplications.
23
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Spray Equipment
JGHV-531-46FF (.055)DeVilbiss MAXIMUM PERFORMER HVLP spray gun, medium solids,enamels, top coats, Aerospace, automotive OEM finishes, corrosionprotective coatings, acrylics, epoxies up to 50% solids (12-16 oz.min./28 seconds #4 Ford). Stainless Steel fluid passages and stainless steeltip and needle with 46MP air cap, maximum 11” pattern.
Maximum Performer HVLP spray guns also meet operationalrequirements of California South Coast Air Quality ManagementDistrict and other air quality authorities. DeVilbiss HVLP spray gunsare protected by Patents 5,344,078, 5,209,405 & 5,090,623.
KK-4987-2 Repair Kit. Used on JGHV, MSV, MSA and JGAspray guns
KB-555 - 2 quart aluminum remote pressure cup
KB-545-SS - 2 quart Stainless Steel remote pressure cup
TLC-576 - 1 quart aluminum pressure cup (for attached use)TSC-591 - 1 quart Stainless Steel cup (for attached use)
(must use KK-4980 regulator, purchase separately)
QMGT-5223 - 2 gallon ASME galvanized pressure tank, doubleregulation, agitator and air motor
QMST-5223 - 2 gallon ASME stainless steel pressure tank, doubleregulation, agitator and air motor
KB-4006 - 6 ft. hose sets (air and fluid) with fittings for use withremote KB cups
HA-5825 - 3/8” x 25’ I.D. air hose assembly with fittings
HA-7325 - 3/8” x 25’ I.D. fluid hose assembly with fittings
JGHV Spray Gun
KB Cup
TLC Cup &Regulator
QMGT/QMSTPressure Tank
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted24
Spray Guns-Packages-Accessories
FLHVLP-1 Outfit Consists of:(1) JGHV-531-46FF spray gun of choice(1) KB-555 2 quart aluminum remote pressure cup(1) KB-4004 6 ft. hose set with fittings
FLHVLP-2 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-545-SS 2 quart Stainless Steel remote pressure
cup(1) KB-4004 6 ft. hose set with fittings
**FLHVLP-3 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-555 2 quart aluminum remote pressure cup(1) KB-4006 6 ft. hose set with fittings
FLHVLP-4 OutfitConsists of:(1) JGHV-531-46FF HVLP spray gun of choice(1) KB-545-SS 2 quart Stainless Steel remote pressure
cup(1) KB-4004 4 ft. hose set with fittings
** 4940-01-363-6937-FLHVLP-613 Outfit same asFLHVLP-3 different cup
FLHVLP-5 Outfit Consists of:(1) QMGT 2 gallon galvanized ASME pressure tank(1) Double regulation(1) Air Motor and agitator(1) Disposable liner(1) JGHV-531-46 FF HVLP spray gun of choice25 ft. of air hose with fittings25 ft. of fluid hose with fittings
FLHVLP-6 Outfit Consists of:(1) QMST 2 gallon stainless steel ASME pressure tank(1) Double regulation(1) Air Motor and agitator(1) Disposable liner(1) JGHV-531-46 FF HVLP spray gun of choice25 ft. of air hose with fittings25 ft. of fluid hose with fittings
*FLHVLP-7 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun(1) TLC-576 attached 1 quart pressure cup(1) KK-4980 pressure regulator
FLHVLP-8 Outfit Consists of:(1) JGHV-531-46FF HVLP spray gun(1) TSC-591 Stainless Steel attached pressure cup(1) KK-4980 pressure regulator
All outfits may be modified to suit your needs.Other model HVLP spray guns and
ASME pressure tanks available.
* 4940-01-363-6938 - FLHVLP-605 Outfit same asFLHVLP-7
Note: Model JGHV-531-46FF tested/verified ETV/EPA.See WWW.EPA.GOV/ETV
Spray Equipment Packages(fully assembled)
25
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Spray Guns-Packages-Accessories
Fluid Strainers and Equipment
Solvent SaversTM Hose / Gun CleanersSimple, easy-to-use cleaners speed up
equipment cleaning and save solvent(up to 86% savings!), which reducesV.O.C. emissions. Operate withcompressed air. Provide finely atomizedblast of solvent traveling through fluid
passages of spray guns, hoses, etc.Metering permits varying air/solventmix. Equipped with safety valve. 1/4"NPS (M) air and 3/8" NPS (M) fluidconnections.
Solvent Savers™ Hose/Gun CleanersSHIP WT. MAX. WORKING MATERIAL CONSTRUCTION
PART NO. COMPUTER NO. CAPACITY (LBS.) PRESSURE (IN CONTACT W/FLUID)
*HD-503 180037 2 qt. 5 50 psi Aluminum, nickel plated brass,
Teflon and Thiokol gasket
*QMGZ-5200 2 gal 42 110 psi Galvanized steel, aluminum,
nickel plated brass, Teflon &
Thiokol gaskets, polyethylene
tank liner
QMSZ-5200 2 gal. 38 110 psi 300 grade stainless steel, nickel
plated brass, Teflon & Thiokol
gaskets, polyethylene tank liner
*Note: Not suitable for use with chlorinated solvents, such as 1,1,1 trichloroethylene or methylenechloride. Specify QMSZ type stainless steel when chlorinated solvents are used.
VS-531 VS-532 PLH-MF-6-XX VS-506 VS-534
Fluid Strainers
STRAINER MAX. WORKING INLET OUTLET WETTED SCREEN MESH MICRON
STRAINER TYPE PART NO. PRESSURE THREADS THREADS PARTS PART NO. SIZE SIZE
Gun Mounted StrainersVS-531 300 3/8"NPS(M) 3/8"NPS(F) CS 31144-310-K10 100 149
VS-532 300 3/8"NPS(M) 3/8"NPS(F) PB VS-58-K10 100 149Swivel
In-Line StrainerVS-534 300 3/8"NPS(F) 3/8"NPS(M) SS VS-58-K10 100 149
Swivel
SS = Stainless Steel PB = Plated Brass CS = Carbon Steel
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted26
Tanks and Cups
BUILT TO
A.S.M.E.STANDARDS
Approved 2, 5, 10, 15 gallon sizes.Maximum working pressure 110 psi.QMG Tanks contain aluminum and
are not suitable for halogenatedhydrocarbons.
Contact Fluid-Air Products Inc.for more information.
Approved for5, 10 and 15 gallon sizes.
CRN REGISTERED (CANADA)
QMG Galvanized and QMS Stainless SteelTank Specifications
QMG Galvanized Tank ConstructionShell Zinc plated steel, 12 gauge (.105" thick)Lid Zinc plated steel, 3/16" thickAgitator Shaft Zinc plated steelAgitator Paddles Glass filled nylonShaft Seal Thiokol and stainless steelAir Manifold Zinc plated steelFluid Tube Galvanized steelFluid Valve Nickel Plated BrassTop Outlet Fitting Galvanized steelMaximum Working Pressure 110 PSI
Tank Dimensions/CapacitiesQMG Galvanized and QMS Stainless Steel
TANK SIZE ACTUAL CAPACITY (GAL.) INSIDE DIA. INSIDE HT. OVERALL HT.
2-Gal. 2.8 9 1/2" 9 1/2" 13 13/16"5-Gal. 10.8 14" 16" 20 5/16"
10-Gal. 12.7 14" 19 1/16" 23 3/8"15-Gal. 19.8 14" 29 1/16" 33 3/8"
Tank PortsQMG Galvanized and QMS Stainless Steel
Top Fluid Outlet 3/8 NPS(M) Bottom Fluid Outlet Plug 3/4 NPT Air Inlet 1/4 NPS(M) Air Outlet 1/4 NPS(M)
Shipping WeightsQMG Galvanized and QMS Stainless Steel
Tanks TANK CAPACITY SHIP. WT.* (LBS.)
2-Gal. 405-Gal. 85
10-Gal. 9515-Gal. 112*Note: Shipping weights may vary depending on weight ofagitator.
QMS Stainless Steel Tank ConstructionShell 304 stainless steel, 14 gauge (.075" thick)Lid 304 stainless steel, 3/16" thickAgitator Shaft 303 stainless steelAgitator Paddles Glass filled nylonShaft Seal Thiokol and stainless steelAir Manifold Zinc plated steelFluid Tube 316 stainless steelFluid Valve 316 stainless steelTop Outlet Fitting 316 stainless steelMaximum Working Pressure 110 PSI
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 GravoisSt. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
27Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Tanks and Cups
QMG Galvanized Tank Specifications
*Direct drive motor included.**Crank may be replaced by optional air motor. See accessories.***Extra sensitive regulator/gauge included.
5 Gallon QMG Galvanized TanksAGITATOR REGULATOR/GAUGE
5 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
QMGT-5500 NONE QMS-4003 0 1QMGT-5510 NONE QMS-4006 1 1QMGT-5520 NONE QMS-4007 2 2QMGT-5502 QM-142** QMS-4003 0 1QMGT-5512 QM-142** QMS-4006 1 1QMGT-5522 QM-142** QMS-4007 2 2QMGT-5513 QS-5012 QMS-4006 1 1QMGT-5523 QS-5012 QMS-4007 2 2QMGT-5516 QSR-503 QMS-4006 1 1QMGT-5526 QSR-503 QMS-4007 2 2QMGT-5530 NONE QMS-4010*** 1 1QMGT-5533 QS-5012 QMS-4010*** 1 1QMGT-5540 NONE QMS-4022 1 1
15 Gallon QMG Galvanized TanksAGITATOR REGULATOR/GAUGE
15 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
QMGT-51500 NONE QMS-4003 0 1QMGT-51510 NONE QMS-4006 1 1QMGT-51520 NONE QMS-4007 2 2QMGT-51502 QM-142** QMS-4003 0 1QMGT-51512 QM-142** QMS-4006 1 1QMGT-51522 QM-142** QMS-4007 2 2QMGT-51513 QS-5012 QMS-4006 1 1QMGT-51523 QS-5012 QMS-4007 2 2QMGT-51516 QSR-503 QMS-4006 1 1QMGT-51526 QSR-503 QMS-4007 2 2
QMGT-51530 NONE QMS-4010*** 1 1QMGT-51533 QS-5012 QMS-4010*** 1 1
10 Gallon QMG Galvanized TanksAGITATOR REGULATOR/GAUGE
10 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
QMGT-51000 NONE QMS-4003 0 1QMGT-51010 NONE QMS-4006 1 1QMGT-51020 NONE QMS-4007 2 2QMGT-51002 QM-142** QMS-4003 0 1QMGT-51012 QM-142** QMS-4006 1 1QMGT-51022 QM-142** QMS-4007 2 2QMGT-51013 QS-5012 QMS-4006 1 1QMGT-51023 QS-5012 QMS-4007 2 2QMGT-51016 QSR-503 QMS-4006 1 1QMGT-51026 QSR-503 QMS-4007 2 2QMGT-51030 NONE QMS-4010*** 1 1QMGT-51033 QS-5012 QMS-4010*** 1 1
QMGT-5200 NONE QMS-4030 0 1QMGT-5210 NONE QMS-4006 1 1QMGT-5220 NONE QMS-4007 2 2QMGT-5201 QMG-416* QMS-4003 0 1QMGT-5211 QMG-416* QMS-4006 1 1QMGT-5221 QMG-416* QMS-4007 2 2QMGT-5202 QM-142** QMS-4003 0 1QMGT-5212 QM-142** QMS-4006 1 1QMGT-5222 QM-142** QMS-4007 2 2QMGT-5213 QS-5012 QMS-4006 1 1QMGT-5223 QS-5012 QMS-4007 2 2QMGT-5216 QSR-503 QMS-4006 1 1QMGT-5226 QSR-503 QMS-4007 2 2QMGT-5230 NONE QMS-4010*** 1 1QMGT-5231 QMG-416* QMS-4010*** 1 1
AGITATOR REGULATOR/GAUGE
2 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
2 Gallon QMG Galvanized Tanks
Example: QMG T - 5 -
Ordering Information
Tank Size2 = 2-Gal. 5 = 5-Gal.10 = 10-Gal. 15 = 15-Gal.
Product Identification
Completely Factory Assembled
T = Top Fluid Outlet
Galvanized
Type of Agitation0 = None 1 = Direct Drive (2-Gal. Only)
2 = Hand 3 = QS-5012 (standard) 6 = QSR-503 (reciprocating)
Type of Regulation0 = None1 = One Regulator2 = Two Regulators
3 = Extra-Sensitive4 = One Regulator, Plated (select 2, 5-Gal. only)5 = Two Regulators, Plated (select 2, 5-Gal. only)
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted28
Tanks and Cups
10 Gallon QMS Stainless Steel TanksAGITATOR REGULATOR/GAUGE
10 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
QMST-51000 NONE QMS-4003 0 1QMST-51010 NONE QMS-4006 1 1QMST-51020 NONE QMS-4007 2 2QMST-51002 QM-142** QMS-4003 0 1QMST-51012 QM-142** QMS-4006 1 1QMST-51022 QM-142** QMS-4007 2 2QMST-51013 QS-5012 QMS-4006 1 1QMST-51023 QS-5012 QMS-4007 2 2QMST-51016 QSR-503 QMS-4006 1 1QMST-51026 QSR-503 QMS-4007 2 2QMST-51030 NONE QMS-4010*** 1 1QMST-51033 QS-5012 QMS-4010*** 1 1
QMS Stainless Steel Tank Specifications
*Direct drive motor included.**Crank may be replaced by optional air motor. See accessories.***Extra sensitive regulator/gauge included.
Example: QMS T - 5 -
Ordering Information
Tank Size2 = 2-Gal. 5 = 5-Gal.10 = 10-Gal. 15 = 15-Gal.
Product Identification
Completely Factory Assembled
T = Top Fluid Outlet
Stainless Steel
Type of Agitation0 = None 1 = Direct Drive (2-Gal. Only)
2 = Hand 3 = QS-5012 (standard) 6 = QSR-503 (reciprocating)
Type of Regulation0 = None1 = One Regulator2 = Two Regulators
3 = Extra-Sensitive4 = One Regulator, Plated (select 2, 5-Gal. only)5 = Two Regulators, Plated (select 2, 5-Gal. only)
2 Gallon QMS Stainless Steel TanksAGITATOR REGULATOR/GAUGE
2 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
QMST-5200 NONE QMS-4003 0 1QMST-5210 NONE QMS-4006 1 1QMST-5220 NONE QMS-4007 2 2QMST-5201 QMS-430* QMS-4003 0 1QMST-5211 QMS-430* QMS-4006 1 1QMST-5221 QMS-430* QMS-4007 2 2QMST-5202 QM-142** QMS-4003 0 1QMST-5212 QM-142** QMS-4006 1 1QMST-5222 QM-142** QMS-4007 2 2QMST-5213 QS-5012 QMS-4006 1 1QMST-5223 QS-5012 QMS-4007 2 2QMST-5216 QSR-503 QMS-4006 1 1QMST-5226 QSR-503 QMS-4007 2 2QMST-5230 NONE QMS-4010*** 1 1QMST-5231 QMS-430* QMS-4010*** 1 1
15 Gallon QMS Stainless Steel TanksAGITATOR REGULATOR/GAUGE
5 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
QMST-51500 NONE QMS-4003 0 1QMST-51510 NONE QMS-4006 1 1QMST-51520 NONE QMS-4007 2 2QMST-51502 QM-142** QMS-4003 0 1QMST-51512 QM-142** QMS-4006 1 1QMST-51522 QM-142** QMS-4007 2 2QMST-51513 QS-5012 QMS-4006 1 1QMST-51523 QS-5012 QMS-4007 2 2QMST-51516 QSR-503 QMS-4006 1 1QMST-51526 QSR-503 QMS-4007 2 2QMST-51530 NONE QMS-4010*** 1 1QMST-51533 QS-5012 QMS-4010*** 1 1
5 Gallon QMS Stainless Steel TanksAGITATOR REGULATOR/GAUGE
5 GAL. TANK DRIVE FURNISHED ASSEMBLY FURNISHED GAUGE
PART NO. PART NO. PART NO. QTY. QTY.
QMST-5500 NONE QMS-4003 0 1QMST-5510 NONE QMS-4006 1 1QMST-5520 NONE QMS-4007 2 2QMST-5502 QM-142** QMS-4003 0 1QMST-5512 QM-142** QMS-4006 1 1QMST-5522 QM-142** QMS-4007 2 2QMST-5513 QS-5012 QMS-4006 1 1QMST-5523 QS-5012 QMS-4007 2 2QMST-5516 QSR-503 QMS-4006 1 1QMST-5526 QSR-503 QMS-4007 2 2QMST-5530 NONE QMS-4010*** 1 1QMST-5533 QS-5012 QMS-4010*** 1 1
29Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Tanks and Cups
Tank AccessoriesQMG Galvanized and QMS Stainless Steel
Tank Inserts With HandleStainless steel insert for use inside
tank. Removable insert with handle iseasily portable – eliminates need tocarry entire tank to paint-fill area.Also protects tank and material. (Maybe used in tanks with agitator.) Direct Drive Agitator
Air-powered direct drive agitatorassembly with 1/4 hp air motor anda three-bladed propeller to keepmaterials mixed in suspension, evenhigh solids. Use on two-gallon QMGmodels. Shipping weight 8 lbs.
QMG-416 (for use with QMG)
QMS-430 (for use with QMS)
Paint Drum Agitator DriveQS-5003
For use with paint drums havingbuilt-in agitators. Powerful variablespeed air motor. Requires 5 to 8 CFMof air for 50 RPM of agitator;adjustable from 10 RPM up. Airconnection 1/4" NPS(M). Includescouplings to fit 7/16" and 1/2" agitatorshafts. The mounting adapter fits both1-1/2" and 2" threads. Shippingweight: 15 lbs.
Hand Crank QM-142For manual operation of agitator.
Shipping weight: 1 lb.Dual Fluid Outlet KitAllows two spray guns to be supplied
by a single pressure tank. Shippingweight: 3/4 lb.
QMG-443 (for use with QMG)
QMS-454 (for use with QMS)
Tank Inserts TANK CAPACITY PART NO. SHIP. WT.
5-Gal. QMS-427 10 lbs.
10-Gal. QMR-410 16 lbs.
15-Gal. QM-4245 19 lbs.
Polyethylene LinersSemirigid tank liners of tough,durable, high density polyethylenewith “ANTI-STAT” additive whichminimizes static electricity buildupfrom the friction of shipping andhandling liners. May be reused. (Canbe used with optional agitators.)
Air Motor DriveQS-5012
Standard duty, smooth running withgear reducer, 1/4 hp, 15:1 ratio, 20 to120 RPM. Includes throttling valve,fittings, and hose for connection to airsupply on tank lid. Air consumption:Approximately 6 CFM at 50 RPM.Shipping weight: 11 lbs.
Note: 170°F Max Temperature
Polyethylene Liners TANK CAPACITY PART NO. KIT OF SHIP. WT.
2-Gal. PT-52-K10 10 7 lbs.2-Gal. PT-52-K80 80 29 lbs.5-Gal. PTL-406-K20 20 20 lbs.
10-Gal. PTL-410-K8 8 12 lbs.
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted30
Tanks and Cups
Air Regulator Assembly Kits
Part No.
QMS-436One gauge, one regulator. Convertssingle regulation to dual.
QMS-4003One gauge, no regulator. Indicatespressure in tank. Wt: 2 lbs.
QMS-4006One gauge, one regulator. Regulatesand indicates tank pressure. Wt: 4 lbs.
QMS-4007Two gauges, two regulators. Controlstank pressure and atomization airpressure to gun. Wt: 6 lbs.
QMS-4010One extra sensitive gauge, oneextra sensitive regulator. Usewith electrostatic spray or otherapplications requiring extremelysensitive, non-fluctuating, lowpressure control.Wt: 5 lbs. Max. 30 lbs. pressure.
QMS-4022One specially-plated gauge andregulator. Regulates and indicates tankpressure. Wt: 4 lbs.
QMS-4023Two specially-plated gauges andregulators. Controls tank pressure andatomization air pressure to gun.Wt: 6 lbs.
Tank AccessoriesQMG Galvanized and QMS Stainless Steel
Chemical CompatibilityWith Gasket Materials
E: Excellent G: Good C: ConditionalU: Unsatisfactory X: No Test Data
The chemical compatibility shown here is meantfor initial guidance only. Actual concentrationsand conditions greatly affect corrosionresistance.
GASKET MATERIAL
SBR RUBBER TEFLON THIOKOL
Acetone U E C Carbon Tetrachloride U E C Chlorinated Solvents U E C Glycerine E E C Lacquers U E C Linseed Oil U E E Methyl Ethyl Ketone U E E Mineral Oil U E C Tannic Acid G E G Toluene (Toluol) U E G Trichlorethylene U E G Turpentine U E E Varnish U E X *Waterborne Coatings E E E Xylene (Xylol) U E ENote:*Check co-solvent used in waterborne material
for compatibility.
GASKET 2-GAL. 5, 10, AND 15-GAL.
MATERIAL PART NO. PART NO.
SBR Rubber QM-1008
Teflon QMS-52 QMS-51
Thiokol* QMS-80-K2 QM-1458
Optional Agitator Drive AccessoriesReplacement Units. Motor drive or crank must be ordered separately.
STANDARD RECIPROCATING
DESCRIPTION GALVANIZED STAINLESS MOTOR DRIVE MOTOR DRIVE HAND CRANK
PART NO. PART NO. SHIP WT. PART NO. PART NO. PART NO.
2-Gal. Direct Drive Agitator Assembly QMG-416 QMS-430 8 lbs. includes motor* n/a n/a 2-Gal. Hand Agitator less drive motor QMG-417 QMS-431 7 lbs. QS-5012 QSR-503 QM-14 5-Gal. Agitator Assembly less drive motor QMG-418 QMS-432 8 lbs. QS-5012 QSR-503 QM-142 10-Gal. Agitator Assembly less drive motor QMG-419 QMS-433 9 lbs. QS-5012 QSR-503 QM-142 15-Gal. Agitator Assembly less drive motor QMG-420 QMS-434 10 lbs. QS-5012 QSR-503 QM-142
Lid GasketsReplacements / Options
DeVilbiss offers several lid gasketalternatives to be used in place of thestandard Thiokol® gasket. Refer tochemical compatibility with gasketmaterials chart at right. (Note: ThiokolGaskets are standard on all factoryassembled QMG and QMS tank models.)
* 2-gal. direct drive agitator assembly includes standard air motor.
Shipping Weightsfor QMG and QMS Accessories
ADD FOR*AGITATOR/ AGITATOR/
TANK AGITATOR/ QS-5012 QSR-503
CAPACITY CRANK AIR MOTOR AIR MOTOR
2-Gal. 8 lbs. 18 lbs. 22 lbs.5-Gal. 9 lbs. 19 lbs. 23 lbs.
10-Gal. 10 lbs. 20 lbs. 24 lbs.15-Gal. 11 lbs. 21 lbs. 25 lbs. *Example: A 15-gallon tank with optionalQS-5012: shipping weight 112 + 21 lbs. =133 lbs.
*Standard on all factory-assembled QMGand QMS tank models.
Bottom Outlet Conversion KitFittings which allow standard top outlet tank to feed from bottom by removing plug in
bottom port. All wetted parts galvanized steel for QMG models.TANK GALVANIZED STAINLESS STEEL
CAPACITY PART NO. PART NO. SHIP WT.
2-Gal QMG-421 QMS-435 3 lbs. 5, 10, 15-Gal. QMG-428 QMS-443 4 lbs.
31Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Tanks and Cups
Pressure and Suction Feed Cups
Gravity Feed CupsMade of strong, lightweight material
for durability. Features a “dry check”device integral with cup lid to avoidspillage from vent hole.
KGP-509-1 - 8-oz. Cup (Nylon)
GFC-501 - 20-oz. Cup (Delrin)
Polyethylene Suction CupTGS-503
8-oz. cup size. Combines engineeredresin lid with translucent polyethylenecup – liquid level visible. Molded-ingraduations for mixing ratios.Lightweight and easy to clean.Nonstaining. Includes cup closure.Compatible with all solvents. Use withEGA-502, EGHV-530 or any suctionfeed gun with 1/4" NPS threads.
Aluminum Suction CupsAluminum suction cups incorporate a
two-position special lid design – oneas drip-free cup or the other asconventional suction feed cup. Smoothmetal surfaces make cleanup andchanging paint fast and easy. Use withall suction feed spray guns.
TGC-545 - Quart Capacity Suction Cup
TGC-536 - Pint Capacity Suction Cup
Low Pressure Cup for HVLPTLC-576
Aluminum, one-quart, lowpressure cup for HVLP applications.Teflon®-lined for fast, easy cleaning.Solvent-resistant check valve.Requires KK-4980 for cup airregulation. (Order separately)
Teflon®-Lined Suction CupTLC-555
Aluminum, one-quart cup featuringTeflon® lining for fast, easy cleaningand reduced color contamination.Drip-free lid design has two-positionvalve which allows for operation as“drip-free” cup or as conventionalsuction cup. Use with all suction feedspray guns.
Stainless Steel CupsOne-quart cups made from 300
series stainless steel, designed for usewith waterbased materials and exemptsolvents. The .030" wall thicknessmakes it more durable thancompetitive cups, yet still lightweight.And the fluid tube is stainless steel foradded durability and corrosionresistance.
TSC-591 - HVLP Low PressureFeed Cup. Requires KK-4980 for cupair regulation (order separately)
TSC-595 - Suction Feed Cup
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted32
Tanks and Cups
For use with both conventional airspray systems and HVLP systems, theKB II series, two-quart cups feature a“pistol grip” carrying handle, and rightor left-handed design for comfort andease of handling. An easy-open lid andwide cup mouth allow for fast fillingand cleanup. KB Series cups alsofeature a solvent resistant check valveand a wide base for greater stability.
KB series cups are ideal for handlingheavier viscosity materials, higher flowrates, as well as low fluid flow rates of10 ounces per minute or less. Fluidpressure range of 2-30 psi. Order air/fluid hose assemblies separately.
KB-4004 - 4-foot hose length.
KB-4006 - 6-foot hose length mostcoating materials and solvents.
Pressure and Suction Feed CupsCOMPLETE CUP CONNECTION APPROX. SHIP
ASSEMBLY THREAD SIZE CUP AND COVER CUP ONLY WT/ COMPLETE
PART NO. CAPACITY MATERIAL FLUID AIR ASSEMBLY PART NO. CUP AND LID
Pressure FeedKB-555 2 qt. Aluminum 3/8"NPS(M) 1/4" NPS(M) — KB-422 3 lbs. 14 oz.
KB-545-SS 2 qt. Stainless Steel 3/8"NPS(M) 1/4" NPS(M) — KB-442 5 lbs. 2 oz.
TSC-591 1 qt. Stainless Steel 3/8"NPS(M) — — TSC-400 20 oz.
TLC-576 1 qt. Aluminum w/Teflon® Lining 3/8"NPS(F) — TLC-401 18 oz.
Suction FeedTGC-536 6 oz. Aluminum 3/8"NPS(F) — — TGC-432 12 oz.
TGC-545 1 qt. Aluminum 3/8"NPS(F) — — KR-428-2 18 oz.
TGS-503 8 oz. Polyethylene 1/4"NPS(F) — TGS-406 3 oz
TLC-555 1 qt. Aluminum w/Teflon® Lining3/8"NPS(F) — TLC-401 18 oz.
TSC-595 1 qt. Stainless Steel 3/8"NPS(M) — — TSC-400 20 oz.
Gravity FeedKGP-509-1 8 oz. Nylon 3/8"BSP(M) — — — 3 oz.
KGP-510-1 20 oz. Delrin 3/8"BSP(M) — — –– 6 oz.* Use with GFG and GFHV guns only.** Order KK-4980 Air Regulator Kit in addition to cup.
KB Series Pressure Feed Cups
Aluminum CupKB-555
DeVilbiss KB Aluminum modelcups are compatible with most coatingmaterials and solvents.
Stainless Steel CupKB-545-SS
DeVilbiss KB Stainless Steelmodel cups are designed for usewith waterbornes, halogenatedhydrocarbons and other corrosivematerials.
KK-5051 Disposable CupLiner Kit includes20 liners, 20 lids and 3 rings
33
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
CleanAir Centrifugal Filter-Regulator Units
Excellent for eliminating moistureand dirt from an air supply, DeVilbissCleanAir centrifugal units supplycleaner, drier air to each spray gun in asystem. This cleaner air can alsoincrease the life of pneumatic tools.
• Filters out water and oil aerosols anddirt particulates to 5 microns.
• Ideal for most spray applications, airtools and equipment.
• Water droplets collected in the bowlare removed by an automatic drain(standard feature). No need tomanually drain.
Quick-release filter bowl and spin-off5-micron filter element allow one-minutefilter changes without tools. Pressure dropsare minimized by large air inlet and outletand large internal air passages.
HFRL-511
HAF-502 HAF-503 HFRL-508 HFRL-509
• Prevents tampering or unauthorized air regulatoradjustment
• Where 10 PSI max. HVLP air cap pressures isregulated, can prevent noncompliance andpotential fines
• Assures proper atomization and fluid pressure forconsistent spray performance
• Used with DeVilbiss “HAR” type air regulators(some competitive models also)
• Easy to install
HAR-400 REGULATOR LOCKOUT ACCESSORY 3/16” Allen Slot Locknut
Sleeve & LockAssy.
AdjustmentScrew
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted34
Clean Air Filtration-Accessories
CleanAir Centrifugal Filter-Regulator Units
Accessories• Mounting Bracket Assembly Kits
For HAF-502 air filter and HFRL-508regulator; order HAF-407.For HAF-503 air filter, and HFRL-509and HFRL-511 regulators, orderHAF-408.
Centrifugal Air Filter UnitsPART NO. HAF-502 HAF-503
Filtering Capacity (micron) 5 5
Flow Rate (CFM) 100 @ 90 psi 150 @ 90 psi
Max. Inlet Pressure (psi) 150 150
Max. Operating Temp. 150oF 150oF
Inlet Port Size 1/2" NPT (F) 3/4" NPT (F)
Outlet Port Size 1/2" NPT (F) 3/4" NPT (F)
Bowl Capacity 17 oz. 34 oz.
Shipping Weight 1 lb. 7 oz. 3 lbs. 1 oz.
Service Bulletin SB-6-146 SB-6-148
Tornado-like swirling action removes moisturewhich collects in the baffled “quiet zone.”The reusable 5-micron filter catches smallerimpurities. Accumulated liquid is carriedaway by the automatic drain.
Airinlet
Centrifugal Filter-Regulator UnitsPART NO. HFRL-508 HFRL-509 HFRL-511
Filtering Capacity (micron) 5 5 5
Flow Rate (CFM) 50+ 80+ 120+
Max. Inlet Pressure (psi) 150 150 150
Regulated Pressure Range (psi) 0 - 125 0 - 125 0 - 125
Max. Operating Temp. 150oF 150oF 150oF
Inlet Port Size 1/2" NPT (F) 3/4" NPT (F) 3/4" NPT (F)
Regulated Outlets (w/ball valve) (1) 1/4" NPS (M) (2) 1/4" NPS (M) (4) 1/4" NPS (M)
Non-Regulated Outlets (w/ball valve) (1) 1/4" NPS (M) (1) 1/4" NPS (M) (1) 1/4" NPS (M)
Bowl Capacity 17 oz. 34 oz. 34 oz.
Air Filter Included HAF-502 HAF-503 HAF-503
Quality Air Regulators/Model (1) HAR-506 (1) HAR-507 (2) HAR-507
Air Gauges (0 - 100 psi) 1 1 2
Air Gauges (0 - 160 psi) 1 1 1
Shipping Weight 9 lbs. 15 lbs. 18 lbs.
Service Bulletin SB-6-146 SB-6-148 SB-6-148
Flexibletubing
Automaticdrain
Quietzone
Baffle
Reversible5-micronfilterTornado
swirl ring
• Filter Element Kits (5-Micronreusable)For HAF-502 air filter and HFRL-508regulator; order HAF-6.For HAF-503 air filter, and HFRL-509and HFRL-511 regulators, order HAF-15.
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 Gravois Rd.St. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
35
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
CleanAir Coalescer Filter-Regulator Units
HFRL-513
CleanAir coalescer filters removewater, dirt and oil from the systemdown to .01 micron. DeVilbisscoalescer filter units are designedwith a quick-release bowl andspin-off element for filter changeswithout tools. In addition, a filter-change indicator alerts the operatorwhen the element requires changing.
• Borosilicate glass microfiber filter isengineered for high flow, highefficiency, quick change and lowpressure drop.
• Ideal for most spray applications,especially where oil aerosols maybe a problem.
• Automatic bowl drain and 6' hoseeliminate oil and water buildup(standard feature). No need tomanually drain.
The HAF-508 is the coalescer filteronly. In combination with thecentrifugal filter, there are threechoices – the HAF-509 non-regulatedunit and the two regulated models –HFRL-512 and HFRL-513.
HAF-509 HFRL-512
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted36
Clean Air Filtration-Accessories
CleanAir Coalescer Filter-Regulator Units
Accessories• Mounting bracket assembly kit is
available; order HAF-408.
• Centrifugal filter element kit hasreusable 5-micron filter; orderHAF-15.
• Coalescer filter element kit has.01-micron filter; order HAF-38.
Centrifugal-Coalescer Filter UnitsHAF-508 HAF-509
NON-REGULATED MODELS COALESCER* CENTRIFUGAL& COALESCER
Centrifugal Filtering Capacity (micron) 5 5
Coalescer Filtering Capacity (micron) .01 .01
Flow Rate (CFM) 150 @ 90 psi 150 @ 90 psi
Max. Inlet Pressure (psi) 150 150
Max. Operating Temp. 150oF 150oF
Inlet Port Size 3/4" NPT (F) 3/4" NPT (F)
Outlet Port Size 3/4" NPT (F) 3/4" NPT (F)
Bowl Capacity 34 oz. 34 oz.
Shipping Weight 3 lbs. 2 oz. 6 lbs. 3 oz.
Service Bulletin SB-6-148 SB-6-148
Pre-filter support fabric prevents mediamigration, increasing element life. Stainlesssteel screens provide fail-safe protection againstaccidental shock loads and high pressure dropsin either direction. Anti re-entrainment barrierprevents liquid carryover, even in shockconditions, and is compatible with mineral andsynthetic lubricants. A – Easy-fit captive O-ring
Coalescer-Filter Regulator UnitsREGULATED MODELS HFRL-512 HFRL-513
Centrifugal Filtering Capacity (micron) 5 5
Coalescer Filtering Capacity (micron) .01 .01
Flow Rate (CFM) 80+ 120+
Max. Inlet Pressure (psi) 150 150
Regulated Pressure Range (psi) 0 - 125 0 - 125
Max. Operating Temp. 150oF 150oF
Inlet Port Size 3/4" NPT (F) 3/4" NPT (F)
Regulated Outlets (w/ ball valve) (2) 1/4" NPS (M) (4) 1/4" NPS (M)
Non-Regulated Outlets (w/ ball valve) (1) 1/4" NPS (M) (1) 1/4" NPS (M)
Bowl Capacity 34 oz. 34 oz.
Quality Air Regulators/Model (1) HAR-507 (2) HAR-507
Air Gauges (0 - 100 psi) 1 2
Air Gauges (0 - 160 psi) 1 1
Shipping Weight 18 lbs. 2 oz. 21 lbs. 2 oz.
Service Bulletin SB-6-148 SB-6-148
* HAF-508 coalescer filter should be used in conjunction with a centrifugal type filter to removethe majority of water, oil and dirt, prior to the coalescer filter.
A
B
C
D
E
G
F
B – Corrosion-resistant end capsC – Pre-filter support fabricD – Stainless steel support screensE – Anti re-entrainment barrierF – Borosilicate glass microfiber filter
G – High-strength epoxy sealant
37
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
CleanAir Three-Stage Desiccant Unit
The three-stage desiccant unitprovides the ultimate in clean dry air.First stage centrifugal filter removesparticulates to 5 microns. Stage twocoalescer filters down to .01 micron.Third stage desiccant removesremaining water vapor to a dew pointof -40oF.
• Ideally suited for low to mediumproduction.
• DAD-500 air-drying system includesthree filtering units, as well as a wallmount bracket and desiccant filterchange indicator.
• Centrifugal and coalescer unitsinclude automatic bowl drain(standard feature). No need tomanually drain.
DAD-500 Desiccant Air Drying SystemDAD-500 HAF-502 HAF-505 HAR-506
AIR DRYING CENTRIFUGAL COALESCER REGULATORDESICCANT SYSTEM UNITS SYSTEM* FILTER ONLY FILTER ONLY** ONLY
Air Inlet 1/2" NPT (F) 1/2" NPT (F) 1/2" NPT (F) 3/8" NPT (F)
Air Outlet 1/2" NPT (F) 1/2" NPT (F) 1/2" NPT (F) 1/4" NPT (F)(3 ea)
Max. Operating Pressure (psi) 150 150 150 150
Replacement Filters/Desiccant DAD-1 HAF-6 HAF-28 —
Service Bulletin SB-6-156 SB-6-146 SB-6-152 SB-6-144
Air Flow Capacity (cfm) 25 100 55 40
DAD-500
* Includes HAF-502, HAF-505 and HAR-506.** Has filter-change indicator to alert operator when element requires changing.
Five Easy Ways to Order from Fluid-Air Products Inc.
CALLToll-Free
800-365-7565to order
MAILyour order
12834 Gravois Rd.St. Louis, MO 63127
FAXyour order
314-729-7099
E-MAILyour order
WEBSITEVisit our site
www.fluidair.comand link to
www.gsa.govfor on-line ordering
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted38
Clean Air Filtration-Accessories
HAF-507-K12 WhirlWind In-Line FilterMAXIMUM
HOUSING OPERATING OPERATING PRESSURE DROP LIQUID SERVICEMATERIAL PACKAGING THREADS PRESSURE TEMPERATURES @ 80 PSI w/ 20 SCFMCONTAMINANT BULLETIN
Solvent-resistant 12 filters 1/4" NSP (M) inlet 125 psi 50oF - 110oF 2 psi 1.5 fl. oz. SI-8-10-1Delrin® plastic per dispenser carton 1/4" NSP (F) inlet
MAX. REGULATED MAX AIR MAX
CAPACITY PRESS.RANGE INLET PRESS. OPERATING DIMENSIONS WEIGHT MAIN AIR INLET MAIN LINE OUTLET REGULATED OUTLETS
MODEL CFM PSI PSI TEMP OF H" X W" LBS. PORT SIZE PORT SIZE PORT SIZE
HAR-501* 15 0 - 20 250 120o 6 x 4-1/2 2-1/4 1 3/8" NPT (F) - - 1 3/8" NPT (F)HAR-535 40 0 - 125 250 120o 4-7/8 x 2-3/8 1-1/8 1 3/8" NPT (F) 1 1/4" NPT (F) 1 3/8" NPT (F)HAR-555 40 0 - 125 250 120o 4-7/8 x 2-3/8 1-1/8 1 3/8" NPT (F) 2,4 1/4" NPT (F) 1 1/2" NPT (F)HAR-507 60 0 - 125 300 120oo 4-7/8 x 3 1-1/2 1 3/8" NPT (F) - - 3 1/4" NPT (F)
WhirlWind In-Line Filter
The WhirlWind disposable in-linefilter attaches to the base of the spraygun or air tool to remove anyremaining water, oil, dirt and rustfrom the air line. This high-quality,high-flow, solvent-resistant air filterhas a very low pressure drop and hasa floating filter that automaticallyadjusts for changing air conditions.
• Air is swirled to trap droplets, thenfiltered to absorb remainingparticulates.
• Multilayer design extends life, so unitlasts up to 40% longer than other filters.
• Perfect for use with HVLP guns,WhirlWind provides 55% more air flowthan other filters.
HAF-507-K12
CleanAir Air RegulatorsHAR-502/505/535/555/556/557
Air RegulatorGeneral purpose regulators for line
takeoff use or as integral regulators onpumps, pressure tanks and other airoperated devices. Require separate trapor filter in air line to remove moistureor dirt.
• Unique three position, non-risingadjusting knob.
• Removable plug and cap.
• All metal body; durable Delrin® capand knob; Buna N diaphragm anddisc.
• Accurate regulator mechanismprovides precision air control.
• Self-relieving design.
• Both main line and regulated outletsavailable from same units.
HAR-501 Air RegulatorExtra Sensitive regulator for use
with precision control on pressure feedtanks or other dead-end applications.Can be used to control atomizationpressure for one spray gun.
• Self-relieving regulator.
• Tough, reinforced Buna N
diaphragm for extended service life.
• 100 mesh stainless steel strainer.
• Removable bottom plug for easyservice.
• Forged brass body and stainless steelor brass internal parts for longservice.
• High ratio of diaphragm surface toorifice area provides stable uniformregulation.
* Extra-sensitive regulator for precise control on pressure tanks and other dead-endapplications.
TM
HAR-505 HAR-501
39
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
Air Control Accessories
For accurate pressure readings,standard gauges are made fromrust-resistant materials and includeglass covered dials. Can be used inany location where conditions ofvibration or rough service exist.
GA-77 gauge is very accurate in lowpressure range and ideal for criticalpressure adjustments. Calibrated inounces from 0 to 10 lbs.; in poundsfrom 10 to 30 lbs.
GA Pressure GaugesMODEL SCALE (TYPE) THREAD DIAMETER INLET
GA-73 0 - 30 psi (A, F) 1/4" NPT (M) 2" BottomGA-77 0 - 30 psi (A, F) 1/4" NPT (M) 3-1/2" BottomGA-92 0 - 60 psi (A, F) 1/8" NPT (M) 1-1/2" BottomGA-288 0 - 160 psi (A, F) 1/4" NPT (M) 2" BottomGA-313 0 - 15 psi (A) 1/8" NPT (M) 1-1/2" BottomGA-316 0 - 160 psi (A) 1/4" NPT (M) 2" BackGA-333 0 - 100 psi (A, F) 1/4" NPT (M) 2" BottomGA-338 0 - 160 psi (A) 1/8" NPT (M) 1-1/2" Back
• HARG-510 is a precise, lightweightair regulator and gauge combination.Fits any professional spray gun;comfortable for left and right-handedpainters. Swivel adaptor allows fastinstallation, and a lockring securespressure settings to avoid interruptionsfor readjustments. Max. Air InletPressure: 400 psiOutlet Pressure Adjust. Range:5-100 psiGauge Port Size in Regulator:1/8" NPT (F)
• HAV-500 and HAV-501 are preciseair adjustment valves that controlpressure at the spray gun. Fits allprofessional spray guns. A swivel topallows for easy and fast installation.
• P-H-5516 air adjustment accessoryattaches directly to the spray gunair inlet. The large knurled knobadjusts air flow. Commonly used withspray guns, pressure tanks and pumps.
Air Adjusting ValvesGAUGE
MODEL AIR INLET AIR OUTLET NET WT. RANGE TYPE
HARG-510 1/4" NPS (M) 1/4" NPS (F) 10 oz. 0 - 160 psi Diaphragm(Nipple) (Swivel Adapter) Relieving
HAV-500 1/4" NPS (M) 1/4" NPS (F) (Swivel) 3.5 oz. n/a StraightHAV-501 1/4" NPS (M) 1/4" NPS (F) (Swivel) 5 oz. 0 - 160 psi w/ GaugeP-H-5516 1/4" NPS (M) 1/4" NPS (F) (Swivel) 3 oz. n/a Straight
Air ValvesMAX. OPERATING
MODEL DESCRIPTION PRESSURE MATERIAL
VA-527 3/8" NPS (M) x 3/8" NPT (M) 500 Stainless SteelVA-540 3/8" NPS (M) x 3/8" NPT (M) 500 BrassVA-541 1/4" NPS (M) x 3/8" NPT (M) 500 BrassVA-542 1/4" NPS (M) x 1/4" NPT (M) 500 Brass
HARG-510 HAV-501 HAV-500 P-H-5516
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted40
Clean Air Filtration-Accessories
Air VizorTM
Breathable Air Systems
The World’s Most Technologically AdvancedAir Supplied Respirator.
• Protects against isocyanate exposure.• Part of a complete breathable air system.*• NIOSH approved (TC 19C-0365) - meets OSHA
requirements.• Cool and comfortable.• Full lightweight face mask with excellent visibility.
- Ratchet adjustable headgear.- Detachable fabric face shield for excellent durability.- Peel-away face shield protectors improved to
reduce glare.- Detachable hair and neck cover.- Rigid face piece for better visibility over time.- Replaceable visor window for economical servicing.
• Easily accommodates prescription eyewear and beardedemployees.
• Disposable carbon filter and pre-set tamper proofregulator.- 1,000 hour carbon cartridge life- Filter change indicator
• Adjustable belt with quick fit buckle.• Quick connect between visor and waistbelt permits easy
removal of visor.• Air Vizor (MPV-625) includes:
- Full face mask- Belt-mounted filter and regulator- Breathing air tube
* Air VizorTM requires proper air line filtration and carbonmonoxide (CO) monitoring to complete an approvedsupplied air respirator. See next page for proper air linefiltration. A carbon monoxide (CO) monitor may bepurchased locally.
Breathable Air Systems
Belt # ofRegulator Breathable Visor Filtration
Order No. and Hood Air Covers Unit FiltrationModel No. Assembly Hose (30’) Included Included Description
165013 Yes No 2 None --------MPV-625
160019 Yes Yes 12 DAD-503 3-StageMPV-651 Filtration with
Desiccant AirDryer System
160020 Yes Yes 12 HAF-601 3-StageMPV-652 Filtration
System
160018 Yes Yes 12 DAD-502 DesiccantMPV-650 Retrofit
System
41
Order Toll-Free 800-365-7565Govt. Purchase Cards Accepted
Clean Air Filtration-Accessories
Air VizorTM
Breathable Air Filtration Units
DAD-503
• Converts shop air into clean, dry,
contaminant-free air for breathingsystems and spray operations.
• 5 micron particulate filter (Stage 1)
• .01 micron coalescing filter (Stage 2)• Charcoal filter for hydrocarbon and odor removal
(Stage 3)
• 28 CFM breathing air regulator• Desiccant system removes water vapor for spray
gun
• 60 CFM spray gun regulator• Automatic drains (Stages 1 and 2)
• Can be used with up to four Air Visors
• 1/2” NPT inlet
HAF-601
• Converts shop air into clean, contaminant-free air
for breathing systems and spray operations
• 5 micron particulate filter (Stage 1)• .01 micron coalescing filter (Stage 2)
• Charcoal filter for hydrocarbon and odor removal
(Stage 3)• 28 CFM breathing air regulator
• 60 CFM spray gun regulator
• Automatic drains (Stages 1 and 2)• Wall-mount bracket
• Can be used with up to four Air Vizors
• 1/2” NPT inlet
DAD-502
• Converts a DAD-500 into a breathing air source
• 5 minute installation. Mounts to top of desiccant
tank• Charcoal filter for hydrocarbon and odor removal
• 13 CFM breathing air regulator. Includes all
necessary fittings• Can be used with one Air Vizor