A Safety Handbook for Elementary and Makerspace Teachers
HEADS UP FOR SAFETY
Elementary
Makerspace Responsibilities
Safety in the class is everyone’s business. Following is a list of responsibilities as adapted from
the Workers’ Compensation Board in their WorksafeBC Online document entitled, “Safety on
the job is everyone’s business.”
Employer (School District/Administrator)
Provide a safe environment
Take action immediately when the worker or supervisor tells you about a potentially
hazardous situation
Initiate an immediate investigation into accidents
Provide adequate First Aid facilities and services
Provide personal protective equipment where required
Provide instruction for Maker Facilitator/teacher
Supervisor (Elementary/Maker Teacher)
Instruct students in safe work procedures
Keep records of safety tests
Correct unsafe acts and conditions
Employee (Student)
Know and follow safe procedures affecting your work
If you do not know, ask for training before you begin work
Work safely and encourage your classmates to do the same
Report any unsafe conditions to your teacher
Note: Students are not employees and, therefore, if injured, are not entitled to Workers’
Compensation Benefits.
HEADS UP FOR SAFETY
Due Diligence
Due diligence requires taking all reasonable steps to protect workers from harm. 'All reasonable steps' is based on the level of judgment and care that a person would reasonably be expected to do under the circumstances. An organization that actively manages health and safety and takes all reasonable steps to protect workers from harm is being duly diligent.
Due diligence requires that you:
Identify all workplace hazards
Implement all necessary preventive measures
Communicate appropriately to all necessary personnel
Steps to Being Duly Diligent
1
Be Aware
Ignorance is no defence.
2
Be Objective
Identify issues for your workplace using appropriately knowledgeable people.
3
Be Proactive
Develop a safety program that includes procedures, and practices to minimize risk from
hazards. Communicate these practices and ensure all workers are trained.
An active safety management approach — one that demonstrates due diligence — ensures
that workers are provided with valuable safety information, instruction and training. 4
HEADS UP FOR SAFETY
Elementary/Maker Teacher Tool Safety Checklist
It is expected a teacher using any of the tools below has been instructed by a Technology
Education trained teacher, and fully understands the use and safety of the tools prior to using
the tools with their class. Local School District Administration recognize that this document and
subsequent orientation/demonstrations are a minimum standard for working in
elementary/maker classroom environments.
Process:
Technology education teacher demonstrates proper techniques in tool use and tests for
understanding (written and demonstrated). Records kept by school district.
Appropriate safety precautions and personal protective equipment is used.
Teacher goes over tool procedures and demonstrates proper techniques to their class.
Teacher gives safety tests for each tool requiring testing.
Students must obtain 100% on every test. Students can make corrections to obtain this
mark. Tests must be given each year and retained if an accident occurs.
Tools that require attention to safety concerns:
Tool concern
Drill See safety procedure sheet and test
Jigsaw See safety procedure sheet and test
Handsaw Teeth on saw are sharp. Once saw is started into cut, fingers should be more than 2” away. Use slow, steady, full strokes of the saw to make cut. Clamp material down if it cannot be easily held down.
Hammer Be careful of nails flying once struck by hammer, this usually happens when it is first started into wood. Use a moderate, controlled swing.
Chisel Cutting edge is very sharp. Always have both hands on the chisel handle. Material must be clamped down. Always chisel away from yourself.
Utility Knife Recommend only the teacher use. Only extend small portion of the blade. Cut away from yourself. Be very observant of what is underneath cut. Be aware of cutting path.
Hot Glue Gun Easy to burn oneself. Only allow glue guns to be used in a specific location designated by teacher. Do not touch heating end of glue gun. Do not allow melted hot glue to come into contact with skin. If hot glue does stick to skin, run under cold water for 10 minutes or until it is easily removed. Do not pull glue off skin right away.
Block Plane The blade is sharp. Never test for sharpness with finger. Use a piece of wood. Be aware of the cutting blade path. Clamp material down.
Spoke Shave The blade is sharp. Never test for sharpness with finger. Use a piece of wood. Be aware of the cutting blade path. Clamp material down.
HEADS UP FOR SAFETY
Elementary/Maker Teacher Tool Safety Test
*This test, as well as all of the tests in this booklet, must be completed by the
Elementary/Maker teacher and should be retained by the school district administration.
Teacher name: _______________________ Date: __________________
1. When using the handsaw, fingers should be at least how far away from the teeth?
________________
2. If it is difficult to control the material you are sawing, what should you do?
________________________________________
3. Describe how you would use a hammer to nail two pieces of wood together.
________________________________________________________________
_______________________________________________________________
4. Describe how to safely use a wood chisel. _____________________________
________________________________________________________________
________________________________________________
5. What should you do if you get hot glue on your finger?
_____________________________________________________
6. How do you test to see if a plane or spoke shave is sharp? _________________
_____________________________________
HEADS UP FOR SAFETY
TOPIC INFORMATION to go over with students
Accidents Immediately report all accidents or injuries to your teacher.
Behavior Be calm! Do not run or push others. Do not throw things!
Eye Protection Wear safety glasses at all times when working on projects with tools.
Housekeeping Keep floor and work areas clear and clean. Keep all materials stored where they belong. Allow time for good clean up at the end of work period.
General Workshop Safety
HEADS UP FOR SAFETY
GENERAL WORKSHOP SAFETY TEST
NAME: ____________________ DATE:________________________
1. The number one safety rule when working with tools is?
a. wear steel toed boots
b. wear safety glasses
c. unplug a power tool
2. Accidents should be reported to the teacher.
a. True
b. False
3. Three unacceptable behaviors when working with tools on a project.
a. talking, eating, drilling
b. pushing, yelling or throwing things
c. sawing, securing your work, using loud equipment
HEADS UP FOR SAFETY
SAFETY PROCEDURES Always wear safety glasses when using power tools.
Tie long hair back
Always ask teacher permission before using the tool.
Disconnect power or unplug the Drill when changing Bits.
Make sure drill bit is placed correctly in drill chuck, centered, and that the drill bit
is secured tightly in drill chuck.
Check the rotation of the drill bit before starting to drill. Forward for drilling a
hole, reverse for pulling the drill bit back out.
Beware of hot drill bits after drilling holes.
Make sure the material being drilled is held down firmly or clamp material down.
When using large bits or drilling small pieces, clamp material down.
Make sure the drill bit has a clear path under the material being drilled, or have a
scrap block of wood for the drill bit to go into after drilling through your project.
Try to have your material being drilled in a horizontal or vertical position so you
can more easily drill the hole square with the material.
Cordless Drill Clutch
Variable speed Trigger with forward/reverse switch
Chuck
Battery
HEADS UP FOR SAFETY
CORDLESS DRILL SAFETY TEST
NAME: ____________________ DATE:________________________
1. What is the number one safety rule when using power tools?
____________________________
2. Before changing drill bits you must first?
____________________________
3. Long hair should be:
____________________________
4. How should material be held down?
_____________________________
5. You must ask teacher permission before using the cordless drill.
a. True b. False
HEADS UP FOR SAFETY
SAFETY PROCEDURES
Always wear safety glasses when using power tools.
Never talk or disturb someone while they are working with a machine.
Always ask teacher permission before using the tool.
Disconnect power or unplug the saw when changing blades or making
adjustments to the saw.
Clamp the material down or hold firmly. Hands no closer to blade than
4”.
Check and make sure the blade has a clear path under the material
before starting a cut.
Plan cuts to avoid backing out of a cut.
Use relief cuts when making sharp curves.
Jigsaw
Trigger and speed control
Tilt base for angle cuts
Battery
Cutting direction/tool path
HEADS UP FOR SAFETY
When making curved cuts, always move the saw forward so the teeth
of the blade are cutting.
Keep your fingers out of line with the blade and at least 2” away from
the blade.
The blade should be completely stopped before lifting the blade away
from the material.
At the end of machine use, clean area and place tool in a safe place so
it does not fall.
If the blade starts cutting where you do not want it to, then release
jigsaw trigger and let the blade stop.
HEADS UP FOR SAFETY
JIGSAW SAFETY TEST
NAME: ____________________ DATE:________________________
1. What is the number one safety rule when using power tools?
_____________________________________________
2. You should always clamp your material down?
a. true b. False
3. To avoid backing out of a cut, or when cutting sharp curves, you should use
relief cuts?
a. true b. False
4. Before lifting the jigsaw up from the material being cut, you must:
_________________________________________
______________________________________________
5. You must ask teacher permission before using the jigsaw.
a. True b. False
6. Why must you always check there is a clear path under the material before
a cut? ____________________________
______________________________________________
7. Your fingers should always be at least how far away from the blade?
__________ inches