X-FB-E and X-DFB-E Electrical Conduit Fasteners / 2015 1 X-FB-E G X-FB-E and X-DFB-E Electrical...
-
Upload
nguyenthuan -
Category
Documents
-
view
216 -
download
0
Transcript of X-FB-E and X-DFB-E Electrical Conduit Fasteners / 2015 1 X-FB-E G X-FB-E and X-DFB-E Electrical...
12 / 2015 1
X-FB-E
G
X-FB-E and X-DFB-E Electrical Conduit Fasteners
General information
Material specifications
Galvanized steel sheet fu = 270-420 N/mm2
10-20 µm zinc coating
Recommended fastening tools
GX 120-ME, GX 100-E
DX 351-MX, DX 351-F8
DX 460-MX, DX 460-F8See X-FB-E fastener program in the next pages for more details.
Dimensions
Product data
Example
Applications
X-FB-E for rigid conduits
X-FB-E for flexible conduits
X-FB-E X-DFB-E
Wd
H
W
d
H
X-GN 20/27
o 6.
8
o 3
1.8 Ls
L
X-GHP 20
o 6.
8
28.9
27
o 3
1.9
X-C 22/27
o 3.
5
Ls2
L
o 8
Recommended loads
Load data
X-FB-E
2 12 / 2015
G
Thickness of base material
Application requirements
X-GN, X-GHP: hmin = 60 mmX-C: hmin = 80 mm
Thickness of fastened material
X-FB-E: To fasten conduits, pipes and tubes of ∅ 16 mm to 25 mmX-DFB-E: To fasten conduits, pipes and tubes of ∅ 20 mm to 25 mm
Spacing and edge distances
Space fastenings as needed to control sag and maintain alignment.
Corrosion information
These zinc-coated fasteners are not suitable for long-term service outdoors or in otherwise corrosive environments.For further detailed information on corrosion see relevant chapter in Direct Fastening Principles and Technique section.
Concrete Sandlime stoneFastener Nrec [kN] Nrec [kN]
X-FB-E or X-DFB-E with X-GN 20 nail 0.02 0.02
X-FB-E or X-DFB-E with X-GN 27 nail 0.06 0.06
X-FB-E or X-DFB-E with X-GHP 20 nail 0.02 –
X-FB-E or X-DFB-E with X-C 22/27 nails 0.06 0.06
Application limits
X-GN, X-GHP fcc ≤ 30 N/mm2
X-C fcc ≤ 45 N/mm2
12 / 2015 3
X-FB-E
G
Tool selection
X-GN, X-GHP: GX 120-ME, GX 100-EX-C _P8: DX 351-F8, DX 460-F8X-C_MX: DX 351-MX, DX 460-MX
Fastening quality assurance
Fastener selection and system recommendation
Fastenerprogram
Designation Item no. d [mm] W [mm] H [mm]
X-FB-E 16 MX 2112585 16 44 17.5
X-FB-E 20 MX 2112586 20 48 21.5
X-FB-E 25 MX 2112587 25 55 26.5
X-DFB-E 20 MX 2112588 20 80 20
X-DFB-E 25 MX 2112589 25 90 25
X-GN 20/27 nails Nail shank: Carbon steel, HRC 53.5, Zinc coating: 2-13 µm
X-GHP 20 nail Nail shank: Carbon steel, HRC 58, Zinc coating: 2-13 µm
X-C 22/27 nails Nail shank: Carbon steel, HRC 56.5, Zinc coating: 5-20 µm
System recommendation
Nailhead not protruding
DX tools
DX 351-F8DX 460-F8DX 351-MXDX 460-MX
Concrete
6.8/11M yellow cartridge on green/fresh and standard concrete
6.8/11M red cartridge on precast, old and hard concrete
Masonry 6.8/11M green cartridge
GX tools GX 120-ME Gas can GC 20, GC21 and GC22
GX 100-E Gas can GC 11 (GC 12 in USA)