Work Supports // High Capacity // Fluid Advance NEW ...
4
© Vektek LLC, 2018 800-992-0236 4 U.S. PATENT NO. 5,957,443 PATENT PENDING ILS100729 REV 4 Work Supports // High Capacity // Fluid Advance NEW! Replace older models with higher capacity cartridges or complete with bases! Plungers stay retracted during part loading. Hydraulic pressure advances the plunger exerting only spring force as it makes contact with the part. Hydraulic pressure then automatically sequences, “freezing” the plunger, to properly support the part. Available in 1800 or 3500 lb. capacity. Order with base or cartridge only. Ventless configuration and built in wipers protect the plunger movement from chips and debris. Up to 3X capacity of competitor’s version. Uses Vektek’s BHC technology to guard against corrosion. O-ring face seal design makes machining cavities easier. Standard SAE porting and alternate o-ring manifold face seal is located in the base of the support for bolt down installation. The base can be removed for direct cartridge mounting. Specifications Model No. Direct Replacement for Older Model Support Capacity (lb.)* Mounting Style*** Contact Force (lb.) Stroke (in.) Base Dimensions (in.) Retracted Height (in.) Oil Capacity (cu. in.)** Fluid Advance Work Supports, hydraulic pressure pushes a spring which lifts plunger, hydraulic pressure locks in place. 10-0706-10 10-0706-04 1800 Cartridge 1-6 0.25 N/A 2.14 0.06 10-0806-10 10-0806-05 SAE/Manifold 0.90 X 1.31 X 1.75 2.51 0.08 10-0708-10 10-0708-07 3500 Cartridge 3-10 N/A 2.85 0.12 10-0808-10 10-0808-07 SAE/Manifold 1.25 X 1.50 X 2.31 3.25 0.15 Long Stroke Models Coming Soon--Call for availability Model No. Direct Replacement for Older Model Support Capacity (lb.)* Mounting Style*** Stroke (in.) Fluid Advance Work Supports, hydraulic pressure pushes a spring which lifts plunger, hydraulic pressure locks in place. Coming Soon 10-0706-14 1800 Cartridge 0.50 10-0806-15 SAE/Manifold 10-0708-17 3500 Cartridge 10-0808-17 SAE/Manifold Precision Hydraulic Clamping Inch catalog. NOTE: The maximum system back-pressure a fluid advance work support can overcome is 10 psi. Returning back-pressure greater than 10 psi may cause slow or failed retraction. * Support capacities are listed at 5,000 psi maximum pressure. Support capacities for other pressures are shown in the fluid advance High Capacity and Part Present Sensing load capacity chart. ** Restrict flow rate to a maximum of 130 cu. in./minute. *** For cartridge mount models, see cavity dimensions drawings in this catalog section. **** For complete dimensions, see fluid advance work support section (B) in the 1800 3500 1-6 3-10 0.25 0.25 0.25 1800 3500 0.50 0.50 0.50
Transcript of Work Supports // High Capacity // Fluid Advance NEW ...
© Vektek LLC, 2018 800-992-02364
U.S. PATENT NO. 5,957,443PATENT PENDING
ILS100729 REV 4
Work Supports // High Capacity // Fluid Advance
NEW! Replace older models with higher capacity cartridges or complete with bases!
Plungers stay retracted during part loading. Hydraulic pressure advances the plunger exerting only spring force as it makes contact with the part. Hydraulic pressure then automatically sequences, “freezing” the plunger, to properly support the part.
Available in 1800 or 3500 lb. capacity.Order with base or cartridge only.Ventless configuration and built in wipers protect the plunger movement from chips and debris.Up to 3X capacity of competitor’s version.Uses Vektek’s BHC technology to guard against corrosion. O-ring face seal design makes machining cavities easier. Standard SAE porting and alternate o-ring manifold face seal is located in the base of the support for bolt down installation. The base can be removed for direct cartridge mounting.
Specifications
Model No.Direct
Replacementfor Older Model
SupportCapacity
(lb.)*
MountingStyle***
ContactForce(lb.)
Stroke(in.)
BaseDimensions
(in.)
RetractedHeight
(in.)
OilCapacity(cu. in.)**
Fluid Advance Work Supports, hydraulic pressure pushes a spring which lifts plunger, hydraulic pressure locks in place.10-0706-10 10-0706-04 1800 Cartridge 1-6 0.25 N/A 2.14 0.0610-0806-10 10-0806-05 SAE/Manifold 0.90 X 1.31 X 1.75 2.51 0.0810-0708-10 10-0708-07 3500 Cartridge 3-10 N/A 2.85 0.1210-0808-10 10-0808-07 SAE/Manifold 1.25 X 1.50 X 2.31 3.25 0.15
Long Stroke Models Coming Soon--Call for availability
Model No.Direct
Replacementfor Older Model
SupportCapacity
(lb.)*
MountingStyle***
Stroke(in.)
Fluid Advance Work Supports, hydraulic pressure pushes a spring which lifts plunger, hydraulic pressure locks in place.
Coming
Soon
10-0706-14 1800 Cartridge0.5010-0806-15 SAE/Manifold
10-0708-17 3500 Cartridge10-0808-17 SAE/Manifold
Precision Hydraulic Clamping Inch catalog.
NOTE: The maximum system back-pressure a fluid advance work support can overcome is 10 psi. Returning back-pressure greater than 10 psi may cause slow or failed retraction.
* Support capacities are listed at 5,000 psi maximum pressure. Support capacities for other pressures are shown in the fluid advance High Capacity and Part Present Sensing load capacity chart.
** Restrict flow rate to a maximum of 130 cu. in./minute.*** For cartridge mount models, see cavity dimensions drawings in this catalog section.**** For complete dimensions, see fluid advance work support section (B) in the
1800
3500
1-6
3-10
0.250.250.25
1800
3500
0.50
0.500.50
800-992-0236 © Vektek LLC, 20185
Specifications
Model No.
SupportCapacity
(lb.)*
MountingStyle***
ContactForce(lb.)
Stroke(in.)
BaseDimensions
(in.)
RetractedHeight
(in.)
OilCapacity(cu. in.)**
Port X Depthfor Optional
In-Port Valves****
Fluid Advance Work Supports, hydraulic pressure pushes a spring which lifts plunger, hydraulic pressure locks in place.10-0706-10 1800 Cartridge 1-6 0.25 N/A 2.14 0.06 N/A10-0806-20 SAE/Manifold 1.19 X 1.31 X 1.31 2.79 0.08 SAE 4 X 0.5810-0708-10 3500 Cartridge 3-10 N/A 2.85 0.12 N/A10-0808-20 SAE/Manifold 1.50 X 1.63 X 1.63 3.50 0.15 SAE 4 X 0.58
* Support capacities are listed at 5,000 psi maximum pressure. Support capacities for other pressures are shown in the fluid advance High Capacity and Part Present Sensing load capacity chart.
** Restrict flow rate to a maximum of 130 cu. in./minute.*** For cartridge mount models, see cavity dimensions drawings in this catalog section.**** In-Port valves require the use of manifold mount ports.
NOTE: The maximum system back-pressure a fluid advance work support can overcome is 10 psi. Returning back-pressure greater than 10 psi may cause slow or failed retraction.
1800
3500 3-10
1-6 0.250.25
0.25
ILS100718 REV 4
U.S. PATENT NO. 5,957,443PATENT PENDING
Work Supports // High Capacity // Fluid Advance
Now up to 3X competitive capacity at 5,000 PSI!NEW!
Plungers stay retracted during part loading. Hydraulic pressure advances the plunger exerting only spring force as it makes contact with the part. Hydraulic pressure then automatically sequences, “freezing” the plunger, to properly support the part.
Available in 1800 or 3500 lb. capacity.Order with base or cartridge only.Ventless configuration and built in wipers protect the plunger movement from chips and debris.Four bolt base is compatible with Vektek in port flow control and in port sequence valves.Uses Vektek’s BHC technology to guard against corrosion. O-ring face seal design makes machining cavities easier.Long stroke models coming soon, call for availability. Standard SAE porting and alternate o-ring manifold face seal is located in the base of the support for bolt down installation. The base can be removed for direct cartridge mounting.
© Vektek LLC, 2018 800-992-02366
Work Supports // High Capacity // Fluid Advance
ATHREAD
BC STROKE
DE
F
H
J
K
MN
AB
P
Q
Y
AA
L
T
Dimensions
10-0806-20 1-16 2.79 0.25 1.19 1.19 0.21 0.88 0.56 0.14 1.31 1.31 1.0010-0808-20 1 1/4-16 3.50 1.44 1.50 0.36 1.13 0.75 0.19 1.63 1.63 1.25
ILS100719 REV 4
10-0806-20 0.50 1.00 0.50 0.19 0.30 0.94 0.50 5/16-18 X .20 SAE 4 0.38 0.31 0.1610-0808-20 0.63 1.25 0.63 0.22 0.38 1.19 0.62 7/16-14 X .25 0.34 0.31
FLUID ADVANCE HIGH CAPACITY BASE MOUNT WORK SUPPORT DIMENSIONS
G HEX
V HEX xW THREAD
4X R THRU S
XHYDRAULIC
PORT
MANIFOLDHYDRAULIC
PORT
Model No. A B C D E F G H J K L M
Model No. N P Q R S T V W X Y AA AB
0.25
SAE 4 0.38
Fluid Advance
1800 lb. 3500 lb.Model No.* Model No.*10-0706-10 10-0708-1010-0806-10 10-0808-1010-0806-20 10-0808-20
ILS100720 REV 5
*Chart data for both High Capacity and Part Present Sensing models.
Input Pressure (PSI)
Supp
ort F
orce
(lb)
1000
2000
3000
5000
1000
2000
3000
4000
4000
0
WORK SUPPORT LOAD CAPACITY CHART
800-992-0236 © Vektek LLC, 20187
DimensionsModel No. A B C D E F G H J M V WCartridge Mount, High Capacity Fluid Advance Work Support
10-0706-10 1-16 2.14 0.25 1.72 0.24 0.21 0.88 0.56 0.14 0.92 0.50 5/16-18 X .2010-0708-10 1 1/4-16 2.85 2.29 0.33 0.36 1.13 0.75 0.19 1.17 0.62 7/16-14 X .250.25
M
B
C STROKE
ED
F HJ
ATHREAD
ILS100724 REV 4
U.S. PATENT NO. 5,957,443
G HEX
V HEX xW THREADUSE GASKET ONLY IF REPLACING
10-0706-04 OR 10-0708-07USE O-RING ONLY IN ALL
OTHER NEW APPLICATIONS
PATENT PENDING
For proper sealing, mating surface must
be flat within 0.003 in with a maximum
63 µ in. Ra surface finish.
Work Supports // Cartridge Mount
(.530 MIN) .002 A
90° X 1.020MINOR .936 .004 .530 MIN-16 UN-2B .340 MIN1
.188 MAXON OR INSIDE .125 RADIUSOIL FEED HOLE
R.125
ILS100716 REV 5
FLUID ADVANCE 1800 lb. CARTRIDGE MOUNT WORK SUPPORT CAVITY
63
R.020 MAX
WORK SUPPORT CAVITY DIMENSIONS:1800 lb. SINGLE ACTINGFLUID ADVANCE 10-0706-10(TORQUE TO 35 ft-lb)
.002-A-
(.846 MIN) .002 A
90° X 1.280MINOR 1.190 .003 .846 MIN
-16 UN-2B .563 MIN1-1/4
.188 MAXON OR INSIDE .187 RADIUSOIL FEED HOLE
R.187ILS100717 REV 4
WORK SUPPORT CAVITY DIMENSIONS:3500 lb. SINGLE ACTINGFLUID ADVANCE 10-0708-10(TORQUE TO 50 ft-lb)
R.020 MAX
63
.002-A-
FLUID ADVANCE 3500 lb. CARTRIDGE MOUNT WORK SUPPORT CAVITY
Fluid Advance High Capacity Cartridge Cavity Check List √Confirm capacity of item selected.Note the sealing surface finish requirements.Minimum depth specification represents the nominal depth of the standard Vektek base dimension. Confirm cavity drawing is appropriate for the model number used.Note specified thread depth when cutting threads.When using a bottoming tap tool, modifications may be required.When hand tapping threads, perpendicularity is essential.
