WoodN Australia Physical Properties
-
Upload
woodn-australia -
Category
Documents
-
view
221 -
download
2
description
Transcript of WoodN Australia Physical Properties
WoodN Australia
ph: NSW +61 2 9673 8010 | VIC +61 3 8540 0503
email: [email protected] | [email protected]
web: www.woodn.com
WoodN Australia Physical Properties - V2.4 - 24072012.docx
Page 1 of 4
Green Building Council of Australia Green Building Council of Italy
Unless otherwise shown or indicated the below test results are valid for all classifications of WoodN profile range.
[ General Properties ] …
Flexural Stress
(test conditions: 23°C)
EN ISO 178.03
31.7 MPa - versatilis
20 MPa – aeternus
Modulus of Elasticity (MoE)
(test conditions: 23°C)
1.996 GPa - versatilis
1.6 GPa – aeternus
Penetration Property (Brinell) EN 1534:2000 HB = 2.40 Kg/mm2
Indentation UNI 4712:61 0.388 mm
Moisture Content EN 322:93 3.13%
Screw Extraction EN 322:93 142 N/mm
Dynamic - Mechanic Analysis ASTM D4065/95 78.7°C
Density GB/T1033-1986 950 - 1100 g/dm3
Dimensional change associated to Temperature.
(15 cycles) UNI 9429:89
ornans / ornans compositus
24h +50°C longitudinal
transversal
0%
-0.1%
24h + -20°C longitudinal
transversal
-0.13%
-0.25%
versatilis / aeternus
24h +50°C longitudinal
transversal
0.07%
-0.15%
24h + -20°C longitudinal
transversal
-0.03%
-0.30%
Dimensional Change assoc. to relative humidity.
(test at 20°C) EN 318:2002
aeternus from 65% to 85% longitudinal 0.3 mm/m
from 65% to 30% longitudinal -0.2 mm/m
WoodN Australia
ph: NSW +61 2 9673 8010 | VIC +61 3 8540 0503
email: [email protected] | [email protected]
web: www.woodn.com
WoodN Australia Physical Properties - V2.4 - 24072012.docx
Page 2 of 4
versatilis / ornans / ornans compositus from 65% to 85% longitudinal 0.3 mm/m
from 65% to 30% longitudinal -0.2 mm/m
Cold-check test
(after 15 cycles, range -20 to +50°C) UNI 9429:89
Level 5:
no surface defects
Linear thermal expansion coefficient
(range -10% to +70°C)
TMA ASTM
E 831/2006
longitudinal: 46.9µm/(m°C)
transversal: 48.9 µm/(m°C)
Swelling and Water absorption - versatilis
(7 days in cold water at 20°C) /
longitudinal: 0.07%
transversal: 0.23%
thickness: 1.22%
weight 2.89%
Impact resistance at a constant temp. - aeternus
(49x33 board) GB/T 14153 6.8 [KJ/m2]
Bending Strength - aeternus
(49x33 board) GB/T 9341-2000 34 [Mpa] ≥15
Resistance to flexion at room temp.- aeternus
(span = 500mm) EN 310:1983
Break 3266 N
Distortion
2mm 500 N
Determination of resistance to chlorinated water
- aeternus
(288h at 23°C)
UNI EN ISO 10545-
13:2000
UA Class
(neither dimensional nor
structural deterioration)
Hardness - ornans / ornans compositus
(shore D) EN ISO 868/97 73
Abrasion test on pre-finished varnished planks
(4000 revolutions, results comparable to AC4
classifications)
EN 13329/00
ornans / ornans compositus Weight variation (mg) -3399
Thickness variation (mm) -0.88
Abrasion test on pre-finished varnished planks
(6500 revolutions, results comparable to AC4
classifications)
EN 13329/00
ornans / ornans compositus Weight variation (mg) -5601
Thickness variation (mm) -1.40
Determination of friction coefficient
(for B.C.R.A. method flooring with varnish)
(0.40 - 0.74 --- satisfactory friction)
ornans / ornans compositus
Direction A → B ↓
Wet Surface 0.62 0.67
Dry Surface 0.67 0.68
WoodN Australia
ph: NSW +61 2 9673 8010 | VIC +61 3 8540 0503
email: [email protected] | [email protected]
web: www.woodn.com
WoodN Australia Physical Properties - V2.4 - 24072012.docx
Page 3 of 4
aeternus
Direction A → B ↓
Wet Surface 0.62 0.66
Dry Surface 0.58 0.63
Tolerance
(general tolerance on the extrusion of the profiles) ± 0.2 mm
[ Environmental ] …
Formaldehyde release Gas analysis
(qualified class E1 EN 14041) EN 717-2/94 0.1 mg HCHO / m2 h
(max. allowed 3.5 mg HCHO / (m2 h)
Plastic-Evaluation of the action of micro-
organism. Method A. - aeternus / versatilis
(scale 0 - 5, best obtainable: “0”)
EN ISO 846/97
Incubation temp. ±29°C for 4 weeks
Obtained test level: 1
Assessment of surface resistance to cold
liquids
(classification using test UNI 10944:2001)
EN 12720:1997 Class E
[ Slip Resistance ] …
Slip Resistance Classification for New Surface
Materials
(aeternus brushed surface – SB)
AS/NZS 4586:2004 Across Grain
Wet Pendulum Test W Low
Wet Barefoot Ramp Test 37° C
Oil Wet Ramp Test 31° R12
[ Fire Properties ] …
Fire classification of construction products
and building elements.
(classification using data from reaction to fire test)
EN 13501-1
(test method:
EN ISO 11925-2
EN ISO 9239-1:2002)
Class Bfl - S1
(self-extinguishing)
EN ISO 9239-1:2002
AS ISO 9239.1:2003
Mean
Critical Radiant Flux 10.62 kW/m2
Smoke Value 163.19 %min
WoodN Australia
ph: NSW +61 2 9673 8010 | VIC +61 3 8540 0503
email: [email protected] | [email protected]
web: www.woodn.com
WoodN Australia Physical Properties - V2.4 - 24072012.docx
Page 4 of 4
(radiant panel - isotropic material) UNI 9174/87 and
9174/A1/96
Class Bfl - S1
(self-extinguishing)
(small flame - isotropic material) UNI 8457/87 and
8457/A1/96
Class 1
(self-extinguishing)
Bushfire Attack Level ( BAL ) AS 3959:2009 BAL – 29
Fire Hazard Property - BCA AS/NZS 3837:1998 Group 3
Fire Indices AS/NZS 1530.3:1999
Ignitability Index
Spread of Flame
Heat Evolved
Smoke Developed
8 [0-20]
0 [0-10]
0 [0-10]
7 [0-10]
[ UV Resistance ] …
DT13835
aeternus SB – (light – W9)
SAE J1960-2004
ISO-105-A02-1993
500h – Colour Change 3
1000h – Colour Change 2-3
DT13835
aeternus SB – (dark – W13)
SAE J1960-2004
ISO-105-A02-1993
500h – Colour Change 3-4
1000h – Colour Change 3
This publication is intended as an aid for architects, engineers, specifiers and professionals involved in the design and specification of
WoodN products.
This publication is subject to modifications without notice.