Approximate Weight: 3500 lbs

WHITMORE FIRE PIT

www.midwestmanufacturing.com

Approximate Size: 4’ 4-1/2” x 4’ 4-1/2” x 2’ 1/2”

SIENNA198-6064

TAN198-6065

AUTUMN BLEND198-6066

QUARRY GRAY198-6063

32 PREPARE

PRODUCT

Belgian Wall Large Block Belgian Wall Medium BlockBelgian Wall Small Block8” Standard Construction Block

QUANTITY

525224 16

CONCRETE BLOCK MATERIALSDESCRIPTION

Color of ChoiceColor of Choice Color of Choice

Gray

Belgian WallLarge Block

Belgian WallMedium Block

Belgian WallSmall Block

BELGIAN WALL BLOCKS

179-3650179-3648

179-3653

179-3640

Large

179-3721179-3722

179-3723

179-3724

Medium

179-3731179-3732179-3733

179-3734

SiennaQuarry Gray

Tan

Autumn Blend

SmallColor

STANDARD CONSTRUCTION BLOCK

179-3069

8x8x16

GrayColor

ADDITIONAL MATERIALS

PRODUCT

36” Square Fire Pit Insert Fire Pit Adhesive

DESCRIPTION

Steel10 oz Tube

QUANTITY

18

SKU#

259-5153638-4313

Standard Construction Block8x8x16

A solid foundation is necessary to prevent settling and tiling of each project. We recommend using a leveling pad, unless local building code requires you to pour a concrete foundation or build another type of foundation. ***Fire ring should be placed on stone, dirt or sand surfaces. Pavers or concrete can be installed around fire ring, but should not be under fire ring. Fire Ring should not be placed on wood or composite decking surfaces.

FOUNDATION:

• Choose the location for the completed project; place and mark the position of the base layer of blocks. Once marked, remove the blocks and the organic top soil within the marked area.

• If applicable to your area, create a leveling pad with a non-frost susceptible, well graded, compacted angular gravel-sand mixture with fines (GW as per ASTM D248). The leveling pad should be a minimum of 4 to 6 inches thick. For leveling pads greater than 8” thick, the fill material shall be placed in more than one lift. Each layer or lift of fill material shall be leveled and compacted to a 95% Standard Proctor density before moving on.

• Once the top layer of fill material is compacted and level, place the base layer of blocks. The base layer should sit 1 to 2 inches below grade to help further prevent shifting. Use additional fill material to level the base layer as needed.

* If a concrete slab is required, prepare a leveling pad using the procedures listed in the paragraphs above. The concrete shall have a minimum compressive strength of 2500 psi. A 4-inch thick concrete slab should be more than sufficient. A thickened edge and reinforcement of the leveling slabs may be required. Please consult a professional engineer for specific requirements.

TIPS FOR BUILDING LEVELING PADS:

3PREPARE

Rubber Mallet

Level

Utility Knife

Caulk Gun

Protective Equipment

Tape Measure

TOOL CHECK LIST These plans will walk you through each step as you Prepare, Assemble and Enjoy the new addition to your yard. Check out the Progress Bar at the bottom of each page to track your advancements as you complete each phase of your project!

INSTRUCTIONS:

• Please research and follow local building codes prior to the excavation, construc-tion and assembly of your project.

• Exercise caution when you work with Concrete Block designs. Wear pro-tective safety equipment such as safety glasses, dust masks, gloves and a hard hat.

• Whether you plan to build the project yourself or to hire a professional, every project requires a call to mark your utility lines.

BEFORE YOU BEGIN:

PREPARE ASSEMBLE ENJOY

It is the responsibility of the owner to ensure compliance with all applicable laws, codes and regulations for any project. Proper safety precautions must be taken prior to and during the construction of each project. Please follow standard safety guidelines and wear necessary protective equipment when building and using your new backyard addition.

RESPONSIBILITIES:

PREPARE:

FIRE PIT DIMENSIONSTABLE OF CONTENTS

Level 1 - Level 4

Materials ListTool Check ListFoundation Guidelines

ASSEMBLE:

Level 5 - Level 8Level 9 - Complete

Finished ElevationsENJOY:

Use and Care InstructionsMore Concrete Block Ideas

233

567

89

10

2’ 1/2”

4’ 4-1/2” 4’ 4 - 1/2”

4 PREPARE

TECHNIQUES

Fasten each layer of block together with 1/4” - 3/8” bead of adhesive on all adjacent block faces unless otherwisenoted. Refer to the adhesive’s application instructions for proper use.

Follow suggestions on page 3 to build a proper foundation before starting your new project. If not already set, place the first level of block 1”- 2” below grade, level and fill in any gaps. Use Level 1 as a reference to place the blocks for all remaining levels.

Refer to the illustrations on the following pages to guide you through each step. Prior to adhering each level to the previously laid block, place the entire level of blocks and check to make sure the fire pit insert fits properly. Remove small sections at a time to place the adhesive.

Once all levels are complete, position the insert into the finished pit. Wait a minimum of two days before starting a fire.

INSTALLATION INSTRUCTIONS

* Do not over apply adhesive. It may reduce effectiveness. Use mineral spirits to remove any unwanted adhesive.

(8) Belgian Wall Block Level 1 Level 2

(20) Belgian Wall Block

ASSEMBLE 5

4’ 4-1/2” 4’ 4-1/2”

(8) 8” Standard Construction BlocksLevel 4Level 3

(8) 8” Standard Construction Blocks

(8) Belgian Wall Medium Block

3’ 2-1/2”3’ 2-1/2”

(20) Belgian Wall Medium Block

Level 7 Level 8

Level 5 Level 6

6 ASSEMBLE

(8) Belgian Wall Medium Block

(24) Belgian Wall Small Block

4’ 4-1/2” 4’ 4-1/2”

(8) Belgian Wall Block

(8) Belgian Wall Medium Block (8) Belgian Wall Block

4’ 4-1/2”4’ 4-1/2”

3’ 9-1/2”3’ 9-1/2”4’ 4-1/2”4’ 4-1/2”

-use bracing to support overhanging blocks for a minimum of 24 hours to allow adhesive to dry

Level 9 Level 10

ASSEMBLE 7

(1) Backyard Creation’s 36” Square Fire Ring (8) Belgian Wall Medium Block (8) Belgian Wall Block

4’ 4-1/2”4’ 4-1/2”

-use bracing to support overhanging blocks for a minimum of 24 hours to allow adhesive to dry

3’ 0”3’ 0”

Completed Table

8 ENJOY

ELEVATIONS

Left View Right View

Front View

Top VIew

Back View

With proper use and maintenance you can enjoy this new addition to your landscape for years to come. Fire Pit Use:• When using your fire pit, always following burning regulations in your area and never

leave a fire unattended.

• Keep the fire within the metal insert; any exposure of the flames directly to the concrete blocks may cause blackening or cracking of the blocks.

ENJOY

Use and Maintenance

9

Fire Pit Maintenance: • Clean your fire pit often.

• Wait until the fire has burned out completely and all ashes have cooled before cleaning the fire pit.

• Begin by removing the larger pieces of debris; the remaining ash can be scooped out and/or lightly sprayed with a hose to rinse away.