Welding Products(Pg164-180) (1)

7/23/2019 Welding Products(Pg164-180) (1)

http://slidepdf.com/reader/full/welding-productspg164-180-1 1/1764

Allinton Engineering & Trading Pte Ltd Head Ofce: 331 Jalan Besar, Singapore 208983. 6296 0679 (10 lines) 6297 0024

Branch Ofce: 21 Tuas Basin Link Singapore 638782 6265 1888 (10 lines) 6265 5623www.allinton.com.sg [email protected] [email protected]

Wind Yama Portable Ventilator

AS00003

AP-200Portable VentilatorSize: 8”

Rotation: 3460rpmHP: 150WVoltage: Single Phase 110V, 220V Three Phase 220V, 380V

AP-300Portable VentilatorSize: 12”

Rotation: 3460rpmHP: 550WVoltage:Single Phase 110V, 220VThree Phase 220V, 380V

AS00004Features1. Aluminium blades compact in size, easy to operate.2. Single-phase condensor motor eliminates the problems of over-heating of three-phase motors.3. Aluminium blades have been subject to balance correction with computer.

For Use In1. Underground tunnels shipyards honeycomed locales & narrow places.2. To suck away toxic gases when welding and keep air fresh.3. Perfect for storage compartments, warehouse and electric cable

construction sites.

Code No. Model No. Weight Voltage P Hz m³/min m/Aq r.p.m pH kg

AS00003 AP-200 150 110 & 220 2 50 25 35 2.930 1pH 10.360 30 42 3460

AS00004 AP-300 550 110 & 220 250 60 40 2.930

1pH 19.760 70 50 3460

Ventilation Hose (5 MTR/10 MTR)

AS00016

Flexible DuctDia:From 180m/m - 1000m/mLength Measure:From 1m - 20m

Connection Flexible DuctEasily fitted extensions can extend the duct. Simplyslip the extension over the ring on the end of theduct and securely tie the cord

5 MTR

Code No. Size

AS00016AS00017AS00018AS00019AS00020

AS00021AS00565

200mm/8”300mm/12”350mm/14”400mm/16”500mm/20”

600mm/24”800mm/32”

10 MTR

Code No. Size

AS00366

AS00367AS00368AS00369

AS00370AS00566AS00574AS00575

200mm/8”AS00124 250mm/10”

300mm/12”400mm/16”500mm/20”

600mm/24”800mm/32”900mm/36”1000mm/40”

WIND YAMAWIND YAMA WEV 400 16” and WEV 600 21” variable speed turbo blowers offermore power, higher performance, no CO and are GFCI–compatible, too!

You Control The 1.5HP Force•

From full PPV for fast clearance of dangerous smoke and gases to slower speedsfor cooling overheated firefighters is as easy as turning the control knob on the

control panel. IntelliSense™ Controls The Start Up Power •

This exclusive water–resistant electronic control feature monitors and limits theamount of start up power to allow operation on GFCI Circuits and for starts ongenerators as small as 2kW.

Specifications

Code No. Model No. HP Dimensions Motor MFG/Model No. Wt RPM Set Back Angle Airflow

AS00355AS00356

WEV400-16”WEV600-21”

1.51.5

23H x 17W x 16D24H x 18W x 24D

YM-EM-F1.5-90YM-EM-F1.5-90

7480

35883588

6’8’

20°13°

9,705 CFM11,061 CFM Tilt Adjustment helps you

quick direct the FORCE

23”

Compartment friendly size and shape

17”

16”Deep

Welding Products





Onishi Portable FanMAMA-TA

Remove Hot Air and Harmful Gases and Supplies Fresh Air and Oxygen. The machinehas made many safe and comfortable working environments.

Feature1. The breaker of motor is fitted to prevent the motor from burning out.2. Portable type, convenient to carry.3. The ideal-bell mouth type casing has high efficiency and low noise.4. Our unique water-proofed switch is very durable.

* Uses

removing harmful gases andsupplying fresh air

ventilation and reduction ofhigh temperatures

manhole ventilation

*WIN MAMA–TD outline dimension.

Item Name

12345678910

MotorFitting Plate

HandleImpeller

Wire NetCasingSwitchGlandRubberCable

*Particulars

Code No.Casing

DiaVolt(V)

Output(kW)

RPM(rpm)

Freq.(Hz)

QuantityPress

mmAqRating

Weightkg

AS00005 280 100/200 0.55 3000/3600 50/60 70cu.m/min 30 Cont 18

* Distribution of Wind Velocity at 60Hz

WIN MAMA-TC

Flexible duct are over tape type and sewing type.

WA2-2, WA2-5

Light Weight, Solid, Powerful Fan. The quality has been proved by the 30-yearhistory.

Feature1. The weight is lighter than ordinary fan.2. The one-piece motor makes maintenance much easier.3. Great care has been taken to prevent noise and danger and we recommend

the equipment as a reliable product.4. The equipment has the capacity of wind which ordinary portable fan cannot

get.

* UsesWelding work, Manhole ventilation (removing harmful gases and supplyingfresh air and oxygen) Ventilation of tanks and reduction of high temperature.Flexible ducts (over tape type and sewing type) are connected easily.

W i n A c e C h a r a c t e r i s t i c C u r v e

Item Name

12345678

CasingImpellerMotor

Fitting PlateTerminal Box

HandleWire NetRubber

*Particulars

Code No. Type Output RPM Freq Capacity Press Weight A D H h W Q L P l gland

AS00006AS00007

WA2–2WA2–5

1.5kW3.7

3000/60003000/3600

50/60Hz50/60

80cu.m/min150

50mmAq70

35kg64

400dia.500

436dia.536

556656

272322

370470

300400

436506

300350

6878

20C25A

AS00005

AS00006

JAPAN

Welding Products





Onishi Explosion Proof Fan

AS00008dimension for

BM-B

Features1. The Lightest Weight: BM-B---------25 KG

BB-B ---------14.5 KG2. Safety: Exp. Proof Grade d2G4. Non-Sparking Type

3. Useful: Fitting with a Exp. Proof Switch Cabtire.Cable 5M Length

Particulars

Code No. Type Dia:mm Output Source Quantity Pressure Weight

AS00008 BM-B 300 0.55kW1 Ø 50 / 60Hz

0.18kW

AC100V 70m³/min 30mmAq 25kg

AS00009 BB-B 200 AC230V 20m³/min 20mmAq 14kg

Blowers

AS00354

Portable Pneumatic Ventilator

Model: KMA300F 12” orKMA400F 16”Dia: 12” or 16”Intrinsic Safe for HazardousEnvironmentsISSA: 59 14 25 & 26

AS00353

Portable Fan

AS00623 AP-7 600mm/24” 3.0HP/230V/50Hz 1400 RPM Single 290m3/min

Code No. Model Size Power Max RPM Speed Max Rated

AS00631 AP-7 600mm/24” 3.0HP/415V/50Hz 1400 RPM 3Phase 290m3/min

AS00623

Jumbo Axial Fan Portable Fan


AS00624

Explosion Proof Electric Blower

Model:Dia:

AES200mm 8” AES300MM 12”200mm (8”), 300mm (12”)

Voltage:Phase:

115 / 230Single

Anti–static ABS Housing, Chemical Resistant UL Class I, Group D &Class II, Group E, F, G. RAMFAN, USA

Pneumatic Blower

Model: AAF 300MM 12” Dia: 12”Anti–static ABS Housing, Chemical Resistant, USA

AS00323 AES 8”AS00324 AES 12”

AS00325 AAF 12”

AS00628



AS00630 AF-6 500mm/20” 2.2HP/415V/50Hz 2800 RPM 3Phase 138m3/min


AS00624 AP-2 200mm/8” 1/4HP/230V/50Hz/60Hz 2800 RPM Single 25m3/min

AS00625 AP-3 300mm/12” 1/4HP/230V/50Hz/60Hz 2800 RPM Single 63m3/min

AS00627 AP-4 350mm/14” 1.0HP/230V/50Hz/60Hz 2800 RPM Single 82m3/min

KMA300F 12” KMA400F 16”

Welding Products





Water Driven Turbine Fan

Model:

Dia:

ATF 12” or ATF 16”300mm/12”, 400mm/16”

Dia:

Phase:

12” & 16”Single

Water Connection: 2½” NST

Pneumatic Blower – Blower / Exhauster

Tornado Electric Blower (Explosion Proof)

Model: 8AXP, 12AXPThe Explosion Unit is approved and certified by American Bureauof shipping (ABS) Ideal for exhaust applications Prime–Air, USA

Venturi Air Blower (Air Mover)

Model: ARV760, ARV760S, ARV1500High output, Lightweight, Portable anti–static, Crush Proof Conductive Polymer Diffuser.Weather Proof and Chemical Resistant. Powered by compressed air or saturated steamRAMFAN. USA.

Hurricane Venturi Blower

Model: AHV3P, AHV3, AHV6, AHV8, AHV10The Explosion Unit is approved and certified by American Bureauof shipping (ABS) Ideal for exhaust applications Prime–Air, USA

Air Driven Gas Freeing Fan

Model:

Air Inlet:

AGFF 12” or AGFF 16”3/4” or 1” NPT

Dia: 12” & 16”

AS00328 ATF 12”

AS00329 ATF 16”

AS00332 8AXP

AS00333 12AXP

AS00334 AHV 3P

AS00335 AHV 3

AS00336 AHV 6AS00337 AHV 8

AS00338 AHV 10

AS00339 ARV-760

AS00340 ARV-760S

AS00341 ARV-1500

AS00330 AGFF-12AS00331 AGFF-16

AS00327 AET-20

AET - Industrial Fan

24” Industral Wall FanAS00025

26” Industral Stand FanAS00024

20” Industral Desk FanAS00022

Code No. Model Description

AS00326 AET - 12AET - 16AET - 20AET - 24

12” Jet Fan16” Jet Fan20” Jet Fan24” Jet Fan

AS00701AS00327AS00702

Code No. Size

AS00027 20”24”26”

AS00025AS00026

Code No. Size

AS00022 20”

Code No. Size

AS00028 20”24”26”

AS00023AS00024

Description:This four-bladed vaneaxial fan is called a Jet Fan because ahighvelocity jet of compressed air is ejected from the trailingedge of the blade, as shown in the diagram. This results inthe forward rotation of the fan wheel just like a jet plane ispushed forward by the high-velocity jet ejected from the rearof the jetengine.

• Use for general ventilation in any location wherecompressed air is available. Use as blower or exhauster.

• Suited for ventilation of tanks, process vessels, or otherconfined areas for the removal of hazardous fumes orcontaminated air from welding, sandblasting and otheroperations.

• Rated operating pressure 40-110 PSI.• Design allows for lower RPMs while still moving more air.

• Bearings are packed with a hi-tech synthetic lubricant forlonger life.

• Propeller precision balanced by removing material fromend of blades.

• Use as blower or exhauster.

• Electro polished stainless steel fan guard.• Heat treated to T6 aircraft aluminum specifications.• Super-duty, high quality, high pressure air seal for longer

service.• Heaviest-duty fan in the industry.• Hi-tech four blade design.• Guide vanes to eliminating turbulence which smooths air

flow and increases effeciency.• Fan design by one of the foremost fan engineers in the

world.

Welding Products





Welding CableBlack

AS00105AS00106AS00107AS00108

300AMP400AMP500AMP600AMP

Welding CableOrange

AS00109AS00110AS00111AS00112

300AMP400AMP500AMP600AMP

Black NeopreneCable

AS00113AS00114AS00115

–

300AMP400AMP500AMP

–

Orange NeopreneCable

AS00116AS00117AS00118

–

300AMP400AMP500AMP

–

5. Specification

Nominal areaof conductor

mm

Conductive coreNo. of wire x Dia.

mm

Max. overallDia. of cable

mm

Approx. weightof cablekg/km

Max. D.C. resistance of conductorat 20°C not more than rad./km

tinned untinned

101625

35507095120150185

322/0.20513/0.20798/0.20

1121/0.201596/0.202214/0.202997/0.201702/0.202135/0.301443/0.40

9.711.513.0

14.517.019.522.024.027.029.0

140212308

423592828

1088137416662044

1.911.16

0.758

0.5360.3790.2680.1980.161

0.15290.1069

1.951.19

0.780

0.5520.3900.2760.2040.1640.1320.108

Welding Cable

Main Productsbare wiresmagnetic wiresrubber insulated electric wiresplastics insulated electric wirestough rubber sheathed arc welding electrode cabletough rubber sheathed flexible cables for general purposesPVC-insulated & PVC - sheathed power cablePVC-insulated & PVC - sheathed control cablePVC-insulated & PVC - sheathed signal cable

AS00115

AS001183 2 1

Flexible Copper - core cable for welding machines1. Application–The product is applied up to A.C 200 V and pulsating D.C. 400V at the

secondary of welding machine against the earth and connecting welding guns. TheMax. continuous operating temperature of conductor is 65ºC.

2. Type YH3. Standard of Product–The product verified by CCEE accors with the demands of GB

5013.3 85 (equal to IEC 245)4. Construction

1. conductor of the cable

3. rubber insulated sheath

2. isolated layer lapped thermo-resistantfilm or other fiber tapes

Code No. Model Code No. Model Code No. Model Code No. Model

Code No. AS00091 AS00092 AS00093 AS00094 AS00095

Size(mm) 4.5 x 305 5.0 x 305 6.5 x 305 8.0 x 305 9.0 x 305

Code No. AS00641 AS00642

Size(mm) 1.5 2.5

Code No. AS00660 AS00661 AS00662

Size(mm) 2.5 x 350 3.2 x 350 4.0 x 400

Code No. AS00663 AS00664 AS00665

Size(mm) 2.5 x 350 3.2 x 350 4.0 x 400

Code No. AS00666 AS00667 AS00668

Size(mm) 2.5 x 350 3.2 x 350 4.0 x 400

Code No. AS00673 AS00674 AS00675

Size(mm) 2.5 x 300 3.2 x 350 4.0 x 350

Code No. AS00679 AS00680 AS00681

Size(mm) 2.5 x 300 3.2 x 350 4.0 x 350

Code No. AS00676 AS00677 AS00678

Size(mm) 2.5 x 300 3.2 x 350 4.0 x 350

Code No. AS00669 AS00670 AS00671 AS00672

Size(mm) 2.5 x 350 3.2 x 400 4.0 x 400 5.0 x 400

Gouging Rod Brazing Alloy Rod

CHE40Welding Rod for Mild SteelAWS A5.1 E6013

Welding Rod

CHE43Welding Rod for Mild SteelAWS A5.1 E6019

CHE56Low Hydrogen Welding Rod for High Tensile SteelAWS A5.1 E7016

CHS002

Welding Rod for Extra-low Carbon Stainless SteelAWS A5.4 E308L-16

CHS062

Welding Rod for Stainless SteelAWS A5.4 E309L-16

CHE58-1High Toughness Welding Rod for High Tensile SteelAWS A5.1 E7018-1/E7018

CHS022Welding Rod for Extra-low Carbon Stainless SteelAWS A5.4 E316L-16

Welding Products





WELDMASTER PROTABLE MMA SERIES

The WELDMASTER PROTABLE MMA 160/200 is a single–phase DC inverter arc welding power source with Constant Current (CC) output characteristics providing the bestcombination of power, portability and convenience. Designed for STICK and High Frequency TIG welding applications.

A good welding performance is available when welding stainless, mild steels and easy start.

WELDMASTER HEAVY DUTY MMA SERIES

The WELDMASTER HEAVY DUTY MMA 300S/400S is a DC ARC Welding power supply with high performance characteristics. All the machines come standard with an arcforce and hot star t adjustment and, this power supply excellent for all types of stick electrodes, particularly the 6010 electrode. All machine ar provided with lift TIG for highquality TIG starting with no High Frequency.

A good welding performance is available when welding stainless, mild steels and easy start.

Code No. AS00528 AS00529Model No. MMA200 MMA160

Machine Specifications

Input Voltage 220V/240V 1ph 50/60Hz 220V/240V 1ph 50/60Hz

Input Current 21A (32A) 32A (42A) 15A (22A) 23A (33.5A)

Insulation Class HH

Open Circuit Voltage 62V/66V 56V/61V

Duty Cycle (40°C) 100%@200A60%@200A100%@160A

100%@160A60%@160A

100%@125A

Welding Current 10–200A 10–160A

Load Voltage 18V 28V 16.4V 26.4V

Protection Class 12PI12PI

Dimensions (L x W x H) 420 x 160 x 265mm 420 x 160 x 265mm

Weight gk21gk5.21


Model No. MMA 300S MMA 400S



Input Current 12.5A (16.5A) 17.2A (22.5A) 20.5A (25.3A) 26A (31.6A)

Insulation Class HH

Open Circuit Voltage 78V/85V 78V/85V

Duty Cycle (40°C) 100%@300A60%@300A

100%@250A100%@400A

60%@400A100%@350A

Welding Current 10–300A 10–400A

Load Voltage 22V 32V 26V 36V



Weight gk15gk94

AS00528/29

AS00530/31/32

WELDMASTER PORTABLE TIG SERIES

The WELDMASTER PORTABLE TIG 200P/200A is a single–phase DC inverter arc welding power source with Constant Current (CC) output characteristics providing the bestcombination of power, portability and convenience. Designed for STICK and High Frequency TIG welding applications.

All machine are provided with a built in gas valve, down slope, pulser and high frequency starting. A fixed preflow is provided and the current level automatically adjustspostflow. A good welding performance is available when welding stainless, mild steels and easy start.


Model No. TIG 200P TIG 200A


Input Voltage 220/240V 1ph 50/60Hz 220/240V 1ph 50/60Hz

Input Current 21A (32A) 23A(33.5A) 18.5A(26A)

Insulation Class HH

Open Circuit Voltage 56/61V 42/46V

Duty Cycle (40°C)60%@200A100%@160A

60%@160A100%@140A

40%@200A

60%@160A

100%@125A

Welding Current 10–200A 10–160A 10–200A

Load Voltage 18V 26.4V 18V


Dimensions (L x W x H) 420 x 160 x 265mm 370 x 150 x 245mmWeight gk9gk21

AS00538/39

Welding Products





WELDMASTER PLASMA CUTTER PCM SERIES

The WELDMASTER PLASMA CUTTER PCM range is an air plasma cutting power supply with Constant Current (CC) output characteristics offering the highest value. Highfrequency, gas switch and post–flow function are all build in.

A good cutting per formance is available when cutting stainless, mild steels, aluminium and easy start. A tought lightweight design makes it ideals for light industrial application.

WELDMASTE HEAVY DUTY GMAW SERIES

The WELDMASTER HEAVY DUTY GMAW POWER 500CV/500MST provides excellent arc performance with solid wire in short circuit, globular and spray transfers, and withflux or metal core wires in globular and spray transfer modes.

Standard features include; a 14–pin amphenol connector and dual auxiliary power outlets (115VAC, 5A fuse protected), solid state contactor, output votag regulation, build–inoverload protection, volt and amp meters, citater, environmental protection for optimum reliabiltity in harsh environments.

Code No. 44500SA34500SA04500SA

Model No. 001MCP08MCP04MCP


Input Voltage 220V/240V 1ph 50/60Hz 380V/415V 3ph 50/60Hz 380V/415V 3ph 50/60Hz

Input Current )A85(A15)A12(A71)A5.62(A6.81

Insulation Class HHH

Open Circuit Voltage V514 /V083V603 /V082V172 /V842

Duty Cycle (40°C)40%@40A100%@30A

A051@%001A08%001

Cutting Current A051–02A08–02A04–51

Load Voltage V041V211V69

Gas Type/ Flow Air @ 95lpm (200scfh) Air @ 190lpm (400scfh) Air @ 190lpm (400scfh)

Gas Pressure )isp07(rab8.4)isp07(rab8.4)isp07(rab8.4

Protection Class 32PI32PI12PI

Dimensions (L x W x H) 420 x 160 x 265mm 550 x 300 x 490mm 560 x 360 x 880mm

Weight gk501gk85gk21

Code No. 73500SA63500SA

Model No. POWER 500CV POWER 500MST



Input Current 35.5A (38.5A) 35.5A (38.5A) 36A (41A) 29A (33A)

Insulation Class HH

Open Circuit Voltage V58 /V87V58 /V87

Duty Cycle (40°C)60%@500A

100%@450A60%@500A

100%@450A

Welding Current A005–03A005–03

Load Voltage 39V 39V 40V 30V



Weight gk07gk07

AS00540 AS00543 AS00544

AS00536/37

Welding Products





TG2-11G Hand Pipe Gas CutterThe TG2–11G is a manually operated portable pipe cutting machine with a chain and geardrive system.The machine will exhibit excellent performance in straight and bevel cutting of all sizes ofpipes, which accounts for most of pipe cutting work, being habitually used by many users.Especially compliant for field work without power supply.

Cuts any size pipe bigger than100mm (4’)•

Ability to cut large pipe diameters (The chain for the maximum dia is 600mm)•

Low gear ration and Control valves•

Graduated bevel collar•

Light–weight and Excellent operability•

Cutt ing Thickness Up to 50mm (2”)

Pipe Cutting Diameter100~600mm (4~24”)by standard chain (2.4m = 96”) over600mm by extra chain addition

Cutting Shape I, V (up to 45°)

Drive Method Manual

Weight 10kg (22lbs)

TK-30 Semi–Automatic Gas Cutting MachineThe TK-30 is a semi–automatic (manually guided/portable) cutting machine which can beoperated freely by hand.

The excellent operability allows the machine to be used for many purposes.Light weight for single hand to operate and transport•

Speed system adjusted by rheostat, moving smoothly•

All functions are controlled by one hand. Various•

types of irregular shapes and edges cuttingare simply performedDifferent attachments are available for•

straight line cutting, circular cutting, etc.

Cutt ing Thickness 6–30mm

Cutting Speed 50–750mm/min

Power 220/50AC

Dia of Circle Cutting ƒ 50– ƒ 550mm

Dimension 455 x 400 x 225mm

Weight 9.8kg

TK-12 Beetles Portable Gas CutterThe TK-12 Beetles is a portable oxy fuel cutting machine with a high quality motor driven anda mechanical non–stage speed changer. The improved transportability will surely contributeto rationalization and labor saving of cutting operation.

The single cone system (mechanical non–stage variation device) assures constantly stable•

travel even with high temperaturesEasy operability is controlled by forward/off/reverse switch, clutch lever and speed•

adjustment knobAn adjustable radius bar for circle cutting is optionally available•

Single or Dual Torch Models, Two torch model available for parallel cutting•

2 rail suit for cutting unlimited longer part s and Groove range:•

I.Y.V. (45°)Lightness for handling and transportation•

Cutting Thickness 5~100mm (0.25~4”)

Cutting Speed 150~800mm (6~32”)/min

Speed Control Single cone system

Power 42/110/220V AC

Weight9.5kg (20.9lbs)(one torch model) 13kg(28.6lbs) (two torch model)

Size 350 x 140 x 175mm

TK-12 Max Gas CutterThe TK-12 Max is a portable flame cutting machine designed to cut straight lines, circlesand bevels with clean sharp, smooth edges providing eight standard variations of cuttingattachments. The cutting machine is intended for cutt ing materials like steel plates etc.

Excellent operability and tractive force•

Unrivaled heat–resistance and durability•

Versatility and convertibility – all types of straight line, circle, and bevel cutting•

The well–balanced center gravity ensures stable travelling•

The speed change mechanism is composed of parts designed on the basis of approx.•

5000–hour trial loaded operation particularsCutting operation can be started smoothly•

Running continuously under high temperature•


Cut ti ng Speed (S tandard type) 80~800mm (3~31”)/min

Travelling Speed (High Speed type) 240~2.400mm (9~95”)/min

Speed Control Double cone stepless speed control system

Speed Meter Dial inidication (w/ conversion scale)


Machine Dimensions

Length 600mm (24”)Width 175mm (7”)Height 228mm (9”)

Max. Loading Weight 50kg (110lbs)

Weight 15kg (33lbs)

TG2-600 Circular Gas CutterThe circular cutter TG2–600 is a portable flame cutt ing machine designed to cut circle par ts,round hole and flange, smooth edges providing two standard variations of cutting speed. Thecutting machine is intended for cutting materials like steel plates, etc.

Excellent operability and lightness•

Especially for cutting of circular parts, round hole and flange•

Cutting operation can be started smoothly•


Cutting Speed 0.2–6.0 R/P/min

Dia of cutting 30–600mm


Machine Dimensions

Length 750mm (29.5”)

Width 300mm (12”)Height 700mm (27.5”)

Weight 15kg

TG2-11D Automatic Pipe Gas CutterThe TG2–11D is a portable pipe cutting machine with a chain and gear drive system.The machine will exhibit excellent performance in straight and bevel cutting of all sizes ofpipes, which accounts for most of pipe cutting work, being habitually used by many users.Save working time by electric power.

Cuts any size pipe bigger than100mm (4’)•

Ability to cut large pipe diameters (The chain for the maximum dia is 600mm)•

Driven by motor with shift gear•

Graduated bevel collar•

Light–weight and Excellent operability•

Cutting Thickness 6mm–50mm

Pipe Cutting Diameter150~600mm (6~24”)by standard chain (2.4m = 96”) over600mm by extra chain addition

Cutting Shape I, V (up to 45°)

Drive Method Automatic

Voltage 220/110/47 AC

Weight 16kg

TG2-150B Profiling Gas CutterTheThe profiling cutter is a portable flame cutting machine designed to cut square, rectangle,smooth edges providing two standard variations of cutting speed. The cutting machine isintended for cutting materials like steel plates, etc.

Move and position freely by railway•

Excellent operability and lightness•

Cutting operation can be started smoothly•

Support Various kinds of spare parts•



Cutting Thickness 6–100mm


Dia of Circle Cutting ƒ 20–600mm

Length of Line Cutting 1200mm

Max Size of Cutting Square 500 x 500mm

Max size of Cutting Rectangle 400x900mm 450x750mm

Weight 56.5kg

TG2-11 Magnetic Pipe Gas CutterThe TG2–11 Magnetic Pipe Gas Cutter is an automatic portable gas cutting machine withpermanent magnet wheel system, can be easily set and secure on a pipe in a wide variety ofsizes. The machine will exhibit excellent performance in harsh working condition.

Can be safely fastened with the magnet wheel, compact system•

Circles can be cut in very smooth edge•

Can be working for parallel, upright and upward cutting•

Excellent for circular cutting, easy operability•

Can bevel up to 45° (IV)

Cutting Diameter >108mm


Cutting Spped MM/MIN 50–750

Power 220/50 AC


Weight 20kg

AS00632

AS00634

AS00636

AS00638

AS00639

AS00637

AS00635

AS00633

Welding Products





Gas Pipe Cutter

PIPEMATE Gas Pipe CutterAccurate square & bevel edge•

circumferential flame cutting.Designed for optimum stability.•

Designed for simple Operation.•

Fully adjustable to any cutting•

angle.Quick changeover between•

differing pipe diameter.

The Strong lightweight PIPEMATE, portbility with high cutting accuracy.

The PIPEMATE pipe cutter is one of the CIGWELD range of quality fiame cutting machine only 9kg.This hardworking unit offers troublefree maintenance, easy operation and true portability. With itsdependable chain drive, the PIPEMATE solves most circumferential cutting problems, independentof electrical supply. This machine is easily moved from job to job and is at much at home on site asin the workshop. The PIPEMATE is capable of producing square cuts and bevel edge preparationsover a wide range of pipe diameters and wall thickness.

Construction Features

Among the many advantages to this rigidly constructed machine are:Smooth, Dependable Drive

.levarthtoomsylemertxenistluseroitarraegwoleht,leehwmrowdnamrowahguorhtsievirDThe drive gear and gear chain are designed for maximum stability, thus reducing backlash ineither direction.Simplified Operational ControlThe Control valves for fuel gas, heating oxygen and cutting oxygen are located away from the heataffected zone, conveniently placed foe easy operator use,Adjustable BlowpipeUsing either CIGWELD acetylene or LPG 3 seat cutting nozzles, the cutting blowpipe may beadjusted 80mm perpendicular to the pipe surface and 120mm along the pipe surface by rackand pinion . A graduated scale ensures accurate bevel setting, and a wing nut locks the cuttingblowpipe firmly in position.

AS00136

Lightweight Portable Flame Cutting Machine

AS00139

Designed to enhance workshopefficiency, the PLATEMATE 2 iscompact and light without loss ofaccuracy or cutting capacity.

Automatically cuts straight lines,•

circles and bevelsLightweight•

Portable•

Compact construction•

Designed for simple operation•

High stability for long distance•

cutting

3 SEAT CUTTING NOZZLES

Standard Speed Acetylene

Part No. Tip Size Plate Thickness (mm)

306114 00 0 to 5

306115 0 5 to 10

306116 1 10 to 15

306117 2 15 to 30

306118 3 30 to 40

306119 4 40 to 50

Standard Speed LPG


306096 00 0 to 5

306097 0 5 to 10

306098 1 10 to 15

306099 2 15 to 30

306100 3 30 to 40

306101 4 40 to 50

SEAT CUTTING NOZZLES



5ot000411603

01ot50511603

51ot01161160303ot512711603

04ot033811603

05ot044911603



5ot000690603

01ot50790603

51ot011890603

03ot512990603

04ot033001603

05ot044101603

Specifications

Machine Part No. 338534

Pipe Diameter 100–600mm with standard chain

Pipe Wall Thickness up to 50mm

Optional Accessories

Additional 2m chain P.N. 333094

Included Accessories

Cutting Tip Acetylene Size 1 1 Pc

cP1srenaelCpiT:slooT

Spanners 3 Pc

Chain Link VersatilityThe drive chain consists of interlocking links that are easily added or removed for rapid chargesbetween pipes of different diameters.

Specifications

Machine Part No. 338536

Weight (one torch set) 9.5kg

mm053htgneL

Wheel width 160mm

Motor

Reduction gear

Model:Power Source:

Revolution:

Condenser-induction240V50Hz1500rpm(no load)Single cone system



Cutting edge shape Square cutting

V–Bevel Cutting

Rail 1.8m Log P.N.335287

Two Touch Set P.N.338538

Circle Cutting Attachment P.N.338539

Plant Includes

1 x PLATEMATE 2

1 x Cutting Torch

1 x Cutting Tip Acetylene Size 1

1 x Tip Cleaners

1 x Spanners

Pipe Mate – AS00136

Plate Mate – AS00139

Specifications

Welding Products





Cutting TorchCode No. Model

AS00140 Type 250

Welding TorchCode No. Model

AS00145 Weld Master

Welding TorchCode No. Model

AS00146 Weld Master

Tig TorchCode No. Size

AS00148 150AMP

Tig TorchCode No. Size

AS00149 200AMP

Heating TorchCode No. Model

AS00150 Weld Master

Gouging TorchCode No. Size

AS00171 400AMP

Sanritsu #8575 Electrode Holder

AS00168

Electrode HolderCode No.

AS00168

AMP

500

Code No. AMP

Gouging TorchCode No. Size

AS00172 600AMP

Welding and Cutting Set Welding and Cutting Torch

Cutting TorchCode No. Model

AS00371 Type 200

Type 23AS00152

AS00149

AS00146

AS00371

AS00148

AS00171

AS00170

AS00172

AS00145

AS00140

Heating TorchType 02AS00150

Type 21AS00153

AS00170 500AS00169 300

Welding Products





Oxygen RegulatorCode No. Model

AS00155 Oxygen

Oxygen & Actylene FlashBack Arrestor for Regulator

Code No. Model

AS00184AS00188

OxygenAcetylene

Oxygen & Actylene FlashBack Arrestor for Torch

Code No. Model

AS00175AS00179

OxygenAcetylene

Actylene RegulatorCode No. Model

AS00159 Acetylene

Argon Regulator R-11

High Pressure:250kgs/cm²Low Pressure:25 litres/min

Argon FlowMeter

Nitrogen Regulator

Oxygen & Acetylene FlashbackBack Arrestor for Hose

Code No. Model

AS00372AS00373

OxygenAcetylene

British Type HoseCheck Valve

Code No. Size

AS00391AS00392

3/8”BSP x 6mm RH3/8”BSP x 6mm LH

USA Type HoseCheck Valve

Code No. Size

AS00393AS00394

9/16” x 6mm RH9/16” x 6mm LH

Nut & Hose NippleCode No. Size

AS00387AS00388

3/8”BSP x 6mm RH3/8”BSP x 6mm LH

Hose CouplersCode No. Size

AS00389AS00390

AS00395AS00396

AS00397AS00398

9/16” x 9/16” RH9/16” x 9/16” LH

5/8”—19T x 9/16”—18T9/16”—18T x 5/8”—18T

3/4”—14T x 3/4”—14T LH3/4”—14T x 3/4”—14T RH

Carbon Dioxide Regulator

Propane Flash Back Arrestor

Inlet Connection:22mm Ø x 14th.RHExhaust Pressure:Standard 2kgs/cm

AS00155 AS00159

36100SA26100SA

AS00166

AS00179

AS00184

AS00188

AS00372 AS00373

AS00181

AS00389

AS00387AS00391 AS00393

AS00394

AS00397

AS00395

AS00175

AS00164

Welding Products





Welder FixerCode No. Size

AS00400

AS00401

AS00588

AS00589

3”

4”

5”

6”

Oxygen

AS00208

Earth Clamp

AS00190

G Type Ground Clamp

AS00193

ANME Cutting NozzleCode No. Size

AS00194

AS00195

AS00196

AS00197

AS00198

AS00199

AS00200

1/32”

3/64”

1/16”

5/64”

3/32”

7/64”

1/8”

AS00194

PNME Cutting NozzleCode No. Size

AS00201

AS00202

AS00203

AS00204

AS00205

AS00206

AS00207

1/32”

3/64”

1/16”

5/64”

3/32”

7/64”

1/8”

AS00201

Twin Outlet Valve

Acetylene

AS00209

Cable Connector Pin TypeCode No. Size

AS00210

AS00211

300AMP

500AMP AS00210

Cable Connector Screw TypeCode No. Size

AS00212

AS00213

300AMP

500AMP AS00212

Head Shield

AS00217

Hand Shield

AS00218

Welding Goggle

AS00219

Welding Spectacle

AS00220

Rock Spark Gun

AS00222AS00221

Flint Stone

3 Flint Spark Lighter

AS00224AS00223

Flint Stone

Oxygen Key

AS00225

Code No. Size

AS00190AS00191

AS00192

300AMP400AMP

500AMP

Welding Mask withSafety Cap

AS00350

American Cable Joint 500AMP

AS00351

Welding Products





Dark Glass

2” x 4”AS00228

AS00342AS00343AS00344

No 10

No 11No 12No 13

Fibreglass Tape

Size 2” x 3mm x 30mAS00374

AN00609

Fibreglass Cloth

Model No.Code No.Density

TemperatureResistance CapabilityWeave TypeColour FinishThicknessWidthRoll Length

TX3000AS002501600g/m²550°C(Max Continuously)PlainWhiteTexturised3.0mm1.0m15m

Fibreglass Cloth

Model No.Code No.

DensityTemperatureResistance Capability

Weave TypeColour FinishThicknessWidth

Roll Length

HT800AS002481650g/m²550°C(MaxContinuously)SatinGolden BrownHeat Treated1.0mm1.0m

50m

G1700AS002491100g/m²550°C(MaxContinuously)PlainGolden BrownTexturised1.7mm1.0m

30m

Clear Glass

2” x 4” AS00229

AS00247

Tempilstiks

Tempilstiks are made of materials with melting points calibrated to a guaranteed tolerance of±1%. There are a total of 103 temperature ratings with melting points systematically spacedbetween 100ºF/38ºC and 2500ºF/1371ºC. Most can be certified to be lead and sulfur free.Every Tempilstik is traceable by lot number to the specific batch of raw material from whichit was made.

Tempilstik, Tempilaq and Tempil Pellets are available in the following temperatures:

°F °C °F °C °F °C °F °C °F °C °F °C

100103106109113119125131138144

150156163169175182188194200

38394143454852555962

666973767983879093

206213219225231238244250256263

269275282288294300306313319

97101104107111114118121124128

132135139142146149152156159

325331338344350363375388400413

425438450463475488500525550

163166170173177184191198204212

218226232239246253260274288

575600625

•650

700•750

•800

•850

900932

950977

10001022

•105011001150

•1200•1250

302316329343371399427454482500

510525538550566593621649677

•1300•1350•1400

1425•1450

1480•1500

155016001650

1700•1750

18001850

•19001950200020502100

704732760774788804816843871899

927954982101010381066109311211149

•2150•2200

•2250

•2300

•2350

24002450

•2500

11771204123212601288131613431371

°Series “R” tempil Pellets available in these temperatures, 550ºF and below. Regular Pellets can be used forreducing atmospherre. Aerosol Tempilaq not available below 150ºF/66ºC.

Cable Lux

Fire Blanket

Code No. Size

AS00214AS00215AS00216

300AMP400AMP500AMP

Code No. Size(m)

AN00609

AS00214

Nozzle Cleaner

AS00227AS00226

Nozzle Cleaner (Box Type)

1.8m x 1.2m

Welding Products





AS00265

AS00266

AS00267

Pipe Cutting & Beveling Machines

Short Saddle Machines• Fast Set Up• AccurateMathey Dearman Short Saddle Pipe Cutting and Beveling Machines provides fast,clean, and accurate cuts in preperation for fitting pipe. The single piece saddlerequires less maintenance. Precision machined to provide close tolerance control ofmovements. Using a Mathey Dearman machines, you will not waste time or material.These machines have the capability to be installed either perpendicular or parallel tothe pipe. They are available in either manual or motorized form. Uses oxy -acetyleneor plasma torch. Motorized machine is recommended if a plasma torch is being used.

AS00268

Electrode OvenModels K-50

SpecificationsElectrode Capacity

Volts (Specify)WattsThermostatTemperatureInsulationInterior Dimensions

Net WeightShipping WeightShipping Dimensions

•Part-#010201 - (120V)•Part #010202 - (240V)

50 Lbs. (22.7 kg) 18” (45.7cm)

120V / 240V AC/DC150W / 150WFactory preset/Field adjusrablePreset 275˚F (135˚C) Range100˚-300˚F (50˚-150˚C)1” (2.54cm) T.I.W.6” (15.24 cm) x 18.5”(46.99cm) x 6” (15.24 cm) x 19” (48.26 cm)18 Lbs. (8.16kg)21 Lbs. (9.53kg)10.5” (26.67cm) x 9” (22.86cm) x 22.75” (57.78cm)

Electrode OvenHolding OvensModels K-200

SpecificationsElectrode CapacityVolts (Specify)WattsThermostatTemperature

InsulationInterior DimensionsNet WeightShipping WeightShipping Dimensions

•Part-#010301 - (120V)•Part #010303 - (240V)

200Ibs. (90.7kg) 18” (45.7 cm) rods120V / 240V500w / 500wFactory preset / Field adjustablePreset 275˚F (135˚C)Range 100˚-300˚F (50˚-150˚C)1” (2.54cm) Thermal Insulating Wool12.5” (31.75cm) x 12.5” (31.75cm) x 18.25” (46.35cm)53Ibs. (24.04kg)66Ibs. (29.94kg)19.5” (49.53cm) x 17.5” (44.45cm) x 27” (68.58cm)

Electrode OvenModel K-15 W/TSpecificationsElectrode CapacityVolts (Specify)WattsThermostatTemperatureInsulationInterior DimensionsNet Weight

Shipping WeightShipping Dimensions

•Part #010102-(120V) •Part #010103-(240V)

15 Ibs. (6.8kg) 18” (45.7cm) rods120V / 240V AC/DC150W / 150WFactory pretset /Field AdjustablePreset 275˚F (135˚C) Range 100˚-300˚F (50˚-150˚C)1” (2.45cm) Thermal Insulating Wool3.3”D (8.38CM) x 19”H (48.26cm)13Ibs. (5.9kg)

16Ibs. (7.3kg)10.5” (26.67cm) x 9” (22.86cm) x 22.75” (57.78cm)

Electrode OvenModels K-450

Specifications

Electrode CapacityVolts (Specify)WattsThermostatTemperature

InsulationInterior DimensionsNet WeightShipping WeightShipping Dimensions

•Part #010402 - (120V)•Part #010401 - (240V)

450Ibs. (204.1kg) 18” (45.74cm) rods120V / 240V1000W / 1000WDial adjustable120V: 150˚-550˚F (50˚-350˚C)240V:150˚-550˚F (50˚-350˚C)2” (5.08cm) Thermal Insulating Wool19.5” (49.53cm) D x 20” (50.80cm)73Ibs. (33.11kg)90Ibs. (40.82kg)26” (66.04cm) x 28” (71.12cm) x 26” (66.04cm)

Stack Kit available for stacking K-450 ovens two high.* K-450 480V single-pharse available.

AS00264

AS00261

AS00259

AS00256

Portable Electrode Dryer

Electrodes Dryer – Magnet Type

Electrodes Dryer – Wire Type

Electrodes Dryer –Temperature Control Type

Code No. Rod Length(mm)

Rod Weight(kg)

Capacity(W)

Ø x Over all Height (mm)

Weight(kg)

Remarks

AS00259 550 5 600/80 230Ø x 735H 7 Level-raising base

AS00260 750 10 800/80 230Ø x 835H 11 Inclined, with 50mmlevel-raising


Rod Weight(kg)

Capacity(W)


Weight(kg)

Remarks

AS00255 450 5 200 180Ø x 600H 3 Upright

AS00257 750 10 300 180Ø x850H 7 Inclined


Rod Weight(kg)

Capacity(W)


Weight(kg)

Remarks

AS00256 450 5 200 180Ø x 600H 3 Upright

AS00258 750 10 300 180Ø x850H 7 Inclined

AS00255

Welding Products





VESI - MAG - HOLDER

VERSI–MAG–HOLDER This tool replaces the VERSI–MAG–TOOL, Stock No. 21. New tool willcarry Stock No. 21-A. Desirable for holding welding lead or hose lengths suspended in air forstructual type work. Holds all types weldingtorches. Squared on each end and hinged to swing

90 degree angle to art as jig or line-up for small parts, welding or machinist work. Two 25lb.Pull–magnets, cast-in aluminum body with machined V-base, hinged together with pin for flat oroval surface.

AS00292

Contour Markers™

For Making off Pipe Joints and Structural Angle Cuts

No. mistakes – no loss of time – regardless of the typeor size of pipe joint to be welded – that’s just oneadvantage of the CONTOUR MARKER.™Standard for 1/2” to 18” pipe and structuralsModel including strucural adaptor …Stock No. #101

Pro–Mag–Level

This level is designed for the fitter, welder, jig builder, for any layman who has angle or settingproblems. the Pro-Mag-level is 9” in length, 2” high, 3/4” wide, weighing a total of 10oz.- aconvenient pocker size. Body of level is made of strong aluminum casting to maintain lightness oftool. (scales are imprinted on front of the tool for rise in degree per foot and degrees in rise permeter. Equipped with level and 90 degrees dial marker in 21 /2 degrees, held in place by screwwith pressure washer for easy setting. Frame of level is equipped with two magnets for holding alevel in desired position, allowing the layman a third hand. Above illustration shows tool in opera-tion in two positions.

No more “cut and try” – it eliminates the need forcalculation, and is available in two sizes for markingpipe and structurals of 11/2” to 18” in cross section,and from 8” to 48” diameter. Jombo for 8” to 48” pipe and structurals includingModel strucural adaptor ………….. Stock No. #104

AS00293

AS00294

AS00295

Wrap-A-Round

An inexpensive WRAP–A–ROUND for making straight lines around pipe or for use as a straightedge. Make out of flexible gasket material, reasonable resistant to heat and cold.

Ex-Small

SmallMediumLargeEx-LargeEx-Large

Width 1.94”xLength 2’

Width 2.5”xLength 2’Width 3.88”xLength 4’Width 3.88”xLength 6’Width 5”xLength 7’Width 5”xLength 9’

1” to 3” pipe

1” to 3” pipe3” to 6” pipe3” to 10” pipe4” to 12” pipe6” to 16” pipe2” to 30 ” pipe12” to 48” pipe

….Stock No.150B

….Stock No.126….Stock No.164B....Stock No.176B....Stock No.177B....Stock No.179B

AS00283

AS00284AS00285AS00286AS00287AS00288

Special sizes available on order, 3.88”, 5” & 7” width to any length to 375’. All Wrap-A-Roundare available in three colours to designate material type and service temperatures.G (Gray) Regular asbestos type material, up to 250 F.B (Black) Asbestos-free material, use to 325 F.W (White) Asbestors-free material (high Temp) above 350 F.

AS00283

Stock No. #108

Stock No. #107

Fitter Weld Protractor

A 90˚ protractor with matchinglocking lever to set and holdprotractor at desired angle,mounted in a 3/4” width framewith a 3/8” by 6” cast–in rod.Equipped with 5/8” by 10” armto complete finding of angles ordesired bends. Also to determineany portion of elbows or 90˚. This new tool comes with a 25# pullmagnetic base for holding protractor frame in position. Tool can be usedmanually or with magnetic base, as illustration above shows.

Centering Head

Determines Center Line at any Degree and Measures Degree of Declivity

With Dial–Set–Level and 8” Y-Type Headwith Spring Loaded Hardened Punch.

Works 1” pipe and up to large tanks.• Establish Angles and Mark for Butt-Ins• Locate Points Inside Pipe or Tanks• Set Tanks• Lay Out Keyways • Measure Declivity

Jumbo

With Dial–Set–Leveland 4” Y-Type Head

with manual operatedhardened punch.Works 1 /2” pipeand up.

Stock No. #106

Stock No. #9Standard

79200SA69200SA

AS00298

SpecialSpecial

Width 5”xLength desiredWidth 7”xLength desired

....Stock No.128..Stock No.132

AS00290

AS00291

Welding Products





Univer Level

Flange orientation and pipe leveling ang aligning are amongthe many capabilities of the UNIVERSAL LEVEL. TheCURV-O-MARK® UNIVERSAL LEVEL, the leveling tool thatpipefitters and pipe weldors have been waiting years to get theirhands on - is here! In one tool, a level, there is available all thefunctions of a leveling device, such as, the capability of levelinga run of pipe but also the capacity for accurately setting apredetermined pitch of a string of pipe, setting the angle of

dnasnurlacitrevgnieurt,eergedesicerpaotslaretal“two-holing” flanges. All because the UNIVERSAL LEVEL is flttedwith a CURV-O-MARK® protractor dial bubble. The CURV-O-MARK® UNIVERSAL LEVEL is adurable aluminum casting to make it light-weight and rust proof. There are two cast-in 25-pound-pull

magnets (exerting a 50-pound-pull) which securely hold the level in place on any steel surface; afeature that makes for “handsfree” leveling – a welcome aid in some ‘tight” spots.

Combination Adaptor AccessoryFor Contour Marker™ Jombo or Standard models

This new tool paten will prove a great advantage to the layman, allowing him to use all four sides of the CONTOURMARKER™ in lay-outs on pipe, also structural steel. It allows him to work up to 30” pipe with the Standard Modelor up to 100” pipe with the Jombo Model by quartering or halfing his pipe. With i t he can mark over nipples,oldwelds, and without having to break the wrap so far back on wrapped pipe. The ADAPTOR allows him towork compound angles in one setting of the tool, also to mark off any portion of elbows or 90 degrees he wouldso desire, as you will note self explanatory illustration above. The tool is sold by your welding distributor as anaccessory to the CONTOUR MARKER™

Standard Combination Adaptor…………........Stock No. 105 AS00299 Jumbo Combination Adaptor…………........….Stock No. 106 AS00300

00300SA99200SA

Radius Markers

THE STANDARD RADIUS MARKER folds to packet size. This sturdy, folding Radius Marker has a span of 8” for 1208, 20” for 1220, 24” for 1224and easily swings a 16”, 40”, 48” circle or arc. THE JUMBO RADIUS MARKER is also the folding type; has a span of 40” and easily swing a 80”circle. These tools are precision made of rust proof aluminum dural. The Standard Radius Marker 1224 folded, measures only 91 /4” in length, weighingonly 8 oz. The jumbo Model of course, is larger. Both are equipped with special spring washers to maintain accuracy and rigidity for years of service.Pencil holder is made to hold round or flat pencils, soapstone, or steel point.MINI………………….......……….......…....Stock No. #118 AS00301

SMALL…………….......….......………....….Stock No. #119 AS00302 AS00301

STANDARD………………..............…....….Stock No. #120 AS00303

JUMBO…………………......... .........………Stock No. #114 AS00304

Circle Ellipse Projector

This tool is designed for making perfect circles, ellipse or oblong circles. The tool will work on pipe, tanks, boilers, cones, or any irregular, flat or roundsurface. It is designed with strong magnettic base to hold in position while desired work is being performed. It also has sliding rods with protractor andlocking lever to adjust for desired lay-out, and a designed chalk holder for round or flat soapstone or will receive steel scribe or pencil. This tool worksfrom 11 /2” circles to 18” circle. Also can be adjusted from (0) to 90 degree angle. Attachment for use on large pipe available on request.Stock No. #115.. AS00305

AS00305

AS00306

Multi-Trammel Head

MULTI-TRAMMEL HEADS are diecast of strong durable, aluminum and are machine to accept standard 1 /2” pipe or bar. Weight approximately 8 oz.per set. equipped with 1 /4” thumb screws and squared on back side for perfect perpendicular aligment. One head holds 1/4” case hardened centerpoint. The movable head holds 1 /8” steel scribe, hardened to 59 rockwell. Also, the chalk holder will accept any of the marking devices illustrated inpicture. Radius setting points are cast in alighment with marking pionters for easy setting. Marks from 11 /2” circle to as large a diameter as desired,depending on length of 1 /2” pipe used for t rammel bar.Stock No. #117.. AS00306

Pipe Flange Aligners

Easily inserts itself into pipe•

Centers itself snugly against in side pipe diameter•

Automatically aligns with pipe axis.•

Faster, more accurate pipe line construction is now made easy with thisself-determining Flange Aligning Tool. Itis quickly adjustable for all typesof flanges or pipe sizes ranging from 3” to 12” in diameter.

AS00307

STANDARD MODEL……………………………Stock No. #10 AS00307

Dial Angle Flange Level

This new tool is a casting equipped with theCURV-O-MARK® protractor with level and two pinsheld to body of level on a sliding scale. The slidingscale on body allows the use of this tools on any sizeflange as you always will use the two holes closesttogether and then revolve flange to zero on any angleto which you set dial. The two threaded, self-aligningconical spacer and conical nut and bolt units aredesigned to fit any size bolt hole. This method iscommonly Known as two-holing a flange only in amore unique manner. The body of this tool is 1 /2” thick with a machined surface, therefore, allowingthe removal of pins from body and using as a regular dial degree utility level.

Stock No. #109AS00310

Stock No. #111AS00312

Welding Products



Allinton Engineering & Trading Pte Ltd

Inspection Mirrors and Pick–up Tools

UG–B06 Flexible Mirror with Light Tool

Type Dia. Length V/O Battery Packing

Oval 25 x 50mm 500mm DC 2 AA’s 1.5 Volts Sliding on card12/72pcs/2.5cuft/17.0kgs

UG–B151 Telescoping Inspection Mirror Tool

gnikcaPhtgneL.aiDepyT

Round 55mm 250 to 780mm Sliding on card25/100pcs/2.2cuft/19.0kgs



Round 38mm 115 to 510mm Sliding on card25/200pcs/1.6cuft/11.0kgs



Rectangle 50x90mm 260x810mm Sliding on card25/100pcs/2.2cuft/19.0kgs

UG–B22 Flexible Magnet Pick–up Tool

Length Pick–up Description Packing

560mm 3.5lbs PVC handle green plated,Chrone plated shank

Card25/100pcs/1.8cuft/18.0kgs

UG–B08 Telescoping Magnet Pick–up Tool

Length Pick–up Description Packing

305 to610mm

1.0lbs Ball joint allows head to swivel,Black PVC coated housing

Sliding on card24/144pcs/2.2cuft/25.0kgs

UG–B15 Magnetic Pick–up Tool Heavy Duty PocketgnikcaPhtgneLpu–kciP

3.5lbs 130 x 640mm Blister on card50/200pcs/1.0cuft/10.0kgs

UG–B455, UG–B455A & UG–B355 3 in 1 Lighted Magnetic Mirror

gnikcaPhtgneLpu–kciP

3.5lbs 130 x 640mm Blister on card50/200pcs/1.0cuft/10.0kgs

UG–B137B 2 in 1 Magnetic & Mirror

htgneL.aiDyticapaCepyT

Round 1.1lbs 32mm 250 x 500mm

UG–B2100 2 in 1 Lighted Maguetic Pick-up Tool

Capacity Description1.5lbs Telescoping handle pocket

41300SA31300SA

61300SA51300SA

81300SA71300SA

02300SA91300SA

AS00321 AS00322

Welding Products

Welding Products(Pg164-180) (1)

Documents

Transcript of Welding Products(Pg164-180) (1)