VR-6050 KRF-V7060D KRF-V6060D - KENWOODmanual.kenwood.com/files/B60-5192-10.pdf · 2010-09-17 ·...

B60-5192-10 03 MA (K, P, T, M, Y, X) 0109

AUDIO VIDEO SURROUND RECEIVER

VR-6050KRF-V7060DKRF-V6060DINSTRUCTION MANUALKENWOOD CORPORATION

About the supplied remote controlCompared to standard remote controls, the remote control supplied with this receiver has severaloperation modes. These modes enable the remote control to control other audio/video components. Inorder to effectively use the remote control it is important to read the operating instructions and obtain aproper understanding of the remote control and how to switch its operation modes (etc.).Using the remote control without completely understanding its design and how to switch the operationmodes may result in incorrect operations.

This instruction manual is for some models. Model availability and features(functions) may differ depending on the country and sales area.

•VR6050/01-09/EN 4/17/02, 6:23 PM1

2 EN

Units are designed for operation as follows.

U.S.A. and Canada ........................................... AC 120 V only

Australia ........................................................... AC 240 V only

Europe and U.K. ............................................... AC 230 V only

China and Russia ............................................. AC 220 V only

Other countries .......... AC 110-120 / 220-240 V switchable*

For the United KingdomFactory fitted moulded mains plug

1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.

2. The fuse cover must be refitted when replacing the fuse in themoulded plug.

3. Do not cut off the mains plug from this equipment. If the plug fittedis not suitable for the power points in your home or the cable is tooshort to reach a power point, then obtain an appropriate safetyapproved extension lead or adapter, or consult your dealer.If nonetheless the mains plug is cut off, remove the fuse anddispose of the plug immediately, to avoid a possible shock hazardby inadvertent connection to the mains supply.

IMPORTANT: The wires in the mains lead are coloured in accordancewith the following code:

Blue : NeutralBrown : Live

Do not connect those leads to the earth terminal of a three-pin plug.

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

Safety precautions

WARNING :TO PREVENT FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THIS APPLIANCE TORAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOTREMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTSINSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TOALERT THE USER TO THE PRESENCE OF UNINSULATED“DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S EN-CLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TOCONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRI-ANGLE IS INTENDED TO ALERT THE USER TO THE PRES-ENCE OF IMPORTANT OPERATING AND MAINTENANCE(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOM-PANYING THE APPLIANCE.

Before applying the power Caution : Read this page carefully to ensure safeoperation.

* AC voltage selectionThe AC voltage selector switch on the rear panel is set to the voltagethat prevails in the area to which the unit is shipped. Beforeconnecting the power cord to your AC outlet, make sure that thesetting position of this switch matches your line voltage. If not, itmust be set to your voltage in accordance with the following direction.

VOLTAGE SELECTORAC 110-120V~

AC 220-240V~

Note:

Our warranty does not cover damage caused by excessive linevoltage due to improper setting of the AC voltage selector switch.

AC voltage selector switch

Move switch lever tomatch your line voltagewith a small screwdriveror other pointed tool.

•VR6050/01-09/EN 4/9/02, 4:51 PM2

3 EN

ContentsCaution : Read the pages marked carefully to ensure

safe operation.

Before applying the power

Before applying the power .............................. 2Safety precautions ............................................. 2Unpacking .......................................................... 3How to use this manual ..................................... 4Special features ................................................. 5

Names and functions of parts ......................... 6Main Unit ........................................................... 6Remote control unit (RC-R0725) (KRF-V7060D)and (RC-R0727) (VR-6050/KRF-V6060D) ............... 7Remote control unit (RC-R0726) (KRF-V6060D)(For the U.K. only) .................................................. 8

Setting up the system ........................................ 9Connecting audio components ........................ 10Connecting video components ........................ 11Digital connections .......................................... 12Connecting a DVD player (6-channel input) ..... 13Connecting the speakers ................................. 14Connecting the terminals ................................ 15Connecting to the AV AUX jacks ..................... 16Connecting the antennas ................................. 16Connecting the system control ....................... 17Preparing the remote control .......................... 17

Preparing for surround sound ....................... 18Speaker settings .............................................. 18

Normal playback.............................................. 21Preparing for playback ..................................... 21Listening to a source component .................... 21Adjusting the sound ......................................... 22

Recording .......................................................... 23Recording audio (analog sources) ................... 23Recording video ............................................... 23Recording audio (digital sources) .................... 23

Listening to radio broadcasts ....................... 24Tuning (non-RDS) radio stations ...................... 24Using RDS (Radio Data System)(For the U.K. only) ............................................ 24Presetting radio stations manually .................. 24Receiving preset stations ................................ 25Receiving preset stations in order (P.CALL) ... 25Using the RDS DISP (Display) key(For the U.K. only) ................................................. 25Presetting RDS stations (RDS AUTO MEMORY)(For the U.K. only) .............................................. 26Tuning by Program TYpe (PTY search)(For the U.K. only) ............................................ 26

Ambience effects ............................................. 27Surround modes .............................................. 27Surround play ................................................... 29DVD 6-channel playback .................................. 30Convenient functions ....................................... 30

Basic remote control operations for othercomponents ....................................................... 33

Registering setup codes for othercomponents ..................................................... 33Operating other components .......................... 34Setup code chart(RC-R0727) (VR-6050/KRF-V6060D)(RC-R0725) (KRF-V7060D) ............................... 35Setup code chart(RC-R0726) (KRF-V6060D)(For the U.K. only) ............................................ 36CASSETTE deck, CD player & MD recorderoperations ........................................................ 37Other components’ operations ....................... 38

Preparations

Operations

Remote Control

AdditionalInformation

In case of difficulty .......................................... 40Specifications .................................................. 42

Unpacking

Unpack the unit carefully and make sure that all accessories are present.

FM indoor antenna (1) AM loop antenna (1)

For VR-6050/KRF-V6060D

Remote control unit (1) Batteries (R6/AA) (2)RC-R0727

For KRF-V6060D

(For the U.K. only)


For KRF-V7060D


*AC plug adaptor (2)

*Use to adapt the plug on the powercord to the shape of the wall outlet.(Accessory only for regions where useis necessary.)

If any acccessories are missing, or if the unit is damaged or fails tooperate, notify your dealer immediately. If the unit was shipped to youdirectly, notify your shipper immediately. Kenwood recommends thatyou retain the original carton and packing materials in case you need tomove or ship the unit in the future.Keep this manual handy for future reference.

•VR6050/01-09/EN 4/9/02, 4:51 PM3

4 EN

How to use this manualThis manual is divided into four sections, Preparations, Operations,Remote Control, and Additional Information.

PreparationsShows you how to connect your audio and video components to thereceiver and prepare the surround processor.Since this receiver works with all your audio and video components, wewill guide you in setting up your system to be as easy as possible.

OperationsShows you how to operate the various functions available on thereceiver.

Remote ControlShows you how to operate other components using the remote control,as well as a detailed explanation of all remote control operations. Onceyou have registered your components with the proper setup codes, you’llbe able to operate both this receiver and your other AV components (TV,VCR, DVD player, CD player, etc.) using the remote control supplied withthis receiver.

Additional InformationShows you additional information such as “In case of difficulty” (trouble-shooting) and “Specifications”.

Maintenance of the unitWhen the front panel or case becomes dirty, wipe with a soft, drycloth. Do not use thinner, benzine, alcohol, etc. for these agents maycause discoloration.

In regard to contact cleanerDo not use contact cleaners because it could cause a malfunction. Bespecially careful not to use contact cleaners containing oil, for theymay deform the plastic component.


Memory back up functionPlease note that the following items will be deleted from the unit'smemory if the power cord is disconnected from the AC outlet forapproximately 1 day.

• Power mode.• Input selector settings.• Picture output.• Speaker ON/OFF.• Volume level.• BASS, TREBLE, INPUT level.• TONE ON/OFF.• LOUDNESS ON/OFF.• Dimmer level.• MD/TAPE settings.• Listen mode setting.• Speaker settings.• SW RE-MIX ON/OFF.

• Distance setting.• Input mode setting.• Midnight mode setting.• PRO LOGIC II mode setting.• CS II mode setting.• Broadcast band.• Frequency setting.• Preset stations.• Tuning mode.• DSP mode.• ACTIVE EQ mode.• SPEAKER EQ mode.

For the U.S.A.

FCC WARNINGThis equipment may generate or use radio frequency energy. Changesor modifications to this equipment may cause harmful interferenceunless the modifications are expressly approved in the instructionmanual. The user could lose the authority to operate this equipmentif an unauthorized change or modification is made.

NOTE:This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment may causeharmful interference to radio communications, if it is not installed andused in accordance with the instructions. However, there is no guaran-tee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one ormore of the following measures:– – Reorient or relocate the receiving antenna.– – Increase the separation between the equipment and receiver.– – Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.– – Consult the dealer or an experienced radio / TV technician for help.

For the U.S.A.

Note to CATV system installerThis reminder is provided to call the CATV system installer's attentionto Article 820-40 of the NEC that provides guidelines for propergrounding and, in particular, specifies that the cable ground shall beconnected to the grounding system of the building, as close to thepoint of cable entry as practical.

As an ENERGY STAR® Partner, Kenwood Corpora-tion has determined that this product meets theENERGY STAR® guidelines for energy efficiency.This product can save energy. Saving energy re-

duces air pollution and lowers utility bills.

•VR6050/01-09/EN 4/9/02, 4:51 PM4

5 EN

Special featuresTrue home theater soundThis receiver incorporates a wide variety of surround modes to bring youmaximum enjoyment from your video software. Select a surround modeaccording to your equipment or the software you are going to play andenjoy! ¶

Dolby Digital and Dolby Digital EXThe DOLBY DIGITAL mode lets you enjoy full digital surround fromsoftware processed in the Dolby Digital format. Dolby Digital providesup to 5.1 channels of independent digital audio for better sound qualityand more powerful presence than conventional Dolby Surround.As for Dolby Digital EX, it creates six full-bandwidth output channelsfrom the 5.1 channel sources. This is done using a matrix decoder thatderives three surround channels from the two in the original recording.For best results, Dolby Digital EX should be used with movie sound-tracks recorded with Dolby Digital Surround EX.

Dolby PRO LOGIC IIDolby PRO LOGIC II, whilst totally compatible with its predecessorPRO LOGIC, provides greater advantages in surround sound. It allowsthe user to enjoy the conventional stereo or Dolby Surround with aconvincing “5.1 like” presentation. PRO LOGIC II offers special fea-tures for controlling the overall spatial, dimensionality and frontal soundfield imaging. PRO LOGIC II produces an impressive surround soundfrom video software marked and three-dimensionalspace from music CD. When listening to music, you will be able to enjoythe experience of sheer STEREO surround sound.

DTSDTS (Digital Theater System) is a 5.1 channel digital audio format thatprovides five full-spectrum channels and one low-frequency (subwoofer)channel for unprecedented clarity, optimum channel separation and a(wide) dynamic range.In the DTS mode, the 5.1 channel digital input from a DTS CD, LD orDVD disc (carrying the “DTS” marking) can be played in Digital Sur-round.Important:When a DTS disc is played on a CD, LD or DVD player, noise may beoutput from the analog output. It is recommended that you connect thedigital output of the player to the digital input of this unit.

Multi channel surround sound(SRS Circle Surround II )SRS Circle Surround II™ improves on its predecessor CS-5.1™ result-ing in the CS-6.1™ system, enabling you to listen to realistic, multi-channel, surround sound playback from a stereo source or conventionalsurround-encoded video source. You already enjoy listening to Dolbydigital sound/DTS multi-channel sound with your multi-speakers. Nowyou can listen to audio CDs, MDs, Broadcast and Home Theater usingyour multi-speakers. You will discover a new type of sound throughSRS Circle Surround II .


DSP surround modesThe DSP (Digital Signal Processor) used for this receiver incorporatesa variety of high quality adjustable sound fields, like “ARENA”, “JAZZCLUB”, “THEATER”, “STADIUM” and “DISCO”. It is compatible withalmost any kind of program source.

DVD 6-channel inputIf you own a DVD player equipped with 6-channel output, this receiverallows you to obtain the full surround sound impact of DVD sourcematerial featuring multi-channel encoding. Since the source signals aredigital and each channel is input independently, the resulting ambienceis far superior to what can be achieved with conventional surroundsound systems.

ACTIVE EQACTIVE EQ mode will produce a more dynamic sound quality in anycondition. You can enjoy a more impressive sound effect when ACTIVEEQ is turned on during Dolby Digital and DTS playback.

SPEAKER EQThe SPEAKER EQ function will automatically detect the various featuresof each speaker and effectively creates a stereoscopic sound effect.

Universal IR (InfraRed) remote controlIn addition to the basic receiver, the remote control supplied with thisreceiver can also operate almost all of your remote controllable audioand video components. Just follow the simple setup procedure toregister the components you have connected.

RDS (Radio Data System) tuner (For the U.K. only)The receiver is equipped with an RDS tuner that provides severalconvenient tuning functions: RDS Auto Memory, to automaticallypreset up to 40 RDS stations broadcasting different programs; stationname display, to show you the name of the current broadcast station;and PTY search to let you tune stations by program type.

PTY (Program TYpe) search (For the U.K. only)Tune the stations by specifying the type of program you want to hear.

•VR6050/01-09/EN 4/9/02, 4:51 PM5

6 EN

L

SL S SB SR

C R

SP MUTE OPTICAL 6CH INPUT

COAXIAL ANALOG 96kHzfs DSP MODE

DTS DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS CSII A B CLIPAUTO DETECT

AUTO

RDSPTY

MEMORYSTEREOTUNED

SWLFE

LOUDNESS SPEAKER EQ ACTIVE EQ DSP STEREO INPUT MODE DIMMER

SOUND TONE SETUP

BAND AUTO MEMORY

MULTI CONTROL LISTEN MODETUNER

MD/TAPEVIDEO 3VIDEO 2VIDEO 1

AUXCD/DVD

DSP

DTS

CSII

DOLBY DIGITAL

SPEAKER EQ

ACTIVE EQ

STANDBY

ON/STANDBY

A SPEAKERS B

POWER

PHONES

DOWN

MUTE

AV AUX

S VIDEO VIDEO L-AUDIO-R

UP

VOLUME CONTROL

STANDBYPOWER

ON/STANDBY

DVD/6CH

-ON –OFF

F ULL DIGITALD E C O D I N G

PHONO

Display

Speaker selection indicatorsInput channel indicatorsOutput channel indicators

AUTO indicatorMEMORY indicator

STEREO indicatorTUNED indicator

Names and functions of parts

Frequency displayInput displayPreset channel displaySurround mode display

Speakerindicators RDS indicators

1 POWER ON/OFF key

(For KRF-V7060D/V6060D) *Use to turn the main power ON/OFF.

2 ON/STANDBY key

(For KRF-V7060D/V6060D) *Use to turn the power ON/STANDBY whenthe POWER is turned ON.STANDBY indicator

2 POWER ON/STANDBY key

(For VR-6050) *Use to turn the power ON/STANDBY.STANDBY indicator

3 A SPEAKERS B keys ¡Use to turn the A/B speakers ON/OFF.

4 LOUDNESS key ™Use to switch the status of LOUDNESS.

5 SPEAKER EQ key ™Use to select SPEAKER EQ’s setting.

6 Surround indicators

DSP indicator ªLights when the receiver is in the DSP mode.SPEAKER EQ indicator ™Lights when the receiver is in the SPEAKEREQ mode.ACTIVE EQ indicator ™Lights when the receiver is in the ACTIVE EQmode.DOLBY DIGITAL indicator ªLights when the receiver is in the DolbyDigital mode.

Standby modeWhile the standby indicator is lit, a small amount of power is suppliedto the system to back up the memory. This is called standby mode.Under the condition, the system can be turned ON by remote controlunit.

Main unit

^ SOUND key ºUse to adjust the sound quality and the ambi-ence effects.

& BAND key ¢Use to select the broadcast band.

* AUTO key ¢Use to select the auto or manual tuningmode.

( TONE key ™Use to switch the status of TONE control.

) MEMORY key ¢§Use to store radio stations in the presetmemory and to start the Auto Memory (forthe U.K. only).

¡ SETUP key *Use to select the speakers' settings etc.

™ MMMMM/????? keys *Use for selection adjustments during SOUND,SETUP and PRESET CHANNEL functions.

£ MULTI CONTROL knob *Use to control a variety of settings.

¢ LISTEN MODE knob ªUse to select the listening mode.

∞ AV AUX (S VIDEO, VIDEO, L-AUDIO-R)

jacks ^§ AV AUX key ^

Use to switch the input to AV AUX.

DTS indicator ªLights when the receiver is in the DTS mode.CS II indicator ªLights when the receiver is in the CIRCLESURROUND II mode.

7 ACTIVE EQ key ™Use to select ACTIVE EQ’s setting.

8 DSP key ªUse to select any of the DSP mode.

9 STEREO key ºUse to switch the listen mode to STEREO.

0 INPUT MODE key 9Use to switch between the full auto, digitaland analog inputs.

! DIMMER key

Use to select the REC MODE. £Use to adjust the brightness of the display.

¤@ VOLUME CONTROL knob ¡# MUTE key ™

Use to temporarily mute the sound.$ PHONES jack ™

Use for headphone listening.% Input Selector keys ¡

DVD/6CH, CD/DVD, AUX (for VR-6050/KRF-

V6060D) or PHONO [for KRF-V7060D and

KRF-V6060D (for the U.K. only)], TUNER,

VIDEO 1, VIDEO 2, VIDEO 3, MD/TAPE

Use to select input sources.

MUTEindicator

CLIPindicator

Input modeindicators

Listen modeindicators

For VR-6050

For KRF-V7060D and

KRF-V6060D (For the U.K. only)

Connection at POWER ON/OFF key (for KRF-V7060D/V6060D)The power in this equipment will not be completely cut off from the ACwall outlet when the main switch is turned OFF.

•VR6050/01-09/EN 4/9/02, 4:51 PM6

7 EN

! TUNING 1/¡ keys ¢Use to operate the tuner mode.If CD, MD or TAPE is selected as the inputsource, these keys function as search keys.

@ DISC SKIP keyIf CD is selected as the input source, this keyfunctions as the multi-CD player disc skipkey.A/B keyIf TAPE is selected as the input source, this isA and B deck of a double cassette deck.

# DISC SEL keyUse to operate other components.INPUT SEL keyUse to operate other components.

$ INPUT SELECTOR keys [DVD/6CH, CD/DVD, AUX or PHONO (for RC-R0725 only),TUNER, VIDEO 1, VIDEO 2, VIDEO 3, MD/TAPE, AV AUX]Use to select the input sources. ¡

% LOUDNESS key ™Use to switch the status of LOUDNESS.

^ SOURCE ( ) keyUse to turn the other components ON/OFF.

& POWER ( ) key *Use to turn the receiver ON/OFF.

* RECEIVER keyUse to return to the operation of the receiver.

( LISTEN MODE %/fi keys ªUse to select the listening mode.

) ACTIVE EQ key ™Use to select ACTIVE EQ’s setting.

¡ SPEAKER EQ key ™Use to select SPEAKER EQ’s setting.

™ DSP MODE key ªUse to select any of the DSP mode.

£ MUTE key ™Use to temporarily mute the sound.

¢ VOLUME +/- keys ¡Use to adjust the receiver volume.

∞ MENU keyUse to operate other components.SOUND key ºUse to adjust the sound quality and the ambi-ence effects.

§ RETURN keyUse to operate other components.

¶ 2 keyUse to operate other components.FLIP keyUse to operate other components.

• 3/8 keyIf CD is selected as the input source, this keyfunctions as the play/pause key.If MD or TAPE key is selected as input source,this key functions as the play key.BAND key ¢Use to select the broadcast band.

ª 7 keyIf CD, MD, or TAPE is selected as the inputsource, this key functions as the stop key.AUTO key ¢Use to select the auto or manual tuningmode.

º DIMMER key ¤Use to adjust the brightness of the display.8 keyUse to operate other components.

⁄ BASS BOOST key ™Use to select the maximum adjustment set-ting for the low frequency range.

¤ TONE key ™Use to switch the status of TONE control.

1 REMOTE MODE keys (DVD, CBL, DSS/SAT, VCR, TV, OTHERS) ‹Use to select the components registered atthe respective input.

2 Numeric keys ‹Provide functions identical to those of theoriginal remote control supplied with the com-ponent you are controlling.



5 CH +/- keysUse to select the channels.¢ DVD 4 keysWhen in DVD player operations, these keysfunction as skip keys.

6 TV CONTROL keysUse when in TV operation.

7 TOP MENU keyUse to operate the DVD component.SET UP key *Use to select the speakers’ settings etc.

8 JoystickENTERUse to operate other components.MULTI CONTROL C/D *Use to control a variety of settings.Use to operate other components.P.CALL 4 /DOWN 2 and P.CALL/UP ¢3 ∞Use for selection adjustments during SOUND,SET UP and PRESET channel functions.

9 PAGE %/fi keysUse to operate the DVD component.

0 OSD keyUse to operate the DVD component.


Remote control unit (RC-R0725) (KRF-V7060D) and (RC-R0727) (VR-6050/KRF-V6060D)This remote control unit can be use not only for Kenwood products but also for other non-Kenwood products by setting the appropriate manufacturer’ssetup codes. fi

If the name of a function is different on

the receiver and on the remote control,

the name of the remote control key in

this manual is indicated in parentheses.

1

&

*

(

)

¡

™

£

¢

∞

§

¶

•

ª

º

⁄

¤

2

3

4

5

6

8

0

!

@

#

$

%

7

^

9

PHONO

For RC-R0725 only

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR TV OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND

INPUT SEL A/B AUTO 8

DVD/6CH CD/DVD AUX TUNER

VIDEO 1 VIDEO 2 MD/TAPE

LOUDNESS TONE BASS BOOST

MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE

DSP MODESTEREOINPUT MODE

SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

CBL DSS/SAT

•VR6050/01-09/EN 4/9/02, 4:51 PM7

8 EN

PAGE UP keyUse to operate the DVD component.

0 OSD keyUse to operate the DVD component.

! TUNING 1/¡ keys ¢Use to operate the tuner mode.If CD, MD or TAPE is selected as the inputsource, these keys function as search keys.

@ DISC SKIP keyIf CD is selected as the input source, this keyfunctions as the multi-CD player disc skipkey.A/B keyIf TAPE is selected as the input source, this isA and B deck of a double cassette deck.

# DISC SEL keyUse to operate other components.INPUT SEL keyUse to operate other components.

$ INPUT SEL. keys [DVD/6CH, CD/DVD,PHONO, TUNER, VIDEO 1, VIDEO 2,VIDEO 3, MD/TAPE, AV AUX]Use to select the input sources. ¡

% LOUDNESS key ™Use to switch the status of LOUDNESS.

^ SOURCE ( ) keyUse to turn the other components ON/OFF.

& POWER ( ) key *Use to turn the receiver ON/OFF.

* RECEIVER keyUse to return to the operation of the receiver.

( LISTEN MODE %/fi keys ªUse to select the listening mode.

) ACTIVE EQ key ™Use to select ACTIVE EQ’s setting.

¡ SPEAKER EQ key ™Use to select SPEAKER EQ’s setting.

™ DSP MODE key ªUse to select any of the DSP MODE.

£ MUTE key ™Use to temporarily mute the sound.

¢ VOLUME +/- keys ¡Use to adjust the receiver volume.

∞ MENU keyUse to operate other components.SOUND key ºUse to adjust the sound quality and the ambi-ence effects.

§ RETURN keyUse to operate other components.

¶ 2 keyUse to operate other components.FLIP keyUse to operate other components.

• 3/8 keyIf CD is selected as the input source, this keyfunctions as the play/pause key.If MD or TAPE key is selected as input source,this key functions as the play key.BAND key ¢Use to select the broadcast band.

ª 7 keyIf CD, MD, or TAPE is selected as the inputsource, this key functions as the stop key.AUTO key ¢Use to select the auto or manual tuningmode.

º DIMMER key ¤Use to adjust the brightness of the display.8 keyUse to operate other components.

⁄ BASS BOOST key ™Use to select the maximum adjustment set-ting for the low frequency range.

¤ TONE key ™Use to switch the status of TONE control.

1 REMOTE MODE keys (DVD, CD, CBL/SAT,VCR, TV, OTHERS) ‹Use to select the components registered atthe respective input.

2 Numeric keys ‹Provide functions identical to those of theoriginal remote control supplied with the com-ponent you are controlling.



5 CH +/- keysUse to select the channels.¢ DVD 4 keysWhen in DVD player operations, these keysfunction as skip keys.

6 TV CONTROL keysUse when in TV operation.

7 TOP MENU keyUse to operate the DVD component.SET UP key *Use to select the speakers’ settings etc.

8 JoystickENTERUse to operate other components.MULTI CONTROL C/D *Use to control a variety of settings.Use to operate other components.P.CALL 4 /DOWN 2 and P.CALL/UP ¢3 ∞Use for selection adjustments during SOUND,SET UP and PRESET channel functions.

9 RDS DISP key ∞Use for RDS function.PAGE DOWN keyUse to operate the DVD component.PTY key §Use for PTY search.


Remote control unit (RC-R0726) (KRF-V6060D) (For the U.K. only)This remote control unit can be used not only for Kenwood products but also for other non-Kenwood products by setting the appropriate manufacturer’ssetup codes. fl

If the name of a function is different on

the receiver and on the remote control,

the name of the remote control key in

this manual is indicated in parentheses.

1

&

*

(

)

¡

™

£

¢

∞

§

¶

•

ª

º

⁄

¤

2

3

4

5

6

8

0

!

@

#

$

%

7

^

9

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CD

TV

CBL/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND


DVD/6CH CD/DVD PHONO TUNER



MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE DOWNPTY

PAGE UPRDS DISP

•VR6050/01-09/EN 4/9/02, 4:51 PM8

9 EN

Make connections as shown in the following pages.When connecting the related system components, be sureto refer to the instruction manuals supplied with the compo-nents you are connecting.Do not connect the power cord to a wall outlet until allconnections are completed.

Notes1. Be sure to insert all connection cords securely. If their connections are

imperfect, sound may not be produced or there will be noise inference.2. Be sure to remove the power cord from the AC outlet before plugging

or unplugging any connection cords. Plugging/unplugging connectioncords without disconnecting the power cord can cause malfunctionsand may damage the unit.

3. Do not connect power cords from components whose power con-sumption is larger than what is indicated on the AC outlet at the rearof this unit.

Analog connectionsAudio connections are made using RCA pin cords. These cables transferstereo audio signal in an “analog” form. This means the audio signalcorresponds to the actual audio of two channels. These cables usuallyhave 2 plugs on each end, one red for the right channel and one white forthe left channel. These cables are usually packed together with thesource unit, or are available at your local electronics retailer.

Microcomputer malfunctionIf operation is not possible or an erroneous display appears, eventhough all connections have been made properly, reset the micro-computer referring to “In case of difficulty”. ‚

CAUTIONBe sure to adhere to the following, or proper ventilation will be

blocked causing damage or fire hazard.

• Do not place any objects impairing heat radiation onto the top of theunit.

• Leave some space around the unit (from the largest outsidedimension including projection) equal to or greater than, shownbelow.Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm

Setting up the system

Input mode settingsCD/DVD, VIDEO 2 and DVD/6CH inputs each include jacks for digitalaudio input and analog audio input.The initial factory settings for audio signal playback for CD/DVD,

DVD/6CH and VIDEO 2 are full auto.

To use the analog audio input for playback instead (if, for example, youhave connected a VCR to the VIDEO2 input), you must set the inputmode for the corresponding input to the analog mode.After completing connections and turning on the receiver, follow thesteps below.

INPUT MODE

Input Selector

1 Use the Input Selector keys to select CD/DVD, VIDEO 2 or

DVD/6CH.

2 Press the INPUT MODE key.

Each press switches the setting as follows:

In DTS play mode

1 FULL AUTO (digital input, analog input)2 DIGITAL MANUAL (digital input)

In CD/DVD, VIDEO 2, DVD/6CH play mode

1 FULL AUTO (digital input, analog input)2 DIGITAL MANUAL (digital input)3 6CH INPUT (DVD/6CH input)4 ANALOG (analog input)

Digital input:

Select this setting to play digital signals from a DVD, CD, or LDplayer.

Analog input:

Select this setting to play analog signals from a cassette deck, VCR,or record player.

Auto detect:

In “FULL AUTO” mode (AUTO DETECT indicator light up), thereceiver detects the digital or analog input signals automatically.Priority is given to digital signal during input mode selection. Thereceiver will select the input mode and listening mode automaticallyduring playback to match the type of input signal (Dolby Digital,PCM, DTS) and the speaker setting. The OPTICAL and COAXIALindicator on the display will light up when digital signal is detected.If the input signal is analog, the ANALOG indicator will light up.To keep the receiver set to the currently selected listening mode,use the INPUT MODE key to select “DIGITAL MANUAL” (manualsound). However, even when this setting is selected, there may becases in which the listening mode is selected automatically tomatch a Dolby Digital source signal depending on the combinationof listening mode and source signal.If the INPUT MODE key is pressed quickly, sound may not beproduced. Press the INPUT MODE key again.

•VR6050/01-09/EN 4/9/02, 4:52 PM9

10 EN

IN IN REC OUT PLAY IN

GND CD/DVD MD/TAPE

R

L

PHONO

R

L

AUX

IN

Connecting audio components


To AC wall outlet

Cassette deck orMD recorder

CD or DVD player

SYSTEM CONTROLjacks &

Shape of AC outlets

U.S.A. and Canada

Australia

IN

OUT

OUT

OUT

U.K.

Moving coil (MC) cartridgerecord player cannot be useddirectly from the receiver unit.It can only be used whenanother equalizer amplifier isconnected.

Other countries

Record player

[For VR-6050 andKRF-V6060D(except for the U.K.)]

•VR6050/10-18/EN 4/9/02, 4:52 PM10

11 EN

VIDEO 1 VIDEO 2 VIDEO 3

PLAY INPLAY INPLAY INREC OUT

S VIDEOIN

VIDEODVDIN

MONITOROUT

S VIDEO

VIDEOOUT

VIDEOIN

VIDEOIN

DVDIN

INVIDEO

MONITOROUT

VIDEO

Connecting video components

INVideo deck

Monitor TV

Audio inputsand outputs

A video component with digital audio outputs should be connected to the VIDEO 2 jacks.

VideoIN/OUT

DVD player or LD player

INVideo inputs and outputs(Yellow RCA pin cords)

OUT

OUT

S Video jacks

Video inputs(Yellow RCA pin cords)

About the S VIDEOjacks

S VIDEO

Use the S VIDEO jacks tomake connections tovideo components withS VIDEO IN/OUT jacks.

• If you use the S VIDEOjacks to connect your videoplayback components, besure to use the S VIDEOjacks when connectingyour monitor and videorecording components.

VIDEOIN

OUTDVD player or LD player

OUT

AudioIN/OUT


OUT OUT

•VR6050/10-18/EN 4/9/02, 4:52 PM11

12 EN

COAXIAL OPTICALCD/DVD

DIGITAL IN

DVD/6CH

VIDEO2

Digital connectionsThe digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD)format digital signals.If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section carefully. 9

COAXIALDIGITAL OUT(AUDIO)

DOLBY DIGITAL RFOUT (AUDIO)

LD playerPCM OUT


To connect an LD player with a DIGITAL RF OUT, connect the LD player to the KENWOOD RF digital demodulator (DEM-9991D).

Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver.

Connect the video signal and analog audio signals to the VIDEO 2 jack. (See “Connecting video components”.)

RF digitaldemodulator(DEM-9991D)(sold separately)

CD or DVD player

OPTICAL DIGITAL OUT (AUDIO)

Component with DTS,Dolby Digital, or PCMCOAXIAL DIGITAL OUT

Optical fibercable

COAXIAL DIGITAL OUT (AUDIO)

Connect the video signal and analogaudio signals to the VIDEO 2 jacks.(See “Connecting video components”.)

!

•VR6050/10-18/EN 4/9/02, 4:52 PM12

13 EN

DVD/6CH INPUTFRONT SURROUND SUB WOOFER

CENTERPLAY INPLAY IN

VIDEO 2 VIDEO 3

COAXIAL OPTICALCD/DVD

DIGITAL IN

DVD/6CH

VIDEO2

VIDEOOUT

VIDEOIN

VIDEOIN

DVDIN

INVIDEO

MONITOROUT

VIDEO

S VIDEOIN

VIDEODVDIN

VIDEOIN

MONITOROUT

S VIDEO

VIDEO

Connecting a DVD player (6-channel input)If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings” section carefully. 9

FRONTOUT L/R

S VIDEOOUT

COAXIALDIGITAL OUT(AUDIO)

DVD player

S VIDEO cord

SURROUNDOUT L/R

VIDEO OUT(Yellow RCApin cord)

CENTEROUT

SUBWOOFEROUT


•VR6050/10-18/EN 4/9/02, 5:26 PM13

14 EN

SUB WOOFER

SURROUND BACKPRE OUT

+

-

CENTERFRONT A

R R

R

L

SPEAKERS (8-16 )

GREENWHITERED

+ +--

+ +--

FRONT BR L

R L

SURROUND

BLUEGRAY


Right

Front Speakers A

Right

CenterSpeaker

Surround Speakers(Be sure to connect bothsurround speakers)

Use the FRONT SPEAKERS Bterminals if you want to connecta second front speaker system.

Power amplifier

Connecting the speakers

Left

Left

Poweredsubwoofer

SurroundBack

•VR6050/10-18/EN 4/9/02, 4:53 PM14

15 EN


Connecting the terminals

1 Strip coating. 2 Loosen.

3 Insert. 4 Secure.

1 Strip coating. 2 Push the lever.

3 Insert the cord. 4 Return the lever.

Connection of banana plugs (For the U.S.A. and Canada)1 Secure. 2 Insert.

• Sound will not be heard if the speaker terminal is not fully secured.

• Never short circuit the + and – speaker cords.• If the left and right speakers are connected inversely or the speaker

cords are connected with reversed polarity, the sound will beunnatural with ambiguous acoustic imaging. Be sure to connect thespeakers correctly.

Speaker impedanceAfter confirming the speaker impedance indications printed on therear panel of the receiver, connect speakers with matching imped-ance ratings. Using speakers with a rated impedance other than thatindicated on the rear panel of the receiver could result in malfunctionsor damage to the speakers or receiver.

Speaker placement

Front speakers : Place at the front left and right of the listeningposition. Front speakers are required for all surround modes.Center speaker : Place front and center. This speaker stabilizes thesound image and helps recreate sound motion. Required for surroundplayback.Surround speakers : Place at the direct left and right, or slightlybehind, the listening position at even heights, approximately 1 meterabove the ears of the listeners. These speakers recreate soundmotion and atmosphere. Required for surround playback.Subwoofer : Reproduces powerful deep bass sounds.Surround back speaker : Place the speaker directly at the rear of thelistening position. The optimum position depends mainly on the roomcondition.

• Although the ideal surround system consists of all the speakerslisted above, if you don't have a center speaker or a subwoofer, youcan divide those signals between the available speakers in thespeaker settings steps to obtain the best possible surround repro-duction from the speakers you have available. *

Channel space switching(Except for the U.S.A., Canada, U.K., and Australia)

The space between radio channels has been set to the one thatprevails in the area to which the system is shipped. However, if thecurrent channel space setting does not match the setting in the areawhere the system is to be used, for instance when you move fromarea 1 or area 2 shown in the following table or vice versa, properreception of AM/FM broadcasts cannot be expected. In this case,change the channel space setting in accordance with your area byreferring to the following table.

Area CHANNELSpace Frequency

1 U.S.A., Canada and South FM: 100 kHzAmerican countries AM: 10 kHz

2 Other countries FM: 50 kHzAM: 9 kHz

50us AM 9kHz FM50kHz


DE-EMPHASISCHANNEL SPACE

DE-EMPHASISCHANNEL SPACE



Turn the power OFF by pressing the POWER key before moving theswitch level. Move switch lever to match your area with a smallscrewdriver or other pointed tool, then turn the power on again.

Center speaker

SubwooferFront speakers(L,R)

Surroundspeakers(L,R)

Listeningposition

Surroundback speaker

•VR6050/10-18/EN 4/9/02, 4:53 PM15

16 EN

S VIDEO OUT

S VIDEO cord

VIDEO OUT

AUDIO OUT

Connecting the antennasAM loop antennaThe supplied loop antenna is for use indoors. Place it as far as possiblefrom the receiver, TV set, speaker cords and power cord, and adjust thedirection for best reception.

AM antenna terminal connections1 Push lever. 2 Insert cord. 3 Release lever.

FM indoor antennaThe supplied indoor antenna is for temporary use only. For stable signalreception we recommend using an outdoor antenna. Disconnect theindoor antenna when you connect one outdoors.

FM antenna terminal connectionsInsert cord.

FM outdoor antennaLead the 75Ω coaxial cable connected to the FM outdoor antenna into theroom and connect it to the FM 75Ω terminal.

FM75

GND

AM

ANTENNA

AM loop antenna

FM indoor antenna

Use an antennaadaptor(Commerciallyavailable)

Attach to the stand


Connecting to the AV AUX jacksThe AV AUX jacks are convenient for connection of video componentssuch as a camcorder or a video game.

S VIDEO VIDEO L-AUDIO-R

AV AUX

• To select the source connected to the AV AUX jacks press AV

AUX key. ¡• When you connect the audio source such as the MD player, you

do not need to connect the video cable.

• When you connect the unit and the component with the S

VIDEO cord, you can get better picture quality.

Camcorder, other VCR,video game, digital camera,or portable MD player

FM outdoor antenna

•VR6050/10-18/EN 4/9/02, 4:53 PM16

17 EN

Connecting the system control

Connecting system control cords after connecting a KENWOODaudio component system lets you take advantage of convenientsystem control operations.

This unit is compatible only with the [SL-16] mode. The systemcontrol operation is not available if the unit is connected in the[XS8], [XS], or [XR] connection mode.

If your component has the mode select switch, set the connectedcomponents to the [SL16] mode.

SYSTEM CONTROL

• You may connect the system control cord to either the up or down jack.

EXAMPLE: [SL16] mode connectionsThe underlined portion represents the setting of the system control mode.

[SL16] Receiver

[SL16] [XS] [XS8] [XR]Cassette deckor MD recorder

[SL16] [XS] [XS8] CD player

[XS] Record player

• In order to take advantage of the system control operations, thecomponents must be connected to the correct jacks. To use a CDplayer it must be connected to the CD jacks. To use a cassette deck(or MD recorder) it must be connected to the MD/TAPE jacks. Whenusing more than one CD player (etc.) only the one connected to thespecified jacks may be connected for system control.

• Some CD players and cassette decks are not compatible with the[SL16] system control mode. Do not make system connections withequipment that is not [SL16] compatible.

• Some MD players are not system control compatible. You cannotmake system control connections to this kind of equipment.

Notes1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8]

equipment for system operations. If your equipment consists ofthis kind of combination, please do not connect any system con-trol cords. Even without system control cords, normal operationscan be carried out without effecting performance.

2. Do not connect system control cords to any components otherthan those specified by KENWOOD. It may cause a malfunctionand damage your equipment.

3. Be sure the system control plugs are inserted all the way in to thesystem control terminals.

SYSTEMCONTROLcord

SYSTEM CONTROL OPERATIONSRemote ControlLets you operate this unit with the system remote supplied with thereceiver.

Automatic OperationWhen you start playback from a source component, the input selectoron this unit switches to that component automatically.

Synchronized RecordingLets you synchronize recording with the start of playback whenrecording from CD, MD or analog discs.

Registering setup codes for KENWOOD audio componentsIf you own remote controllable KENWOOD audio components thatare not compatible with system control, registering the setup codeenables you to control those components using the remote controlsupplied with this unit (without connecting system control cords). Toregister setup codes for your remote controllable KENWOOD audiocomponents, see “Registering setup codes for other components”.

‹


SYSTEM CONTROLcord

Preparing the remote control

Loading the batteries1 Remove the cover. 2 Insert the batteries.

3 Close the cover.

• Insert two AA-size (R6) batteries as indicated by the polarity markings.

OperationWhen the STANDBY indicator is lit, the power turns ON when you pressthe POWER key on the remote control. When the power comes ON,press the key you want to operate.

6 m

POWER

• When pressing more than one remote control key successively, pressthe keys securely by leaving an interval of 1 second or more betweenkeys.

Notes1. The supplied batteries may have shorter lives than ordinary batteries

due to use during operation checks.2. When the remote-controllable distance gets shorter than before, re-

place both batteries with new ones.3. Placing the remote sensor in direct sunlight, or in direct light from a

high frequency fluorescent lamp may cause a malfunction.In such a case, change the location of the system installation to pre-vent malfunction.

Operating range(Approx.) Remote sensor

Infrared ray system

•VR6050/10-18/EN 4/9/02, 4:53 PM17

18 EN

Preparing for surround sound

Speaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.

POWER ON/STANDBY

(VR-6050) /ON/STANDBY

(KRF-V7060D/V6060D) SETUP MULTI CONTROL

POWER ON/OFF(KRF-V7060D/V6060D)

POWER

SET UPJoystick(MULTI CONTROL5 /∞,DOWN2 / UP3)

1 Turn on the power to this receiver by pressing the POWERON/STANDBY (for VR-6050) or POWER ON/OFF and ON/STANDBY (KRF-V7060D/V6060D) or POWER key.

2 Press the SETUP key to enter the SET UP mode and pressMMMMM/????? keys or Joystick (2/ 3) for the following displays.

1 SP SETUP

2 TEST TONE

3 SP DISTANCE

4 DISP MODE

5 EXIT

The flow of the SET UP is as follows:

SP SETUP TEST TONE SP DISTANCE EXITDISP MODE

Front Left

Center

Front Right

Surround Right

Surround Back

Surround Left

Subwoofer

Display Selector

Display Listen

Subwoofer

Front

Center

Surround

SurroundBack

SurroundMix

SubwooferRe-mix

T. TONEMANUAL

T. TONEAUTO

LCR

SR

SLSB

SW

L

C

R

SR

SL

SW

SB

3 Select a speaker system.

1 Select the SP SETUP and press the SETUP key again so

that the subwoofer setting indication “SUBW ON” appears.

L

SL S SB SR

C R


COAXIAL ANALOG 96kHzfs

CINEMA EQ.ACTIVE EQ.DSP MODE

DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6

CSII A B CLIPAUTO DETECT THX

AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

2 Use the MULTI CONTROL knob or Joystick (5/∞) to select

the appropriate subwoofer setting.

1 SUBW ON : Subwoofer setting mode to the receiver isON.

2 SUBW OFF : Subwoofer setting mode to the receiver isOFF.

• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the front speakers

are automatically set to “FRNT LARGE” and the procedure skipsto step 6.Before step 6, press the SETUP key to accept the setting.

• When subwoofer output sound is required, select “FRNTNORMAL” or select both “FRNT LARGE” and “SW RE-MIX ON”.

3 Press the MMMMM key or Joystick (3) to accept the setting.

• The front speakers setting indication “FRNT” appears.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE


the appropriate front speakers setting.

1 FRNT LARGE : Large front speakers are connectedto the receiver.

2 FRNT NORMAL : Average size front speakers are con-nected to the receiver.

• For “FRNT LARGE” selection, no sound will be heard fromsubwoofer speaker even when it is set to ON. However, if youselect “SW RE-MIX ON” when subwoofer is selected, you willbe able to hear sound from the subwoofer.When in STEREO mode, the sound goes directly to frontspeaker.

5 Press the MMMMM key or Joystick (3) to accept the setting.

• The center speaker setting indication “CNTR” appears.


the appropriate center speaker setting.

If you selected “LARGE” as the front speakers setting,

1 CNTR LARGE : A large center speaker is connectedto the receiver.

2 CNTR NORMAL : An average size center speaker isconnected to the receiver.

3 CNTR OFF : Center speaker setting mode to thereceiver is OFF.

If you selected “NORMAL” as the front speakers setting,

1 CNTR ON : Center speaker setting mode to the re-ceiver is ON.

2 CNTR OFF : Center speaker setting mode to the re-ceiver is OFF.

7 Press the MMMMM key or Joystick (3) again to accept the setting.

• The surround speaker setting indication “SURR” appears.


the appropriate surround speaker setting.

If you selected “LARGE” as the center speaker setting,

1 SURR LARGE : Large surround speakers are con-nected to the receiver.

2 SURR NORMAL : Average size surround speakers areconnected to the receiver.

3 SURR OFF : Surround speaker setting mode tothe receiver is OFF.

•VR6050/10-18/EN 4/9/02, 4:53 PM18

19 EN


If you selected other than “LARGE” as the center speaker

setting,

1 SURR ON : Surround speaker setting mode to the re-ceiver is ON.

2 SURR OFF : Surround speaker setting mode to the re-ceiver is OFF.

• When the setting “SURR OFF” is selected, the procedure skipsto step #.

9 Press the MMMMM key or Joystick (3) again to accept the setting.

• The surround speaker setting indication “SB” appears.


appropriate surround back speaker setting.

If you selected “LARGE” as the surround speaker setting,

1 SB NORMAL : Average size surround back speaker isconnected to the receiver.

2 SB LARGE : Large surround back speaker is connectedto the receiver.

3 SB OFF : Surround back speaker setting mode tothe receiver is OFF.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

If you selected “NORMAL” as the surround speaker setting,

1 SB ON : Surround back speaker setting mode to thereceiver is ON.

2 SB OFF : Surround back speaker setting mode to thereceiver is OFF.

! Press the MMMMM key or Joystick (3) again to accept the setting

and “SURR:MIX” appears.

• Surr:mix is when the SL and SR speakers signals are mixed toproduce sound from the surround back speaker which wouldenable the listener to enjoy sound coming from the back.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

@ Use the MULTI CONTROL knob or Joystick (5/∞) to select

the following.

1 SURR:MIX ON : Surround mix setting mode to thereceiver is ON.

2 SURR:MIX OFF : Surround mix setting mode to thereceiver is OFF.

• If surround back speaker is turned OFF, SURR:MIX setting is notvisible and the procedure skips to step #.

# Press the MMMMM key or Joystick (3) again to accept the setting.

• The subwoofer re-mix setting indication “SW RE-MIX” appears.

$ Use the MULTI CONTROL knob or Joystick (5/∞) to select

the appropriate subwoofer re-mix setting.

1 SW RE-MIX ON : Subwoofer re-mix setting mode tothe receiver is ON.

2 SW RE-MIX OFF : Subwoofer re-mix setting mode tothe receiver is OFF.

• If subwoofer is turned OFF, subwoofer re-mix setting is notvisible.

% Press the SETUP key again to return to the main setup

displays.

• The receiver enters the speaker volume level adjustment mode.• In steps 4 and 5, indications appear only for the selected

channels of the speakers that require adjusting.

4Adjust the speaker volume level.

From your usual listening position, adjust the volume levels. Thevolume levels from each speaker should be the same.

1 Press the MMMMM/????? keys or Joystick (2/3) to select TEST TONE.

2 Press the SETUP key for the following displays:

1 T.TONE AUTO

2 T.TONE MANUAL

3 The selection of AUTO/MANUAL TEST TONE is done by the

MULTI CONTROL knob or Joystick (5/∞).

Press the SETUP key again to begin TEST TONE.

Use the MULTI CONTROL knob or Joystick (5/∞) to adjust

the volume level of the test tone output from the speaker

channel to be adjusted.

For AUTO selection, the first test tone is heard from the front

left speaker for 2.5 seconds. The next test tone is heard from

the speakers in the following sequence for 2 seconds each.

LEFT CNTR RIGHT

SRSBSLSUBW

The channel indication blinks while the test tone is being output.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. º

• If the speaker setting selects are OFF, the speaker level settingsare reset.

For MANUAL selection, press the MMMMM/????? keys or Joystick (2/3)

each time to select the speaker channel.

4 Press the SETUP key again.

• The test tone is turned off and return to the main setup displays.

5 Input the distance to the speakers.

1 Press the MMMMM/????? keys or Joystick (2/3) to select the SP

DISTANCE on setup displays and press the SETUP key again.

2 Measure the distance from the listening position to each of

the speakers.

Jot down the distance to each of the speakers.

Distance to Front left speaker (L) : ____ feet (meters)Distance to Center speaker (C) : ____ feet (meters)Distance to Front right speaker (R) : ____ feet (meters)Distance to Surround right (SR) : ____ feet (meters)Distance to Surround back (SB) : ____ feet (meters)Distance to Surround left (SL) : ____ feet (meters)Distance to Subwoofer (SW) : ____ feet (meters)

3 Use the MMMMM/????? keys or Joystick (2/3) to select the speakers

and the MULTI CONTROL knob or Joystick (5/∞) to adjust

the distance to the front speakers.

The speaker indicator to be adjusted blinks.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),adjustable in 1 foot (0.3 m) increments.

4 Repeat steps 3 to input the distance for each of the speakers.

Indication in feet Indication in meters

Continued to next page

•VR6050/19-27/EN 4/9/02, 4:54 PM19

20 EN

5 Press the SETUP key again to return to main setup displays.

• The speakers you have selected should appear on the display.Confirm that all the speakers have been correctly selected.

6 Select the display mode.

1 Press the MMMMM/????? keys or Joystick (2/3) to select the DISP

MODE.

2 Press the SETUP key for the following displays:

1 DISP SELECTOR : Displays the current input selector.2 DISP LISTEN : Displays the current listen mode.


the display mode.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

4 Press the SETUP key again to accept the setting.

5 Use the MMMMM key or Joystick (3) to select EXIT.

L C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

6 Press the SETUP key to exit the SET UP mode.


Input level adjustment (analog sources only)If the input level of an analog source signal is too high, the CLIP indicatorwill blink to indicate the source signal. Adjust the input level.

L

SL S SB SR

C R



CINEMACTIVDSP MA B CLIP

AUTO DETECT

SWLFE

CLIPCLIP

1 Use the Input Selector keys to select the source of which the

input level you want to adjust.

• You can store a separate input level for each input source.

2 Press the SOUND and MMMMM/????? keys or Joystick (2/3) repeatedly

until the “INPUT” indication appears.

3 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the

input level.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

• The adjustment mode is displayed for approximately 8 seconds.• The input level may be adjusted to any one of three settings:

0dB, -3dB, and -6dB. (The initial setting is 0dB.)

4 Press the SOUND key again to return to the input indication.

•VR6050/19-27/EN 4/9/02, 4:54 PM20

21 EN

Listening to a source component

VOLUME CONTROL

VOLUME /

INPUT SELECTOR

Input Selector AV AUX

1Use the Input Selector and AV AUX keys to select thesource you want to listen to.

Selecting a source using each key.

VR-6050/KRF-V7060D/V6060D

1 “DVD/6CH”

2 “CD/DVD”

3 “AUX” or “PHONO” (for KRF-V7060D only)

4 “TUNER”

5 “VIDEO 1”

6 “VIDEO 2”

7 “VIDEO 3”

8 “MD/TAPE”

9 “AV AUX”

KRF-V6060D (for the U.K. only)

1 “DVD/6CH”

2 “CD/DVD”

3 “PHONO”

4 “TUNER”

5 “VIDEO 1”

6 “VIDEO 2”

7 “VIDEO 3”

8 “MD/TAPE”

9 “AV AUX”

2 Start playback from the selected source.

3Use the VOLUME CONTROL knob or VOLUME +/- keys toadjust the volume.

Normal playback

Preparing for playbackSome preparatory steps are needed before starting playback.

INPUT MODE

MD/TAPEPOWER ON/OFF(KRF-V7060D/V6060D)

A SPEAKERS B

POWER ON/STANDBY

(VR-6050)

ON/STANDBY (KRF-V7060D/V6060D)

Turning on the receiver1 Turn on the power to the related components.

2 Turn on the power to this receiver by pressing the POWER

ON/STANDBY (for VR-6050) key or POWER ON/OFF and

ON/STANDBY (for KRF-V7060D/V6060D) key.

Selecting the input modeIf you have selected a component connected to the CD/DVD, VIDEO 2

or DVD/6CH jacks, make sure that the input mode setting is correct forthe type of audio signal to be used. 9

Selecting MD/TAPESelect the source name corresponding to the component connected tothe MD/TAPE jacks. The initial factory setting is “TAPE”. To change thesource to “MD”, follow the steps below:

Hold down the MD/TAPE key for more than 2 seconds.

• The source indication changes to “MD”.• To return to the original indication, repeat the above procedure.

Selecting the speaker systemPress the A SPEAKERS B key to select the speaker system to be

used.

A ON : Sound from the speakers connected to the SPEAKERS A

terminals on the rear panel.B ON : Sound from the speakers connected to the SPEAKERS B

terminals on the rear panel. No sound will be heard fromthe subwoofer.

A+B ON : Sound from both the speakers connected to theSPEAKERS A and B terminals on the rear panel.

A+B OFF : No sound from the speakers. Use this setting whenlistening with headphones for stereo sound in all playbackmodes. The display segments are different depending onthe type of input signal.

The indicator for the speakersyou want to use should be lit.

L

SL S SB SR

C R



CINEMACTIVDSP MA B CLIP

AUTO DETECT

SWLFE

• Selecting “6CH INPUT” by pressing the INPUT MODE key, whereby“DVD/6CH” is the input source will cause SPEAKERS A to be selectedautomatically.

•VR6050/19-27/EN 4/9/02, 4:54 PM21

22 EN

Muting the soundThe MUTE key lets you mute the sound of the speakers.

Press the MUTE key.

L

SL S SB SR

C R

MUTE OPTICAL 6CH INPUT


CINEMA EQ.ACTIVE EQ.DSP MODE DA B CLIP

AUTO DETECT

SWLFE

SP

Blinks

To cancelPress the MUTE key again so that the “MUTE” indicator goes off.• MUTE ON can also be deactivated by turning the VOLUME

CONTROL knob or pressing VOLUME +/– keys.

ACTIVE EQ modeYou can enjoy a more impressive sound effect when ACTIVE EQ isturned ON during Dolby Digital and DTS playback and, when in PCM andanalog stereo mode.

Press the ACTIVE EQ key for the following selections;

1 ACTIVE EQ MUSIC : Effective when listening to music.(The ACTIVE EQ indicator lights up.)

2 ACTIVE EQ CINEMA : Effective when watching a movie.(The ACTIVE EQ indicator lights up.)

3 ACTIVE EQ TV : Effective when watching TV.(The ACTIVE EQ indicator lights up.)

4 ACTIVE EQ OFF : The ACTIVE EQ function is turned OFF.(The ACTIVE EQ indicator goes off.)

• “ACTIVE EQ” will scroll from right to left.• When ACTIVE EQ and SPEAKER EQ are OFF and ACTIVE EQ

(MUSIC) is turned ON, SPEAKER EQ (SMALL) will turn ONautomatically.

• ACTIVE EQ function will not be available when REC MODE, AUTOTUNING or PRESET MEMORY is ON, and during 96kHz LPCM playback.

SPEAKER EQ modeSPEAKER EQ’s function will automatically detect the various features ofeach speaker and effectively creates a stereoscopic sound effect.

Press the SPEAKER EQ key to switch the following setting;

1 SPEAKER EQ SMALL : To select a small size speaker.(The SPEAKER EQ indicator lights up.)

2 SPEAKER EQ NORMAL : To select an average size speaker.(The SPEAKER EQ indicator lights up.)

3 SPEAKER EQ LARGE : To select a large size speaker.(The SPEAKER EQ indicator lights up.)

4 SPEAKER EQ OFF : The SPEAKER EQ function is turnedOFF.(The SPEAKER EQ indicator goes off.)

• “SPEAKER EQ” will scroll from right to left.• SPEAKER EQ cannot be turned OFF when ACTIVE EQ is turned ON.• SPEAKER EQ function will not be available when REC MODE, AUTO

TUNING or PRESET MEMORY is ON, and during 96kHz LPCM playback.

Listening with headphones1 Press the A and B Speaker keys so that the speaker indicator

goes off.

Make sure the SPEAKERSindicators are turned off.

SL S SB SR



CINEMA EQ.ACTIVE EQ.DSP MODE DA B CLIP

AUTO DETECT

LFE

• If you turn off all of the speakers when in surround mode, the surroundmode will be canceled as well, resulting in stereo playback.

2 Connect headphones to the PHONES jack.PHONES

3 Use the VOLUME CONTROL knob or VOLUME +/– keys to adjustthe volume.

Normal playback

Adjusting the sound

LOUDNESSTONE

BASS BOOST

TONE

VOLUME CONTROL

MUTE

A SPEAKERS BSPEAKER EQ ACTIVE EQ

PHONES LOUDNESS

MULTI CONTROL

VOLUME /

POWER

SPEAKER EQACTIVE EQ

MUTE

Joystick(MULTI CONTROL5 /∞,DOWN2 / UP3)

Adjusting the TONEYou can adjust the sound quality when the receiver is in the PCM stereoand analog stereo mode.

1 Press the TONE key to select the TONE mode.

2 Use the MULTI CONTROL knob or Joystick (5/∞) to select TONEON/OFF.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

3 When in TONE ON selection, press the TONE key for the followingdisplays.

BASS : Select this to adjust the low frequency range.TREBLE : Select this to adjust the high frequency range.

4 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust thesound quality.

L

SL S SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

• The bass and treble levels are adjustable from -10 to +10 in 2 stepincrements.

• The adjustment item is displayed for approximately 8 seconds.

Once-touch low frequency emphasis (BASS BOOST)(remote control only)You can adjust the sound quality when the receiver is in the PCM stereoand analog stereo modes.

Press the BASS BOOST key.• Press the key once to select the maximum (+10) low frequency

emphasis setting.• This key does not function when the receiver is in the sound quality

or ambience effects adjustment mode.

Switching back to the previous settingPress the BASS BOOST key again.

Adjusting the LOUDNESS modeYou can adjust the Loudness function which controls the low volumesettings to maintain the music's richness. The adjustment can be madewhen the receiver is in the PCM stereo and analog stereo mode.

Press the LOUDNESS key to turn the LOUDNESS setting ON.

To cancelPress the LOUDNESS key again so that the “LOUDNESS” indicatorgoes off.

•VR6050/19-27/EN 4/9/02, 4:55 PM22

23 EN

Recording audio (analog sources)

MD/TAPE

Recording a music source1 Use the Input Selector keys to select the source (other than “MD/

TAPE”) you want to record.

2 Set the MD or TAPE recorder to record.

3 Start playback, then start recording.

Recording video1 Use the Input Selector keys to select the video source (other than

“VIDEO 1”) you want to record.

2 Set the video deck connected to VIDEO 1 to record.

• Select the REC MODE to record a digital input source.


• Recording may not be normal for some video software. This is dueto the copy guard condition. ‚

Recording audio (digital sources)Switch on the REC MODE to record a digital input source.Usually use the AUTO REC MODE to record audio input sources. Whenthe digital mode changes during recording in the AUTO REC MODE, theaudio input source may be interrupted momentarily.

Recording music in AUTO REC or MANUAL REC mode

Input Selector

DIMMER

1 Use the Input Selector keys to select the source (CD/DVD,

DVD/6CH, VIDEO 2) you want to record.

2 Set the MD or TAPE recorder to record.

Recording

3 Press and hold the DIMMER key for more than 2 seconds to

select the AUTO REC or MANUAL REC mode.

1 REC MODE off : The digital input record mode isswitched off.

2 AUTO REC mode : The digital input signals (DTS, DolbyDigital, or PCM) are identified auto-matically and converted into stereosignals that are ready for recording.

3 MANUAL REC mode : The input signal type at the momentthis mode is selected is held through-out this mode.

For AUTO REC mode :

L

S SBSL SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

↓

L

S SB

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

SL SR

For MANUAL REC mode :

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

↓

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX


• If the audio reproduction stops in the middle due to change in theinput signals, etc., press the DIMMER key.

•VR6050/19-27/EN 4/9/02, 4:55 PM23

24 EN

(For the U.K. only)Using RDS (Radio Data System)

RDS is a system that transmits useful information (in the form of digitaldata) for FM broadcasts along with the broadcast signal. Tuners andreceivers designed for RDS reception can extract the information fromthe broadcast signal for use with various functions, such as automaticdisplay of the station name.

RDS functions:PTY (Program TYpe Identification) Search §Automatically tunes to a station that is currently broadcasting thespecified program type (genre).

PS (Program Service Name) Display

Automatically displays the station name transmitted by the RDSstation.

RDS AUTO MEMORY function §Automatically selects and stores up to 40 RDS stations in the presetmemory.If fewer than 40 RDS stations have been stored in the preset memory,regular FM stations will be stored in the remaining places.

Radio Text function

Displays the radio text data transmitted by some RDS stations whenyou press the RDS DISP (display) key. There is “NO RT” if no textdata is transmitted.The “RDS” indicator lights up when an RDS broadcast (signal) isreceived.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RTY

MEMOSTEREOTUNED

Surround EXRDS

NoteSome functions and function names may differ for certain countriesand areas.

Before using a function utilizing the RDS, be sure to perform the RDSAuto Memory operation by referring to the description in “PresettingRDS stations (RDS AUTO MEMORY)”. §

Presetting radio stations manuallyThe RDS auto memory function assigns preset numbers to RDS stationsstarting from preset number “1”. Therefore, be sure to execute the RDSauto memory function before using the following operations to manuallystore AM stations and other FM stations, and RDS stations. See“Presetting RDS stations (RDS AUTO MEMORY)”. (For the U.K. only)

§

MULTI CONTROL

MEMORYTUNER

1 Tune to the station you want to store.

2 Press the MEMORY key while receiving the station.

Blinks for 5 seconds Lights for 5 seconds

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

STEREOTUNED

Surround EX

MEMORY

Listening to radio broadcasts

The receiver can store up to 40 stations in the memory and recall themby one-touch operation.Radio stations can be classified into RDS (Radio Data System) stationsand other stations. To listen to or store RDS stations in the presetmemory see “Using RDS (Radio Data System)”. (For the U.K. only)

Tuning (non-RDS) radio stations

BAND MULTI CONTROL

TUNER AUTO

Joystick(MULTI CONTROL5 /∞)

AUTO

TUNING 1/¡

TUNERBAND

1Use the TUNER key to select the tuner.

2Use the BAND key to select the desired broadcast band.

Each press switches the band.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

3Use the AUTO key to select the desired tuning method.

Each press switches the tuning method to either auto or manual

tuning.

“AUTO” indicator lights up in the display.ICAL 6CH INPUT

XIAL ANALOG 96kHzfs


DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6

CSII

AUTO DETECT THX RDSRTY

MEMOSTEREOTUNED

Surround EX

AUTO

• Normally, set to “AUTO” (auto tuning). If the radio waves are weakand there is a lot of interference, switch to manual tuning. (Withmanual tuning, stereo broadcasts will be received in monaural.)

4Use the MULTI CONTROL knob or Joystick (5/∞), or TUNING1 / ¡ keys to select the station.“STEREO” lights when a broadcast is being received in stereo.

CAL 6CH INPUT

XIAL ANALOG 96kHzfs


DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6

CSII

AUTO DETECT THX

AUTO

RDSRTY

MEMO

Surround EX

STEREOTUNED

“TUNED” is displayed when a station is received.

Auto tuning : The next station is tuned automatically.Manual tuning : Turn the knob or use the Joystick (5/∞) to

select the desired station.

•VR6050/19-27/EN 4/9/02, 4:55 PM24

25 EN


Proceed to step 3 within 5 seconds.

(If more than 5 seconds elapse, press the MEMORY key again).

3 Use the MULTI CONTROL knob or Joystick (5/∞) to selectone of the station presets (1 – 40).

4 Press the MEMORY key again to confirm the setting.

• Repeat steps 1, 2, 3, and 4 to store as many stations asnecessary.

• If you store a station at a previously used preset, the old station willbe replaced by the new one.

Receiving preset stations

TUNER

Numeric keys

1 Press the TUNER key to select tuner as the source.

2 Enter the number of the preset station you want to receive(up to “40”).

Press the numeric keys in the following order:

For “15”, press 0,5For “20”, press 0,0,)

• If you make a mistake entering a two digit number, press the +10

key repeatedly to return to the original display and start again.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

Receiving preset stations in order (P.CALL)

Joystick(P.CALL 4/¢)

TUNER

1 Press the TUNER key to select the tuner as the source.

2 Use the Joystick to adjust the P.CALL 4/ ¢ direction toselect the desired station.

• Each time you push the Joystick, another preset station is receivedin order.

Pushing the Joystick to P.CALL ¢ does the following:

Pushing the Joystick to P.CALL 4 does the following:

Holding the Joystick on ¢ or 4 direction, lets you skip

through the presets, receiving each preset station at 0.5 second

intervals.

(For the U.K. only)Using the RDS DISP (Display) key

TUNER

RDS DISP

Pressing the RDS DISP key changes the contents of thedisplay.

Each press switches the display mode as follows :

1 PS (Program Service name) display

2 RT (Radio Text) display

3 Frequency display

1 PS (Program Service name) display :

The station name is displayed automatically when an RDS broadcastis received.If no PS data was sent, “NO PS” is displayed.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

2 RT (Radio Text) display :

Text data accompanying the RDS broadcast scrolls across the display.“NO RT” is displayed if the current RDS station does not provide RTdata.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

3 Frequency display :

Displays the frequency of the current station.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

•VR6050/19-27/EN 4/9/02, 4:55 PM25

26 EN

(For the U.K. only)Presetting RDS stations (RDS AUTO MEMORY)

This function automatically stores up to 40 RDS stations in the presetmemory. In order to use the PTY function, the RDS stations must bestored in the preset memory using the RDS AUTO MEMORY function.

TUNER MULTI CONTROL

MEMORYBAND

1 Press the TUNER key to enter tuner mode.

2Use the BAND key to set the broadcast band to “FM”.

3 Press the MEMORY key continuously for more than 3seconds will start AUTO MEMORY.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

• After a few minutes, up to 40 RDS stations are preset in order fromchannel “01”.

• Stations already stored in the preset memory may be replaced byRDS stations. (i.e., If the RDS AUTO MEMORY function detects 15RDS stations, the stations currently preset at numbers 01~15 willbe replaced by the RDS stations.)

(For the U.K. only)Tuning by Program TYpe (PTY search)

This function lets you set the tuner to automatically search for stationswhich are currently broadcasting the type of program (genre) you wantto listen to.

Under certain receiving conditions, it may take more than 1

minute to complete the search.

Joystick(MULTI CONTROL5 /∞,DOWN2 / UP3)TUNING

1/¡

PTY

Preparations• Execute the RDS auto memory procedure.• Set the broadcast band to FM.• Tune to an RDS station.


1 Press the PTY key to activate the PTY search mode.Light up

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX PTY

When an RDS broadcast is received, the program type is shown onthe display. If no PTY data is available, or if the station is not an RDSstation, “NONE” is displayed.

2While the “PTY” indicator is lit, use the Joystick (5/∞) orTUNING 1 / ¡ keys select the program type of yourchoice.

Program type table

Program Type Name Display Program Type Name Display

Pop Music POP M Weather WEATHERRock Music ROCK M Finance FINANCEEasy Music EASY M Children’s Program CHILDRENLight Classical Music LIGHT M Social Affairs SOCIALSerious Classical Music CLASSICS Religion RELIGIONOther Music OTHER M Phone In PHONE INNews NEWS Travel TRAVELCurrent Affairs AFFAIRS Leisure LEISUREInformation INFO Jazz Music JAZZSport SPORT Country Music COUNTRYEducation EDUCATE National Music NATION MDrama DRAMA Oldies Music OLDIESCulture CULTURE Folk Music FOLK MScience SCIENCE Documentary DOCUMENTVaried Speech VARIED

“NO PROGRAM” is displayed if this operation is attempted

before performing the RDS Auto Memory operation.

3 Press the PTY key to start searching.

EXAMPLE : Searching for a Pop Music broadcast.

Display while searching. Blinks

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX PTY

Program type name display

Display when a station is received. Goes outRDS

L

SL S SB SR

C RSWLFE

DOLBY DIGITAL

PRO LOGIC




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RTY

MEMOSTEREOTUNED

Surround EX

Station name display

• No sound is heard while “PTY” is blinking.• If the desired program type cannot be found, “NO PROGRAM” is

displayed, then after several seconds the display returns to theoriginal display.

To select another program type.Repeat steps 1, 2 and 3.

•VR6050/19-27/EN 4/9/02, 4:55 PM26

27 EN

Ambience effects

This receiver is equipped with listening modes that allow

you to enjoy an enhanced sonic ambience with a variety of

video sources.

In order to obtain the optimum effect from the surround

modes, make sure to input the proper speaker settings

beforehand. *

Surround modes

Dolby DigitalThe Dolby Digital surround format lets you enjoy up to 5.1 channelsof digital surround sound from Dolby Digital program sources (such asLaserdisc or DVD software marked ). Compared with previ-ous Dolby surround, Dolby Digital provides even better sound quality,greater spatial accuracy, and improved dynamic range.

NoteAlthough a full set of speakers (front left, right, and center, surroundleft and right, and a subwoofer) is required for true 5.1 channel DolbyDigital surround sound, this receiver lets you enjoy Dolby Digital (andDolby Surround) program sources, even if you connect only the frontspeakers.

* LFE = Low Frequency Effects. This channel delivers separatenon-directional bass signals to the subwoofer for more dynamicdeep bass sound effects.Although only Dolby Digital soundtracks incorporate a separate lowfrequency channel, connecting a subwoofer will also improve deepbass performance in the other surround modes.The indication “LFE” appears in the display when a signal is beinginput for this channel.

“DTS” and “DTS Digital Surround” aretrademarks of Digital Theater Systems, Inc.

Manufactured under license from Dolby Laboratories. “Dolby”, “ProLogic” and the double-D symbol are trademarks of DolbyLaboratories.

“Circle Surround II and the ® symbol are trademarks of SRS Labs,

Inc. Circle Surround II technology is incorporated under license from SRSLabs, Inc”.

Dolby Digital EXDolby Digital EX is an extension of Dolby Digital technology, DolbyDigital EX creates six full-bandwidth output channels from 6.1-channelsources. This is done using a matrix decoder that derives threesurround channels from the two in the original recording.This is achieved by using three different surround signals, surround left,surround right, and surround back, each driving its own array ofspeakers. Think of it as adding a center channel for the rear speakers,which give more diffuse and natural surround effect, even if youwanted the ability to completely encircle the audience with sound,positioning sound effects exactly where they wolud be heard in real life.For best results, Dolby Digital EX should be used with movie soundtracksrecorded with Dolby Digital Surround EX which contain a digital flag thatwill automatically activate this feature. However, for titles releasedprior to late 2001, this feature has to be activated manually.

NoteAlthough a full set of speakers (front left, right, and center, surroundleft and right, surround back and a subwoofer) is required for true 6.1channel Dolby Digital Surround EX sound, this receiver lets you enjoyDolby Digital (and Dolby Surround) program sources, even if youconnect only the front speakers.

* LFE = Low Frequency Effects. This channel delivers separatenon-directional bass signals to the subwoofer for more dynamicdeep bass sound effects.Although only Dolby Digital soundtracks incorporate a separatelow frequency channel, connecting a subwoofer will also improvedeep bass performance in the other surround modes.The indication “LFE” appears in the display when a signal isbeing input for this channel.

Dolby PRO LOGIC IIDolby Pro Logic II was designed specifically to provide a new senseof spatiality, directionality and articulation of sounds from DolbySurround encoded sources (such as video and Laserdisc softwaremarked ). This is achieved with an intelligent, built-infeedback logic design, a matrix surround decoding and the decodingof stereo, full bandwidth surround outputs. The PRO LOGIC II modesprogrammed into this receiver are “MOVIE”, “MUSIC” and “PROLOGIC”. The “MOVIE” mode of the PRO LOGIC II has presetcharacteristics to produce a calibrated, high-level surround soundplayback while the “MUSIC” mode has user-adjustable characteris-tics to offer the three optional controls, like “Dimension”, “CenterWidth” and “Panorama” modes to allow optimization of the soundfieldsas desired. The “Dimension” control allows the user to graduallyadjust the soundfield either towards the front or towards the rear; the“Center Width” control allows various adjustment of the left-center-right speakers’ balance; the “Panaroma” extends the front stereoimage to include the surround speakers for an exciting “wraparound”effect with side wall imaging.

* Optional in this mode.

Surroundspeakers (L, R)

Center speaker

Subwoofer (SW)*

Front speakers (L, R)

Center speaker

Subwoofer (SW)




Center speaker

Subwoofer(SW)*




•VR6050/19-27/EN 4/9/02, 4:55 PM27

28 EN

Ambience effects

Multi channel surround sound (SRS Circle Surround II)SRS Circle Surround II™ improves on its predecessor CS-5.1™resulting in the CS-6.1™ system, enabling you to listen to realistic,multi-channel, surround sound playback from a stereo source orconventional surround-encoded video source. You already enjoylistening to Dolby Digital sound/DTS multi-channel sound with yourmulti-speakers. Now you can listen to audio CDs, MDs, Broadcast andHome Theater using your multi-speakers. You will discover a newtype of sound through SRS Circle Surround II.The CS system dramatically reduces storage space requirements formulti-channel content. It creates a listening environment that placesthe listener “inside” music performances, and dramatically improvesboth hi-fi audio and conventional surround-encoded video material.The CS decoder also includes the SRS technologies Focus™ andTruBass™. Focus electronically raises the sound stage from thespeaker location to an optimal position. TruBass creates deep, richbass in small speaker systems without the need for a subwoofer.

DVD 6-channel mode

Using a DVD player or the like equipped with six (5.1) output channelsand the receiver, you can enjoy multi-channel encoded DVD sourcematerial in all its splendor. Since the source signals are digital andeach channel is input independently, the resulting sound quality,sense of spaciousness, and dynamic range are superb.

* LFE = Low Frequency Effects. This channel delivers separate non-directional bass singnals to the subwoofer for more dynamic deepbass sound effects.

DSP modeThe DSP mode lets you add the atmosphere of a live concert or hallto almost any type of program source. These modes are particularlyeffective when used with stereo program sources, like CD, television,and FM radio. You might enjoy trying the ARENA, JAZZ CLUB,THEATER, STADIUM or DISCO mode the next time you watch aconcert or sporting event!

What's DSP?DSP stands for Digital Signal Processor.The way a sound is heard in an actual environment depends on avariety of different factors. One of the most important is reverberation(the act of decaying elements of sound echoing in various places).The DSP modes produce the feeling of presence by using the DSP tocreate reverberation, without spoiling the sound quality of the originalsignal.

DTSThe DTS multi-channel audio format is available on CD, LD and DVDsoftware. DTS is a strictly digital format and cannot be decoded insidemost CD, LD or DVD players. For this reason, if you attempt to listento DTS encoded software through the analog output of your new CD,LD or DVD player, you will experience digital noise in most cases. Thisnoise can be quite loud if the analog output is connected directly to ahigh power amplification system. Proper measures for playing thedigital output as described below should be taken to avoid thissituation. To enjoy DTS Digital Surround playback, an external 5.1channel DTS Digital Surround decoder system or an amplifier with abuilt-in DTS Digital Surround decoder must be connected to the digitaloutput (S/P DIF, AES/EBU or TosLink) of a CD, LD or DVD player.All models are incorporated with the DTS decoder.

* LFE = Low Frequency Effects. This channel delivers separate non-directional bass signals to the subwoofer for more dynamic deepbass sound effects.DTS has a .1 or LFE channel.The indication “LFE” appears in the display when a signal is beinginput for this channel.

Center speaker

Subwoofer(SW)




Center speaker

Subwoofer (SW)



Center speaker

Subwoofer (SW)*



Center speaker

Subwoofer (SW)*




•VR6050/28-34/EN 4/9/02, 4:56 PM28

29 EN

Surround playThe DTS compatible models can reproduce a CD, DVD, or LD carrying theDTS mark.DOLBY DIGITAL can be used when playing DVD or LD software bearingthe mark and DOLBY DIGITAL format digital broadcasts (etc.).DOLBY PRO LOGIC can be used when playing video, DVD, or LDsoftware bearing the mark.SRS Circle Surround II enables you to listen to multi channel sound fromthe stereo source.

INPUTSELECTOR

INPUT MODE

DSP INPUT MODE

LISTEN MODEInput Selector

DSP MODE

LISTEN MODE%/fi

Preparations• Turn ON related components.• Complete “Preparing for surround sound” (speaker settings). *• Use the Input Selector keys to select the component you wish to play

back with surround sound.• Use the INPUT MODE key to select the input mode (analog or digital)

for the source you wish to play back. 9• Noise will be produced when a DTS source is played by selecting the

analog input.

1 Start playing the video software.

2 Use the LISTEN MODE knob or LISTEN MODE %/fi keys toselect the listening mode.

The listening mode settings are stored separately for each input. Ifthe input mode is set to full auto (“AUTO DETECT” lights), thereceiver selects the optimal listening mode automatically based onthe type of input signal and the speaker settings.

Each turn of the LISTEN MODE knob or press of the LISTEN

MODE %/fi keys switches the setting as listed below.

The listening mode settings are different depending on the type

of input signal.

When the DOLBY DIGITAL or DOLBY DIGITAL EX signal isinput :(The DOLBY DIGITAL or PRO LOGIC, indicator lights up.)

1 DOLBY DIGITAL : DOLBY DIGITAL surround.2 DOLBY D EX : DOLBY DIGITAL EX surround.3 PLII MOVIE : PRO LOGIC II surround MOVIE mode.

(The PRO LOGIC indicator lights up.)4 PLII MUSIC : PRO LOGIC II surround MUSIC mode.

(The PRO LOGIC indicator lights up.)5 PRO LOGIC : PRO LOGIC II surround PRO LOGIC mode.

(The PRO LOGIC indicator lights up.)6 STEREO : Normal stereo playback.

Ambience effects

When you select DOLBY DIGITAL

“DOLBY DIGITAL” will be displayed.

SB

SW

DOLBY DIGITAL

PRO LOGIC L

SL SR

C R




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EX

LFE

When the DTS signal is input :(The DTS indicator lights up.)

1 DTS : DTS surround.2 STEREO : Normal stereo playback.

When the analog signal or the digital signal (except forDOLBY DIGITAL or DTS signal) is input :

1 PLII MOVIE : PRO LOGIC II surround MOVIE mode.(The PRO LOGIC indicator lights up.)

2 PLII MUSIC : PRO LOGIC II surround MUSIC mode.(The PRO LOGIC indicator lights up.)

3 PRO LOGIC : PRO LOGIC II surround PRO LOGIC mode.(The PRO LOGIC indicator lights up.)

4 CSII CINEMA : CS 6.1 surround.(The CS II indicator lights up.)

5 CSII MUSIC : CS 6.1 surround.(The CS II indicator lights up.)

6 CSII MONO : CS 6.1 surround.(The CS II indicator lights up.)

7 STEREO : Normal stereo playback.(The STEREO indicator lights up.)

• Dolby Digital or DTS signal having more channels than the maxi-mum number of playback channels available using the receiver’scurrent settings is input, downmixing is performed to match thenumber of available channels.

3DSP mode (Digital Signal Processor).

DSP can produce these effects without spoiling the sound quality ofthe original music or video source.

1 Pressing the DSP or DSP MODE key will display the current

DSP MODE status.

2 Each press of the key will switch to the next status as shown

bellow:

1 ARENA : DSP surround ARENA mode.2 JAZZ CLUB : DSP surround JAZZ CLUB mode.3 THEATER : DSP surround THEATER mode.4 STADIUM : DSP surround STADIUM mode.5 DISCO : DSP surround DISCO mode.

• The DSP mode selection is displayed for approximately 3seconds.

4Adjust the volume.

Notes• Depending on the type of the signal or speaker setting, some listening

modes cannot be selected.• When playback is started, the sound may be cut or interrupted before

the input source is confirmed as Dolby Digital.• To enjoy Dolby Digital surround (as well as all the other listening modes)

from a single component, be sure to use a Dolby Digital compatiblesource component.

•VR6050/28-34/EN 4/9/02, 4:56 PM29

30 EN

Ambience effects

DVD 6-channel playbackUsing a DVD player or the like equipped with six (5.1) output channels andthe receiver, you can enjoy surround sound playback.When you try to play a disc other than Dolby Digital such as DTS CD, nosound is produced or, noise may be heard. To avoid this situation, makesure that you connect the component to the receiver’s DVD/6CH INPUTjacks through a surround processor which can decode the surroundsignal you want to listen to.Connecting a DVD player which can decode the surround signal itself isalso acceptable.

INPUT MODE

DVD/6CH

INPUT MODE

VOLUME

DVD/6CH

VOLUME /

Preparations• Connect your DVD player to the DVD/6CH jacks of the receiver.• Turn on all other components that will be used.• Complete “Preparing for surround sound”. *

1 Press “DVD/6CH” as the input source.

• If speaker system B is on when “DVD/6CH” is selected as the inputsource, it switches off and speaker system A turns on automati-cally.

2 Select "6CH INPUT" by pressing the INPUT MODE key.

3 Start playback of the DVD software.

4Adjust the volume.

• It is not possible to adjust the volume level or sound quality (SET

UP, SOUND) of the channels separately when the receiver is in theDVD/6CH mode. Adjust the volume with the controls of the DVDplayer.For the powered subwoofer, you can adjust the volume of thesubwoofer using the subwoofer’s own volume control.

Convenient functions

MULTI CONTROLDIMMERSTEREO

SOUND LISTEN MODE

SOUND

LISTEN MODE%/fi

STEREO

Joystick(MULTI CONTROL5 /∞,DOWN2 / UP3)

DIMMER

Adjusting the soundYou can make further adjustments to the sound while listening toplayback in the surround mode.

1 Press the SOUND key and then use to the MMMMM/????? keys or Joystick

(2/3) until the desired item appears in the display.

Each time you press the MMMMM/????? keys or Joystick (2/3), the menu

changes as follows:

Note that some items are not displayed in certain modes.

1 CNTR (Center speaker level adjustment)*2 SR (Right surround speaker level adjustment)*3 SB (Surround back speaker level adjustment)*4 SL (Left surround speaker level adjustment)*5 SUBW (Subwoofer level adjustment)*6 INPUT (Input level adjustment - analog mode only) ¡7 MIDNIGHT (Midnight mode ON/OFF - Dolby Digital mode only)8 PANORAMA (Panorama mode ON/OFF)**9 DIMENSION (Dimension adjustment)**0 CENTER WIDTH (Center width adjustment)**- CENTER FOCUS (Center focus adjustment)***= CSII DLY (Rear speaker delay adjustment)***~ CSII GAIN (Input gain adjustment)***! TruBass (Trubass adjustment)***

* The adjustment is only temporary for the current input selection.The value will return automatically to the original setup valuewhen the power is turned on/off or when the input selection ischanged.

** Pro Logic II Music mode only.*** CS II mode only.


setting as desired.

• The adjustment item is displayed for approximately 8 seconds.

•VR6050/28-34/EN 4/9/02, 4:56 PM30

31 EN

Midnight mode (Dolby Digital mode only)When watching movies at night, you might not be able to raise thevolume as loud as normal. Midnight mode compresses the dynamicrange of previously specified parts of the Dolby Digital sound track (likescenes with sudden increases in volume) to minimize the difference involume between the specified and non-specified parts. This makes iteasy to hear all of the sound track, even when listening at low volumes.

1 Press the SOUND key, then press the MMMMM/????? keys or Joystick (2/3)

until “MIDNIGHT” appears on the display.

• This can be selected only if CD/DVD, DVD/6CH or VIDEO 2 is selectedas the source and the listen mode is set to “DOLBY DIGITAL”.

2 Use the MULTI CONTROL knob or Joystick (5/∞) to select the

ON or OFF setting.

PRO LOGIC L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXDOLBY DIGITAL

• The adjustment item is displayed for approximately 8 seconds.• Some Dolby Digital software may not be compatible with the

Midnight mode.

Panorama mode (Pro Logic II Music mode only)When listening to music, you will be able to enjoy the “wraparound”sound effect when you adjust the panorama mode.


until “PANORAMA” appears on the display.


PANORAMA ON or OFF.

1 PANORAMA ON : PANORAMA mode is ON.2 PANORAMA OFF : PANORAMA mode is OFF.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXPRO LOGIC

DOLBY DIGITAL

Dimension mode (Pro Logic II Music mode only)When listening to music with certain recordings, you will also be able toachieve a suitable balance from all the speakers by adjusting thedimension mode.


until “DIMENSION” appears on the display.


soundfield towards the rear or the front.

Soundfield is adjusted towards the front.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED


DOLBY DIGITAL

↓Soundfield is in neutral position.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED


DOLBY DIGITAL

↓Soundfield is adjusted towards the rear.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED


DOLBY DIGITAL

Center Width mode (Pro Logic II Music mode only)Center width adjustment allows you to enjoy an enchanced sound whenlistening to music through center image from only center speaker, or leftand right speakers or various combinations adjustments.


until “CENTER WIDTH” appears on the display.

• The CENTER WIDTH indication scrolls across the display.• When the center speaker is switched OFF, this mode will not be

effective.


left-center-right output.

Center image will be heard from center speaker only.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED


DOLBY DIGITAL

Center image will be heard from left and right speakers only.

L

SL S SB SR

C RSWLFE




DTS.MATRIX

DISCRETE

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED


DOLBY DIGITAL

• When in other position, center image from center speaker, left andright speakers can be heard simultaneously with variouscombinations.

Circle Surround II modeWhen you select the circle surround II mode, you will be able to enjoy themulti surround sound from the stereo source.

Use the LISTEN MODE knob or LISTEN MODE %/fi keys for CS IIselection.

Center Focus mode (CS II mode only)Center focus elevate level adjustment allows you to enjoy an enchancedsound when you select CS II CINEMA/MUSIC/MONO. It repositions thesound image to an optimal position more natural to the listener throughthe center image.


until “CENTER FOCUS” appears on the display.

L

SL SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE


center elevation level.

• The adjustment range is from 0 to 10.

L

SL SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

• CENTER FOCUS will not be available when the center speaker isOFF.

Ambience effects

•VR6050/28-34/EN 4/9/02, 4:57 PM31

32 EN

Ambience effects

CS II Rear Delay adjustment mode (CS II mode only)CS II Rear Delay adjustment provides a better sound effect from the rearspeakers.


until “CSII DLY” appears on the display.


rear speaker.

• The adjustment range is from 0 ms to 25 ms.

L

SL SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

CS II Gain adjustment mode (CS II mode only)CS II GAIN allows user to adjust the input gain for the Circle Surround IIprocessing.


until “CSII GAIN” appears on the display.


input gain.

• The adjustment range is from 0 to 18.

L

SL SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

TruBass adjustment mode (CS II mode only)TruBass adjustment provides deep, rich bass sound to various speakers.


until “TruBass” appears.

2 Use the MULTI CONTROL knob or Joystick (5/∞) to select the

following;

1 TruBass OFF

2 TruBass SW

3 TruBass LR

4 TruBass SW + LR

• After selecting 2, 3 or 4, TruBass speaker size and level adjustmentselection will be available.

3 For TruBass speaker selection, use the MULTI CONTROL knob

or Joystick (5/∞) to select any of the following display;

1 TruBass LARGE

2 TruBass MID

3 TruBass SMALL


TruBass Level.

• The adjustment range is from 0 (TruBass OFF) to 10.

L

SL SB SR

C R




DTS.MATRIX

DISCRETE

DOLBY DIGITAL

PRO LOGIC

STEREO

LOUDNESS

NEO:6


AUTO

RDSRTY

MEMOSTEREOTUNED

Surround EXSW

LFE

Display dimmer adjustmentThe dimmer function lets you select the brightness of the receiver'sdisplay. You might find this useful if you darken your room to watchmovies or listen to music.

Each time you press the DIMMER key, the display’s brightness

changes among the three available settings.

Select the brightness level you find most pleasing.

1 Bright

2 Medium

3 Dark

96kHz LPCM playbackThe receiver is compatible with the 96kHz LPCM playback. To play a96kHz DVD, set the listen mode to “STEREO”.

• In FULL AUTO input mode, the listen mode will automatically beSTEREO.

• When in DIGITAL MANUAL input mode (listen mode is not STEREO),“FS 96kHz” will appear in the display and no sound can be heard fromthe speakers.Press the LISTEN MODE or STEREO key (the listen mode changes tothe STEREO mode) to output sound from the speakers.

•VR6050/28-34/EN 4/10/02, 5:10 PM32

33 EN

The remote control supplied with this receiver is also capable

of controlling components from a variety of manufacturers

once you register the appropriate setup codes into the

remote control unit.

Low battery warningReplace all two batteries with new ones when you notice a shorteningof the distance from which the remote control will operate. In orderto retain the setup codes, please change the batteries approximatelywithin 30 seconds. If the setup codes are erased, please re-enter thecodes.

Registering setup codes for other components

SOURCE

Numeric keys

REMOTE MODE

INPUTSELECTOR

1 Find the setup code of the component to be registered.

• Refer to the setup code lists to find the setup code for thecomponent to be registered. fiflExample: To register a DVD made by KENWOOD, you would enter“805”.

Input Component Maker Code Key

(DVD) DVD player KENWOOD 805, 808 DVD

2Registering components for REMOTE MODE [(DVD, CBL,DSS/SAT, VCR, TV, OTHERS - RC-R0725/R0727) or (DVD, CD,CBL/SAT, VCR, TV, OTHERS - RC-R0726)] keys.

1 For DVD, CD, CBL, DSS/SAT, CBL/SAT, VCR or TV keys;

Hold down the SOURCE key and press the numeric keys to

enter the setup code.

• Example: Press “805” to register a DVD player manufactured byKENWOOD.

• If you push an invalid key, the remote control will exit the setupmode.

2 The OTHERS key enables you to operate another DVD, CD,

CBL, DSS/SAT, CBL/SAT, VCR or TV component.

For OTHERS key;

Hold down the OTHERS key and press the numeric keys to

enter the setup code.

• Example: After you have registered the KENWOOD DVD player,press “804” to register another DVD player which is manufacturedby Panasonic.

• If you push an invalid key, the remote control will exit the setupmode.

3Press any of the REMOTE MODE key and then press theSOURCE key to check that the component you want tocontrol turns on.

If the component does not react, and there is more than one

setup code, enter another setup code and try again.

• If the component is already on, pressing the SOURCE key willturn it off.

4Repeat steps 2 to 3 to register additional components untilall components have been registered.

Alternative REMOTE MODE key .This operation is optional and is convenient when you link an INPUTSELECTOR key to the REMOTE MODE key. While operating onecomponent, the INPUT SELECTOR key functions as an alternativeREMOTE MODE key to select another component.

• Example: REMOTE MODE (DVD) key can be linked to the INPUTSELECTOR (VIDEO 1) key as described below;

1 After registering the setup code, press and hold the SOURCE

key and then press the REMOTE MODE (DVD) key.

2 While holding down the SOURCE , press the INPUT

SELECTOR (VIDEO 1) key.

• Now the VIDEO 1 key will function as a DVD key which can beselected at the same time while operating a CD player.

• Repeat step 1 to 2 to link other INPUT SELECTOR keys.

NoteAlthough each setup code is designed to work with a number ofdifferent models, certain codes may not work with some models.(Also, certain codes may only operate some of the functions availableon a given model.)

Basic remote control operations for other components

•VR6050/28-34/EN 4/17/02, 6:25 PM33

34 EN

Operating other componentsThis operation lets you operate the registered components.KENWOOD audio components with system control turn on and offautomatically with the receiver via the system control connections.

SOURCERECEIVER

INPUTSELECTOR

1Use the INPUT SELECTOR keys to select the component youdesire.

• Pressing the INPUT SELECTOR keys also changes the input selectoron the receiver.

• When you operate your registered DVD player, Cable tuner,

DSS/SAT receiver, VCR or TV, go to step 2.

• When you operate the CD player, Cassette deck, MD player, or

Tuner with system control connection, go to step 3.

2Press the SOURCE key.

• To return to the receiver operation mode, press the RECEIVER key.

3Press the operation keys you desire. °

The remote control mode remains at the selected input. If you

wish to operate another component, repeat step 2 or 3.

NoteBe sure to point the remote control at the remote sensor on thereceiver when you want to operate KENWOOD components connectedby system control cords. Otherwise, point the remote control at thecomponent you want to operate.


•VR6050/28-34/EN 4/4/02, 10:04 PM34

35 EN

Setup code chart (RC-R0727) (VR-6050/KRF-V6060D)/(RC-R0725)(KRF-V7060D)


TV Setup codes

Maker Setup codes

AKAI 125BELL+HOWELL 142CENTURION 126CORONAD 127DAEWOO 136, 140, 141, 145EMERSON 130, 131, 132, 133, 146FISHER 119G.E. 102, 122, 129GOLD STAR 137, 148HITACHI 114, 115JVC 113KTV 138, 139LOEWE 123, 124MAGNAVOX 109, 147MARANTZ 121MITSUBISHI 121PANASONIC 111, 112, 122, 129PHILIPS 109, 147PIONEER 116PROSCAN 117RADIOSHACK 128RCA 102, 103, 104, 105, 106, 126SAMSUNG 134, 135SANYO 119SEARS 120SHARP 110SONY 101SYMPHONIC 143, 144TOSHIBA 120QUASAR 111, 118ZENITH 107, 108

Maker Setup codes

HITACHI 812JVC 801KENWOOD 805, 808MITSUBISHI 810ONKYO 815, 816PANASONIC 804PHILIPS 807PIONEER 803PROSCAN 811RCA 811SAMSUNG 814SONY 802TOSHIBA 806YAMAHA 809ZENITH 806, 813

DVD player Setup codes

Maker Setup codes

GEMINI 218G.I. 209HAMLIN 210, 211, 234, 235JERROLD 201, 202, 224, 225, 226, 227,

228, 229, 233MACOM 215, 216, 217MAGNAVOX 236OAK 212, 213, 214PANASONIC 221, 222, 232PHILIPS 219, 220, 237, 238, 239, 240PIONEER 206, 207SAMSUNG 223S. ATLANTA 203, 230, 231TOCOM 208ZENITH 204, 205

CBL codes

DSS/SAT codes

Maker Setup codes

ECHOSTAR 903G.I. 902HITACHI 908HUGHES 906PANASONIC 905PRIMESTAR 909RCA 901SONY 907TOSHIBA 904

Maker Setup codes

AIWA 352AKAI 354, 355, 356BELL+HOWELL 351DAEWOO 349EMERSON 334, 335, 336, 337, 338FISHER 330, 341, 342, 343G.E. 307, 321GOLD STAR 323GO_VIDEO 347, 348, 353HITACHI 307, 308, 328, 329JVC 324, 325, 326, 327MAGNAVOX 311, 312, 313MITSUBISHI 315, 316, 317, 318, 357, 358NEC 344, 345ORION 335PANASONIC 309, 310PHILIPS 313QUASAR 309, 310, 311, 312RCA 308SAMSUNG 332, 339, 340SANYO 351SCOTT 331SHARP 319, 320SHINTOM 333SONY 301, 302, 303, 304, 305, 306SYNPHO 346TEKNICA 346, 350TOSHIBA 314ZENITH 322

VCR Setup codes

•VR6050/35-44/EN 4/9/02, 4:57 PM35

36 EN


Setup code chart (RC-R0726) (KRF-V6060D) (For the U.K. only)

DVD player Setup codes

Maker Setup codes

JVC 801KENWOOD 805, 808PANASONIC 804PHILIPS 807PIONEER 803SONY 802TOSHIBA 806

TV Setup codes

Maker Setup codes

AKAI 408BLAUPUNKT 401FENNER 412FISHER 413GRUNDIG 402HITACHI 414, 415INNO-HIT 416IRRADIO 408JVC 417LOEWE 429, 430MAGNAVOX 406MIVER 401NOKIA 403NORDMENDE 404, 405OKANO 416ORION 418PANASONIC 419, 420PHILIPS 406SABA 404, 407SAMSUNG 421SANYO 413SCHNEIDER 408SHARP 422SONY 423, 424, 425, 426, 427TELEFUNKEN 407, 409, 410THOMSON 411TOSHIBA 428

Maker Setup codes

AIWA 513BELL+HOWELL 514BLAUPUNKT 501CGM 514, 515DIGTAL 515FISHER 514G.E. 516GRUNDIG 502HITACHI 517, 518JVC 519LOEWE 503, 504MAGNAVOX 501, 515MITSUBISHI 520, 521, 522, 523NOKIA 505NORDMENDE 506, 507, 508PANASONIC 524PHILIPS 509PHONOLA 515SABA 510SAMSUNG 525, 526SANYO 514SHARP 527, 528SIEMENS 502SONY 529, 530, 531TELEFUNKEN 511, 512TOSHIBA 532

VCR Setup codes

Maker Setup codes

AMSTRAD 601, 602, 603, 604, 633CANAL+ 622D-BOX 626ECHOSTAR 619, 620, 621, 623FORCE 630GALAXIS 629GRUNDIG 605, 606HIRSCHMANN 639ITT 609JERROLD 616JVC 614JVC/BT 613KATHREIN 611, 612, 636MASCOM 634NOKIA 628, 635PACE 608, 627PANASONIC 615PHILIPS 607, 625SELECTOR 631SKYMASTER 610, 638THOMSON 637TPS/SAGEM 624TRIAX 632VIDEOWAY 617, 618

CBL/SAT codes

CD player Setup codes

Maker Setup codes

DENON 702ONKYO 704PHILIPS 705PIONEER 706SONY 701TEAC 703YAMAHA 707

•VR6050/35-44/EN 4/9/02, 4:57 PM36

37 EN

CASSETTE deck, CD player & MD recorder operationsYou can perform these basic operations using the keys described below when connected to KENWOOD cassette deck, CD player or MD recorderequipped with system control operations. &

Cassette deck operations keys CD player operation keys

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

A/B(Cassette deck

selection)

3/8 (3 Play)2 (Reverse play)

1 (Rewind)¡ (Fast Forward)

7 (Stop)

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)

(For RC-R0726 and RC-R0725 only)

PHONO

CD CBL/SAT

(For RC-R0726 only)

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

3/8 (Play/Pause) 1 (Backward Search)¡ (Forward Search)

3 (Skip up)2 (Skip down)

7 (Stop)

Numeric keys(Select tracks)

DISC SKIP

DISC SEL(Disc selection)


PHONO

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)

CD

(For RC-R0726 only)

CBL/SAT

MD recorder operation keys

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

3/8 (Play)

7 (Stop)

+100(Select tracks)

1 (Backward Search)¡ (Forward Search)


CD CBL/SAT

(For RC-R0726 only)

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)


PHONO

3 (Skip up)2 (Skip down)


•VR6050/35-44/EN 4/9/02, 4:58 PM37

38 EN


Other components’ operationsRefer to the following for the type of remote control operations available for each component.

• When pressing keys in succession, press each key firmly and be sureto wait at least 1 second before pressing the next key.

• Numeric keys function the same as the numeric keys on the originalremote.

These keys can be used to perform the basic operations of KENWOOD and other manufacturers’ components which the setup code for each

component had been entered beforehand. fifl

TV operation keys VCR operation keys

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

(Power on/off)

Numeric keys

VOL + / – (Volume + / –)

CH + / – (Channel + / –)

MUTE

INPUT SEL(Input selection)

ENTER


PHONO

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)

CD CBL/SAT

(For RC-R0726 only)

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

INPUT SEL(Input selection)

Numeric keys

CH + / – (Channel + / –)

3/8 (3 Play)

8 (Pause)

1 (Rewind)¡ (Fast Forward)


PHONO

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)

SOURCE(Source power)

7 (Stop)

CD CBL/SAT

(For RC-R0726 only)

1 Select the input source.

2 Press the keys corresponding to the operations you desire.

Refer to the following sections for details.

•VR6050/35-44/EN 4/9/02, 4:58 PM38

39 EN


DSS/SAT (or CBL/SAT) receiver operation keys Cable tuner operation keys

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

CH + / – (Channel + / –)

ENTER

MENU5 (Cursor up)∞ (Cursor down)2 (Cursor left)3 (Cursor right)

Numeric keys



PHONO

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)

CD CBL/SAT

(For RC-R0726 only)

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

CH + / – (Channel + / –)

ENTER


Numeric keys

CD CBL/SAT

(For RC-R0726 only)

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)


PHONO

DVD player operation keys

P.CALL 4 /DOWN

P.CALL/UP ¢

TUNING

+

TOP MENUSET UP

MENUSOUND

TV CONTROL

VOL.

VOLUME

+

- - INPUT SEL

+

-CH

DVD

VCR

CBL

TV

DSS/SAT

OTHERS

RECEIVER

SOURCE POWER

ACTIVE EQ

OSD RETURN

DISC SEL DISC SKIP

FLIP BAND





MUTE

DVD

ENTER

INPUT SELECTOR

MULTICONTROL

¢

4

1 ¡ 2 6

7 DIMMER

™ £

™

1

4

7

+10

2

5

8

0

3

6

9

+100

REMOTE MODE

LISTEN MODE


SPEAKER EQ

™

VIDEO 3

AV AUX

PAGE

TOP MENU(Title)

PAGE %/fi(Page up or down)

MENU

RETURNOSD

2 (Flip)3/8 (3 Play)

8 (Pause)

7 (Stop)

1 (Backward Search)¡ (Forward Search)

¢ (Skip up)4 (Skip down)




PHONO

ENTER

PAGE DOWNPTY

PAGE UPRDS DISP

(For RC-R0726 only)

5 (Cursor up)∞ (Cursor down)2 (Cursor left)3 (Cursor right)

CD CBL/SAT

(For RC-R0726 only)

•VR6050/35-44/EN 4/9/02, 4:58 PM39

40 EN

In case of difficulty

Tuner

Cause

• No antenna is connected.• The broadcast band is not set properly.• The frequency of the desired station is not

tuned.

• Noise due to ignition noise from an automo-bile.

• Noise due to interference from an electricappliance.

• Noise due to a nearby TV set.

• The preset station belongs to a frequency thatcannot be received.

• The preset memory was cleared because thepower cord had been unplugged for a longperiod of time.

Remedy

• Connect an antenna. ^• Set the broadcast band properly.• Tune the frequency of the desired station.

¢

• Install the outdoor antenna away from theroad.

• Turn off the power to the appliance.

• Install the receiver farther away from the TV.

• Preset a station with a receivable frequency.

• Preset the station again.

Symptom

Radio stations cannot be received.

Interference.

A station which was preset cannot be re-

ceived by pressing the corresponding nu-

meric key.

Amplifier

Cause

• The speaker cords are disconnected.

• VOLUME is set to the minimum position.• MUTE is ON.• The SPEAKERS switches are set to OFF.

• Speaker cords are short-circuited.

• The speaker cord is disconnected.

• The surround speaker cords and/or the centerspeaker cord is disconnected.

• A surround mode has not been engaged.• The surround and/or center volume controls

are set to the minimum level.

• The audio cord from the record player is notconnected to the PHONO jacks.

• The record player is not grounded.

• There are many possible causes for this prob-lem, depending on the type of DVD playerused.

• The input mode is set to digital manual.

• The software is copy-guarded.

Remedy

• Connect them properly referring to “Connect-ing the speakers” $

• Adjust the volume to a proper level.• Turn OFF the MUTE. ™• Set the SPEAKERS switches to ON. ¡

• Turn the power off, eliminate the short-circuit-ing, then turn on the power again.

• Connect it properly referring to “Connectingthe speakers”. $

• Connect it properly referring to “Connectingthe speakers”. $

• Select a surround mode.• Adjust the speaker levels using the test tone.

(

• Insert the audio cord plugs securely into thePHONO jacks.

• Connect the grounding wire to the GND termi-nal on the rear panel.

• Set the input mode to digital manual beforestarting playback of the Dolby Digital source.

9

• Press the INPUT MODE key to select to fullauto mode. 9

• Copy-guarded video software cannot be re-corded.

Symptom

No sound from the speakers.

The standby indicator blinks and sound is

not output.

Sound is not output from one of the speakers.

Sound is not output from the surround

speakers and / or the center speaker, or their

sound is very small.

A humming noise is generated when the

PHONO input selector is selected.

When playing a Dolby Digital source signal

using a DVD player, the sound is cut off soon

after it starts.

No sound is produced during playback from

a DVD player.

A video source cannot be recordednormally.

Resetting the MicrocomputerThe microcomputer may malfunction (unit cannot be operated, or

shows an erroneous display) if the power cord is unplugged while

the power is ON, or due to some other external factor. If this

happens, execute the following procedure to reset the microcom-

puter and return the unit to its normal operating condition.

• Please note that resetting the microcomputer will clear the contentsof the memory and returns the unit to the state it was in when it leftthe factory.

For the U.S.A. and CanadaUnplug the power cord from the wall outlet, then plug it

back in while holding down the POWER ON/STANDBY

key.

For other countriesWith the power cord plugged in, turn the POWER ON/

OFF key OFF. Then, while holding down the ON/

STANDBY key, press POWER ON/OFF.

•VR6050/35-44/EN 4/9/02, 4:58 PM40

41 EN

Remote control unit

Cause

• No setup codes registered for the respectiveinput(s).

• The remote control is set to a different opera-tion mode.

• Batteries are exhausted.• The remote control unit is too far away from

the main system, controlling angle is too large,or there is an obstacle between the receiverand the remote.

• The audio cords and system control cords arenot connected properly.

• No software is loaded in the source component.

• An attempt is made to play a tape which isbeing recorded in the cassette deck.

• The remote control has not been set to theoperation mode for the component you wishto control.

Remedy

• Register a setup code at the respective input(s).fifl

• Press the source select keys or SOURCE

keys to select the appropriate operation mode.• Replace with new batteries.• Operate the remote control unit within the

controllable range.

• Connect properly referring to “Setting up thesystem”.

• Place software in the source component youwant to play.

• Wait until recording has completed.

• Press the source select keys or SOURCE

key to activate the operation mode for thecomponent you want to control beforeoperation. ›

Symptom

Certain inputs cannot be selected using the

remote control.

Remote control operation is not possible.

In case of difficulty

•VR6050/35-44/EN 4/9/02, 4:58 PM41

42 EN

Specifications

For the U.S.A and Canada

AUDIO section (VR-6050)Rated power output during STEREO operation

Effective power output during SURROUND operation

FRONT (20 ~ 20 kHz, 0.09 % T.H.D. at 8 Ω one channel driven)............................................................................... 100 W + 100 W

CENTER (20 ~ 20 kHz, 0.09 % T.H.D. at 8 Ω one channeldriven) .................................................................................. 100 WSURROUND (20 ~ 20 kHz, 0.7 % T.H.D. at 8 Ω one channeldriven) ................................................................... 100 W + 100 W

Total harmonic distortion ....................... 0.009 % (1 kHz, 50 W, 8 Ω)Frequency response

Line (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)................................................. 10 Hz ~ 100 kHz, +0 dB ~ –3.0 dB

Signal to noise ratio (IHF’66)Line (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)............................................................................................... 95 dB

Loudness controlVOLUME at –30 dB level ...................................... +6 dB (100 Hz)

Input sensitivity / impedanceLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH).............................................................................. 500 mV / 47 kΩ

Output level / impedanceTAPE REC ............................................................... 500 mV / 1 kΩPRE OUT (SURROUND BACK CHANNEL) .............. 2.5 V / 1 kΩPRE OUT (SUBWOOFER) ......................................... 2.5 V / 1 kΩ

Tone controlBASS................................................................ ±10 dB (at 100 Hz)TREBLE ............................................................ ±10 dB (at 10 kHz)

For other countries (except for the U.K.)

AUDIO section (KRF-V7060D/V6060D)Effective power output during STEREO operation

1 kHz, 10 %, 8 Ω ......................................................... 110 W + 110 WRated power output during STEREO operation

Effective power output during SURROUND operationFRONT (1 kHz, 10 % T.H.D. at 8 Ω one channel driven)............................................................................... 110 W + 110 W

CENTER (1kHz, 10 % T.H.D. at 8 Ω one channel driven).............................................................................................. 110 W

SURROUND (1 kHz, 10 % T.H.D. at 8 Ω one channel driven)............................................................................... 110 W + 110 W

Total harmonic distortion ........................ 0.009% (1 kHz, 50 W, 8 Ω)Frequency response


PHONO ‘RIAA’ response (KRF-V7060D).................................................. 40 Hz ~ 20 kHz, 1.5 dB ~ –3.0 dB

Maximum input levelPHONO (MM) (KRF-V7060D) ........... 45 mV, 1 % T.H.D. at 1 kHz

Signal to noise ratio (IHF’66)PHONO (MM) (KRF-V7060D) ............................................... 75 dBLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)............................................................................................... 95 dB


Input sensitivity / impedancePHONO (MM) (KRF-V7060D) ............................... 6.0 mV / 47 kΩLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH).............................................................................. 500 mV / 47 kΩ

Output level / impedanceTAPE REC ............................................................... 500 mV / 1 kΩPRE OUT (SURROUND BACK CHANNEL) ............... 2.5 V / 1 kΩPRE OUT (SUBWOOFER) .......................................... 2.5 V / 1 kΩ

Tone controlBASS............................................................... ±10 dB (at 100 Hz)TREBLE ........................................................... ±10 dB (at 10 kHz)

DIGITAL AUDIO sectionSampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHzInput level / impedance / wave length

Optical ........................... (–15 dBm ~ –24 dBm), 660 nm ±30 nmCoaxial ................................................................... 0.5 Vp-p / 75 Ω

VIDEO sectionVIDEO inputs / outputs

VIDEO (composite) ................................................. 1 Vp-p / 75 ΩS VIDEO inputs /outputs

S VIDEO (luminance signal) ................................... 1 Vp-p / 75 ΩS VIDEO (chrominance signal) ....................... 0.286 Vp-p / 75 Ω

FM tuner sectionTuning frequency range................................. 87.5 MHz ~ 108.0 MHzUsable sensitivity (MONO)

VR-6050................... 1.3 µV (75 Ω)/ 13.2 dBf (75 kHz dev, SINAD 30 dB)

KRF-V7060D/V6060D ........................................................................................ 1.6 µV (75 Ω)/ 15.2 dBf (75 kHz dev, SINAD 30 dB)

50 dB quieting sensitivitySTEREO ..................................................... 28 µV (75 Ω)/ 40.2 dBf

Total harmonic distortionMONO (1 kHz, 75 kHz dev) .......................... 0.5% (65 dBf input)STEREO (1 kHz, 67.5 + 6.75 kHz dev) ......... 0.7% (65 dBf input)

Signal to noise ratioMONO (1 kHz, 75 kHz dev) ........................ 75 dB (65 dBf input)STEREO (1 kHz, 67.5 + 6.75 kHz dev) ....... 68 dB (65 dBf input)

Stereo separation (1 kHz) ........................................................... 40 dBSelectivity (±400 kHz) (VR-6050) ............................................... 70 dB (KRF-V7060D/V6060D) .......................... 50 dBFrequency response (30 Hz ~ 15kHz) ..................... +0.5 dB, –3.0 dB

AM tuner sectionTuning frequency range

10 kHz step ................................ 530 kHz ~ 1,700 kHz (VR-6050)10 kHz step .......... 530 kHz ~ 1,610 kHz (KRF-V7060D/V6060D)9 kHz step ............ 531 kHz ~ 1,602 kHz (KRF-V7060D/V6060D)

Usable sensitivity (30% mod, S/N 20 dB)........................................................................ 16 µV / (600 µV/m)

Signal to noise ratio (30% mod, 400 Hz).......................................................... 50 dB (60 dBµ VEMF input)

GENERALPower consumption VR-6050 ....................................................... 3 A

KRF-V7060D/V6060D ............................ 300 WAC outlet

SWITCHED VR-6050 ..................... (total 150 W, 1.25 A max.)KRF-V7060D/V6060D .............. (total 90 W max.)

Dimensions ..................................................... W : 440 mm (17-5/16")H : 159 mm (6-1/4")D : 392 mm (15-7/16")

Weight (Net)VR-6050 ................................................................ 9.4 kg (20.7 lb)KRF-V7060D/V6060D ......................................... 10.0 kg (22.0 lb)

Caution : Read this page carefully to ensure safeoperation.

100 watts per channel minimum RMS, both channels driven,at 8 Ω from 20 Hz to 20 kHz with no more than 0.09% totalharmonic distortion. (FTC)

100 watts per channel minimum RMS, both channels driven,at 8 Ω from 20 Hz to 20 kHz with no more than 0.09% totalharmonic distortion. (FTC)

•VR6050/35-44/EN 4/9/02, 4:58 PM42

43 EN

Notes1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).

Specifications

For the U.K. only

AUDIO section (KRF-V6060D)Rated power output during STEREO operation

DIN/IEC (63 Hz ~ 12.5 kHz, 0.09 % T.H.D. at 6 )............................................................................... 100 W + 100 W

Effective power output during SURROUND operation

FRONT (63 Hz ~ 12.5 kHz, 0.09 % T.H.D. at 6 Ω one channeldriven) ................................................................... 100 W + 100 WCENTER (63 Hz ~ 12.5 kHz, 0.09 % T.H.D. at 6 Ω one channeldriven) ..................................................................................... 100 WSURROUND (63 Hz ~ 12.5 kHz, 0.7 % T.H.D. at 6 Ω one channeldriven) ............................................................................ 100 W + 100 W

Total harmonic distortion ....................... 0.009 % (1 kHz, 50 W, 6 Ω)Frequency response


PHONO ‘RIAA’ response .............. 40 Hz ~ 20 kHz, +1.5 dB ~ –3.0 dBMaximum input level

PHONO (MM) .................................... 45 mV, 1 % T.H.D. at 1 kHzSignal to noise ratio (IHF’66)

PHONO (MM) ........................................................................ 75 dBLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH)............................................................................................... 95 dB


Input sensitivity / impedancePHONO (MM) ........................................................ 6.0 mV / 47 kΩLine (CD/DVD, TAPE, VIDEO 1, VIDEO 2, VIDEO 3, DVD/6CH).............................................................................. 500 mV / 47 kΩ

Output level / impedanceTAPE REC ............................................................... 500 mV / 1 kΩPRE OUT (SURROUND BACK CHANNEL) .............. 2.5 V / 1 kΩPRE OUT (SUBWOOFER) ......................................... 2.5 V / 1 kΩ

Tone controlBASS................................................................ ±10 dB (at 100 Hz)TREBLE ............................................................ ±10 dB (at 10 kHz)

DIGITAL AUDIO sectionSampling frequency ...................... 32 kHz, 44.1 kHz, 48 kHz, 96 kHzInput level / impedance / wave length

Optical ........................... (–15 dBm ~ –24 dBm), 660 nm ±30 nmCoaxial ................................................................... 0.5 Vp-p / 75 Ω

VIDEO sectionVIDEO inputs / outputs

VIDEO (composite) ................................................. 1 Vp-p / 75 ΩS VIDEO inputs /outputs

S VIDEO (luminance signal) ................................... 1 Vp-p / 75 ΩS VIDEO (chrominance signal) ....................... 0.286 Vp-p / 75 Ω

FM tuner sectionTuning frequency range.....................................87.5 MHz ~ 108 MHzUsable sensitivity

MONO............ 1.3 µV (75 Ω)/ 13.2 dBf (40 kHz dev, S/N 26 dB)STEREO .... 45 µV (75 Ω)/ 42.1 dBf (40 + 6 kHz dev, S/N 46 dB)

Total harmonic distortionMONO (1 kHz, 40 kHz dev) ....................... 0.2% (65.2 dBf input)STEREO (1 kHz, 40 + 6 kHz dev) ............... 0.8% (65.2 dBf input)

Signal to noise ratio (DIN weighted at 1 kHz)MONO........................................................ 65 dB (65.2 dBf input)STEREO ..................................................... 60 dB (65.2 dBf input)

Stereo separation (1 kHz) ........................................................... 36 dBSelectivity (±300 kHz) ................................................................. 64 dBFrequency response (30 Hz ~ 15kHz) ..................... +0.5 dB, –3.0 dB

MW tuner sectionTuning frequency range..................................... 531 kHz ~ 1,602 kHzUsable sensitivity (30% mod, S/N 20 dB) ......... 16 µV / (600 µV/m)Signal to noise ratio (400 Hz, 30% mod)

.......................................................... 50 dB (60 dBµ VEMF input)

GENERALPower consumption ................................................................. 330 WAC outlet

SWITCHED ...................................................... (total 90 W max.)Dimensions ..................................................... W : 440 mm (17-5/16")

H : 159 mm (6-1/4")D : 392 mm (15-7/16")

Weight (Net) ................................................................ 9.8 kg (21.6 lb)

•VR6050/35-44/EN 4/9/02, 4:58 PM43

44 EN

For your recordsRecord the serial number, found on the back of the unit, in the spacesdesignated on the warranty card, and in the space provided below. Referto the model and serial numbers whenever you call upon your dealer forinformation or service on this product.

Model__________________ Serial Number ________________________

•VR6050/35-44/EN 4/9/02, 4:58 PM44

VR-6050 KRF-V7060D KRF-V6060D - KENWOODmanual.kenwood.com/files/B60-5192-10.pdf · 2010-09-17 ·...

Documents

Transcript of VR-6050 KRF-V7060D KRF-V6060D - KENWOODmanual.kenwood.com/files/B60-5192-10.pdf · 2010-09-17 ·...