VIKIS DIGITAL ALARM CLOCKMANUAL

Novita WidjajaROBT 1A 2012December 6, 2012

VIKIS DIGITAL ALARM CLOCKMANUAL

Novita WidjajaDecember 6, 2012

TABLE OF CONTENTS

1. Introduction12. Parts23. Operation33-1 Initial Settings3-2 Regular Settings4. Troubleshooting45. Specification

LIST OF FIGURES

Figure 2-1Vikis Digital Alarm ClockFigure 3-1Backside ConfigurationFigure 3-2Front Display

Introduction

A digital alarm clock is a device used not only to show the time but also have an alarm function. Some people like digital clock more than the manual one for some reasons such as precision, convenience and modern appearance. It shows the exact minute compare to the manual alarm clock which sometimes requires more attention for the user to be able to see the small lines between 5-minute intervals.A special digital alarm clock has a light that can be turned on while needed. It also has removable frame so that it can be put in various positions.VIKIS Digital Alarm Clock is a user friendly alarm clock. It has modern appearance but very simple to operate. It is very useful for anyone never had experience with digital clock to read over these instructions before starting using the clock and keep it as future reference in case any changes in settings need to be made.This manual describes the functions of the three main parts and then the operation of this digital alarm clock.

1-1

Parts

A digital alarm clock has three major parts (see Figure):1.Cover panel2.LCD (Liquid Crystal Display) display panel3.Back side panel

Figure 2-1: VIKIS Digital Alarm Clock

2-1The function of the removable cover panel is to pose the alarm clock in various positions depend on the users preferences. It has three possibilities which are:1.Thin flat rectangle surface on top of the body, hang over desk or shelf rim.2.Thin flat rectangle surface on top of the body, put on any surface will create 50` angle which for some position will be an advantage.3.Thin flat rectangle surface under the body, put on any surface the digital display will be perpendicular to the surface.

The LCD display shows the time and alarm set. It also shows symbols that represent the setting has been made such as 24-hour or AM/PM and alarm on or alarm off. When the light button turned on, the LCD display will have blue light in the background that enable the user to see the time in the dark.

The back panel has three buttons which are MODE, SET and LIGHT button. It also has battery compartment to supply the power required.

2-2Operation

Two AAA batteries are required for this digital alarm clock. It requires the user to set the clock first before setting the alarm. When the alarm is set, it will go off on the exact time set for every day. When the alarm signal is on and mode button is pressed, the alarm snoozed or the set button pressed will turn the alarm off. Whenever it is too dark to see the display, the light can be turned on by simply press the body of the alarm against the wall behind because the light button is positioned in such a way that it does not require user to press in the exact position.

Tools and Materials-Small (+) screwdriver preferably less than 5mm in diameter-2 (two) LR03 AAA size 1.5V Battery

Installing the Battery1.Use the screwdriver to open the battery compartment on the back side of the alarm clock (see figure 1)2.Insert the two LR03 AAA size 1.5V battery required the opposite way one to another (look at the + and sign shown in the battery compartment)3.Screw the cover back in place3-1

Initial SettingsNote: Time setting is required before any alarm setting can be made.1.Date and Time SettingPress the SET button until it the first two digits are blinking. Press the MODE button several times until the last two digits show the date desired, then press SET. The last two digits will start blinking. Press MODE button several times until the desired month is shown. Press SET to finalize the date setting.Press MODE to go to the time setting. Press SET button until the first two digits are blinking. Press MODE button until the first two digits show the hour, then press SET. The last two digits that show the minute will start blinking. Press MODE button to select the minute and SET button to finalize the time setting.2.12 Hour/24 Hour SettingPress MODE button to select the 12 hour/24 hour setting. Press the SET to select and finalize the choice.

Regular Setting1.Alarm SettingPress MODE button until the bell symbol appear on the left corner of the display. Press SET button to go to setting mode and the digits start blinking. Press the MODE button to select the alarm time and press SET to finalize the alarm setting.3-3The alarm symbol appears on the display means that the alarm is active and it will go off at the time set every day. To deactivate the alarm, go to the alarm mode and press the SET button until it disappear from the display (see figure 2)2.Chime SettingGo to the chime setting by pressing the MODE button until the bell symbol appears on the upper left corner of the display. It means the chime will sound every hour. Then press SET. To deactivate it, press SET after it disappears. Light/Snooze ButtonPress the light button to turn the display light on. Pressing this button when the alarm goes off will snooze (pause) the alarm for 5 minutes.

3-4

Figure 3-2: Front DisplayFigure 3-1: Backside Configuration

3-4Troubleshooting

The clock does not display anything when turned onCheck the battery power

MODE, SET or LIGHT buttons do not respondCheck the battery position

CONTACTING IKEA:http://www.ikea.comCall us: 1-866-866-IKEA (4532)4-1