Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf
-
Upload
nitin-prajapati -
Category
Documents
-
view
21 -
download
0
Transcript of Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf
![Page 1: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/1.jpg)
FM Transmitter
• FM Broadcast Range 88 to 108 MHz.
• Channel Separation 200 KHz
• Frequency Deviation ∆ = 75 KHz • Frequency Deviation ∆ = 75 KHz
• FM Broadcast
� Monophonic
� Stereophonic ( Left and Right Channel)
![Page 2: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/2.jpg)
FM Stereo Transmitter
• Signals L + R and L – R are Pre-Emphasized.
• Input Audio Signal (L-R)’ is Converted to NBFM by DSBSC
Modulator. Uses Armstrong Method of FM Generation
• Carrier Used for this Modulation is 38 KHz.
• This carrier is Obtained from Pilot Source of 19 KHz via
Frequency Doubler.
• Signal (L+ R)’ is used Directly
![Page 3: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/3.jpg)
FM Transmitter
Composite Baseband Signal for Final Wideband FM
Modulation is
Pilot is Kept at 19 KHz as on its both side there is no signals up to 4 KHz.
![Page 4: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/4.jpg)
FM receiver• FM receiver is similar to the
superheterodyne layout
• Only Difference is Envelope Detector is replaced by Limiter – Discriminator and De-Emphasis Circuits
• RF is 88 to 108 MHz, IF is 10 MHz.
RF
mixer
LO
limiterDiscrimi-
natordeemphasis
AF power
amp
IF
![Page 5: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/5.jpg)
Receiver components:
RF amplifier
• AM may skip RF amp but FM requires it
• FM receivers are called upon to work with
weak signals (~1µV or less as compared to 30
µ
weak signals (~1 V or less as compared to 30
µV for AM)
• An RF section is needed to bring up the signal
to at least 10 to 20 µV before mixing
![Page 6: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/6.jpg)
Limiter
• A limiter is a circuit whose output is constant
for all input amplitudes above a threshold
• Limiter’s function in an FM receiver is to
remove unwanted amplitude variations of the remove unwanted amplitude variations of the
FM signal
Limiter
![Page 7: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/7.jpg)
Limiting and sensitivity
• A limiter needs about 1V of signal, called
quieting or threshold voltage, to begin
limiting
• When enough signal arrives at the receiver to • When enough signal arrives at the receiver to
start limiting action, the set quiets, i.e.
background noise disappears
• Sensitivity is the min. RF signal to produce a
specified level of quieting.
![Page 8: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/8.jpg)
Sensitivity example
• An FM receiver provides a voltage gain of
200,000(106dB) prior to its limiter. The limiter’s
quieting voltage is 200 mV. What is the
receiver’s sensitivity?receiver’s sensitivity?
200 mV/200,000= 1µV->sensitivity of receiver
![Page 9: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/9.jpg)
Discriminator
• The heart of FM is this relationship
• What we need is a device that linearly follows
inst. frequency
fi(t)=fc+kfm(t)
inst. frequency
Disc.output
f
Deviation limits
+75 KHz-75 KHz
fcarrier
fcarrier is at the IF frequency
Of 10.7 MHz (Fixed for all
channels)
![Page 10: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/10.jpg)
Examples of discriminators
• Slope detector - simple LC tank circuit
operated at its most linear response curve
output
fc fo
output
f
![Page 11: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/11.jpg)
Phase-Locked Loop
• PLL’s are increasingly used as FM
demodulators and appear at IF output
Phase Lowpassfin Error signal
Output proportional toDifference between fin and fvcoPhase
comparatorLowpass
filter
VCO
fin Error signal
fvcoVCO input
Control signal:constantWhen fin=fvco
![Page 12: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/12.jpg)
Zero crossing detector
Hard
limiter
Zero
Crossing
detector
Multi-
vibrator
Averaging
circuit
FM Output
FM input
Hard limiter
ZC detector
multiV
more frequent
ZC’s means
higher inst freq
in turn means
Larger message
amplitudes
Averaging circuit
![Page 13: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/13.jpg)
FM Receiver• After Limiter and Discriminator, Signal is Passed through various Filter
Circuits.• Output of Filters is De-Emphasized and Audio Signals obtained as L and
R separate channels of Stereophonic Receiver.• Pilot Freq. Signal after extracted from Filter Used as Synchronous
Detector Carrier for DSBSC Modulated Waves.
![Page 14: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/14.jpg)
Noise In Communication System
A. External Noise:
(1)Atmospheric Noise
(2)Extraterrestrial Noise
B. Internal Noise:
(1) Thermal Agitation
Noise(2)Extraterrestrial Noise
• Solar Noise
• Cosmic Noise
(3) Industrial Noise
(2) Shot Noise
(3) Transit Time Noise
![Page 15: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/15.jpg)
Noise Calculations
(1) Addition of Noise Due to Several Sources
(2) Addition of Noise Due to Several Amplifier
![Page 16: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/16.jpg)
NOISE IN ANALOG MODULATION
AMPLITUDE MODULATION
![Page 17: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/17.jpg)
Channel model
•Distortionless
•Additive White Gaussian Noise (AWGN)
No/2Flat noise spectrum:white noise
W-W
No/2Flat noise spectrum:white noise
Noise power=hatched area
![Page 18: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/18.jpg)
Receiver Model
• The objective here is to establish a relationship
between input and output SNR of an AM
receiver
BPF detector
Noise n(t)
Modulated signal s(t)
output
filter
fc-fc
BT=2W
![Page 19: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/19.jpg)
Establishing a reference SNR
• Define “channel” SNR measured at receiver
input.
![Page 20: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/20.jpg)
![Page 21: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/21.jpg)
=
![Page 22: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/22.jpg)
The output of the product modulator isThe output of the product modulator is
![Page 23: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/23.jpg)
![Page 24: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/24.jpg)
Therefore, any reduction in input SNR is
linearly reflected in the output.
![Page 25: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/25.jpg)
![Page 26: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/26.jpg)
![Page 27: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/27.jpg)
• Following a similar approach,
( )( )
index modulation AM:
11
2
2
k
Pk
Pk
SNR
SNR
a
a
c
o <+
=
• Best case is achieved for 100% modulation index which, for tone modulation ( Ka
2 = P/2), is only 1/3
power message avg.:P
![Page 28: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/28.jpg)
DSB-AM and DSB-SC noise
performance
• An AM system using envelope detection needs
3 times as much power to achieve the same
output SNR as a suppressed carrier AM with
coherent detectioncoherent detection
• This is a result similar to power efficiency of
the two schemes
![Page 29: Unit 3 - 02 FM-Transmitter & Receiver- and Noise.pdf](https://reader030.fdocuments.us/reader030/viewer/2022020112/5695d12a1a28ab9b029568e2/html5/thumbnails/29.jpg)
Threshold effect-AM
• In DSB-AM (not DSB-SC) there is a
phenomenon called threshold effect
• This means that there is a massive drop in
output SNR if input SNR drops below a output SNR if input SNR drops below a
threshold
• For DSB-AM with envelope detection, this
threshold is about 6.6 dB