Machining Surface Finish Chart, Conversion, Comparator, Method, Degree, Ra, Rz, RMS
Ultra-Refined Universal Cutter...Improved Milling Quality Excellent Surface Quality WEZ Series...
Transcript of Ultra-Refined Universal Cutter...Improved Milling Quality Excellent Surface Quality WEZ Series...
No.528
SEC-WAVEMILL
Rev. 4
High-Precision Shoulder Milling Cutter
for General Purpose Applications
Ultra-Refined "Universal" Cutter
Expanded to 104 insert items
Series expansion with 23
modular type items
Expansion
Expansion
series
Tooling News
Face Milling Shoulder Milling Side Milling Slotting
Plunge MillingRamping Helical MillingHole Expansion Milling
SEC-WAVEMILLseries
(WEZ11 Type)
VIDEO OFCUTTING
2
█ Cutter Body Series
█ Supports Ramping/Helical Milling/Plunge Milling Applicable to various applications Wide Guide Face
for Stable Insert Clamping
█ Optimised Body Design
Typ
e
Cat. No.Diameter Range (mm)
ø14 ø16 ø18 ø20 ø22 ø25 ø26 ø28 ø30 ø32 ø35 ø40 ø50 ø63 ø80 ø100 ø125 ø160
She
ll Ty
pe
WEZ 11000RS 4 65 7
6 8
7 10
9 12
WEZ 11000R Inch7 10
9 12
WEZ 17000RS 3 43 5
4 6
4 7
5 8
6 11
9 8 12
10
WEZ 17000R Inch4 7
5 8
6 11
9 8 12
10
Sha
nk T
ype
WEZ 11000E 1 2 * 22 * 3 *
32 4 *
3 * 4 42 4
3 5 *
52 6
4 5 7
8 10
WEZ 11000EL 1 2 * 2 2 * 2 2 * 3 2 2 2 * 32 3
2 3
WEZ 17000E 2 * 2 3 2 3 * 3 3 43 * 5 *
4 * 6 *
7
WEZ 17000EL 2 2 2 2 * 3 22 4
3
3 * 5 *
4 * 6 *
Mod
ular WEZ 11000M 2 2
2 3
32 4
3 4 5
4 5
2 5
4 24
3 5
2 5
2 5
4 6
WEZ 17000M 2 3 2 2 32 4
3 2 3
24
3
Number in D shows the number of teeth (expanded items are shown in red with white borders) Inch Inch Bore * mark: Different-diameter shanks in stock
Expansion
Expansion
█ Features
D Supports Various Machining OperationsCutter lineup from ø14 to ø160mm, that enables large angle ramping. 15 modular type catalog item expansion.
D Excellent Machining QualityWith a combination of optimised cutting edge shape and high-precision molding technology, superb wall surface accuracy and surface finish quality are achieved.
D Excellent Sharpness with Low ResistanceReduces machining noise and suppresses burrs. Lineup includes ground inserts with emphasis on sharpness.
D General-purpose Grade Applicable to Any Work Material
Introducing the new ACU2500 grade, applicable to a wide range of materials from steel, stainless steel to cast iron.
Chipbreaker
S TypeP TypeF TypeH TypeG TypeL Type
Cut
ting
Edge
Fig
ure
11 Type Not Available
17 Type
ApplicationsLight CuttingLow-rigidity Machining
Main Chipbreaker General-purpose to Interrupted Milling
Heavy CuttingHeavy Interrupted
MachiningHardened Steel
Light Cutting Medium Finishing
Burr Prevention
Light Cutting High-precision Machining
High Wall Surface Squareness
For Non-Ferrous Metals
10°20°
28°
28°28°28°
28° 28°20°28°
0.05mm
0.05mm
0.15mm
0.15mm 0.2mm
28°
Work Materials
Cat. No.Diameter (mm)
AOET11T3SSPEER
AOET1705SSPEER
ø16ø14
Not AvailableNot Available
Not AvailableNot
Available
ø18 ø20 ø22 ø25 ø28 ø30 ø32 ø35 ø40 and above
AO T17 Type AO T11 Type
S
L GH
F,P
Cutting Edge Strength Higher
Goo
dS
harp
ness
Non-ferrous Metal Steel, Stainless Steel, Cast Iron, Heat-resistant Alloy, Titanium Alloy, Hardened SteelH
-P16 -P20 -P25
-P25 -P32
-P16 -P20 -P25
-P25 -P32
-P
-P
-P
-P
3
SEC-WAVEMILL
WEZ series
█ Chipbreaker Lineup
█ Insert Series D: Standard stocked item
█ P Type Chipbreaker Selection Guide
█ Insert Size Comparison
█ Chipbreaker Selection Guide
P type chipbreaker Cat. No. is specific to a range of cutter diameters. For details, check the table below.
Cat. No.Nose Radius (mm)
R0.2 R0.4 R0.5 R0.8 R1.0 R1.2 R1.6 R2.0 R2.4 R3.0 R3.2 R4.0 R5.0 R6.4
AOMT11T3SSPEER-G D D D D D D D D D D D
AOMT11T3SSPEER-H D D D D
AOET11T3SSPEER-F D D D D D D D D D D D
AOET11T3SSPEER-P16 D D D D
AOET11T3SSPEER-P20 D D D D
AOET11T3SSPEER-P25 D D D D
AOET11T3SSPEFR-S D D D D D D D D D D D
AOMT1705SSPEER-L D D D D D
AOMT1705SSPEER-G D D D D D D D D D D D D D D
AOMT1705SSPEER-H D D D D
AOET1705SSPEER-F D D D D D D D D D D D D D D
AOET1705SSPEER-P25 D D D D
AOET1705SSPEER-P32 D D D D
AOET1705SSPEFR-S D D D D D D D D D D D D D D
10
-10
5
-5
0
(μm)
ae
Cutting width 5mm
Second Cut (6mm)
Third Cut (6mm)
Fourth Cut (6mm)
First Cut (6mm)
24mm
18mm
12mm
6mm
0mm0mm
Should
er Height S
houl
der
Hei
ght
Competitor's Product A
WEZ Series
0
5
10
15
20
25
0.050.040.030.020.010-0.01
Should
er
Heig
ht
(mm
)
Deviation (mm)
ap
D Excellent squareness
█ Improved Machining Quality
D Excellent Surface Quality
WEZ Series Competitor's Product B
Ra 0.5μm, Rz 3.3μm Ra 1.2μm, Rz 5.1μm
Machine: Vertical Machining Centre BT40, Work Material: S50C
Tool: WEZ 11020E03 (ø20, 3 flutes)
Insert: AOMT 11T308PEER-G (ACU2500)
Cutting Conditions: vc = 150m/min, fz = 0.15mm/t, ap = 6mm x 4 passes, ae = 5mm Dry
Machine: Vertical Machining Centre BT40, Work Material: S50C
Tool: WEZ 11020E03 (ø20, 3 flutes)
Insert: AOMT 11T308PEER-G (ACU2500)
Cutting Conditions: vc = 150m/min, fz = 0.15mm/t, ap = 6mm x 4 passes, ae = 5mm Dry
Machine: Vertical Machining Centre BT50,
Work Material: SCM440
Tool: WEZ 17100RS08 (ø100, 8 flutes)
Insert: AOMT 170508PEER-G (ACU2500)
Cutting Conditions: vc = 250m/min, fz = 0.15mm/t,
ap = 2mm, ae = 85mm, Dry
Machine: Vertical Machining Centre BT50,
Work Material: SCM440
Tool: WEZ 17100RS08 (ø100, 8 flutes)
Insert: AOMT 170508PEER-G (ACU2500)
Cutting Conditions: vc = 250m/min, fz = 0.15mm/t,
ap = 2mm, ae = 85mm, Dry
Machine: Vertical Machining Centre BT40, Work Material: S50C
Tool: WEZ 11020E03 (ø20, 3 flutes)
Insert: AOMT 11T308PEER-G (ACU2500)
Cutting Conditions: vc = 150m/min, fz = 0.15mm/t, ap = 8mm, ae = 5mm Dry
Machine: Vertical Machining Centre BT40, Work Material: S50C
Tool: WEZ 11020E03 (ø20, 3 flutes)
Insert: AOMT 11T308PEER-G (ACU2500)
Cutting Conditions: vc = 150m/min, fz = 0.15mm/t, ap = 8mm, ae = 5mm Dry
Nois
e level
(dB
)
73
75
77
Competitor's Product C
Quiet
WEZ Series
D Lower cutting force helps reduce machining noise
0.1mm 0.1mm
4
SEC-WAVEMILL
WEZ series
█ Sharp edged chipbreaker, with excellent adhesion resistance, for milling non-ferrous metals
Machine: Vertical Machining Centre BT30, Work Material: ADC12
Tool: WEZ 11020E03 (ø20, 3 flutes)
Insert: AOET 11T308PEFR-S (H20)
Cutting Conditions: vc = 350m/min, fz = 0.1mm/t, ap = 3mm,
ae = 10mm Dry
Competitor's Product E
Adhesion
WEZ Series
No Adhesion
D Burr Control with Edge Sharpness
█ Cutting Edge Specialized for Sharpness
Area Prone To Burrs
Approx. 2mm
WEZ Series Competitor's Product D
Machine: Vertical Machining Centre BT50, Work Material: SUS304
Tool: WEZ 11050RS07 (ø50, 7 flutes)
Insert: AOET 11T308PEER-F (ACU2500)
Cutting Conditions: vc = 120m/min, fz = 0.12mm/t, ap = 1mm, ae = 30mm Dry
█ Realizes wall squareness equivalent to solid endmills
Machine: Vertical Machining Centre BT50, Work Material: S50C
Tool: WEZ 11020E03 (ø20, 3 flutes)
Insert: AOET 11T308PEER-P20 (ACU2500)
Cutting Conditions: vc = 150m/min, fz = 0.1mm/t,
ap = 8mm x 3 Passes, ae = 1mm, Dry
Solid Endmills
WEZ Series
0
10
20
-0.0200.020.040.06
Should
er
Heig
ht
(mm
)
Deviation (mm)
█ Lineup of Chipbreakers for Ground Inserts
F Type P Type S Type
· Sharpness from ground finish suppresses burr formation
· Good wall accuracy with all cutter diameters
· Premium item with cutting edge shape optimised for each cutter diameter while maintaining the F Type chipbreaker's sharpness
· Enables wall squareness equal to using solid endmills, through cutting edge shape optimization for each cutter diameter
· Suppresses adhesion with rake face lapping
· DLC Coat inserts available for further improved adhesion resistance
5
SEC-WAVEMILL
WEZ series
█ Grade Features
CVD PVD
5nm
█ Insert Grade Selection Guide
New ABSOTECH® (absolute technology) coating technology that realises absolute stability
: CVD : PVDC PThe letters "C" and "P" at the end of each grade indicate the coating type.
Stainless SteelM
SteelP
Work Material Finishing to Light Cut Rough to Heavy CutMedium Cut
Coa
ting
Coa
ting
Cerm
et
CACM200
P ACM300
Non-ferrous MetalN
Work Material Finishing to Light Cut Rough to Heavy CutMedium Cut
Coa
ting
Coa
ting
Car
bid
e
Cast IronK
CACP2000
P ACU2500
P ACU2500
P ACP3000
CACK2000
P ACK3000
H20
P ACU2500
T2500AP DL2000
Work Materials Grades Coating Thickness(μm) Features
ACU2500
ACP2000
ACP3000
T2500A
ACM200
ACM300
ACK2000
ACK3000
DL2000
H20
3
10
3
—
6
3
10
3
0.5
—
Coating Type
Absotech
Absotech
Absotech
—
Absotech
Absotech
AURORA Coat
(DLC)
—
General-purpose grade applicable to steel, stainless steel, and cast iron
Utilizing a carbide substrate with excellent fracture and wear resistance,
coupled with a new coating with excellent wear and chipping resistance, to
achieve long and stable tool life in various of work materials.
A cermet grade with both high fracture and wear resistance, due to its
excellent thermal crack resistance conferred by high thermal conductivity,
and improved toughness from its dense and uniform structure.
Realises superb stability in machining of high-hardness stainless steel, due to
a high-strength carbide substrate and highly wear-resistant coating.
Realises superb stability in machining of stainless steel, due to a
high-strength carbide substrate and highly chipping-resistant coating.
Stable long tool life in high-speed machining of cast iron is realised by
adopting a new coating with excellent thermal resistance and a tough
carbide substrate.
Utilizing a carbide substrate with excellent wear resistance, coupled with a
new coating with excellent wear and chipping resistance to achieve long and
stable tool life in dry machining of cast iron.
Utilizing a very tough carbide substrate, coupled with a new coating with
excellent wear and chipping resistance to achieve long and stable tool life
especially in wet machining of steel.
Stable long tool life in high-speed machining is realised by adopting a new
coating and a tough carbide substrate with excellent thermal crack
resistance.
Special Surface Treatment
High Hardness TiCN
Crystal Orientation Control Al2O3
Al2O3
TiCNLayer
Carbide substrate Carbide
substrate
High Adhesion StrengthIncreased TiCN hardness by using a C-rich composition for flank wear resistance more than twice of conventional types
Applicable Grades: ACU2500, ACP3000, ACK3000Applicable Grades: ACP2000, ACK2000
Higher hardness and twice the conventional wear resistance due to a fine crystal structure AlTiCrBN-based nano-layered coating
The WEZ series can be combined with multiple new insert grades. In particular, the newly developed general-purpose ACU2500 grade suitable for various work materials has now been released.In addition to the coated grades for milling steel, stainless steel, cast iron and aluminum alloy, the lineup is enhanced with cermet and uncoated carbide grades.
Suppresses thermal cracking by introducing high compressive stress, resulting in chipping resistance more than twice of conventional types
By controlling the growth direction, Al2O3 is reinforced for crater wear resistance more than twice of conventional types
Increased TiCN hardness by using a C-rich composition for flank wear resistance more than twice of conventional types
Cross Section of Cutting Edge Coating TEM Image
New Super Multi-Layered Composition
DLC coated grade for non-ferrous metal machining with a low coefficient of
friction and excellent adhesion resistance.
Uncoated grade for non-ferrous metal machining with excellent wear
resistance and fracture resistance.
Super
FF Coat
(New)
Super
ZX Coat
6
SEC-WAVEMILL
WEZ series
P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy
Cutting Width ae = 16mm
Depth of Cut ap = 5mm
Work Material
ISO
Cla
ssifi
catio
n
ACP2000 ACP3000 T2500A ACK3000 ACM200 ACM300 DL2000ACU2500
125190250270300180275300350200325200240180
285-335-390180-230-285145-190-230115-150-185 70- 90-115170-220-265100-130-155 90-115-140 65- 85-100145-185-230 55- 75- 90115-145-175105-130-155125-155-190160-210-265 95-125-160 30- 40- 60 60- 85-105
315-360-420210-265-315170-210-255135-170-205 85-105-125200-245-295115-145-175105-130-155 75- 95-115170-215-255 65- 85-100
265-315-370160-210-265130-170-215100-135-170 65- 85-105150-200-250 85-115-145 75-105-130 55- 75- 95130-170-215 50- 65- 85
240-295-345135-190-240110-155-195 90-125-155 55- 75- 95130-180-225 75-105-135 65- 90-120 50- 70- 85
500-750-1000170-200- 250300-330- 350
265-315-370160-190-220
180-230-285105-140-170
100-115-145 85-105-130105-125-160
25- 35- 50 50- 75- 95
145-175-195130-155-175160-190-210
35- 45- 60 75- 95-115
GGGGGGGGGGGGGGGGGGSSS
Chi
pb
reak
er
Wor
k M
ater
ial
Har
dne
ss (H
B)
Steel, Carbon Steel S15C S45C S45C Hardened S75C S75C HardenedLow Alloy Steel SCM, SNCM SCM, SNCM Hardened SCM, SNCM Hardened SCM, SNCM HardenedHigh Alloy Steel SKD, SKT, SKH SKD, SKT, SKH HardenedStainless Steel SUS430 and Others (Martensitic/Ferritic) SUS403 and Others (Martensitic/Hardened) SUS304, SUS316 (Austenitic)Cast IronDuctile Cast IronExotic Alloy Heat-Resistant Alloy Ti AlloyAluminum Alloy Si content of 12.6% or less Si content of over 12.6%Copper Alloy
0.10-0.20-0.28 -0.15-0.10 0.22 0.10-0.20-0.28 0.10-0.20-0.28 0.10-0.20-0.28 0.10-0.20-0.28 0.05-0.10-0.150.10-0.20-0.280.10-0.20-0.28
Grade
Feed Rate per Tooth fz (mm/t) Min. - Optimum - Max.
Cutting Speed vc (m/min) Min. - Optimum - Max.
ACK2000
N
P
K
S
M
D The recommended cutting conditions may not be practical depending on the operating conditions (e.g. machine, work material shape, clamping system).D For groove milling, adjust the feed rate to around 70% of the above values.
The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work material rigidity, depth of cut and other factors.Note
WEZ17 TypeTool: WEZ17032E03, Insert: AO T1705 TypeCutting Conditions: Depth of Cut ap = 5mm, Width of Cut ae = 16mm, Dry
Tool: WEZ11020E03, Insert: AO T11T3 TypeCutting Conditions: Depth of Cut ap = 3mm, Width of Cut ae = 10mm, Dry
█ Recommended Cutting Conditions
Work Material
ISO
Cla
ssifi
catio
n
ACP2000 ACP3000 T2500A ACK3000 ACM200 ACM300 DL2000
125190250270300180275300350200325200240180
270-320-370170-220-270140-180-220110-145-175 70- 90-110160-205-255 95-120-150 85-110-130 60- 80-100140-180-220 55- 70- 85110-140-170100-125-150120-150-180150-200-250 90-120-150 30- 40- 55 60- 80-100
300-350-400200-250-300160-200-245130-165-195 80-100-120190-235-280110-135-165100-125-150 70- 90-110160-200-245 60- 80-100
250-300-350150-200-250120-160-200100-130-165 60- 80-100140-190-235 80-110-140 75-100-125 50- 70- 90120-160-205 50- 65- 80
230-280-330130-180-230105-145-18585-115-150 50- 70- 90120-170-215 70-100-125 65- 90-115 45- 65- 85
500-750-1000170-200- 250300-330- 350
250-300-350150-180-210
170-220-270100-130-160
90-110-140 80-100-125100-120-150
25- 35- 50 50- 70- 90
140-170-190125-150-170150-180-200
35- 45- 60 70- 90-110
GGGGGGGGGGGGGGGGGGSSS
Chi
pb
reak
er
Wor
k M
ater
ial
Har
dne
ss (H
B)
Steel, Carbon Steel S15CS45CS45C HardenedS75CS75C Hardened
Low Alloy Steel SCM, SNCM SCM, SNCM Hardened SCM, SNCM Hardened SCM, SNCM HardenedHigh Alloy Steel SKD, SKT, SKH SKD, SKT, SKH HardenedStainless Steel SUS430 and Others (Martensitic/Ferritic) SUS403 and Others (Martensitic/Hardened) SUS304, SUS316 (Austenitic)Cast IronDuctile Cast IronExotic Alloy Heat-Resistant Alloy Ti AlloyAluminum Alloy Si content of 12.6% or less Si content of over 12.6%Copper Alloy
0.08-0.15-0.20 0.08-0.12-0.18 0.08-0.15-0.20 0.08-0.15-0.20 0.08-0.15-0.20 0.08-0.15-0.20 0.05-0.10-0.150.08-0.15-0.200.08-0.15-0.20
Grade
Feed Rate per Tooth fz (mm/t) Min. - Optimum - Max.
Cutting Speed vc (m/min) Min. - Optimum - Max.
ACK2000
N
P
M
K
S
WEZ11 Type
D The recommended cutting conditions may not be practical depending on the operating conditions (e.g. machine, work material shape, clamping system).D For groove milling, adjust the feed rate to around 70% of the above values.
The cutting conditions above are a guide. Actual conditions will need to be adjusted according to machine rigidity, work material rigidity, depth of cut and other factors.Note
Cutting Width ae = 10mm
Depth of Cut ap = 3mm
ACU2500
7
SEC-WAVEMILL
WEZ series
DCWork Dia.
Pitch
DCWork Dia.
Pitch
DC
RMPX ap
ae
Diameter DC
Max. Ramping AngleRMPX (°)
Flat bottom machining Machining with prepared hole
Maximum Pitch(mm/rev)
Min. Machining Dia.(mm)
Maximum Pitch(mm/rev)
Max. Machining Dia.(mm)
Maximum Pitch(mm/rev)
Min. Machining Dia.(mm)
25
28
30
32
35
40
50
63
10.8
8.1
7.0
6.1
5.1
4.0
2.5
1.8
47.3
53.3
57.3
61.3
67.3
77.3
97.3
123.3
13.0
11.1
10.2
9.5
8.7
7.7
6.5
5.6
8.3
7.5
7.0
6.7
6.2
5.7
5.0
4.5
33.1
39.0
43.0
47.0
53.0
63.0
83.0
109.0
1.8
1.8
1.8
1.7
1.7
1.7
1.6
1.6
41.0
46.9
50.9
54.9
60.8
70.8
90.7
116.7
█ Plunge Milling Upper Limits
Max. ae
(mm)
WEZ11 Type
WEZ17 Type
3
5
Diameter DC
Max. Ramping AngleRMPX (°)
Flat bottom machining Machining with prepared hole
Maximum Pitch(mm/rev)
Min. Machining Dia.(mm)
Maximum Pitch(mm/rev)
Max. Machining Dia.(mm)
Maximum Pitch(mm/rev)
Min. Machining Dia.(mm)
14
16
18
20
22
25
28
30
32
35
40
50
63
8.0
10.5
8.1
6.5
5.3
4.1
3.4
3.0
2.7
2.3
1.8
1.2
0.8
25.3
29.3
33.3
37.3
41.3
47.3
53.3
57.3
61.3
67.3
77.3
97.3
123.3
5.0
7.6
6.7
6.0
5.4
4.8
4.4
4.2
4.0
3.8
3.4
3.0
2.8
3.4
5.6
5.0
4.6
4.3
3.9
3.6
3.5
3.3
3.1
2.9
2.6
2.5
19.0
21.7
25.2
29.1
32.9
38.9
44.9
48.8
52.8
58.8
68.8
88.8
114.7
1.5
1.5
1.4
1.3
1.3
1.3
1.3
1.3
1.2
1.2
1.2
1.1
1.1
23.1
27.0
30.9
34.9
38.8
44.8
50.7
54.7
58.7
64.6
74.6
94.6
120.5
█ Ramping/Helical Milling Upper Limits
WEZ11 Type
WEZ17 Type
*The table above shows values with nose radius 0.8mm.
Ramping Flat bottom machining Machining with prepared hole
8
SEC-WAVEMILL
WEZ series
Shoulder accuracy
Surface Finish
Cutting Edge Strength
No. of Cutting Edges
Chip Control
Cutting resistance
TSX series WEZ series
DFC series WFX series
Double-Sided, 4 Corners Single-Sided, 2 Corners
Double-Sided, 6 Corners Single-Sided, 4 Corners
█ Shoulder Milling Cutter Selection Guide
WFX series
WEZ series
DFC series
TSX series
Surface Finish
Shoulder Accuracy
Cutting Resistance
Chip Control
No. of CuttingEdges
Cutting EdgeStrength
*For the details of each product, see the TSX series (Tooling News No. 523), DFC series (Tooling News No. 513), and WFX series (Tooling News No. 491).
: Top recommendation
9
SEC-WAVEMILL
WEZ series
Fig 1
DCSFMS
KWW
DCB
LF
D2
D1
DC
KD
PC
BD
P
Fig 2DCSFMS
KWW
DCB
LF
D1
DC
KD
PC
BD
P
D2
D3
Fig 3DCSFMS
KWW
DCB
LF
D1
DC
KD
PC
BD
P
10
SEC-WAVEMILL
WEZ 11000R(S) type
█ Identification Code
WEZ 11 050 R S 07Series Insert
SizeDia. Feed
DirectionMetric Number
of Teeth
Check the collet mounting size (DCB) when selecting the cutter. Inserts are sold separately.
For mounting the ø80 and ø100mm sized cutters marked with * to an arbor, use a JIS B1176 hex socket bolt (ø80: M12 x 30 to 35mm, ø100: M16 x 40 to 45mm).
█ Body (Shell Type)
Cat. No.
Sto
ck Dia. Boss Height Bore Dia. Keyway Width
Keyway Depth
Mounting Depth Bolt Bolt Bolt Number
of TeethWeight
(kg) FigDC DCSFMS LF DCB KWW KDP CBDP D1 D2 D3
Met
ric
WEZ 11040RS04 D 40 33 40 16 8.4 5.6 18 14 9 Q 4 0.21 1WEZ 11040RS06 D 40 33 40 16 8.4 5.6 18 14 9 Q 6 0.20 1WEZ 11050RS05 D 50 41 40 22 10.4 6.3 20 18 11 Q 5 0.32 1WEZ 11050RS07 D 50 41 40 22 10.4 6.3 20 18 11 Q 7 0.31 1WEZ 11063RS06 D 63 50 40 22 10.4 6.3 20 18 11 Q 6 0.58 1WEZ 11063RS08 D 63 50 40 22 10.4 6.3 20 18 11 Q 8 0.57 1WEZ 11080RS07 D *80 55 50 27 12.4 7 22 20 14 Q 7 1.08 1WEZ 11080RS10 D *80 55 50 27 12.4 7 22 20 14 Q 10 1.07 1WEZ 11100RS09 D 100 70 50 32 14.4 8 32 46 Q Q 9 1.57 3WEZ 11100RS12 D 100 70 50 32 14.4 8 32 46 Q Q 12 1.56 3
Inch
WEZ 11080R07 D *80 55 50 25.4 9.5 6 25 20 14 Q 7 1.09 1WEZ 11080R10 D *80 55 50 25.4 9.5 6 25 20 14 Q 10 1.08 1WEZ 11100R09 D *100 70 63 31.75 12.7 8 32 46 27 18 9 2.12 2WEZ 11100R12 D *100 70 63 31.75 12.7 8 32 46 27 18 12 2.10 2
Dimensions (mm)
█ Spare Parts
Applicable Cutter
Screw Integrated Wrench
Anti-seizure Cream
N m
WEZ11040RS04
BFTX0306IP 1.5 TRDR08IP SUMI-P
WEZ11040RS06WEZ11050RS05WEZ11050RS07WEZ11063RS06WEZ11063RS08WEZ11080R(S)07WEZ11080R(S)10WEZ11100R(S)09WEZ11100R(S)12
N m Recommended Tightening Torque (N·m)
D mark: Standard stocked item
Rake Angle
Radial –7° to –11°
Axial 14° to 15°
12.8 3.6
7.5 2
0°
RE
11
SEC-WAVEMILL
WEZ 11000R(S) type
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT11T324PEER)Nose radius = 3.0: C1(AOMT11T330PEER)Nose radius = 3.2: C1(AOMT11T332PEER)
Standard: R1.
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT11T302PEER-G D D D D D D D Q Q D 0.2AOMT11T304PEER-G D D D D D D D Q Q D 0.4AOMT11T305PEER-G D S S S S S S Q Q S 0.5AOMT11T308PEER-G D D D D D D D Q Q D 0.8AOMT11T310PEER-G D S S S S S S Q Q S 1.0AOMT11T312PEER-G D S S S S D D Q Q S 1.2AOMT11T316PEER-G D S S S S S S Q Q 1.6AOMT11T320PEER-G D S S S S D D Q Q 2.0AOMT11T324PEER-G D S S S S S S Q Q 2.4AOMT11T330PEER-G D S S S S D D Q Q 3.0AOMT11T332PEER-G D S S S S S S Q Q 3.2AOMT11T304PEER-H D D D D D D D Q Q Q 0.4AOMT11T308PEER-H D D D D D D D Q Q Q 0.8AOMT11T312PEER-H D S S S S D D Q Q Q 1.2AOMT11T316PEER-H D S S S S S S Q Q Q 1.6AOET11T302PEER-F D Q Q Q Q Q Q 0.2AOET11T304PEER-F D Q Q Q Q Q Q 0.4AOET11T305PEER-F D Q Q Q Q Q Q 0.5AOET11T308PEER-F D Q Q Q Q Q Q 0.8AOET11T310PEER-F D Q Q Q Q Q Q 1.0AOET11T312PEER-F D Q Q Q Q Q Q 1.2AOET11T316PEER-F D Q Q Q Q Q Q 1.6AOET11T320PEER-F D Q Q Q Q Q Q 2.0AOET11T324PEER-F D Q Q Q Q Q Q 2.4AOET11T330PEER-F D Q Q Q Q Q Q 3.0AOET11T332PEER-F D Q Q Q Q Q Q 3.2AOET11T302PEER-P16 D Q Q Q Q Q Q 0.2AOET11T304PEER-P16 D Q Q Q Q Q Q 0.4AOET11T305PEER-P16 S Q Q Q Q Q Q 0.5AOET11T308PEER-P16 D Q Q Q Q Q Q 0.8AOET11T310PEER-P16 S Q Q Q Q Q Q 1.0AOET11T312PEER-P16 D Q Q Q Q Q Q 1.2
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET11T302PEER-P20 D Q Q Q Q Q Q 0.2AOET11T304PEER-P20 D Q Q Q Q Q Q 0.4AOET11T305PEER-P20 S Q Q Q Q Q Q 0.5AOET11T308PEER-P20 D Q Q Q Q Q Q 0.8AOET11T310PEER-P20 S Q Q Q Q Q Q 1.0AOET11T312PEER-P20 D Q Q Q Q Q Q 1.2AOET11T302PEER-P25 D Q Q Q Q Q Q 0.2AOET11T304PEER-P25 D Q Q Q Q Q Q 0.4AOET11T305PEER-P25 S Q Q Q Q Q Q 0.5AOET11T308PEER-P25 D Q Q Q Q Q Q 0.8AOET11T310PEER-P25 S Q Q Q Q Q Q 1.0AOET11T312PEER-P25 D Q Q Q Q Q Q 1.2AOET11T302PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET11T304PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET11T305PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET11T308PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET11T310PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET11T312PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET11T316PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET11T320PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET11T324PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET11T330PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET11T332PEFR-S Q Q Q Q Q Q Q D D Q 3.2
-G: General-purpose, -H: Strong Edge, -F: Medium Finishing, -P16/-P20/-P25: High-precision Machining,
-S: Non-ferrous metals.
* -P16 is applicable to cutter diameters ø14 and ø16. -P20 is applicable to cutter diameters ø18 and ø20.
-P25 is applicable to cutter diameters ø25 and ø28.
Recommended Cutting Conditions P7
( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)█ Insert
Fig 1
DCSFMS
KWW
DCB
LF
D2
D1
DC
KD
PC
BD
P
Fig 2
DCSFMS
KWW
DCB
LF
D1
DC
KD
PC
BD
P
D2
D3
Fig 3
DCSFMS
KWW
DCB
LF
D1
DC
KD
PC
BD
P
Fig 4
DCSFMS
KWW
DCB
LF
D1
DC
KD
P
CB
DP
Fig 5 DCSFMS
KWW
DCB
LF
D1
DC
KD
P
CB
DP
ø66.74-ø14
12
SEC-WAVEMILL
WEZ 17000R(S) type
N m Recommended Tightening Torque (N·m)
█ Spare Parts
Applicable Cutter
Screw Integrated Wrench
Detachable Wrench Handle Grip
Detachable Wrench Bit
Anti-seizure Cream
N m
WEZ17040RS03
BFTX0409IP 3.0
Q HPS1015 TRB15IP
SUMI-P
WEZ17040RS04WEZ17050RS03WEZ17050RS05WEZ17063RS04WEZ17063RS06WEZ17080R(S)04WEZ17080R(S)07WEZ17100R(S)05WEZ17100R(S)08WEZ17125R(S)06WEZ17125R(S)09WEZ17125R(S)11WEZ17160R(S)08
TRDR15IP Q QWEZ17160R(S)10WEZ17160R(S)12
█ Body (Shell Type)
Cat. No.
Sto
ck Dia. Boss Height Bore Dia. Keyway Width
Keyway Depth
Mounting Depth Bolt Bolt Bolt Number
of TeethWeight
(kg) FigDC DCSFMS LF DCB KWW KDP CBDP D1 D2 D3
Met
ric
WEZ 17040RS03 D 40 33 40 16 8.4 5.6 18 14 9 Q 3 0.19 1WEZ 17040RS04 D 40 33 40 16 8.4 5.6 18 14 9 Q 4 0.16 1WEZ 17050RS03 D 50 41 40 22 10.4 6.3 20 18 11 Q 3 0.30 1WEZ 17050RS05 D 50 41 40 22 10.4 6.3 20 18 11 Q 5 0.26 1WEZ 17063RS04 D 63 50 40 22 10.4 6.3 20 18 11 Q 4 0.54 1WEZ 17063RS06 D 63 50 40 22 10.4 6.3 20 18 11 Q 6 0.51 1WEZ 17080RS04 D *80 55 50 27 12.4 7 22 20 14 Q 4 1.10 1WEZ 17080RS07 D *80 55 50 27 12.4 7 22 20 14 Q 7 1.05 1WEZ 17100RS05 D 100 70 50 32 14.4 8 32 46 Q Q 5 1.58 3WEZ 17100RS08 D 100 70 50 32 14.4 8 32 46 Q Q 8 1.57 3WEZ 17125RS06 D 125 80 63 40 16.4 9 29 52 29 Q 6 3.04 1WEZ 17125RS09 D 125 80 63 40 16.4 9 29 52 29 Q 9 3.07 1WEZ 17125RS11 D 125 80 63 40 16.4 9 29 52 29 Q 11 3.02 1WEZ 17160RS08 D 160 130 63 40 16.4 9 29 90 Q Q 8 5.24 5WEZ 17160RS10 D 160 130 63 40 16.4 9 29 90 Q Q 10 5.31 5WEZ 17160RS12 D 160 130 63 40 16.4 9 29 90 Q Q 12 5.26 5
Inch
WEZ 17080R04 D *80 55 50 25.4 9.5 6 25 20 14 Q 4 1.10 1WEZ 17080R07 D *80 55 50 25.4 9.5 6 25 20 14 Q 7 1.06 1WEZ 17100R05 D *100 70 63 31.75 12.7 8 32 46 27 18 5 2.08 2WEZ 17100R08 D *100 70 63 31.75 12.7 8 32 46 27 18 8 2.07 2WEZ 17125R06 D 125 80 63 38.1 15.9 10 35.5 55 30 Q 6 3.09 1WEZ 17125R09 D 125 80 63 38.1 15.9 10 35.5 55 30 Q 9 3.11 1WEZ 17125R11 D 125 80 63 38.1 15.9 10 35.5 55 30 Q 11 3.06 1WEZ 17160R08 D 160 100 63 50.8 19.1 11 38 72 Q Q 8 5.04 4WEZ 17160R10 D 160 100 63 50.8 19.1 11 38 72 Q Q 10 5.09 4WEZ 17160R12 D 160 100 63 50.8 19.1 11 38 72 Q Q 12 5.04 4
Check the collet mounting size (DCB) when selecting the cutter. Inserts are sold separately.
For mounting the ø80 and ø100mm sized cutters marked with * to an arbor, use a JIS B1176 hex socket bolt (ø80: M12 x 30 to 35mm, ø100: M16 x 40 to 45mm).
Dimensions (mm)
█ Identification Code
WEZ 17 100 R S 05Series Insert
SizeDia. Feed
DirectionMetric Number
of Teeth
D mark: Standard stocked item
Rake Angle
Radial –4° to –9°
Axial 10° to 15°
19.5 5.5
10
.5
20°
RE
13
SEC-WAVEMILL
WEZ 17000R(S) type
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
-L: Low Cutting Force, -G: General-purpose, -H: Strong Edge, -F: Medium Finishing,
-P25/-P32: High-precision Machining, -S: Non-ferrous metals.
* -P25 is applicable to cutter diameters ø25 and ø28. -P32 is applicable to cutter diameters ø30, ø32 and ø35.
Recommended Cutting Conditions P7
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT170524PEER)Nose radius = 3.0: C1(AOMT170530PEER)Nose radius = 3.2: C1(AOMT170532PEER)Nose radius = 4.0: C2(AOMT170540PEER)Nose radius = 5.0: C5(AOMT170550PEER)Nose radius = 6.4: C5(AOMT170564PEER)
Standard: R1.
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT170502PEER-L D Q S Q S D D Q Q S 0.2AOMT170504PEER-L D Q D Q D D D Q Q D 0.4AOMT170508PEER-L D Q D Q D D D Q Q D 0.8AOMT170512PEER-L D Q S Q S D D Q Q S 1.2AOMT170516PEER-L D Q S Q S D D Q Q 1.6AOMT170502PEER-G D S S S S D D Q Q S 0.2AOMT170504PEER-G D D D D D D D Q Q D 0.4AOMT170505PEER-G D S S S S S S Q Q S 0.5AOMT170508PEER-G D D D D D D D Q Q D 0.8AOMT170510PEER-G D S S S S S S Q Q S 1.0AOMT170512PEER-G D S S S S D D Q Q S 1.2AOMT170516PEER-G D S S S S S S Q Q 1.6AOMT170520PEER-G D S S S S D D Q Q 2.0AOMT170524PEER-G D S S S S S S Q Q 2.4AOMT170530PEER-G D S S S S D D Q Q 3.0AOMT170532PEER-G D S S S S S S Q Q 3.2AOMT170540PEER-G D S S S S S S Q Q 4.0AOMT170550PEER-G D S S S S D D Q Q 5.0AOMT170564PEER-G D S S S S S S Q Q 6.4AOMT170504PEER-H D D D D D D D Q Q Q 0.4AOMT170508PEER-H D D D D D D D Q Q Q 0.8AOMT170512PEER-H D S S S S D D Q Q Q 1.2AOMT170516PEER-H D S S S S S S Q Q Q 1.6AOET170502PEER-F D Q Q Q Q Q Q 0.2AOET170504PEER-F D Q Q Q Q Q Q 0.4AOET170505PEER-F D Q Q Q Q Q Q 0.5AOET170508PEER-F D Q Q Q Q Q Q 0.8AOET170510PEER-F D Q Q Q Q Q Q 1.0AOET170512PEER-F D Q Q Q Q Q Q 1.2AOET170516PEER-F D Q Q Q Q Q Q 1.6AOET170520PEER-F D Q Q Q Q Q Q 2.0AOET170524PEER-F D Q Q Q Q Q Q 2.4AOET170530PEER-F D Q Q Q Q Q Q 3.0
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET170532PEER-F D Q Q Q Q Q Q 3.2AOET170540PEER-F D Q Q Q Q Q Q 4.0AOET170550PEER-F D Q Q Q Q Q Q 5.0AOET170564PEER-F D Q Q Q Q Q Q 6.4AOET170502PEER-P25 D Q Q Q Q Q Q 0.2AOET170504PEER-P25 D Q Q Q Q Q Q 0.4AOET170505PEER-P25 S Q Q Q Q Q Q 0.5AOET170508PEER-P25 D Q Q Q Q Q Q 0.8AOET170510PEER-P25 S Q Q Q Q Q Q 1.0AOET170512PEER-P25 D Q Q Q Q Q Q 1.2AOET170502PEER-P32 D Q Q Q Q Q Q 0.2AOET170504PEER-P32 D Q Q Q Q Q Q 0.4AOET170505PEER-P32 S Q Q Q Q Q Q 0.5AOET170508PEER-P32 D Q Q Q Q Q Q 0.8AOET170510PEER-P32 S Q Q Q Q Q Q 1.0AOET170512PEER-P32 D Q Q Q Q Q Q 1.2AOET170502PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET170504PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET170505PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET170508PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET170510PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET170512PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET170516PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET170520PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET170524PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET170530PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET170532PEFR-S Q Q Q Q Q Q Q D D Q 3.2AOET170540PEFR-S Q Q Q Q Q Q Q D D Q 4.0AOET170550PEFR-S Q Q Q Q Q Q Q D D Q 5.0AOET170564PEFR-S Q Q Q Q Q Q Q D D Q 6.4
█ Insert ( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)
Fig 1 Fig 2
DM
M
LF
LSLH
DC
DM
M
LSLH
DC
LF
Rake Angle
Radial –7° to –18°
Axial 6° to 15°
14
SEC-WAVEMILL
WEZ 11000E type
█ Body (Shank Type)
Cat. No.
Sto
ck Dia. Shank Head Shank Overall LengthNumber of Teeth Weight
(kg) FigDC DMM LH LS LF
WEZ 11014E01 D 14 16 25 55 80 1 0.10 1WEZ 11016E02 D 16 16 25 75 100 2 0.13 1WEZ 11016E02-12 D 16 12 25 75 100 2 0.07 2WEZ 11018E02 D 18 16 25 75 100 2 0.13 2WEZ 11020E02 D 20 20 30 80 110 2 0.23 1WEZ 11020E02-16 D 20 16 30 80 110 2 0.15 2WEZ 11020E03 D 20 20 30 80 110 3 0.22 1WEZ 11020E03-16 D 20 16 30 80 110 3 0.14 2WEZ 11022E03 D 22 20 30 80 110 3 0.23 1WEZ 11025E02 D 25 25 35 85 120 2 0.40 1WEZ 11025E03 D 25 25 35 85 120 3 0.40 1WEZ 11025E03-20 D 25 20 35 85 120 3 0.26 2WEZ 11025E04 D 25 25 35 85 120 4 0.39 2WEZ 11025E04-20 D 25 20 35 85 120 4 0.26 2WEZ 11028E04 D 28 25 35 85 120 4 0.41 1WEZ 11030E04 D 30 25 40 90 130 4 0.46 1WEZ 11032E02 D 32 32 40 90 130 2 0.74 1WEZ 11032E03 D 32 32 40 90 130 3 0.73 1WEZ 11032E04 D 32 32 40 90 130 4 0.73 2WEZ 11032E05 D 32 32 40 90 130 5 0.72 2WEZ 11032E05-25 D 32 25 40 90 130 5 0.46 2WEZ 11035E05 D 35 32 40 90 130 5 0.75 2WEZ 11040E02 D 40 32 30 120 150 2 0.96 2WEZ 11040E04 D 40 32 30 120 150 4 0.94 2WEZ 11040E06 D 40 32 30 120 150 6 0.93 2WEZ 11050E05 D 50 32 30 120 150 5 1.04 2WEZ 11050E07 D 50 32 30 120 150 7 1.04 2WEZ 11063E08 D 63 32 30 120 150 8 1.24 2WEZ 11080E10 D 80 32 30 120 150 10 1.52 2
Inserts are sold separately.
█ Identification Code█ Spare Parts
Applicable Cutter
Flat Screw Integrated Wrench
Anti-seizure Cream
N m
WEZ11014E01BFTX0305IP
1.5 TRDR08IP SUMI-P
WEZ11016E02(-12)WEZ11018E02WEZ11020E02(-16)
BFTX0306IP
WEZ11020E03(-16)WEZ11022E03WEZ11025E02WEZ11025E03(-20)WEZ11025E04(-20)WEZ11028E04WEZ11030E04WEZ11032E02WEZ11032E03WEZ11032E04WEZ11032E05(-25)WEZ11035E05WEZ11040E02WEZ11040E04WEZ11040E06WEZ11050E05WEZ11050E07WEZ11063E08WEZ11080E10
WEZ 11 025 E 03 -20Series Insert
SizeDia. With
ShankNumber of Teeth
Shank Dia.
Dimensions (mm)
N m Recommended Tightening Torque (N·m)
D mark: Standard stocked item
12.8 3.6
7.5 2
0°
RE
15
SEC-WAVEMILL
WEZ 11000E type
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT11T324PEER)Nose radius = 3.0: C1(AOMT11T330PEER)Nose radius = 3.2: C1(AOMT11T332PEER)
Standard: R1.
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT11T302PEER-G D D D D D D D Q Q D 0.2AOMT11T304PEER-G D D D D D D D Q Q D 0.4AOMT11T305PEER-G D S S S S S S Q Q S 0.5AOMT11T308PEER-G D D D D D D D Q Q D 0.8AOMT11T310PEER-G D S S S S S S Q Q S 1.0AOMT11T312PEER-G D S S S S D D Q Q S 1.2AOMT11T316PEER-G D S S S S S S Q Q 1.6AOMT11T320PEER-G D S S S S D D Q Q 2.0AOMT11T324PEER-G D S S S S S S Q Q 2.4AOMT11T330PEER-G D S S S S D D Q Q 3.0AOMT11T332PEER-G D S S S S S S Q Q 3.2AOMT11T304PEER-H D D D D D D D Q Q Q 0.4AOMT11T308PEER-H D D D D D D D Q Q Q 0.8AOMT11T312PEER-H D S S S S D D Q Q Q 1.2AOMT11T316PEER-H D S S S S S S Q Q Q 1.6AOET11T302PEER-F D Q Q Q Q Q Q 0.2AOET11T304PEER-F D Q Q Q Q Q Q 0.4AOET11T305PEER-F D Q Q Q Q Q Q 0.5AOET11T308PEER-F D Q Q Q Q Q Q 0.8AOET11T310PEER-F D Q Q Q Q Q Q 1.0AOET11T312PEER-F D Q Q Q Q Q Q 1.2AOET11T316PEER-F D Q Q Q Q Q Q 1.6AOET11T320PEER-F D Q Q Q Q Q Q 2.0AOET11T324PEER-F D Q Q Q Q Q Q 2.4AOET11T330PEER-F D Q Q Q Q Q Q 3.0AOET11T332PEER-F D Q Q Q Q Q Q 3.2AOET11T302PEER-P16 D Q Q Q Q Q Q 0.2AOET11T304PEER-P16 D Q Q Q Q Q Q 0.4AOET11T305PEER-P16 S Q Q Q Q Q Q 0.5AOET11T308PEER-P16 D Q Q Q Q Q Q 0.8AOET11T310PEER-P16 S Q Q Q Q Q Q 1.0AOET11T312PEER-P16 D Q Q Q Q Q Q 1.2
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET11T302PEER-P20 D Q Q Q Q Q Q 0.2AOET11T304PEER-P20 D Q Q Q Q Q Q 0.4AOET11T305PEER-P20 S Q Q Q Q Q Q 0.5AOET11T308PEER-P20 D Q Q Q Q Q Q 0.8AOET11T310PEER-P20 S Q Q Q Q Q Q 1.0AOET11T312PEER-P20 D Q Q Q Q Q Q 1.2AOET11T302PEER-P25 D Q Q Q Q Q Q 0.2AOET11T304PEER-P25 D Q Q Q Q Q Q 0.4AOET11T305PEER-P25 S Q Q Q Q Q Q 0.5AOET11T308PEER-P25 D Q Q Q Q Q Q 0.8AOET11T310PEER-P25 S Q Q Q Q Q Q 1.0AOET11T312PEER-P25 D Q Q Q Q Q Q 1.2AOET11T302PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET11T304PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET11T305PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET11T308PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET11T310PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET11T312PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET11T316PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET11T320PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET11T324PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET11T330PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET11T332PEFR-S Q Q Q Q Q Q Q D D Q 3.2
-G: General-purpose, -H: Strong Edge, -F: Medium Finishing, -P16/-P20/-P25: High-precision Machining,
-S: Non-ferrous metals.
* -P16 is applicable to cutter diameters ø14 and ø16. -P20 is applicable to cutter diameters ø18 and ø20.
-P25 is applicable to cutter diameters ø25 and ø28.
Recommended Cutting Conditions P7
█ Insert ( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)
Fig 1 Fig 2
DM
M
LF
LSLH
DC
DM
M
LSLH
DC
LF
Rake Angle
Radial –7° to –18°
Axial 6° to 15°
16
SEC-WAVEMILL
WEZ 11000EL type
D mark: Standard stocked item
Inserts are sold separately.
█ Body (Long Type)
Cat. No.
Sto
ck Dia. Shank Head Shank Overall LengthNumber of Teeth Weight
(kg) FigDC DMM LH LS LF
WEZ 11014EL01 D 14 16 25 95 120 1 0.16 1WEZ 11016EL02 D 16 16 25 120 145 2 0.19 1WEZ 11016EL02-14 D 16 14 25 120 145 2 0.15 2WEZ 11018EL02 D 18 16 25 120 145 2 0.20 2WEZ 11020EL02 D 20 20 40 110 150 2 0.31 1WEZ 11020EL02-18 D 20 18 25 125 150 2 0.26 2WEZ 11022EL02 D 22 20 30 120 150 2 0.32 2WEZ 11025EL02 D 25 25 50 120 170 2 0.57 1WEZ 11025EL02-22 D 25 22 30 140 170 2 0.46 2WEZ 11025EL03 D 25 25 50 120 170 3 0.57 1WEZ 11028EL02 D 28 25 30 140 170 2 0.60 2WEZ 11030EL02 D 30 25 30 140 170 2 0.62 2WEZ 11032EL02 D 32 32 60 110 170 2 0.97 1WEZ 11032EL02-30 D 32 30 30 140 170 2 0.88 2WEZ 11032EL03 D 32 32 60 110 170 3 0.96 1WEZ 11035EL02 D 35 32 30 140 170 2 1.02 2WEZ 11035EL03 D 35 32 30 140 170 3 1.00 2WEZ 11040EL02 D 40 32 30 140 170 2 1.08 2WEZ 11050EL03 D 50 32 30 140 170 3 1.19 2
█ Identification Code
WEZ 11 025 E L 02 -22Series Insert
SizeDia. With
ShankLong Type
Number of Teeth
Shank Dia.
█ Spare Parts
Applicable Cutter
Flat Screw Integrated Wrench
Anti-seizure Cream
N m
WEZ11014EL01BFTX0305IP
1.5 TRDR08IP SUMI-P
WEZ11016EL02(-14)WEZ11018EL02WEZ11020EL02(-18)
BFTX0306IP
WEZ11022EL02WEZ11025EL02(-22)WEZ11025EL03WEZ11028EL02WEZ11030EL02WEZ11032EL02(-30)WEZ11032EL03WEZ11035EL02WEZ11035EL03WEZ11040EL02WEZ11050EL03
N m Recommended Tightening Torque (N·m)
Dimensions (mm)
12.8 3.6
7.5 2
0°
RE
17
SEC-WAVEMILL
WEZ 11000EL type
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT11T324PEER)Nose radius = 3.0: C1(AOMT11T330PEER)Nose radius = 3.2: C1(AOMT11T332PEER)
Standard: R1.
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT11T302PEER-G D D D D D D D Q Q D 0.2AOMT11T304PEER-G D D D D D D D Q Q D 0.4AOMT11T305PEER-G D S S S S S S Q Q S 0.5AOMT11T308PEER-G D D D D D D D Q Q D 0.8AOMT11T310PEER-G D S S S S S S Q Q S 1.0AOMT11T312PEER-G D S S S S D D Q Q S 1.2AOMT11T316PEER-G D S S S S S S Q Q 1.6AOMT11T320PEER-G D S S S S D D Q Q 2.0AOMT11T324PEER-G D S S S S S S Q Q 2.4AOMT11T330PEER-G D S S S S D D Q Q 3.0AOMT11T332PEER-G D S S S S S S Q Q 3.2AOMT11T304PEER-H D D D D D D D Q Q Q 0.4AOMT11T308PEER-H D D D D D D D Q Q Q 0.8AOMT11T312PEER-H D S S S S D D Q Q Q 1.2AOMT11T316PEER-H D S S S S S S Q Q Q 1.6AOET11T302PEER-F D Q Q Q Q Q Q 0.2AOET11T304PEER-F D Q Q Q Q Q Q 0.4AOET11T305PEER-F D Q Q Q Q Q Q 0.5AOET11T308PEER-F D Q Q Q Q Q Q 0.8AOET11T310PEER-F D Q Q Q Q Q Q 1.0AOET11T312PEER-F D Q Q Q Q Q Q 1.2AOET11T316PEER-F D Q Q Q Q Q Q 1.6AOET11T320PEER-F D Q Q Q Q Q Q 2.0AOET11T324PEER-F D Q Q Q Q Q Q 2.4AOET11T330PEER-F D Q Q Q Q Q Q 3.0AOET11T332PEER-F D Q Q Q Q Q Q 3.2AOET11T302PEER-P16 D Q Q Q Q Q Q 0.2AOET11T304PEER-P16 D Q Q Q Q Q Q 0.4AOET11T305PEER-P16 S Q Q Q Q Q Q 0.5AOET11T308PEER-P16 D Q Q Q Q Q Q 0.8AOET11T310PEER-P16 S Q Q Q Q Q Q 1.0AOET11T312PEER-P16 D Q Q Q Q Q Q 1.2
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET11T302PEER-P20 D Q Q Q Q Q Q 0.2AOET11T304PEER-P20 D Q Q Q Q Q Q 0.4AOET11T305PEER-P20 S Q Q Q Q Q Q 0.5AOET11T308PEER-P20 D Q Q Q Q Q Q 0.8AOET11T310PEER-P20 S Q Q Q Q Q Q 1.0AOET11T312PEER-P20 D Q Q Q Q Q Q 1.2AOET11T302PEER-P25 D Q Q Q Q Q Q 0.2AOET11T304PEER-P25 D Q Q Q Q Q Q 0.4AOET11T305PEER-P25 S Q Q Q Q Q Q 0.5AOET11T308PEER-P25 D Q Q Q Q Q Q 0.8AOET11T310PEER-P25 S Q Q Q Q Q Q 1.0AOET11T312PEER-P25 D Q Q Q Q Q Q 1.2AOET11T302PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET11T304PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET11T305PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET11T308PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET11T310PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET11T312PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET11T316PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET11T320PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET11T324PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET11T330PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET11T332PEFR-S Q Q Q Q Q Q Q D D Q 3.2
-G: General-purpose, -H: Strong Edge, -F: Medium Finishing, -P16/-P20/-P25: High-precision Machining,
-S: Non-ferrous metals.
* -P16 is applicable to cutter diameters ø14 and ø16. -P20 is applicable to cutter diameters ø18 and ø20.
-P25 is applicable to cutter diameters ø25 and ø28.
Recommended Cutting Conditions P7
█ Insert ( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)
Fig 2Fig 1
DM
M
LSLH
DC
LF
DM
M
LSLH
DC
LF
Rake Angle
Radial –6° to –12°
Axial 6° to 15°
18
SEC-WAVEMILL
WEZ 17000E type
D mark: Standard stocked item
█ Identification Code
WEZ 17 025 E 02 -20Series Insert
SizeDia. With
ShankNumber of Teeth
Shank Dia.
█ Body (Shank Type)
Cat. No.
Sto
ck Dia. Shank Head Shank Overall LengthNumber of Teeth Weight
(kg) FigDC DMM LH LS LF
WEZ 17025E02 D 25 25 35 85 120 2 0.38 1WEZ 17025E02-20 D 25 20 35 85 120 2 0.25 2WEZ 17028E02 D 28 25 35 85 120 2 0.40 2WEZ 17030E03 D 30 25 40 90 130 3 0.43 2WEZ 17032E02 D 32 32 40 90 130 2 0.71 1WEZ 17032E03 D 32 32 40 90 130 3 0.69 1WEZ 17032E03-25 D 32 25 40 90 130 3 0.44 2WEZ 17035E03 D 35 32 40 90 130 3 0.72 2WEZ 17040E03 D 40 32 30 105 135 3 0.81 2WEZ 17040E04 D 40 32 30 105 135 4 0.79 2WEZ 17050E03 D 50 32 30 105 135 3 0.93 2WEZ 17050E03-42 D 50 42 30 105 135 3 1.41 2WEZ 17050E05 D 50 32 30 105 135 5 0.89 2WEZ 17050E05-42 D 50 42 30 105 135 5 1.37 2WEZ 17063E04 D 63 32 30 105 135 4 1.10 2WEZ 17063E04-42 D 63 42 30 105 135 4 1.58 2WEZ 17063E06 D 63 32 30 105 135 6 1.08 2WEZ 17063E06-42 D 63 42 30 105 135 6 1.56 2WEZ 17080E07 D 80 32 30 105 135 7 1.39 2
Inserts are sold separately.
Dimensions (mm)
█ Spare Parts
Applicable Cutter
Flat Screw Integrated Wrench
Anti-seizure Cream
N m
WEZ17025E02(-20)BFTX0407IP
3.0 TRDR15IP SUMI-P
WEZ17028E02WEZ17030E03WEZ17032E02
BFTX0409IP
WEZ17032E03(-25)WEZ17035E03WEZ17040E03WEZ17040E04WEZ17050E03(-42)WEZ17050E05(-42)WEZ17063E04(-42)WEZ17063E06(-42)WEZ17080E07
N m Recommended Tightening Torque (N·m)
19.5 5.5
10
.5
20°
RE
19
SEC-WAVEMILL
WEZ 17000E type
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
-L: Low Cutting Force, -G: General-purpose, -H: Strong Edge, -F: Medium Finishing,
-P25/-P32: High-precision Machining, -S: Non-ferrous metals.
* -P25 is applicable to cutter diameters ø25 and ø28. -P32 is applicable to cutter diameters ø30, ø32 and ø35.
Recommended Cutting Conditions P7
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT170524PEER)Nose radius = 3.0: C1(AOMT170530PEER)Nose radius = 3.2: C1(AOMT170532PEER)Nose radius = 4.0: C2(AOMT170540PEER)Nose radius = 5.0: C5(AOMT170550PEER)Nose radius = 6.4: C5(AOMT170564PEER)
Standard: R1.
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT170502PEER-L D Q S Q S D D Q Q S 0.2AOMT170504PEER-L D Q D Q D D D Q Q D 0.4AOMT170508PEER-L D Q D Q D D D Q Q D 0.8AOMT170512PEER-L D Q S Q S D D Q Q S 1.2AOMT170516PEER-L D Q S Q S D D Q Q 1.6AOMT170502PEER-G D S S S S D D Q Q S 0.2AOMT170504PEER-G D D D D D D D Q Q D 0.4AOMT170505PEER-G D S S S S S S Q Q S 0.5AOMT170508PEER-G D D D D D D D Q Q D 0.8AOMT170510PEER-G D S S S S S S Q Q S 1.0AOMT170512PEER-G D S S S S D D Q Q S 1.2AOMT170516PEER-G D S S S S S S Q Q 1.6AOMT170520PEER-G D S S S S D D Q Q 2.0AOMT170524PEER-G D S S S S S S Q Q 2.4AOMT170530PEER-G D S S S S D D Q Q 3.0AOMT170532PEER-G D S S S S S S Q Q 3.2AOMT170540PEER-G D S S S S S S Q Q 4.0AOMT170550PEER-G D S S S S D D Q Q 5.0AOMT170564PEER-G D S S S S S S Q Q 6.4AOMT170504PEER-H D D D D D D D Q Q Q 0.4AOMT170508PEER-H D D D D D D D Q Q Q 0.8AOMT170512PEER-H D S S S S D D Q Q Q 1.2AOMT170516PEER-H D S S S S S S Q Q Q 1.6AOET170502PEER-F D Q Q Q Q Q Q 0.2AOET170504PEER-F D Q Q Q Q Q Q 0.4AOET170505PEER-F D Q Q Q Q Q Q 0.5AOET170508PEER-F D Q Q Q Q Q Q 0.8AOET170510PEER-F D Q Q Q Q Q Q 1.0AOET170512PEER-F D Q Q Q Q Q Q 1.2AOET170516PEER-F D Q Q Q Q Q Q 1.6AOET170520PEER-F D Q Q Q Q Q Q 2.0AOET170524PEER-F D Q Q Q Q Q Q 2.4AOET170530PEER-F D Q Q Q Q Q Q 3.0
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET170532PEER-F D Q Q Q Q Q Q 3.2AOET170540PEER-F D Q Q Q Q Q Q 4.0AOET170550PEER-F D Q Q Q Q Q Q 5.0AOET170564PEER-F D Q Q Q Q Q Q 6.4AOET170502PEER-P25 D Q Q Q Q Q Q 0.2AOET170504PEER-P25 D Q Q Q Q Q Q 0.4AOET170505PEER-P25 S Q Q Q Q Q Q 0.5AOET170508PEER-P25 D Q Q Q Q Q Q 0.8AOET170510PEER-P25 S Q Q Q Q Q Q 1.0AOET170512PEER-P25 D Q Q Q Q Q Q 1.2AOET170502PEER-P32 D Q Q Q Q Q Q 0.2AOET170504PEER-P32 D Q Q Q Q Q Q 0.4AOET170505PEER-P32 S Q Q Q Q Q Q 0.5AOET170508PEER-P32 D Q Q Q Q Q Q 0.8AOET170510PEER-P32 S Q Q Q Q Q Q 1.0AOET170512PEER-P32 D Q Q Q Q Q Q 1.2AOET170502PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET170504PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET170505PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET170508PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET170510PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET170512PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET170516PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET170520PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET170524PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET170530PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET170532PEFR-S Q Q Q Q Q Q Q D D Q 3.2AOET170540PEFR-S Q Q Q Q Q Q Q D D Q 4.0AOET170550PEFR-S Q Q Q Q Q Q Q D D Q 5.0AOET170564PEFR-S Q Q Q Q Q Q Q D D Q 6.4
█ Insert ( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)
Fig 2Fig 1
DM
M
LSLH
DC
LF
DM
M
LSLH
DC
LF
Rake Angle
Radial –6° to –12°
Axial 6° to 15°
20
SEC-WAVEMILL
WEZ 17000EL type
D mark: Standard stocked item
█ Identification Code
WEZ 17 032 E L 02 -30Series Insert
SizeDia. With
ShankLong Type
Number of Teeth
Shank Dia.
█ Body (Long Type)
Cat. No.
Sto
ck Dia. Shank Head Shank Overall LengthNumber of Teeth Weight
(kg) FigDC DMM LH LS LF
WEZ 17025EL02 D 25 25 50 120 170 2 0.55 1WEZ 17028EL02 D 28 25 50 120 170 2 0.57 2WEZ 17030EL02 D 30 25 50 120 170 2 0.59 2WEZ 17032EL02 D 32 32 60 110 170 2 0.94 1WEZ 17032EL02-30 D 32 30 50 120 170 2 0.85 2WEZ 17032EL03 D 32 32 60 110 170 3 0.92 1WEZ 17035EL02 D 35 32 50 120 170 2 0.98 2WEZ 17040EL02 D 40 32 50 120 170 2 1.09 2WEZ 17040EL03 D 40 32 50 120 170 3 1.08 2WEZ 17040EL04 D 40 32 50 120 170 4 1.05 2WEZ 17050EL03 D 50 32 50 120 170 3 1.29 2WEZ 17050EL03-42 D 50 42 50 120 170 3 1.83 2WEZ 17050EL05 D 50 32 50 120 170 5 1.25 2WEZ 17050EL05-42 D 50 42 50 120 170 5 1.79 2WEZ 17063EL04 D 63 32 50 120 170 4 1.61 2WEZ 17063EL04-42 D 63 42 50 120 170 4 2.16 2WEZ 17063EL06 D 63 32 50 120 170 6 1.58 2WEZ 17063EL06-42 D 63 42 50 120 170 6 2.13 2
Inserts are sold separately.
Dimensions (mm)
█ Spare Parts
Applicable Cutter
Flat Screw Integrated Wrench
Anti-seizure Cream
N m
WEZ17025EL02BFTX0407IP
3.0 TRDR15IP SUMI-P
WEZ17028EL02WEZ17030EL02WEZ17032EL02(-30)
BFTX0409IP
WEZ17032EL03WEZ17035EL02WEZ17040EL02WEZ17040EL03WEZ17040EL04WEZ17050EL03(-42)WEZ17050EL05(-42)WEZ17063EL04(-42)WEZ17063EL06(-42)
N m Recommended Tightening Torque (N·m)
19.5 5.5
10
.5
20°
RE
21
SEC-WAVEMILL
WEZ 17000EL type
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
-L: Low Cutting Force, -G: General-purpose, -H: Strong Edge, -F: Medium Finishing,
-P25/-P32: High-precision Machining, -S: Non-ferrous metals.
* -P25 is applicable to cutter diameters ø25 and ø28. -P32 is applicable to cutter diameters ø30, ø32 and ø35.
Recommended Cutting Conditions P7
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT170524PEER)Nose radius = 3.0: C1(AOMT170530PEER)Nose radius = 3.2: C1(AOMT170532PEER)Nose radius = 4.0: C2(AOMT170540PEER)Nose radius = 5.0: C5(AOMT170550PEER)Nose radius = 6.4: C5(AOMT170564PEER)
Standard: R1.
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT170502PEER-L D Q S Q S D D Q Q S 0.2AOMT170504PEER-L D Q D Q D D D Q Q D 0.4AOMT170508PEER-L D Q D Q D D D Q Q D 0.8AOMT170512PEER-L D Q S Q S D D Q Q S 1.2AOMT170516PEER-L D Q S Q S D D Q Q 1.6AOMT170502PEER-G D S S S S D D Q Q S 0.2AOMT170504PEER-G D D D D D D D Q Q D 0.4AOMT170505PEER-G D S S S S S S Q Q S 0.5AOMT170508PEER-G D D D D D D D Q Q D 0.8AOMT170510PEER-G D S S S S S S Q Q S 1.0AOMT170512PEER-G D S S S S D D Q Q S 1.2AOMT170516PEER-G D S S S S S S Q Q 1.6AOMT170520PEER-G D S S S S D D Q Q 2.0AOMT170524PEER-G D S S S S S S Q Q 2.4AOMT170530PEER-G D S S S S D D Q Q 3.0AOMT170532PEER-G D S S S S S S Q Q 3.2AOMT170540PEER-G D S S S S S S Q Q 4.0AOMT170550PEER-G D S S S S D D Q Q 5.0AOMT170564PEER-G D S S S S S S Q Q 6.4AOMT170504PEER-H D D D D D D D Q Q Q 0.4AOMT170508PEER-H D D D D D D D Q Q Q 0.8AOMT170512PEER-H D S S S S D D Q Q Q 1.2AOMT170516PEER-H D S S S S S S Q Q Q 1.6AOET170502PEER-F D Q Q Q Q Q Q 0.2AOET170504PEER-F D Q Q Q Q Q Q 0.4AOET170505PEER-F D Q Q Q Q Q Q 0.5AOET170508PEER-F D Q Q Q Q Q Q 0.8AOET170510PEER-F D Q Q Q Q Q Q 1.0AOET170512PEER-F D Q Q Q Q Q Q 1.2AOET170516PEER-F D Q Q Q Q Q Q 1.6AOET170520PEER-F D Q Q Q Q Q Q 2.0AOET170524PEER-F D Q Q Q Q Q Q 2.4AOET170530PEER-F D Q Q Q Q Q Q 3.0
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET170532PEER-F D Q Q Q Q Q Q 3.2AOET170540PEER-F D Q Q Q Q Q Q 4.0AOET170550PEER-F D Q Q Q Q Q Q 5.0AOET170564PEER-F D Q Q Q Q Q Q 6.4AOET170502PEER-P25 D Q Q Q Q Q Q 0.2AOET170504PEER-P25 D Q Q Q Q Q Q 0.4AOET170505PEER-P25 S Q Q Q Q Q Q 0.5AOET170508PEER-P25 D Q Q Q Q Q Q 0.8AOET170510PEER-P25 S Q Q Q Q Q Q 1.0AOET170512PEER-P25 D Q Q Q Q Q Q 1.2AOET170502PEER-P32 D Q Q Q Q Q Q 0.2AOET170504PEER-P32 D Q Q Q Q Q Q 0.4AOET170505PEER-P32 S Q Q Q Q Q Q 0.5AOET170508PEER-P32 D Q Q Q Q Q Q 0.8AOET170510PEER-P32 S Q Q Q Q Q Q 1.0AOET170512PEER-P32 D Q Q Q Q Q Q 1.2AOET170502PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET170504PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET170505PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET170508PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET170510PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET170512PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET170516PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET170520PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET170524PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET170530PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET170532PEFR-S Q Q Q Q Q Q Q D D Q 3.2AOET170540PEFR-S Q Q Q Q Q Q Q D D Q 4.0AOET170550PEFR-S Q Q Q Q Q Q Q D D Q 5.0AOET170564PEFR-S Q Q Q Q Q Q Q D D Q 6.4
█ Insert ( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)
H
DC
ON
LF
OAL
LS
L11 CRKS
DC
LS2
Rake Angle
Radial –7° to –18°
Axial 6° to 15°
22
SEC-WAVEMILL
WEZ 11000M type Modular Tools
SEC-
Expansion
D mark: Standard stocked item D mark: Standard stocked item (expanded item)
Inserts are sold separately. Arbor P26
█ Head
Cat. No.
Sto
ck Dia. Mounting Dia. Screw Overall
LengthEffective Length Length Shank Chamfer Width Number
of TeethWeight
(kg)DC DCON CRKS OAL LF LS2 LS L11 H
WEZ 11016M08Z2 D 16 8.5 M8 42 25 5 17 8 13 2 0.03WEZ 11018M08Z2 D 18 8.5 M8 42 25 5 17 8 13 2 0.03WEZ 11020M10Z2 D 20 10.5 M10 49 30 5 19 8 15 2 0.06WEZ 11020M10Z3 D 20 10.5 M10 49 30 5 19 8 15 3 0.05WEZ 11022M10Z3 D 22 10.5 M10 49 30 5 19 8 15 3 0.06WEZ 11025M12Z2 D 25 12.5 M12 56 35 5 21 10 19 2 0.11WEZ 11025M12Z3 D 25 12.5 M12 56 35 5 21 10 19 3 0.10WEZ 11025M12Z4 D 25 12.5 M12 56 35 5 21 10 19 4 0.10WEZ 11026M12Z4 D 26 12.5 M12 56 35 5 21 10 19 4 0.10WEZ 11026M12Z5 D 26 12.5 M12 56 35 5 21 10 19 5 0.09WEZ 11028M12Z4 D 28 12.5 M12 56 35 5 21 10 19 4 0.11WEZ 11028M12Z5 D 28 12.5 M12 56 35 5 21 10 19 5 0.10WEZ 11030M16Z2 D 30 17 M16 63 40 5 23 10 24 2 0.20WEZ 11030M16Z4 D 30 17 M16 63 40 5 23 10 24 4 0.19WEZ 11030M16Z5 D 30 17 M16 63 40 5 23 10 24 5 0.17WEZ 11032M16Z2 D 32 17 M16 63 40 5 23 10 24 2 0.22WEZ 11032M16Z3 D 32 17 M16 63 40 5 23 10 24 3 0.20WEZ 11032M16Z4 D 32 17 M16 63 40 5 23 10 24 4 0.20WEZ 11032M16Z5 D 32 17 M16 63 40 5 23 10 24 5 0.19WEZ 11035M16Z2 D 35 17 M16 63 40 5 23 10 24 2 0.24WEZ 11035M16Z5 D 35 17 M16 63 40 5 23 10 24 5 0.22WEZ 11040M16Z2 D 40 17 M16 63 40 5 23 10 24 2 0.28WEZ 11040M16Z4 D 40 17 M16 63 40 5 23 10 24 4 0.26WEZ 11040M16Z5 D 40 17 M16 63 40 5 23 10 24 5 0.26WEZ 11040M16Z6 D 40 17 M16 63 40 5 23 10 24 6 0.25
█ Identification Code
WEZ 11 016 M08 Z2Series Insert
SizeDia. Mounting
Screw SizeNumber of Teeth
Dimensions (mm)
█ Spare Parts
Applicable Endmills
Flat Screw Integrated Wrench
Anti-seizure Cream
N m
WEZ11016M08Z2, WEZ11018M08Z2 BFTX0305IP1.5 TRDR08IP SUMI-P
WEZ11020M10Z2 to WEZ11040M16Z6 BFTX0306IP
N m Recommended Tightening Torque (N·m)
12.8 3.6
7.5 2
0°
RE
23
SEC-WAVEMILL
WEZ 11000M type Modular Tools
SEC-
Expansion
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT11T324PEER)Nose radius = 3.0: C1(AOMT11T330PEER)Nose radius = 3.2: C1(AOMT11T332PEER)
Standard: R1.
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT11T302PEER-G D D D D D D D Q Q D 0.2AOMT11T304PEER-G D D D D D D D Q Q D 0.4AOMT11T305PEER-G D S S S S S S Q Q S 0.5AOMT11T308PEER-G D D D D D D D Q Q D 0.8AOMT11T310PEER-G D S S S S S S Q Q S 1.0AOMT11T312PEER-G D S S S S D D Q Q S 1.2AOMT11T316PEER-G D S S S S S S Q Q 1.6AOMT11T320PEER-G D S S S S D D Q Q 2.0AOMT11T324PEER-G D S S S S S S Q Q 2.4AOMT11T330PEER-G D S S S S D D Q Q 3.0AOMT11T332PEER-G D S S S S S S Q Q 3.2AOMT11T304PEER-H D D D D D D D Q Q Q 0.4AOMT11T308PEER-H D D D D D D D Q Q Q 0.8AOMT11T312PEER-H D S S S S D D Q Q Q 1.2AOMT11T316PEER-H D S S S S S S Q Q Q 1.6AOET11T302PEER-F D Q Q Q Q Q Q 0.2AOET11T304PEER-F D Q Q Q Q Q Q 0.4AOET11T305PEER-F D Q Q Q Q Q Q 0.5AOET11T308PEER-F D Q Q Q Q Q Q 0.8AOET11T310PEER-F D Q Q Q Q Q Q 1.0AOET11T312PEER-F D Q Q Q Q Q Q 1.2AOET11T316PEER-F D Q Q Q Q Q Q 1.6AOET11T320PEER-F D Q Q Q Q Q Q 2.0AOET11T324PEER-F D Q Q Q Q Q Q 2.4AOET11T330PEER-F D Q Q Q Q Q Q 3.0AOET11T332PEER-F D Q Q Q Q Q Q 3.2AOET11T302PEER-P16 D Q Q Q Q Q Q 0.2AOET11T304PEER-P16 D Q Q Q Q Q Q 0.4AOET11T305PEER-P16 S Q Q Q Q Q Q 0.5AOET11T308PEER-P16 D Q Q Q Q Q Q 0.8AOET11T310PEER-P16 S Q Q Q Q Q Q 1.0AOET11T312PEER-P16 D Q Q Q Q Q Q 1.2
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET11T302PEER-P20 D Q Q Q Q Q Q 0.2AOET11T304PEER-P20 D Q Q Q Q Q Q 0.4AOET11T305PEER-P20 S Q Q Q Q Q Q 0.5AOET11T308PEER-P20 D Q Q Q Q Q Q 0.8AOET11T310PEER-P20 S Q Q Q Q Q Q 1.0AOET11T312PEER-P20 D Q Q Q Q Q Q 1.2AOET11T302PEER-P25 D Q Q Q Q Q Q 0.2AOET11T304PEER-P25 D Q Q Q Q Q Q 0.4AOET11T305PEER-P25 S Q Q Q Q Q Q 0.5AOET11T308PEER-P25 D Q Q Q Q Q Q 0.8AOET11T310PEER-P25 S Q Q Q Q Q Q 1.0AOET11T312PEER-P25 D Q Q Q Q Q Q 1.2AOET11T302PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET11T304PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET11T305PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET11T308PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET11T310PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET11T312PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET11T316PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET11T320PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET11T324PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET11T330PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET11T332PEFR-S Q Q Q Q Q Q Q D D Q 3.2
-G: General-purpose, -H: Strong Edge, -F: Medium Finishing, -P16/-P20/-P25: High-precision Machining,
-S: Non-ferrous metals.
* -P16 is applicable to cutter diameters ø14 and ø16. -P20 is applicable to cutter diameters ø18 and ø20.
-P25 is applicable to cutter diameters ø25 and ø28.
Recommended Cutting Conditions P7
█ Insert ( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)
DC
H
DC
ON
LF
OAL
LS
CRKS
LS2
L11
Rake Angle
Radial –6° to –12°
Axial 6° to 15°
24
SEC-WAVEMILL
WEZ 17000M type Modular Tools
SEC-
Expansion
D mark: Standard stocked item D mark: Standard stocked item (expanded item)
Inserts are sold separately. Arbor P26
█ Head
Cat. No.
Sto
ck Dia. Mounting Dia. Screw Overall
LengthEffective Length Length Shank Chamfer Width Number
of TeethWeight
(kg)DC DCON CRKS OAL LF LS2 LS L11 H
WEZ 17025M12Z2 D 25 12.5 M12 56 35 5 21 10 19 2 0.08WEZ 17025M12Z3 D 25 12.5 M12 56 35 5 21 10 19 3 0.07WEZ 17028M12Z2 D 28 12.5 M12 56 35 5 21 10 19 2 0.10WEZ 17030M16Z2 D 30 17 M16 63 40 5 23 10 24 2 0.17WEZ 17030M16Z3 D 30 17 M16 63 40 5 23 10 24 3 0.15WEZ 17032M16Z2 D 32 17 M16 63 40 5 23 10 24 2 0.19WEZ 17032M16Z3 D 32 17 M16 63 40 5 23 10 24 3 0.16WEZ 17032M16Z4 D 32 17 M16 63 40 5 23 10 24 4 0.14WEZ 17035M16Z2 D 35 17 M16 63 40 5 23 10 24 2 0.21WEZ 17035M16Z3 D 35 17 M16 63 40 5 23 10 24 3 0.19WEZ 17040M16Z2 D 40 17 M16 63 40 5 23 10 24 2 0.25WEZ 17040M16Z3 D 40 17 M16 63 40 5 23 10 24 3 0.23WEZ 17040M16Z4 D 40 17 M16 63 40 5 23 10 24 4 0.21
█ Identification Code
WEZ 17 025 M12 Z2Series Insert
SizeDia. Mounting
Screw SizeNumber of Teeth
Dimensions (mm)
█ Spare Parts
Applicable Endmills
Flat Screw Integrated Wrench
Anti-seizure Cream
N m
WEZ17025M12Z2 to WEZ17030M16Z3 BFTX0407IP3.0 TRDR15IP SUMI-P
WEZ17032M16Z2 to WEZ17040M16Z4 BFTX0409IP
N m Recommended Tightening Torque (N·m)
19.5 5.5
10
.5
20°
RE
25
SEC-WAVEMILL
WEZ 17000M type Modular Tools
SEC-
Expansion
D mark: Standard stocked item D mark: Standard stocked item (expanded item) S mark: Planned stock Blank: Made-to-order item Q mark: Not available
-L: Low Cutting Force, -G: General-purpose, -H: Strong Edge, -F: Medium Finishing,
-P25/-P32: High-precision Machining, -S: Non-ferrous metals.
* -P25 is applicable to cutter diameters ø25 and ø28. -P32 is applicable to cutter diameters ø30, ø32 and ø35.
Recommended Cutting Conditions P7
* When mounting inserts with nose radius of 2.4 or above, modification of the body is required.
Modify this portion.Reworking guidelinesNose radius = 2.4: C0.5(AOMT170524PEER)Nose radius = 3.0: C1(AOMT170530PEER)Nose radius = 3.2: C1(AOMT170532PEER)Nose radius = 4.0: C2(AOMT170540PEER)Nose radius = 5.0: C5(AOMT170550PEER)Nose radius = 6.4: C5(AOMT170564PEER)
Standard: R1.
Precautions for Mounting Inserts
(1) Clean the mounting seat surface and contact parts.
(2) While pressing the insert firmly against the seat surface, tighten the screws with the included wrench.
(3) Apply Anti-seizure Cream to the screws and tighten at the recommended torque.
(4) After tightening, check that there are no gaps on the seat surface.
Gap
Gap
Insert
Wrench
Body
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOMT170502PEER-L D Q S Q S D D Q Q S 0.2AOMT170504PEER-L D Q D Q D D D Q Q D 0.4AOMT170508PEER-L D Q D Q D D D Q Q D 0.8AOMT170512PEER-L D Q S Q S D D Q Q S 1.2AOMT170516PEER-L D Q S Q S D D Q Q 1.6AOMT170502PEER-G D S S S S D D Q Q S 0.2AOMT170504PEER-G D D D D D D D Q Q D 0.4AOMT170505PEER-G D S S S S S S Q Q S 0.5AOMT170508PEER-G D D D D D D D Q Q D 0.8AOMT170510PEER-G D S S S S S S Q Q S 1.0AOMT170512PEER-G D S S S S D D Q Q S 1.2AOMT170516PEER-G D S S S S S S Q Q 1.6AOMT170520PEER-G D S S S S D D Q Q 2.0AOMT170524PEER-G D S S S S S S Q Q 2.4AOMT170530PEER-G D S S S S D D Q Q 3.0AOMT170532PEER-G D S S S S S S Q Q 3.2AOMT170540PEER-G D S S S S S S Q Q 4.0AOMT170550PEER-G D S S S S D D Q Q 5.0AOMT170564PEER-G D S S S S S S Q Q 6.4AOMT170504PEER-H D D D D D D D Q Q Q 0.4AOMT170508PEER-H D D D D D D D Q Q Q 0.8AOMT170512PEER-H D S S S S D D Q Q Q 1.2AOMT170516PEER-H D S S S S S S Q Q Q 1.6AOET170502PEER-F D Q Q Q Q Q Q 0.2AOET170504PEER-F D Q Q Q Q Q Q 0.4AOET170505PEER-F D Q Q Q Q Q Q 0.5AOET170508PEER-F D Q Q Q Q Q Q 0.8AOET170510PEER-F D Q Q Q Q Q Q 1.0AOET170512PEER-F D Q Q Q Q Q Q 1.2AOET170516PEER-F D Q Q Q Q Q Q 1.6AOET170520PEER-F D Q Q Q Q Q Q 2.0AOET170524PEER-F D Q Q Q Q Q Q 2.4AOET170530PEER-F D Q Q Q Q Q Q 3.0
ApplicationsHigh-speed/Light P K N PGeneral-purpose P K N N
Roughing P K Dimensions (mm)
Cat. No.
AC
U25
00
AC
P20
00
AC
P30
00
AC
K20
00
AC
K30
00
AC
M20
0
AC
M30
0
H20
DL2
000
T250
0A Nose Radius
RE
AOET170532PEER-F D Q Q Q Q Q Q 3.2AOET170540PEER-F D Q Q Q Q Q Q 4.0AOET170550PEER-F D Q Q Q Q Q Q 5.0AOET170564PEER-F D Q Q Q Q Q Q 6.4AOET170502PEER-P25 D Q Q Q Q Q Q 0.2AOET170504PEER-P25 D Q Q Q Q Q Q 0.4AOET170505PEER-P25 S Q Q Q Q Q Q 0.5AOET170508PEER-P25 D Q Q Q Q Q Q 0.8AOET170510PEER-P25 S Q Q Q Q Q Q 1.0AOET170512PEER-P25 D Q Q Q Q Q Q 1.2AOET170502PEER-P32 D Q Q Q Q Q Q 0.2AOET170504PEER-P32 D Q Q Q Q Q Q 0.4AOET170505PEER-P32 S Q Q Q Q Q Q 0.5AOET170508PEER-P32 D Q Q Q Q Q Q 0.8AOET170510PEER-P32 S Q Q Q Q Q Q 1.0AOET170512PEER-P32 D Q Q Q Q Q Q 1.2AOET170502PEFR-S Q Q Q Q Q Q Q D D Q 0.2AOET170504PEFR-S Q Q Q Q Q Q Q D D Q 0.4AOET170505PEFR-S Q Q Q Q Q Q Q D D Q 0.5AOET170508PEFR-S Q Q Q Q Q Q Q D D Q 0.8AOET170510PEFR-S Q Q Q Q Q Q Q D D Q 1.0AOET170512PEFR-S Q Q Q Q Q Q Q D D Q 1.2AOET170516PEFR-S Q Q Q Q Q Q Q D D Q 1.6AOET170520PEFR-S Q Q Q Q Q Q Q D D Q 2.0AOET170524PEFR-S Q Q Q Q Q Q Q D D Q 2.4AOET170530PEFR-S Q Q Q Q Q Q Q D D Q 3.0AOET170532PEFR-S Q Q Q Q Q Q Q D D Q 3.2AOET170540PEFR-S Q Q Q Q Q Q Q D D Q 4.0AOET170550PEFR-S Q Q Q Q Q Q Q D D Q 5.0AOET170564PEFR-S Q Q Q Q Q Q Q D D Q 6.4
█ Insert ( P Steel M Stainless Steel K Cast Iron N Non-Ferrous Metal S Exotic Alloy H Hardened Steel █ Coated Carbide █ Carbide █ DLC █ Cermet)
DM
M h
7
CRKS
DC
B
LF2
L4
L5
DC
B
BD
ø46
L7
LBX
LF
L6
CRKS
26
SEC-Modular Tools
Special Arbor
█ BBT - 30 Integrated Arbor
Cat. No. StockScrew Bore Dia. External
Dia.Body
Overhang Length Thread Depth Overhang Coolant
HoleCRKS DCB BD L6 LBX L7 LF*1
BBT30-M8-50 D M8 8.5 15.9 73 50 18 98 yesBBT30-M10-45 D M10 10.5 19.9 68 45 20 98 yesBBT30-M12-40 D M12 12.5 24.9 63 40 22 98 yesBBT30-M16-35 D M16 17 31.9 58 35 24 98 yes
*1 Overhang length for LF is with head mounted. * Can also be used with BT30 spindle machines.
█ BBT - Integrated Type Special Arbors for SEC-Modular Tools
█ SEC-Modular Tools Special Arbors (Carbide Arbors/Steel Arbors)
Carbide Arbor
Steel Arbor
█ Carbide Arbors
Cat. No.
Sto
ck Screw Bore Dia.
ShankDia.
Overall Length Depth Thread
DepthSet
Length
CRKS DCB DMM LF2 L4 L5 LF*2
MA15M08L120C D M8 8.5 15 120 10 18 145MA15M08L160C D M8 8.5 15 160 10 18 185MA16M08L120C D M8 8.5 16 120 10 18 145MA16M08L160C D M8 8.5 16 160 10 18 185MA18M10L150C D M10 10.5 18 150 10 20 180MA18M10L200C D M10 10.5 18 200 10 20 230MA20M10L150C D M10 10.5 20 150 10 20 180MA20M10L200C D M10 10.5 20 200 10 20 230MA23M12L200C D M12 12.5 23 200 10 22 235MA23M12L250C D M12 12.5 23 250 10 22 285MA25M12L200C D M12 12.5 25 200 10 22 235MA25M12L250C D M12 12.5 25 250 10 22 285MA28M16L200C D M16 17.0 28 200 10 24 240MA28M16L300C D M16 17.0 28 300 10 24 340MA32M16L200C D M16 17.0 32 200 10 24 240MA32M16L300C D M16 17.0 32 300 10 24 340
Dimensions (mm) █ Steel Arbors
Cat. No.
Sto
ck Screw Bore Dia.
ShankDia.
Overall Length Depth Thread
DepthSet
Length
CRKS DCB DMM LF2 L4 L5 LF*2
MA16M08L120S D M8 8.5 16 120 10 18 145MA20M10L150S D M10 10.5 20 150 10 20 180MA25M12L200S D M12 12.5 25 200 10 22 235MA32M16L200S D M16 17.0 32 200 10 24 240
Dimensions (mm)
█ Identification Code
Arbor Materials
MA 15 M08 L120 CSeries Shank
Dia.Mounting
Screw SizeArbor Overall
Length C: CarbideS: Steel(
D Set Length (*2)
LF (Length of Head + Arbor)
* Take care when tightening the head.
· When mounting the head to an arbor, follow the standard tightening torque in the table below.
· Check the mounting screw size for the head and arbor beforehand.· Refer to the █ Head Cat. No. chart on P22, P24 to select the tool size
in the table below.
Screw SizeRegulated
Tightening Torque(N·m)
Tool Dimensions
L11 H
M8 23 8 13
M10 46 8 15
M12 60 10 19
M16 80 10 24
Dimensions (mm)
D mark: Standard stocked item
27
SEC-WAVEMILL
WEZ series
Steel S40C Hub Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ17025E02 Double-Sided, 4 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 25 25Number of Teeth 2 2vc (m/min) 120 120vf (mm/min) 300 300fz (mm/t) 0.066 0.066ap(mm) 9 9ae (mm) 5 5Coolant Wet Wet
Results
The high chattering sound typical of thin workpieces is gone, and stable machining enables longer tool life
Die Steel SKD11 (Soft Steel) Mold Parts Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ11020E03 Double-Sided, 4 Corners
Grade ACU2500 QChipbreaker H QCutter Dia. (mm) 20 20Number of Teeth 3 3vc (m/min) 145 190vf (mm/min) 1,035 3,000fz (mm/t) 0.15 0.35ap(mm) 6.0 0.5ae (mm) 6.0 8.4Coolant Dry Dry
Results3x efficiency in helical milling. Improved surface quality integrates processes
Steel SM490A Machine Component Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ17032EL03 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 32 32Number of Teeth 3 2vc (m/min) 150 150vf (mm/min) 671 447fz (mm/t) 0.15 0.15ap(mm) 1.25 1.25ae (mm) 32 32Coolant Wet Wet
Results Efficiency improved 1.5x, quiet and stable machining
Steel S50C Machine Component Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ17032E03 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 32 32Number of Teeth 3 3vc (m/min) 75 75vf (mm/min) 225 225fz (mm/t) 0.1 0.1ap(mm) 4 4ae (mm) 22 22Coolant Wet Wet
Results
Drastically reduced cutting edge failure with the same outputContinuous use possible, longer tool life
█ Application Example
Alloy Tool Steel SKT4 (45HRC) Machine Components Sumitomo Comp’sVertical Machining Centre HSK-A63
Tool WEZ11022E03 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 22 22Number of Teeth 3 3vc (m/min) 50 30vf (mm/min) 217 130fz (mm/t) 0.1 0.1ap(mm) 3 3ae (mm) 22 22Coolant Wet Wet
Results
Improvements of 1.7x efficiency and 2.5x tool life Stable machining of 45HRC hardened steel is possible
Steel S50C Mold Component Sumitomo Comp’sRam-type Milling Machine BT40
Tool WEZ11022E03 Single-Sided, 2 Corners
Grade T2500A QChipbreaker G QCutter Dia. (mm) 22 22Number of Teeth 3 3vc (m/min) 83 75vf (mm/min) 320 290fz (mm/t) 0.09 0.09ap(mm) 2.5 2.5ae (mm) 10 10Coolant Q Q
Results
Improved machined surface quality and machining efficiency with cermet grades
Steel S45C Machine Component Sumitomo Comp’sMulti-task machine Tool WEZ11025E03 Single-Sided,
2 CornersGrade ACU2500 QChipbreaker G QCutter Dia. (mm) 25 25Number of Teeth 3 3vc (m/min) 157 157vf (mm/min) 300 300fz (mm/t) 0.05 0.05ap(mm) 5 5ae (mm) 3.5 3.5Coolant Q Q
Results
Thin-walled machining with excellent wall accuracy and no chattering, even on a low rigidity multi-task machine
Steel S50C Machine Component Sumitomo Comp’s5-axis Control Vertical Machining Centre HSK-A100
Tool WEZ11020M10Z3 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 20 20Number of Teeth 3 3vc (m/min) 72 72vf (mm/min) 4,000 4,000fz (mm/t) 0.2 0.2ap(mm) 0.7 0.7ae (mm) 20 20Coolant Dry Dry
Results
Stability without chatter even in groove milling with overhang 120 mm (L/D=6)
Modular Tools
SEC-
28
SEC-WAVEMILL
WEZ series
Stainless Steel SUS304 Machine Components Sumitomo Comp’sMulti-task machine Tool WEZ11022E03 Single-Sided,
2 CornersGrade ACU2500 QChipbreaker G QCutter Dia. (mm) 22 22Number of Teeth 3 3vc (m/min) 120 120vf (mm/min) 1,562 1,562fz (mm/t) 0.3 0.3ap(mm) 2 2ae (mm) 22 22Coolant Wet Wet
Results
As a result of improved quality visually, the finishing process can be omitted, achieving process integration
Stainless Steel SUS Machine Component Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ11032E03 Single-Sided, 2 Corners
Grade T2500A QChipbreaker G QCutter Dia. (mm) 32 32Number of Teeth 3 3vc (m/min) 154 154vf (mm/min) 530 400fz (mm/t) 0.12 0.09ap(mm) 0.5 0.5ae (mm) 20 20Coolant Q Q
ResultsImproved machined surface quality and machining efficiency with cermet grades
Stainless Steel SUS304 Machine Components Sumitomo Comp’sVertical Machining Centre BT30
Tool WEZ11020E03 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 20 20Number of Teeth 3 3vc (m/min) 150 150vf (mm/min) 860 860fz (mm/t) 0.12 0.12ap(mm) 2 2ae (mm) 8 8Coolant Wet Wet
ResultsGood surface finish and edge sharpness even with long-rigidity BT30 setup
Stainless Steel SUS304 Semiconductor Device Sumitomo Comp’sHorizontal Machining Centre: BT50
Tool WEZ17050RS05 Double-Sided, 4 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 50 50Number of Teeth 5 5vc (m/min) 80 80vf (mm/min) 320 320fz (mm/t) 0.13 0.13ap(mm) 0.2 0.2ae (mm) 40 40Coolant Wet Wet
Results
Improved surface finish quality and reduced burrs, cutting post-processing time by 50%
Stainless Steel SUS316L Machine Components Sumitomo QVertical Machining Centre BT40
Tool WEZ17035E03 Q
Grade ACU2500 QChipbreaker P QCutter Dia. (mm) 35 QNumber of Teeth 3 Qvc (m/min) 100 Qvf (mm/min) 410 Qfz (mm/t) 0.15 Qap(mm) 9 Qae (mm) 0.1 QCoolant Wet Q
ResultsGood wall surface accuracy, applicable to finishing (ae = 0.1mm)
Stainless Steel SUS304 Machine Components Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ11028E04 Q
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 28 28Number of Teeth 4 4vc (m/min) 150 150vf (mm/min) 1,350 1,350fz (mm/t) 0.2 0.2ap(mm) 2 2ae (mm) 10 10Coolant Dry Dry
Results Longer tool life Stable machining achieved
Stainless Cast Steel SCS13 Machine Components Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ11040E04 Single-Sided, 4 Corners
Grade ACM300 QChipbreaker G QCutter Dia. (mm) 40 40Number of Teeth 4 4vc (m/min) 80 80vf (mm/min) 254 254fz (mm/t) 0.1 0.1ap(mm) 1 1ae (mm) 40 40Coolant Q Q
ResultsLonger tool life without chipping or fracture, even on mill-scaled work
Stainless Steel SUS304 Machine Components Sumitomo Comp’sVertical Machining Centre BT30
Tool WEZ11020E03 H’s (High Speed Steel) Roughing Endmill
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 20 20Number of Teeth 3 4vc (m/min) 150 60vf (mm/min) 860 340fz (mm/t) 0.12 0.09ap(mm) 2 2ae (mm) 8 8Coolant Q Q
Results
Longer tool life with reduced machining time as compared to using HSS endmills
29
SEC-WAVEMILL
WEZ series
Ductile Cast Iron FCD450 Straight Rail Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ17040EL03 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 40 40Number of Teeth 3 3vc (m/min) 130 130vf (mm/min) 465 465fz (mm/t) 0.15 0.15ap(mm) 8 6ae (mm) 40 40Coolant Dry Dry
Results1.3x better efficiency with reduced vibration during machining
Grey Cast Iron FC300 Table Sumitomo Comp’s5-axis Control Vertical Machining Centre HSK-A63
Tool WEZ11040E06 Q
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 40 40Number of Teeth 6 6vc (m/min) 200 200vf (mm/min) 1,300 1,300fz (mm/t) 0.135 0.135ap(mm) 2 2ae (mm) 20 20Coolant Wet Wet
ResultsStable machining possible even for thin workpieces or low-rigidity machines
Gray Cast Iron FC250 Mounting Base Frame Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ11032E05 Single-Sided, 2 Corners
Grade ACK3000 QChipbreaker G QCutter Dia. (mm) 32 32Number of Teeth 5 4vc (m/min) 220 220vf (mm/min) 1100 900fz (mm/t) 0.1 0.1ap(mm) 2 2ae (mm) 20 20Coolant Dry Dry
ResultsEfficiency improved Even thin portions can be machined without chatter
Grey Cast Iron FC250 Machine Component Sumitomo Comp’sHorizontal Machining Centre: BT50
Tool WEZ11050RS07 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 50 50Number of Teeth 7 5vc (m/min) 180 180vf (mm/min) 805 574fz (mm/t) 0.1 0.1ap(mm) 0.3 0.3ae (mm) 10 10Coolant Wet Wet
Results
Quiet machining and increased machining efficiency Good surface finish quality and flatness
Cast Steel for Welded Structure Product SCW480 Press Housing Sumitomo Comp’sDouble Column 5-axis Machining Centre BT50
Tool WEZ17160R08 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 60 60Number of Teeth 8 8vc (m/min) 150.7 150.7vf (mm/min) 500 500fz (mm/t) 0.208 0.208ap(mm) 7 7ae (mm) 75 75Coolant Q Q
ResultsReduces chipping on large workpieces, enabling stable machining
Ductile Cast Iron FCD450 Machine Components Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ11050E05 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker F QCutter Dia. (mm) 50 50Number of Teeth 5 5vc (m/min) 157 94vf (mm/min) 300 270fz (mm/t) 0.06 0.09ap(mm) 1.2 1.2ae (mm) 10 10Coolant Wet Wet
Results
Superior sharpness ensures chatter control and increased efficiency, enables finishing as well
Grey Cast Iron FC300 Machine Component Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ17063RS06 Single-Sided, 2 Corners
Grade ACK3000 QChipbreaker G QCutter Dia. (mm) 63 63Number of Teeth 6 4vc (m/min) 150 175vf (mm/min) 377 254fz (mm/t) 0.08 0.07ap(mm) 3.5 3.5ae (mm) 50 50Coolant Wet Wet
ResultsEfficiency improved 1.5x in helical milling Tool life doubled
Grey Cast Iron FC250 Railway Component Sumitomo Comp’sVertical Machining Centre
Tool WEZ11040M16Z6 Single-Sided, 4 Corners
Grade ACK3000 QChipbreaker G QCutter Dia. (mm) 40 40Number of Teeth 6 3vc (m/min) 37 48vf (mm/min) 707 344fz (mm/t) 0.4 0.3ap(mm) 2.5 x 1 pass + 1 1.5 x 2 passes + 0.5ae (mm) Q QCoolant Wet Wet
Results
Increased cutting edge sharpness enables stable machining with efficiency improved 4.5x
Modular Tools
SEC-
30
SEC-WAVEMILL
WEZ series
Aluminum Alloy A2025 Machine Component Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ17063RS04 Single-Sided, 2 Corners
Grade H20 QChipbreaker S QCutter Dia. (mm) 63 63Number of Teeth 4 4vc (m/min) 1,187 1,187vf (mm/min) 1,920 1,920fz (mm/t) 0.08 0.08ap(mm) 1 1ae (mm) 50 50Coolant Q Q
ResultsVery little dimensional fluctuation and machining precision is stable
Pure Copper (Black Scale) Electrical Machinery Component Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ17100R05 Single-Sided, 4 Corners
Grade DL2000 QChipbreaker S QCutter Dia. (mm) 100 100Number of Teeth 5 5vc (m/min) 314 314vf (mm/min) 400 400fz (mm/t) 0.08 0.08ap(mm) 0.5 0.5ae (mm) 80 80Coolant Wet Wet
Results Holes does not have burrs, so no finishing needed
FRPP Resin Industrial Machine Component Sumitomo Comp’sHorizontal Machining Centre: BT50
Tool WEZ11020E02 Single-Sided, 2 Corners
Grade ACM300 QChipbreaker L QCutter Dia. (mm) 20 20Number of Teeth 2 3vc (m/min) 200 37vf (mm/min) 640 220fz (mm/t) 0.1 0.091ap(mm) 5 to 9 x 3 passes 5 to 9 x 3 passesae (mm) 0.95 x 1 pass 0.95 x 1 passCoolant Q Q
ResultsMinimized wall surface step, increasing machining efficiency
Resin Electronic Device Sumitomo Comp’sVertical Machining Centre BT40
Tool WEZ11080R07 Single-Sided, 2 Corners
Grade DL2000 QChipbreaker S QCutter Dia. (mm) 80 80Number of Teeth 7 7vc (m/min) 376 376vf (mm/min) 1,050 1,050fz (mm/t) 0.1 0.1ap(mm) 3 3ae (mm) 50 50Coolant Wet Wet
ResultsImproved cutting edge sharpness keeps machining quiet
Titanium Alloy Aerospace Component Sumitomo Comp’sCompound Lathe Tool WEZ17035E03 Single-Sided,
2 CornersGrade ACM300 QChipbreaker L QCutter Dia. (mm) 35 35Number of Teeth 3 3vc (m/min) 45 45vf (mm/min) Q Qfz (mm/t) 0.16 0.16ap(mm) 3 3ae (mm) 17.5 17.5Coolant Wet Wet
Results Tool life improved
Aluminum Alloy A5052 Machine Component Sumitomo Q5-axis Control Vertical Machining Centre HSK-A100
Tool WEZ17025M12Z2 Q
Grade DL2000 QChipbreaker S QCutter Dia. (mm) 25 QNumber of Teeth 2 Qvc (m/min) 785 Qvf (mm/min) 4,000 Qfz (mm/t) 0.2 Qap(mm) 3.9 Qae (mm) 25 QCoolant Wet Q
ResultsStable machining without chatter even at overhang 100 mm (L/D=4)
Modular Tools
SEC-
Nickel Based Alloy Inconel 718 Aerospace Components Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ17032E04 (Special Tool)
Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker H QCutter Dia. (mm) 32 32Number of Teeth 4 4vc (m/min) 30 30vf (mm/min) 120 120fz (mm/t) 0.1 0.1ap(mm) 5 5ae (mm) 10 10Coolant Wet Wet
Results 50% tool life improvement
Titanium Alloy Ti-6Al-4V Aerospace Components Sumitomo Comp’sVertical Machining Centre BT50
Tool WEZ11063RS08 Single-Sided, 2 Corners
Grade ACU2500 QChipbreaker G QCutter Dia. (mm) 63 63Number of Teeth 8 8vc (m/min) 48 48vf (mm/min) 310 310fz (mm/t) 0.16 0.16ap(mm) 2 2ae (mm) 50 50Coolant Wet Wet
Results Longer tool life with no chipping and less burr
31
M E M O
Very hot or lengthy chips may be discharged while the machine is in operation. Therefore, machine guards, safety goggles or other protective covers must be used. Fire safety precautions must also be considered.
When using non-water soluble cutting oil, precautions against fire must be taken and please ensure that a fire extinguisher is placed near the machine.
Please handle with care as this product has sharp edges.Improper cutting conditions or mis-handling of the tool may result in breakages or projectiles. Therefore, please use the tool within its recommended conditions.
< SAFETY NOTES >
R3 (2020.3) IV 1903 TP/AK
Hardmetal DivisionGlobal Marketing Department : 1-1-1, Koyakita, Itami, Hyogo 664-0016, Japan
Tel: +81-72-772-4535 Fax: +81-72-771-0088https://www.sumitool.com/global