Trouble Codes Copystar-Kyocera

FS-1028MFP, 1128MFPModelError CodeDescriptionTo enter Service ModeSim#To ExecuteService ChecksFS-1128MFP (2H92JN)C0030Fax Control PWB System Problem. Processing with the optional fax software was disabled due to a hardware problem.Turn power Off/On.1) Repl fax control PWB.FS-1128MFPC0070Fax Control PWB Incompatibility Problem. Fax software is not compatible with the main software.Turn power Off/On.1) Upgrade firmware to compatible versions, 2) Repl fax control PWB.FS-1028MFP, FS-1128MFPC0100Backup Memory Device Error. Defective flash memory or defective control PWB.Turn power Off/On.1) Replace the control PWB.FS-1028MFP, FS-1128MFPC0120MAC Address Data Error. Defective flash memory.Turn power Off/On.1) Replace the control PWB.FS-1028MFP, FS-1128MFPC0130Backup Memory Read/Write Error. Defective flash memory or defective control PWB.Turn power Off/On.1) Replace the control PWB.FS-1028MFP, FS-1128MFPC0140Backup Memory Data Error. Defective flash memory or defective control PWB.Turn power Off/On.1) Replace the control PWB.FS-1028MFP, FS-1128MFPC0150Control PWB EEPROM Error. Detecting control PWB EEPROM (U17) communication error.Turn power Off/On.1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB.FS-1028MFP, FS-1128MFPC0170Billing Counting Error. Defective control PWB or its EEPROM (U17).Turn power Off/On.1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB.FS-1028MFP, FS-1128MFPC0180Machine Number Mismatch Error. Machine number does not match on main and engine PWBs.Turn power Off/On.1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB, 3) Repl engine PWB.FS-1028MFP, FS-1128MFPC0420Paper Feeder Communication Error. Communication error between the control PWB and optional paper feeder.Turn power Off/On.1) Incorrect installation-reinstall, 2) Reseat YC30 @ control PWB & paper feeder interface connector, 3) Reseat YC5 @ control PWB & paper feeder interface connector, 4) Repl interface harness, 5) Repl control PWB, 6) Repl PF main PWB.FS-1128MFPC0830Flash ROM Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.Turn power Off/On.1) Upgrade firmware to compatible versions, 2) Repl fax control PWB.FS-1128MFPC0840Faults of RTC. The time is judged to go back based on the comparison of the RTC time and the current time, or (5) years or more have passed.Turn power Off/On.1) Reinstall the backup battery on the fax control PWB, 2) Repl fax control PWB.FS-1128MFPC0870Fax Control PWB to Main PWB High-Capacity Data Transfer Problem. High-capacity data transfer between fax control PWB and main PWB was not normally performed even if data transfer was tried several times.Turn power Off/On.1) Reinstall the fax control PWB, 2) Repl fax control PWB, 3) Repl control PWB.FS-1128MFPC0920Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax control PWB.Turn power Off/On.1) Repl fax control PWB.FS-1028MFP, FS-1128MFPC2000Main Motor Error. The main motor ready input is not given for 2 sec, after the main drive motor has turned On.Turn power Off/On.1) Reseat drive motor connector CN1 & control PWB connector YC17, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl main motor, 5) Repl control PWB.FS-1028MFP, FS-1128MFPC2610PF-100 Paper Feeder Motor Error. The PF paper feed motor ready input is not given for 2 sec, after the PF paper feed drive motor has turned On. (Optional paper feeder 1)Turn power Off/On.1) Reseat PF paper feed motor connector & PF main PWB connector YC4, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl PF paper feed motor, 5) Repl control PWB.FS-1028MFP, FS-1128MFPC2620PF-100 Paper Feeder Motor Error. The PF paper feed motor ready input is not given for 2 sec, after the PF paper feed drive motor has turned On. (Optional paper feeder 2)Turn power Off/On.1) Reseat PF paper feed motor connector & PF main PWB connector YC4, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl PF paper feed motor, 5) Repl control PWB.FS-1028MFP, FS-1128MFPC3100ISU Home Position Error. Home position is not correct when power is turned On, or copying a document from the contact glass.Turn power Off/On.1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Reseat FFC between YC6 @ control PWB & YC103 @ scanner PWB, 3) Reseat FFC between ISU motor & YC104 @ scanner PWB, 4) Replace FFC from YC6 to YC103, 5) Replace FFC from ISU motor to YC104, 6) Check/repl scanner HPS, 7) Check scanner drive components for excessive drag, 8) Repl scanner motor, 9) Repl image scanner unit (ISU).FS-1028MFP, FS-1128MFPC3200Exposure Lamp Error. The exposure lamp is not turned On.Turn power Off/On.1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Reseat FFC between YC6 @ control PWB & YC103 @ scanner PWB, 3) Reseat FFC between YC3 @ CCD PWB & YC101 @ inverter PWB, 4) Reseat FFC between YC102 @ inverter PWB & exposure lamp, 5) Replace FFC from YC6 to YC103, 6) Replace FFC from YC3 to YC101, 7) Replace FFC from inverter to exposure lamp, 8) Repl exposure lamp, 9) Repl inverter PWB, 10) Repl image scanner unit (ISU).FS-1028MFP, FS-1128MFPC3300AGC Error. After AGC the correct input is not obtained at the CCD.Turn power Off/On.1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Repl exposure lamp, 3) Repl CCD PWB, 4) Repl control PWB, 5) Repl image scanner unit (ISU).FS-1028MFP, FS-1128MFPC3500CPU-ASIC (CCD PWB) Communication Error. An error code is detected.Turn power Off/On.1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Repl exposure lamp, 3) Repl CCD PWB, 4) Repl control PWB, 5) Repl image scanner unit (ISU).FS-1028MFP, FS-1128MFPC4000Polygon Motor Error. Polygon motor ready input is not given for 6 sec while the polygon motor is On.Turn power Off/On.1) Reseat polygon motor connector & YC10 @ control PWB, 2) Repl polygon motor harness, 3) Repl laser unit, 4) Repl control PWB.FS-1028MFP, FS-1128MFPC4200Beam Detect Error. BD sensor does not detect the laser beam.Turn power Off/On.1) Possible condensation on polygon mirror. Clean or repl laser unit. 2) Reseat laser unit connectors, 3) Repl laser unit, 4) Repl control PWB.FS-1028MFP, FS-1128MFPC6000Broken Fuser Heater Wire. The temperature does not rise after the fuser heater lamp is turned On.Turn power Off/On.1) Reseat thermistor & heat lamp connections, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.FS-1028MFP, FS-1128MFPC6020Abnormally High Fuser Unit Thermistor Temperature. Thermistor detects abnormally high temperature.Turn power Off/On.1) Ohm out thermistor. If 0 ohms replace, 2) Repl control PWB.FS-1028MFP, FS-1128MFPC6030Broken Fuser Thermistor Wire.Input from fuser thermistor is 0 (A/D value).Turn power Off/On.1) Reseat thermistor & heat lamp connections, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.FS-1028MFP, FS-1128MFPC6400Zero-Cross Signal Error. The zero cross signal does not reach the control PWB for a specified time.Turn power Off/On.1) Check wall outlet ground to neutral voltage. 2) Reseat YC202 @ high voltage PWB & YC23 @ control PWB, 3) Reseat YC103 @ PSU & YC201 @ high voltage PWB, 4) Repl harness from YC202 to YC23, 5) Repl harness from YC103 to YC201, 6) Check YC103-8 @ PSU for zero-crossing signal. If absent repl PSU, 4) If zero-crossing signal is present repl control PWB.FS-1028MFP, FS-1128MFPC7990Waste Toner Full. The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.Turn power Off/On.1) Shake process unit side to side, then power Off/On, 2) Repl drum unit, then power Off/On, 3) Repl waste toner sensor, 4) Repl control PWB.FS-1028MFP, FS-1128MFPF000Control PWB-Operation panel PWB comunication error.Turn power Off/On.1) Reseat YC1 @ operation panel PWB & YC7 @ control PWB, 2) Repl harness from YC1 to YC7, 3) Repl operation panel PWB, 4) Replace control PWB.FS-1028MFP, FS-1128MFPF020Control PWB RAM Checksum Error. Defective main RAM on the control PWB or defective expanded memory DIMM.Turn power Off/On.1) Power Off/On, 2) Repl expanded memory DIMM, 3) Replace control PWB. Contact Service Administrative Division.FS-1028MFP, FS-1128MFPF040Control PWB Engine Communication Error.Turn power Off/On.1) Power Off/On, 2) Replace control PWB. Contact Service Administrative Division.FS-1028MFP, FS-1128MFPF041Control PWB-Scanner PWB Communication Error. A communication error is detected.Turn power Off/On.1) Power Off/On, 2) Replace control PWB, 3) Repl scanner PWB. Contact Service Administrative Division.FS-1028MFP, FS-1128MFPF050Control PWB Engine Checksum Error. Some error may have occurred while downloading firmware, or defective control PWB.Turn power Off/On.1) Reload current firmware, 2) Power Off/On, 3) Replace control PWB. Contact Service Administrative Division.FS-1028MFP, FS-1128MFPF186Control PWB Video Data Control Error.Turn power Off/On.1) Power Off/On, 2) Replace control PWB. Contact Service Administrative Division.FS-1128MFPE00000 or U00000Fax Communication Error: No response or line busy after the set number of redials.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00100 or U00100Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00200 or U00200Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00300 or U00300Fax Communication Error: Recording paper on the destination unit has run out during reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsLoad paper.FS-1128MFPE00420 or U00420Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00421 or U00421Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00430 or U00430Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00430 or U00430Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00431 or U00431Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00431 or U00431Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00432 or U00432Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00432 or U00432Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00433 or U00433Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00433 or U00433Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00434 or U00434Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00435 or U00435Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00435 or U00435Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00440 or U00440Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00440 or U00440Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00440 or U00440Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00441 or U00441Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00450 or U00450Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00460 or U00460Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00460 or U00460Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00462 or U00462Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00500 or U00500Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00600 or U00600Fax Communication Error: The document processor cover is open.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00601 or U00601Fax Communication Error: Document jam or the document length exceeds the maximum.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00602 or U00602Fax Communication Error: Image scanning section problem.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00603 or U00603Fax Communication Error: No document feed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00604 or U00604Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00610 or U00610Fax Communication Error: Recording section cover open.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00611 or U00611Fax Communication Error: Recording paper jam.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00613 or U00613Fax Communication Error: Image writing section problem.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00614 or U00614Fax Communication Error: Nearly empty of recording paper.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00615 or U00615Fax Communication Error: Empty of recording paper.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00620 or U00620Fax Communication Error: Copier fixing unit problem.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00622 or U00622Fax Communication Error: Copier drive motor problem.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00655 or U00655Fax Communication Error: CTS was not activated after RTS due to a modem error.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00656 or U00656Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00670 or U00670Fax Communication Error: Power was cut off during communication.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00677 or U00677Fax Communication Error: There was no file to transmit in the memory transmission mode.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00690 or U00690Fax Communication Error: System error.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00700 or U00700Fax Communication Error: Communication was interrupted because of a problem in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00800 or U00800Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE00810 or U00810Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE00900 or U00900Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE00910 or U00910Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE01000 or U01000Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01000 or U01000Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01001 or U01001Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01010 or U01010Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01011 or U01011Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01012 or U01012Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01013 or U01013Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01014 or U01014Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01015 or U01015Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01016 or U01016Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01017 or U01017Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01018 or U01018Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01019 or U01019Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01020 or U01020Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01021 or U01021Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01022 or U01022Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01023 or U01023Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01024 or U01024Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01025 or U01025Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01026 or U01026Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01027 or U01027Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01028 or U01028Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01040 or U01040Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01041 or U01041Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01042 or U01042Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01043 or U01043Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01044 or U01044Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE010x45 or U01045Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01046 or U01046Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01047 or U01047Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01048 or U01048Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01049 or U01049Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01050 or U01050Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01051 or U01051Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01052 or U01052Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01053 or U01053Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01054 or U01054Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01055 or U01055Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01056 or U01056Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01057 or U01057Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01070 or U01070Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01071 or U01071Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01072 or U01072Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brake in loop current was detected during transmission.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01073 or U01073Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01080 or U01080Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01091 or U01091Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01092 or U01092Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01100 or U01100Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01101 or U01101Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01102 or U01102Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01110 or U01110Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01111 or U01111Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01112 or U01112Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01113 or U01113Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01114 or U01114Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01115 or U01115Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01116 or U01116Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01117 or U01117Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01118 or U01118Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01119 or U01119Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01120 or U01120Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01121 or U01121Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01122 or U01122Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01123 or U01123Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01124 or U01124Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01125 or U01125Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01126 or U01126Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01127 or U01127Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01128 or U01128Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01129 or U01129Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01140 or U01140Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01141 or U01141Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01142 or U01142Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01143 or U01143Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01144 or U01144Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01145 or U01145Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01146 or U01146Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01147 or U01147Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01148 or U01148Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01149 or U01149Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIP signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01150 or U01150Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01151 or U01151Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01152 or U01152Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01153 or U01153Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01154 or U01154Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RNR signal (ECM).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01155 or U01155Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01160 or U01160Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01161 or U01161Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01162 or U01162Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01163 or U01163Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01164 or U01164Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01170 or U01170Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01172 or U01172Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01191 or U01191Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01199 or U01199Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01400 or U01400Fax Communication Error: An invalid one-touch key was specified during communication.Exxxxx: V.34 modem, Uxxxxx: all other modemsCheck the programming of the appropriate one-touch key.FS-1128MFPE01500 or U01500Fax Communication Error: A communication error occurred when calling in V.8 mode.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01600 or U01600Fax Communication Error: A communication error occurred when called in V.8 mode.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01700 or U01700Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01720 or U01720Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01721 or U01721Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01800 or U01800Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01810 or U01810Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01820 or U01820Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE01821 or U01821Fax Communication Error: Operation was interrupted due to the absence of a common communication speed between units. (including when an impossible combination of communication speed and symbol speed occurs) after MPh exchange, a DCN signal was transmitted to the destination unit and the line was cut.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE02000 or U02000Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE02100 or U02100Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE02200 or U02200Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE02200 or U02200Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE02200 or U02200Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE02303 or U02303Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE02304 or U02304Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.Exxxxx: V.34 modem, Uxxxxx: all other modemsPoor line conditions. Contact local phone provider.FS-1128MFPE02400 or U02400Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03000 or U03000Fax Communication Error: No document was present in the destination unit when polling reception started.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03100 or U03100Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03200 or U03200Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03200 or U03200Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03300 or U03300Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03300 or U03300Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03400 or U03400Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03500 or U03500Fax Communication Error: In confidential polling reception, the confidential, the specified confidential box number was not registered in the destination.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03500 or U03500Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03500 or U03500Fax Communication Error: The destination was being accessed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03600 or U03600Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03600 or U03600Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03700 or U03700Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE03700 or U03700Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04000 or U04000Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04000 or U04000Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04000 or U04000Fax Communication Error: The destination was being accessed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04100 or U04100Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04100 or U04100Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04200 or U04200Fax Communication Error: In encrypted transmission, the specified encryption box was not registered in the destination unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04300 or U04300Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04400 or U04400Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04401 or U04401Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE04500 or U04500Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE05000 or U05000Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE05100 or U05100Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE05200 or U05200Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE05300 or U05300Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE09000 or U09000Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE12000 or U12000Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE12000 or U12000Fax Communication Error: In subaddress-based relay reception memory overflowed.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE12100 or U12100Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE14000 or U14000Fax Communication Error: Memory overflowed during confidential reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE14000 or U14000Fax Communication Error: Memory overflowed in subaddress-based confidential reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE14100 or U14100Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE14100 or U14100Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE19000 or U19000Fax Communication Error: Memory overflowed during memory reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE19100 or U19100Fax Communication Error: Memory overflowed in the destination unit during transmission.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE19200 or U19200Fax Communication Error: Memory transmission failed because a decoding error occurred.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE19300 or U19300Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1128MFPE19400 or U19400Fax Communication Error: Reception failed because an error occurred during JBIG encoding.Exxxxx: V.34 modem, Uxxxxx: all other modemsFS-1028MFP, FS-1128MFPmessage"Add Toner."1) Replace toner container.FS-1028MFP, FS-1128MFPmessage"Cannot connect to Authentication Server."Press OK key.1) Check registration to Authentication server. 2) Check password and computer address for Authentication Server. 3) Check connection to network.FS-1028MFP, FS-1128MFPmessage"Cannot duplex print on this paper."1) To print without using duplex press OK. 2) Select the available paper type.FS-1028MFP, FS-1128MFPmessage"Cannot send fax."1) Cord connected? Check phone cord. 2) Is the permitted fax # or permitted ID # registered correctly? Check. 3) Has a communication error occurred? See above. 4) Is the destination fax line busy? Send again. 5) Does the destination fax machine respond? Send again. 6) Is there an error other than above? See above.FS-1028MFP, FS-1128MFPmessage"Close Document Processor."1) The document processor is still open even though an original has been inserted. Close the document processor. 2) Close the top cover of the document processor.FS-1028MFP, FS-1128MFPmessage"Close front cover."1) The top cover or the front cover is open. Close the covers securely.FS-1028MFP, FS-1128MFPmessage"Error occurred. Turn the main power switch off and on. C####"Turn power Off/On.1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.FS-1028MFP, FS-1128MFPmessage"File is not found. Job is cancelled."1) The specified file is not found. The job is cancelled. Press the OK key.FS-1028MFP, FS-1128MFPmessage"Incorrect account ID. Job is cancelled."1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.FS-1028MFP, FS-1128MFPmessage"Incorrect account ID."1) The Account ID does not match. Check the registered Account ID.FS-1028MFP, FS-1128MFPmessage"Incorrect Login User Name or Password. Job is cancelled."1) Enter the correct login user name or password.FS-1028MFP, FS-1128MFPmessage"Insufficient memory. Cannot start the job."1) Further scanning cannot be performed due to insufficient memory. Press the OK key to print the scanned pages. Press the Cancel key to cancel the printing job.FS-1028MFP, FS-1128MFPmessage"Job Accounting restriction exceeded. Cannot print."1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.FS-1028MFP, FS-1128MFPmessage"Job Accounting restriction exceeded. Cannot scan."1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.FS-1028MFP, FS-1128MFPmessage"Job Accounting restriction exceeded. Job is cancelled."1) The printing count exceeded the acceptable count restricted by Job Accounting. Cannot print any more. This job is cancelled. Press the OK key.FS-1028MFP, FS-1128MFPmessage"Load paper in MP Tray"1) The paper has run out. Add paper to the paper source.FS-1028MFP, FS-1128MFPmessage"Load paper to cassette 1"1) The paper has run out. Add paper to the paper source, 2) The cassette is not properly closed. Be sure the cassette it closed securely.FS-1028MFP, FS-1128MFPmessage"Machine failure. Call service. C####"Turn power Off/On.1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.FS-1028MFP, FS-1128MFPmessage"Memory is full. Print job cannot be processed completely."1) Unable to continue the job as the memory is used up. Press the OK key to print the scanned pages. The print job cannot be processed completely. Press the Cancel key to cancel the job.FS-1028MFP, FS-1128MFPmessage"Paper jammed."1) If a paper jam occurs the machine will stop and the location of the jam will be indicated on the Message Display. Leave the machine On and follow the instructions to removed the jammed paper.FS-1028MFP, FS-1128MFPmessage"Place original and press Start key."1) Remove originals from the document processor, put them back in their original order, and place them again. Press the Start key to resume printing. Press the Cancel key to cancel the job.FS-1028MFP, FS-1128MFPmessage"Remove original from Document Processor."1) Remove originals from the document processor, put them back in their original order, and place them again. Press the Start key to resume printing. Press the Cancel key to cancel the job.FS-1028MFP, FS-1128MFPmessage"Scanner memory is full. Job is cancelled."1) Scanning cannot be performed due to insufficient memory of scanner. The job is cancelled. Press the OK key.FS-1028MFP, FS-1128MFPmessage"Send error. ####"1) See below:FS-1128MFPmessage"Sub address/Polling box limit exceeded. Job is cancelled."1) Fax box is full and no further storage is available. The job is cancelled. Press the OK key.FS-1028MFP, FS-1128MFPmessage"The phone receiver is off the hook. Hang up."1) Put down the receiver.FS-1028MFP, FS-1128MFPmessage"Top tray is full of Paper. Remove the paper."1) Remove the paper from the top tray, and press the OK key to resume the job.FS-1028MFP, FS-1128MFPmessage"Unknown toner installed. PC"1) This message is displayed if the installed toner container's regional specification does not match the machine's.FS-1028MFP, FS-1128MFPmessage"Unknown toner installed."1) If the toner container was taken from a different machine of the same model while it was displaying the Add Toner message, ignore the message and use the toner.FS-1028MFP, FS-1128MFPmessage"USB memory error. Job is cancelled."1) This job is cancelled. Press the OK key.FS-1028MFP, FS-1128MFPSend Error 1101Error: FTP Host Name. Enter the disable host name/IP address.Send errors are displayed on the panel only, and not recorded.Enter the correct host name or IP address.FS-1028MFP, FS-1128MFPSend Error 1101Error: Host Name. SMTP server name is not set. Error SMTP server name.Send errors are displayed on the panel only, and not recorded.Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password or Shared Name/Folder Name. Assign disable SMB shared name.Send errors are displayed on the panel only, and not recorded.Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!$%^~[]`FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password or Shared Name/Folder Name. Assign disable SMB user/password.Send errors are displayed on the panel only, and not recorded.Enter the correct username/password.FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password or Shared Name/Folder Name. Assign the SMB user who is not allowed to access the folder.Send errors are displayed on the panel only, and not recorded.Enter the correct username/password. Check the access limit of destination folder.FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered.Send errors are displayed on the panel only, and not recorded.Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered.Send errors are displayed on the panel only, and not recorded.Scan folder is not shared out to the network properly.FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password or Shared Name/Folder Name. SMB host name error.Send errors are displayed on the panel only, and not recorded.Check if the prohibited letters are used to shared name: "&'()`;FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password. Assign disable FTP user/password.Send errors are displayed on the panel only, and not recorded.Enter the correct username/password.FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password. FTP domain name is not entered.Send errors are displayed on the panel only, and not recorded.Enter the user name with the form of either [DomainYUser] or [Domain/User].FS-1028MFP, FS-1128MFPSend Error 1102Error: Username/Password. User ID for email authentication is not entered or entered wrongly. Wrong authentication password is entered.Send errors are displayed on the panel only, and not recorded.Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.FS-1028MFP, FS-1128MFPSend Error 1103Error: Pathname or File Name. Assign disable FTP folder path.Send errors are displayed on the panel only, and not recorded.Enter correct folder path.FS-1028MFP, FS-1128MFPSend Error 1103Error: Pathname or File Name. Assign disable SMB folder path.Send errors are displayed on the panel only, and not recorded.Enter correct folder path.FS-1028MFP, FS-1128MFPSend Error 1103Error: Pathname or File Name. Connection to the FTP folder which is not permitted for reference/writing.Send errors are displayed on the panel only, and not recorded.Enter the correct username/password. Check the access limit of destination folder.FS-1028MFP, FS-1128MFPSend Error 1103Error: Pathname or File Name. Connection to the SMB folder which is not permitted for reference/writing.Send errors are displayed on the panel only, and not recorded.Enter the correct username/password. Check the access limit of destination folder.FS-1028MFP, FS-1128MFPSend Error 1103Error: Pathname or File Name. SMB domain name is not entered.Send errors are displayed on the panel only, and not recorded.Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].FS-1028MFP, FS-1128MFPSend Error 1104Error: No Recipient Address. The destination email address is not specified.Send errors are displayed on the panel only, and not recorded.Specify the destination address.FS-1028MFP, FS-1128MFPSend Error 1105Error: Not Supported Protocol. FTP protocol is set to OFF.Send errors are displayed on the panel only, and not recorded.Check ON in the [Scanner]-[FTP] screen in Command Center.FS-1028MFP, FS-1128MFPSend Error 1105Error: Not Supported Protocol. SMB protocol is set to OFF.Send errors are displayed on the panel only, and not recorded.Check ON in the [Scanner]-[SMB] screen in Command Center.FS-1028MFP, FS-1128MFPSend Error 1105Error: Not Supported Protocol. SMTP protocol is set to OFF.Send errors are displayed on the panel only, and not recorded.Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.FS-1028MFP, FS-1128MFPSend Error 1106Error: No Sender Info. Sender email address is not entered.Send errors are displayed on the panel only, and not recorded.Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Assign the wrong FTP port number.Send errors are displayed on the panel only, and not recorded.Enter the correct port number.FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Assign the wrong SMB port number.Send errors are displayed on the panel only, and not recorded.Enter the correct port number.FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Enter the disable FTP host name/IP address.Send errors are displayed on the panel only, and not recorded.Enter the correct host name or IP address.FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Enter the disable SMB host name/IP address.Send errors are displayed on the panel only, and not recorded.Enter the correct host name or IP address.FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Network FTP is not connected.Send errors are displayed on the panel only, and not recorded.Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Network SMB is not connected.Send errors are displayed on the panel only, and not recorded.Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Network SMTP is not connected.Send errors are displayed on the panel only, and not recorded.Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.Send errors are displayed on the panel only, and not recorded.Select valid POP3 user other than [Other].FS-1028MFP, FS-1128MFPSend Error 2101Error: Can Not Connect. The specified server is not SMTP server.Send errors are displayed on the panel only, and not recorded.Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.FS-1028MFP, FS-1128MFPSend Error 2102Error: Cannot Connect With Timeout. Send the server which does not support FTP server.Send errors are displayed on the panel only, and not recorded.Enter the correct host name or IP address.FS-1028MFP, FS-1128MFPSend Error 2102Error: Cannot Connect With Timeout. The FTP server is unable to communicate.Send errors are displayed on the panel only, and not recorded.Check if the server is operating properly.FS-1028MFP, FS-1128MFPSend Error 2102Error: Cannot Connect With Timeout. The SMTP server is unable to communicate.Send errors are displayed on the panel only, and not recorded.Check if the server is operating properly.FS-1028MFP, FS-1128MFPSend Error 2103Error: Response Wait With Timeout. The FTP server is unable to communicate.Send errors are displayed on the panel only, and not recorded.Check is the server is operating properly.FS-1028MFP, FS-1128MFPSend Error 2103Error: Response Wait With Timeout. The SMB server is unable to communicate.Send errors are displayed on the panel only, and not recorded.Check is the server is operating properly.FS-1028MFP, FS-1128MFPSend Error 2103Error: Response Wait With Timeout. The SMTP server is unable to communicate.Send errors are displayed on the panel only, and not recorded.Check is the server is operating properly.FS-1028MFP, FS-1128MFPSend Error 2201Error: FTP Network Transfer. Error occurs on the network.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2201Error: SMB Network Transfer. Error occurs on the network.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2201Error: SMTP Network Transfer. Error occurs on the network.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2202Error: FTP Network Transfer With Timeout. Error occurs on the network.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2202Error: SMTP Network Transfer With Timeout. Error occurs on the network.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2202Error: TWAIN Network Transfer With Timeout. Response is not returned from the server, above the specified time.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2202Error: TWAIN Network Transfer With Timeout. Response is not returned from the server, above the specified time.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2203Error: Response Wait With Timeout. Response is not returned from the FTP server, above specified time.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2203Error: Response Wait With Timeout. Response is not returned from the SMB server, above specified time.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2203Error: Response Wait With Timeout. Response is not returned from the SMTP server, above specified time.Send errors are displayed on the panel only, and not recorded.Check the network connection (cable, network condition within LAN, etc.).FS-1028MFP, FS-1128MFPSend Error 2204Error: Email Size Limit. The size of the email attachment exceeds its limit.Send errors are displayed on the panel only, and not recorded.Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.FS-1028MFP, FS-1128MFPSend Error 3101Error: Server Response. SMTP server setting is not authenticated normally.Send errors are displayed on the panel only, and not recorded.Check the settings for client/server authentication.FS-1028MFP, FS-1128MFPSend Error 3101Error: Server Response. The FTP server is error status.Send errors are displayed on the panel only, and not recorded.Check is the server is operating properly.FS-1028MFP, FS-1128MFPSend Error 3101Error: Server Response. The SMTP server is error status.Send errors are displayed on the panel only, and not recorded.Check is the server is operating properly.FS-1028MFP, FS-1128MFPSend Error 3201Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism found.Send errors are displayed on the panel only, and not recorded.Check the settings for client/server authentication mechanism.FS-1028MFP, FS-1128MFPSend Error 5101Error: Send Software Not Yet Connected. Operation handle error. Error for stored status in the operation handle.Power Off/On. Send errors are displayed on the panel only, and not recorded.Power Off/On.FS-1028MFP, FS-1128MFPSend Error 5102Error: Send Software Already Connected. Operation handle error. Error for stored status in the operation handle.Power Off/On. Send errors are displayed on the panel only, and not recorded.Power Off/On.FS-1028MFP, FS-1128MFPSend Error 5103Error: Send Software Not Yet Opened. Error for storage status in the operation handle.Power Off/On. Send errors are displayed on the panel only, and not recorded.Power Off/On.FS-1028MFP, FS-1128MFPSend Error 5104Error: Send Software Already Opened. Error for storage status in the operation handle.Power Off/On. Send errors are displayed on the panel only, and not recorded.Power Off/On.FS-1028MFP, FS-1128MFPSend Error 7101Error: Send Software Memor Allocation. Insufficient memory space.Power Off/On. Send errors are displayed on the panel only, and not recorded.Power Off/On.FS-1028MFP, FS-1128MFPSend Error 7102Error: Send Software Socket Create. Unable to create a communication socket.Power Off/On. Send errors are displayed on the panel only, and not recorded.Power Off/On.FS-1028MFP, FS-1128MFPSend Error 720fError: Send Software Unknown Error. Unable to determine the cause.Power Off/On. Send errors are displayed on the panel only, and not recorded.Power Off/On.FS-1028MFP, FS-1128MFPSend Error 9181Error: Email page Max Count Over. The number of pages of a send file exceeds 999 pages.Send errors are displayed on the panel only, and not recorded.Set the number of pages to 999 or less.FS-1028MFP, FS-1128MFPSend Error 9181Error: FTP page Max Count Over. The number of pages of a send file exceeds 999 pages.Send errors are displayed on the panel only, and not recorded.Set the number of pages to 999 or less.FS-1028MFP, FS-1128MFPSend Error 9181Error: SMB page Max Count Over. The number of pages of a send file exceeds 999 pages.Send errors are displayed on the panel only, and not recorded.Set the number of pages to 999 or less.FS-1028MFP, FS-1128MFPSend Error 9181Error: TWAIN page Max Count Over. The number of pages of a send file exceeds 999 pages.Send errors are displayed on the panel only, and not recorded.Set the number of pages to 999 or less.

CS-1820ModelError CodeDescriptionTo enter Service ModeSim#To ExecuteService ChecksCS-1820 (2GM)C0030Fax Control PWB System Problem. Processing with the optional fax software was disabled due to a software or hardware problem.Turn power Off/On.1) Repl fax control PWB.CS-1820C0070Fax Control PWB Incompatibility Problem. Fax software is not compatible with the main software.Turn power Off/On.1) Upgrade firmware to compatible versions.CS-1820C0150Engine PWB Backup Memory Read/Write Problem. Read and write data does not match.Turn power Off/On.1) Reload firmware, 2) Repl engine PWB.CS-1820C0160Engine PWB EEPROM Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.Turn power Off/On. If code immediately returns initialize all data: Press System Menu/Counter, ^/v to Service, press & hold Start + # + Enter,^/v to 20Enter > ^/v to Execute > Enter > power Off/On.1) Run simulation U020, 2) Repl backup RAM, 3) Repl engine PWB.CS-1820C0170Accounting Counts Problem. When the power is turned ON the total count and scan count are abnormal both on the main PWB and the engine PWB.Turn power Off/On.1) Repl engine PWB, 2) Repl main PWB.CS-1820C0180Machine Number Mismatch Error. Machine number does not match on main and engine PWBs.Turn power Off/On.1) Repl engine PWB, 2) Repl main PWB.CS-1820C0210Communication Problem between the main PWB and the engine PWB. When the power is turned ON, the machine does not detect the low level of SBSY and the high level of SDIR for 3 sec.Turn power Off/On.1) Reseat YC7 @ main PWB, 2) Reseat YC3 @ engine PWB, 3) Repl engine PWB, 4) Repl main PWB.CS-1820C0220Communication Problem between the Main PWB and Operation PWB. There is no reply after 20 retrys at communication.Turn power Off/On.1) Reseat YC13 @ main PWB, 2) Reseat YC3 @ operation PWB, 3) Repl main PWB, 4) Repl operation PWB.CS-1820C0280Fax Control PWB Communication Problem. Communication between the fax control PWB and the main PWB of the machine cannot be performed normally.Turn power Off/On.1) Reseat YC1 @ fax control PWB, 2) Reseat YC1 @ main PWB, 3) Repl fax control PWB, 3) Repl main PWB.CS-1820C0800Image processing problem. JAM05 is detected twice.Turn power Off/On.1) Repl engine PWB.CS-1820C0830Flash ROM Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.Turn power Off/On.1) Repl fax control PWB.CS-1820C0870Fax Control PWB to Main PWB High-Capacity Data Transfer Problem. High-capacity data transfer between fax control PWB and main PWB was not normally performed even if data transfer was tried several times.Turn power Off/On.1) Reseat YC1 @ fax control PWB, 2) Reseat YC1 @ main PWB, 3) Repl fax control PWB, 3) Repl main PWB.CS-1820C0880Fax Control PWB Program Archive Problem. When power is turned On the compressed program in the flash ROM on the fax control PWB was not successfully decompressed.Turn power Off/On.1) Repl fax control PWB.CS-1820C0920Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax control PWB.Turn power Off/On.1) Repl fax control PWB.CS-1820C2000Main Motor Problem. LOCK ALM signal remains high for 1 sec, 1 sec after the main drive motor has turned On.Turn power Off/On.1) Reseat drive motor connectors, 2) Check drive components for excessive drag, 3) Repl main motor.CS-1820C3100Scanner Carriage Problem. Home position is not correct when power is turned On, or copying a document from the contact glass.Turn power Off/On.1) Reseat YC10/YC11 @ engine PWB, 2) Check scanner drive components for excessive drag, 3) Check/repl scanner HPS, 4) Repl scanner motor, 5) Repl scanner PWB, 6) Repl engine PCB.CS-1820C3200Exposure Lamp Problem. In indication check before starting copying, the average value in scanning of the shading plate with the CCD is 128 or more.Turn power Off/On.1) Reseat YC7 @ scanner PWB, 2) Repl exposure lamp & inverter PCB, 3) Adjust shading plate detection position, 4) Repl scanner PWB.CS-1820C4000Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 15 sec of START signal turning On.Turn power Off/On.1) Reseat laser unit connectors, 2) Repl laser unit, 3) Repl engine PWB.CS-1820C4010Polygon Motor Steady-State Problem. The polygon motor rotation is not stable for 5 sec continuously after polygon motor stabilization.Turn power Off/On.1) Reseat laser unit connectors, 2) Repl laser unit, 3) Repl engine PWB.CS-1820C6000Broken Fuser Heater Wire. The temperature does not reach 50C/122F within 13.5 sec. The temperature does not reach 100C/212F within 10 sec. Primary stabilization exceeds 10 sec. Secondary stabilization exceeds 24 sec.Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,^/v to 163Enter > ^/v to Execute > Enter > power Off/On.1) Reseat YC4 @ power supply PWB, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.CS-1820C6020Abnormally High Fuser Unit Thermistor Temperature. Thermistor detects 230C/446F for 40ms or more.Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,^/v to 163Enter > ^/v to Execute > Enter > power Off/On.1) Ohm out thermistor. If 0 ohms replace, 2) Repl power supply PWB.CS-1820C6050Abnormally Low Fuser Unit Thermistor Temperature. Thermistor detects 90C/194F or less for 1 sec continuously after initialization.Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,^/v to 163Enter > ^/v to Execute > Enter > power Off/On.1) Reseat YC4 @ power supply PWB, 2) Ohm out thermistor. If infinite replace, 3) Check/repl thermal switch, 4) Check/repl fixing heaters.CS-1820C6400Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec of power up, or 5 sec after initialization.Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,^/v to 163Enter > ^/v to Execute > Enter > power Off/On.1) Check wall outlet ground to neutral voltage. 2) Reseat YC7 @ engine PWB & YC2 @ PSU, 3) Check YC2-11 @ PSU for zero-crossing signal. If absent repl PSU, 4) If zero-crossing signal is present repl engine PWB.CS-1820C7800Broken External Thermistor Wire. The input voltage is 0.5 v or less.Turn power Off/On.1) Reseat operation panel connectors, 2) Repl operation panel PWB.CS-1820C7810Short Circuited External Thermistor. The input voltage is 4.5 v or more.Turn power Off/On.1) Reseat operation panel connectors, 2) Repl operation panel PWB.CS-1820C7980Waste Toner Reservoir Overflow Problem (when the total number of copies is less than 100K sheets). After E31 is displayed, 1000 sheets may be copied before shutdown. Or waste toner exceeds 5 grams.Turn power Off/On.1) Shake process unit side to side, then power Off/On, 2) Repl process unit, then power Off/On, 3) Repl waste toner sensor, 4) Repl engine PWB.CS-1820C7990Waste Toner Reservoir Overflow Problem (when the total number of copies is more than 100K sheets). After E31 is displayed, 1000 sheets may be copied before shutdown. Or waste toner exceeds 5 grams.Turn power Off/On.1) Shake process unit side to side, then power Off/On, 2) Repl process unit, then power Off/On, 3) Repl waste toner sensor, 4) Repl engine PWB.CS-1820CF010ROM Checksum Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF012ROM Checksum Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF1xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF2xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF3xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF4xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF5xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF6xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF7xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CF8xxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.CS-1820CFxxxController System Error.Turn power Off/On.1) Power Off/On, 2) Replace main PWB.CS-1820E00000 or U00000Fax Communication Error: No response or line busy after the set number of redials.Exxxxx: V.34 modem, Uxxxxx: all other modemsCS-1820E00100 or U00100Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.Exxxxx: V.34 modem, Uxxxxx: all other modemsCS-1820E00200 or U00200Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.Exxxxx: V.34 modem, Uxxxxx: all other modemsCS-1820E00300 or U00300Fax Communication Error: Recording paper on the destination unit has run out during reception.Exxxxx: V.34 modem, Uxxxxx: all other modemsLoad paper.CS-1820E00420 or U00420Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.Exxxxx: V.34 modem, Uxxxxx: all other modemsCS-1820E00421 or U00421Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.Exxxxx: V.34 modem, Uxxxxx: all other modemsCS-1820E00430 or U00430Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.Exxxxx: V.34 modem, Uxxxxx: all other modemsCS-1820E00430 or U00430Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.Exxxxx: V.34 modem, Uxxxxx: all other modemsCS-1820E00431 or U00431Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress conf