TMW 453 FABRICATION - SEALANT - ERECTION R

www.pittcometals.com

ARCHITECTURAL METALS, INC.

TMW 453

JUNE 2019

TMW 453FABRICATION - SEALANT - ERECTION

AutoCAD SHX Text

R



TMW 453

JUNE 2019

TMW 453

JUNE 2019

AutoCAD SHX Text

R

SECTION 1General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Assessing the Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SECTION 2 TMW 453 Framing Members / Accessories . . . . . . . . . . . . . . . . . P1 - P4

SECTION 3 Fabrication Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F1 - F14

SECTION 4 Sealant and Erection Procedures . . . . . . . . . . . . . . . . . . . . . . . . . S1

Elevations to Illustrate Typical Conditions . . . . . . . . . . . . . . . . . . . S2 - S3Sealant and Erection Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . S4 - S17

SECTION 5 Glazing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G1 Glass Formula and Glazing Chart . . . . . . . . . . . . . . . . . . . . . . . . . . G2

This document was developed by Pittco Architectural Metals, Inc. as advisory information and published as apublic service for our customers. Pittco disclaims all warranties with regard to this information, including allimplied warranties of merchantability and fitness. In no event shall Pittco be liable for any damages whatsoeverfrom the use, application or adaptation of materials published herein. It is the sole responsibility of theuser/installer to evaluate the accuracy, completeness or usefulness of any information, opinions, advice or othercontent published herein. Please consult your Pittco representative if you have questions about this document.



TMW 453

JUNE 2019

GENERAL INSTALLATION NOTES

G1

AutoCAD SHX Text

R



TMW 453

JUNE 2019

TMW 453

JUNE 2019

2

AutoCAD SHX Text

R

SECTION 1 - GENERAL INSTALLATION NOTES:

GENERAL CONSTRUCTION NOTES

· Don't drop products during handling. Dropping or striking members against any solid objects will damage the finish and may cause fabricated jointsand applied sealants to fail. Stack with adequate separation so materials will not rub together. Use interleaving material if needed. Cardboardwrapped or paper interleaved material must be kept dry. Store products off the ground. Protect against the elements, and damage by otherconstruction trades.

· Keep material away from water, mud, and construction materials. Prevent cement, plaster or other materials from damaging the finish.

· Protect the erected framing by wrapping with Kraft paper or by erecting sheet plastic or canvas splatter screens. Cement, plaster, terrazzo and otheralkaline solutions are very harmful to the finish. Under no circumstances allow these materials to dry on the finish or permanent staining will occur.Remove immediately with mild soap and water.

· All materials should be checked for quality and quantity upon receipt, Pittco must be notified immediately of any discrepancies. Check to make sureyou have the required shims, supplies, sealants, and tools necessary for installation.

· Any material substitutions must be of equal or greater quality.

· Sealants must be compatible with all materials with which they have contact, including other sealant surfaces. Consult with your sealant supplier forrecommendations relative to shelf life, compatibility, priming, tooling, adhesion, safety, etc.

· "Fastening" will mean any method of securing one part to another or to adjacent materials. These instructions will specify only those fasteners usedwithin the system. (Perimeter or anchor fasteners are normally not specified due to varying surrounding conditions.)

· Glazing gaskets should be cut long to account for shrinkage. They should be installed by inserting both corners first, then the center of the gasketfollowed by the quarter points. Continue subdividing the opening until the gasket can be easily and completely rolled into the gasket pocket. Gasketsinstalled in this manner will close at the corners and will not shrink or pull back at the ends.

· Isolate all aluminum to be placed directly in contact with concrete with a heavy coat of bituminous paint. Isolate aluminum from incompatiblematerials with plastic shims, paint finish, or zinc rich primer.

· Any horizontals will act as collectors of infiltrated water and will direct water to the vertical pockets that will act as downspouts. Water deflectors mustbe installed above all lights of glass to insure that water is directed from the downspouts to the outside of the building. Sill flashing is not required inall applications, when flashing is required end dams should be utilized.

· Take field measurements BEFORE fabrication to ensure a proper fit. A minimum perimeter shim space of 3 4" is required at the head, and 12" sill andjambs. Joint at head may be increased to accommodate building movements and / or thermal expansion with a "T" anchor. Joint should be twice thetotal anticipated movement.



TMW 453

JUNE 2019

SECTION 1 - General Information

3

AutoCAD SHX Text

R

DL

WL

DL

WL

DL

WL

WL

DL

SPLICE

TYPE

A(S

ingl

e Sp

an)

TYPE

B(M

ultip

le S

pan

< 2

6 ft)

TYPE

C(M

ultip

le S

pan

w/S

plic

e - O

verh

ang)

Anchor Conditions/Locations

FRAM

E SI

ZE

MAXIMUM ROUGH OPENING

FRAME SIZE

MAX

IMUM

ROU

GH O

PENI

NG

ACTUAL OPENING

ACTU

AL O

PENI

NG

MINIMUM ALLOWANCE FOR SEALANT

SIZING THE FRAMING

ANCHOR TYPES AND LOCATIONS

1. Measure The Opening:

Before fabricating material, an accurate frame size should be determinedby physically measuring the actual dimensions of the intended opening.Because of construction tolerances and construction practices, the actualopening may not be in total accordance with the approved shop drawings.

· Measure the width of the opening in several places to determine theminimum opening width.

· Measure the height of the opening in several places to determine theminimum opening height.

· Check level and plumb of the opening and adjust width and heightmeasurements accordingly.

2. Determine The Frame Size:

· After determining the maximum rough opening width, subtract twicethe allowance for perimeter jamb sealant to determine the requiredframe width.

· After determining the maximum rough opening height, subtract theallowance for perimeter sealant at the sill and the allowance forperimeter sealant at the head to determine the required frame height.

3. Determine Anchor Conditions and Locations:

· Review the opening conditions to determine the type of anchoringrequired and the location of the anchors.

· Assess the surrounding structure to verify that if the type of anchorsshown on the shop drawings can be correctly installed.

· Note anchor types at each condition which will be used duringinstallation of the wall.

· Make sure the shop drawings reflect your notes before fabricating theframe.

DETERMINING THE FRAME SIZE BY MEASURING THEBUILDING OPENING AND CHECKING THE ANCHOR TYPESAND LOCATIONS BEFORE FABRICATION CAN HELPAVOID COSTLY FABRICATION ERRORS.

CHECK DIAGONALSFOR SQUARENESS

WL

bed frame



TMW 453

JUNE 2019

TMW 453

JUNE 2019

4

AutoCAD SHX Text

R

53-454

52-481

53-468

FRAMING MEMBERS

53-451

53-450

53-463

53-464

53-500

53-507

52-506

Head/Sill(Use with 52-481)

Mullion ClosureFor Verticals and Horizontals

IntermediateHorizontal

Jamb Mullion

Vertical Mullion(Use with 52-481)

Vertical MullionHeavy Wall

(Use with 52-481)

Expansion MullionMale HalfHeavy Wall

(Use with 52-256)

SSG Vertical Mullion(Use with 52-481)

SSG Expansion MullionMale HalfHeavy Wall

(Use with 52-506)

SSG Expansion MullionFemale Half

(Use with 52-507)

53-467Head Horizontal(Inside Set)

53-457Expansion Mullion

Male Half(Use with 52-456)

52-456Expansion Mullion

Female Half(Use with 53-457 and 53-464)

53-518SSG Horizontal

52-490

52-492

52-540

90° Outside CornerHalf Mullion

(2 Req'd)

135° OutsideCorner Half Mullion

(2 Req'd)

90° SSG OutsideCorner Half Mullion

(2 Req'd)

52-542135° SSG OutsideCorner Half Mullion

(2 Req'd)

52-486Glass Stop(1" Glazing)

52-487Glass Stop(1/4" Glazing)



TMW 453

JUNE 2019

Component Parts

P1

AutoCAD SHX Text

R

19-045

19-183

52-001

52-009

COVERS AND ADAPTERS

14" Glazing Adapter

Corner MullionLock

58" Glazing Adapter

Full Pocket Filler

52-035Interior Glass Stop(1" Glazing)

52-034Interior Glass Stop(1/4" Glazing)

52-488Interior Trim(Use w/ 52-034 / 52-035)

52-019Horizontal Re-glaze

Adapter

52-046Face / Cover90° Outside Corner

52-022Face / Cover135° Outside Corner

52-04090° Outside Corner

Mullion Adapter

12-00390° Corner Angle

52-029Outside Corner

Interior Trim

Isolator ClipCorner Trim

78-350-5100

52-016Face / Cover

52-010Face / Cover2" x 5/8"



TMW 453

JUNE 2019

TMW 453

JUNE 2019

Component Parts

P2

AutoCAD SHX Text

R

Setting Block15/16" - 1 1/4" Glazing(2) Required per Lite

70-881-6300

ACCESSORIES

Setting Block1" SSG Glazing

(2) Required per Lite

12-818-6300

Setting Block1/4" SSG Glazing


12-803-6300

Setting Block Shelf1" SSG Glazing


52-041-4150

Setting Block Chair1" SSG Glazing


53-006-4150

Jamb SpliceAt Glass Stop Area

(Remove paper before installation)

16-775-4150

Cover Splice(53-014)

(Remove paper before installation)

12-305-4250

12-305-6250

Water Deflector(Remove paper before installation)

70-702-4153

Horizontal Water DamSSG Mullions

52-050-4150

52-272-4150

90° Corner Splice(2 Req'd)

52-273-4150

135° Corner Splice(2 Req'd)

Temporary Glass Retainer 88-088-5100

Vertical Mullion End Cap(Remove paper before installation)

70-702-4160

Cover End Cap(Top of Vertical)

72-944-4151

52-000Retainer

Retainer(Use W/ 52-465)

53-000

Expansion MullionSplice

53-471-4150

Jamb and MullionSplice

53-470-4150

Expansion MullionSplice

(SSG Mullion)

52-521-4150



TMW 453

JUNE 2019

Component Parts

P3

AutoCAD SHX Text

R

FASTENERS AND GASKETS

Dense Silicone Gasket SSG GlazingInterior Spacer

12-916-6300

Adhesive Backed Foam Tape1/16" x 1/4"

70-890-6300

# 10-16 x 1"PFH Screw

Type B Point

10-119-4200

Attach 52-042 SSG1/4" Glazing Adapter

1/4-20 x 3/4"Hex Head Bolt

SEMS ET Lockwasher

10-377-4200

Attach 52-009

# 10-24 x 1/2"PFH Screw

Type F Point

Attach TransomSash

10-147-4254

# 10-16 x 1/2"PPH Screw

Type B Point

Attach Splices10-153-

4254

# 12-14 x 3/4"HWH Screw

Tek 3 Point

Attach Splices andStiffeners

10-241-4200

# 10-16 x 1 1/2"PPH Screw

Type B Point

Attach Horizntals10-379-

4254

1/4-20 x 1 3/4"Hex Head Bolt

SEMS ET Lockwasher

10-508-4200

Attach Corner AdapterSSG Mullions

# 10-16 x 1/2"HWH Screw

Tek 2 Point

Attach HorizontalRetainers and Splices

10-752-4200

Anti-Walk Spacer Block(1/2" Wide for Typical Int. Mullion)

12-908-6350

Solid EPDM Glazing Gasket(See Glazing Chart)

12-513-6300


12-514-6300

Foam EPDM Glazing Gasket(Expansion Mullions)

12-515-6300


12-521-6300


12-522-6300

Solid EPDM Glazing Gasket(Perimeter Gasket)

12-527-6300


17-004-6300


17-012-6300


17-013-6300

3/8-16 x 3 1/2"HWH Bolt

Structural Anchor 10-164-4200

3/8-16 x 3"HWH Bolt

Structural Anchor 10-165-4200

Anti-Walk Spacer Block(1" Wide for Jamb and Split Mullion)

12-908-6351



TMW 453

JUNE 2019

TMW 453

JUNE 2019

Component Parts

P4

AutoCAD SHX Text

R

LENGTH

DIM.

LENGTH

DIM.

DIM.

LEFT SIDE OF VERTICAL SHOWNRIGHT SIDE APPLICATION OPPOSITE HAND

VERTICAL MULLION CLOSURE PLATES

.201 DIA. (7 DRILL)

BOTT

OM

53-451 53-450

BOTT

OM

RIGHT SIDE OF VERTICAL MULLIONS SHOWNLEFT SIDE APPLICATION OPPOSITE HAND

VERTICAL MULLIONS

1"

53-46453-457

52-456 &53-463

1"

52-481

.201 DIA. (7 DRILL)

BOTT

OM

DIM.

.201 DIA. (7 DRILL)

BOTT

OM

DIM.

LENGTH

DIM.

1"

DIM.

LENGTH

DIM.

.201 DIA. (7 DRILL)

1116"

516"

1116"

114"11

4"

1116" 11

16"

114"

1116"

916

"27

8"

278"

114"

1116"

1116"

516"

114"

1116"

278"

218" 11

4"

1116"

HORIZ. HORIZ.HORIZ.

218"

1116"

1116"

114"

1116"

114"

FAB FOR53-454

FAB FOR53-468

OR53-518

FAB FOR53-454

HORIZ. HORIZ. HORIZ.

FAB FOR

53-454

OR

53-467

FAB FOR

52-466

52-465

SIMILAR

FAB FOR

53-454

278"

HORIZ. HORIZ. HORIZ. HORIZ. HORIZ. HORIZ.

FAB FOR53-454

FAB FOR52-466

FAB FOR53-454

OR53-467

FAB FOR53-454

FAB FOR53-468

FAB FOR53-454



TMW 453

JUNE 2019

SECTION 3 - Framing Fabrication

F1FAB

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

CLOSURE ANGLE90° OUTSIDE CORNER

VERTICAL LENGTH

INTERIOR TRIM

VERTICAL LENGTH

90° & 135° OUTSIDE CORNER

VERTICAL LENGTH

CORNER LOCK STRIP

52-490

12-003

52-029

52-009

135° OUTSIDE CORNER52-492 52-492

1"

BOTT

OM

90° OUTSIDE CORNER52-490

1"

BOTT

OM

FAB FOR53-454

DIM.

LENGTH

DIM.

53-468FAB FOR FAB FOR

53-454

FAB FOR

53-467

53-454OR

LENGTH

DIM.

DIM.

FAB FOR

52-465SIMILAR

52-466 53-454FAB FOR

278"

278"

218"

1116"

1116"

114"

1116"

114"

1116"

114"

1116"

114"

516"

1116"



.201 DIA. (7 DRILL)

.201 DIA. (7 DRILL)



TMW 453

JUNE 2019

TMW 453

JUNE 2019


F2FAB

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

1932"

"A"

52-481

3364

"

3"

30°

30°

INTERIOR TRIMS & STOPS

53-454

52-035 52-034 52-488

53-454

OUTSIDE SET53-468

1332

"

114"

114"

30°

3"

HORIZONTAL RETAINER

HORIZONTAL FACE52-016

19-183

ADAPTORS IF REQUIRED

SILL HORIZONTALS

52-00119-045 114"

53-000

INTERMEDIATE HORIZONTALS

358"

INSIDE SET52-465 52-466

53-454 53-467

HEAD HORIZONTALS

53-454 53-467

358"

15°

OTHER HORIZONTALS 1 7/16" FOR ALL HORIZONTALS 52-465 & 52-466"A" DIM.=1 11/32" FOR

HORIZONTAL CLOSURE PLATE

1 1/4"

58"

358"

58"

114"

58"

1332

"

358"

58"

1332

"

11764"

11764"

VERT.

VERT.VERT.

VERT. VERT.

VERT.VERT.

SLOT ASREQUIRED

SLOT ASREQUIRED



TMW 453

JUNE 2019


F3FAB

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R


52-03452-035 52-488

OUTSIDE SET53-468

358"

3" 114"

11332"

SILL HORIZONTALS

"A" DIM.=1 7/16" FOR 52-465 & 52-466 HORIZONTALS 1 9/16" FOR ALL OTHER HORIZONTALS


114"

"A"

30°


1332

"

114"

358"

30°

INSIDE SET52-465 52-466

HEAD HORIZONTALS

15°

3364

"

114"

52-481

358"

30°

3" 114"

58"

53-46753-454 53-454 53-467

58"35

8"

53-45453-454

HORIZONTAL FACE

19-045

ADAPTORS IF REQUIRED19-183 52-001

53-000

52-016

HORIZONTAL RETAINER

11764"

58"

1332

"

11764"

58"

1332

"

EXP. VERT

EXP. VERT

EXP. VERTEXP. VERT

EXP. VERT

EXP. VERT

EXP. VERT

SLOT ASREQUIRED

SLOT ASREQUIRED



TMW 453

JUNE 2019

TMW 453

JUNE 2019


F4FAB

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

3"

45°

1"


1132"

1316"

5"

45°

41532"

41532"

45°

30°

358"

58"35

8"

45°

5"

1116" DIM.

FOR 52-488

1164"

SILL HORIZONTALS

45°


52-035

*

52-034

*

53-454

52-488

53-4543"

53-000

HORIZONTAL FACE

19-045


HORIZONTAL RETAINER

1"

19-183

52-016

52-001

52-481

58"

1"30°

41532"

45°

OUTSIDE SET

REF. 45° & 22°30' ANGLE TAKEN FROM FACE OF INDIACTED WEB WALL

*

53-468

*

53-454

*

*

53-467

358"

* *

HEAD HORIZONTALS

52-466INSIDE SET


41532"

1332

"

53-454 53-467

*

* *

358"

11164"

1164"

1"

1"

30°

3364

"

30° 1"5

8"

1332

"58"

90°CORNER

1332

"

90°CORNER

90°CORNER

90°CORNER

90°CORNER

90°CORNER

90°CORNER

SLOT ASREQUIRED

SLOT ASREQUIRED



TMW 453

JUNE 2019


F5FAB

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R


REF. 45° & 22°30' ANGLE TAKEN FROM FACE OF INDIACTED WEB WALL

12732"

52-03452-035

* *

52-488

*

45°

3364

"

**

45°

22°30' 22°30'

4964" DIM.

FOR 52-488

22°30'

78"

18"


2"

358"

SILL HORIZONTALS

18"7

8"

12732"

22°30'

45°18"

78"

3"

INSIDE SET52-465 52-466

2932"

5764"

78"

18"

116"

1316"


78"

22°30'

1116"

52-481

HEAD HORIZONTALS

358"

78"

22°30'

45°

2" 3"

12732"

18"

12732"

*

53-45453-454 53-467

358"

* *

58"

53-467

*

OUTSIDE SET53-468

*

58"35

8"

53-454 53-454

* *

53-000

HORIZONTAL FACE52-016

HORIZONTAL RETAINER

ADAPTORS IF REQUIRED19-04519-183 52-001

58"

SLOT ASREQUIRED

SLOT ASREQUIRED

58"

135°CORNER

1332

"

135°CORNER

135°CORNER

135°CORNER

135°CORNER

135°CORNER

1332

"

1332

"



TMW 453

JUNE 2019

TMW 453

JUNE 2019


F6FAB

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

FOR VERTICAL ABOVE VERTICAL EXPANSION JOINTVERTICAL LENGTH

FOR VERTICAL BELOW VERTICAL EXPANSION JOINT

VERTICAL LENGTH

VERTICAL RETAINERS

VERTICAL FACE

VERTICAL LENGTH

VERTICAL GLAZING POCKET ADAPTORS

VERTICAL LENGTH

VERTICAL LENGTH

VERTICAL LENGTH

VERTICAL GLAZING POCKET CLOSURE

19-045 & 19-183 SHOWN FOR RIGHT SIDEOF VERTICAL MULLION - LEFT SIDE OPPOSITE

"A" DIM. = 1 1/4" FOR OUTSIDE SET HORIZONTAL 1 3/16" FOR INSIDE SET HORIZONTAL

VERTICAL LENGTH



VERTICAL LENGTH

VERTICAL LENGTH

VERTICAL LENGTH

VERTICAL GLAZING POCKET CLOSURE

"A"

TOP OF VERT.AT EXP. JOINT

AT EXP. JOINTTOP OF VERT.


19-183

19-045

52-001

19-183

VERTICAL EXPANSION JOINTFOR VERTICAL BELOW

114"

114"

19-183

19-045

"A"

*

"A"

VERTICAL LENGTH

FOR VERTICAL IN MIDDLE OF WALL VERTICALLY

FOR VERTICAL AT TOP OF WALLVERTICAL LENGTH

AT EXP. JOINTBOTTOM OF VERT.

FOR VERTICAL AT BOTTOM OF WALL

VERTICAL LENGTH

VERTICAL LENGTH

VERTICAL LENGTH

VERTICAL LENGTH"A"

52-001

19-045

52-018

VERTICAL FACE

TOP OFHEAD HORIZ.

53-000

FOR VERTICAL ABOVEVERTICAL EXPANSION JOINT

52-001

SILL HORIZ.BOTTOM OF

53-014

53-000


114"

114"



HORIZ.

HORIZ.

HORIZ.


HORIZ. (UPPER) HORIZ. (LOWER)

HORIZ. (UPPER) HORIZ. (LOWER)

HORIZ. (UPPER)

HORIZ. (UPPER)



(LOWER) HORIZ.

(LOWER) HORIZ.

VERTICAL RETAINERS

*

*

*

*



TMW 453

JUNE 2019


F7FAB

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

VERTICAL LENGTH = (DLO + 138")

DLO

1/4" GLAZING ADAPTOR

HORIZONTAL LENGTH =(DLO + 0) -1/32"

1/4" GLAZING ADAPTOR

52-04211

4"

1116"

52-042

114"

53-500

RIGHT SIDE OF VERTICAL MULLIONS SHOWN

VERTICAL LENGTH

114"

LEFT SIDE APPLICATION OPPOSITE HAND

VERTICAL MULLIONS

114"

1116"

52-051

JAMB FILLER

53-50752-506 &

1116"

LENGTH

DIM.

218"

1116"

DIM.

LENGTH27

8"

1116"

114"

1"

114"

1116"

53-454FAB FOR

53-467OR

1116"

DIM.11

4"5/16"

53-454FAB FOR

114"

1116"

DIM.

FAB FOR

52-465SIMILAR

52-466

BOTT

OM

FAB FOR53-454 53-454

FAB FORFAB FOR53-468

BOTT

OM278"

1"

HORIZ. HORIZ.

VERT. VERT.


HORIZ.HORIZ. HORIZ.

.201 DIA. (7 DRILL)

.201 DIA. (7 DRILL)



TMW 453

JUNE 2019

TMW 453

JUNE 2019


F8

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

VERTICAL LENGTH

90° OUTSIDE CORNER FACE

VERTICAL LENGTH


ABOVE SPLICE JOINT

LENGTH=VERT. LENGTH+DIM.-1/4"


VERTICAL LENGTH

LENGTH=VERT. LENGTH-DIM.-1/4"

VERTICAL LENGTH

90° OUTSIDE CORNER GUTTER


112"

VERTICAL LENGTH


VERTICAL LENGTH


112"

52-040

52-040

52-040

AT EXP. JOINTTOP OF VERT.

52-046

52-046

52-046

OF

V

ER

T.

TO

P

14"

INTER. HORIZ.

DIM.

2732

"

VERTICAL LENGTH


90° OUTSIDE CORNER135° OUTSIDE CORNER

52-022

52-542 52-542 52-540 52-540

14"

DIM.

BO

TT

OM

OF

V

ER

T.

1"

114"

1116"

278"

1"

114"

1116"

278"

FAB FOR

516"

DIM.

DIM.

LENGTH

218"

DIM.

LENGTH

DIM.

1116"

53-467

FAB FOR53-454

OR

1116"

114"

1116"

114"

1116"

52-466FAB FOR53-454

BOTT

OM

FAB FOR53-468

FAB FOR53-454

FAB FOR53-454

BOTT

OM

.201 DIA. (7 DRILL)

.201 DIA. (7 DRILL)



ABOVE SPLICE JOINT INTER. HORIZ.



TMW 453

JUNE 2019

FABRICATION PROCEDURES

F9

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

114"


52-03452-035 52-488

OUTSIDE SET53-468

114"

1932"

1716"

11764"


114" 3"

358"

58"

SILL HORIZONTALS

52-465INSIDE SET

52-466

11764"


52-481

114"

114"

358"

58"

HEAD HORIZONTALS

3"

58"35

8"

53-46753-454 53-454 53-467

358"

58"

53-45453-454

52-001


52-016

19-045

HORIZONTAL FACE

19-183

HORIZONTAL RETAINER53-000

VERT.

VERT.VERT.

VERT. VERT.

VERT.

VERT.

SLOT ASREQUIRED

SLOT ASREQUIRED



TMW 453

JUNE 2019

TMW 453

JUNE 2019


F10

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

3"


358"

58"

SILL HORIZONTALS

11764"

52-034


52-035 52-488

3" 114"

11332"

114"

1916"

52-481

114"

OUTSIDE SET53-468

HEAD HORIZONTALS

INSIDE SET


52-465 52-466

11764"

58"

114"

114"

358"

53-467

358"

53-4545

8"53-454 53-467

53-454

358"

58"

53-454


19-045

HORIZONTAL FACE

52-016

19-183 52-001

53-000

HORIZONTAL RETAINER

EXP. VERT

EXP. VERT

EXP. VERTEXP. VERT

EXP. VERT

EXP. VERT

EXP. VERT

SLOT ASREQUIRED

SLOT ASREQUIRED



TMW 453

JUNE 2019


F11

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R


45°

52-03452-035 52-488

OUTSIDE SET53-468

45°


52-001

45°

732"

3132"

114"

52-035

52-488

52-034 19-183 19-045


45°

7"

358"

SILL HORIZONTALS

58"

58"

5"

INSIDE SET52-465 52-466

45°

22332"

45°

732"

732"

1932"

52-002

52-001

52-003

34"

45°

11132"


52-481

2"

HEAD HORIZONTALS

358"

5"

45°

58"

7"

*

53-45453-454 53-467

358"

* *

58"

53-467

*

358"

58"

53-454 53-454

52-016

HORIZONTAL RETAINER

HORIZONTAL FACE

53-000

58"

58"

90°CORNER

90°CORNER

90°CORNER

90°CORNER

90°CORNER

90°CORNER

90° CORNEROUTSIDE

SLOT ASREQUIRED

SLOT ASREQUIRED



TMW 453

JUNE 2019

TMW 453

JUNE 2019


F12

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

3"

1"

1516"

52-002

52-003

52-001


5"

18°30'

358"

5"

34"

1"

1332"

SILL HORIZONTALS

18°30'


52-035 52-034 52-488

52-034

52-035

52-488

3"


19-04519-183

1932"

34"

78"52-001

716"

52-481

716"

18°30'

OUTSIDE SET53-468

HEAD HORIZONTALS

INSIDE SET


52-465 52-46635

8"

18°30'

1764"

18°30'

18°30'

1332"

716"

52-466

52-465

716"

53-4545

8"53-454 53-467

358"

53-467

58"35

8"

53-454 53-454

HORIZONTAL RETAINER53-000

52-016

HORIZONTAL FACE

58"

58"

SLOT ASREQUIRED

SLOT ASREQUIRED

135°CORNER

135°CORNER

135°CORNER

135°CORNER

135°CORNER

135°CORNER

135° CORNEROUTSIDE



TMW 453

JUNE 2019


F13

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

41732"

FACE OF INDIACTED WEB WALLREF. 45° & 22°30' ANGLE TAKEN FROM

AT 135° INSIDE CORNERHORIZONTAL RETAINER & FACES

HORIZONTAL RETAINER & FACES

45°

52-016

53-518

*

114"

53-518

732"

138"

34"

INTERMEDIATE VERTICAL & HORIZONTAL

52-019

22°30'

58"

114"

AT 90° INSIDE CORNER

52-016

53-000

45°

114"

138"

HORIZONTAL REGLAZE ADAPTOR

INTERMEDIATE HORIZONTAL

116"

1"53-518

*

22°30'

78"

532"

178"

53-000

*

90°CORNER

135°CORNER

MULLION

INSIDE90° CORNER

INSIDE135° CORNER

MULLION

EXP. VERT.

90° CORNER & VERT.135° CORNER



TMW 453

JUNE 2019

TMW 453

JUNE 2019


F14

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

C

AutoCAD SHX Text

R

SECTION 4 - SEALANT AND ERECTION PROCEDURES

In all the following details the perimeter sealant should be applied BEFORE THE FACE AND RETAINER ARE INSTALLED. However, the areabetween the outboard edge of the sill closure plate and the vertical retainer must be left open to allow water drainage.

When using 52-251 jambs preload exterior isolator gasket prior to installation.

Standard system splice joint including 2 sided SSG horizontals:Backer rod at vertical expansion joint should be approximately the same length as the metal splice and completely covered with sealant.(Refer to details 11, 12, 13 and 17.) When the vertical mullion has been properly located and anchored, apply a non-hardening,non-skinning sealant at the 1/2" nominal expansion joint to the entire front surface and return on each side approximately 1/2". Apply enoughsealant to front side of mullion to make a sealant reservoir so when mullion expands, sealant will not be overstretched. (Refer to details 14,15, 16 and 18.)

SSG 2 sided vertical, vertical splice joint:At the 1/2" vertical expansion joints this area must be sealed with a low modulus silicone compatible to the silicone used to structurally bondthe glass to the mullion. (Refer to details 31, 32 and 33.)

Anchorage of verticals at floor edge:Anchors should be arranged so that they always occur on the same side of the vertical mullions in the spandrel area, when glazing light fromthe interior. When this cannot be accomplished, glazing of this light may require the "re-glazing from exterior" procedure shown in details 9and 10 or the use of 52-265 horizontal. The glass edge spacer #12-908-6350 must be installed in the "deep" glazing pocket after the glassis set. These anti-walk spacers should be a minimum of two per light of glass spaced approximately 12" from top and bottom, and 3'-0" oncenter, maximum. For SSG verticals, interior corner lights cannot actually be set into the mullion from the interior of the building but must beset from the exterior even though they may be handled from the "floor". Of course the exterior weather seal must be installed from the exterior.Anti-walk spacers are not required on SSG verticals.

Glazing bead installation:For best watertight results, 17-004-6300 should be cut daylight opening plus 1/2". This will assure good tight joints at corners. Formaximum performance (8 P.S.F. water and higher), a bead of sealant should be placed in glazing bead pocket at each corner beforeinstalling 17-004-6300. Run sealant approximately 1-1/2" to 2" each way from corner. When installing 17-004-6300 be sure some sealantseals corners of 17-004-6300. Exterior glazing bead (12-514-6300) does not require this sealant.

Special SSG notes:On SSG mullions where "sealant" is in contact with the silicone sealant this "sealant" must be silicone compatible. Exterior horizontal facescrossing structural silicone verticals may be continuous across these verticals but must have an expansion joint at the expansion verticalwide enough to accommodate horizontal expansion. Of course when this is done the entire face will have to be removed during any exteriorre-glaze operations and is not recommended. When applying structural silicone to bond glass to mullion and weather seal silicone to sealbetween lights of glass, it is recommended that masking tape be applied either side of this silicone joint before applying silicone. Siliconemust be tooled into the joint and immediately after have tape removed before silicone begins to "Skin Over". Of course all glass and metaledges must be cleaned immediately before applying silicone as per silicone manufacturers' recommendations.



TMW 453

JUNE 2019

SECTION 4 - Sealant and Erection

S1

AutoCAD SHX Text

R

17

18

4

ELEVATION

FLOOR PLAN

A COMPOSITE ELEVATION TO ILLUSTRATE TYPICAL CONDITIONS

14

1

INDICATES 1/4" INFILL

16

3

15

9

6

5

2

11

8

13 19 12

4

SILL

@

OPP.

1

SECTION

10

OPP.

7



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S2

AutoCAD SHX Text

R

FLOOR PLAN

SIM.

22

31

DETAILS NOTED REFER TO EFG DETAILS ONLY

31

26

FLOOR PLAN

A COMPOSITE ELEVATION TO ILLUSTRATE TYPICAL CONDITIONS

1

ELEVATION

25

*

1

14

7

10

*

INDICATES 1/4" INFILL

3

*

23

16

*

32

* *

*

11

9

10

13

*

OPP.

1

OPP.

7

28

*

SILL

@

25

ELEVATION

* *

21

*

*

*

28

33

30

SIM.

30

*

OPP.

1

SECTION

*

SIM.

29 29

*

*

24

*

27

OPP.

7



TMW 453

JUNE 2019


S3

AutoCAD SHX Text

R

NOTE:

ISOLATOR GASKET PRIOR TO INSTALLATION OF FRAMING.WHEN USING 53-451 AT JAMB PRELOAD EXTERIOR

PERIMETER SEALANTWITH BACKER ROD

70-702-4160END CAP FIELD

3

END CAP FIELDINSTALLED

70-702-4160

SEALANT

INSTALLED

1

SEALANT

AS REQ'D

2A

END CAP FIELD70-702-4160

CONTINUOUS

VERTICAL/SILL INTERSECTION

2B

OF PERIMETER SEALANTINSTALLATION AND TOASSURE PROPER WEAPAGEOF SYSTEM AT BOTTOM

MITER BOTTOM OF VERTICALAS SHOWN TO ALLOW EASE

BOLTS IN GLASSPOCKET WITH SEALANT

HEADS OF ALL ANCHORCOMPLETELY COVER

WITH BACKER RODAS REQ'D

PERIMETER SEALANT

EXPANSION MULLION/

SILL INTERSECTION

COMPLETELY COVER

BOLTS IN GLASSHEADS OF ALL ANCHOR

POCKET WITH SEALANT

JAMB/SILL INTERSECTION

OF VERTICAL.

SEALANT

INSTALLED

2

INSTALLED

70-702-4160END CAP FIELD

SEALANT

WITH BACKER RODPERIMETER SEALANT

AS REQ'D

DOUBLE-FACE45

°

SECTION

SECTION

TAPE

2A

2B

IN ALL VERTICAL TO HORIZONTALINTERSECTIONS, SEALANT MUSTBE APPLIED SO AS TO FILLWEATHERSTRIP POCKET FLUSHWITH EXPOSED SURFACE.

53-451

NOTE:

2A

COMPLETELYCOVER HEADSOF ALL ANCHORBOLTS IN GLASSPOCKET WITHSEALANT

2B

53-454

52-481

NOTES:

1. All closure plates must be completely sealed to ends of verticalsand horizontals. This includes the glass dividing web of the verticalmullion across the front of the web. To aid this, the end cap must beset back 3/16" from the exterior plane of the glass.

2. In all these details, the perimeter sealant should be appliedBEFORE THE FACE AND RETAINER ARE INSTALLED. In any event thearea between the outboard edge of the sill closure plate and thevertical retainer must be left open to allow weepage.

3. On single height frames it is suggested that the mullion closureplate be installed at the top of the left frame and at the bottom of theright frame. This will allow the two frames to be snapped togetherslightly above each other, then slid together into proper alignment.Final sealing of these closure plates should be done after frames are inplace.



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S4

AutoCAD SHX Text

R

90 DEG. OUTSIDE CORNER/SILL INTERSECTION

PERIMETER SEALANT

FIELD MODIFIED AS SHOWN,70-702-4160 END CAP

VERTICAL/INTERMEDIATE HORIZONTAL INTERSECTION

5

COMPLETELY FILL GLAZING

SEALANT AT VERTICAL &HORIZONTAL INTERSECTION

REGLET

70-702-4153WATER DEFLECTORFIELD INSTALLEDAFTER ASSEMBLY

10-379-4200TYPICAL

FIELD INSTALLED

4

WITH BACKER RODAS REQ'D

SEALANT ON BOTHSIDES OF VERT. WEB

COMPLETELY FILL BOLTCHASE WITH SEALANT

12-515-6300

DETAIL SHOWING EXPANSIONMULLION ENGAGEMENTEngage mullion halves by swinginghalf mullion out approximately 10degrees and snapping together as

Typical mullions are more easilysnapped together by engagingback edge first.

shown.



TMW 453

JUNE 2019


S5

AutoCAD SHX Text

R

VERTICAL/INTERMEDIATE HORIZONTAL TOP VIEW

5A

SEALANT AT VERTICAL & HORIZONTALINTERSECTION COMPLETELY FILL

GLAZING REGLET

1

53-450

52-481

53-468

CUT GASKETS D.L.O. + 14"PER FOOT OF D.L.O.

4

FILL GLAZING REGLET WITHSEALANT FOR 1" AT FRAME

JOINTS

5

PLACE DROP OF SEALANT ON GASKETEND

6

SEAL JOINT BETWEEN DEFLECTOR,HORIZONTAL AND VERTICAL FROM TOP

AND BOTTOM OF JOINT

3

DO NOT SEAL EXTERIOR EDGE OFDEFLECTOR

PRESS CENTER OF GASKET INTO HORIZONTALREGLET SO THAT ENDS OF GASKET SLIDE TO

BUTT VERTICAL GASKET - WIPE EXCESSSEALANT

7

1"

1"


4

1. BEFORE APPLYING ANY SEALANT FOLLOW SEALANT MANUFACTURER'S INSTRUCTION FOR CLEANING / PRIMING. USE A GOOD GRADE SILICONE SEALANT AND COMPLETELYFILL THE GLAZING REGLET BETWEEN THE END OF THE HORIZONTAL AND THE VERTICAL FRAMING MEMBERS.

2. THE DEFLECTOR 70-702-4153 HAS AN ADHESIVE PAD. REMOVE THE LINING AND ADHERE THE DEFLECTOR TO THE UNDERSIDE OF THE HORIZONTAL GLAZING POCKET MAKINGSURE TO PLACE DEFLECTOR TIGHT TO INTERIOR SIDE OF FRAMING AND TIGHT TO BOTTOM OF VERTICAL GLAZING POCKET.

3. AFTER DEFLECTOR IS IN PLACE SEAL BETWEEN DEFLECTOR AND FRAMING MEMBERS. THE SEALANT IS INTENDED TO DIRECT ANY WATER IN THE HORIZONTAL GLAZINGPOCKET TO THE VERTICAL GLAZING POCKET WHERE IT WILL DRAIN OFF THE EXTERIOR MOST EDGE OF THE DEFLECTOR DOWN THE VERTICAL TO THE SILL. DO NOT SEAL THEEXTERIOR MOST EDGE OF THE DEFLECTOR.

4. THE GASKETS ARE TO BE CUT LONGER THAN THE DLO. IT IS RECOMMENDED THAT THE GASKET BE DLO PLUS ¼" FOR EACH FOOT OF DLO SIZE. SO FOR EXAMPLE A 4' DLOWOULD USE A GASKET 48" + (4) X ¼" OR 49" LONG.

5. BEFORE INSERTING GASKETS PREP CORNERS WITH A BEAD OF SEALANT IN THE GLAZING REGLETS FOR 1" BOTH VERTICALLY AND HORIZONTALLY FROM THE CORNER.6. INSTALL THE VERTICAL GASKETS . WHILE INSTALLING HORIZONTAL GASKETS INSERT ENDS OF GASKET INTO REGLETS A FEW INCHES FROM THE ENDS AND THEN APPLY A

SMALL BEAD OF SEALANT TO THE END OF THE GASKET.7. AS REMAINDER OF HORIZONTAL GASKET IS PRESSED INTO REGLET THE ENDS OF THE GASKET WILL SLIDE TIGHT TO THE VERTICAL GASKET. A GOOD APPLICATION OF

SEALANT WILL CREATE A SMALL SQUEEZE OUT OF SEALANT AT THE END WHICH CAN BE TOOLED FLUSH.



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S6

AutoCAD SHX Text

R

VERTICAL/INTERMEDIATE HORIZONTAL BOTTOM VIEW

5B

SEAL JOINT BETWEEN DEFLECTOR,HORIZONTAL AND VERTICAL FROM TOP

AND BOTTOM OF JOINT

3

SEALANT AT VERTICAL & HORIZONTALINTERSECTION COMPLETELY FILL GLAZING

REGLET

1

FILL GLAZING REGLET WITHSEALANT FOR 1" AT FRAME

JOINTS

5

USE ADHSIVE PAD ON DEFLECTOR TO ADHEREDEFLECTOR TO HORIZONTAL

2

PRESS CENTER OF GASKET INTO HORIZONTALREGLET SO THAT ENDS OF GASKET SLIDE TO

BUTT VERTICAL GASKET - WIPE EXCESSSEALANT

7


4

53-468

53-45052-481


4

1"

1"

PLACE DROP OF SEALANT ON GASKETEND

6

DO NOT SEAL EXTERIOR EDGE OFDEFLECTOR



TMW 453

JUNE 2019


S7

AutoCAD SHX Text

R

53-450

52-481

53-468

DO NOT SEAL JOINT BETWEEN VERTICALAND HORIZONTAL RETAINER

DO NOT SEAL BETWEENEXTERIOR GASKETS

VERTICAL/INTERMEDIATE HORIZONTAL TOP VIEW

5C

53-000



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S8

AutoCAD SHX Text

R

VERTICAL/INTERMEDIATE HORIZONTAL

INTERSECTION WITH GLAZING ADAPTORS

6

(INSIDE SET)

JAMB/HEAD INTERSECTION

7

PERIMETER SEALANT

JOINT AND MUST BE DONE ONTHIS SEALS THE METAL TO METALINSTALLING GLAZING ADAPTORS.GLAZING BEAD POCKET BEFORETAPE TO FACE OF MULLIONAPPLY 70-890-6300 SEALANT

FIELD INSTALLEDCLOSURE ANGLE72-944-4152

END CAP FIELD70-702-4160

SEALANT

INSTALLED

ALL ADAPTORS.

AS REQUIREDWITH BACKER ROD

OF GLAZING ADAPTOR.ADAPTOR. BE SURE TO SEAL TOPADAPTOR AGAINST VERTICALAT ENDS HORIZONTAL AROUNDHORIZONTAL INTERSECTION ALSOSEALANT AT VERTICAL &



TMW 453

JUNE 2019


S9

AutoCAD SHX Text

R

TO REGLAZE FROM EXTERIOR Remove broken glass, glazing beads and faces.Cut off horizontal extrusion 52-266 as noted. Besure interior 17-004-6300 is properly installed andsealed at corners. Install new glass. Cut reglazeadaptor (52-019) daylight opening minus 3/8".Install 52-019 seal and reinstall exterior glazingbead (12-514-6300). Reinstall exterior faces.(Refer to details 9 & 10)

(REGLAZING FROM EXTERIOR - SHOWING GLASS BITE)

ANCHOR 3" FROM SIDE OF VERT.

SEALANT & BACKUP

52-035

PLACE (FROM INTERIOR)WEB AFTER HORIZONTAL IS INBOTTOM OF HORIZONTAL TOWEATHERSTRIP POCKET FROMAPPLY SEALANT IN VERTICAL

R.O.

FRAM

E SI

ZE

11 4"

2" 52-016

HORIZONTAL/INSIDE SET

53-000

10

C TO

C

D.L.

O.

634"

42332"

116"

58" 113

32"

(INSIDE SET)

VERTICAL/ INTERMEDIATE HORIZONTAL INTERSECTION

10-379-4200

PRESSURE OF GLAZING BEADSHELD IN PLACE BY BACK52-019 REGLAZE ADAPTOR ISFOR REGLAZING FROM EXTERIOR,BE CUT OFF AT "V" GROOVEHORIZONTAL EXTRUSION MUST

ON GLASS.

(FROM INTERIOR)TO INSTALLING ANY TRIMTO VERTICAL MULLION PRIORTO COMPLETELY SEAL 52-035APPLY A BEAD OF SEALANT

8

(FROM EXTERIOR)HORIZONTAL INTERSECTIONSEALANT AT VERTICAL &

(REGLAZING FROM EXTERIOR)

HORIZONTAL/INSIDE SET

21 2"

@ EACH END10-752-4200

72-944-4152

52-016

C TO

C

9

D.L.

O.D.

L.O.

C TO

C

634"

42332"5

8"

116"

11332"

53-46770-702-4160

52-466

70-881-6300

FIELD INSTALLEDWATER DEFLECTOR70-702-4153

52-035

(AS REQUIRED)

17-004-6300

12-514-6300

52-488

(AS REQUIRED)

52-034 @ VERT.

SEAL BACK SIDEOF 52-035 OR

JOINT

17-004-6300

12-514-6300

52-488

52-035

52-488TRIM COVER

1/4" glazing (52-034) to be sealedsimilar to 52-035.

NOTE:



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S10

AutoCAD SHX Text

R

BELOW, FIELD INSTALLEDSEALANT SIMILAR TO 1" GLAZINGAFTER SLIDING VERT. TOGETHERTO BOTTOM OF UPPER MULLION2 PCS. 16-775-4150 ATTACHED

14

JAMB SPLICE

(1" GLAZING)

AS REQUIREDWITH BACKER RODPERIMETER SEALANT

(1/4" GLAZING)

11

JAMB SPLICE

AS REQUIREDWITH BACKER RODPERIMETER SEALANT

FIELD INSTALLED

NON HARDENING

EXPANSION MULLION SPLICE

(1" GLAZING)

NON HARDENING

BURIED IN SEALANT

(1/4" GLAZING)

EXPANSION MULLION SPLICE

(1" GLAZING)

VERTICAL SPLICE

15

FIELD INSTALLED

NON HARDENING

FIELD INSTALLED

GUTTER SPLICE16-775-4150

NON SKINNING

SEALANT

SEALANT

FIELD INSTALL10-241-4200

16

SEALANT

NON SKINNING

FIELD INSTALL10-241-4200

VERTICAL SPLICE

(1/4" GLAZING)

53-470-4150SPLICE

12

NON HARDENING

BURIED IN SEALANT

SEALANT

NON SKINNING

53-471-4150SPLICE

13

SEALANT

NON SKINNING

OF PROPER SIZETO BE COMPLETELY

FIELD INSTALLED

TO BE COMPLETELYOF PROPER SIZE

FIELD INSTALLED

BACKER ROD

SPLICE53-470-4150

BACKER ROD

53-471-4150SPLICE



TMW 453

JUNE 2019


S11

AutoCAD SHX Text

R

1"

FIELD INSTALLED

12-302-XX50

(1" GLAZING)

CORNER SPLICE

CORNER ASSEMBLY

(1/4" GLAZING)

CORNER SPLICE

BACKER ROD OFPROPER SIZE TOBE COMPLETELYBURIED IN SEALANT

20

17

1 2"

FACE SPLICE

19

AFTER ASSEM. 10-377-4200NEAR TOP & BOTTOM REMOVEATTACHING 52-009 ONE (1)BOLT USED AS HANDLE IN10-311-4200 TEMP. ASSEMBLY

52-472-4150

FIELD INSTALLED

10-241-4200FIELD INSTALLED

SEALANT

NON SKINNINGNON HARDENING

SPLICE

134"

SEALANTNON HARDENINGNON SKINNING

18

SEALANT FULL LENGTHFILL THIS VOID WITH

OF CORNER

278"

FIELD INSTALLEDMULLION SPLICE

FIELD INSTALLEDTEK SCREW10-241-XX00

TYPICAL SPLICE

334"

1 4"

FIELD INSTALLED

FIELD INSTALLED

SPLICEC MULLIONL

2"

10-241-4200

52-472-4150SPLICE

34"



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S12

AutoCAD SHX Text

R

53-468

53-500

EXPANSION VERTICAL SIMILAR

VERTICAL/INTERIOR SET HORIZONTAL


VERTICAL/EXTERIOR SET HORIZONTAL

LEAVE 1/2" GAP12-514-6300

VERTICAL FOR WEEPAGEAT CENTER LINE OF

ERECTION BROCHURESSEALANT ANDTMW 453SHOWN INVERTICAL ASTO SIDE OFMUST BE SEALED52-486

22

21

VERTICAL FOR WEEPAGEAT CENTER LINE OFLEAVE 1/2" GAP12-514-6300

53-468

52-481

TO SIDE OF VERTICAL (ABOVE & BELOW

LINE OF VERTICAL. INSTALL BEFORE SETTING GLASS.SHELF OF EACH HORIZONTAL & BUTT TOGETHER AT CENTER52-050-4150 WATER DAM APPLY TO BOTTOM OF GLASS

MAYBE CONTINUOUS PAST VERTICAL OR12-514-6300 WEATHERSTRIP/ISOLATOR

BUTTED TIGHT AT CENTER LINE OF VERTICAL.

OF HORIZONTAL GLASS SHELF. THIS AREA MUST BE SEALED SOOF WATER DAMS & COMPLETELY SEAL TOP OF GLASS TO BOTTOM

THAT NO WATER CAN FLOW INTO ENDS OF HORIZONTAL. WEEPAGEMUST FLOW DOWN EXTERIOR OF VERTICAL 1/2" SILICONE JOINT.

1/2" SILICONE JOINT WEATHERSEAL MUST CONTINUE TO BOTTOM

COMPLETELY SEAL WATER DAMS TOHORIZONTALS & FRONT OF VERTICAL.

GLASS SHELF) IN GLASS POCKET AREA.

FILL ALL VOIDS

FROM EACH END OF RETAINERBY USING A 10-752-4200 FASTENER 3"RETAINERS TO BE SECURED TO HORIZONTALS

COMPLETELY SEAL END OF HORIZONTAL

TO SIDE OF VERTICAL IN GLASS

adaptor is installed.

When 53-518 horizontal is used with

1/4" glass in top light, setting block

shelf must be installed before 1/4"

MUST FLOW DOWN EXTERIOR OF VERTICAL 1/2" SILICONE JOINT.THAT NO WATER CAN FLOW INTO ENDS OF HORIZONTAL. WEEPAGEOF HORIZONTAL GLASS SHELF. THIS AREA MUST BE SEALED SOOF WATER DAMS & COMPLETELY SEAL TOP OF GLASS TO BOTTOM1/2" SILICONE JOINT WEATHERSEAL MUST CONTINUE TO BOTTOM

BUTTED TIGHT AT CENTER LINE OF VERTICAL.MAYBE CONTINUOUS PAST VERTICAL OR12-514-6300 WEATHERSTRIP/ISOLATOR

HORIZONTALS & FRONT OF VERTICAL.COMPLETELY SEAL WATER DAMS TO


VERTICAL/SILICONE HORIZONTAL

HORIZONTAL & BUTT TOGETHER ATTO BOTTOM OF GLASS SHELF OF EACH70-702-4153 WATER DEFLECTOR APPLY

CENTER LINE OF VERTICAL

POCKET AREA. FILL ALL VOIDS

COMPLETELY SEAL HORIZONTAL

23

52-481

53-518

53-000

FILL ALL VOIDS

GLASS SHELF) IN GLASS POCKET AREA.TO SIDE OF VERTICAL (ABOVE & BELOWCOMPLETELY SEAL END OF HORIZONTAL

NOTE:

53-518

53-450



TMW 453

JUNE 2019


S13

AutoCAD SHX Text

R

AT SILL - INSIDE SET:

SILL NOTE:

12-514-6300 weatherstrip/isolator may be continuouspast vertical or butted tight at center line of vertical (top& bottom).

12-514-6300 weatherstrip/isolator may be continuouspast vertical or butted tight at center line of vertical attop, at bottom leave a 1/2" gap in 12-514-6300 atcenter line of vertical.

52-000 retainer should be attached in place with a10-752-4200 screw at each end of retainer to preventretainer from being knocked off during installation ofglass.

fastener 3" from each end of retainer.

Retainers (53-000) to be secured to

horizontals by using a 10-752-4200

should seal to 12-514-6300 at head & seal.

Vertical weatherstrip joint between glass


VERTICAL/SILL

VERTICAL RUNNING THRU

VERTICAL/INTERIOR SET HEAD


BE REMOVED AND VOID SEALED WITH SILICONE.AT THE END OF THIS TIME THEY ARE TO BEIN PLACE WHILE STRUCTURAL SILICONE IS CURING.(TWIST IN PLACE) THESE TEMPORARIES MUST BE LEFT88-088-5100 TEMPORARY GLASS HOLDER 2'-0" OC.

(NOT BY PITTCO)WEATHERSEAL SILICONE

(NOT BY PITTCO)DENVER FOAM BACK-UP

GLASS IS IN PLACE.BY PITTCO) APPLY AFTERSTRUCTURAL SILICONE (NOT

12-916-6300 BACK-UP

TYPICAL VERTICAL SHOWING

INTERMEDIATE HORIZONTAL SIMILAR


GLASS/SILICONE JOINT

WIDTH OF VERTICAL ISOF HORIZONTAL SO THATCAP APPLY TO BOTTOM70-702-4160 END

COVERED.

RETAINER NOTE:

53-000

26

53-454

52-481

HORIZONTAL RUNNING THRU

(STOPS ATOP

HOLE AT CENTER LINEDRILL 3/8" MINIMUM

53-454

HORIZONTAL)

OF VERTICAL FOR WEEPAGE

25

VERTICAL/SILL

HEAD NOTE:

53-518

HORIZONTAL FILL ALL VOIDSEND OF VERTICAL TOCOMPLETELY SEAL FRONT

12-514-6300

53-000

NOTE:

24

VERTICAL JOINT IN 53-000.OF VERTICAL ALSO SEALFILL ALL VOIDS AT FRONT

TO ENDS OF HORIZONTALSCOMPLETELY SEAL END CAP

53-000

12-514-6300

53-467

& FRONT OF VERTICAL.

52-481

53-500

VOIDS AT FRONT OF VERTICAL.FRONT OF VERTICAL. FILL ALLTO ENDS OF HORIZONTALS &COMPLETELY SEAL END CAP

TOP OF WEATHERSTRIP POCKETSIDE OF VERTICAL BEGINNING ATHORIZONTAL MUST BE SEALED TO

12-514-6300

AREA.

TO BOTTOM OF VERTICAL

VERTICAL IN GLASS POCKETBE SEALED TO SIDE OFLEG OF HORIZONTAL MUSTTHIS SMALL VERTICAL

ERECTION BROCHUREIN TMW 453 SEALANT &OF VERTICAL AS SHOWNMUST BE SEALED TO SIDE52-486 (SHOWN DOTTED)

THAT WIDTH OF VERTICAL ISTO TOP OF HORIZONTAL SO70-702-4160 END CAP APPLY

AS REQUIRED.

COVERED.

WITH BACKER RODPERIMETER SEALANT

52-481

2. All sealants that contact silicone sealants must be compatible.

1. All glass and metal must be clean and dry before applying any sealants.

NOTES:



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S14

AutoCAD SHX Text

R

SECURED TO HORIZONTALS BY

USING A 10-752-4200 FASTENER

3" FROM EACH END OF RETAINER

SECURED TO HORIZONTALS BY

USING A 10-752-4200 FASTENER

3" FROM EACH END OF RETAINER

SILICONE WEATHERSTRIP JOINT

CENTER LINE OF 1/2" VERTICAL

DRILL 3/8" MINIMUM HOLE AT

STOP SHORT OF WEEP HOLE.

BOTTOM 12-514-6300 MUST

52-046

BOTTOM OF WEATHERSTRIP POCKET

GLASS POCKET, BEGINNING AT

SEALED TO SIDE OF CORNER IN

HORIZONTAL MUST BE COMPLETELY

AREA. FILL ALL VOIDS AT END

OF CORNER IN GLASS POCKET

ENDS OF HORIZONTAL AND END

COMPLETELY SEAL END CAP TO

CORNER IS COVERED AS SHOWN.

HORIZONTAL SO THAT END OF

MITER AND APPLY TO TOP OF

70-702-4160 END CAP FIELD

RETAINERS (53-000) TO BE

PERIMETER SEALANT.

FOR WEEPAGE

END OF 52-046 WITH

53-000 RETAINER

DO NOT COMPLETELY PLUG

CORNER AND BUTT TIGHT.

WEATHERSTRIP/ISOLATOR AT

MITER TOP 12-514-6300

TO TOP OF HORIZONTAL.

OF CORNERS.

RETAINERS (53-000) TO BE

CORNER IS COVERED AS SHOWN.

70-702-4160 END CAP FIELD

MITER AND APPLY TO BOTTOM OF

HORIZONTAL SO THAT END OF

90 DEG. CORNER/SILL HORIZONTAL

90 DEG. CORNER/HEAD HORIZONTAL

135 DEG. CORNER SIMILAR

28


52-040

27

52-540

GLASS POCKET, BEGINNING AT

TOP OF WEATHERSTRIP POCKET

53-454

52-481

TO BOTTOM OF HORIZONTAL.

HORIZONTAL MUST BE COMPLETELY

SEALED TO SIDE OF CORNER IN

COMPLETELY SEAL END CAP TO

ENDS OF HORIZONTAL AND END

OF CORNER IN GLASS POCKET

AREA. FILL ALL VOIDS AT END

OF CORNERS.

PERIMETER SEALANTWITH BACKER RODAS REQUIRED.

52-481

53-454

can not be interior set.90 deg. & 135 deg. outside silicone cornersNOTE:



TMW 453

JUNE 2019


S15

AutoCAD SHX Text

R

STOP BOTTOM 12-514-6300

BUTT TIGHT TO SIDE OF 52-046APPLY TO BOTTOM OF GLASS SHELF.70-702-4153 WATER DEFLECTOR

90 DEG. CORNER/52-466 HORIZONTAL

90 DEG. CORNER/EXTERIOR SET HORIZONTAL

USING A 10-752-4200 FASTENER3" FROM EACH END OF RETAINER

CORNER, FILL ALL VOIDS.

AGAINST 52-046SHELF AND BUTT TIGHTAPPLY TO BOTTOM OF GLASS52-050-4150 WATER DAM

TO HORIZONTAL AND FRONT OFCOMPLETELY SEAL WATER DAM

CORNER AND BUTT TIGHT.WEATHERSTRIP/ISOLATOR ATMITER TOP 12-514-6300

RETAINERS (53-000) TO BESECURED TO HORIZONTALS BY


30


29

AT END OF HORIZONTAL

FRONT OF CORNER, FILL ALL VOIDS.

MITER TOP 12-514-6300

TO END OF HORIZONTAL ANDCOMPLETELY SEAL WATER DAM

CORNER AND BUTT TIGHT.WEATHERSTRIP/ISOLATOR AT

RETAINER53-000

52-540

AT END OF HORIZONTALSTOP BOTTOM 12-514-6300

52-488

52-035

52-019

52-466

53-468

POCKET, INCLUDING THESE POCKETS.CONTINUE TO BOTTOM WEATHERSTRIPAT TOP WEATHERSTRIP POCKET &IN GLASS POCKET AREA. BEGIN(ABOVE & BELOW GLASS SHELF)HORIZONTAL TO SIDE OF CORNERCOMPLETELY SEAL END OF

NOTE:

1/2" vertical silicone joint weatherseal mustcontinue to bottom of water deflector andcompletely seal top of glass to bottom ofhorizontal shelf. Same as at typical vertical.



TMW 453

JUNE 2019

TMW 453

JUNE 2019


S16

AutoCAD SHX Text

R

DENVER FOAM ROD STOCK BEFORESTUFF ENDS OF "ADAPTOR" WITH

EXPANSION VERTICAL MULLION

EXPANSION JOINT 1" GLASS

TYPICAL VERTICAL MULLION

32

1" INSULATED GLASS

STRUCTURAL SILICONE

52-506

31

1" INSULATED GLASS

1" GLASS JOINT.)SILICONE SEALANT. (SIMILAR TOFILLING EXPANSION JOINT WITH

EXPANSION JOINT

1" GLASS

52-481

STRUCTURAL SILICONE

EXPANSION JOINT 1" GLASS

90 DEG. OUTSIDE CORNER

GLASS TO MULLIONS).AS USED TO BONDSEALANT (SAME SILICONESTRUCTURAL SILICONEJOINT VOIDS WITHFILL ALL EXPANSION

52-040, FILL ALL VOIDS.WITH SILICONE AT SPLICE IN53-500 & 52-009 AND FILLSTUFF VOIDS BETWEEN 52-040,

33

TO BOND GLASS TO MULLION).SEALANT (SAME SILICONE AS USEDVOIDS WITH STRUCTURAL SILICONEFILL ALL SPLICE (EXPANSION) JOINT

52-540

MULLION SPLICE)DIRECTLY ABOVE CORNERLINE OF HORIZONTAL FACEJOINT TO OCCUR AT CENTER52-046 (CORNER FACE SPLICE

SPACER GASKETSTOP AT EXPANSION

53-521-4150

12-916-6300

SPLICE

VERTICALEXPANSIONJOINT

JOINT

53-507

1/4" GLASS

EXPANSION JOINT

SPACER GASKET

OCCUR 1 1/2" MIN.

52-040 VERTICAL

HEADS IN THISSEAL ALL BOLT

MULLION SPLICE

AREA.

JOINT.

BELOW CORNER

SPLICE JOINT TO

52-040 SPLICELOCATION ASSTOPS AT SAME

JOINT.

1" INSULATED

12-916-6300

SILICONESTRUCTURAL

GLASS


(SAME SILICONE AS USED TO BONDWITH STRUCTURAL SILICONE SEALANTFILL ALL EXPANSION JOINT VOIDS

12-916-6300 SPACER GASKET

GLASS TO MULLIONS).

JOINTEXPANSIONVERTICAL

53-520-4150 SPLICE

STOP AT EXPANSION JOINT

53-500


(SPLICE JOINT)

52-540

SPLICE52-522-4150

MULLION LOCK52-009 CORNER

Horizontal should occur within

36" of splice joint shown below.

JOINT

VERTICALEXPANSION

NOTE:

Also a continuous bead of sealant must be applied between

135 deg. outside corner similar except 52-022 outside trimhas splice joint at same location as 52-542 mullion.

52-542 halves.

NOTE:



TMW 453

JUNE 2019


S17

AutoCAD SHX Text

R

of sealant as requiredApply small bead

FINAL POSITION

1 7/8"POCKET

GLASS

CONTACT

"W" SIDE BLOCKS

19-1

83

19-0

45

FIG. 2

SLIDE BETWEEN REGLETFLATTEN BLOCK &

AND GLASS LITE.

STRETCH

INSERT BETWEENGLASS & FRAME.

work towards centerStart at ends and

Horizontal Gasket

Gasket = Approximately

runs through

D.L.O. + 1/2"

FIG. 1*Notes:1. Glazing Adaptors 19-045 & 19-183 are provided for applicationsrequiring infills less than 1" in thickness (See Glazing Chart). Theseadaptors are designed to be inserted into the reglet, and they must beinserted after installation of frame so sealing procedures can beaccomplished at joint.

2. Horizontal to vertical joints of adaptors should be sealed afterinstallation.

One "W" Side Block (12-908-6350 or 12-908-6351)should be installed into the deep pocket of the mullion ofeach light of glass to prevent shifting of the glass in theopening. (See FIG. 2)

NOTE: If deglazing of lite is required after "W" Block is installed, remove both interior and exterior weathering and use hook to pull "W" Block out of the pocket.

"W" Block (12-908-6350 or 12-908-6351) will expandand wedge between walls of glazing pocket and preventglass from shifting into deep pocket.

12-908-6350or

12-908-6351



TMW 453

JUNE 2019

SECTION 5 - Glazing

G1

AutoCAD SHX Text

R

TMW GlazingGlass

ThicknessExteriorGasket

InteriorGlasket

PocketAdaptor

1/8" 12-522 17-012 19-0453/16" 12-514 17-012 19-0451/4" 12-514 17-004 19-0455/16" 12-514 17-013 19-0453/8" 12-521 17-013 19-0451/2" 12-522 17-012 19-1839/16" 12-514 17-012 19-1835/8" 12-514 17-004 19-183

11/16" 12-514 17-013 19-1833/4" 12-521 17-013 19-1837/8" 12-522 17-012 None

15/16" 12-514 17-012 None1' 12-514 17-004 None

1 1/16" 12-514 17-013 None1 1/8" 12-521 17-013 None

System designed for maximum 1 1/8" glazing

GLASS SIZE FORMULA

Daylight Opening

Daylight Opening + 1"

12" 1

2"

Dayl

ight

Ope

ning

Dayl

ight

Ope

ning

+ 1

"

1 2"1 2"



TMW 453

JUNE 2019

TMW 453

JUNE 2019

SECTION 5 - Glazing

G2

AutoCAD SHX Text

12-908-6350

AutoCAD SHX Text

12-908-6350

AutoCAD SHX Text

70-881

AutoCAD SHX Text

70-881

AutoCAD SHX Text

70-881

AutoCAD SHX Text

70-881

AutoCAD SHX Text

12-908-6351

AutoCAD SHX Text

R

TMW 453 FABRICATION - SEALANT - ERECTION R

Documents

Transcript of TMW 453 FABRICATION - SEALANT - ERECTION R