69

R

SPECIFICATION:Rotor Size: Ø860mm x 860mm (Ø34” x 34”)

Net Power: Tier 3 / Stage IIIA: Caterpillar C7.1 Acert 186kW (250hp)

Tier 4F / Stage IV: Caterpillar C7.1 205kW (275hp)

Portability: Tracked

Operating Weight: 33,950kg* (74,847lbs*)

*With side conveyor and twin pole magnet fi tted

I-100RSTM

TEREX FINLAY TELEMATICS SYSTEM

I-100RSIMPACT CRUSHER

70

R

HOPPER / FEEDERHopper capacity: 2.3m³ (3.01yd³)

Feed height: 3.2m (10’ 6”)

Material: 8mm wear resistant steel

Width at rear: 2.26m (7’ 5”)

Vibrating Grizzly feeder (VGF): 3.27m x 800mm (10’ 9” x 32”)

VGF tine aperture: 25mm Standard

VGF wire mesh aperture: 30mm Standard

Speed: variable, 450 - 850 rpm

SPECIFICATION

IMPACT CHAMBERRotor diamater: Ø860mm (34”)

Rotor width: 860mm (34”)

Inlet opening: 860mm x 610mm (34” x 24”)

Rotor speed Range: 700 rpm - 930 rpm

Maximum Feed Size: Dependant on application 350mm Cube Approx

Drive arrangement: Direct drive via clutch

Twin Apron

Maximum apron settings: 120mm Primary, 55mm Secondary

Minimum apron setttings: 40mm Primary, 20mm Secondary

Rotor Confi guration: 4 bar rotor, 2 high / 2 low standard

Hydraulic overload protection

Hydraulic apron setting assist

Blowbar options: Martensitic (standard), Ceramic & High Chrome

POWERPACKTier 3 / Stage IIIA: Caterpillar C7.1 Acert

Engine Power: 186kW (250hp)

Engine Speed: 1700-2100 rpm

Tier 4F / Stage IV: Caterpillar C7.1

Engine Power: 205kW (275hp)

Engine Speed: 1700-2100 rpm

MAIN CONVEYORBelt Width: 900mm (36")

Belt Spec: plain

Working Angle: 22°

Speed: 95 - 110 m/min

Full length main conveyor with impact bars at feed point

Main conveyor can be lowered hydraulically for maintenance

Dust suppression: fi tted with hose and spraybars as standard (no

pump supplied)

Discharge Height: 3.25m (10' 8")

Stockpile capacity: 51m³ (66.7yd³) @ 40°

Hopper

Cat Engine

Main Conveyor

Impact Chamber

Hopper

71

SCREEN BOXTop deck: 2.44m x 1.2m (8’ x 4’)

Tensioning top deck: Side Tension

Drive: Hydraulic Motor

Screen Angle: 20°

Screen Speed: 1100 rpm

Screen can be lowered to a horizontal position for mesh changing and

general service access

Screen and Fines can be quick detached if not required

Total screening area: 32ft2

OVERSIZE TRANSFER CONVEYORBelt width: 500mm (20”)

Belt spec: Plain

Working Angle: 20°

Speed: Adjustable

Hydraulically folds for transport

RE-CIRCULATING CONVEYORBelt width: 500mm (20”)

Belt spec: Plain

Speed: Adjustable

Working Angle: 17°

Hydraulically folds for transport

TANK CAPACITIESHydraulic Tank: 350 litres / 77 UK gal / 92 US gal

Fuel Tank: 400 litres / 88 UK gal / 105 US gal

BY-PASS CONVEYOR - OPTIONALBelt Width: 500mm (20”)

Belt Spec: plain

Working Angle: 25°

Speed: 60 - 70 mpm

Hydraullically folds for transport

Discharge Height: 2.03m (6' 8")

Stockpile capacity: 13.8m³ (18yd³) @ 40°

By-pass ConveyorMAGNETIC SEPERATOR (OPTIONAL)Belt Width: 750mm (30”)

Drum Centres: 1.49m (58”)

Belt spec: cleated

Drive: Hydraulic

Magenetic Seperator

Oversize Transfer Conveyor

Re-circulating Conveyor

Screenbox

I-100RS

72

CONTROL SYSTEMSAdvanced CANBUS compliant system

Large color display screen

Simple operating modes with menu driven graphic user interface

- Track mode: for moving machine

- Manual Mode: for manually starting machine

- Automatic Mode: For automatically starting machine in

predetermined sequence

- Language Mode: To select required language

- Test Mode: to test run individual components

- Engine Diagnostic: showing engine information e.g. hours, rpm, etc.

- Confi guration Mode: For setting individual components

Detachable doglead control for tracking

Radio remote control (optional)

Lockable compartment

Emergency stops: 6 off

Control System

UNDERCARRIAGEShoe Width: 400mm (16")

Sprocket Centres: 3.7m (12' 1")

Track Speed: 0.6 km/h

Gradeability: 25°

CHUTESHeavy duty inlet chute with bolt-up construction, and liner plates

By-pass chute with selectable discharge fl op gate, to either by-pass

conveyor or main conveyor

TOOL BOXMounted lockable toolbox

Tool Kit and fl ogging spanners

Grease gun

ManualsUndercarriage

R

Remote Control Unit (Optional)

REMOTE CONTROL UNIT (OPTIONAL)Full function radio remote unit

Machine can be switched from crushing mode into track mode,

moved and be switched back to operating mode from remote control

unit

Primary apron remote hydraulic release

Feeder stop / start

PLATFORMSGalvanised catwalks and ladders for full maintenance and service

access

Catwalks on right hand side

Compact folding for transport

Platforms

73

I-100RS

TM

STANDARD FEATURES

ENGINE:Tier 3 / Stage IIIA: Caterpillar C7.1 Tier 3 ACERT 186kW (250hp)

Engine

Tier 4 Final / Stage IV : CAT C7.1 - 205kW (275hp)

IMPACT CHAMBER:Terex CR004 Impact chamber c/w full hydraulic apron

setting

4 bar rotor - Martensitic blow bars 2 High & 2 Low

Direct Drive via Clutch

Please contact the sales department for blowbar options

HOPPER / FEEDER:Fixed Hopper c/w vibrating feeder

Stepped grizzly feeder with integral pre-screen, standard35mm Tines spacing

Mesh aperture on grizzly feeder: 30mm

MAIN CONVEYOR:Belt width: 900mm (36”)

RS COMPONENTS:8’ X 4’ Single Deck Screen - supplied with 40mm mesh asstandard unless otherwise stated

Fines Conveyor 1.2m belt - hydraulically folding for transport

Transfer Conveyor 500mm belt - Hydraulically folding fortransport

Recirculating Conveyor 500mm Belt - Hydraulically foldingfor transport

Screen, Fines & transfer conveyor can be removed as singlecomponent

AUXILARY CONVEYORS:Piped for overband magnet

CLIMATE SPEC:Standard Oils - (Recommended for ambient temperaturesbetween -5 to +30°C)

DUST SUPRESSION:Piped for dust supression c/w Spraybars

ELECTRICAL:Emergency stops

Hand Held Track Control Set with Connection Lead

T-Link Telemetry System fi tted c/w 3 years data subscription

GENERAL:Safety Guards in Compliance with Machinery Directive

Single Speed Tracks

Optional spacing on grizzly, 35mmTines/46mm Tines/40mmPunch Plate & 60mm Punch Plate

Optional Spacing on Mesh under Grizzly - 10/20/40/50mm

- please specify aperture in additional information area

Belt weigher on main conveyor

Undercrusher vibratory feeder c/w shortened main conveyor

By-pass conveyor- 500mm beltwidth

Twinpole over band magnet (c/w stainless steel skirting &stainless steel discharge chute )

Twinpole heavy duty overband magnet (skirting & chute asabove) (please check leadtime)

Hot climate oils - (Recommended for ambient temperatures

between +15 to +50°C)

Cold climate oils - (Recommended for ambient temperatures

between -20 to +30°C)

Radio remote System

Control Panel Positive Pressurisation

Lighting mast (check leadtime)

Electric Re-Fuelling Kit

Special paint (if different from Finlay Orange RAL2002).

RAL must be specified*

OPTIONAL EQUIPMENT

74

By-Pass Conveyor (Optional) u Belt Width: 500mm (20”)

u Belt Spec: plain

u Working Angle: 25°

u Speed: 60 - 70 mpm

u Hydraullically folds for transport

u Discharge Height: 2.03m (6’ 8”)

u Stockpile capacity: 13.8m³ (18yd³) @ 40°

Main Conveyoru Belt Width: 900mm (36”)

u Belt Spec: plain

u Working Angle: 22°

u Speed: 95 - 110 m/min

u Full length main conveyor with impact bars at feed point

u Main conveyor can be lowered hydraulically for maintenance

u Dust suppression: fi tted with hose and spraybars

as standard (no pump supplied)

u Discharge Height: 3.25m (10’ 8”)

u Stockpile capacity: 51m³ (66.7yd³) @ 40°

Hopper / Feederu Hopper capacity: 2.3m³ (3.01yd³)

u Feed height: 3.20m (10’ 6”)

u Material: 8mm wear resistant steel

u Width at rear: 2.26m (7’ 5”)

u Vibrating Grizzly feeder (VGF):

3.27m x 800mm (10’ 9” x 32”)

u VGF tine aperture: 25mm Standard

u VGF wire mesh aperture: 30mm Standard

u Speed: variable, 450 - 850 rpm

Re-Circulating Conveyor u Belt width: 500mm (20”)

u Belt spec: Plain

u Working Angle: 17°

u Speed: Adjustable

u Hydraulically folds for transport

Screen Boxu Top deck: 2.44m x 1.2m (8’ x 4’)

u Tensioning top deck: Side Tension

u Drive: Hydraulic Motor

u Screen Angle: 20°

u Screen Speed: 1100 rpm

u Screen can be lowered to a horizontal position for

mesh changing and general service access

u Screen and Fines can be quick detached if not required

u Total screening area: 32ft2

Oversize Transfer Conveyor u Belt width: 500mm (20”)

u Belt spec: Plain

u Working Angle: 20°

u Speed: Adjustable

u Hydraulically folds for transport

Impact Chamberu Rotor diamater: Ø860mm (34”)

u Rotor width: 860mm (34”)

u Inlet opening: 860mm x 610mm (34” x 24”)

u Rotor speed Range: 700 rpm - 930 rpm

u Maximum Feed Size: Dependant on application

350mm Cube Approx

u Drive arrangement: Direct drive via clutch

u Twin Apron

u Maximum apron settings: 120mm Primary, 55mm Secondary

u Minimum apron setttings: 40mm Primary, 20mm Secondary

u Rotor Confi guration: 4 bar rotor, 2 high / 2 low standard

u Hydraulic overload protection

u Hydraulic apron setting assist

u Blowbar options: Martensitic (standard), Ceramic

& High Chrome

Powerpacku Tier 3 / Stage IIIA: Caterpillar C7.1 Acert

Engine Power: 186kW (250hp)

Engine Speed: 1700-2100 rpm

u Tier 4F / Stage IV: Caterpillar C7.1

Engine Power: 205kW (275hp)

Engine Speed: 1700-2100 rpm

Undercarriageu Shoe Width: 400mm (16”)

u Sprocket Centres: 3.7m (12’ 1”)

u Track Speed: 0.6 km/h

u Gradeability: 25°

75

I-100RS

WORKING DIMENSIONS

MACHINE WEIGHT:

TRANSPORT DIMENSIONS

15.8m (51’ 9”)

14.8m (48’ 7”) 3m (9’ 10”)

3.2m

(10

’ 6”)

33,950kg* (74,847lbs*) *With side conveyor and twin pole magnet fi tted

5.5m (18’)

3.86

m (

12’ 8

”)

For further information on specifi c machine weight confi gurations please consult Terex Finlay

76

R

www.terexfi nlay.com

Effective June 2014. Product specifi cations and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only.

Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when using our equipment or to otherwise

act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex GB

Ltd. makes no other warranty, express or implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and

other countries. All rights are reserved. Terex® is a registered trademark of Terex Corporation in the USA and many other countries. Copyright 2010 Terex GB Ltd.

Follow us on: