Thin Film Deposition Prof. Dr. Ir. Djoko Hartanto MSc Electrical Engineering Department Faculty of...
Transcript of Thin Film Deposition Prof. Dr. Ir. Djoko Hartanto MSc Electrical Engineering Department Faculty of...
Thin Film DepositionThin Film Deposition
Prof. Dr. Ir. Djoko Hartanto MScProf. Dr. Ir. Djoko Hartanto MSc
Electrical Engineering DepartmentFaculty of Engineering University of Indonesia
February 14, 2003
IntroductionIntroduction
The need of layers of semiconductor, dielectrics, and conductors to complete the device
Beside the circuits have shrunk, they also have grown in the vertical direction.– Through increased numbers of deposit layers.
OverviewOverview
List of common deposition systems
Atmospheric Pressure (AP)1. Horizontal
2. Vertical
3. Barel
4. Vapor phase epitaxy
List of common deposition systemsList of common deposition systems
Low Pressure (LP) and
Ultra High Vacuum (UHV)
1. Horizontal
2. Vertical
3. Barel
4. Vapor phase epitaxy
OverviewOverview
There two primary techniques for layer deposition :
1. Physical Vapor Deposition (PVD)
2. Chemical Vapor Deposition (CVD)
Physical Vapor Deposition (PVD)Physical Vapor Deposition (PVD)Physical vapor deposition (PVD) refers to a
family of processes in which a material is converted to its vapor phase in a vacuum chamber and condensed onto a substrate surface as a thin film.
PVD can be used to produce coatings of a wide variety of materials: metals alloys ceramics glasses semiconductors polymers
Physical Vapor Deposition (PVD)Physical Vapor Deposition (PVD)
All PVD processes consist of the following steps: synthesis of coating vapor, vapor transport to the substrate, condensation of vapors onto the substrate
surface to form a thin film. These steps are carried out inside a vacuum
chamber, so evacuation of the chamber always precedes the PVD process.
Physical Vapor Deposition (PVD)Physical Vapor Deposition (PVD)
Pressure Units: 1 atm = 14.7 psia = 29.92 inches Hg = 760 mm Hg = 760 torr = 1.013 bar = 1.013 x 105 Pa
1 Pa = 1 N/m2 = 7.5 x 10-3 torr
Physical Vapor Deposition (PVD)Physical Vapor Deposition (PVD)The two most common PVD processes are: evaporation sputtering
We have already covered the basics of evaporation.
For evaporation, the background pressure in the vacuum chamber is typically ~10-6 Torr (~10-4 Pa) or lower.
For sputtering, the background pressure in the vacuum chamber is typically 10-3 to 10-2 Torr (~1 Pa).
EvaporationEvaporation
In order to evaporate a material, it must be heated to a temperature at which its vapor pressure is 10-3 Torr or higher.
E.g., aluminum must be heated to 1000°C or more.
EvaporationEvaporation
There are two common ways to heat the source material : resistive heating electron-beam heating.
Resistive heating uses electric current flow through a tungsten filament to heat the source material.
The source material can be placed directly on the tungsten filament, or it can be put in a crucible that is heated by the filament.
EvaporationEvaporation Evaporation from a filament-heated crucible.
Aluminum Vapor
Aluminum Film
Silicon Wafer
EvaporationEvaporation In electron-beam (e-beam) evaporation systems,
a high intensity beam of electrons, with energy up to 15 keV, is focused on the source material.
Electron bombardment heats the source material to the temperature required for evaporation.
Heating can be restricted to the source material itself . The surroundings stay cool.
Because pressure is so low in the vacuum chamber, in evaporation the source material travels in a straight line from the source to the substrate shadowing
Physical Vapor Deposition (PVD)Physical Vapor Deposition (PVD)The mean free path, of atoms or molecules in
a chamber at pressure P is given by
T is the absolute temperature, k is Boltzmann’s constant, and d is the diameter of the gas atoms or molecules
The mean free path is the average distance between collisions in the chamber.
2dP2
kT
Physical Vapor Deposition (PVD)Physical Vapor Deposition (PVD) At room temperature and for a typical atom/molecule
diameter of 4 Å, the previous equation becomes
The pressure P is in pascals (Pa). 1 Pa = 1 N/m2 = 7.5 10-3 Torr What is the mean free path for typical evaporation and
sputtering conditions?
)(108.5 3
mP
SputteringSputtering
In sputtering, the source material is usually in the form of a sheet or plate, called a target.
Sputtering is achieved by bombarding the target with energetic ions, typically Ar+.
Atoms on the surface of the target are dislodged by this bombardment and fly off .
These atoms then impinge on the substrate, resulting in deposition of a thin film.
Chemical Vapor DepositionChemical Vapor Deposition
Chemical Vapor Deposition (CVD) is the formation of a solid material (insulator, metal, or semiconductor) from the reaction of source gases (or vaporized liquids).
The solid material is usually in the form of coating (a “thin film”) 20-5000nm thick (200-50,000Å or 0.02-5m).
CVD of Zinc Oxide (ZnO)CVD of Zinc Oxide (ZnO)A simple Chemical Vapor Deposition system for
the preparation of thin film coatings of ZnO on a substrate (e.g., a Si or GaAs wafer) is shown:
Exhaust
N2 + H2O +
Zn(OOCCH3)2
Air
Furnace
Wafer
Chemical Vapor DepositionChemical Vapor Deposition
Materials deposited by CVD are usually amorphous or polycrystalline.
If a “clean” crystalline substrate is used, it can sometimes act as a seed, resulting in a single crystal deposited layer.
A crystalline layer deposited on a crystalline substrate is called an epitaxial layer.
Chemical Vapor DepositionChemical Vapor Deposition
Examples in microelectronics -- insulators (dielectrics)
Silica (SiO2) deposition (400-500ºC)
SiH4 + O2 SiO2 + 2H2
Silicon Nitride (Si3N4) deposition (700-800ºC)
3SiH4 + 4NH3 Si3N4 + 12H2
LPCVD SystemsLPCVD Systems