THE OLDAKER DIFFERENCE - Test Leads Catalog.pdf · the oldaker difference . if you have a need for...
Transcript of THE OLDAKER DIFFERENCE - Test Leads Catalog.pdf · the oldaker difference . if you have a need for...
THE OLDAKER DIFFERENCE .
IF YOU HAVE A NEED FOR ANY SPECIAL LEADS OR CABLES THAT ARE NO LONGER AVAILABLE FROM THE MANUFACTURER, OR IF YOU HAVE A NEW DESIGNYOU NEED MADE. LET OLDAKER DISTRIBUTORS HELP. CHECK FROM OUR LIST OF CAPABILITIES.
* CUSTOM DESIGN AND MANUFACTURING OF TEST LEADS OR WIRING DEVICES.* ASSEMBLY OF COMPLEX UNITS, BOTH ELECTRICAL & MECHANICAL.* PACKAGING.* RESISTANCE SOLDERING.
* 5 INJECTION MOLDING MACHINES (.5 TO 3 OZ.) BOTH HORIZONTAL & VERTICAL WITH SHUTTLE TABLES.* AUTOMATIC WIRE CUTTING & STRIPPING.* LIGHT PUNCH PRESSES.* LATHES.* HANDSCREW MACHINES.* DRILL PRESSES.* BANDSAWS.* AUTOMATIC SCREW MACHINES, (SINGLE & 5 SPINDLE).* MILLING MACHINES.* WELDING EQUIPMENT (ELECTRIC & GAS).* SHEET METAL SHEARS.* BEND BRAKES.
STAINLESS STEELETHREADED NEEDLETIP WITH POLISHED
POINT
TAPEREDSTRAINRELIEF
HEAVY DUTY WIRE20,000 VOLTS BREAKDOWN
5,000 VOLTS WORKING.
MOLDED FLAMERETARDANT
PLASTIC WITHSAFETY RING
ACCESSORIES ARERECESSED FORADDED SAFETY
NICKLE PLATEDTHREADEDBRASS TIP
9 LEAF SPRINGFOR ADDEDCONTACTSURFACE
HEAVY DUTY WIRE20,000 VOLTS BREAKDOWN
5,000 VOLTS WORKING.
MOLDED FLAMERETARDANT
PLASTIC WITHSAFETY RING
ACCESSORIES ARERECESSED FORADDED SAFETY
THE WIRE DIFFERENCE
THE PROBE DIFFERENCE
VALUE ADDED FROM OLDAKER DISTRIBUTORS
MACHINE CAPABILITIES INCLUDE :
506
OLDAKER MFG. CORP.301 NORTH MAIN ST.DUNKIRK OHIO 45836TEL : (419) 759-3551 FAX : (419) 759-3312
E-MAIL : [email protected]
SPECIAL CAPABILITIES INCLUDE :
THE REPLACEMENT SAFETY SERIESTHE NEEDLE TIP SAFETY SERIES
Notice the wire shown on the left, which is used on our test leads, has many more strands than the wire shown on the right. The difference enables our wire to carry more current and amps safely, and is not easily broke. Also the wire we use has EDPM Rubber insulation which stays more consistent in different temperature ranges, the other wire uses PVC insulation which becomes very stiff in cooler temperatures. Oldaker standard lead length is 4' most others are 2' to 3'.
OLDAKER WIRE THE “OTHER” WIRE
Notice the probes on the right use tips that are all nickel plated brass with small safety rings, all accessories, if any, must slide onto the small .080" diameter pin, which is not safe or secure. Oldaker probes (Shown on the left) use stainless steel needle tips with very sharp polished points for piercing insulation and sure contact, the tips are threaded so all accessories can be securely attached to the tip for better contact and safety. Also the tips are recessed so that the area where the accessory connects to the probe tip is inside the probe to prevent the user from shock. The material used for the probe is ABS, V094 Flame Retardant plastic. The safety rings are 3/4" and well positioned on the probe to keep the user from the exposed tip.
OLDAKER PROBE THE “OTHER” PROBE
Oldaker "TEST WITH THE BEST"
PAGE 3
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
INFORMATION
All Oldaker products are guaranteed, claims of defective material must be made within 10 days of shipment. . .
All products are shipped in zip polybags or plastic pouch.
Oldaker will not be liable for damages, loss or expenses arising in connection with the sale, resale, use of,or the inability to use its products for anything other than its purpose. . .
Any products to be returned must be authorized by Oldaker or Oldaker Distributors.
IF YOU DON'T SEE IT IN THE OLDAKER CATALOG. ASK FOR IT FROMYOUR OLDAKER DISTRIBUTOR. WE MAY BE ABLE TO HELP.
FOR A COMPLETE UP TO DATE CROSS REFERENCECHECK OUR WEBSITE AT www.testleads.net.
PRODUCT INDEX
ACCESSORIES 10 13 15 18 19 20
ADAPTORS & ADAPTOR LEADS 13 20 24
BNC LEADS 7 8 15 16 17
BREAKOUT LEADS 15 16
BULK WIRE & CABLE 26
CLIP LEADS 11 12
CLIPS 15 18 19 20 21
COIL CORD TEST LEADS 5 13 26
CONNECTORS 23 24
DOUBLE PLUG ADAPTORS 16 17 24
FLEXIBLE PROBE TEST LEADS 5
FUSE HOLDER 24
FUSED TEST LEADS 6
HOOK LEADS 8 9 11 13 16
HOOKS 15 21 22
JUMPER LEADS 7 14 15
LEAD BENDER 24
LEAD HOLDER 10
MICRO ADAPTORS 8 13 15
MINIATURE TEST LEADS 4 8 10 13
PART NUMBER INDEX 27
PLUGS & JACKS 22 23 24
PROBES 6 7 8 9 10 18 23 24
PROBE TIPS 24
RETRACTABLE TEST LEADS 6
SCOPE PROBES 25
SHORTING PLUG 24
SILICONE TEST LEADS 5 6 8 9
SOLDERING ACCESSORIES 25
SPECIALTY LEADS 7 10 13 16
STACKABLE TEST LEADS 11 13 14
TELEPHONE STYLE LEADS & ACCESSORIES 11 19 20
TEST LEAD KITS 6 7 8 9 10 22
TEST LEAD SETS 4 5 6 10
NEEDLE TIP SERIESSAFETY LEAD
The TIP on this lead is made of .080" Dia. X 5/8" long stainless steel with a polished point for insulation piercing. Threaded 8-32 for attachments. (Nickel plated).The PROBE is 5" molded flame retardant ABS plastic with 3/4" safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 4 feet, Sold as Sets 1 Red and 1 Black.
PART NUMBER AND OTHER PLUG STYLES.
PART NUMBER AND OTHER PLUG STYLES.
RATED 1,000 VOLTS 10 AMPS
RATED 1,000 VOLTS 10 AMPS
The TIP on this lead is made of .080" Dia. X 1/2" long brass tip threaded 8-32 for attachments. (Nickel plated). . .The PROBE is 4" molded flame retardant ABS plastic with 3/4" safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 4 feet, Sold as Sets 1 Red and 1 Black. Includes clips.
518-10
518-6 518-20 518-21 518-22
518-9518-1
519-2
518-2 518-3
519-1
518-11
519
NOTE: MINI LEADS USE 20 ga. WIRE(41 X 36) TINNED COPPER STRANDING.105" DIA. LEAD LENGTH 3.5'
486-16
596 594
582
486-7
581 486-6 486-20 486-21 486-22
486-15
486-5
486-3
513
486-2 486-17
495-1
486-18
476-4
NOTE: MINI LEADS USE 20 ga. WIRE(41 X 36) TINNED COPPER STRANDING.105" DIA. LEAD LENGTH 3.5'
596-5596-6
596-7 586-1 586-20 586-21 586-22
596-4
596-1
596-2597-2 596-3596-8
STANDARD REPLACEMENT SERIESSAFETY LEAD
Oldaker "TEST WITH THE BEST"
THIS LEADINCLUDESTHREADED
CLIPS
THIS LEADINCLUDESTHREADED
CLIPS
THIS LEAD USESNEEDLE TIPS
THIS LEAD USESNEEDLE TIPS
THIS LEAD USESNEEDLE TIPS
PART NUMBER AND OTHER PLUG STYLES.
RATED 1,000 VOLTS 10 AMPSSLIM-LINE SERIES
TEST LEAD
The TIP on this lead is made of .080" Dia. X 5/8" long stainless steel with a polished point for insulation piercing. Threaded 8-32 for attachments. (Nickel plated).The PROBE is 4.25” slim-line .340 dia. molded flame retardant ABS plastic with non slip ribs and no safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working. .Standard length is 4 feet, Sold as Sets 1 Red and 1 Black.
PART NUMBER AND OTHER PLUG STYLES.
RATED 1,000 VOLTS 10 AMPSSLIM-LINE MINI SERIES
TEST LEAD
PAGE 4
The TIP on this lead is made of .080" Dia. X 1/2" long brass tip threaded 8-32 for attachments. (Nickel plated). . .The PROBE is 3” slim-line mini .340" dia. molded flame retardant ABS plastic with non slip ribs and no safety ring. . The WIRE is 20 ga. (41x36) tinned copper stranding, rubber insulation .105" Dia. 10KV breakdown 2KV working.Standard length is 3.5 feet, Sold as Sets 1 Red and 1 Black. Includes clips.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
518-5
STANDARD PLUG
STANDARD PLUG
STANDARD PLUG
518
STANDARD PLUG
STANDARD PLUG
STANDARD PLUG
518-8
STANDARD JACK
STANDARD JACK
STANDARD JACK
MINIRECESSEDPLUG
MINIRECESSEDPLUG
MINI PLUG
MINI PLUG
MINI .105”JACK
MINI .105”JACK
476-15476-16 476-14
MINIRECESSEDPLUG
MINI PLUGMINI .105”JACK
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
.080” PIN PLUG
.080” PIN PLUG #10 LUG
.080” PIN PLUG
.080” PIN PLUG
.080” PIN PLUG
RECESSED STANDARDPLUG
RECESSED STANDARDPLUG
RECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
RECESSEDSTANDARDSHORT PLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
STANDARD JACK
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
RECESSEDSTANDARDPLUG .380”
RECESSEDSTANDARDPLUG .380”
518-7
SLOTTED JACKFITS SIMPSON260 METERS
SLOTTED JACKFITS SIMPSON260 METERS
SLOTTED JACKFITS SIMPSON260 METERS
NEEDLE TIP FLEXIBLE SERIESSAFETY LEADPART NUMBER AND OTHER PLUG STYLES.
PART NUMBER AND OTHER PLUG STYLES.
RATED 1,000 VOLTS 10 AMPS
RATED 1,000 VOLTS 10 AMPS
619 619-20 619-21 619-22
663662 617615-11
774-7 774-6 774-20 774-21 774-22
774-9774-1 774-3774-11
776-2
776-8
776-4 776-3 776-20 776-21 776-22
776 776-6776-1 776-5
NEEDLE TIP FLEXIBLE SILICONE SERIESSAFETY LEAD
Oldaker "TEST WITH THE BEST"
THESE LEADSUSE SILICONE
WIRE
THESE LEADSUSE RUBBER
WIRE
FLEXIBLE PROBE
FLEXIBLE PROBE
6” WIRE LENGTH18 GA. WIRE
12” WIRE LENGTH18 GA. WIRE
PART NUMBER AND OTHER PLUG STYLES.
RATED 1,000 VOLTS 10 AMPSCOIL CORD SERIESTEST LEAD
PART NUMBER AND OTHER PLUG STYLES.2 CONDUCTOR COIL CORD SERIES
TEST LEAD
PAGE 5
The TIP on this lead is made of .080" Dia. X 1/2" long brass tip. Threaded 8-32 for attachments. (Nickel plated). . .The PROBE is 4" molded flame retardant ABS plastic with 3/4" safety ring. . The WIRE is 2 conductors of 24 ga. (21 x 36) tinned copper stranding with .220" O.D. Coil size 5/8" 1 foot retracted 5 foot extended.This lead has 2 wires in one coil and is very useful where there is a need for coil cord but not the tangles (1 coil cord, 2 test leads).
The TIP on this lead is made of .080" dia. X 5/8" stainless steel with a polished point for insulation piercing. Threaded 8-32 for attachments (nickel plated). The PROBE is 5" long molded flame retardant ABS plastic with 3/4" safety ring. . The WIRE is 18 ga. (65x36) neoprene retractable coil cord 1 foot retracted, 5 foot extended. . .These leads are Sold as Sets 1 Red and 1 Black.
The TIP on this lead is made of .080" Dia. X 5/8" long stainless steel with a polished point for insulation piercing threaded 8-32 for attachments. (Nickel plated). . .The PROBE is 5" molded P.V.C. plastic with 3/4" safety ring. . The WIRE is 18 ga. (440x002) copper stranding, SILICONE insulation .145" Dia. -100C to +300c, 20KV breakdown 5KV working.Standard length is 4 feet, Sold as Sets 1 Red and 1 Black.
The TIP on this lead is made of .080" Dia. X 5/8" long stainless steel with a polished point for insulation piercing. Threaded 8-32 for attachments. (Nickel plated). . .The PROBE is 5" molded P.V.C plastic with 3/4" safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, RUBBER insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 4 feet, Sold as Sets 1 Red and 1 Black.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
STANDARD PLUG
774-5
STANDARD PLUG
618
STANDARD PLUG
STANDARD PLUG
774STANDARD PLUG
615
STANDARD PLUG
STANDARD JACK
774-8
STANDARD JACK
664
STANDARD JACK
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
.080” PIN PLUG
774-10
.080” PIN PLUG
665
.080” PIN PLUG
RECESSED STANDARDPLUG
774-2RECESSED STANDARDPLUG
616
RECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
RECESSEDSTANDARDSHORT PLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
STANDARD JACK
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
RECESSEDSTANDARDPLUG .380”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
773-5
773-4
773-7 773-6 773-20 773-21 773-22
773 773-1773-2
STANDARD PLUG
STANDARD PLUG
STANDARD JACK
RECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
SLOTTED JACKFITS SIMPSON260 METERS
620
SLOTTED JACKFITS SIMPSON260 METERS
THIS LEAD USESNEEDLE TIPS
THIS LEAD USESNEEDLE TIPS
THIS LEAD USESNEEDLE TIPS
ADJUSTABLE NEEDLE TIP SERIESSAFETY LEAD PART NUMBER AND OTHER PLUG STYLES.
RATED 1,000 VOLTS 10 AMPS
763-7 763-6 763-20 763-21 763-22
763-3
767-3
763-11
767-10767-9
767-5
767-8
767-7 767-6 767-20 767-21 767-22
767 767-1767-2 767-11
Oldaker "TEST WITH THE BEST"
REPLACEMENT TIP 623-4
PACKAGED INREUSABLE POUCH
PACKAGED INREUSABLE POUCH
KIT INCLUDES, SCREW-ONHOOKS - CLIPS - LUGS
TIP PROTECTORSTIP EXTENSIONS
MODULAR PROBE HANDLEHOUSES 600 VOLT FUSE
(INCLUDED)
REPLACEMENT FUSEPART # 2568-1
SILICONE WIRE
OTHER PLUG STYLES
RETRACTABLETIP COVERS
REPLACEMENT PROBE 763-30 (COLOR)
NOTE : NO ATTACHMENTSCAN BE USED WITH THIS LEAD
PART NUMBER AND OTHER PLUG STYLES.
RATED 1,000 VOLTS 10 AMPS DELUXE SERIESTEST LEAD KIT
PAGE 6
The TIP on this lead is made of .025" Dia. stainless steel with a polished point and is adjustable to 3.5" and is fully insulated to the point.The PROBE is .312" dia. X 5.25" long molded ABS plastic with .385" dia. safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 4 feet, Sold as Sets 1 Red and 1 Black lead.
The TIP on this lead is made of .080" X 5/8" stainless steel with a polished point for insulation piercing, threaded 8-32 for attachments shown above.The PROBE is .312" dia. X 5.25" long molded ABS plastic with .385" dia. safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 4 feet, Sold as Sets 1 Red and 1 Black lead, includes 2 each of the accessories shown above and is packaged in a reusable plastic pouch.
STANDARD PLUG
2568-4STANDARD PLUG
763-5
STANDARD PLUG
STANDARD PLUG
2568-3
STANDARD PLUG
763
STANDARD PLUG
STANDARD JACK
763-8
STANDARD JACK
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
763-10
.080” PIN PLUG
.080” PIN PLUG
763-9.080” PIN PLUG
RECESSED STANDARDPLUG
2568-2
RECESSED STANDARDPLUG
763-2
RECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
763-1
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
2568
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
2568-5
SLOTTED JACKFITS SIMPSON260 METERS
2568 FUSED SAFETY TEST LEAD KIT (600 VOLTS)
This fused safety test lead kit has a replaceable 600 volt fuse housed in each of the probe handles which have a pointed 4 MM plug style tip with retractable tip cover.The PROBE is 4" molded Nylon plastic with safety ring and retractable tip covers. The WIRE is 18 ga. (65x36) tinned copper stranding, SILICONE insulation .145" Dia..Standard length is 4 feet, sold with 600 volt fuses included. Replacement Fuse Part # 2568-1
SLOTTED JACKFITS SIMPSON260 METERS
PART NUMBER AND OTHER PLUG STYLES.
250 VOLT ½ AMP SUPPLIEDWITH LEAD
782-16 782-6 782-20 782-21 782-22
782-15782-3 782-17782-11
FUSED SERIESSAFETY LEAD
FUSE TO PLUGLEAD LENGTH 5”
The TIP on this lead is made of .080" Dia. X 1/2" long brass tip threaded 8-32 for attachments. (Nickel plated). . .The PROBE is 4" molded flame retardant ABS plastic with 3/4" safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 4 feet, Sold as Sets 1 Red and 1 Black lead.
782
STANDARD PLUG
782-5
STANDARD PLUG
782-7
STANDARD JACK
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
782-1
.080” PIN PLUG
.080” PIN PLUG
782-2
RECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
833 MINI CLIP LEAD KIT 833-1 ALLIGATOR CLIP LEAD KIT
Oldaker "TEST WITH THE BEST"
PACKAGED INREUSABLE POUCH
PAK - 5TEST LEAD KIT
BNC MODULARSAFETY TEST LEAD KIT
PACKAGED INREUSABLE POUCH
497-3 HOOKS
520 LUGS#10
623 EXTENSION TIPS
458-1 CLIPS
458-1 CLIPS
598CABLE LEAD
539 PLUGSUSED IN PAK-5
623 EXTENSION TIPS
539B PLUGSUSED IN PAK-5B
537 LEAD
538 PROBES
497-3 HOOKS
520 LUGS#10
539 PLUGSUSED IN BNC
539B PLUGSUSED IN BNC-B
538 PROBES
This lead features the ability to directly thread all accessories to both ends of the lead and eliminates accidental disconnection. All attachments recess into molded connectors to help reduce the possibility of shock. This lead consists of two 4' leads with threaded connectors on both ends, includes 1 Red and 1 Black of all accessories shown above and is packaged in a reusable plastic pouch. The wire used on this lead is a heavy duty 18 ga. 65 x 36 tinned copper stranding .145" O.D. Rubber insulation. NOTE: To order PAK-5 Kit with recessed plugs use part number PAK-5B.
This lead features the ability to directly thread all accessories to the end of the lead and eliminates accidental disconnection. All attachments recess into molded connectors to help reduce the possibility of shock. The lead comes as you see it above with 1 red and 1 black of all the accessories shown above and is enclosed in a reusable plastic pouch. The BNC lead (598) uses 3' of RG/58 CU shielded cable with 19 x .0071 tinned copper stranding center conductor, .195" O.D. PVC insulation. Rated 50 ohms, 1900 volts, color black, the connector wire is 7” of 18 ga. 65 x 36 tinned copper stranding .145" O.D. Rubber insulation. NOTE: to order BNC Kit with recessed plugs (539B) order BNC-B Kit.
PAGE 7
1 EACH OF 5 DIFFERENTCOLORS, RED, WHITE,
YELLOW, GREEN & BLACK(5 LEADS)
2 EACH OF 5 DIFFERENTCOLORS, RED, WHITE,
YELLOW, GREEN & BLACK(10 LEADS)
This is a good quality lead for the money and very useful for most handymen, this lead includes 1 each of 5 different colored, 24 ga. Wire, 1 foot long. Has clips and boots on both ends.
This is a good quality lead for the money and very useful for most handymen, this lead includes 2 each of 5 different colored, 24 ga. Wire, 2 foot long. Has mini clips and boots on both ends.
PART NUMBER AND OTHER PLUG STYLES. RATED 1,000 VOLTS 10 AMPSMODULAR SERIESSAFETY TEST LEAD KIT
REUSABLEPOUCH
This lead has a standard banana plug recessed into the probe handle to allow all of the accessories shown above to plug directly into the probe handle.The PROBE is 4" molded flame retardant ABS plastic with 3/4" safety ring. . The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 4 feet, sold as Sets 1 Red and 1 Black lead, includes 2 each of the accessories shown above and is packaged in a reusable plastic pouch.
660-2 HOOK 491A PLUG458-3 CLIP577-5 TIP660-3 NEEDLE TIP 660-1 LUG
<< PRESS-ON ACCESSORIES
660-20
660-8
STANDARD PLUG
660-10
STANDARD JACK
660-7STACKABLE STANDARDPLUG660-14
RETRACTABLE STANDARDPLUG
660-6.080” PIN PLUG
660-12
.080” PIN PLUG
660-22
RECESSEDSTANDARDSHORT PLUG
660-5
STANDARD JACK
660-9
RECESSEDSTANDARDPLUG .312”
660-21
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
660
RECESSED STANDARDPLUG
660-11
SLOTTED JACKFITS SIMPSON260 METERS
660-4STANDARD PLUG
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
These micro adapter kits allow accessories that were once reserved for scopes and scope probes to be used with standard test meters and is a new method of connecting IC's, test points, wire wrap pins, terminals and other miniature components to standard leads. The lead (4262) for 793 kit, presses onto any test lead with a .080" dia. Probe tip, and allows the user to attach any of the micro hooks or clips to the end of any standard lead set. The lead (4262-1) for 793-1 kit, allows the user to attach micro accessories to either end. The set includes 1 red, 1 black 4262 lead adapter, 1 red 4379 clip, 1 red 4359 pico hook, 1 black 4258 micro hook, 1 black 4256 pincer hook.
BNC / DUAL PLUG MICRO ADAPTER KIT
Oldaker "TEST WITH THE BEST"
598 KIT USES RG/58 CABLE490 KIT USES RG/174 CABLE
506 KIT USES RG/58 CABLE877 KIT USES RG/174 CABLE
PAGE 8
These adapter kits allow micro accessories to be used with BNC or Dual Plug Cables both RG/58 and RG/174. A new method of connecting IC's, test points, wire wrap pins, terminals and other miniature components to BNC RG/58 or RG/174 cable, using a .025” Square Socket Connection. You have your choice of either BNC or Dual plug on one end and includes 1 red 4379 clip, 1 red 4359 pico hook, 1 black 4258 micro hook, 1 black 4256 pincer hook. To order BNC RG/58 Kit use part # 598 Kit. To order BNC RG/174 Kit use part # 490 KIT, For Dual Plug RG/58 Kit use part # 506 Kit. To order Dual Plug RG/174 Kit use Part # 877 Kit.
954-1 MODULAR TEST LEAD KIT
954-2 MODULAR TEST LEAD KIT 954-3 MODULAR TEST LEAD KIT
954 MODULAR TEST LEAD KIT
PACKAGED INREUSABLE POUCH PACKAGED IN
REUSABLE POUCH
PACKAGED INREUSABLE POUCH
PACKAGED INREUSABLE POUCH
944-3 CLIP944-1 CLAMP
944-4 HOOK944-2 PIN PROBE
769-6S 6’SILICONELEAD SET
769-6S 6’SILICONELEAD SET
769-6S 6’SILICONELEAD SET
769-6S 6’SILICONELEAD SET
946 PROBE
946 PROBE 946 PROBE
946 PROBE
793-1 KIT793-1 KIT
TYPICAL APPLICATION
THESE KITS USE A .025” SQUARE SOCKET AND PIN CONNECTION
793 KITTYPICAL APPLICATION793 KIT
MICRO ADAPTER TEST LEAD KITS
43 CLIP79
K
4359 HOO
4258 HOOK
4262LEAD SET
4379 CLIP
.025”SOCKET
.025”SOCKET
24 Ga.7” LONG
24 Ga.7” LONG
CABLE LENGTH3 FEETCABLE LENGTH
3 FEET
4258 HOOK4359 HOOK
4256 HOOK
4262-1LEAD SET
4256 HO
OK
This test lead kit shown above is recommended for electrical, industrial and HVAC applications. The 954 kit comes with 944-3 Clip Probes, 946 Probe Handles and 769-6S 6’ with Silicone Insulation, and Shrouded Right Angle 4mm Plugs on each end. Kit is packaged in a reusable plastic pouch. Rated 1,000 volts / 20 amp.
This test lead kit shown above is recommended for electrical, industrial and HVAC applications. The 954-1 kit comes with 944-1 Clamp Probes, 946 Probe Handles and 769-6S 6’ with Silicone Insulation, and Shrouded Right Angle 4mm Plugs on each end. Kit is packaged in a reusable plastic pouch. Rated 1,000 volts / 20 amp.
This test lead kit shown above is recommended for electrical, industrial and HVAC applications. The 954-2 kit comes with 944-4 Hook Probes, 946 Probe Handles and 769-6S 6’ with Silicone Insulation, and Shrouded Right Angle 4mm Plugs on each end. Kit is packaged in a reusable plastic pouch. Rated 1,000 volts / 20 amp.
This test lead kit shown above is recommended for electrical, industrial and HVAC applications. The 954-3 kit comes with 944-2 Pin Probes, 946 Probe Handles and 769-6S 6’ with Silicone Insulation, and Shrouded Right Angle 4mm Plugs on each end. Kit is packaged in a reusable plastic pouch. Rated 1,000 volts / 20 amp.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
956 TEST LEAD KIT 956-1 TEST LEAD KIT
Oldaker "TEST WITH THE BEST"
PAGE 9
1520 SUPER DELUXE TELECOM LEAD KIT
1501 ECONOMY ELECTRONIC LEAD KIT
1500 SUPER ELECTRONIC LEAD KIT 1510 SUPER INDUSTRIAL AUTOMOTIVE KIT
946 PLUG TIP PROBES
769-2S 6’LEAD SET
949-1 LARGE CLIPS
949-1 CLIPS 949-2 LOWPROFILE CLIPS
769-2S 6’LEAD SET
LEFT TO RIGHT944-1 CLAMP PROBES
944-3 CLIP PROBES944-2 PIN PROBES
944-4 HOOK PROBES
667-2LEAD SET 667-3
LEAD SET
946 PLUG TIP PROBES946 PLUG TIP PROBES
958 DELUXE TEST LEAD KIT
968 TEST LEAD KIT
660-1 LUGS
660-1 LUGS
660-1 LUGS
660-1 LUG
513-27 HOOK LEADS
513-27 HOOK LEADS
513-27 HOOK LEAD
4262-2 MICRO LEADS
4256 HOOK
4359 HOOK
963 CLIPS
963 CLIPS
963 CLIPS
949-1 CLIPS949-1 CLIPS
949-1 CLIPS
949-1 CLIPS
944-3CLIP
PROBES
944-3CLIP PROBES 992-1 HEAVY DUTY HOOKS WITH NEEDLE
946 PROBES
820 TELE. CLIPS
944-1CLAMP
PROBES
521-1 ADAPTERS
963 MINI CLIPS
946 PLUG TIP PROBES
946 PLUG TIP PROBES
946 PLUG TIP PROBES
946 PLUGTIP PROBES
PLASTICPOUCH
PLASTICPOUCH
PLASTICPOUCH PLASTIC
POUCH
PLASTICPOUCH
769-2S 6’
SILICONE WIRE SILICONE WIRE
SILICONE WIRE
RUBBER WIRE RUBBER WIRE
SILICONE WIRE
SILICONE WIRESILICONE WIRE
SILICONE WIRE
SILICONE WIRE
769-2S 6’
769-2S 6’
769-2S 6’
PLASTICPOUCH
PLASTICPOUCH
PLASTICPOUCH
1521 ECONOMY TELECOM TEST LEAD KIT
660-1 LUGS
820 TELEPHONETYPE CLIP (RED)
521-1 PLUGADAPTOR (RED)
946 BANANA PLUG TIP PROBES
769-2S 6’LEAD SET
PLASTIC POUCH
949-1 CLIPS
1511 ECONOMY INDUSTRIAL / AUTOMOTIVE LEAD KIT
660-1 LUGS 946 BANANA PLUG TIP PROBES
992-1 HOOK WITH NEEDLERED ONLY
769-2S 6’LEAD SET
949-1 CLIPS
PLASTIC POUCH
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
Oldaker "TEST WITH THE BEST"
PAGE 10
814 MINI HOOK LEAD
518-26 TEST LEAD KIT2536 TEST LEAD KIT
518-27 TEST LEAD KIT
997-1 TEST LEAD KIT
876 TEST LEAD HOLDER
997 TEST LEAD KIT
518-28 TEST LEAD KIT
This mini lead uses 24 ga. Miniature test lead wire ( 45 x 40 ) tinned copper stranding with rubber insulation .066" Dia. Colors available red, black, green, white & yellow. Standard lengths are 8", 12", 24", 36". Sold by color & length. Other lengths are available upon request.
814-1 (LENGTH & COLOR)INCLUDES HOOK
ON ONE END ONLY.
PLASTICPOUCH
SCREW-ON40 AMP
CLIP SET
SCREW-ON40 AMP
BLACK CLIP
667-3LEAD SET
20 AMPBATTERYCLIP SET
945PIN PROBES
518-6RECESSED PLUGSWITH NEEDLE TIP
PROBES
STRAIGHT RECESSEDPLUGS WITH RED
NEEDLE TIP PROBEAND 40 AMP BLACK CLIP
518-2STRAIGHT RECESSEDPLUGS WITH NEEDLE
TIP PROBES
PLASTICPOUCH
PLASTICPOUCH
458-4ALLIGATORCLIP SET
458-4ALLIGATORCLIP SET
532-2LEAD SET
532-2LEAD SET
944-4RED HOOK
944-4RED HOOK
660-1LUGS
660-1LUGS
946PROBES
946PROBES
PLASTICPOUCH
PLASTICPOUCH
PLASTICPOUCH
This test lead holder measures 5.250" wide by 3" high and has 6 slots 3.250" deep for leads, the holder also has 2 screw holes for wall mounting. Color is blue.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
TELEPHONE STYLE CLIP LEADSPART NUMBER AND OTHER PLUG STYLES.
PART NUMBER AND OTHER PLUG STYLES.
HOOK SERIES LEADS
Oldaker "TEST WITH THE BEST"
PART NUMBER AND OTHER PLUG STYLES.EXTENDED HOOK STYLE LEADS
PART NUMBER AND OTHER PLUG STYLES.STACKABLE SERIES TEST LEADS
PAGE 11
527-5 527-9527-7 527-6 527-20 527-21 527-22
527-4527-1 527-3527-2 527527-10
STANDARD PLUG
STANDARD PLUG
STANDARD JACK
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUGRECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
NOTHING ON END
527-11
This lead has a telephone style clip & boot on one end with a single penetrating pin for insulation piercing and a cluster of hardened needles for a sure connection on groups of wires, also has an angled jaw for hard to reach areas. The other end has various type connections to fit any meter or connection. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. Mini leads use 20 ga. (41 x 36) tinned copper stranding .120" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot for standard leads, 3.5" for mini leads. These leads are sold as Sets 1 Red and 1 Black.
THIS HEAVY DUTY CLIP HASA SINGLE PENETRATING PINFOR INSULATION PIERCING,
ALSO HAS A CLUSTER OFNEEDLES ALONG WITH
ANGLED JAW.
This lead has a molded polyethelene stackable standard plug on one end with various other connections on the other end to fit any type of meter or connector. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot. These leads are sold as Sets 1 Red and 1 Black, single leads of different lengths can be ordered separately.
This lead has a 4.5" hook on one end which is made of molded nylon and gold plated hook with various other connections on the other end to fit any type of meter or connection. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. Mini leads use 20 ga. (41 x 36) tinned copper stranding .120" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot for standard leads, 3.5" for mini leads. These leads are sold as Sets 1 Red and 1 Black, single leads of different lengths can be ordered separately.
513-9 513-10513-11 513-12 513-20 513-21 513-22
513-14513-16 548513-13 513-18513-17
STANDARD PLUG
STANDARD PLUG
STANDARD JACK
513-25MINI PLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
513-15
.080” PIN PLUG
RECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
NOTHING ON END
513-26
HOOK
513-19
813-12
527-8
813-8
813-5 813-10813-7 813-6 813-20 813-21 813-22
813-4813-1 813-3813-2 813-15813-11
STANDARD PLUG
STANDARD PLUG
STANDARD JACK
MINI PLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
.080” PIN PLUG
.080” PIN PLUGRECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
NOTHING ON END
813-9813EXTENDED HOOK
This lead has a 2.5" hook on one end which is made of molded nylon and gold plated hook with various other connections on the other end to fit any type of meter or connection. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. Mini leads use 20 ga. (41 x 36) tinned copper stranding .120" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot for standard leads, 3.5" for mini leads. These leads are sold as Sets 1 Red and 1 Black.
812-12 812-14812-8
812-5 812-10812-7 812-6 812-20 812-21 812-22
812-4812-1 812-3812-2 812-13812-11
STANDARD PLUG
STANDARD PLUG
STANDARD JACK
812-16
MINIRECESSEDPLUG
513-1
813-14
MINIRECESSEDPLUG
MINIRECESSEDPLUG
MINI PLUGMINI .105”JACK
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
.080” PIN PLUGRECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
NOTHING ON END
812-9812
TELEPHONE CLIP
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
ALLIGATOR CLIP LEADS PART NUMBER AND OTHER PLUG STYLES.
PART NUMBER AND OTHER PLUG STYLES.
510-6
510-3 510-7
510-4 510-2 510-20 510-21 510-22
510-5550 565510-1 534510-11
511-13
609
511-8 511-9511-10 511-12 511-20 511-21 511-22
511-4511-1 511-3
511-5
511-2 543
511-6
511-11
574
604 607-1607 604-1 604-20 604-21 604-22
609-1603 606-1499-1 605603-11
MINIGATOR CLIP LEADS
Oldaker "TEST WITH THE BEST"
PART NUMBER AND OTHER PLUG STYLES.BATTERY STYLE CLIP TEST LEADS
PART NUMBER AND OTHER PLUG STYLES.
THIS LEAD IS ALSO AVAILABLEUSING 14 Ga. WIRE. RED OR BLACK
CROCODILE CLIP LEADS
PAGE 12
STANDARD PLUG
STANDARD PLUG
STANDARD PLUG
STANDARD PLUG
STANDARD PLUG
STANDARD PLUG
STANDARD JACK
STANDARD JACK
STANDARD JACK
MINIRECESSEDPLUG
476-8
MINIRECESSEDPLUG
MINI PLUG
608MINI PLUG
MINI .105”JACK
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
.080” PIN PLUG
.080” PIN PLUG
.080” PIN PLUG
.080” PIN PLUG
.080” PIN PLUG
RECESSED STANDARDPLUG
RECESSED STANDARDPLUG
RECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
RECESSEDSTANDARDSHORT PLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
STANDARD JACK
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
RECESSEDSTANDARDPLUG .380”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
SLOTTED JACKFITS SIMPSON260 METERS
SLOTTED JACKFITS SIMPSON260 METERS
This lead has an alligator clip & boot on one end which is made of nickel plated steel, ( available in copper) with PVC boot and has various other connections on the other end to fit any type of meter or connection. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot. These leads are sold as Sets 1 Red and 1 Black. Other lengths available..
This lead has a minigator clip & boot on one end which is made of nickel plated steel, ( available in copper) with PVC boot and has various other connections on the other end to fit any type of meter or connection. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. Mini leads use 20 ga. (41 x 36) tinned copper stranding .120" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot for standard leads, 3.5" for mini leads. These leads are sold as Sets 1 Red and 1 Black. Other lengths and colors (Green, White, Yellow & Blue).
NOTHING ON END
NOTHING ON END
NOTHING ON ENDALLIGATOR CLIP
MINIGATOR CLIP
510
511
764-5
511-14
510-12
This lead has a 20 AMP battery clip & boot on one end which is made of nickel plated steel, ( available in copper) with PVC boot and has various other connections on the other end to fit any type of meter or connection. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. Mini leads use 20 ga. (41 x 36) tinned copper stranding .120" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot for standard leads, 3.5" for mini leads. These leads are sold as Sets 1 Red and 1 Black.
This lead has a crocodile clip & boot on one end which is made of nickel plated steel, with PVC boot and has various other connections on the other end to fit any type of meter or connection. The wire on standard leads is 18 ga. (65 x 36) tinned copper stranding .145" O.D. RUBBER insulation. Mini leads use 20 ga. (41 x 36) tinned copper stranding .120" O.D. RUBBER insulation. All standard leads are available in SILICONE wire (440 x .002) copper stranding .145" O.D. To order silicone just add "S" to the part number. Stocked length is 4 foot for standard leads, 3.5" for mini leads. These leads are sold as Sets 1 Red and 1 Black..
602BATTERY CLIP
571
570 570-3570-2 570-1 570-20 570-21 570-22
571-1572 572-3572-1 610572-11
STANDARD PLUG
STANDARD PLUG
STANDARD JACK
764-3MINI PLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
.080” PIN PLUGRECESSED STANDARDPLUG
RECESSEDSTANDARDSHORT PLUG
STANDARD JACK
RECESSEDSTANDARDPLUG .312”
RECESSEDSTANDARDPLUG .360”
RECESSEDSTANDARDPLUG .380”
SLOTTED JACKFITS SIMPSON260 METERS
NOTHING ON END
764-6764CROCODILE CLIP
592#10 LUG
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
.100"
.185"
Oldaker "TEST WITH THE BEST"
PAGE 13
2.250" HOOK
6" OF 18 GA. RUBBERINSULATED TEST
LEAD WIRE
STANDARD BANANA JACKPLUGS INTO ANY LEAD
WITH STANDARD BANANAPLUG OF ANY TYPE.
2602 EXTENDED PROBE TEST LEAD SERIES
COIL CORD JUMPER LEADS
992-1 AUTOMOTIVE TYPE HOOK ADAPTER LEAD 982-1 GRIPPER ADAPTER LEAD
513-27 HOOK ADAPTER LEAD 2567 TEST LEAD EXTENSION
5.5" HOOK WITHINSULATION
PIERCING NEEDLE.
STANDARD BANANA JACKPLUGS INTO ANY LEAD
WITH STANDARD BANANAPLUG OF ANY TYPE.
This lead is very useful where hard to make connections are required. The narrow size allows close side by side connection for high density IC's. The hook has 2 blades that are connected directly to the wire and are shaped to make a secure connection. The other end has a standard banana jack which fits any standard banana plug, recessed or standard. The wire is 6" of 20 ga. PVC wire .100" O.D.MATERIAL = Molded nylon with stainless steel blades.SOLD = as 1 lead. Colors available are Red or Black.
This hook lead permits direct hook-up either vertically or horizontally over square wire wrap pins. The other end has a standard banana jack which fits any standard banana plug, recessed or standard. The wire used is 6" of 18 ga. RUBBER wire .140" O.D.MATERIAL = Molded nylon with gold plated beryllium copper hook.SOLD as 1 each. Colors available, Red or Black.
2.160" GRIPPERHOOK
6" OF 20 GA. PVCINSULATED TEST
LEAD WIRESTANDARD JACK
PLUGS INTO ANY LEADWITH STANDARD
PLUG OF ANY TYPE.
776-23
776-24
776-25
776-26
776-27
776-28
R/A SHROUDED PLUG TO BANANA JACK
MOLDED “Y”18 GA. RUBBER WIRE
6” LONG
2 CONDUCTOR COIL CORD1 FOOT RETRACTED, 5 FOOT EXTENDED
STRAIGHT PLUG TO R/A SHROUDED PLUG
R/A .380” SHROUDED PLUG TOSTRAIGHT SHROUDED PLUG
STRAIGHT PLUG TO R/A PLUG
R/A SHROUDED PLUG TO R/A PLUG
R/A PLUG TO ALLIGATOR CLIP
This lead is very useful where a heavy duty hook is needed. This lead accessory has an insulation piercing tip in the hook base. The other end has a standard banana jack which fits any standard banana plug, recessed or standard. The wire used is 6" of heavy duty 18 ga. 65 x 36 tinned copper stranding .140" O.D.MATERIAL = Molded nylon with nickel silver contact. SOLD = as 1 lead. Colors available are Red or Black.
This lead adapter allows the user to add 4' to any test lead that has a recessed standard banana plug.The WIRE is 4' of 18ga. (65x36) tinned copper stranding, RUBBER insulation .145" Dia. Wire is rated 20KV breakdown, 5KV working.SOLD as 1 Set. Red and Black.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
PART NUMBER AND OTHER PLUG STYLES.
15” PROBES
2602-5STANDARD PLUG
2602STANDARD PLUG
2602-8
STANDARD JACK
2602-2RECESSED STANDARDPLUG
2602-22
RECESSEDSTANDARDSHORT PLUG
2602-1STANDARD JACK
2602-6
RECESSEDSTANDARDPLUG .312”
2602-7
SLOTTED JACKFITS SIMPSON260 METERS
The TIP on this lead is made of .080" Dia. X 5/8" long stainless steel with a polished point. (Nickel plated).The PROBE is LONG For hard to reach areas. The WIRE is 18 ga. (65x36) tinned copper stranding, rubber insulation .145" Dia. 20KV breakdown 5KV working.Standard length is 5 feet, Sold as Sets 1 Red and 1 Black.
15"
532
667
547
768
2576 857
2577 858
2578 859
2579 860
2522
-3
-2
-1
-9
-19
JUMPER LEADS
THESE LEADS ARE ALSO AVAILABLE WITH SILICONE WIRE,
JUST ADD " S " TO THE PART NUMBER.
These jumper leads are available in 4 different styles of wire. Style 1 is 20 ga. (41 x 36 ) tinned copper stranding .120" Dia. Rubber insulation. Style 2 is 18 ga. ( 65 x 36 ) tinned copper stranding .145" Dia. Rubber insulation, another option is 14 ga. ( 79 x 45 ) tinned copper stranding .145” O.D. Style 3 is18 ga. ( 440 x .002 ) copper stranding .145" SILICONE insulation. Standard length 4'. Other lengths available upon request. Style 4 is coil cord, 20 ga. ( 65 x 36 ) tinned copper stranding .165" Dia. Neoprene insulation, 1' retracted, 5' extended, coil size .750". Available in Black and Red coils only.
UNLESS SPECIFIED THESE LEADS ARE SOLD AS SINGLE LEADS 4 FEET LONG, WITH STANDARD COLORS RED OR BLACK. PART NUMBERS 532, 667, 547 & 768 ALSO AVAILABLE IN GREEN, BLUE, YELLOW & WHITE.
*THESE LEADS USE 20 GA. RUBBER INSULATED WIRE
42" LONG. OTHER LENGTHS AVAILABLE UPON REQUEST, NOT AVAILABLE WITH COIL
CORD. . .
STANDARDPLUG
FIRST END
LEAD WIREPART #
18 Ga.FIRST END
LEAD WIREPART #
14 Ga.FIRST END
LEAD WIREPART #
COIL CORDSECOND END
PART #
RECESSEDPLUG
RECESSEDPLUG
.080" PIN PLUG3/4" LONG
18 GA. HEAVY DUTYRUBBER WIRE
18 GA. HEAVY DUTYRUBBER WIRE
LEAD SHOWN532-2
LEAD SHOWN2522-19
Oldaker "TEST WITH THE BEST"
PAGE 14
549
769
850
851
852
770
771
772
838
853
854
855
2581 861
2582 862
2583 863
2584 864
2585 865
2586 866
2587 867
2588 868
N/A N/A
2589 N/A
2580 N/A
N/A N/A
N/A N/A
-5
-6
-12
-13
-14
-8
-7
-10
-11
-15
-16
-17
***
RETRACTABLE STANDARD PLUG
MINI RECESSED BANANA PLUG
MINI BANANA PLUG
MINI JACK .105" DIA.
STANDARD PLUG
RECESSED STACKABLESTANDARD PLUG
RECESSEDSTANDARD PLUG
.312"
RECESSEDSTANDARD PLUG
.380"
RECESSEDSTANDARD PLUG
.360"
RECESSEDSTANDARD SHORT
PLUG
STANDARD JACK
SLOTTED JACK FITSSIMPSON 260 METERS
.080" PIN PLUG
-0NOTHING ON END
2594 -202595 N/ASTACKABLE
STANDARD PLUG
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
994 ADAPTOR LEAD
Oldaker "TEST WITH THE BEST"TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
PAGE 15
961-2 TWEEZER LEAD961-1 TWEEZER LEAD
STANDARDBANANAPLUGS
18 Ga. WIRELENGTH 5”
BNCMALE
The tweezers lead is an easy way to test surface mount devices (SMD) and allows the user one hand testing. Tips are gold plated, durable and assure positive electrical connection. Maximum voltage rating is 250 VRMS @ 3 Amps. The cable is RG/174U. Lead length 4 feet.
The tweezers lead is an easy way to test surface mount devices (SMD) and allows the user one hand testing. Tips are gold plated, durable and assure positive electrical connection. Maximum voltage rating is 250 VRMS @ 3 Amps. The cable is RG/174U. Lead length 4 feet.
765 BNC FEMALE BREAKOUT LEAD
NOTHING ON END NOTHING ON END
ALLIGATOR CLIP ALLIGATOR CLIPMINIGATOR CLIP MINIGATOR CLIPSTACKABLE PLUG STACKABLE PLUG
MINI HOOKMINI HOOK
The wire on these breakout leads is 20 ga. (41 x 36) tinned copper stranding with PVC insulation. The BNC Male connector has gold plated center contacts with a black polyethelene housing. Red wire connected to center conductor. To order add the dash number of the type of connection you want on the other end.
The wire on these breakout leads is 20 ga. (41 x 36) tinned copper stranding with PVC insulation. The BNC Female connector has gold plated center contacts with a black polyethelene housing. Red wire connected to center conductor. To order add the dash number of the type of connection you want on the other end.
-4HOOK
-5
-1 -2
-0
-3 -4HOOK
-5
-1 -2
-0
-3
775 BNC MALE BREAKOUT LEAD
4379 MINIGATOR CLIPWITH .025” PIN CONNECTOR
947 MINIATURE GRIPPER 948 SPRING LOADED PIN PROBE
2.125"
This bendable, clamp style, rotating gripper can also be used with leads 4262 and 4262-1. It is well suited for use with surface mount devices, and has extremely thin wires, can bend 35 degrees and still remain fully operable. It has two .025" square pins to plug into leads and is rated 42V. SOLD as 1 each. Red or Black.
BENDS35
o
This .030" dia. Needle point pin probe is made of stainless steel for durability and is spring loaded for reliability and accuracy. It has a .025" square pin to fit leads 4262 and 4262-1. Rated 50V. SOLD as 1 each. Red or Black.
SPRING LOADED
This adaptor lead set is replacement for the B&K Precision # FP-6. Has standard banana plugs on one end and 2.5" hooks on other. WIRE is 20 ga. (41 x 36) tinned copper stranding with PVC insulation... Standard length is 4 feet, SOLD as Sets 1 Red, 1 Black and 1 Green
1.625"
This minigator clip has a .025" square pin for direct connection to square socket on wire (Oldaker part # 4262 & 4262-1).MATERIAL = Nickel plated steel clip with molded PVC boot. SOLD = as 1 each. Red Only.
506 SERIES BREAKOUT LEAD
3 FEET RG/58, 50 OHM CABLEOTHER LENGTH AVAILABLE
UPON REQUEST.
3/4" DUAL STACKABLEBANANA PLUG.
506-2ALLIGATOR CLIP
ALLIGATOR CLIP
ALLIGATOR CLIP
506-7 506-11506-4506-14 506-8 506-3
506-5 506-10506-9
MINIGATOR CLIP
STANDARD HOOK
STANDARD HOOK
STANDARD HOOK
MINI HOOK
MINI HOOK
MINI HOOK
EXTENDED HOOK
EXTENDED HOOK
EXTENDED HOOK
MINIGATOR CLIP
MINIGATOR CLIP
506-6
NOTHING ONONE END.
NOTHING ONONE END.
NOTHING ONONE END.
7", 18 GA. HEAVY DUTYRUBBER INSULATED WIRE
OTHER STYLESLISTED BELOW
598 SERIES BREAKOUT LEAD
3 FEET RG/58, 50 OHM CABLEOTHER LENGTH AVAILABLE
UPON REQUEST. GOLDCENTER
PIN
MOLDED STRAIN RELIEFAVAILABLE IN OTHER COLORS
598-2
598-6 598-10598-4
598-12 598-7 598-3
598-1 598-8598-9598-5
7", 18 GA. HEAVY DUTYRUBBER INSULATED WIRE
OTHER STYLESLISTED BELOW
BNC MALE
766 SERIES BREAKOUT LEAD
3 FEET RG/58, 50 OHM CABLEOTHER LENGTHS AVAILABLE
UPON REQUEST. GOLDCENTER
PIN
MOLDED STRAIN RELIEFAVAILABLE IN OTHER COLORS
CABLE DESCRIPTION
The cable used on theabove leads is RG/58,
center conductor is (19 x 0071) tinned copperstranding .195" O.D. PVC
insulation Cap=29.5 PF/FT, color black.
BNC FEMALE
766-1
766-6 766-10766-3766-11 766-7 766-2
766-4 766-8766-9766-5
7", 18 GA. HEAVY DUTYRUBBER INSULATED WIRE
OTHER STYLESLISTED BELOW
490 SERIES BREAKOUT LEAD
3 FEET RG/174, 50 OHM CABLEOTHER LENGTHS AVAILABLE
UPON REQUEST.
BNC MALE
KELVIN CLIP
490-13
KELVIN CLIP
598-13
ALLIGATOR CLIP
490-2
MINI HOOK
490-4
STANDARD HOOK
490-1
MINIGATOR CLIP
490
NOTHING ONONE END.
490-3
7", 24 GA. RUBBERINSULATED WIRE
OTHER STYLES LISTED BELOW
AVAILABLE WITH BOOTTHAT COMPLETELY COVERSBNC, AVAILABLE IN COLORS
4901 SERIES
AVAILABLE WITH BOOTTHAT COMPLETELY COVERSBNC, AVAILABLE IN COLORS
5981 SERIES
CABLE DESCRIPTIONThe cable used on thislead is RG/174, centerconductor is (7 x 34)
tinned copper stranding.125" O.D. PVC insulation
Cap=30.0 PF/FT, color black.
Oldaker "TEST WITH THE BEST"
PAGE 16
STANDARD PLUG
STANDARD PLUG
STANDARD PLUG
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
STACKABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
RETRACTABLE STANDARDPLUG
.080” PIN PLUG
.080” PIN PLUG
490-12
.080” PIN PLUG
.080” PIN PLUG
RECESSED STANDARDPLUG
RECESSED STANDARDPLUG
RECESSED STANDARDPLUG
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
BNC / DUAL PLUG LEADS
3/4" DUAL STACKABLEBANANA PLUG.
506-1 = RG/58 506 = ZIP CORD 506-13 = RG/174
3/4" DUAL STACKABLEBANANA PLUG.
GOLDPLATED
PIN
559 = RG/58 599-1 = RG/174
3/4" DUAL STACKABLEBANANA PLUG.
GOLDPLATEDSOCKET
766 = RG/58
GOLDPLATED
PIN
541-2 = RG/58 541-3 = RG/59 541-4 = RG/174
OTHER COLOR STRAINRELIEFS AVAILABLE
BLACK, RED, GREEN, YELLOW, BLUE, WHITE
GOLDPLATEDSOCKET
621-1 = RG/58 621-2 = RG/59
OTHER COLOR STRAINRELIEFS AVAILABLE
BLACK, RED, GREEN, YELLOW, BLUE, WHITE
GOLDPLATEDSOCKET
622-1 = RG/58 622-2 = RG/59
OTHER COLOR STRAINRELIEFS AVAILABLE
BLACK, RED, GREEN, YELLOW, BLUE, WHITE
GOLDPLATED
PIN
BNCMALE
BNCMALE
541 = RG/58
OTHER COLOR BOOTSAVAILABLE, BLACK, RED,
GREEN, YELLOW, BLUE, WHITE
STANDARD LENGTH ON THESELEADS IS 3' , OTHER LENGTHS
AVAILABLE UPON REQUEST
CABLE DESCRIPTION
RG/58 cable has a center conductor of (19 x 007) tinned copper stranding .195" O.D. Insulation, dielectric is 116P nom, Cap 29.5 PF/Ft. Maximum operating voltage 1900 - 50 ohms, temp. Rating -55c to +90c. Color Black.
RG/174 cable has a center conductor of (7 x 34) tinned copper stranding .105" O.D. PVC Insulation, dielectric is 116P nom, Cap 30.0 PF/Ft. Maximum operating voltage 1500 - 50 ohms. Temp rating -100c to +300c. Color Black.
RG/59 cable has a center conductor of 22 ga. copper stranding .242" O.D. Insulation, dielectric is 146P nom, Cap 21 PF/Ft. Maximum operating voltage 2300 - 75 ohms, temp. Rating -40c to +80c. Color Black.
Oldaker "TEST WITH THE BEST"
PAGE 17
BNC MALE & BNC FEMALE LEADSAVAILABLE WITH DIFFERENT COLORSTRAIN RELIEFS. ORANGE, GREEN,YELLOW, BLUE, BROWN, GREY,PURPLE, BLACK, RED.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
The 949-2 is an insulated clip that attaches to standard 4mm shrouded plugs
and is low profile, the center of the jaw clamps pins up to 3/8" dia. while the teeth at the front of the jaw are designed to accommodate extremely fine wires. . . Sold as 1 each, RED or BLACK.
Oldaker "TEST WITH THE BEST"
PAGE 18
944 SERIES PROBES
945 PROBES
946 PROBES
949-2 LOW PROFILE INSULATED CLIP
963 MINI INSULATED CLIP
949-1 LARGE JAWED INSULATED CLIP
944-4
944-3
944-2
944-1
The Oldaker 944 series test probes are designed to provide utmost user safety. The 1000V products are based on the Rigid Sleeve principle: Each probe has a socket that accommodates a standard banana plug either standard, shrouded or retractable. The sleeve that surrounds the sides of the 4mm socket is insulated to keep fingers from the test area to insure a shock proof connection to 1000V. Choose from a variety of grip, pierce, clamp and hook types to find the right probe for your test and measurement applications.
The 944-1 features 2 rotating, clamp-style tongs for securely grabbing pins and wires with diameters of up to 5/32". And, thanks to the special shrink - tubing on the flexible shaft, this and all 944 probes are resistant to solder iron heat and high temperatures. Sold as RED or BLACK.
The 944-2 features a clamp-style probe with spring-loaded, stainless-steel pin that allows the user to pierce wires without removing the insulation or causing any damage to the wire. This part pierces wires up to .138" O.D. Sold as RED or BLACK
The 944-3 features a special wide-opening jaw which opens to 7/8" to accommodate a large range of test connectors in R & D labs, workstations and service departments. When the plunger is pressed the jaws simultaneously open and extend from the probe body, then close to make a tight, reliable connection. Sold as RED or BLACK
The 944-4 is the perfect tool for electricians and repair technicians working in hard-to-reach spaces. Its spring-loaded hook extends to a full 7/32" before retracting for a secure grip around the test point.. Sold as RED or BLACK
FLE
LEXAB
The 945 provides precise contact with the area being tested. Its tapered, durable steel tip (9/32" long) is perfect for penetrating insulated and backing layers on PC boards. An anti-shorting clear cap (Oldaker P/N 945-1) can be purchased separately for fine pitch testing... Sold as 1 each, RED or BLACK.
The 946 combines testing and measurement functions in one handy tool.
Its rugged, dual-function test tip is equally suitable for penetrating insulating and backing layers of printed circuit boards or for inserting directly into 4mm dia. sockets... Sold as 1 each, RED or BLACK.
945-1 TIP PROTECTOR
The 949-1 is an insulated clip that attaches to standard 4mm shrouded plugs
and has an expanded clamping range of 1", making it especially useful in a wide range of heavy duty electrical, automotive, marine, aviation and industrial test measurement applications ... Sold as 1 each, RED or BLACK.
The 963 clip is an insulated minigator with standard banana jack to fit shrouded or exposed plugs. . . SOLD as 1 each, RED or BLACK.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
This threaded adapter converts any standard banana plug to a threaded connection and allows the user to thread on any of the Oldaker adapters directly to the plug end and changes meter lead to a jumper lead.MATERIAL = nickel plated brass with molded in polyethelene insulator.SOLD as Sets 1 Red and 1 Black.
This 8-32 threaded Hook-It attaches directly onto any test probe tip with matching threads and allows the user to attach lead to any small connector.MATERIAL = .028" silver coated beryllium copper wire with nickel plated brass insert and molded nylon housing. SOLD as Sets 1 Red and 1 Black.
2.2"
50
THREADED8-32
.027".175"
.150"
497-3 HOOK-IT
623 & 623-3 THREADED EXTENSION TIPS521-1 PLUG ADAPTER
Oldaker "TEST WITH THE BEST"
PAGE 19
These extended tips thread onto any standard probe tip with 8-32 threads, and allows the user to reach difficult areas, it also has a stainless steel tip with a polished point for insulation piercing or penetrating coated connections. The tip is fully insulated to the point to prevent shorting.MATERIAL = .045" Dia stainless steel needle tip. 623 is 5” long, 623-3 is 3.25” long. The base is nickel plated brass with 8-32 threads and is molded in polyproplene. SOLD as Sets 1 Red and 1 Black.
with cut resistant clear shrink tubing,
5"
623
3.25”
623-3
521 PLUG ADAPTER
This threaded adapter converts any standard banana plug, recessed or exposed, to a threaded connection and allows the user to thread on any of the Oldaker adapters directly to the plug end and changes meter lead to a jumper lead.MATERIAL = nickel plated brass with molded in polyethelene insulator.SOLD as Sets, 1 Red and 1 Black.
520 LUG ADAPTER
TYPICAL APPLICATION
This threaded adapter converts any 8-32 threaded probe tip to a #10 lug.MATERIAL = #10 lug with nickel plated brass insert threaded 8-32 and molded ABS insulator.SOLD as Sets 1 Red and 1 Black.
498 TIP PROTECTOR
MATERIAL = Polypropelene.SOLD = as Sets 2 Red and 2 Black.
BEFORE
PROTECTS USERFROM SHORTING
OUT TIP. . .
AFTER
458-4 ALLIGATOR CLIPS FIT RECESSED 4 mm PLUG
This alligator clip set fits any standard recessed 4mm plug.MATERIAL = Nickel plated steel.SOLD = Part # 458-4 is Sold as Sets, 1 Red and 1 Black.
820 THREADED TELEPHONE STYLE CLIP
This clip set threads directly onto any lead with an 8-32 threaded tip, and adds the ability to clip onto larger parts. Clip length is 2 19/32" x 15/16" high and has a PVC boot. Sold as Sets 1 Red and 1 Black, can be ordered separately.
TYPICAL APPLICATION
458-3 ALLIGATOR FITS 4 MM PLUGS
This alligator clip set fits any standard 4mm plug.MATERIAL = Nickel plated steel.SOLD = Part # 458-3 is Sold as Sets, 1 Red and 1 Black.
458-1 THREADED CLIPS
This 8-32 threaded alligator clip (149-2) attaches directly to threaded probe.MATERIAL = Nickel plated steel with 8-32 threaded end. The Boot (226) is PVC.SOLD = Part # 458-1 is Sold as Sets, 1 Red and 1 Black.
THIS ADAPTER FITSNON RECESSED PLUGS ONLY
THIS ADAPTER FITSNON RECESSED PLUGS ONLY
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
TYPICAL APPLICATION
TO METER
4' LEAD 966-1ADAPTER
USER
4' LEAD
USES 226 BOOT
This adapter threads onto any lead with an 8-32 threaded tip and allows the user to attach any of the Oldaker 944 series heavy duty lead accessories to any of the Oldaker standard lead sets (See Illustrations Above). This adapter also accepts The Oldaker insulated clip 949 series and if required Oldaker Part Numbers 945 & 946 can also be attached. Sold as Sets, 1 Red and 1 Black.
966-2 PROBE ADAPTER
966-1 TEST LEAD EXTENSION 966 ADAPTER KIT
966 PLUG TO PLUG ADAPTER
Oldaker "TEST WITH THE BEST"
PAGE 20
One end of this adapter threads onto any probe with an 8-32 threaded tip and allows the user to attach any lead with a standard banana plug, (shrouded or exposed) to the other end which will extend a standard 4' lead to 8' . (See Diagrams Above). Sold as sets, 1 Red and 1 Black.
This adapter has standard banana jacks on each end and allows the user to attach any lead with a standard banana plug, (shrouded or exposed) to the end of another standard banana plug lead which will extend a standard 4' lead to 8' . (See Diagrams Above). Sold as Sets, 1 Red and 1 Black.
STANDARD PLUG STANDARD PLUG
THREADED PROBE
966-2 ADAPTER
PLUG-IN ACCESSORY
INSERT BOTH PLUGS IN EACHEND OF THE ADAPTER.
This complete adapter kit has 1 set of all the adapters shown on this page. The kit includes 1 red and 1 black of each of the following adapters, 521-1, 966, 966-1 and 966-2. The kit comes packaged in a reusable plastic pouch.
PRESS ATTACHMENT ONTOEND OF ADAPTER PLUG.
This heavy duty 2.625” telephone type clip has a cluster of hardened needles and also a single pin for extra secure connection and a wide opening jaw (1.312"). 815 is Sold as 1 Clip. 815-1 Boot is Sold as 1 Boot, Red or Black.
815 BED OF NAILS CLIP
85- O
11 B
OT
149-2 THREADED ALLIGATOR CLIP
This 8-32 threaded alligator clip attaches directly to threaded probe.MATERIAL = Nickel plated steel with 8-32 threaded end.SOLD = Part # 149-2 is sold as 1 Clip. Part # 226 is Sold as 1 Boot, colors available are red, black, blue, green, yellow & white.
149 ALLIGATOR CLIP
USES 226 BOOT
This alligator clip can be soldered or crimped directly to wire.MATERIAL = Nickel plated steel. SOLD = Part # 149 is Sold as 1 Clip. Part # 226 is Sold as 1 Boot, colors available are red, black, blue, green, yellow & white..
149-4, 458-5 ALLIGATOR CLIP FITS PIN PLUG
USES 226 BOOT
This Mueller #60PR clip attaches directly to .080” pin plug. MATERIAL = Nickel plated steel. Part # 149-4 is Sold as 1 Clip. Part # 226 is Sold as 1 Boot, colors available are red, black, blue, green, yellow & white.. Also Available, Part # 458-5, Which is Clip & Boot assembled and Sold as Sets 1 Red & 1 Black.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
977 STUB NOSE CLIP
This Mueller #46A clip is plated steel with crimp connection and plastic handles. 977 clip is Sold as 1 clip, please specify Red or Black.
249 MINI CLIP 668 CROCODILE CLIP
Oldaker "TEST WITH THE BEST"
PAGE 21
This Mueller #85 crocodile clip has a screw for attaching wire. Clip is made of plated steel. 668 clip is sold as 1 Clip. Part # 680 is Sold as 1 Boot. Colors available are red, black, green, blue, yellow & white.
USES 277A BOOTUSES 680 BOOT
This Mueller #30BL clip is made of nickel plated steel and can be crimped or soldered. 249 clip is Sold as 1 Clip. Part # 277A is Sold as 1 Boot, please specify color, Red or Black.
170-1 20 AMP CLIP
170-1C IS COPPER CLIP
USES 684-1 BOOT
This Mueller #27 clip is plated steel with screw. 170-1 is Sold as 1 Clip. Part # 684-1 is Sold as 1 Boot, please specify Red or Black.
170-3 50 AMP CLIP
USES 684-3 BOOT
This Mueller #21A clip is plated steel with screw. 170-2 clip is Sold as 1 clip. 684-3 boot is Sold as 1 boot of one color, please specify Red or Black.
170 10 AMP CLIP
USES 684 BOOT
170C IS COPPER CLIP
This Mueller #48B clip is plated steel with screw connection. 170 is Sold as 1 Clip. Part # 684 is sold as 1 Boot, please specify Red or Black.
170-2 40 AMP CLIP
USES 684-2 BOOT
170-2C IS COPPER CLIP
This Mueller #25 clip is plated steel with screw. 170-2 is Sold as 1 Clip. Part # 684-2 is sold as 1 Boot, please specify Red or Black.
This hook is field repairable and is designed for difficult IC test connections. Lightweight (less than 1 gram) and finger-eze Hypo Action permits direct hook-up to delicate wires where weight & leverage may damage component. Available in 10 different colors, red, black, brown, orange, yellow, green, blue, violet, grey & white.MATERIAL = Gold plated beryllium copper conductor with molded nylon housing. SOLD as 1 Each, Select Color. . .
817 MINI MICRO HOOK
1.750"
This hook is field repairable and permits direct hook-up either vertically or horizontally over square wire wrap pins. and is available in 10 different colors, red, black, brown, orange, yellow, green, blue, violet, grey & white.MATERIAL = Gold plated beryllium copper conductor with molded nylon housing. SOLD as 1 Each, Select Color.
454 HOOK
2.250"
BODY
ATTACH WIRE
PLUNGER
This 5" hook is field repairable and permits direct hook-up either vertically or horizontally over square wire wrap pins.MATERIAL = Gold plated beryllium copper with molded nylon housing. SOLD as 1 Each Red Or Black.
5.000"
816 EXTENDED HOOK
BODY
ATTACH WIRE
PLUNGER
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
This pico hook has one .025" square pin which plugs into wire socket and is designed for direct connection to a single leg of a DIP or other components with a maximum diameter of .025".MATERIAL = Molded nylon with gold plated center contact.SOLD as 1 Each. Available in 10 colors, brown, black, red, orange, yellow, green, blue, violet, gray & white.
.100"
.016"
.013"
1.420"
4359 PICO HOOK WITH .025” PIN
Oldaker "TEST WITH THE BEST"
PAGE 22
1.75"
This micro hook is designed for difficult IC test connections. Has .025" square pin connector which plugs directly onto wire socket. MATERIAL = Molded nylon with gold plated center contact.SOLD as 1 Each, available in 10 colors brown, black, red, orange, yellow, green, blue, violet, gray & white.
4258 MICRO HOOK WITH .025” PIN
2.160"
This hook is designed for hard to make test connections with different shapes and sizes. The narrow size allows close side by side connection for high density IC's. The hook has 2 blades that are connected directly to the wire and are shaped to make a good connection, and is field repairable. Available in red, black, blue, green, yellow & white.Material = molded nylon with stainless steel blades. Sold = as 1 Each, Select Color.
.100"
.185"
982 DOUBLE GRIPPER
This double grip hook assures solid positive connection and with a narrow configuration (.050" wide) makes it ideal for side by side stacking. It also has dual .025" square pins for plug in connection, its spring loaded design is easy to use and assures solid positive contact.MATERIAL = Molded Nylon.SOLD as 1 Each. Available in 10 different colors, black, brown, red, orange, yellow, green, blue, violet, gray & white.
.060"
.018"DIA.
.090"
4256 DBL-GRIPPER WITH .025” PINS
2.250"
992 AUTOMOTIVE TYPE HOOK
5.5"
This heavy-duty test hook is ideal for automotive testing, solder connection. Has sharp point in hook for sure contact. Available in black, brown, blue, orange, yellow, grey and white.MATERIAL = Molde nylon with nickel silver contact. SOLD as 1 Each.
491B THREADED 4 mm PLUG
This standard banana plug fits .175" Dia. Jack and is threaded 8-32. NOTE = This is a stand alone plug, no insulator.Material = knurled nickel plated brass body with nickel silver contacts.Sold = as 1 Plug.
1.062"
.257" DIA.THREADED
8-32
RATED 15 AMP.
284-3 .080” PIN PLUG
This standard pin plug has a .080" Dia. Pin and must be soldered onto wire and pressed into insulator 457C.MATERIAL = Nickel plated brass.SOLD = as 1 Pin Plug.
1.5"
.080"
.187" DIA.
USE INSULATOR457C FORPIN PLUG.
491A STACKABLE 4 mm PLUG
This standard stackable banana plug fits .175" Dia. And has .166" Dia hole in back. NOTE = This is a stand alone plug, no insulator.Material = knurled nickel plated brass body with nickel silver contacts.Sold = as 1 Plug.
1.5"
.250" O.D.DRILLED.166" DIA.
RATED 15 AMP.
RATED 10 AMP.
491 SOLDER & PRESS 4 mm PLUG
This standard banana plug fits .175" Dia. Jack and must be soldered onto wire and pressed into insulator 457B (recessed) or 457C (standard).Material = knurled nickel plated brass body with nickel silver contacts.Sold = as 1 Plug.
1.062"
.192"
RATED 15 AMP
USE INSULATOR457B FOR RECESSED
BANANA PLUG.
USE INSULATOR457C FOR
BANANA PLUG.
.187" DIA.
.540"
450 MINI PLUG
This mini plug fits a .105" jack and must be soldered onto wire and pressed into insulator 457C.MATERIAL = Nickel plated brass body with nickel silver contacts.SOLD = as 1 Mini Plug.
USE INSULATOR457C FORMINI PLUG.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
This lug adapter fits any standard or recessed banana plug. The lug fits any size terminal from .100" to .300".Material = nickel plated brass body with nickel plated copper lug.Sold = as 1 lug.
457B insulator is for a recessed standard banana plug 491 and 457D insulator is used with 456C banana jack and 456D threaded jack.MATERIAL = ABS V0/94 flame retardant plastic.SOLD = as 1 Each. Available in red, black, green, yellow, blue and white.
826 RETRACTABLE 4 MM PLUG SAFETY RECESSED STACKABLE 4 MM PLUG
25222594
2571 2 MM SOCKET
457C INSULATOR FOR 450, 491,& 284-3 PLUGS 660-1 LUG ADAPTER FITS 4 MM PLUG
457B INSULATOR FOR 491 PLUGS.457D INSULATOR FOR 456C & 456D JACKS
908-1 SOCKET & 908-2 PLUG2 MM BANANA PLUG & INSULATOR 2570
456C 4 MM BANANA JACK & 456D THREADED JACK
Oldaker "TEST WITH THE BEST"
PAGE 23
This 2 mm safety insulated jack (2571) is for surface mount and has a .187” tab for solder connection or slide connector.MATERIAL = Nylon.SOLD = As 1 Jack, Specify Color (Red Or Black)..
This 3 piece recessed safety stackable plug is a solder type and then snaps together.. Plug 2522 is covered, 2594 is not covered.Material = Nickel plated brass body with nickel silver contacts. Plastic housing is Molded nylon.Sold = as 1 Plug. Colors available are Red, Black, Yellow, Blue & Green.
DO-IT YOURSELF,JUST SOLDER ANDSNAP TOGETHER.
The 456C banana jack accepts any standard banana plug. The 456D is an 8-32 threaded jack. Both types must be soldered to wire and pressed into 457D insulator.MATERIAL = nickel plated brass456C IS SOLD = as 1 Each of banana jack.456D IS SOLD = as 1 Each of threaded jack.
Use Insulator 457DFor Both 456C & 456D
.750"
.187" O.D.
This 2 mm banana plug (2570) must be soldered to wire and pressed into insulator.MATERIAL = nickel plated brass, nickel silver contacts. Insulator Molded Nylon.
This insulator accepts part numbers 450, 491 & 284-3 and when pressed together becomes a miniature banana plug, a standard banana plug or a standard pin plug.MATERIAL = ABS V0/94 flame retardant plastic.SOLD = as 1 Each. Available in red, black, green, yellow, blue and white.
The 908-1 jack is threaded 8-32. The 908-2 4 MM plug is threaded 8-32.MATERIAL = Nickle plated brass body with nickle silver contacts and molded Polyproplene.SOLD = as 1 each of 1 color. Select 908-1 Jack or 908-2 Plug. Colors Red Or Black.
INCLUDESINSULATOR
JACK & PLUGCAN BE THREADED
TOGETHER.
1.5"
1"
.710"
1.750"
.250" O.D.
.31 .D.2" O
.110"TO
.300".435"
This plug fits any meter that requires a banana plug, makes no difference if it takes recessed or standard. The sleeve is spring loaded and covers the contacts when the plug is removed from the meter. Total length, 2.335"MATERIAL : molded nylon with nickel,plated brass body and gold plated contacts.SOLD : as 1 Plug. Select Color, Red or Black.
.787"
.460” .030”
1
01.
10” .4
75”
1.150"
2514 SERIES HI-VOLTAGE PROBE HANDLES WITH TIPS
2514 Uses tip “B”. Nickel Plated Brass not threaded.2514-1 Uses tip “A”. Stainless Steel Needle Tip and threaded for accessories.SOLD = as 1 Probe Each. Choose Red Or Black.. Tips can be ordered separately, 106HH has a threaded needle tip, 106KK has a .080” brass tip. Sold as Each.
4.875"
TIP “A”
106HH 106KK
TIP “B”
.875".500" MATERIAL:
POLYPRO.
THREADED1/4-28
I.D. .305”WALL
THICKNESS .097”
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
This adapter has a red and black binding post with cross holes for stacking on one end and a BNC female on the other.MATERIAL = ABS. Nickel plated brass. SOLD = as 1 Each.
Radiused edges, eliminates scarring of leads. Graduated in .050" increments. Made of high impact red cycolac plastic. Size - 5 1/2" long.
MODEL 962-1 FORMS:1 WATT2 WATT
1" BODY LENGTH1.25" BODY LENGTH
MODEL 962-2 FORMS:DIODES1/4 WATT1/2 WATT MODEL 962-2
MODEL 962-1
This 2 piece crimp style fuse holder uses 1/4" dia. Fuses from 7/8" to 1 1/4" long, up to 30 Amp. MATERIAL : molded nylon, color yellow SOLD : as 1 Each
805-3 DBL-PLUG TO BNC MALE
796 IN-LINE FUSE HOLDER 984 BNC MALE984 > RG/58 984-1 > RG/59
985 BNC FEMALE985 > RG/58 985-1 > RG/59
836 NEEDLE TIP & INSULATOR COMBO
APROX.2” TO 2.5”
962 LEAD BENDER
805-2 DBL-PLUG WITH SET SCREWS 985-2 BULKHEAD BNC FEMALE CONNECTOR.
805-6 DBL-BINDING POST TO BNC FEMALE805-5 DBL-BINDING POST TO BNC MALE
805-4 DBL-PLUG TO BNC FEMALE
Oldaker "TEST WITH THE BEST"
PAGE 24
This plug adapter has double stackable banana plugs with set screws for attaching wire. Colors are Red or Black.MATERIAL = ABS with nickel plated brass. SOLD = as 1 Each, Select Red or Black.
This adapter has double stackable banana plugs with cross holes on one end and BNC male on other.MATERIAL = ABS Black. Plugs nickel plated brass. SOLD = as 1 Each.
This adapter has double stackable banana plugs with cross holes on one end and a BNC female on the other.MATERIAL = ABS Black. Plugs nickel plated brass. SOLD = as 1 Each.
This adapter has a red and black binding post with cross holes for stacking on one end and BNC male on the other.MATERIAL = ABS. Nickel plated brass. SOLD = as 1 Each.
This is a BNC Female Bulkhead type connector and has gold center conductor and nylon plastic threaded base, solder connection.SOLD = as 1 Each.
This tip and insulator combo includes one .080" stainless steel needle tip, polished point, threaded 8-32 and one 5" ABS molded insulator. Colors are Red or Black.. MATERIAL: molded ABS with nickel plated brass tip and stainless steel needle tip. Note: Tip threads into insulator.SOLD: as 1 Each, Tip and Insulator, please specify color, Red or Black.
These BNC dual crimp connectors are for RG/58 and RG/59 cable. The male BNC part # is 984, The female BNC part # is 985.MATERIAL = Non tarnish finish, Gold plated center jack. SOLD = as 1 Each.
.37
5”
.340”
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
Oldaker "TEST WITH THE BEST"
PAGE 25
OTHER ACCESSORIESAVAILABLE
HANDS FREESOLDERINGHANDS FREESOLDERING
“THE THIRD HAND” WILL FIT ANYSOLDERING IRON UP TO 7/8”
WIRE WRAP GROUND
MICRO HOOK
CHANNELMARKERS
PROBE HOLDER
PINCER HOOK
PICO HOOK
ALLIGATOR TIP
WIRE WRAP TIP
12” GROUND LEAD
4265
4258
4271
4272
4256
4257
4270
42644263
PART #3501350235033504
3504RP3505
3505RP350635103511351235133515
ATTEN.SWT 1X-10XSWT 1X-10X
FIXED 1XFIXED 10XFIXED 10XFIXED 10XFIXED 10XFIXED 10X
FIXED 100XFIXED 1XFIXED 1X
FIXED 10XSWT 1X-10X
B.W.MHz@ 30B5/100
10/20020
1001002002001001001215
3006/250
RISETIMEN.S.
70/3.535/1.417.53.53.51.41.411.03.560
23.31.16
58/1.4
LOADINGpF MO
90/16 1/1060/15 1/10
45 115 1015 1013 1013 1010 604 10
N/A N/AN/A N/AN/A N/AN/A N/A
LENGTH5 FOOT5 FOOT5 FOOT5 FOOT5 FOOT5 FOOT5 FOOT6 FOOT5 FOOT6 FOOT6 FOOT5 FOOT6 FOOT
DCMAX500 V500 V500 V500 V500 V500 V500 V600 V500 V600 V500 V500 V500 V
SCOPE PROBE SELECTION CHART
R.P.OPTION = Available with readout pin, the readout actuator option (permanently attached), is available on the 10X fixed probes only. This option provides necessary resistor circuit to change the range factor on model 465, 475, 485 & 7000 series Tektronix scopes.
HEAVY DUTY - RUGGED - RELIABLE
3 POSITION SWITCH (1X, REF, 10X)
COMPENSATION FOR ALL SCOPES
FLEXIBLE 5 FOOT CABLE.
OLDAKER SCOPE PROBES
971 “THE THIRD HAND”
This handy fixture gives the user a 3rd hand, it holds the iron in place while you assemble and solder. 2 way adjustment with replacement parts available. Fits any soldering iron up to 7/8” Dia. Made of aluminum and measures 6" x 6' x 12”. SOLD as 1 Unit Without soldering iron. Includes Instructions.
MULTI ADJUSTABLE
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312
PART #288-1
588-4
288
RG/U58C
59
174
NOMO.D..195"
.242"
.105"
CAPpF / FT
29.5
21.0
30.0
IMP.OHMS
50
75
50
COLORSBLACK
BLACK
BLACK
PUT-UPIN FEET
10-25-50-100250-500-100010-25-50-100250-500-100010-25-50-100250-500-1000
VOLTS1900
2300
1500
INSUL.TYPE
P.ETHEL.
P.ETHEL.
P.ETHEL.
SHIELDT.COPPER
COPPER
T.COPPER
TEST LEAD WIRE, 14, 18, 20 & 24 GA. RUBBER, PVC, SILICONE
F O R A C O M P L E T E U P T O D A T E C R O S S R E F E R E N C E C H E C K
O N - L I N E A T w w w . t e s t l e a d s . n e t . C L I C K O N C R O S S R E F E R E N C E .
PART #183
183A
183B
183C
184
184B
990
GA. - STRAND18 (65 X 36)
18 (65 X 36)
18 (440 X 002)
14 (7x24 X 36)
20 (41 X 36)
20 (10 X 30)
24 (45 X 40)
INSUL.THICK.045"
.045"
.045"
.033”
.040"
.032"
.019"
INSUL.TYPE
RUBBER
PVC
SILICONE
PVC
RUBBER
PVC
RUBBER
VOLTAGE5K - 20K
5K - 20K
5K - 20K
5K - 20K
1.5K - 6K
600 V
1K - 10K
COLORSRED, BLK, BLU,GRN, YEL, WHTRED & BLACK
RED & BLACK
RED & BLACK
RED & BLACK
RED, BLK, BLU,GRN, YEL, WHTRED, BLK, BLU,GRN, YEL, WHT
PUT-UPIN FEET
10-25-50-100250-500-100010-25-50-100250-500-100010-25-50-100250-500-1000
10-25-50-100250-500-100010-25-50-100250-500-100010-25-50-100250-500-1000
10-25-50-100250-500-1000
O. D..145"
.145"
.145"
.145”
.120"
.102"
.066"
Oldaker "TEST WITH THE BEST"
PAGE 26
COAXIAL CABLE, RG 58, RG 59, RG 174
COIL CORDS - 1 & 2 CONDUCTOR.
106FF NICKLE PLATED BRASS TIP 106GG NICKLE PLATED NEEDLE TIP
742 (COLOR) = 1 CONDUCTOR 20 GA. NEOPRENE INSULATION.165" O.D. 1 FOOT RETRACTED, 5 FOOT EXTENDED
3/4" DIA. COIL, 12" STRAIGHT ENDS. SOLD AS 1 COLORRED OR BLACK.
106GG TIP HAS A .080” X .625” STAINLESS STEEL NEEDLETIP WITH POLISHED POINT PRESSED INTO A BRASS BODY.TIP BODY SIZE IS KNURLED TO .198” DIA. AND IS SOLDERTYPE CONNECTION.PART IS NICKLE PLATED AND SOLD AS 1 EACH.
106FF TIP HAS A .080” X .625” BRASS TIP.BODY SIZE IS KNURLED BRASS TO .198” DIA.AND IS SOLDER TYPE CONNECTION.PART IS NICKLE PLATED AND SOLD AS 1 EACH.
780 = 2 CONDUCTOR 24 GA. PVC INSULATION.220" O.D. 1 FOOT RETRACTED, 4 FOOT EXTENDED
5/8" DIA. COIL, 12" STRAIGHT ENDS. SOLD AS 1 COLOR,BLACK.
TEL : (419) 759-3551 www.testleads.net FAX : (419) 759-3312