7/27/2019 Template- Scientific and Technical Bulletin

http://slidepdf.com/reader/full/template-scientific-and-technical-bulletin 1/2

 Sc. and Tech. Bull. of the ”Aurel Vlaicu” Univ. Arad, Mech. Eng. Vol. 1 (No. 3), 2005

THE MODEL OF A PAPER 

FOR THE SCIENTIFIC AND TECHNICAL BULLETIN OF THE

“AUREL VLAICU “ UNIVERSITY OF ARAD,

SERIES: MECHANICAL ENGINEERING

Viorel DAMIAN*; Andrei POPESCU**

*The “Aurel Vlaicu” University, Arad, Faculty of Engineering, 77 Revolutiei Bd., 2900

Arad, Romania;** The “Politehnica” University of Timisoara, Faculty of Mechanics, 1 Mihai Viteazu Bd.,

1900 Timişoara, Romania

Abstract: The abstract is written in English, just as the rest of the article, justified, Times New Roman, 10cpi. It has to point out briefly the subject of the article, the relevance of the

study, as well as the original contributions of the authors.

Keywords: maximum 5 keywords are given

1. Introduction

The page set-up is in MS-Word, format A4 (210mm x 297mm), one column, andfonts Times New Roman 10cpi for the entire paper, including titles, subtitles and

references.The title is centered, bolded, with capitals. All the distances (between the title and

the abstract and so on are 10 cpi). The subtitles are also bolded, written in small characters.The introduction must contain, clearly stated, the significance of the domain and

the original contributions of the authors (contained in the paper) with regard to the state-of-the-art.

 2. The text

The text should be justified. The margins are: top 5.7 cm, bottom 5.5 cm, left,right 4 cm. The line spacing: single. The paper should be 6 to 10 pages long (un uneven

number of pages is permitted).

3. Figures and tables

Figures are to be edited in AUTOCAD (by example) and imported in Word, with

a good resolution; they have to be properly inserted in the text. The titles of the figures are

written below, centered, with Times New Roman, 9 cpi, italic (Fig.1).The tables are numbered (Table 1) and they should be given a title above, left

aligned. All the figures and the tables must be mentioned in the text and they should be

 placed as close as possible to the first place they are mentioned.

4. Equations

The equations, such as this one:

 __________________________________________________________________  67

7/27/2019 Template- Scientific and Technical Bulletin

http://slidepdf.com/reader/full/template-scientific-and-technical-bulletin 2/2

 Sc. and Tech. Bull. of the ”Aurel Vlaicu” Univ. Arad, Mech. Eng. Vol. 1 (No. 3), 2005

   

   −⋅+−=

nnn

ε θ θ ε ε δ 

sinarcsinsinarcsin),( (2)

are right-aligned, edited and numbered as in this example.

 Fig.1. The functions of the deviation angles )( R R

λ δ δ  = and  )( B B

λ δ δ  =and the resulting dispersion δ  ∆

The diameter of the holes with regard to the curvature Table 1

R [mm] < 152 152…300 > 300

d[mm] > 1.8 > 2 R  ⁄ 225

5. Conclusions

The paper must contain a final paragraph of Conclusions, followed by theAcknowledgments (if necessary) and the References, as in this example.

The paper is sent to the Editor only by e-mail, as an MS-Word attachment, at the

following address: dumavirgil @yahoo.co.uk .

6. Acknowledgements

The author should mention the sources of funding for the research, as well as the

other acknowledgements for the various support received.

7. References

1. M. Bass, Handbook of Optics, vol. I, II, McGraw-Hill, N.Y. 1995;

2. A. Cristea, C. Tudor, “The Mathematical and the Experimental Analysis of the Scanning

Devices”, Annals of the “Aurel Vlaicu” Univ. of Arad, 1997, pp. 87÷96 (in Romanian);

3. G.C. Moisil, E. Curatu, Optics. Theory and Applications,  Tehnica, Bucharest 1986 (in

Romanian);

4. Popescu A., Anton, D.: ”Laser Scanning Devices”, 9 Kongreβmesse fur Industrielle

Meβtechnik, Mess Comp 9, Wiesbaden 1995, pp. 54-61.

 __________________________________________________________________ 68