Table of Contents Landscape Pull Type Rakes › ... › 302-223m.pdf · 07/14/08 LRP05 & LRP15...

Cover photo may show optionalequipment not supplied withstandard unit.

© Copyright 2008 Printed

Read the Operator’s manual entirely.When you see this symbol, thesubsequent instructions andwarnings are serious - follow withoutexception. Your life and the lives ofothers depend on it!

!

Table of Contents

302-223M

Landscape Pull Type Rakes

Operator’s Manual

07/14/08

20997LRP05 Series

20997

LRP15 Series

LRP05 & LRP15 Series

Table of Contents

LRP05 & LRP15 Series Landscape Pull Type Rakes 302-223M 07/14/08

Land Pride

Table of Contents

© Copyright 2008 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation ofthis manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the informationcontained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of itspublication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Important Safety Information . . . . . . . . . . .1Signal Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . .5Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 5

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 5Serial Number Plate . . . . . . . . . . . . . . . . . . . . . 5

Section 1: Assembly and Set-up . . . . . . . .6Series LRP05 Landscape Rakes . . . . . . . . . . . . . . 6Series LRP15 Landscape Rakes . . . . . . . . . . . . . . 7

LRP05 Grader Blade (Optional) . . . . . . . . . . . . 8LRP15 Grader Blade (Optional) . . . . . . . . . . . . 9

Section 2: Operating Instructions . . . . . .10Operating Instructions . . . . . . . . . . . . . . . . . . . . . 10

Section 3: Adjustments . . . . . . . . . . . . . .11LRP05 & LRP15 Rake Angle . . . . . . . . . . . . . . . 11LRP05 & LRP15 Lever Height Control . . . . . . . . . 11LRP15 Turnbuckle Height Control . . . . . . . . . . . . 11LRP05 Flip Down Grader Blade (Optional) . . . . . 11LRP15 Flip Down Grader Blade (Optional) . . . . . 12

Section 4: Maintenance and Lubrication 13Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

LRP05 & LRP15 Lever Arm Pivot Point . . . . . .13LRP15 Rear Axle Weldment . . . . . . . . . . . . . . 13Rake Teeth . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Rear Wheel Bearings . . . . . . . . . . . . . . . . . . . 13

Section 5: Options . . . . . . . . . . . . . . . . . .14LRP05 & LRP15 Flip Down Grader Blade . . . . . .14

Section 6: Specifications & Capacities . .15Section 7: Features and Benefits . . . . . .16Section 8: Appendix . . . . . . . . . . . . . . . . .17

Torque Values Chart . . . . . . . . . . . . . . . . . . . . . . 17Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Important Safety InformationLand Pride Table of Contents

▲

Important Safety InformationThese are common practices that may or may not be applicable to the products described in
this manual.
!Be Aware ofSignal WordsA Signal word designates a degree orlevel of hazard seriousness. Thesignal words are:

Indicates an imminently hazardoussituation which, if not avoided, willresult in death or serious injury. Thissignal word is limited to the mostextreme situations, typically formachine components that, forfunctional purposes, cannot beguarded.

! DANGER

Indicates a potentially hazardoussituation which, if not avoided, couldresult in death or serious injury, andincludes hazards that are exposedwhen guards are removed. It may alsobe used to alert against unsafepractices.

Indicates a potentially hazardoussituation which, if not avoided, mayresult in minor or moderate injury. Itmay also be used to alert againstunsafe practices.

! WARNING

! CAUTION

For Your Protection▲ Thoroughly read and understand

the “Safety Label” section, read all

Shutdown and Storage▲ Lower machine to ground, put

tractor in park, turn off engine, and

Safety at All TimesThoroughly read and understandthe instructions given in thismanual before operation. Refer tothe “Safety Label” section, readall instructions noted on them.Do not allow anyone to operatethis equipment who has not fullyread and comprehended thismanual and who has not beenproperly trained in the safeoperation of the equipment.

▲ Operator should be familiar withall functions of the unit.

▲ Operate implement from thedriver’s seat only.

▲ Do not leave tractor or implementunattended with engine running.

▲ Dismounting from a movingtractor could cause serious injuryor death.

▲ Do not stand between the tractorand implement during hitching.

▲ Keep hands, feet, and clothingaway from power-driven parts.

▲ Wear snug fitting clothing to avoidentanglement with moving parts.

▲ Watch out for wires, trees, etc.,when raising implement. Makesure all persons are clear ofworking area.

▲ Turning tractor too tight maycause implement to ride up onwheels. This could result in injuryor equipment damage.

07/14/08 LRP05 & LR

instructions noted on

Look For The Safety Alert SymbolThe SAFETY ALERT SYMBOL indicates there is apotential hazard to personal safety involved and extrasafety precaution must be taken. When you see thissymbol, be alert and carefully read the message thatfollows it. In addition to design and configuration ofequipment, hazard control and accident preventionare dependent upon the awareness, concern,prudence and proper training of personnel involved inthe operation, transport, maintenance and storage ofequipment.

1P15 Series Landscape Pull Type Rakes 302-223M

them. remove the key.▲ Detach and store implements in a

area where children normally donot play. Secure implement byusing blocks and supports.

OFF

REMOVE

2

Important Safety Information

LRP05 & LRP15 Series Landscape Pu

Land PrideTable of Contents

Use SafetyLights and Devices▲ Slow moving tractors, self-

propelled equipment, and towedimplements can create a hazardwhen driven on public roads. Theyare difficult to see, especially atnight.

▲ Flashing warning lights and turnsignals are recommendedwhenever driving on public roads.Use lights and devices providedwith implement.

Use A Safety Chain▲ A safety chain will help control

drawn machinery should itseparate from the tractordrawbar.

▲ Use a chain with the strengthrating equal to or greater thanthe gross weight of the towedmachinery.

▲ Attach the chain to the tractordrawbar support or otherspecified anchor location. Allowonly enough slack in the chain topermit turning.

▲ Do not use safety chain fortowing.

These are common practices that may or may not be applicable to the products described inthis manual.

TransportMachinery Safely▲ Comply with state and local laws.▲ Maximum transport speed for

implement is 20 mph. DO NOTEXCEED. Never travel at a speedwhich does not allow adequatecontrol of steering and stopping.Some rough terrains require aslower speed.

▲ Sudden breaking can cause atowed load to swerve and upset.

ll Type Rakes 302-223M

Reduce speed if towed load is notequipped with breaks.

▲ Use the following maximumspeed - tow load weight ratios asa guideline:

▲ 20 mph when weight is less thanor equal to the weight of tractor.

▲ 10 mph when weight is doublethe weight of tractor.

▲ IMPORTANT: Do not tow a loadthat is more than double theweight of tractor.

Practice SafeMaintenance▲ Understand procedure before

doing work. Use proper tools andequipment, refer to Operator’sManual for additional information.

▲ Work in a clean dry area.▲ Lower the implement to the

ground, put tractor in park, turn offengine, and remove key beforeperforming maintenance.

▲ Allow implement to coolcompletely.

▲ Do not grease or oil implementwhile it is in operation.

▲ Inspect all parts. Make sure partsare in good condition & installedproperly.

▲ Remove buildup of grease, oil ordebris.

▲ Remove all tools and unusedparts from before operation.

07/14/08

3

Important Safety Information

07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes 302-223M

Land Pride Table of Contents

Prepare for Emergencies▲ Be prepared if a fire starts.▲ Keep a first aid kit and fire

extinguisher handy.▲ Keep emergency numbers for

doctor, ambulance, hospital andfire department near phone.

911

WearProtective Equipment▲ Protective clothing and equipment

should be worn.▲ Wear clothing and equipment

appropriate for the job. Avoidloose fitting clothing.

▲ Prolonged exposure to loud noisecan cause hearing impairment orhearing loss. Wear suitablehearing protection such asearmuffs or earplugs.

▲ Operating equipment safelyrequires the full attention of theoperator. Avoid wearing radioheadphones while operatingmachinery.

Avoid HighPressure Fluids Hazard▲ Escaping fluid under pressure can

penetrate the skin causing seriousinjury.

▲ Avoid the hazard by relievingpressure before disconnectinghydraulic lines.

▲ Use a piece of paper orcardboard, NOT BODY PARTS, tocheck for suspected leaks.

▲ Wear protective gloves and safetyglasses or goggles when workingwith hydraulic systems.

▲ If an accident occurs, see adoctor immediately. Any fluidinjected into the skin must besurgically removed within a fewhours or gangrene may result.

These are common practices that may or may not be applicable to the products described inthis manual.

Keep RidersOff Machinery▲ Riders obstruct the operator’s

view, they could be struck byforeign objects or thrown from themachine.

▲ Never allow children to operateequipment.

Important Safety InformationLand PrideTable of Contents

Safety LabelsYour Landscape Rake comes equipped with all safety labels inplace. They were designed to help you safely operate your rake.

1. Read and follow label directions.2. Keep all safety labels clean and legible.3. Replace all damaged or missing labels.4. Some new equipment installed during repair require safety

labels to be affixed to the replaced component as specifiedby Land Pride. When ordering new components make surethe correct safety labels are included in the request. Toorder new labels go to your Land Pride dealer.

5. Refer to this section for proper label placement.To install new labels:a. Clean the area the label is to be placed.

b. Spray soapy water on the surface where label is to beplaced.

c. Peel backing from label. Press firmly on surface.

d. Squeeze out air bubbles with edge of a credit card.

4 LRP05 & LRP15 Series Landscape Pull Type Rakes 302-223M 07/14/08

838-529C

LRP05 & LRP15 Caution: Falling Rake orMoldboard Hazard

20997

818-230C

LRP15 Red Reflector20996

818-230C

LRP05 Red Reflector20996

IntroductionLand Pride Table of Contents

IntroductionLand Pride welcomes you to the growing family of newproduct owners. IMPORTANT: A special point of information related to

This Landscape Rake has been designed with care andbuilt by skilled workers using quality materials. Properassembly, maintenance, and safe operating practices willhelp you get years of satisfactory use from the rake.

The parts on your LRP05 & LRP15 Landscape Rakeshave been specially designed and should only be replacedwith genuine Land Pride parts. See your local Land PrideDealer for all your Landscape Rake replacement parts.

ApplicationThe LRP05 and LRP15 Series Landscape Rakes aredesigned and built by Land Pride to perform final soilsurface preparation and reshaping soil and/or aggregateprofile. LRP05 Series rakes are offered in 4, 5, and 6 ft.working widths with pull type hitches for mounting tocompact tractors in the 20hp range and ATV’s. LRP15Series rakes are offered in 5 ft. and 6 ft. working widthswith pull type hitches for mounting to tractors with 17 to35hp capabilities and ATV’s. Both series offer anglingcapabilities to meet specific finishing needs, and anoptional flip-down grader blade to expedite materialdistribution and contouring tasks.

These Land Pride Landscape Rakes are perfectly suitedfor use by home owners, landscapers, contractors, andrental yards. They have applications at housing and roadconstruction projects, golf courses, terracing sites, run-offcontrol projects, and reforestation sights. See “Featuresand Benefits” and “Product Specifications” for additionalinformation and performance enhancing options.

Using This Manual• This Operator’s Section is designed to help familiarize

you with safety, assembly, operation, adjustments,troubleshooting, and maintenance. Read this manualand follow the recommendations to help ensure safeand efficient operation.

• The information contained within this manual wascurrent at the time of printing. Some parts may changeslightly to assure you of the best performance.

• To order a new Operator or Parts Manual contact yourauthorized dealer. Manuals can also be downloaded,free-of-charge from our website at www.landpride.comor printed from the Land Pride Service & Support Centerby your dealer.

Terminology“Right” or “Left” as used in this manual is determined byfacing the direction the machine will travel while in useunless otherwise stated.

Definitions

Owner AssistanceThe Warranty Registration card should be filled out by thedealer at the time of purchase. This information isnecessary to provide you with quality customer service.

If customer service or repair parts are required contact aLand Pride dealer. A dealer has trained personnel, repairparts and equipment needed to service the LandscapeRake.

These parts have been specially designed and shouldonly be replaced with genuine Land Pride parts. Pleaseconsult you nearest Land Pride Dealer for replacementparts.

Serial Number PlateRefer to the Figure 1 for the location of your serialnumber plate on both LRP05 & LRP15 Series.

For prompt service always use the serial number andmodel number when ordering parts from your Land Pridedealer. Be sure to include your serial and model numbersin correspondence also.

Your dealer wants you to be satisfied with your newmachine. If for any reason you do not understand any partof this manual or are not satisfied with the servicereceived, the following actions are suggested:

1. Discuss the matter with your dealership ServiceManager. Make sure he is aware of any problems youmay have and that he has had the opportunity to assistyou.

2. If you are still not satisfied, seek out the Owner orGeneral Manager of the dealership, explain theproblem and request assistance.

3. For further assistance write to:

Product SupportLand Pride, Service Department

1525 East North StreetP.O. Box 5060

Salina, KS. 67402-5060

NOTE: A special point of information that Land Pridefeels an operator must be aware of before continuing.

its preceding topic. Land Pride’s intention is that thisinformation should be read and noted beforecontinuing.

20997

Serial Number Plate LocationFigure 1


Section 1: Assembly and Set-upLand PrideTable of Contents

Series LRP05 Landscape Rakes 5. Insert rear axle pivot lug (#3) between clevis lifting linksSection 1: Assembly and Set-up

Refer to Figure 1-1:1. Insert 1” rake pivot pin (#10) welded to pull frame (#5)

through pivot hole in rake assembly (#9) as shown.Secure with flat washer (#17), slotted hex nut (#15),and 7/32” x 2” cotter pin (#18). Tighten slotted nut to asnug fit. Do not torque slotted nut.

2. Insert 3/4” x 4 3/8” hitch pivot pin (#19) through weldedpull frame (#5) and secure with 3/16” hair pin (#20) asshown.

3. Position rear axle weldment (#7) between side plates ofrear axle pivot bracket (#2). Insert rear axle pivot shaft(#4) through rear axle pivot bracket and rear axleweldment (#2 & #7) as shown. Secure with 1/4” x 1 3/4”hex bolts (#12) and lock nuts (#13). Tighten to propertorque.

4. Assemble lift handle (#8) to pull frame (#5) and securewith cotter pin (#23) as shown.

6 LRP05 & LRP15 Series Landscape Pull Type Rakes 302-2

LR05 AssemblFigure 1-1

20994

(#6). Secure with 5/8” x 2 1/4” hex bolt (#11) and locknut (#14) as shown. Tighten to a snug fit. Do not torquelock nut.

6. Attach Wheels (#22) to rear axle weldment (#7) andsecure with flat washers (#16) and 5/32” x 1 3/4” cotterpins (#21).

7. Ropes (#1) are coiled and attached to lift handle (#9).Uncoil ropes when ready to use.

! CAUTION!Always check to be sure that the slotted hex nut and cotter pin arein place to retain the rake before reversing the rake. If they aremissing, the rake will fall off the frame while being rotated!

23M 07/14/08

y

Section 1: Assembly and Set-upLand Pride Table of Contents

Series LRP15 Landscape RakesRefer to Figure 1-2:1. Insert 1” rake pivot pin (#7) welded to pull frame (#4)

through pivot hole in rake assembly (#3) as shown.Secure with flat washer (#16), slotted hex nut (#13)and 7/32” X 2” cotter pin (#17). Tighten slotted nut to asnug fit. Do not torque slotted nut.

2. Insert 3/4” x 4 3/8” hitch pivot pin (#19) through weldedpull frame (#4) and secure with 3/16” hair pin (#20) asshown.

3. Position rear axle weldment (#5) between pull frameyoke arms (#4). Insert rear pull axle shaft (#2) throughpull frame yoke arms (#4) and rear axle weldment (#5)as shown. Secure both left and right side of rear axleweldment (#5) with 3/8” x 1 3/4” hex bolts (#9) and locknuts (#11). Tighten to proper torque.

4. Assemble lift handle (#6) to pull frame (#4) and securewith cotter pin (#22) as shown.

5. Insert free end of turn buckle assembly (#8) around theaxle connecting link (#1). Secure with 5/8” x 2 1/2” hexbolt (#10) and nylock nut (#14) as shown. Tighten to asnug fit. Do not torque lock nut.

6. Attach Wheels (#21) to rear axle weldment (#5) andsecure with lock washers (#15) and hex nuts (#12).Torque to proper torque.

! CAUTION!Always check to be sure that the slotted hex nut and cotter pin arein place to retain the rake before reversing the rake. If they aremissing, the rake will fall off the frame while being rotated!


LRP15 AssemblyFigure 1-2

21001

Section 1: Assembly and Set-upLand PrideTable of Contents

LRP05 Grader Blade (Optional)Refer to Figure 1-31. Attach blade support arms (#2) to the right and left

hand side of rake mount (#1) with 3/8” x 2 1/4” hexbolts (#7), 3/8” lockwashers (#14), and 3/8” hex nuts(#9) (four bolts per support arm). Tighten to propertorque.

2. Attach Blade-up Lock Pin (#15) to right and left handBlade Support Arms with hair pin (#16) as shown.

3. Attach both right and left end of the Grader Blade (#4)to Blade Support Arms (#2) with 3/4” x 2 1/2” grade 5hex bolts (#8) and locknuts (#10) as shown. Do nottorque locknuts (#10).

4. Attach two hex coupler nuts (#11) with flat washer (#13)to each side plate weldment (#3) by inserting two 7/16”x 1” grade 5 hex bolts (#6) complete with lock washers(#12), and flat washers (#13) through each side platebottom and top holes as shown. Do not torque.

5. Insert pivot pin (#5) welded to side plates (#3) throughtubes located on both ends behind Grader Blade (#4).Make certain coupler nuts (#11) are positioned behindthe grader blade. Secure with hair pins (#16).

6. Adjust hex coupler nuts (#11) against back side ofgrader blade and tighten bolts (#6) to proper torque.


LRP05 Grader Blade AssemblyRight Hand Side Shown

Figure 1-3

21014

Section 1: Assembly and Set-upLand Pride Table of Contents

LRP15 Grader Blade (Optional)Refer to Figure 1-41. Attach blade support arms (#16) to the right and left

hand side of the rake mount (#20) with 3/8” x 2 3/4”hex bolts (#17), 3/8” lockwashers (#18), and 3/8” hexnuts (#19) (six bolts per support arm). Tighten toproper torque.

2. Attach Blade Lock Handle (#3) to the right and left handBlade Support Arms with 1/2” x 3” grade 5 hex bolts(#2), lock washers (#14), and hex nuts (#15) as shown.Tighten to proper torque.

3. Insert pin (#1) through the top hole of both BladeSupport Arms. Secure with attached hair pin (#9).

4. Attach both the right and left end of the Grader Blade(#11) to Blade Support Arm with 3/4” x 2 1/2” grade 5hex bolts (#12) and locknuts (#13) as shown. Do nottorque locknut (#13).

5. Attach two hex coupler nuts (#8) with flat washer (#6) toeach side plate (#7) by inserting two 7/16” x 1” grade 5hex bolts (#4) complete with lock washers (#5), and flatwashers (#6) through each side plate bottom and topholes as shown. Do not torque until step 3.

6. Insert pivot pin welded to side plates (#7) through thetubes located on both ends behind the Grader Blade(#11). Make certain that the coupler nuts (#8) arepositioned behind the grader blade. Secure with hairpins (#9)

7. Adjust hex coupler nuts (#8) against back side of graderblade and tighten bolts (#4) to proper torque.


LRP15 Grader Blade AssemblyRight Hand Side Shown

Figure 1-4

20993

Section 2: Operating InstructionsLand PrideTable of Contents

Section 2: Operating Instructions
Operating InstructionsBy now you should have thoroughly read your Operator’sManual and properly installed your Land Pride LandscapeRake to your tractor. Before you begin raking you shouldvisually survey the work site to make sure it is safe andfree of foreign obstacles. Also make certain that allirrigation heads, utility outlets, and other obstacles areproperly marked.
Please stop and do the above checks and preparations ifyou have not yet done so before you begin to rake. This isa must for your safety and for the safety of others.

Now that you are properly briefed, your landscape rake isproperly installed, and you have properly checked out yourwork site, it is time to begin raking. When transporting ortravelling to and from work sites, make sure that the rake isin the fully raised position and not in contact with theground. Select a safe speed and transport to your worksite in such a manner that faster moving vehicles can passyou safely. A slow moving vehicle sign should beemployed if you are using a public road or right-of way.

Once you have safely arrived at your work site, stop thetractor, lock tractor brakes to prevent rolling, shut offtractor engine, and remove ignition key beforedismounting. Adjust rake angle with the rake in the upposition.

• Changing rake angle left or right will distributeextraneous and oversized material in furrows to the leftor right.

• Adjusting rake angle to be straight across distributesmaterial evenly across the width of the rake with slightfurrowing produced at both ends of the rake.

• Set rake height by adjusting the control lever to the rearnotch if you are ready to begin work. If not, leave therake in the up position.

Remount tractor to make a gear and engine rpm selectionthat will produce a safe suitable ground speed for yourparticular operating conditions.

Begin working with the rake set in the lowered positionunless you intend to travel a short distance without raking.In this situation, leave the rake up to travel and begin workby pulling on the handle to lower the rake. See RakeHeight Adjustment in Section 3 on page 11 for a detaileddescription on using pull ropes for the LRP05.

Additional adjustments may be required to achieve thedesired affect you are wanting. Practice will help toconsistently achieve that desired result you are after.

Always keep safety uppermost in your mind andremember that before dismounting the tractor you mustalways set the park brake, turn off the tractor and removethe ignition key. If you must park on a hillside you shouldalways chock the tractor wheels for an extra measure ofsafety. See “Product Specifications” on page 15 and“Features and Benefits” on page 16 for additionalinformation on performance enhancing options.


Section 3: AdjustmentsLand Pride Table of Contents

Section 3: AdjustmentsLRP05 & LRP15 Rake Angle Raise the rake by first pulling on rope (#6) or by squeezing

Refer to Figure 3-1:Five holes are provided for angling the rake position eitherclockwise or counterclockwise in increments of 7 1/2degrees for a total of 15 degrees either direction off center.

Change rake angle by pulling hair pin (#1) from lock pin(#2), pull lock pin (#2) from pull frame (#3), and rotate rakeframe(#4). Reset lock pin and hair pin after rotating rakeframe.

LRP05 & LRP15 Lever Height ControlRefer to Figure 3-1:There are three notches in the height adjusting plate (#5)for lowering and raising the rake. The rear notch sets therake in its lowest position, the center notch raises the rakehalfway up, and the front notch raises the rake all the wayup.

LRP05 Series are equipped with pull ropes to allow heightadjustment from the tractor seat. LRP15 Series are notequipped with pull ropes due to weight of the rakeelements. Pull ropes can be added to LRP15 rakes by theuser.

Rake AnglingSeries LRP05 Shown

Figure 3-1

20998

07/14/08 LRP05

handle (#9) upward to release pressure induced by thespring loaded latch (#8) resting in the rear notch. Keepingrope (#6) tight, pull on rope (#7) to raise the spring loadedlatch and continue pulling on rope (#7) to raise the rake.

Lower the rake by pulling on rope (#6) to release pressureinduced by the spring loaded latch (#8) resting against thefront notch. Keeping rope (#6) tight, pull on rope (#7) toraise the spring loaded latch (#8) and slowly allow the raketo lower by keeping rope (#7) tight as the operatorreleases the rope slowly till spring loaded latch (#8)returns to the rear notch. Letting go of the rope too fast willcause the spring latch (#8) to catch in the middle notchinstead of the rear notch.

Use middle notch in the adjusting plate (#5) for makingturns and gently dumping the load on the go.

LRP15 Turnbuckle Height ControlRefer to Figure 1-2 on page 7:Fine tune the LRP15 rake height by adjusting the turnbuckle (#9) connecting the Lift Handle Arm (#7) to the rearaxle weldment (#6).

11 & LRP15 Series Landscape Pull Type Rakes 302-223M

Section 3: AdjustmentsLand PrideTable of Contents

LRP05 Flip Down Grader Blade(Optional)Refer to Figure 3-2The LRP05 grader blade (#1) may be stored in the upposition when not in use. Remove hair pin (#2) and blade-up lock pin (#3) located in the blade support arms (#4).Carefully pivot blade up until hole (#5) in blade supportbars align with blade-up lock pin holes (#6). Replaceblade-up lock pins and hair pins.

Lower grader blade by first removing hair pins (#2) fromblade-up lock pins (#3). Support grader blade in the upposition and remove blade-up lock pins (#3) Lower graderblade. Replace blade-up lock pins and hair pins in bladesupport arms (#4).

12 LRP05 & LRP15 Series Landscape Pull Type Rakes 302-2

LRP05 Grader Blade Lock Up PositionFigure 3-2

21015

LRP15 Flip Down Grader Blade(Optional)Refer to Figure 3-3:The LRP15 grader blade may be stored in the up positionwhen not in use. Carefully pivot the blade upward until itcontacts the blade lock handles (#1). A lock pin (#2)should be placed in the lower hole to insure that the graderblade remains securely in the raised position.

Lower the blade by removing the lock pin from the lowerhole and replace in upper hole. Pull blade lock handle (#1)to allow grader blade to flip down. Replace lock pin tostore it for future use.

LRP15 Grader Blade Lock Up PositionFigure 3-3

20999

23M 07/14/08

Section 4: Maintenance and LubricationLand Pride Table of Contents

Section 4: Maintenance and LubricationMaintenance
GeneralProper service and adjustment is the key to long life of any implement. With careful and systematic inspection andlubrication you can avoid many costly repairs and downtime.
Lubrication

07/14/08 LRP05 &

50multi-purposespray lube

multi-purposegrease lube

multi-purposeoil lube

Intervals at whichlubrication is required

LubricationLegend

25

20998

20996

20996

20996

LRP05 & LRP15 Lever Arm Pivot Point(LRP05 shown)

Grease lever pivot zerk every 25 hours.

Type of Lubrication: Multi-PurposeQuantity = Until grease begins to emerge.

25

LRP15 Rear Axle WeldmentGrease rear axle weldment every 25 hours.

Type of Lubrication: Multi-PurposeQuantity = Generously

25

Rear Wheel BearingsGrease rear wheel bearings every 25 hours.

Type of Lubrication: Multi-Purpose

Quantity = Generously

Seasonally

Rake TeethGrease before extended non-use or seasonally.

Type of Lubrication: Multi-PurposeQuantity = Generously

13 LRP15 Series Landscape Pull Type Rakes 302-223M

Section 5: OptionsLand PrideTable of Contents

Section 5: Options

LRP05 & LRP15 Flip Down Grader BladeNote: LRP05 & LRP15 grader blade assemblies are complete with side plates and Mounting Arms.

302-236A LRP0548 GRADER BLADE






Section 6: Specifications & CapacitiesLand Pride Table of Contents

Section 6: Specifications & Capacities


LRP05 &LRP15 Series Landscape Pull Type Rakes

LRP0548 LRP0560 LRP0572 LRP1560 LRP1572

Rake Width 48” 60” 72” 60” 72”

ApproximateWeight (lbs.)

Pull Type

98 115 123 218 248

HorsepowerRating

15-20 15-20 15-20 20-35 20-35

Rake Height 12” 12” 12” 16 1/2” 16 1/2”

Teeth Size 1/4” x 3/4”wide

1/4” x 3/4”wide

1/4” x 3/4”wide

5/16” x 1” wide 5/16” x 1” wide

Angle andPosition

5 Positions Up to 30 degrees Right or left 5 Positions Up to 30 degrees Right orLeft

Teeth Spacing 1 3/4” Centers 2” Centers

Teeth Material High Carbon Spring Steel High Carbon Spring Steel

Grader BladeOption

Flip Down Self Supporting Grader Blade with Blade-upLocking Handles and locking pins

Flip Down Self Supporting GraderBlade with Blade-up Locking Handles

and locking pins

Section 7: Features and BenefitsLand PrideTable of Contents

Section 7: Features and Benefits


LRP05 &LRP15 Series Landscape Pull Type RakesFeatures Benefits

Tractor HP range LRP05 = 15 - 20 HPLRP15 = 20 - 35 HP

Various working widths Allows adaptability to many tractor sizes.LRP05 = 48”, 60” & 72”LRP15 = 60” & 72”

5 Forward angles(up to 30 degrees)

Vary how much material to move.

High carbon spring steel teeth Teeth have “memory” to spring back to shape.

Individual Replaceable teeth Replace a damaged tooth without removing all of the teeth.

Optional Grader Blade Adding a flip down grader blade allows one to move and level dirt as well as othermaterials.

Moldboard Blade adaptable Moldboard Blade assembly can easily replace the rake assembly for more versatility toones implement.

Pull Type Use with tractors, ATV’s, utility vehicles, and golf carts.

Turnbuckle (LRP15 Only) Ease of depth control.

Section 8: AppendixLand Pride Table of Contents

Section 8: Appendix

Torque Values Chart

in-tpi 1 N · m ft-lb 3 N · m ft-lb N · m ft-lb mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb1/4" - 20 7.4 5.6 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7

1/4" - 28 8.5 6 13 10 18 14 M 6 X 1 7 5 11 8 15 11

5/16" - 18 15 11 24 17 33 25 M 8 X 1.25 17 12 26 19 36 27

5/16" - 24 17 13 26 19 37 27 M 8 X 1 18 13 28 21 39 29

3/8" - 16 27 20 42 31 59 44 M10 X 1.5 33 24 52 39 72 53

3/8" - 24 31 22 47 35 67 49 M10 X 0.75 39 29 61 45 85 62

7/16" - 14 43 32 67 49 95 70 M12 X 1.75 58 42 91 67 125 93

7/16" - 20 49 36 75 55 105 78 M12 X 1.5 60 44 95 70 130 97

1/2" - 13 66 49 105 76 145 105 M12 X 1 90 66 105 77 145 105

1/2" - 20 75 55 115 85 165 120 M14 X 2 92 68 145 105 200 150

9/16" - 12 95 70 150 110 210 155 M14 X 1.5 99 73 155 115 l215 160

9/16" - 18 105 79 165 120 235 170 M16 X 2 145 105 225 165 315 230

5/8" - 11 130 97 205 150 285 210 M16 X 1.5 155 115 240 180 335 245

5/8" - 18 150 110 230 170 325 240 M18 X 2.5 195 145 310 230 405 300

3/4" - 10 235 170 360 265 510 375 M18 X 1.5 220 165 350 260 485 355

3/4" - 16 260 190 405 295 570 420 M20 X 2.5 280 205 440 325 610 450

7/8" - 9 225 165 585 430 820 605 M20 X 1.5 310 230 650 480 900 665

7/8" - 14 250 185 640 475 905 670 M24 X 3 480 355 760 560 1050 780

1" - 8 340 250 875 645 1230 910 M24 X 2 525 390 830 610 1150 845

1" - 12 370 275 955 705 1350 995 M30 X 3.5 960 705 1510 1120 2100 1550

1-1/8" - 7 480 355 1080 795 1750 1290 M30 X 2 1060 785 1680 1240 2320 1710

1 1/8" - 12 540 395 1210 890 1960 1440 M36 X 3.5 1730 1270 2650 1950 3660 2700

1 1/4" - 7 680 500 1520 1120 2460 1820 M36 X 2 1880 1380 2960 2190 4100 3220

1 1/4" - 12 750 555 1680 1240 2730 2010 1 in-tpi = nominal thread diameter in inches-threads per in.

1 3/8" - 6 890 655 1990 1470 3230 2380 2 N· m = newton-meters

1 3/8" - 12 1010 745 2270 1670 3680 2710 3 ft-lb= foot pounds

1 1/2" - 6 1180 870 2640 1950 4290 3160 4 mm x pitch = nominal thread diameter in millimeters xthread pitch1 1/2" - 12 1330 980 2970 2190 4820 3560

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

Grade 2 Grade 5 Grade 8

Bolt Head Identification

Bolt Size(Inches) Class 5.8 Class 8.8 Class 10.9

Bolt Head Identification

Bolt Size(Metric)

5.8 8.8 10.9


Section 8: AppendixLand PrideTable of Contents

Notes


Section 8: Appendix

07/14/08

Land Pride Table of Contents

WarrantyLand Pride warrants to the original purchaser that this Land Pride product will

be free from defects in material and workmanship beginning on the date ofpurchase by the end user according to the following schedule when used asintended and under normal service and conditions for personal use.

Overall Unit: One year Parts and Labor

Rake Teeth: Considered wear items

This Warranty is limited to the replacement of any defective part by Land Prideand the installation by the dealer of any such replacement part, and does not covercommon wear items such as blades, belts, tines, etc. Land Pride reserves the rightto inspect any equipment or parts which are claimed to have been defective inmaterial or workmanship.

This Warranty does not apply to any part or product which in Land Pride’sjudgment shall have been misused or damaged by accident or lack of normalmaintenance or care, or which has been repaired or altered in a way whichadversely affects its performance or reliability, or which has been used for apurpose for which the product is not designed. Misuse also specifically includesfailure to properly maintain oil levels, grease points, and driveline shafts.

Claims under this Warranty must be made to the dealer which originally soldthe product and all warranty adjustments must be made through such dealer. LandPride reserves the right to make changes in materials or design of the product atany time without notice.

This Warranty shall not be interpreted to render Land Pride liable for damagesof any kind, direct, consequential, or contingent to property. Furthermore, LandPride shall not be liable for damages resulting from any cause beyond itsreasonable control. This Warranty does not extend to loss of crops, any expenseor loss for labor, supplies, rental machinery or for any other reason.

No other warranty of any kind whatsoever, express or implied, is madewith respect to this sale; and all implied warranties of merchantability andfitness for a particular purpose which exceed the obligations set forth in thiswritten warranty are hereby disclaimed and excluded from this sale.

This Warranty is not valid unless registered with Land Pride within 30 days fromthe date of purchase by the end user.

19LRP05 & LRP15 Series Landscape Pull Type Rakes 302-223M

Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

www.landpride.com

Table of Contents Landscape Pull Type Rakes › ... › 302-223m.pdf · 07/14/08 LRP05 & LRP15...

Documents

Transcript of Table of Contents Landscape Pull Type Rakes › ... › 302-223m.pdf · 07/14/08 LRP05 & LRP15...