SVENSK STANDARD

Fastställd/Approved: 2017-02-01Publicerad/Published: 2017-02-06Utgåva/Edition: 1Språk/Language: engelska/EnglishICS: 77.140.70

SS-EN 10365:2017

Varmvalsade U-, I- och H-profiler av stål – Mått och vikt

Hot rolled steel channels, I and H sections – Dimensions and masses

This preview is downloaded from www.sis.se. Buy the entireThis preview is downloaded from www.sis.se. Buy the entireThis preview is downloaded from www.sis.se. Buy the entireThis preview is downloaded from www.sis.se. Buy the entirestandard via https://www.sis.se/std-8024824standard via https://www.sis.se/std-8024824standard via https://www.sis.se/std-8024824standard via https://www.sis.se/std-8024824

Standarder får världen att fungeraSIS (Swedish Standards Institute) är en fristående ideell förening med medlemmar från både privat och offentlig sektor. Vi är en del av det europeiska och globala nätverk som utarbetar internationella standarder. Standarder är dokumenterad kunskap utvecklad av framstående aktörer inom industri, näringsliv och samhälle och befrämjar handel över gränser, bidrar till att processer och produkter blir säkrare samt effektiviserar din verksamhet.

Delta och påverkaSom medlem i SIS har du möjlighet att påverka framtida standarder inom ditt område på nationell, europeisk och global nivå. Du får samtidigt tillgång till tidig information om utvecklingen inom din bransch.

Ta del av det färdiga arbetetVi erbjuder våra kunder allt som rör standarder och deras tillämpning. Hos oss kan du köpa alla publikationer du behöver – allt från enskilda standarder, tekniska rapporter och standard-paket till handböcker och onlinetjänster. Genom vår webbtjänst e-nav får du tillgång till ett lättnavigerat bibliotek där alla standarder som är aktuella för ditt företag finns tillgängliga. Standarder och handböcker är källor till kunskap. Vi säljer dem.

Utveckla din kompetens och lyckas bättre i ditt arbeteHos SIS kan du gå öppna eller företagsinterna utbildningar kring innehåll och tillämpning av standarder. Genom vår närhet till den internationella utvecklingen och ISO får du rätt kunskap i rätt tid, direkt från källan. Med vår kunskap om standarders möjligheter hjälper vi våra kunder att skapa verklig nytta och lönsamhet i sina verksamheter.

Vill du veta mer om SIS eller hur standarder kan effektivisera din verksamhet är du välkommen in på www.sis.se eller ta kontakt med oss på tel 08-555 523 00.

Standards make the world go roundSIS (Swedish Standards Institute) is an independent non-profit organisation with members from both the private and public sectors. We are part of the European and global network that draws up international standards. Standards consist of documented knowledge developed by prominent actors within the industry, business world and society. They promote cross-border trade, they help to make processes and products safer and they streamline your organisation.

Take part and have influenceAs a member of SIS you will have the possibility to participate in standardization activities on national, European and global level. The membership in SIS will give you the opportunity to influence future standards and gain access to early stage information about developments within your field.

Get to know the finished workWe offer our customers everything in connection with standards and their application. You can purchase all the publications you need from us - everything from individual standards, technical reports and standard packages through to manuals and online services. Our web service e-nav gives you access to an easy-to-navigate library where all standards that are relevant to your company are available. Standards and manuals are sources of knowledge. We sell them.

Increase understanding and improve perceptionWith SIS you can undergo either shared or in-house training in the content and application of standards. Thanks to our proximity to international development and ISO you receive the right knowledge at the right time, direct from the source. With our knowledge about the potential of standards, we assist our customers in creating tangible benefit and profitability in their organisations.

If you want to know more about SIS, or how standards can streamline your organisation, please visit www.sis.se or contact us on phone +46 (0)8-555 523 00

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

© Copyright / Upphovsrätten till denna produkt tillhör SIS, Swedish Standards Institute, Stockholm, Sverige. Användningen av denna produkt regleras av slutanvändarlicensen som återfinns i denna produkt, se standardens sista sidor.

© Copyright SIS, Swedish Standards Institute, Stockholm, Sweden. All rights reserved. The use of this product is governed by the end-user licence for this product. You will find the licence in the end of this document.

Upplysningar om sakinnehållet i standarden lämnas av SIS, Swedish Standards Institute, telefon 08-555 520 00. Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard.

Information about the content of the standard is available from the Swedish Standards Institute (SIS), telephone +46 8 555 520 00. Standards may be ordered from SIS Förlag AB, who can also provide general information about Swedish and foreign standards.

Europastandarden EN 10365:2017 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN 10365:2017.

The European Standard EN 10365:2017 has the status of a Swedish Standard. This document contains the official English version of EN 10365:2017.

Denna standard är framtagen av kommittén för Konstruktionsstål, SIS / TK 142.

Har du synpunkter på innehållet i den här standarden, vill du delta i ett kommande revideringsarbete eller vara med och ta fram andra standarder inom området? Gå in på www.sis.se - där hittar du mer information.

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM

EN 10365 January 2017

ICS 77.140.70 English Version Hot rolled steel channels, I and H sections - Dimensions and masses Profilés en U en aciers laminés à chaud, poutrelles I et H - Dimensions et masses Warmgewalzter U-Profilstahl, I- und H-Träger - Maße und Masse

This European Standard was approved by CEN on 14 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T É E U R O P É E N D E N O R M A L I S A T I O N E U R O P Ä I S C H E S K O M I T E E F Ü R N O R M U N G CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10365:2017 E

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

2

Contents Page

European foreword ....................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 5

4 Designation........................................................................................................................................................ 5

5 Dimensions and masses ................................................................................................................................ 5

6 Tolerances on dimensions, shape and mass ......................................................................................... 7

7 Material ............................................................................................................................................................... 7

Annex A (informative) Comparison of symbols used in this document with those in EN 1993-1-1 .................................................................................................................................................... 32

Bibliography ................................................................................................................................................................. 33

SS-EN 10365:2017 (E)

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

3

European foreword

This document (EN 10365:2017) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements”, the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the latest by July 2017.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This project was submitted to the Enquiry under reference prEN 16828.

According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

SS-EN 10365:2017 (E)

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

4

1 Scope

This European standard specifies the nominal dimensions and masses of the hot rolled steel channels, I and H sections.

The following shapes are covered by this standard:

Sections:

— Parallel flange I sections IPE;

— Wide flange beams HE;

— Extra wide flange beams HL and HLZ;

— Wide flange columns HD;

— Wide flange bearing piles HP and UBP;

— Universal beams UB;

— Universal columns UC;

— Taper flange I sections IPN and J.

Channels:

— Parallel flange channels UPE and PFC;

— Taper flange channels UPN, U and CH.

These requirements do not apply to hot rolled steel channels, I and H sections from stainless steel.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

EN 10024, Hot rolled taper flange I sections - Tolerances on shape and dimensions

EN 10025-1, Hot rolled products of structural steels - Part 1: General technical delivery conditions

EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels

EN 10025-3, Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels

EN 10025-4, Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels

EN 10025-5, Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance

EN 10034, Structural steel I and H sections - Tolerances on shape and dimensions

SS-EN 10365:2017 (E)

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

5

EN 10079, Definition of steel products

EN 10279, Hot rolled steel channels - Tolerances on shape, dimensions and mass

3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 10079 apply.

4 Designation

A section shall be designated according to Tables 1 to 15.

This form of designation shall be used in any enquiry and order.

5 Dimensions and masses

Hot rolled steel channels, I and H sections complying with this European Standard shall be manufactured with the specified dimensions given in the Table 1 to 15 and according to Figures 1 to 4 below.

Radii of fillets and toes of shape profiles vary with individual manufacturers and therefore are not specified.

The masses per unit length specified in Tables 1 to 15 were calculated on the basis of a density of 7850 kg/m3.

Figure 1 — IPE, HE, HL, HD, HP, UBP, UB and UC parallel flange sections

SS-EN 10365:2017 (E)

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

6

Figure 2 — Taper flange I sections IPN, J and extra wide flange beams HLZ

Figure 3 — Parallel flange channels UPE and PFC

Figure 4 — Taper flange channels UPN, U and CH

SS-EN 10365:2017 (E)

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824

7

6 Tolerances on dimensions, shape and mass

Tolerances on dimensions, shape and mass shall be as given in EN 10034 for I (parallel flanges) and H sections.

Tolerances on dimensions, shape and mass shall be as given in EN 10024 for taper flange I sections.

Tolerances on dimensions, shape and mass shall be as given in EN 10279 for channels.

Tolerances for shapes not included in the mentioned standards shall be as agreed upon between the manufacturer and the purchaser.

7 Material

Sections and channels shall preferably be made from steel of a grade as specified in EN 10025-1, EN 10025-2, EN 10025-3, EN 10025-4 and EN 10025-5. Other steel grades as specified in EN 10225, EN 10028-2 and EN 10273 may also be used for specific applications.

The desired steel grade shall be specified at the time of ordering.

SS-EN 10365:2017 (E)

This preview is downloaded from www.sis.se. Buy the entire standard via https://www.sis.se/std-8024824