DIRECTIONS FOR USE

1. Apply Spill TACKLE absorbent onto the spill

2. Stir in a circular motion using a brush or broom

3. If slippery residue remains, re-apply.

4. Sweep encapsulated liquid into a dustpan

5. Dispose of properly in accordance with federal, state and local laws.

SUPERIOR ABSORPTION TO PREMIUM CLAY PRODUCTS

5244 A Avenue, Long Beach, MS 39560 | 228.206.1449| www.TACKLETechnologies.com

09/26/2014

MR KEITH FULTON TACKL TECHNOLOGIES 5244 A AVENUE LONG BEACH MS 39560 RE: Waste Certification Tackl Absorbent Dear MR. FULTON: The Alabama Department of Environmental Management has reviewed your waste certification received on 09/24/2014 and has assigned a Certification Number for this waste as shown below.

Waste Profile #: 140688 Tackl Technologies LLC Certification #: SW-093016-0076 Baldwin County Expiration Date of Certification: 09/30/2016

In your certification you requested one or more landfills be approved to receive your waste. Based on our review of the waste and the landfills requested, the waste is approved for disposal in the following landfills: Magnolia Sanitary Landfill 02-03

You should provide this approval letter to the landfill(s) listed above and contact the landfill to determine any special handling requirements for this waste prior to delivery to the landfill. According to ADEM regulations, the landfill may not receive this waste unless it has received a waste certification approval. For waste generated on a routine basis (not a one-time occurrence), another written certification for this waste stream should be submitted to ADEM prior to the expiration date listed above or at any time the process producing the waste changes. Each submittal should include a completed Solid Waste Profile Sheet, any supporting documentation including current analytical, and the appropriate fee. Current analytical consists of analysis performed within the past six months. If at any time before the expiration date of this certification, new analysis of the waste is performed, the new results will supersede any prior analysis from the time the samples are taken. If the new analysis indicates the waste is still non-hazardous, the waste may continue to be disposed of at the landfill listed above until the expiration date of this certification. If the new analysis indicates the waste is hazardous, this certification is revoked. Each time new analysis is performed on the waste, copies of the analytical results should be provided to ADEM and the landfill until this certification expires. The generator should not dispose of the waste prior to the receipt and review of the sampling results. Furthermore, this approval letter does not exempt Tackl Technologies LLC from complying with all applicable requirements of the ADEM Administrative Code. If you have any questions concerning this approval or the approval process, please contact Ms. Blake B. Pruitt at 334-271-7756. Sincerely,

Ronald T. Shell, Chief Environmental Services Branch RTS/sh

Notice of Certification / Application ID: 3445 December 01, 2012 Keith Fulton Environmental Research Company 5244 A Ave Long Beach, MS 39560-9705 Dear Keith Fulton, On behalf of the United States Department of Agriculture's (USDA's) BioPreferred® program, I am pleased to inform you that your application for use of the USDA Certified Biobased Product Label for TACKL Technologies Absorbent has been approved as of December 01, 2012. The test results for your product indicate the percentage of biobased content to be 98%. The Label remains in effect as long as the product or package is manufactured and marketed in accordance with the approved application and requirements of §2904.5 (i.e. Code of Federal Regulations for the Voluntary Labeling Program for Biobased Products); unless one of these occur:

1. Product or package reformulation: The product or package formulation of the certified product is changed such that the biobased content is reduced to a level below that reported in the approved application. When products have been reformulated, a new application for certification must be submitted in order to resume using the USDA Certified Biobased Product Label; and/or,

2. New minimum biobased content: USDA revises the minimum biobased content required for a product or package to be eligible to display the certification mark and the product or package does not meet the revised minimum. USDA will inform you that your certification is no longer valid. In this case, you must increase the biobased content of your product to be at or above the revised minimum and re-apply for certification within 60 days in order to continue to use the certification mark.

This email is your official notice of biobased product certification. Please print and save this email should you need to provide certification documentation to any entity.

The BioPreferred program looks forward to a long and successful partnership with you in the promotion of biobased products.

If you have additional questions or would like further information, you may call the BioPreferred Program Information Line (877) 251-6522 or email us at biobasedlabel@dm.usda.gov. Sincerely, Kate Lewis Deputy Manager USDA BioPreferred Program

TACKL Absorbent Safety Data Sheet

12/17/2012 EN (English) 1/6

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier Product form : Mixture Product name. : TACKL Absorbent

1.2. Relevant identified uses of the substance or mixture and uses advised against Use of the substance/preparation : Cleaning/Absorbent No additi onal infor mati on available

1.3. Details of the supplier of the safety data sheet TACKL Technologies 5244 A Avenue Long Beach, MS 39560

1.4. Emergency telephone number T 228-206-1449

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

GHS-US classification Not classified

2.2. Label elements

GHS-US labelling No labelling applicable

2.3. Other hazards No additional information available

SECTION 3: Composition/information on ingredients

3.1. Substances Not applicable

3.2. Mixtures

Name Product identifier % GHS-US classification Cellulose pulp (CAS No.) 65996-61-4 99 Not classified

SECTION 4: First aid measures

4.1. Description of first aid measures First-aid measures general : No special measures required. First-aid measures after inhalation : Remove to fresh air. If breathing is difficult, administer oxygent. Seek

medical attention. First-aid measures after skin contact : Wash with plenty of soap and water. First-aid measures after eye contact : If in eyes: Rinse cautiously with water for several minutes. Remove contact

lenses, if present and easy to do. Continue rinsing.