Stego accessories for cabinets Heating page ● Small semiconductor Heater RC 016 2 ● Touch-Safe Small Heater CSK 060 3 ● Semiconductor Heater HG 140 4 ● Hazardous area Heater CREx 020 5 ● Touch-Safe Heater CS 060 6 ● Touch-Safe Heater CSF 060 7 ● Compact semiconductor Fan Heater CS 028/CSL 028 8 ● Compact Fan Heater Series HGL 046 9Ventilating ● Roof Filter Fan RFP 018 10Regulating ● Small, compact Thermostat KTO 011 / KTS 011 11 ● Tamperproof Thermostats (Pre-set) FTO 011 / FTS 011 12 ● Dual Thermostat ZR 011 13 ● Hazardous area Thermostat REx 011 14Lighting ● Lamp Series LED 025 15-16Accessories ● Electrical Socket SD 035 17

www.klinkmann.com

2

Small semiconductor Heater RC 016 Series 8W, 10W, 13W

Wide voltage rangeDynamic heating upEnergy savingCompact

These small heaters are designed to prevent condensation and to ensure a mini-mum operating temperature in small enclosures.

Heat

ing

Technical Data

Operating voltage 120-240V AC/DC* (min. 110V, max. 265V)Heating element PTC resistor, temperature limitingHeater body aluminium, anodisedMounting screw fixingFitting position variableOperating/Storage temperature -45 to +70°C (-49 to +158°F)Operating/Storage humidity max. 90 % RH (non-condensing)Protection type / Protection class IP54 / II (double insulated)Approvals VDE + UL File No. E150057Note other voltages on request

Example of connection

Thermostat KTO 011(contact breaker, normally closed)

Art. No. Heatingcapacity*

Inrush current max.

Pre-fuseT (time-delay)

Surface temperature

(approx.)

Connection Weight (approx.)

01602.0-00 8W 2.0A 1A 150°C 2 x AWG 18 stranded wire 20g01609.0-00 10W 2.5A 2A 155°C 2 x AWG 22 sheathed cable (silicone) 30g01610.0-00 13W 3.0A 2A 170°C 2 x AWG 22 sheathed cable (silicone) 40g

LN

Art. No. 01610.0-00: Connection 2 x AWG 22 sheathed cable (silicone)

Art. No. 01609.0-00: Connection 2 x AWG 22 sheathed cable (silicone)

Art. No. 01602.0-00: Connection 2 x AWG 18 stranded wire

Heater RC 016

*Operating with voltages below 140V AC/DC reduces heating performance by approx. 10%.

*at 20°C (68°F) ambient temperature

3

Touch-Safe Small Heater CSK 060 Series 10W, 20W(Semiconductor)

Low surface temperatureDouble insulated (plastic housing)Wide voltage rangeDynamic heating upClip fixing

The heaters are used in enclosures where condensation is to be prevented or the temperature may not fall below a minimum value. In this way corrosion is avoided and an even temperature is ensured. The heaters are designed for permanent operation.He

atin

g

Technical Data

Operating voltage 120 - 240V AC/DC* (min. 110V, max. 265V)Heating element PTC resistor - temperature limitingSurface temperature < 85°C (185°F) (according to VDE 0100),

except upper protective grilleConnection 2-pole terminal 2.5mm², torque 0.8Nm max.Casing plastic according to UL94 V-0, blackDimensions 98 x 38 x 75mmMounting clip for 35mm DIN rail, EN 60715Fitting position vertical airflow (air outlet up, connection on bottom)Operating/Storage temperature -45°C to +70°C (-49°F to +158°F)Operating/Storage humidity max. 90 % RH (non-condensing)Protection type/Protection class IP20 / II (double insulated)Approvals VDE + UL File No. E150057 (according to UL 499, intended

for the use within an enclosure in accordance with UL 508A)Note other voltages on request

Art. No. Heatingcapacity*

Inrush current max. Pre-fuseT (time-delay)

Weight (approx.)

06040.0-00 10W 1.0A 1A 0.2kg06030.0-00 20W 2.5A 2A 0.3kg

*Operating with voltages below 140V AC/DC reduces heating performance by approx. 10%.

* at 20°C (68°F) ambient temperature

Example of connection

Thermostat FTO 011(contact breaker, normally closed)

Heater CSK 060

4

Semiconductor Heater HG 140 Series 15W to 150W

These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature may not fall below a minimum value. The aluminium profile heater body design has a chimney effect and distributes the heat evenly. The heaters are designed for permanent operation. Pressure clamp connectors save time and simplify installation.

Heat

ing

Technical Data

Art. No. Heating capacity* Inrush current max. Pre-fuse T (time-delay) Length (L) Weight (approx.)14000.0-00 15W 1.5A 1A 65mm 0.3kg14001.0-00 30W 3.0A 2.5A 65mm 0.3kg14003.0-00 45W 3.5A 2.5A 65mm 0.3kg

14005.0-00 60W 2.5A 2.5A 140mm 0.4kg

14006.0-00 75W 4.0A 4A 140mm 0.5kg

14007.0-00 100W 4.5A 4A 140mm 0.5kg

14008.0-00 150W 9.0A 6.3A 220mm 0.7kg

*Operating with voltages below 140V AC/DC reduces heating performance by approx. 10%.

*at 20°C (68°F) ambient temperature

Pressure clamp connectorsDynamic heating upWide voltage rangeEnergy savingClip fixingQuick installation

Operating voltage 120-240V AC/DC* (min. 110V, max. 265V)Heating element PTC resistor, temperature limitingHeater body extruded aluminium profile, anodisedConnection 3 pressure clamps for stranded wire 0.5-1.5mm² (with wire

end ferrule) and rigid wire 0.5-2.5mm²Connection casing plastic according to UL94 V-0, blackMounting clip for 35mm DIN rail, EN 60715Fitting position vertical airflow (air outlet up, connection on bottom)Operating/Storage temperature -45 to +70°C (-49 to +158°F)Operating/Storage humidity max. 90 % RH (non-condensing)Protection type/Protection class IP20 / I (earthed)Approvals VDE + UL File No. E150057Accessories screw fixing, Art. No. 09024.0-00 (1 packing unit = 2 pieces)

5

Hazardous area Heater CREx 020 Series 50W, 100W

Heat

ing

Large convection surfaceClip fixingReady for useMaintenance free

Compact convection heater for use in areas with explosion hazard for preven-tion of formation of condensation, temperature fluctuations and for protection against frost in transmitter housings, switch cabinets and measuring equipment.

Technical Data

Explosion protection acc. EN LCIE (Laboratoire Central des Industries Electriques)Conformity certificate 01 ATEX 6073/03, LCIE N° 06 ATEX Q8011, IECEx LCI 07. 0020Heating element high performance cartridgeHeater body aluminium profile, black anodisedConnection Si HF-JZ 3 x 0.75mm² cable, length 1mConnection PE 4mm²Mounting clip for 35mm DIN rail, EN 60715Fitting position vertical airflow (connection on bottom)Operating/Storage temperature -40 to +40°C (-40 to +104°F) / -45 to +70°C (-49 to +158°F)Protection type/Protection class IP65 / I (earthed)

Clip can alternativelybe fixed on long side

Hazardous area Thermostat REx 011see page 14

Art. No. Operating voltage

Heating capacity*

Pre-fuse T (time-delay)

Ex protection type Surfacetempera-

ture

Length (L)

Weight (approx.)

02010.0-00 230-240VAC 50W 0.5A d IIC T5 -Ex tD A21 IP6X T100°C 100°C 150mm 1.3kg

02011.0-00 230-240VAC 100W 1A d IIC T4 -Ex tD A21 IP6X T135°C 135°C 180mm 1.5kg02010.0-01 110-120VAC 50W 0.5A d IIC T5 -Ex tD A21 IP6X T100°C 100°C 150mm 1.3kg

02011.0-01 110-120VAC 100W 1.25A d IIC T4 -Ex tD A21 IP6X T135°C 135°C 180mm 1.5kg

6

Touch-Safe Heater CS 060 Series 50W to 150W(semiconductor)

Low surface temperatureQuick mounting due to clip fixingDouble insulated (plastic)Wide voltage rangeSmall size

Touch-safe heater for the use in enclosures with electrical/electronical compo-nents. The design of the heater supports the natural convection which results in a high air-current of warm air. The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design. Our complete range of thermostats and hygrostats can directly be connected to the heater CS 060. This heater is also available in a version with plug-in thermostat requiring no additional wiring (CSF 060). The heaters are designed for perma-nent operation.

Heat

ing

Technical Data

Art. No. Heating capacity1)

Inrush current max.

Pre-fuse T (time-delay)

Air outlet tem-perature2)

Dimensions Weight (approx.)

06000.0-00 50W 2.5A 4A +86°C (186.8°F) 110 x 60 x 90mm 0.3kg06010.0-00 100W 4.5A 8A +120°C (248°F) 110 x 60 x 90mm 0.3kg06020.0-00 150W 8A 8A +145°C (293°F) 150 x 60 x 90mm 0.5kg

*Operating with voltages below 140V AC/DC reduces heating performance by approx. 10%.

1) Ambient temperature - see Heating capacity / Ambient temperature diagram; 2) measured 50mm above protective grille;

Operating voltage 120-240V AC/DC* (min. 110V, max. 265V)Heating element PTC resistor - temperature limitingSurface temperature < 80°C (176°F), except upper protective grilleConnection 4-pole terminal 2,5mm², torque 0.8Nm max.Casing plastic according to UL94 V-0, blackMounting clip for 35mm DIN rail, EN 60715Fitting position vertical airflow (air outlet up, connection on bottom)Operating / Storage temperature -45 to +70°C (-49 to +158°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type / Protection class IP20 / II (double insulated)Approvals VDE + UL File No. E150057 (according to UL 499, intended for

the use within an enclosure in accordance with UL 508A)Note other voltages on request

Heater CS 060 Heater CS 060

ThermostatFTO 011

Heater CS 060Thermostat

FTO 011

AC

AC

Example of connection

50

0

200

150

100

Heizleistun

g(W

)

-40 -20 0

Leistungs-Umgebungstemperatur-DiagrammCS 160

20 40

178

160

147

132

119122

110102

9385

6661 55

5044

150W

100W

50W

Heating capacity / Ambient temperature diagram CS 060

Temperature(°C)

Heat

ing

capa

city (

W)

7

Touch-Safe Heater CSF 060 Series 50W to 150W(semiconductor)

Heat

ing

Touch-safe heater for the use in enclosures with electrical/electronical compo-nents. The design of the heater supports the natural convection which results in a high air-current of warm air. The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design. This model with plug-in thermostat does not require additional wiring. The heaters are designed for permanent operation. This heater is also available in a version without thermostat (CS 060).

Technical Data

Art. No. Heating capacity1)

Inrushcurrent max

Pre-fuse T (time-delay)

Air outlet tem-perature2)

Switch-off temperature 3)

Switch-ontemperature 3)

Dimensions Weight (approx.)

06001.0-00 50W 2.5A 4A +86°C (186.8°F) +15°C (59°F) +5°C (41°F) 110 x 60 x 90mm 0.3kg06002.0-00 50W 2.5A 4A +86°C (186.8°F) +25°C (77°F) +15°C (59°F) 110 x 60 x 90mm 0.3kg06011.0-00 100W 4.5A 8A +120°C (248°F) +15°C (59°F) +5°C (41°F) 110 x 60 x 90mm 0.3kg06012.0-00 100W 4.5A 8A +120°C (248°F) +25°C (77°F) +15°C (59°F) 110 x 60 x 90mm 0.3kg

06021.0-00 150W 8A 8A +145°C (293°F) +15°C (59°F) +5°C (41°F) 150 x 60 x 90mm 0.5kg

06022.0-00 150W 8A 8A +145°C (293°F) +25°C (77°F) +15°C (59°F) 150 x 60 x 90mm 0.5kg

Operating voltage 120-240VAC* (min. 110V, max. 265V)Heating element PTC resistor - temperature limitingSurface temperature < 80°C (176°F), except upper protective grilleConnection 2-pole terminal 2,5mm², torque 0.8Nm max.Casing plastic according to UL94 V-0, blackMounting clip for 35mm DIN rail, EN 60715Fitting position vertical airflow (air outlet up, connection on bottom)Operating/Storage temperature -40 to +70°C (-40 to +158°F) / -45 to +70°C (-49 to +158°F)Operating/Storage humidity max. 90 % RH (non-condensing)Protection type/Protection class IP20 / II (double insulated)Approvals VDENote other voltages on request

Low surface temperatureIntegrated thermostatQuick mounting due to clip fixingDouble insulated (plastic)Wide voltage rangeSmall size

90

23L

60

Heater CSF 060

Example of connection

50

0

200

150

100

-40 -20 0

Leistungs-Umgebungstemperatur-DiagrammCS 160

20 40

178

160

147

132

119122

110102

9385

6661 55

5044

150W

100W

50W

Heating capacity / Ambient temperature diagram CSF 060

Temperature(°C)

Heat

ing

capa

city (

W)

1) Ambient temperature - see Heating capacity / Ambient temperature diagram; 2) measured 50mm above protective grille;3) tolerance of ± 5K;

*Operating with voltages below 140VAC reduces heating performance by approx. 10%.

8

Compact semiconductor Fan Heater CS 028/CSL028 150W to 400W

Small, compact designQuiet in operationDynamic heating upClip or screw fixing

Fan heater prevents formation of condensation and provides an evenly distributed interior air temperature in enclosures with electric/electronic components. The heater is connected using the internal terminal connectors The small size of the CS 028/CSL 028 makes it ideal for use in enclosures where space is at a premium.

Heat

ing

Technical Data

Heating element PTC heating elementSurface temperature 150W/250W: max. 50°C (122°F), except upper protective

400W: max. 65°C (149°F), except upper protective grilleat 20°C (68°F) ambient temperature

Axial fan, ball bearing air flow, free flow:CS 028: 13.8m³/hCSL 028: 45m³/h (230VAC), 54m³/h (120VAC)service life 40,000h at 40°C (104°F)

Connection 2-pole clamp max. 2.5mm² (CSL 028 with strain relief),clamping screw torque 0.8Nm max.

Casing plastic according to UL94-0, blackMounting clip for 35 mm DIN rail, EN 60715 or screw fixing (Ø 5.3mm)Fitting position vertical airflow (air outlet up)Operating / Storage temperature -45 to +70°C (-49 to +158°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type / Protection class IP20 / II (double insulated)Approvals UL File No. E150057 (according to UL 499, intended for the

the use within an enclosure in accordance with UL 508A)230V only: VDE

Note other voltages on request

Heating capacity / Ambient temperature diagram CS 028 / CSL 028

Temperature(°C)

Heat

ing

capa

city (

W)

Photo: Fan Heater CSL 028

W

H

D

Screw fixing Clip fixing

Fan Heater CS(L) 028Thermostat FTO 011(contact breaker, normally closed)

Example of connection

View: back side

Art. No.Clip fixing

Art. No.Screw fixing

Series Operatingvoltage

Heatingcapacity*

Inrush current max.

Pre-fuseT (time-delay)

Dimensions Weight (approx.)

02800.0-00 02800.0-01 CS 028 230VAC, 50/60Hz 150W 12A 6.3A 75 x 65 x 90 mm 0.3kg02811.0-00 02811.0-01 CSL 028 230VAC, 50/60Hz 250W 9A 6.3A 90 x 85 x 111 mm 0.5kg02810.0-00 02810.0-01 CSL 028 230VAC, 50/60Hz 400W 15A 10A 90 x 85 x 111 mm 0.5kg02800.9-00 02800.9-01 CS 028 120VAC, 50/60Hz 150W 6A 6.3A 75 x 65 x 90 mm 0.3kg

02811.9-00 02811.9-01 CSL 028 120VAC, 50/60Hz 250W 6A 6.3A 90 x 85 x 111 mm 0.5kg

02810.9-00 02810.9-01 CSL 028 120VAC, 50/60Hz 400W 9A 9A 90 x 85 x 111 mm 0.5kg

*at 20°C (68°F) ambient temperature;

9

Compact Fan Heater Series HGL046 250W,400W

Heat

ing Compact fan heater prevents formation of condensation. The integrated high

performance axial fan provides forced air circulation and so guarantees an even temperature in enclosures.

Compact DesignClip fixingLong service lifeMaintenance freeTemperature safety cut-out

View from below

SwitchModuleSM 010

Control contact,e.g. Temperatureregulator KTO 011

Control contact,e.g. Temperatureregulator KTO 011

HeaterFan Heater HGL 046 (AC 230V and 120V) with temperature safety cut-out

HeaterFan Heater HGL 046(DC 24V and 48V) with temperature safety cut-out

Art. No. Operating voltage Heating capacity

Pre-fuse T (time-delay)

Length (L)

Weight (approx.)

Approvals

04640.0-00 230VAC, 50/60Hz 250W 2A 182mm 1.1kg VDE + UL File No. E15005704641.0-00 230VAC, 50/60Hz 400W 4A 222mm 1.4kg VDE + UL File No. E15005704640.9-00 120VAC, 50/60Hz 250W 4A 182mm 1.1kg VDE + UL File No. E15005704641.9-00 120VAC, 50/60Hz 400W 5A 222mm 1.4kg VDE + UL File No. E150057

04640.1-00 24VDC 250W 16A 182mm 1.1kg -

04640.2-00 48VDC 250W 8A 182mm 1.1kg -

04641.2-00 48VDC 400W 12,5A 222mm 1.4kg -

Technical DataHeating element resistance heaterTemperature safety cut-out to protect against overheating in case of fan failure,

automatic resetHeater body anodised extruded aluminium profileSurface temperature max. 75°C (400W)Axial fan, ball bearing Airflow, free flow

AC: 45m³/h (50Hz) or 54m³/h (60Hz)DC: 54m³/hservice life 50,000h at 25°C (77°F)

Connection internal connection terminal 1.5mm² with strain relief,clamping torque 0.8Nm max.

Connection casing plastic according to UL94 V-0, blackMounting clip for 35mm DIN rail, EN 60715Fitting position vertical airflow (air outlet up)Operating / Storage temperature -45 to +70°C (-49 to +158°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type / Protection class IP20 / I (earthed)Note: In the case of 24VDC and 48VDC the fan heater has to be switched via a relay. For this purpose we recommend our electronic relay SM 010 (Art. No. 01000.0-00 and 01001.0-00).

10

Roof Filter Fan RFP 018 Series 300m³/h, 500m³/h

Roof filter fans find use in enclosures and housings, from which warm air has to be diverted to lower the internal temperature. These low-noise roof filter fans are used to expel warm air from within the enclosure which has been generated by the stray power of the components and so protects the internal devices from overheating. To exchange the filter mat the hood can be easily opened without tools. The roof exit filter provides passive ventilation.

Vent

ilatin

gEnclosure cut-out

Hole

cen

ters

Photo: Art. No. 01860.0-00

Very low noiseMinimal depth in enclosureHigh through-flow air volumeHigh reliabilityTime-saving installation and mat exchange

Photo: Art. No. 01861.0-00

Roof Filter Fan (01860.0-xx)

Roof Filter Fan (01861.0-xx)

Technical Data

Axial fans, ball bearing service life 50,000h at 25°C/77°F (65% RH)fan body aluminium, rotor plastic

Connection 3-pole clamp for 2.5mm², clamping torque 0.8Nm max.Case plastic according to UL94 V-0, light grey;

weather proof and UV light resistant according UL746C (f1)Filter mat G3 acc. to DIN EN 779, filtering degree 85%Filter material synthetic fibre with progressive construction, temperature

resistant to 100°C, self-extinguishing class F1;moisture resistant to 100% RH, reusable - cleaning bywashing or vacuuming

Operating / Storage humidity max. 90 % RH (non-condensing)Prot. type / Protection class IP32 / I (earthed)Approvals UL intended; (230V only: VDE

Important note: For reasons of pressure compensation the roof filter fan must always be operated incombination with a passive intake filter (e.g. Art. No. 11803.0-00) or another filter fan (e.g. Art. No. 01803.0-00).

Roof Filter Fan RFP 018 Series

Art. No. Depth in enclosure Enclosure cut-out Weight (approx.) Filter mat Protection type11860.0-00 11mm 250 x 250mm + 0.4 1.0kg G3 acc. to DIN EN 779, filtering degree 85% IP32

Roof Exit Filter REP 118 Series

Filter mat 282 x 282mmG3 (1 packing unit = 3 pcs.) Art. No. 08613.0-01

Filter Mat FM 086

Art. No. Operatingvoltage

Air volume,free flow

Currentconsump-

tion

Average noise level

(DIN EN ISO 4871)

Depth inenclo-sure

Enclosurecut-out

Weight(approx.)

Operating /Storage temperature

01860.0-00 230VAC, 50Hz 300m³/h 68W 55dB (A) 52mm 250 x 250mm + 0.4 3.3kg -10 to +70°C (+14 to +158°F) / -40 to +70°C (-40 to +158°F)01861.0-00 230VAC, 50Hz 500m³/h 64W 67dB (A) 107mm 250 x 250mm + 0.4 2.6kg -25 to +70°C (-13 to +158°F)01860.0-02 120VAC, 60Hz 345m³/h 60W 55dB (A) 52mm 250 x 250mm + 0.4 3.3kg -10 to +70°C (+14 to +158°F) / -40 to +70°C (-40 to +158°F)01861.0-02 120VAC, 60Hz 575m³/h 85W 67dB (A) 107mm 250 x 250mm + 0.4 2.6kg -25 to +70°C (-13 to +158°F)

11

Small, compact Thermostat KTO 011 / KTS 011

Regu

latin

g KTO 011: Thermostat (normally closed); contact breaker for regulating heaters.KTS 011: Thermostat (normally open); contact maker for regulating of filter fans and heat exchangers or for switching signal devised when temperature limit has been exceeded.

Large setting rangeSmall sizeSimple to mountHigh switching performance

Technical DataSwitch temperature difference 7K (± 4K tolerance)Sensor element thermostatic bimetalContact type snap-action contactService life > 100,000 cyclesMax. Switching capacity 250VAC, 10 (2) A 120VAC, 15 (2) A

DC 30WConnection 2-pole terminal, clamping torque 0.5Nm max.:

rigid wire 2.5mm²stranded wire (with wire end ferrule) 1.5mm²

Mounting clip for 35mm DIN rail, EN60715(or for exit filter EF 118 Series)

Casing plastic according to UL94 V-0, light grey Dimensions 60 x 33 x 43mmWeight approx. 40gFitting position variableOperating / Storage temperature -45 to +80°C (-49 to +176°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type IP20

Connection diagrams

Heater

ThermostatKTO 011 (NC)

ThermostatKTS 011 (NO)

Filter fan,Cooling equipment,Signal device

ThermostatKTO 011 (NC)

Heater ThermostatKTS 011 (NO)

e.g. Fan e.g. Signaldevice

ThermostatKTS 011 (NO)

Examples of connection

Setting range Art. No. Contact Breaker (NC) Art. No. Contact Maker (NO) Approvals0 to +60° 01140.0-00 01141.0-00 VDE

-10 to +50°C 01142.0-00 01143.0-00 VDE + UL File No. E164102+20 to +80°C 01159.0-00 01158.0-00 VDE + UL File No. E164102+32 to +140°F 01140.9-00 01141.9-00 VDE + UL File No. E164102

+14 to +122°F 01142.9-00 01143.9-00 VDE + UL File No. E164102

0 to +60°C 01146.9-00 01147.9-00 VDE + UL File No. E164102

12

Tamperproof Thermostats (Pre-set) FTO 011 / FTS 011

Small sizeDefault temperature settingsEasy to installHigh switching tolerance

Tamperproof (Pre-set) Thermostat FTO 011Contact breaker / NC (red casing) for regulating heaters or for switching signal devices when temperature has fallen below the minimum value. The contact opens when temperature is rising.Tamperproof (Pre-set) Thermostat FTS 011Contact maker / NO (blue casing) for regulating filter fans, heat exchangers, cooling devices or for switching signal deviceswhen temperature limit has been exceeded. The contact closeswhen temperature is rising.

Regu

latin

g

Technical Data

Sensor element thermostatic bimetalContact type snap-action contactService life > 100,000 cyclesMax. switching capacity 250V AC, 5 (1.6)A

120V AC, 10 (2)ADC 30W

Max. inrush current AC 10AConnection 2-pole terminal for 2.5mm², torque 0.8Nm max.Mounting clip for 35mm DIN rail, EN 60715Casing plastic according to UL94 V-0, light greyDimensions 47 x 33 x 33mmWeight approx. 30gFitting position variableOperating / Storage tempera- -40 to +80°C (-40 to +176°F) / -45 to +80°C (-49 to +176°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type IP20Approvals VDE + UL File No. E164102

Art. No. Contact Switch-off temperature Switch-on temperature01160.0-00 Contact breaker (NC) +15°C / +59°F (± 5K tolerance) +5°C / +41°F (± 5K tolerance)01160.0-01 Contact breaker (NC) +25°C / +77°F (± 5K tolerance) +15°C / +59°F (± 5K tolerance)

Switch-on temperature Switch-off temperature01161.0-00 Contact maker (NO) +50°C / +122°F (± 6K tolerance) +40°C / +104°F (± 7K tolerance)

01161.0-01 Contact maker (NO) +60°C / +140°F (± 6K tolerance) +50°C / +122°F (± 7K tolerance)

01161.0-02 Contact maker (NO) +35°C / +95°F (± 6K tolerance) +25°C / +77°F (± 7K tolerance)

ThermostatFTO 011

Heater Filter fanSignaldeviceThermostat

FTS 011Thermostat

FTS 011

Examples of connection

13

Dual Thermostat ZR 011

Regu

latin

g

Two thermostats in one casing:Thermostat (contact breaker, normally closed) for regulating heaters.Thermostat (contact maker, normally open) for regulating filter fans and heat exchangers or switching signal devices when temperature limit has been ex-ceeded.Heaters and cooling equipment can be switched independently from each other with a temperature offset as opposed to the usual change-over contacts.

NO and NC in one casingSeparate adjustable temperaturesHigh switching capacityTerminals easily accessibleClip fixing

Art. No. Setting Range Setting Range01172.0-00 contact breaker, normally closed 0 to +60°C contact maker, normally open 0 to +60°C01172.0-01 contact breaker, normally closed +32 to +140°F contact maker, normally open +32 to +140°F01175.0-00 contact breaker, normally closed -10 to +50°C contact maker, normally open +20 to +80°C01175.0-01 contact breaker, normally closed +14 to +122°F contact maker, normally open +68 to +176°F

01176.0-00* contact maker, normally open 0 to +60°C contact maker, normally open 0 to +60°C

01176.0-01* contact maker, normally open +32 to +140°F contact maker, normally open +32 to +140°F

Technical DataSwitch temperature difference 7K (± 4K tolerance)Sensor element thermostatic bimetalContact type snap-action contactService life > 100,000 cyclesMax. Switching capacity 250VAC, 10 (2) A

120VAC, 15 (2) ADC 30W

Connection 4-pole terminal, clamping torque 0.5Nm max.:rigid wire 2.5mm²stranded wire (with wire end ferrule) 1.5mm²

Mounting clip for 35mm DIN rail, EN60715Casing plastic according to UL94 V-0, light greyDimensions 67 x 50 x 46mmWeight approx. 90gFitting position variableOperating / Storage tempera- -45 to +80°C (-49 to +176°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type IP20Approvals VDE + UL File No. E164102

Connection diagrams

Heater

Filter fan, Cooling equipment, Signal device

ThermostatZR 011 (NC/NO)

* For regulating heat exchangers and fans (e.g. LE 019) and as an alarm contact for monitoring the interior temperature of electronic enclosures.

14

Hazardous area Thermostat REx 011 Series 15°C, 25°C

Compact designSet temperatureHigh switching capacity

Compact small mechanical thermostat for temperature regulation and monitor-ing of heaters, for example in transmitter cabinets, control panels and measuring equipment which are deployed in areas with explosion hazard. The special switch construction enables high response accuracy, small switch temperature difference and a very long service life. High switching performance allows direct control of the heaters.

Regu

latin

g

Technical Data

Explosion proof according to EN LCIE (Laboratoire Central des Industries Electriques)Conformity certificate 01 ATEX 6074/02, LCIE N° 06 ATEX Q8011, IECEx LCI 07. 0021Sensor element thermostatic bimetalContact type (1-pole) opens with rising temperatureService life > 100,000 cyclesMax. Switching capacity 250VAC, 4 (1) AConnection Si HF - JZ 3 x 0.75mm², length 1mMounting mounting bracket with nut M8 (see illustration)Casing aluminium, black anodisedDimensions length 110mmWeight approx. 0.2kgFitting position variableOperating / Storage temperature -40 to +40°C (-40 to +104°F) / -45 to +70°C (-49 to +158°F)Protection type / Protection class IP65 / I (earthed)

AluminiumMounting Bracket

Art. No. Ex protection type Switch-off temperature Switch temperature difference01180.0-00 d IIC T6 - Ex tD A21 IP6X T85°C +15°C / +59°F (± 5K tolerance) 4K (± 1K tolerance)01181.0-00 d IIC T6 - Ex tD A21 IP6X T85°C +25°C / +77°F (± 5K tolerance) 4K (± 1K tolerance)

15

Lamp Series LED 025

Ligh

ting

The lamp series LED 025 is suitable for all types of panels and enclosures, especially where space is at a premium. The lamps have a very long service life thanks to the use of LED technology. They are available with powerful non-slip rubberized magnets allowing them to be quickly positioned in any steel enclosure. Alternatively they can be fixed me-chanically. The power output allows up to 10 lamps to be connected to each other (daisy chain). Both the power input and output connectors snap lock into their sockets. With the integrated power unit and the plugs the lamp can quickly be connected.

Art. No. Magnet fixing Art. No. Screw fixing Operating voltage Switch Weight (approx.)02540.0-00 02540.0-01 100-240VAC, 50/60Hz (min. 90VAC, max. 265VAC) on/off light switch 0.2kg02540.1-00 02540.1-01 24-48VDC (min. 20VDC, max. 60VDC) on/off light switch 0.2kg

Technical DataPower consumption max. 5WLuminosity 290Lm at 120° (870Lm at 360° or equivalent 75W light bulb)Lamp type LED, angle of radiation 120°

light color: daylight, color temperature: 6,500KService life 60,000h at 20°C (68°F)Connection 2-pole connector with snap lock

AC: max. 2.5A / 240VAC, color: whiteDC: max. 2.5A / 60VDC, color: blue

Mounting magnet fixing orscrew fixing, M5, 250mm centers

Casing plastic, transparentDimensions 351 x 34 x 32mm (with magnet fixing)

351 x 36 x 32mm (with screw fixing)Operating / Storage temperature -30 to +60°C (-22 to +140°F) / -40 to +85°C (-40 to +185°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type / Protection class IP20 / II (double insulated)Approvals VDE + UL intendedProtection type IP20Approvals VDE + UL File No. E164102

Photo 1: Lamp LED 025 with magnet fixing

Photo 2: Lamp LED 025 with screw fixing

* approx. 5min. fixed switch-on duration

Wide voltage rangeIntegrated power unitDaisy chainLong-lived, maintenance-freeMagnet or screw fixingEnergy-saving by LED technologyQuick connection

Photo 1

Photo 2

Side viewmagnet fixing

Side viewscrew fixing

Important note: Connectors and cables for electrical connection are not included in the delivery. These partsneed to be ordered separately, see Accessories on next page.

16

Lamp series LED 025 - Accessories

Ligh

ting

Connection cable with female connector and open end

Extension cable with 2 connectors for daisy chain connection

1

Photo: Extension cable, Art. No. 244358

2

Female / Male connectors

Art. No. Model Voltage type Color Use for Approvals264057 female connector AC white power input VDE + UL264058 male connector AC white power output VDE + UL264059 female connector DC blue power input VDE + UL264060 male connector DC blue power output VDE + UL

Art. No. Model Length Voltage type

Color Use for Approvals

244356 connection cable 2x1.5mm² with female connector 2.0m AC connector: white; cable: white power input VDE244357 connection cable 2xAWG 16 with female connector 2.0m AC connector: white; cable: white power input VDE + UL244360 connection cable 2x1.5mm² with female connector 2.0m DC connector: blue; cable: white power input VDE244361 connection cable 2xAWG 16 with female connector 2.0m DC connector: blue; cable: white power input VDE + UL

Art. No. Model Length Voltage type

Color Use for Approvals

244358 extension cable 2x1.5mm² with 2 connectors 1.0m AC connector: white; cable: white daisy chain VDE244359 extension cable 2xAWG 16 with 2 connectors 1.0m AC connector: white; cable: white daisy chain VDE + UL244362 extension cable 2x1.5mm² with 2 connectors 1.0m DC connector: blue; cable: white daisy chain VDE244363 extension cable 2xAWG 16 with 2 connectors 1.0m DC connector: blue; cable: white daisy chain VDE + UL

1 2 2

Connection Example

Photo: Connection cable, Art. No. 244356

Photo: Female connector, Art. No. 264057 Photo: Male connector, Art. No. 264058

This illustration shows the LED 025 lamp in a daisy chain application. The lamps are conveniently connected via quick connection plugs – up to 10 lamps max. can be daisy-chained this way. The snap lock connectors ensure a stable electrical connection even if subjected to heavy vibration. The connection example shows a 230VAC application, using the following cables: connection cable with female connector, Art. No. 244356 (1); daisy chain extension cable with 2 connectors, Art. No. 244358 (2).

Female/Male connectors are also available to assemble cables in non-standard lengths.

17

Electrical Socket SD 035 Series

Ligh

ting

Quickly connectedAvailable with or without fuseClip fixing

The DIN rail mounted electrical socket can be quickly fitted and connected in enclosures allowing the use of auxiliary products such as hand lamps, measur-ing devices, soldering irons etc. The unit is available with and without fuse and in many world socket standards.

Art. No. Operating Voltage max. Socket Model Nominal Current Approvals03500.0-00 250VAC Germany/Russia (1) with fuse* 6.3A -

03500.0-01 250VAC Germany/Russia (1) without fuse 16.0A -03501.0-00 250VAC F/PL/CZ/SK (2) with fuse* 6.3A -

03501.0-01 250VAC F/PL/CZ/SK (2) without fuse 16.0A -

03502.0-00 250VAC Switzerland (3) with fuse* 6.3A -

03502.0-01 250VAC Switzerland (3) without fuse 10.0A -

03503.0-00 250VAC UK/Ireland (4) with fuse* 6.3A -

03503.0-01 250VAC UK/Ireland (4) without fuse 13.0A -

03504.0-00 125VAC USA/Canada (5) with fuse* 6.3A UL File No. E222026

03504.0-01 125VAC USA/Canada (5) without fuse 15.0A UL File No. E222026

03505.0-00 250VAC Italy (6) with fuse* 6.3A -

03505.0-01 250VAC Italy (6) without fuse 16.0A -

Technical Data

Connection 3 x pressure clamps for stranded and rigid wire 0.5 - 2.5mm²Mounting clip for 35mm DIN rail, EN60715Casing plastic according to UL94 V-0, light greyDimensions 92 x 62 x 48mmWeight approx. 0.2kgFitting position variableOperating / Storage temperature -45 to +70°C (-49 to +158°F)Operating / Storage humidity max. 90 % RH (non-condensing)Protection type / Protection class IP20 / I (earthed)

Connections from mains

*fuse Ø 5 x 20mm

18

Stego_leaflet_en_0511

© STEGO Elektrotechnik GmbH 08/2010

Samaratel. +7 846 273 95 85samara@klinkmann.spb.ru

Yekaterinburgtel. +7 343 376 5393yekaterinburg@klinkmann.spb.ru

St. Petersburgtel. +7 812 327 3752klinkmann@klinkmann.spb.ru

Moscowtel. +7 495 641 1616moscow@klinkmann.spb.ru

Helsinkitel. +358 9 540 4940automation@klinkmann.fi

Vilniustel. +370 5 215 1646post@klinkmann.lt

Rigatel. +371 6738 1617klinkmann@klinkmann.lv

Мinsktel. +375 17 200 0876minsk@klinkmann.com

Tallinntel. +372 668 4500klinkmann.est@klinkmann.ee

Кievtel. +38 044 495 33 40klinkmann@klinkmann.kiev.ua

www.klinkmann.com