Sound for Underground Dance - The Technical Foundation.

7/29/2019 Sound for Underground Dance - The Technical Foundation.

1/20

BASSBOT AUDIO GALLERIES EVENTS FORUMS NETWORK

Bassbot.org

Search this site:

skroller

My account Create content Recent posts Feed aggregator Log out

Syndicate

Sound for underground Dance : The technical

foundation.

View Track

February 15, 2009 -- Posted by: emperor in

Bass Culture

This document explains in simple terms how to design, configure, and operate soundsystems for the optimal reproduction of "underground" dance music. By following theseprinciples and guidelines, you will be able to insure that a sound system sounds as

good as it possibly can, emphasizing the most important elements of dance music,while being clean, precise, and free of significant distortion. By designing and operatinga sound system as suggested here, it will truly be high-fidelity, will not cause hearingdamage, and will contribute greatly to the long term success of any sound provider,club, promoter, party crew, etc.

Introduction
http://bassbot.org/bassbothttp://bassbot.org/bassmassifhttp://bassbot.org/imagehttp://bassbot.org/eventhttp://bassbot.org/forumhttp://bassbot.org/weblinkshttp://bassbot.org/http://bassbot.org/user/25http://bassbot.org/node/addhttp://bassbot.org/trackerhttp://bassbot.org/aggregatorhttp://bassbot.org/logouthttp://bassbot.org/node/3403http://bassbot.org/node/3403/trackhttp://bassbot.org/user/emperorhttp://bassbot.org/forums/culture/bass-culturehttp://bassbot.org/forums/culture/bass-culturehttp://bassbot.org/forums/culture/bass-culturehttp://bassbot.org/forums/culture/bass-culturehttp://bassbot.org/user/emperorhttp://bassbot.org/node/3403/trackhttp://bassbot.org/node/3403http://bassbot.org/logouthttp://bassbot.org/logouthttp://bassbot.org/logouthttp://bassbot.org/aggregatorhttp://bassbot.org/aggregatorhttp://bassbot.org/aggregatorhttp://bassbot.org/trackerhttp://bassbot.org/trackerhttp://bassbot.org/trackerhttp://bassbot.org/node/addhttp://bassbot.org/node/addhttp://bassbot.org/node/addhttp://bassbot.org/user/25http://bassbot.org/user/25http://bassbot.org/user/25http://bassbot.org/http://bassbot.org/http://bassbot.org/http://bassbot.org/weblinkshttp://bassbot.org/forumhttp://bassbot.org/eventhttp://bassbot.org/imagehttp://bassbot.org/bassmassifhttp://bassbot.org/bassbot


2/20

Any combination of low-grade speakers and amplifiers are enough to make some noise, but the accuratereproduction of music, with flat frequency and phase response across the entire audible spectrum, at highvolume levels, is a science and art that still has plenty of room for improvement, and that will continueto evolve for centuries to come. Tradeoffs are made by all audio equipment manufacturers betweenaccuracy in frequency and phase response, efficiency, equipment volume and weight, and materials andR&D costs. For many applications, such as a low-cost public address system or guitar amp, 1950's eratechnology works fine. But take a look at the world's largest sound companies and one thing becomesclear, they insist on only the highest possible quality equipment, because they know that their reputationand long term success depend on it.The fundamentals of connecting various pieces of equipment together and operating a sound system arenot covered here, as there are many other reference materials that explain the basics of sound systems.Due to the small size and non-mainstream nature of the underground dance music market however,sound schools, books, and other educational resources do not devote much if any attention to its uniqueneeds. This document illustrates the main design issues for electronic dance music, and makes clearthat its unique characteristics require a different approach to sound system design than is followed formost other music types. With an understanding of the principles covered here, you will be better able toset up a sound system that makes dance music sound as good as it can.

The Real World

It is important to carefully review the motives, experience, and training of anyone you talk to about soundsystems. Hype and marketing are the way most business gets done in consumer markets particularlyin the music world. When seeking out information, keep in mind that most people's opinions are biasedtoward their own financial interests, and/or their own lack of knowledge or experience in a given area.Only those who put the time into seeking out a wide array of information resources can achieve truequality and sophistication.There are many preconceptions that people have which can appear sensible on the surface, but thatare often completely wrong in the context of underground dance music. In reality, most people in themainstream audio world don't know much about the unique requirements of DJ's and of dance music.When you are getting advice from a salesman, sound guy, musician, electronics guru, engineer, friend,family member, etc., remember that setting up the best sound system you can for the money is not asimple thing. The people that know how to do it the best way are those who have been doing it for manyyears.

Some readers may wonder, "Why is anything a DJ knows important in setting up a sound system? Theyjust play records..." Well, if your intention is to do a club or provide sound in such a way as to have a bitof genuine class and sophistication in what you do, and in the clientele you attract, you must ensure thatgood DJs like to play on your sound system. The "average" DJ may not particularly care how easy yoursystem is to play on, but DJs who are exceptionally good, and who have been around awhile, do care. Ifyou are running a club, lounge, sound system, etc. and have any artistic integrity, you are well aware thatkeeping your DJs, performers, and staff happy can be just as important as keeping the audience happy.Most non-DJs do not know that some systems are much easier and more enjoyable to play on thanothers, and being a top DJ is not as easy as it looks. It takes talent, years of experience, and tremendousfocus to mix records perfectly on numerous different sound systems, each of which often have variousissues such as excessive turntable feedback, needles that skip from being bumped by dancers or fromfloor vibrations, booth monitor systems with output levels that are too low, too high, nonadjustable, orhalfway blown-out, large sound delays resulting from speakers placed too far away or from echoes off of

overly reflective surfaces, lost dynamic range and responsiveness due to over-compression, and variousother issues that make it more difficult to play the best set a DJ can. If your system is designed to preventthese sorts of issues, DJs will like playing on it, the music will be better overall, and you will be that muchmore likely to be successful.

As with most other things in the world, a club or event is only as good as its weakest link. The club/event markets in most cities are highly competitive, and if you want to be successful you can't have anyweak links. In the underground dance music market this means you need to have a comfortable venue,very good sound and DJs, friendly and unobtrusive staff, bartenders, security, doorpersons, etc., cleanbathrooms for the ladies, reasonable cover charges, interesting and fresh decor and layout, professionallydone promotions and marketing, etc. If all these elements are done properly, your success is almost


3/20

assured. If any of them are missing or not right, you risk your entire investment.If you design your sound system as is suggested in the remainder of this document, it will indeed be "DJfriendly", and will be more likely to sound as good as it should. Many venue owners and promoters takeit for granted, but a quality sound system is one of the most important ingredients in the success of clubsand events. A top quality sound system is also a great marketing tool, that can be a key differentiatorbetween you and your competition, and that helps make clear to your market that you don't compromisewhen it comes to quality. We have seen many 100's of clubs, club nights, and sound systems come andgo in the past 15 years. If you're not willing to put everything you can into it, to make it something reallyoutstanding and exceptional, that will stand the test of time, then why waste your time?It can take a lot of research, time, and travel to design the best possible system for your budget and yourapplication. Even if you are fortunate enough to find an educated, talented sound specialist, he or sheis likely not a DJ, or has not worked with dance music sound systems enough to fully understand thedifferences.

The Characteristics of Dance Music

Dance music has substantially different characteristics than many other types of music, and requires adifferent approach to designing and setting up medium to large scale sound systems. A comparison ofseveral music types that illustrates some of these differences is as follows:

music type underground dance rock & roll classical

primary elements percussion, bass, subbass guitar, percussion,vocals

string and pipeinstruments

optimal systemfrequencyresponse

subbass response should begreater in level than any otherfrequency range. -3dB cutofffrequency should be below 30Hzat max. SPL

varies flat

desired SPL bass and subbass SPL shouldbe very high, but mids and highsshould not be uncomfortably loud

very high generally medium, but dynamicrange must be very high

desired SPLuniformity withinvenue

low to medium medium to high high

These definitions make clearer the elements required to maximize the performance of sound systems fordance music, particularly for the more "underground" (i.e. more sophisticated and innovative) varieties.This section discusses these elements and their overall role in a high-quality sound system, and thefollowing sections address how these elements are best achieved.In the earliest and most primitive incarnations of music, drums and percussion were the first elementsutilized, and thus were the construct and foundation of what became known as "music". The drum circle,probably the oldest form of group music making, still exists today and continues to offer its participants anexperience of harmony, unity, and heightened experience. Examining the root nature of music, and thephysiology of ourselves, it is obvious that dance is the most natural and explicit mechanism for interacting

with music.Perhaps the defining element of "underground" music is its attempt to incorporate these root elements,and its primary dedication to the participant. Underground dance music thus shares with the earliestincarnations of music a foundation of percussion instruments (or their electronic emulation as maybe the case). This is further evidenced by examining the earlier manifestations of present day dancemusic, such as Chicago House in the mid 80's, which was generally characterized by minimal percussiveframeworks. Vocals and melody were important elements, but in general neither were present enough ofthe time to make them as obvious of defining elements as the percussive rhythms.

A natural extension to the connection of dance music to percussion has evolved of its own in the relativelyrecent past: bass and subbass. Again considering the physiological mechanisms dance music directs


4/20

itself towards, and looking at the properties of various sound frequencies, the connection is clear. Assound frequency becomes lower, its oscillation wavelengths become more closely coupled to the physicaldimensions of the body than to the relatively small dimensions of the inner ear. It is for this reasonthat low subbass can be felt as much as heard. Thus, a direct physical interface is available that is anexcellent tool in the arsenal of music producers and DJs. The effectiveness and embracement of bassand subbass is evidenced by the surfacing of entire new genres such as Drum & Bass.In the design and operation of sound systems, it is important to understand the intentions of an eventor club, of the participants, and of those playing the music. One goal of many sound professionalsfrequently is simply to insure that the entire venue is supplied with high volume sound. Frequently,numerous arrays of speakers are deployed in various places in the venue to insure that there is literallynowhere to go where the sound is not loud. For certain events and styles of music, this approach closelymatches the intentions of the producers, attendees, and musicians and/or DJs. Frequently this approachis entirely inappropriate however.The modern rave, as well as many superclubs that attempt to model the idealized rave atmosphere, arein part characterized by a large diversity of available experiences from which the participants can freelychoose. The attractiveness and success of events are often determined in part by the level of varietyand diversity that are present in the musical styles, entertainment, venue geography, visual design, time-space utilization, and in the creativity and innovation and new concepts that are brought forth. From thisit is obvious that the sound system should fit precisely into this milieu such that it is maximally effectivewhere desired, and yet completely absent perhaps from other areas. Well planned events and clubs

often have "chill" areas, or areas with ambient music, to provide quiet and relaxing places, and to addcontrast to the musical landscape of the venue. Some events and clubs may also intentionally positionspeakers such that within areas there are places to go where the sound is quieter, and more conduciveto socializing, communication, dancing, or cooling off. These approaches always leave each participantmore freedom to gravitate to the place that most suits his or her desires.

The Sunsonic Criteria

There are presently 8 Sunsonic Criteria. Some may include more than one element or requirement.Several of these elements and requirements are covered in more detail in later sections.

I. Speaker Cabinet Selection Should Emphasize Bass and Subbass Reproduction.

Dance music has a very important, yet subtle property that its appreciation and effectiveness are notimproved by utilizing high midrange or treble volume levels. In fact, the exact opposite effect oftenoccurs. Overly loud and harsh midrange and treble sound pressure levels cause a temporary reduction inperceived dynamic range in the listener, induce fatigue and stress, and over time cause hearing loss.Of equal importance is the subtle property that subbass does not exhibit these properties to nearly thesame degree. This is because the energy content of a sound is directly proportional to its frequency andamplitude. Subbass frequencies have large displacement amplitudes, but their frequencies are very lowand their wavelengths are very long. As a result they couple more efficiently to the body itself than to thesmall inner dimensions of the ear, which is why you can feel the lowest subbass frequencies as much ormore than you hear them.The first criteria is thus as follows:A. Employ subbass cabinets in a sufficient ratio to full-range cabinets such that the subbass power ratingis at least as high as that of the full-range cabinets.

We highly recommend Cerwin-Vega T-36 and SL-36B bass bins, as these are inexpensive, clean,very reliable, and are compact and loud. Whatever you do though, use only horn-loaded or Helmholtzresonator-loaded subbass cabinet designs. If you have more money to spend, and require moreportability or better space efficiency, look into NEXO or Funktion-One subbass cabinets. Avoid front-loaded bass cabinets, as they have much lower efficiency and as a result just don't put out very muchbass.

As an example, if you have 2 double 15" full-range cabinets that are each rated at 1,500 Watts programpower, you should have as many bass bins as are necessary to put out 1 to 1.5 times that amount ofpower. In this case 4 Cerwin-Vega T-36s would be an ideal match. A more general approach would be


5/20

to figure you'll need one single-18" horn-loaded subbass cabinet per 15" or 18" driver in your full-rangecabinets. That works out to 2 T-36 style cabinets per double 15" full-range cabinet.Note that the optimal ratio of subs to full-range cabinets does vary depending on the venue. Due to bassloading issues, outdoor venues require more bass bins to provide the same subbass SPL as in an indoorvenue. The larger the air volume of a space, the more bass bins you need to produce the same subbassSPL. In addition, in an indoor venue, walls and corners can be used to provide 1/4 or 1/8th space bassloading, which results in far greater subbass efficiency and output level. Outdoor venues do not usuallyhave walls, in which case the bass bins will only be half-space loaded. It takes 4 half-space loaded bassbins to produce the same output SPL as 1 eighth-space (corner) loaded bass bin. This is a subtle butvery important property you must keep in mind when deciding where to put speakers. When doing soundin an indoor venue, if the speakers can be backed up into corners, you will get the most bass output.The second best option is to back them up against a wall. If that is not practical either, for instance ifthey have to be in front of a stage or something and more than 10 or 20 feet from any walls, then you aredefinitely going to need more bass bins than full-range cabinets. If you are fortunate enough to do soundin a small venue shaped like a simple square or rectangle, with nothing between the dancefloor and thewall and corners, you can back the speakers into the corners and you will get plenty of subbass, evenwith only 1 bass bin in each corner. Note that these loading issues apply only to bass and subbass.Higher frequencies have much shorter wavelengths and their levels are not significantly affected byspeaker placement.B. Select full-range cabinets that have extended low-frequency response, and non-harsh midrange and

high-frequency response.We recommend double 15-inch full-range models such as the Carvin TCS215, EV T-252+, EAW LA325,PAS RS-1.2, or the Yorkville E2152. These cabinets are well made and sound very good for what theycost. If you have more money to spend, look into NEXO, Funktion-One, or Meyer cabinets. We stronglydiscourage purchasing full-range cabinets that have only one front-loaded bass driver. If you don't havelarge bass drivers with fairly high cutoff frequencies, your bass will not be well defined or have strongpercussive impact. Also avoid cabinets that crossover the second 15" driver such that it is used formidbass only.Keep your mid and high volume levels as low as possible, so they are clean, crisp, and audible, but notharsh or in-your-face. By having very loud subbass below 65Hz or so, you can then set the mids andhighs fairly quiet, but the system will still sound and feel very loud. The resulting sound however willbe very clear and not at all harsh to the ears, and at the end of the night your ears will have sufferedno damage. In other words, below 65Hz is where you want most of your power going. You do need

dynamic range and plenty of headroom for the mids and highs, i.e. the amps should still accommodatethe program power ratings of the cabinet, but keep them turned down low. This also applies to bass/midbass above 65Hz or so. Too much midbass gives a system a muddy, ill-defined sound.Finally, never use cabinets that handle mid-high frequencies only. You should have only true "full-range"cabinets, and bassbins in your system. Mid-hi cabinets are useless without a bassbin, which means youcan't use them by themselves for example at a small house party that does not require bassbins. Mid-hi cabinets also do not contribute to the bass response of the system, making them very poorly suited forbass heavy dance music.

II. Do Not Use Active Crossovers or Low Frequency Rolloff Filters with Passive Full RangeSpeaker Cabinets.

Active crossovers are used in almost all systems as a means of filtering out high frequencies passed

to the amplifiers for the bass cabinets, and as a means of blocking low frequencies from going tothe amplifiers for the full-range cabinets. Sealed, horn-loaded bass cabinets sound best when highfrequencies are rolled off at 18 or 24 dB/octave, at a cutoff frequency of 60 to 100 Hz. Using a highercutoff frequency can result in the bass sounding muddy, and in significantly less subbass power handlingcapability. Note that because bass is inherently non-directional in its propagation characteristics, thereis no need to run bass cabinets in stereo. In fact, due to vinyl mastering requirements, the bass soundson almost all records are in mono. This fact is helpful in simplifying the design and setup of systems.When running subs in mono, be sure that the mono source is a sum of the left and right channels. Bysumming the channels together you get a true mono sum signal for the subs (as opposed to running themin stereo or from the left or right channel only), which provides better bass accuracy, and partially cancels


6/20

out low frequency vertical displacement and feedback that occurs with turntables. Also note that in nocircumstances should full-range speakers be run in mono. Stereo is one of the most significant advancesin the history of audio reproduction, but you would be surprised how many sound companies cut cornersand run the entire system in mono, since it is easier to set up and requires fewer amplifiers.Because of Criteria I, we do not require high volume levels at mid and high frequencies. Thus theaverage power level delivered to the full-range cabinets will be lower as a percentage of maximum ratedpower than the average power delivered to the bass cabinets. Because of this reduced SPL requirement,there is no need to run full-range cabinets through an active crossover. This results in much more bassbeing delivered from the full-range cabinets, which is extremely important for the system to have goodtransient response, and clean, accurate bass.Most sound companies rely on the bass bins to reproduce all the bass, and send none of it to the full-range cabinets. Because bass cabinets generally have very low natural cutoff frequencies, and hencevery poor transient response, it is impossible with this approach to obtain clearly defined, accurate bass.In general, only large drivers with high cutoff frequencies, such as 15"s or 18"s cutoff at 500Hz or higher,have the transient capabilities needed to make a system sound really good. The only way to get accuratetransient response from a system which does not have large drivers covering the entire bass range is ifthe system is controlled by a sophisticated processor which has the ability to precisely phase align thevarious drivers. These types of systems are more expensive however and can be difficult to configureoptimally.The second criteria can be summarized as follows:

A. Do not filter the signal going to full-range cabinets.This is one of our golden rules. It is OK to employ a rumble filter (i.e. sharp high pass filter with a cutoffof 15 Hz), though this is usually not necessary because many mixers, processors, and amplifiers alreadyhave subsonic filtering built-in.

Again, do not run the signal going to your full-range cabinets through a crossover. Full-range cabinetsare called "full-range" because they are designed to reproduce the full range of audible frequencies. Mostsound providers, clubs, etc. fall victim to the mainstream industry practice of filtering the lows out fromthe full-range cabinets, and as a result their systems end up with incoherent, flabby sounding bass. Thisunfortunate practice came about for two reasons, (1) to allow full-range cabinets to put out more midbass,and (2) to reduce the likelihood of blown woofers in case of levels getting too high. As we previouslydiscussed however, too much midbass (especially in conjunction with less subbass) gives systems avery unpleasant sound. And in regards to (2), this is a backwards mentality, which makes about as muchsense as running no sound at all to the speakers to insure they can't be overdriven. The better thing to

do is be careful with your levels, and make sure you are using a high quality leveler in your system so thatthe levels cannot go too high even if the DJ cranks everything on the mixer.B. Always use an active crossover or low-pass filter with bass bins.Pretty much everyone knows this, but there have been times that we have played on other people'ssystems and they were running the bass bins full-range. This results in too much midbass andsubstantially diminished subbass, and it sounds terrible. Also make sure the crossover or filter hasa cutoff rate of 18dB/octave or higher, and that it sums the left and right inputs together, so that yoursubbass signal is a true mono sum of both inputs.

III. Avoid the Use of Compressors with Short Release Times.

Most sound system providers mistakenly use a compressor in place of what is called a leveler. A trueleveler is simply a compressor which has the capability of utilizing long (5 Seconds or longer) release

times, thus allowing the system gain to remain fairly stable while still ensuring the output signal leveldoes not go too high. Many compressors simply do not have long enough release times to avoid theloss in dynamic range and pumping effects that result from fast compression. The problem with manycompressors is that they have cheap level detector circuits which do not allow for release times ofmore than 1 or 2 Seconds. Digital compressors are less likely have this problem and can work well aslevelers. Other products such as Auto Gain Controllers or Automatic Level Controllers are also available,but these usually don't add any essential functionality over that of a basic leveler, can be higher in cost,and sometimes don't work any better than a cheap compressor anyhow. Note also that many generalpurpose digital processors are now available which can take care of leveling, parametric EQ, timing/phase alignment, and crossover filtering functions, all in one inexpensive and compact unit. In any case,


7/20

we cannot stress this enough, whatever you use must have a maximum Release Time of at least 5 fullseconds. One product we do recommend is the Behringer AUTOCOM PRO-XL MDX1600, which offers amaximum release time of 5 Seconds, decent audio quality, and a price of under $100. If you have moremoney to spend we recommend the Aphex 320A Compellor.Maximum performance is obtained from a sound system when it is operated at a power level where thebass output is at or near its maximum, without significant distortion or risk of driver damage. Because fewDJs have the sensitivity to consistently maintain the levels at exactly this optimum point, it is necessaryto either have a competent sound person continually monitor and adjust the levels, or use a leveler.Most sound providers find it much easier to use a leveler (or unfortunately as is the usually the case, acheap analog compressor) than to spend the whole night personally monitoring the levels. Still othersound companies will use neither a leveler or compressor, nor personally monitor the levels, but willinstead set the levels fairly low so that even with the loudest record they cannot get too high. This resultsin the system generally being operated at 50% or less of its potential power, and in the levels on themixer being run too high, which causes distortion. A similar but even worse alternative that is oftenemployed by sound "professionals" is the use of lower power amplifiers in the system, such that thespeakers cannot be blown no matter what the input levels to the amp are. A third alternative is installingmechanical or electrical limiting devices in or on the mixer, so that the levels cannot be set at higherthan "7", and the EQ controls are effective only in the negative direction. With the levels set appropriatelyand checked periodically, this approach works well, and results in improved sound quality since the mixercannot be pushed into distortion. The ideal solution is the use of both a leveler and mechanical limiting

devices in the mixer.The reason compressors with short release times make things sound bad is because they cause awidely varying system gain that can fluctuate by a factor of 10 or more between bass peaks and valleys.This results in louder sounds being made quieter, in quieter sounds being made louder, and in theenvelopes of the various sounds being distorted and flattened. The net result is the turning of clear, highdynamic range music into muddy, flat sounding music. It is analogous to turning the contrast all the waydown and the brightness all the way up on a TV set a clear image can be turned into a washed-outconglomeration of light.There are applications where shorter release times are appropriate, such as in microphone processing,or in the mastering of a record or CD, as these will sound louder overall with fast compression. Howeverthis additional loudness is not necessary on a sound system which is already quite loud. Added loudnessat that point will usually make the system sound overly loud and lacking in dynamic range and clarity.

Also worth considering are digital loudspeaker management processors from companies such as dbx,

Behringer, BSS, XTA, and others. These combine crossover and limiting functions into one unit. Be verycareful about these however, particularly with the more inexpensive ones, as they can be very tediousto set up properly and often do not offer adjustable limiter release times. Before buying one make sureit has (1) adjustable limiter release times that will go up to at least 3 full Seconds, (2) crossover bypasscapability for the full-range cabinets, (3) ideally some other built in functionality such as parametric EQand feedback suppression, and (4) that it has a decent size LCD display and can be easily programmedwithout having to spend hours reading through the manual.

An advantage of more expensive sound systems from NEXO, Funktion-One, Turbosound, and other high-end manufacturers is that they have a thorough system design which includes full-featured processorsthat provide optimized limiting, crossover filtering, and timing and phase alignment for each speakercabinet in use. These systems may not offer true leveling functions however, in which case a leveler isstill needed for preventing over-compression.Set your compressor/leveler so there is no more than 3dB of gain reduction when the mixer is at it's

0dB meter reading, with an attack time of around 30mS and a release time of at least 3 Seconds. Thiswill ensure the overall output level is maximized, and that the inter-channel levels will stay balanced.Because cartridges typically have +/- 1.5 dB of inter-channel gain tolerance, not to mention thevariation in the record itself and in the mixer, it is important to have something to compensate for that.

A compressor set for 3dB of gain reduction, infinite compression ratio (i.e. a leveler), and dual monorather than linked operation, is ideal for this purpose. It is important when doing this to ensure that nomore than several dB of gain reduction can result however, or the DJ will not have tight control over theEQ, i.e. if the DJ changes the bass setting on the mixer, the compressor/leveler will compensate in theopposite direction, resulting in the system being unresponsive to the mixer's EQ, and in the mids andhighs "pumping up" when the bass gets quieter. It is also a good idea to put a note on the mixer which


8/20

states something to the effect of "Attention DJ: Please keep output level near the 0dB mark. Goingabove this will not actually make things any louder, but will result in decreased mixer responsiveness andin increased distortion." If the club is likely to have different mixers in use, you may want to post a note inthe DJ booth instructing the DJs to set the levels on the mixer so that there is no more than several dB ofgain reduction that shows up on the compressor/leveler. Different mixers have different gain structuresand thus "0dB" is not the same on all mixers.Perhaps the most important point of all, is to securely lock the compressor/leveler and amps behind aclear plexiglass panel. The DJ should always be able to see the compressor/leveler so it is clear howmuch gain reduction there is, but no one but you should be able to touch the knobs! If you leave anyknobs accessible to anyone it will not be long before you end up with blown speakers, terrible sound,or both. Also do make sure the amps and rack equipment have plenty of ventilation so they will notoverheat.It is a nasty situation that occurs when a compressor is used with too short of a release time or with toomuch gain reduction. Surprisingly however, the mainstream audio industry and the majority of clubs andsound professionals seem to be entirely unaware of this, and run their systems in such a way that theresulting sound is over-compressed, with very little dynamic range or transient detail.In 1996 the Sunsonic MX500 DJ Mixer introduced an Auto Gain Limiter function which ensured themixer output would always be at an optimum level, guaranteeing optimum sound quality and eliminatingthe need for an external compressor/limiter/ALC. This model is no longer available however, and for anumber of years no other DJ Mixer manufacturers offered this feature. Rane stepped up and introduced

this feature into their MP44 DJ Mixer, though its release time is very short, making it necessary to modifythe internal limiter circuitry for it to be of any use.

Developed in 1996, the Sunsonic MX1200 Professional DJ Mixer was the first DJ mixer to include anAuto Gain Limiter levelling system, and a joystick Cue Source control.A simple yet very effective and high quality internal leveler can be added to DJ Mixers by an electronicsexpert. Install an internal motorized volume control (such as those found in most consumer StereoReceivers), which is set to reduce the output level if the topmost LED's light in the mixer's level meters.Then use a buffered RC circuit to slowly return the volume control to its normal setting. (We can supply

a parts list and schematic at no charge, or can make this modification to a mixer for you should younot have access to a local electronics expert.) This is a highly cost effective approach which has theadvantage of leveling the signal in the mixer, as opposed to after the mixer, where the signal may alreadyhave gone into distortion.

IV. Place Speaker Cabinets as Closely Together as Possible.

Sound is simply the variation of air pressure. Because air is relatively thin, pressure differentialspropagate through it relatively slowly. (Sound travels at about 1000 feet per second in air.) A difference


9/20

of only 30 feet between two speaker cabinets thus results in a delay of 30 milliseconds between whenthe sound from one will arrive at the other. If the effect of such a delay is examined on a sound such asa snare drum or hi-tom, it is obvious that the combining of two such sounds with delays of more than afew milliseconds between them has destructive results. Many clubs fall victim to the "let's put speakerseverywhere" mentality, and have speakers separated by distances of 100 feet or more. If viewed from amusic theory perspective, it is clear that a 100 foot separation results in approximately 100mS of delay.For even a fairly slow tempo of music, such as 120bpm with a 4/4 signature, 100mS equates to almosta full 1/16th note! Few people would disagree that any band or DJ who was always 1/16th note off,would be kicked off the stage. Clearly then it should be an emphasis of good club design to minimize thedistances between speakers.

As a side note, to clear up a couple of misconceptions we often run across, adding delay to one speakerwould not fix this scenario. It might work if you always stood a certain distance from each speaker, butanywhere else and it would likely sound worse. Also note that delay occurs in the air, not in the speakerwire. (Electricity travels almost one million times faster in wire than sound travels through air!)

A follow-on point to this is that it is always better to use a small number of high powered speakers thana larger number of lower powered speakers. The greater the surface area from which sound is radiated,the larger will be the delay spread, and the more drastic will be the resulting timing misalignments andinterference patterns. This is analogous to dropping stones into a still pool of water. If only one stoneis dropped in, a single group of pristine circular waves will radiate out. If several stones are droppedin however, a complex pattern of frequency dependent nulls and peaks will be created, and the waves

from each source will arrive at different places at different times. We have played on many "patchwork"systems which have 20 or more cabinets seemingly from numerous manufacturers and various historicaleras, and it is often surprising how little sound can come out of so many cabinets, and how poor theoverall sound quality is. A simple system with 4 T-36s and 2 double 15" full range cabinets will generallyput such systems to shame.Sunsonic systems are always set up in one of two configurations:A. A single row of bass bins with full range speakers at each end (on top): This configuration delivers themost accurate and most intense bass, because all the bass bins are right next to each other. With 6 or8 bass bins, there is still plenty of separation between the full range cabinets to deliver excellent stereoimaging.B. Two stacks of speakers, separated by no more than 25 feet. This is a less desirable setup for smallersystems, but works well for larger systems.For maximum bass response, always place all bass cabinets on the floor, with their backs directly against

a wall, and preferably in a corner. The lower the air volume within one wavelength of a bassbin (i.e.within about 30 feet), the better the impedance match will be between the air and the bass drivers. Asa result, two things will happen. First, the acoustic power conversion efficiency of the drivers will go upexponentially due to the improved impedance match of the low impedance cone driver to the normallyhigh impedance air. Second, the relationship between bass SPL and distance from the cabinet willbecome more linear as opposed to inverse exponential. This means the bass will travel further, due tothe horn loading effect created by a corner made by two walls and the floor. In this type of corner, a bassspeaker only has to push air in 90 degrees in each axis, i.e. it is 1/8th space loaded. An 1/8th spaceloaded bass cabinet will have several times the acoustic power conversion efficiency as a 1/2 spaceloaded (i.e. on the floor but not near any walls) cabinet. Considering these points, it's clear that you canget much more bass from the same bassbins simply by placing them optimally.Note that for smaller sound systems the DJ does not necessarily need to be behind the speakers. Ravesand clubs are often set up this way, but it can be counterproductive to use this approach for dance

music. If the speakers are backed against a wall for example, and are facing the DJ, it is not a problemfor the DJ if he or she has a good loud monitor (with a separate booth monitor level control on the mixerof course). In fact, this set up is preferable to many DJs, as they can then between mixes for exampleturn down the booth monitor and hear the main speakers exactly as the audience is hearing them.For larger systems however it is better if the DJ is not overwhelmed with sound from a huge systempointed right at him/her. It is easier for DJs to mix if the ambient SPL is fairly low compared to the DJmonitor level. The monitor should be clear, not too loud or too quiet, and there should not be too muchreverberation or reflection from nearby walls.

A final note relating to speaker placement is to avoid at all costs setting up two systems in the sameroom. Because of the logarithmic sound perception mechanisms of the ear, it is ruinous to the music


10/20

and sound quality in both areas if significant acoustic coupling exists between them. The only practicalsolution for this is to insure there is a completely separate room for each system (i.e. a full floor-to-ceilingwall between them), or, if the systems are outdoors, that cabinets from different systems are always atleast 50 feet apart and facing opposite directions.

V. Take all steps to insure feedback will not occur with turntables.

Sound systems that put out more than 1,000 Watts of bass must have solid, vibration-proof footing for theturntables, or feedback can occur. There are several approaches to solving this problem. Without them,the power handling capacity, dynamic range, and accuracy of the system can be drastically reduced.One approach to preventing feedback is to use an electronic feedback destroyer (a.k.a. feedbacksuppressor or feedback eliminator). There are now many models available at low prices. Note howeverthat feedback suppressors are a secondary fix, which attempt to address the symptoms of feedback, butnot the cause. If the turntables are on solid footing, the system will be cleaner sounding, more stable andaccurate, and will not be dependent on a feedback destroyer to fix everything.The ideal footing for turntables is a vibration-proof table placed directly on a concrete floor or on theground. Vibration-proof materials include cinder blocks, which are cheap but heavy (making them betterfor permanent installs than for mobile sound systems), or wire shelving (such as Metro or Nexel), whichalso has many accessories available such as wheels or rack mount rails. With wire shelving it helps toweigh the bottom shelf down with some cinder blocks, sandbags, or your amplifiers, so the needle willbe less likely to skip if the table is bumped. A more cost-effective table can be made from an ordinarybanquet table by securely attaching 4x4s, or 4 or 5 layers of 3/4" 2'x6' pieces of particle board to thetop. Another option is to pour 1" or so of concrete into the bottom of a DJ coffin. Note that the turntablesshould not be left inside of a DJ Coffin which has not been reinforced like this. DJ coffins are usuallymade of thin wood that easily vibrates and conducts feedback. The foam lining inside some cases canalso be deceiving it looks like it should reduce feedback, but in reality it can allow feedback to bypassthe vibration dampening systems that turntables have built into the feet. Set the turntables directly on thecinder blocks/concrete/4x4s/wire table, and make sure these are on solid ground. Stages, scaffolding,etc. should be avoided when possible.What the turntables are placed on can be just as important as anything else in the sound system. Wehave seen sound companies bring 10 or 20 cabinets to an event, and then put the turntables on a flimsytable. Feedback then occurs, requiring the levels to be kept turned down below the point of noticeablefeedback. In this scenario the 10 or 20 cabinets that the promoter paid to rent, and the sound company

spent hours moving around and setting up, are not putting out half the power they could, and sound bad.There might as well have been half as many speakers.For venues that do not have solid flooring available, the floor will conduct feedback, and you will needto use some sort of cushioning material to isolate the turntables from the floor. Another alternative inthese cases is to suspend a rectangular structure of 4x4s from the ceiling using chain or rope. Theturntable feet should rest directly on the 4x4s. This is also good for preventing needle skips from the floormovement that occurs from people jumping up and down when they are dancing. Keep in mind that eventhough a stage or wooden structure may appear solid, unless it is concrete or dirt, or very thick wood (4"thick or more), bass will still vibrate it and feedback can result.We have done testing of various materials which are available for preventing feedback, and summarizedthe results in the table below. For this test, a Cerwin-Vega T36 bass bin was placed 2 feet from astandard 2' x 4' particle board banquet table, on which were placed 2 Technics SL1200 turntables. Theneedle was put in the last inner groove of a record where it loops continuously and there is no music.

The floor used for the test was carpet above a thin layer of concrete and wood. The system gain wasthen increased until just before the incidence of significant sustained feedback, and the gain was noted.The winner of the test is a new product released Aug. 2003 in the US called "FREEFLOAT" (see picturebelow). These are inexpensive and work great (available from United Record'sAccessories Page.)One issue with these however is that they can go flat, so it is good to have a backup in place such assome foam cushions underneath. They also make the turntables somewhat wobbly, which might beannoying to some DJs (especially scratch DJs), although they work great for us and we have not heardany complaints from DJs who have used them.
http://www.unrec.com/bins/accessories.htmhttp://www.unrec.com/bins/accessories.htmhttp://www.unrec.com/bins/accessories.htmhttp://www.unrec.com/bins/accessories.htm


11/20

Material Threshold of feedback Improvement infeedback isolation

FREEFLOAT air cushions -2 dB 22 dB

DJ Coffin withFREEFLOAT air cushionsinside

-2 dB 22 dB

Two Small patio cushionsper turntableeach 2' x 4' x 1", folded to2' x 2'

-7 dB 17 dB

DJ Coffin on two smallpatio cushionseach 2' x 4' x 1", folded to2' x 2'

-9 dB 15 dB

One small patio cushionper turntable,2' x 4' x 1", folded to 2' x 2'

-11 dB 13 dB

DJ Coffin on 1 large patiocushion, 2' x 6' x 2"

-11 dB 13 dB

Turntables on 1 large patiocushion, 2' x 6' x 2"

-14 dB 11 dB

DJ Coffin on top of 4 tennisball halves

-16 dB 9 dB

5' Metro wire shelf on 1large patio cushion, 2' x 6'x 2"

-18 dB 6 dB

DJ Coffin, with turntableson tennis ball halves

-21 dB 3 dB

Turntables on springsuspended wire shelfsystem

-22 dB 2 dB

No isolation (Turntables onbanquet table)

-24 dB 0 dB (reference)

DJ Coffin on banquet table -26 dB -2 dB

Putting the DJ Coffin on top of 2 small patio cushions works well (a 15dB improvement in this test) whileallowing the turntables to remain very stable. The FREEFLOAT cushions are more wobbly, but are betterfor very large sound systems or exceptionally flimsy flooring. This test likely is not highly representativeof other sound system configurations, and does not consider other factors such as skip resistance fromshock. The FREEFLOAT cushions however were specifically engineered to reduce feedback by a hugeamount, while remaining stable enough that the additional slight wobbliness does not seem to botherDJs and does not ever seem to cause the needle to skip even when cueing records and shaking the

turntable. The FREEFLOATs are truly a fantastic product that no sound company should ever be without.


12/20

Keeping the bass bins at least 15 or 20 feet from the turntables can be helpful with larger systems, asheavy subbass can vibrate the turntables themselves, regardless of what they are on. As is mentionedin other sections of this document however, in order to minimize intercabinet delays the bass bins shouldnot be more than 30 feet from the DJ or from each other.

VI. Use as Few Processing Components as Possible.

The ideal sound system consists of turntables, a mixer, leveler, low-pass filter or crossover (for the basscabinets only), amplifiers, and speakers. Nothing else. Many sound providers think that the more EQs,compressors, dynamics processors, and various other fancy looking devices they can put in a rack, thebetter. While many types of processing components do have their proper place, generally they do moreharm than good if not used in exactly the correct manner.Each piece of equipment that is added to a signal chain causes phase and dynamic range degradationof the original signal. Considering the high level of production quality with which most undergrounddance records are produced, there is rarely a need for processing of any kind. An exception to this is forequalizing a small room that has bad resonance peaks in the frequency response. Generally however,an EQ will do more harm than good. Even if a room is optimally EQed with a Real Time Analyzer or othertools, that does not always mean it is going to sound good. As the room becomes filled with people,as different tracks are played, or depending on where you stand in the room, an "optimized" EQ setup

can end up sounding worse than if no EQ was used at all. If used minimally, with the settings closelymonitored as the event progresses, EQs can be beneficial, but otherwise they are more often misusedthan used correctly. Perhaps one of the most inappropriate uses of EQs is for boosting the low and highfrequencies (i.e. the infamous "V" curve). Apparently, many sound providers have lost much of theirhearing capability in the high frequency ranges, because they seem to think it is necessary to boost thoseranges by as much as 10dB. Another problem with EQs is that they are often designed such that thesignal is passed through each filter one by one, each of which introduce some phase degradation. If youmust use an EQ, use a Parametric EQ with 3 to 5 variable Q, sweepable bands. These are better formost EQ applications and have better phase performance.On a related note, we highly recommend the use of active / self-powered speaker systems (speakersthat have built-in amplifiers). These can provide large increases in accuracy and power output, and atthe same time greatly simplify system setup. (We recommend Meyer's MTS-4As, though they are a bitoverpriced, and very heavy.)

Worthwhile of mention again is that an inexpensive system controller (a.k.a. loudspeaker managementprocessor) can in fact handle all the signal processing requirements of even a large sound system.Because all processing occurs digitally inside a single mixer/processor at high bit depths, there is lessdegradation in signal quality and reliability than would occur with several processing components chainedtogether.

VII. Minimal Phase Delay Crossover Networks Should be Used in Full-Range Speakers.

The higher the order of filtering in a speaker's crossover network, the higher the level of phase distortionthat will result. The derivative of phase delay is group delay. If a sound system does not have a constant


13/20

group delay, different delays are induced to different frequency components of an audio signal. Thisis much more detrimental to dance music than most other types of music, because percussion is itsmost important element. Percussion sounds in general are defined by an initial large amplitude impulse(caused by the striking of two surfaces together) followed by a decaying resonance (caused by one of thesurfaces oscillating at its natural resonant frequency). An impulse is the only kind of sound that does nothave a characteristic frequency in fact, if an impulse is evaluated in the frequency domain, it is seen toconsist of all frequencies simultaneously. When such a sound is fed to a bass cabinet and a full rangecabinet, the sound will pass through the various crossover filters to each driver in each cabinet, where therespective frequency components will be radiated. The more filtering done in each crossover, the greaterthe delays and time differences generally will be between when each component is radiated from eachdriver. Without minimal phase delay crossovers, the initial precise millisecond "kick" of a clean kick drumsound will come out of each driver at different times, resulting in an incoherent, loose, and unrealisticsounding drum.The reason sharp cutoff filters are used in most full-range speakers is because they allow higherbroadband power levels to be sustained by each driver. For the purposes of dance music however thereis not as much need for exceptional power handling capability in the mid and high frequency drivers.(We use overload protection circuits on these drivers anyhow.) Often it is not practical to replace existingcrossover networks within higher-end speaker cabinets, because they are usually highly customized tothe electrical and acoustic properties of the cabinet and drivers. Replacing them with generic minimalphase delay crossovers can result in degraded frequency response and may circumvent overload

protection circuitry in the original crossover. Some high-end cabinets are often designed with somephase correction built into the crossover system (or they can be run bi-amp/tri-amp, allowing for precisephase correction to be done in an external processor). These types of systems may sound fine even ifnot a minimal phase design. But for most cabinets, going to a minimal phase design can often make ahuge improvement in sound quality. If in doubt, hire an experienced Electrical Engineer to evaluate thesystem phase response, and if necessary, modify the existing crossovers to a 6dB/octave design withcharacteristics closely optimized to the cabinets and drivers.Often a good time to upgrade to a minimal phase crossover is while other repairs are being made. Atype of speakers used by Sunsonic in the mid-90's for example were a pair of Sonic double 15" full rangeboxes using a Peavey 22XT compression driver. The 22XTs have a very harsh sound and a pole in thefrequency response at 8KHz. After a lot of use the seams in the cabinets started coming apart due to thevibration, and the cheap wood and construction practices with which they were made. The crossoverswere mounted on plastic mounting cups, which had become heavily cracked. The existing crossovers

were recycled and replaced with a Sunsonic designed and built 6dB/octave crossover with a 750 Hzcutoff frequency, a compensation circuit for the pole in the 22XTs frequency response, and a light bulboverload compression circuit. (Light bulbs are natural power compression circuits their resistanceincreases in proportion to filament temperature). This was all assembled onto a metal mounting plate,using RTV sealant and 12 gauge stranded wire throughout, and the cabinets then reinforced with screwsand wood pieces. The cabinets then delivered hard, precise bass and percussion that would be expectedonly from a $1,000+ cabinet (but at a cost of only $350 plus $50 in parts). An A/B comparison was donebetween the first cabinet after it was done and the second before taking it apart, and the difference wasamazing.

An exception to this criteria can be made in cases where the crossover filtering is done in a high-enddigital processor which can apply timing and phase corrections based upon manufacturer-suppliedparameter settings specific to each speaker cabinet. Note however that these types of systems aresubstantially more expensive and can sound bad if not configured correctly.

VIII. Amplifiers should be able to supply the program power rating of the speakers.

Accurate reproduction of percussion is the most important requirement of sound systems for undergrounddance music. As was mentioned before, the major defining element of percussion sounds is their initiallarge amplitude impulse. Accurate reproduction of impulses requires a system with very high dynamicrange and high available power. For this reason, amplifiers must be matched to speakers such that eachspeaker has available to it at least its full rated program power. (Program power is generally defined astwice the continuous rms power rating of a speaker.)


14/20

In the case of bass bins, Impulses are of such short duration that they are mostly filtered out of thesignal going to the bass bins, so they do not technically need as much headroom as full range cabinets.However, bass bins are more likely to present large reactances and greater average power consumptionthan full-range cabinets, and so this criteria applies to them as well, if for slightly different reasons. Ifyou had an unlimited budget it would be even better if your amps were able to supply the full peak powerrating of the speakers (peak power is generally defined as twice the program power rating of a speaker,or four times the continuous rms power rating), but the difference in quality will generally be insignificantenough that the added expense would not be justified.

Amplifier power ratings are different for different load impedances. Due to increasing resistance in drivercoils as their temperature increases, and irregularities in driver impedance curves, impedances seen byan amplifier are often substantially higher than expected. In addition, voice coil reactances can causemomentary impedances to be presented to an amplifier which are equivalent to 4 to 10 or more timesgreater of a load than the speaker's rated impedance. As such it is suggested to not run amplifiers attheir lowest rated output impedance. For an amplifier to maintain tight control over a voice coil in theseconditions, it must have plenty of available headroom, a very high damping factor, and the speakercables used must have near-zero resistance. (We use only 8 AWG (6.5 mm2) cabling to subbasscabinets.) Also note that only heavy gauge AC Power extension cords should be used. We advise theuse of no smaller than 10 AWG (4.0 mm2) extension cords. Using thinner AC Power cords than thatcan cause significant voltage drops and can result in your amps clipping much sooner and in their poweroutput capability being reduced by 25% or more.

As an example, to drive 4 full-range speakers which each have a 4 Ohm nominal impedance, and 1000Watts program power handling, an amplifier capable of delivering at least 2000 Watts per channel at 2Ohms is required for optimal sound quality. Note that you must know what your amplifiers can put out atall load impedances. For example, an AB Intl. 9620 Amplifier is rated as follows: 2000 W/ch @ 2 Ohms,1500 W/ch @ 4 Ohms, or 900 W/ch @ 8 Ohms. A Cerwin-Vega T-36/750 bass bin is rated at 1000 WattsProgram power at 8 Ohms. If you wanted to push 4 T-36s from an AB 9620, that would be a 4 Ohm loadper side, which would give you 750 Watts into each T-36. If you did not take the load impedance intoaccount, it would be easy to make the mistake of thinking that it is a 4,000 Watt amp, and so it should beperfect for driving four 1,000 Watt speakers. This would be true if the speakers were each 4 Ohms, but T-36s are 8 Ohms. As a result, an AB9620 is not enough to make 4 T-36s sound as good as they can. Wehave done side by side tests with bigger and smaller amps and you really can hear the difference. Bassbins sound tighter and cleaner when they have plenty of available power behind them. A Crest Pro 9001,Pro 9200, QSC Powerlight 6.0, Crown Macro-Tech 5002VZ, Lab-Gruppen fp6400, or Camco Vortex

6 would be much better for pushing 4 T-36s. The problem is that T-36s have an unusually high loadimpedance for their power rating. This means you either need a 5K or 6K Watt amp (in stereo mode) topush them comfortably, or you could instead use 2 smaller amps in bridge mode. For example a CrestCA9 or Crown K2 in bridged mode would be an excellent match for 2 T-36s.Note that most amplifier manufacturers make several different grades of amplifiers. Consumer gradeamplifiers should be avoided at all costs, as they can easily overheat and shut down and their audioquality is not as good. If you have a little more money to spend, look into CAMCO, Lab-Gruppen, orCrest's Pro 200 Series amplifiers. These are also very high quality, but are much lighter and easier totransport.

System Frequency Response Optimization

The frequency response of a sound system is not a constant function within any venue. Essentially

there are two elements that determine overall frequency response of a sound system within a venue.Unsurprisingly, these two elements are the sound system itself, and the venue.

A sound system that is set up according to the Sunsonic Criteria, and that employs well designed, highquality system components, will exhibit an acceptable, even frequency response. What this means isthat the ratio of output level of the system to input level will be fairly constant regardless of the frequencyof the input signal. However, there are a number of issues that make this all more complex than manysound equipment manufacturers might like you to think.

Almost all sound systems have substantially different directivity at different frequencies. Very lowfrequencies have omnidirectional propagation characteristics, whereas higher frequencies can be moreeasily directed. This is simply due to the fact that to manipulate the directivity of a sound wave, a horn


15/20

structure is required. The size of a horn structure required to implement a given directivity is proportionalto wavelength, which is inversely proportional to frequency. To provide a high degree of directivity at afrequency of 20Hz for example, requires with a horn structure with a throat length of over 30 feet. Theresult with most sound systems is then generally that the full range cabinets are much more directive thanthe bass cabinets, so if one stands far from the speakers, along the axis of the horns in the full rangecabinets, the bass will be much lower relative to the mids and highs. In contrast, if one were to standnear the speakers, but to the side, and hence not on the axis of the horns in the full range cabinets, thebass would be much louder than the mids and highs. So, in this type of system, there is already a largeamount a variation in the frequency response of the system based simply on where the listener happensto be.The fix for this issue is simple: Use full range cabinets that have low directivity. This ensures allfrequencies are radiated with fairly equal intensity across the entire view of the speaker cabinet.For very large sound systems, frequency response and SPL uniformity concerns become major designissues. However, upon review of the "Characteristics of Dance Music" Section in this document, itbecomes clear that SPL uniformity is not always our goal. Thus these design issues, which can bevery complex, are not much of an issue typically for underground dance music. In a sense then, the oldprinciple of K.I.S.S. (Keep It Simple, Stupid) proves itself here to be true.

Phase Checking

Each speaker in a system should have consistent phase response, and be driven with a phase correctsignal. Otherwise, cancellation will occur, as one driver may be pushing air while another is pulling. Thiscan have very noticeable impacts on the system frequency response, bass SPL, stereo imaging, andoverall sound quality.Systems that have multiple models of amplifiers, speakers, cables, etc., can very easily have phaseerrors among different system components. This is mainly due to speakers, amplifiers, or processingcomponents having differing polarity conventions due to design differences or wiring errors, or can be dueto connection errors among system components.To avoid these issues, it is necessary to fully characterize the input-output phase relationship of eachcomponent in the system, all the way down to the cartridges on the turntables (which could have thecartridge lead wires reversed on one channel, but correct on the other, causing Left and Right channelsto be 180 out of phase), up to the individual drivers in the speakers (which may have had a driver unitreplaced at some point and the lead wires connected incorrectly, or a crossover replaced with a different

design). It is suggested to enlist the help of an electrical engineer for this task, as this process canbecome complex.Ideally, the entire system will consist of entirely top-grade, perfectly maintained equipment and cabling,for which the phase specifications are very clear. This is often not feasible however, due to the limitedbudgets that many sound providers are constrained by.

A simple method for checking whether a component is phase inverting or not is to connect a SignalGenerator to the input, and observe input and output (simultaneously) on an Oscilloscope at variousfrequencies such as 20Hz, 600Hz, and 20KHz. If a Signal Generator is not available, use a Synthesizeror a test tone record. If an Oscilloscope is not available, use a Multimeter to read the AC Voltage on theinput first (let's call this Vin), and then on the output. Then adjust the output gain until the output Voltageis the same as the input Voltage. Then measure the AC Voltage between the input and output (let'scall this Vdiff). The magnitude of the phase difference is then approximately 180 times half of the ratioofVdiffto Vin. In the case of measuring output from a speaker, use a microphone and microphone pre-

amp as the input to the Oscilloscope or Multimeter.

Grounding, Ground Loops, and Noise

This topic is not specific to underground dance music, but is worth a few paragraphs here becausethough it is a simple issue, most people are completely unaware of how to fix noise problems that occurdue to ground loops. Ever hear a loud hum or buzz after you connect a stereo or sound system to othergear? It was probably because of a ground loop somewhere in the system. Ground wires are present inmost power cords and signal cables, and if ground wires are connected such that they create a loop, that


16/20

loop will act as an inductive coil that converts magnetic noise into electric current. Residual magnetismfrom AC power lines and nearby electrical devices then gets converted into noise currents on your powerand signal cables.There are many different ways that different audio, video, computer, etc. equipment can be designed,and some models are more vulnerable to conducted noise than others. The important thing to rememberhowever, is that every single piece of electronic equipment in your system, MUST HAVE ONE ANDONLY ONE ground connection. Generally in a small system, only the mixer should be grounded to an

AC outlet, i.e. with a 3 prong power plug. Any turntables, CD players, and microphones then plugged intothe mixer will then be grounded through the mixer's ground, by way of the Ground wire, or "shield" in theaudio cable.Now let's say you run an audio cable from that mixer into an amplifier that also has a 3 prong powerplug. If the amplifier does not have a "Ground Lift" switch that is "lifted", you now have a ground loop.In this case, the loop is a triangle that is formed by ground wires in the 2 power cords and the groundwire or shield in the audio cable between the mixer and the amp. To fix this, you have to break theloop. By "lifting" the ground on the amp, it will still be grounded through the audio cable to the mixer, butthe ground loop will have been broken because the ground wire in the amp's power cord is no longerconnected to the signal ground. If the amp does not have a ground lift switch, you can use a ground dropadaptor, i.e. a 3 prong to 2 prong adaptor. These are available for less than $1 at any hardware storeand at many grocery stores, for allowing 3 prong plugs to be used with older style 2 prong outlets. Notethat most consumer mixers have 2 prong power plugs. In this case make sure that at least one of your

amps is grounded with a 3 prong plug, and that if it has a ground lift switch that it is not "lifted".Very important to note however, is that you must be sure you have one ground connection for everything!One too many grounds, and you have a ground loop, and probably hum and noise. But if you have toofew grounds, there is potentially a very serious safety hazard, where someone could get electrocuted!Proper grounding is a subtle, but extremely important issue that must be taken very seriously. Westrongly advise that you consult an Electrician or Electrical Engineer if you are unsure about anythingrelating to how to properly ground your equipment.

Feng Shui

The layout and design of a sound system, and the positioning of speakers, lighting, dance floor areas, theDJ, etc. should be designed with higher concerns in mind, such as the comfort of attendees, the designthemes of the event or club, and particularly any spiritual or religious themes associated with the event,

music, or attendees. As far as the underground dance community is concerned, this means the soundand lights must not be overbearing or intrusive, or otherwise obstructive to a positive, open environment.Copied below is an example of this relating to Feng Shui, from a promotional magazine published by NewYork's Club Twilo:

"FENG SHUI FOR THE NIGHTCLUBBER:Hang your mirror ball at least 12 feet from the dance floor. This will ensure that all the positive energyreleased through your scalp will have space to dissipate. Too many positive waves crushed into a smallamount of air have the ability to generate a friction that may lead to sudden mood swings.Speaker stacks, as a rule, should only ever be placed on the dancefloor itself. Never hang from theceiling or attach to a wall. Sound frequencies must be allowed to enter through your toes first, neverthrough your ears. This will boost your chakra from below and elevate you mentally.Neon lights, strobes, and rotating pin spots should work on a cycle, and be evenly spaced. Lights thatare placed too tightly together counteract with your aura and this leads to a negative feeling. Avoid this

by measuring carefully. Remember to only mix pastels with pastels and primaries with primaries."These points make intuitive sense if you think of different clubs you have been to which were or werenot designed along these lines. Perhaps the greatest design weakness of many club sound systems isthe concept of hanging speakers at heights of 10 feet or more. These speakers cover the audience withmore than enough mids and highs, while providing a disproportionately lower level of bass and subbass.By placing all speakers on the dance floor only, with a number of good bassbins standing directly onthe floor, and the full-range/mid-hi cabinets directly on top of the bins, the sound is then felt as much asheard, and the mids and highs are not so loud relative to the bass and subbass. For example, if youwere to stand 20 feet from a stack of speakers, you would have basically the same view of the mid-hi/full-range cabinets as the bassbins, and as such, the bass would remain proportionate in volume to the mids


17/20

and highs. If however, the mids and highs are being radiated from above the audience in a direct pathto your ears, several things occur: First, since bass bins are placed on the floor in almost all clubs, thebass is then partially blocked and absorbed by the audience, but the mids and highs are not. Second,the high frequency drivers used in most club systems are highly directional, whereas bass and subbassfrequencies are omnidirectional by nature. As a result of these factors the bass and mids/highs becomeinconsistently matched in terms of volume, and at same time have less coherence and clarity. If you thinkback to times you've been really amazed by a sound system, more often that not it's because you heard iton a system providing a solid level of bass and subbass, that allowed you to really feel the music.

As underground venues become more restricted by the political powers that be in many cities, clubs areincreasingly where events/parties are held. Because club sound systems are typically permanent installs,they are more likely to employ overly complex and overbearing speaker placement strategies. (It maybe a surprise to many, but there are people who don't go out to clubs much anymore because they aretired of sound systems that are too loud (mids/highs cranked up too high) or that just don't sound good.)Second, if it is a permanent install, the effects of such designs are long term as well. Note that most clubmanagers, owners, and promoters are not aware of any of this, so make it a point to bring these issuesto their attention whenever you happen to go to a club that has one of these rock-concert style soundinstallations.

Another advantage of placing speaker stacks on the dance floor, rather than in numerous elevatedlocations throughout a venue, is that the sound is then radiated from a smaller, closer array of locations.This insures that the timing between the sound sources is better aligned, and as a result, that the

clarity of the system is maximized. Because sound travels at only about 1 foot per millisecond in air,a difference of 50 feet for example between two speakers will cause a delay of up to 50 millisecondsbetween when a listener hears the signals from each. Combining multiple signals together with delaysof that order is destructive to the transient response (a.k.a. "impact"), frequency response, and clarity ofa sound system. In some large venues these timing differences can be so large that in some areas thesound from different speaker stacks (and/or wall reflections) combines such that it sounds like a constanttrainwreck. The cure for this type of sound system is combining all the speakers into no more than 2stacks, which are spaced no more than 30 feet apart. Walls that are overly reflective should also becovered with acoustic foam, carpet, or some other sound absorbing material.

Frequently Asked Questions

Question:

How do you feel about the Cerwin T-250 to go with T-36s as a mid-high cabinet? Is there a better choicefor (underground) dance music?Answer:The problem with the T-250 is that it has a cutoff of 90Hz, and because it has only a 10" driver, does nothave much ability to move large volumes of air, so you simply can't get percussive impact from it. TheV-253 is definitely a better choice. That has a cutoff of 35 Hz, and would definitely give a fuller, richersound than the T-250. The other thing is that the V-253 is a full-range cabinet, whereas the T-250 isnot. An advantage of full-range cabinets (aside from the fact that you get a lot more bass and percussiveimpact), is that for smaller gigs (a house party for example) you can bring just the full-range cabinets, andthat's all you need. The T-250 is only a mid-high cabinet and thus it is completely useless by itself.Question:I've been reading and learning a lot about the technical side of building a system that is loud, crisp andhard to blow up. We have very limited resources, so we might build the speakers ourselves. We will

probably use the old Fane book for speaker designs.Comment:Keep in mind that it's a lot more difficult than it looks if you want them to sound really good and be verysolid electrically... But, it's a good learning experience, so if you have a lot of time to spare, it might beworth it. Many speakers on the market have literally decades of engineering behind them though, so youwill have to do a lot of research and testing and fine tuning if you want yours to sound as good. Also, itdoes end up being pretty expensive building your own anyway, once you add up all the dozens of partscosts (which you pay retail for but manufacturers buy in bulk and pay wholesale for). What you spend willbe probably 80% or more of the cost of just buying some good speakers outright.Question (continued):


18/20

For starters we are planning on building a 3-way system, with 2 18" W-bins, 2 double 15" courtbins, 2double 12" mid-low speakers, and 2 speakers with a horn and a bullet tweeter in them, using a passivecrossover to split between the horn and the bullet. So I need a 3-way crossover, right?Answer:First off, we advise against using separate cabinets for everything. Also, stay away from non-sealedbass bins. They are much easier to blow than sealed designs (such as the Cerwin-Vega SL-36). L36style cabinets are more efficient and put out twice the bass, due to their exponential folded horn design.We strongly recommend going with SL-36B or T-36 bass bins. Also, for what you get, I think they arepriced very reasonably. So, put the mid bass, mid, and high drivers in one cabinet, and then yes, you'llneed a 3-way passive crossover inside that cabinet. Use a 500Hz - 750Hz crossover frequency on thebass drivers, and be sure to use a 6dB/octave passive crossover design. (www.the12volt.com is a goodwebsite by the way which has lots of info on building crossovers.)Question:You say that you never use crossover modules in the signal chain for full-range cabinets. I understandthe reasons completely, yet in the manual for EV Eliminator cabinets, they say that we have to filter anysignal below 40Hz because the Eliminators cannot handle subbass frequencies. Have you worked withEliminators and do you really run straight signal into them?Answer:Definitely. The driver may not be able to handle as much power at 30Hz then at 50Hz, but that's fine

just run it at a little less power. It's much better that it put out as much low frequency bass as it can,

than it put out a bunch of midbass. Look at it this way: Those 15"'s should be putting out the exact samewaveform that a kick drum would.So is EV wrong to suggest filtering out the subbass? No, they are just trying to prevent incompetentsound people from blowing out their speakers. But if you know what you are doing, know the limits ofyour speakers, and you configure your system properly, then you don't have to worry about that, and theywill sound better as a result.Question:How much RMS do you recommend supplying full-range cabinets from the amps? How do you ensurethat the drivers won't blow?Answer:It is easy to tell because the speakers will sound like they are distorting. If you have a good ear forthings, then after a while you just get a feel for when a speaker is at its max. Then just back it off a fewpercent to be sure. Also, the amps should never be run such that the clip/limit lights flicker more than

occasionally. If your amps are rated for the program power of the speakers, and you set them so the clip/limit lights very rarely come on, and the speakers sound good, you're all set.Question:I am trying to build some folded horn subs like the Cerwin-Vega SL36 but I can't find any plans. Can youhelp?Answer:I would not recommend building your own unless you have A LOT of time on your hands. It would takeyou probably 50 - 100 hours of labor for each one, and cost you 80% or more of what new ones would.You might be surprised how the parts costs add up. Cerwin-Vega does high quality work, that can't bematched unless you have about $20K in shop equipment. Also, the drivers they use are very good, andexpensive. If you don't use the same or very similar, they won't sound good. We have seen (and heard)some homebuilt L36s and they are junk compared to the real thing! If you still insist on building your ownthough, here's a drawing: www.unrec.com/sunsonic/l36.gif

Question:We bought an old JBL rig consisting of 4 W-bins, 4 mid cabs with one 12" driver each, 2 horns with a 2"compression driver each and 2 high cabs with two bullet tweeters and a 1" compression driver each.We want to run the rig 4-way. The bullet tweeters have filters to split the frequency, but the rest doesn'thave any filters. We were thinking of buying 2 Behringer crossovers, which are 4-way mono, and haveadjustable cutoff frequencies. What crossover frequencies do you recommend?Answer:Don't buy an active crossover, unless you use it only as a low pass filter for the bass. The Behringershould be fine, although make sure you can return it if you don't end up liking it. For your bass signalall you need is a cheap active crossover. For the mids, buy or build some simple 6dB/octave passive
http://www.the12volt.com/http://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.unrec.com/sunsonic/l36.gifhttp://www.the12volt.com/http://www.the12volt.com/http://www.the12volt.com/http://www.the12volt.com/http://www.the12volt.com/http://www.the12volt.com/http://www.the12volt.com/


19/20

crossovers. Run the 12"s up to around 2 or 2.5 KHz, and the horns above that. For exact frequenciesto set your crossovers at you should look at the frequency response graphs of the different drivers andsee where they start to fall off. Pick the crossover frequency such that your combined response fromboth drivers is maximized. On the high cabinets just use a 6 or 12 dB/oct passive crossover with a cutoffof 10KHz or so. On the mid cabinets, don't filter out the bass or highs. One 6db/oct crossover for eachcabinet is all you need. 6dB/oct. passive crossovers are very inexpensive, because it's only 1 part aninductor for low pass or a capacitor for high pass.The passive crossover approach will save you money, make things easier to connect, and you won't needas many amplifiers. Though the frequency response may not be perfect, the transient response will beoutstanding. Remember, only your bass needs to be super loud. Everything else can be a simple designbecause you don't need the mids or highs to be too loud.Question:Is 80Hz the best cutoff frequency for bass bins? I heard some people talking about 125 Hz. The JBL 18"driver can handle between 30 and 800 Hz.Answer:80 Hz is good for L36 type cabinets. For W bins, a higher frequency is better. 100 or 125 Hz is probablygood. So, it depends on the type of cabinet. Also, if you do not have any 15"s or 18"s in your full rangecabinets, unfortunately you will need the bass bins to supply more midbass. The best way to find theexact frequency to use is just run the system and find the frequency that sounds the best overall. Notethat this may also depend on the venue. For example, If you have to do a small side room that has bad

acoustics, there may be some midbass resonant peaks in the room's frequency response. In this case, a125 Hz cutoff on the bins might be too high.Question:How does the dB/octave thing work? I understand that at a certain frequency the signal is cut, but why is24dB/octave too much. What exactly does that mean, that the cutoff is at 24dB/octave or 6dB/octave?Answer:

A capacitor or inductor by itself has a frequency cutoff rate of 6dB/octave. That means 6dB less signalwill get through one octave away. It's a long story, but the important thing is that you don't need anythinghigher than that for dance music, because percussion is what is important in dance music, not sharpcutoffs or high power handling.Question:I am currently in the process of putting together a small system for private venues. Based on theknowledge I have gathered so far, I have purchased four Cerwin-Vega T-36 bass bins and two Cerwin V-

253's. I am now looking into purchasing some Crest Professional amps to power them. What model(s)do you suggest?The next step will be to get the rest of the pieces. I know I need a leveler and some crossovers, but that'sall I know. I understand I should use an active crossover on the bass bins and minimal phase delaycrossovers for the full-range speakers. But what kind? Also what kind of cables should I be using tohook all this up? [...] I have a mixer but I'm looking into buying a new one.Answer:Start out with a good professional grade mixer, cartridges (higher-end Ortofon or Shure), and turntables(Technics 1200MK3 or high-end Vestax), and a limiter or leveler.The only other thing you will then need is a low pass filter or crossover for the bass bins. It should be setat 80 Hz frequency. Only use it for the bass bins, do not run the signal for the full-range cabinets throughit. Any inexpensive stereo crossover will do, just make sure it has XLR ins and outs (stay away fromanything with RCA jacks). And by the way 2 V-253s and 4 T-36s is an excellent choice of cabinets for

dance music.For amps, a Crest CA12 or 8001 would be good for the 2 V-253s. A Crest 9001 would be good for the 4T-36s. Stay away from any lower cost amps than the Crest Pro or CA series. Lower grade amps can cutout if overheated and the audio quality may not be as good.For cables, use 10 gauge cable if possible. 12 gauge cable is OK for short runs (less than 25 feet), butavoid it if possible. It does not matter what brand as long as it's thick, fine stranded, oxygen free cable.For signal cables, make sure the plugs are gold plated, and hold tightly, and that the cables look like theycan take some abuse. And always have some spare cables on hand in case one breaks.Question:


20/20

I have two questions: What do you think of active speakers in general and the Mackie SRM-450 inparticular? And do you have any advise for anyone wanting to learn about sound engineering and soundsystems?Answer:Regarding active speakers, their overall quality and cost-effectiveness are lower than what is availablewith passive speakers and the large number of high quality amplifiers available. Active speakers areeasier to transport and set up however, making them ideal for portable and rental applications. In thenext few years, better active products will become available and their cost effectiveness in smaller soundsystems will begin to approach that of passive speakers, making them a better alternative in almostall applications. Advances will also occur which will allow simple system management of all activecomponents via a single cable (carrying power and multitrack digital audio and control signals) chainedbetween any number of system components. Most pro systems will adopt this design over the next 10years or so.The Mackie SRM-450 is a good speaker for rental applications since it is so easy to transport and setup. It sounds decent and has a good output level, but in terms of sound quality it is definitely far behindsome passive alternatives at the same price. It is an ideal choice for a monitor if you are buying onlyone however, because the passive alternative is more cost effective only if you are getting two or morespeakers (since most pro amplifiers are stereo).

About learning the science of sound, the best place to start is with the web. There are 100's of websitesrelating to pro sound, and they have all the info you need. There are also messageboards such

as www.live-audio.com which are an excellent resource. If you want to go further than that, I wouldsuggest that you study engineering.

Free Festival ManualOhms, Amps and Speakers - the technical side of bass...

Add new comment
http://www.live-audio.com/http://bassbot.org/node/3404http://bassbot.org/node/3402http://bassbot.org/comment/reply/3403#comment-formhttp://bassbot.org/comment/reply/3403#comment-formhttp://bassbot.org/comment/reply/3403#comment-formhttp://bassbot.org/comment/reply/3403#comment-formhttp://bassbot.org/comment/reply/3403#comment-formhttp://bassbot.org/comment/reply/3403#comment-formhttp://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3402http://bassbot.org/node/3404http://bassbot.org/node/3404http://bassbot.org/node/3404http://bassbot.org/node/3404http://bassbot.org/node/3404http://bassbot.org/node/3404http://www.live-audio.com/ht

Sound for Underground Dance - The Technical Foundation.

Documents

Transcript of Sound for Underground Dance - The Technical Foundation.