SMARTBARK CONTROL COLLAR

USER MANUALThank you for choosing this Bark Control Collar! Please contact our customer service if you have any questions and we will help you.

SAFETY CAUTIONSDo not attempt to correct the behavior of dogs that are aggressive to people or other animals with this product. Aggressive dogs may associate training collar stimulation with other control stimulus and become more aggressive. Aggressive behavior should be corrected by a dog training specialist. If you are unsure of whether this product is appropriate for your dog,please consult your veterinarian or a certified trainer.The Bark Control Collar must only be used on healthy dogs. This collar is not intended for use on dogs weighing less than 6 lbs or under 6 months old. Take your dog to a veterinarian before use if he is not in good health.

12

PRODUCT INFORMATION

Notes:For your dog’s comfort and safety, please ensure the conductive probe covers are worn on stainless steel probes .

Please take them off when you need to test the static shock with the provided test light tool. Place the conductive probe covers on the probes before putting the Bark Control Collar on your dog. (The conductive probe covers can deliver the static shock !)

INDICATORS DEFINITION-Red Indicator Light Solid: Bark Control Collar is on Beep+Vibrate+Shock Mode. -Green Indicator Light Solid: Bark Control Collar is on Beep+Vibrate Mode. -Red/Green Indicator Light Flashing: Bark Control Collar is in working modes selection status.-Blue Indicator Light Solid: Bark Control Collar is on charge and fully charged.-Blue Indicator Light Flashing: Bark Control Collar battery is low, or it’s on charge but not fully charged.

POWER/SET BUTTON-Press this button for 1 second to power it on, Bark Control Collar vibrates, then red/green indicator light is solid, it means device is powered on successfully. -When device is powered on already, press this button to switch the sensitivity level. Level 1 to 5 can be adjusted, level 5 is the highest sensitivity level, and level 1 is the lowest.

DUAL WORKING MODES

Solid red indicator light indicates device is on Beep+Vibrate+Shock Mode.

Solid green indicator light indicates device is on Beep+Vibrate Mode.

SensitivityLevel Display

Beep+Vibrate+Shock Mode Indicator

Power/Set Button

Contact Point

Beep+Vibrate Mode Indicator

Charging Port(with cover)

Power Indicator

Conductive Probe Cover

Stainless Steel Probe

Sensor Mic

HOW TO SWITCH THE WORKING MODES?In the power off condition, press the Power/Set button for 3 seconds(device will be powered on and will vibrate in 1 second, keep pressing the button), till device beeps and red/green indicator light flashes, which means device is into working mode selection status. Press the Power/Set button to select the working mode , after 5 seconds the mode indicator light selected will stop flashing, and the working mode is set.

HOW TO TEST THE BARK CONTROL COLLAR?Select the Beep+Vibrate+Shock mode,and the red indicator light is solid.

Select the Beep+Vibrate mode, and the green indicator light is solid. Play a dog barking recording near the sensor mic. The device will beep, then vibrate.

HOW TO RETHREAD THE COLLAR?Follow the A-B-C-D steps instructed to thread the collar.

-Press this button for 3 seconds to power off, Bark Control Collar beeps and red/green indicator light is turned off. It means device is powered off successfully.

HOW TO USE THE BARK CONTROL COLLAR?1.Before use, please fully charge the Bark Control Collar via a power bank, your PC or a charger with 5V output voltage .Charger with output voltage over 5V may cause electric damage to the Bark Control Collar. Normally you can always see the output voltage information on the surface of the charger.It takes 2~3 hours to get the Bark Control Collar fully charged.

Play a dog barking recording near the sensor mic in the Bark Control Collar. (Notes: yelling,honking,knocking or blowing can’t trigger the device). Hold the test light tool to the contact points,and it will flash when Bark Control Collar is triggered by the barking and delivered static shock, and the test light will flash brighter at higher stimulation levels. Please refer to the illustration of Beep+Vibrate+Shock operation in Page 3, you can see in which operation steps device will deliver static shock.

A B C D

34

2.Press the Power/Set button for 1 second, device vibrates, then red/green indicator light is solid, it indicates device is powered on. The default working mode is Beep+Vibration+Shock with red indicator light on. Please follow instructions above if you want to switch to Beep+Vibrate mode.

3.Press the Power/Set button to adjust the sensitivity. There are total 5 sensitivity levels, level 1 is the lowest and level 5 is the highest. Higher sensitivity level is suggested for dogs with weak barking.4.Fit the Bark Control Collar to your dog.

HOW TO FIT THE BARK CONTROL COLLAR?The proper fit and placement of the collar is important for effective training. The contact points must have direct contact with your pet’s skin on the underside of the neck. To assure a proper fit, please follow these steps:-Make sure that the collar is turned off-Have your pet standing comfortably (3A)-Place the collar receiver on your pet’s neck close to the ears. Center the contact points underneath your pet’s neck to touch the skin (3B)-The collar should fit snugly. Yet loose enough to allow one finger to fit between the strap and your pet’s neck (3C)

HOW DOES THE BARK CONTROL COLLAR WORK?

Q: Why can’t the product work when it’s newly bought ?A: Please fully charge Bark Control Collar, and make sure the blue battery indicator light is solid during charge, then you can start to use the product.

Q: Why does the product not work when the dog is barking?A: Please ensure that the product is close to the dog's neck, and level up the sensitivity .

Q: Why can’t the product be charged when it is used for a period of time?A: Please change the USB cable or charger and try, and make sure the charger output voltage is 5V.

Q:Why is the product triggered sometimes in a noisy environment though the dog isn’t barking?A:Some stray environment noises may have similar frequency and intensity to the barking which may trigger the product. Please lower the sensitivity level.

Q:Will my dog stop barking completely?A:The Bark Control Collar effectively and humanely stops all barking when it is worn. It should only be worn during periods of unwanted barking.

Q:Is the Bark Control Collar safe and humane?A:Yes. The Bark Control Collar is designed to get your dog’s attention, not to punish him. However, the initial Static Correction may startle your dog.

1. Do not allow your dog to chew this collar. You should also try to minimize scratching or clawing the case. 2. This device is made up of plastic and electronic components that are not digestible. Consult your local vet if your dog swallowed any part of this product. 3. The collar is not intended for use as a restraining collar. If you are using a leash, use it with a separate restraining type of collar. 4. Although the Bark Control Collar's microprocessor is designed to differentiate your dog's individual bark from environmental noises, we cannot make sure all barking can 100% activate the device.

COMPONENTS-Bark Control Collar x1-Light Reflective Nylon Collar Strap x1-USB Cable x1-Stainless Steel Probes x2 pairs-Conductive Probe Covers x2 pairs-Test Light Tool x1-User Manual x1

Made in ChinaVersion:Q6-01

In Beep+Vibrate mode, the Bark Control Collar will beep for 3 seconds and then vibrate for 3 seconds every time it’s triggered.

In Beep+Vibrate+Shock mode, the operation steps are described at thepicturefrom the right side.

FREQUENTLY A SKED QUESTIONS

WAR N TIPS