Seminar on Renewable Energy Technology implementation in … · 2016. 11. 3. · Seminar on...
25
Seminar on Renewable Energy Technology implementation in Thailand Experience transfer from Europe co-organised by the Delegation of the European Union to Thailand and the Department of Alternative Energy Development and Efficiency, Ministry of Energy PV performance and the local industrial development Mr. Ruengrit Ninae Electrical and Electronic Products Testing Center (PTEC) 4 October 2012
Transcript of Seminar on Renewable Energy Technology implementation in … · 2016. 11. 3. · Seminar on...
Seminar on Renewable Energy Technology implementation in Thailand
Experience transfer from Europe
co-organised by the Delegation of the European Union to Thailand and
the Department of Alternative Energy Development and Efficiency, Ministry of Energy
PV performance and the local industrial development
Mr. Ruengrit Ninae Electrical and Electronic Products Testing Center (PTEC)
4 October 2012
Outline
• Introduction PTEC
• PV-module testing meet to local and
international standards
• PV-system characteristic verification
Outline
• Introduction PTEC
• PV-module testing meet to local and
international standards
• PV-system characteristic verification
Electrical and Electronic Products
Testing Center (PTEC)
National Science and Technology
Development Agency (NSTDA) Ministry of Science and Technology
>100 Laboratories included : EE, Telecom, Bio, material, Nano-technology,
1000 researcher included: 600 Ph.D 300 Master degree, 100Bachelors
Ministry of Science and Technology
Lab network of NSTDA
National Center
Introduction PTEC
History: Electrical and Electronic Products Testing Center (PTEC) was founded in 1994, under the co-operation of National Science and Technology Development Agency (NSTDA), National Electronics and Computer Technology Center (NECTEC) and also King Mongkut’s Institute of Technology Lardkrabang (KMITL).
• Objective PTEC objective will be, establishing the professional testing laboratory to service all local manufacturing, especially all exporter to upgrade their product to meet the international market and also enhance their competitiveness in global market.
Introduction PTEC
PTEC objective will be, establishing the professional testing laboratory to
service all local manufacturing, especially all exporter to upgrade their
product to meet the international market and also enhance their
competitiveness in global market.
Introduction PTEC
In 2012, PTEC have 14 services included; EMC testing, safety testing, Energy testing, Calibration, Survey, Telecom Testing, RFID Testing, Military Testing, Consultancy, Research & Development, Training, Automotive Testing and Project management.
Outline
• Organization introductions
• PV-module testing meet to local and
international standards
• PV-system characteristic verification
PV-module testing meet to local
and international standards
• Design qualification and type approval of
PV Module
– IEC 61215 (Crystalline type)
– TIS 1843 (Crystalline type)
– IEC 61646 (Thin-film type)
– TIS 2210 (Thin-film type)
• Safety qulification
– IEC 61730-1, IEC 61730-2
PV-module testing meet to local
and international standards
• Design qualification and type approval of
PV Module
– Performance Testing
– Environment Testing
– PV-Module Material Testing
– Outdoor Testing
– Mechanics Testing
PV-module testing meet to local
and international standards
• Performance Testing – Performance at
Standard Test Condition (STC)
– Performance at nominal Operating Cell Temperature (NOCT)
– Performance at low irradiance
– Measurement of temperature coefficient
PV-module testing meet to local
and international standards
• Environment Testing
– Thermal cycling test
– Humidity freeze test
– Damp heat test
PV-module testing meet to local
and international standards
• PV-Module Material
Testing
– Insulation Test
– Wet leakage current
– Hot-spot endurance
test
– UV preconditioning
test
– Light-soaking test
PV-module testing meet to local
and international standards
• Outdoor Testing – Measurement of
nominal Operating Cell
Temperature (NOCT)
– Outdoor exposure test
– Hot-sport endurance
test
PV-module testing meet to local
and international standards
• Mechanics Testing
– Mechanical load test
– Robustness of
termination test
– Hail test
Outline
• Organization introductions
• PV-module testing meet to local and
international standards
• PV-system characteristic verification
PV-system characteristic
verification
• Photovoltaic systems
– Measuring efficiency of power conditioners –
(IEC 61683)
– Performance monitoring - measurement, data
exchange and analysis (IEC 61724)
– PV array - On-site measurement of I-V
characteristics (IEC 61829)
– commissioning tests and inspection for Grid
connected photovoltaic systems (IEC 62446)
PV-system characteristic
verification
• Measurement of PV array I-V characteristic under actual on-site condition can provide • Data on power rating
• Verification of installed array power performance relative to design specifications;
• Detection of possible differences between on-site laboratory or factory measurements
• Detection of possible performance degradation of modules and arrays with respect to on-site initial data.
PV-system characteristic
verification
• Performance monitoring measurement, data exchange and analysis – monitoring of energy-
related photovoltaic (PV) system characteristics,
– For the exchange and analysis of monitored data.
– The purpose is the assessment of the overall performance of PV systems.
PV-system characteristic
verification
• Commissioning tests and inspection for Grid connected photovoltaic systems (IEC 62446)
– Defines the minimal information and documentation required to be handed over to a customer following
– The installation of a grid connected PV system. Also describes the minimum commissioning tests,
– Inspection criteria and documentation expected to verify the safe installation and correct operation of the system.
PV-system characteristic
verification
Future work of PTEC
(PV-inverter testing lab)
• PV systems - Characteristics of the utility interface
– IEC 61727: Photovoltaic (PV) systems - Characteristics of the utility interface
– IEC 62116: Test procedure of islanding prevention measures for utility-interconnected photovoltaic inverters
– IEC 62093: Balance-of-system components for photovoltaic systems - Design qualification natural environments
Grid-Connected PV Inverter Test Block Diagram
EMC Testing :Brochure
Products Safety Testing :Brochure
Calibration :Brochure
Solar Cell Testing :Brochure
Site Survey :Brochure
RFID Testing :Brochure
Telecom Testing :Brochure
Training / R&D :Brochure
Consultancy :Brochure
•Energy Saving/ Efficiency Testing
Website: WWW. ptec.or.th
Tel: 0-273 92195-98 Ext: 111
Fax:0-273 92199
Email: [email protected]
For Further information
-please refer to:
Thank You Very Much
