RIDE-ON SWING CAR

Model no: 8821 | Batch no: PR3767

Please read and retain these instructions for future reference.

The illustrations used in this manual are to illustrate the operation method and structure of the product. Where there is a small difference between the physical item and the illustrations, please take the physical as the standard.

FEATURES:

Safe & stable

Low centre of gravity

Durable material

Indoor or outdoor play

No batteries, gears or pedals

HOW IT WORKS:

1. Place the ride on swing car onto a smooth, flat surface. 2. Sit with the feet on the footrests. Lean slightly forward and grip the steering wheel. 3. To propel the car forward, turn the steering wheel back and forth continuously. To go in reverse,

rotate the steering wheel 180 degrees. 4. To bring the ride on swing car to a stop, stop turning the wheel, wait for the car to slow, and

come to a stop.

SAFETY INFO:

1. When unpacking the ride on swing car, properly dispose of all plastic wrappings. 2. Adult supervision is required at all times. 3. Failure to follow the instructions may affect the safety of children. 4. This product is designed for use by children from 3 years to 6 years of age. 5. Protective equipment such as a helmet is recommended (protective equipment is not included). 6. Assembly must be completed by an adult. 7. Each time before use, ensure that all removeable parts and fasteners are firmly in place. 8. Only one child can use this at a time. 9. A child who is riding is not to be pushed. 10. Do not allow a child to stand on the ride-on. 11. Do not let children ride in the street, anywhere dangerous including stairs, doorsteps, steep

slopes, streets/roads, vehicle traffic, next to bodies of water and away from other obstacles. Use during day light hours or in an illuminated area is advised to avoid accidents in the dark.

12. Do not drive on long or wet grass, mud, soft ground, gravel or sand. 13. It is not recommended for use on wooden floors. The wheels may damage some floors. 14. The maximum carrying capacity is 30kg.

ASSEMBLY:

Included parts:

1. Body 2. Steering wheel assembly 3. Front wheel assembly with foam sheath 4. Rear right wheel (A), Rear left wheel (B) 5. Steering wheel cap

Tools required (not included): rubber mallet, 20mm socket wrench.

Steps:

Fit the notch on each wheel housing into the body. Push the wheels in at a 45 degree angle. When installed correctly, the rear wheel flare out from the body.

Warning: The rear wheel housing can not be removed once locked into place.

Strike the rear wheels with a rubber mallet (not included) to secure them in place.

Remove the foam sheath from the front wheel assembly.

Guide the front wheel shaft through the body, into the foam sheath, and through the hole at the top of the body.

Ensure it is inserted as far as it will go; it must be flush with the body. Wiggle into place if necessary.

Strike the base of the front wheel assembly with a rubber mallet.

The metal bearing should be seated securely in the body.

Fit the steering wheel into the top of the front wheel assembly.

Ensure that the bolt is attached to the steering wheel as shown.

Align the steering wheel with the smaller front wheels, so that the wide end of the steering wheel faces forward.

Note: When the front wheels are assembled and resting on a flat surface, the smaller front wheels do not contact the ground.

Use a 20mm socket wrench (not included) to tighten the nut in the steering wheel column AS TIGHT AS POSSIBLE. Fit the wrench onto the nut and turn until very tight.

Push the cap into the steering wheel.

TROUBLESHOOTING:

The rear wheels may detach from their housing if the ride on swing car is subjected to overloading or impact. Fit the wheel into their housing so that the flat sides of the white clips contact the wheel housing. Snap the wheel back into place.

If the steering wheel becomes locked or fails to propel the ride on swing car, the steering nut may not have been tightened enough during assembly. Remove the cap from the steering wheel with a screwdriver (not included) and loosen the nut with the socket wrench. Repeat steps 7 and 8, securing the nut as tightly as possible. Then add the steering wheel cap.