Revolve

12
Engineering 1182 College of Engineering Engineering Education Innovation Center Revolve Rev: 20120817, AJP Revolve 1

description

Revolve. 3D Shapes. Basic methods of creating 3D shapes using a 2D sketch: Extruding “Stretching” the shape from its original 2D outline to a 3 rd Dimension Revolving Creating a 3D object by drawing a 2D cross-section and revolving that around an axis. Revolving. 2D Profile Extents - PowerPoint PPT Presentation

Transcript of Revolve

Page 1: Revolve

• Engineering 1182

Revolve 1

College of EngineeringEngineering Education Innovation Center

Revolve

Rev: 20120817, AJP

Page 2: Revolve

• Engineering 1182

Revolve 2

3D ShapesBasic methods of creating 3D shapes using a 2D sketch:

1. Extruding• “Stretching” the shape from

its original 2D outline to a 3rd Dimension

2. Revolving• Creating a 3D object by

drawing a 2D cross-section and revolving that around an axis

Rev: 20120817, AJP

Page 3: Revolve

• Engineering 1182

Revolve 3

Revolving• 2D Profile• Extents

• Full Rotation• Degree

• Axis of Rotation:• Attached

– Closed Solid• Separated

– Solid with Hole

Rev: 20120817, AJP

Page 4: Revolve

• Engineering 1182

Revolve 4

Revolve Vs. Extrude• Revolve

Complements Extrusion

• Some Objects Difficult to Extrude

• i.e. Cones, wheels• How would you

create this object with extrude?

Rev: 20120817, AJP

Page 5: Revolve

• Engineering 1182

Revolve 5

Positive Revolves Negative Revolves

Rev: 20120817, AJP

Page 6: Revolve

• Engineering 1182

Revolve 6

Acceptable Profiles

Rev: 20120817, AJP

Page 7: Revolve

• Engineering 1182

Revolve 7Rev: 20120817, AJP

Options in the Line tool can be chosen to create a

construction line that will be used as a revolution axis

SolidWorks: Revolution Axis

Page 8: Revolve

• Engineering 1182

Revolve 8Rev: 20120817, AJP

SolidWorks: Closed Profile

Example of a closed profile aligned with the center axis (created by

using a construction line)

SolidWorks preview allows the designer to

select the correct options

Page 9: Revolve

• Engineering 1182

Revolve 9Rev: 20120817, AJP

SolidWorks: Hollow Profile

Example of a closed profile separated from the

center axis (created by using a construction line)

This example shows how to create a hollow revolve.

This is helpful in the creation of wheels, etc.

Page 10: Revolve

• Engineering 1182

Revolve

Revolves Wrap Up• Positive Revolve

– Make a 3D object• Negative Revolve

– Remove material from a 3D object• Attached Rotation

– Will produce a closed object• Separated Rotation

– Will produce an object with a hole– Use construction lines for axes– Ensure validity of profile (entire

sketch is on one side of revolution axis)

Homework AssignmentCreate the following shape. Focus on shape and proportionality, not dimensions.

Rev: 20140129, RCB 10

On which plane should you start you sketch? Why?

But how do you construct this area? Next slide

Fillets Tool

Page 11: Revolve

• Engineering 1182

Revolve

A Suggestion

Rev: 20140129, RCB 11

Draw vertical line

Draw center-point circle intersecting end of line

Draw vertical line intersecting edge of circle

Use “Trim Entries/Trim to closet”

Trim 180 degree arc

Trim 90 degree arc

Page 12: Revolve

• Engineering 1182

Revolve 12Rev: 20120817, AJP

Draw this wheel using the closed 2D profile

shown (from Problem 6.4 (n))

In-Class Assignment

On which plane should you start you sketch? Why?