Research Article OTRA Based Voltage Mode Third Order ...involving OTRA and OTRA and ( ) is feedback...
Transcript of Research Article OTRA Based Voltage Mode Third Order ...involving OTRA and OTRA and ( ) is feedback...
Research ArticleOTRA Based Voltage Mode Third Order Quadrature Oscillator
Rajeshwari Pandey,1 Neeta Pandey,1 Gurumurthy Komanapalli,1 and Rashika Anurag2
1 Department of Electronics and Communication Engineering, Delhi Technological University, Delhi 110042, India2Department of Electronics and Communication Engineering, JSS Academy of Technical Education, C-20/1 Sector 62,NOI DA, Uttar Pradesh 201301, India
Correspondence should be addressed to Neeta Pandey; [email protected]
Received 2 February 2014; Accepted 9 March 2014; Published 29 April 2014
Academic Editors: S. Gift, R. Senani, and E. Tlelo-Cuautle
Copyright ยฉ 2014 Rajeshwari Pandey et al. This is an open access article distributed under the Creative Commons AttributionLicense, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properlycited.
Two topologies of operational transresistance (OTRA) based third order quadrature oscillators (QO) are proposed in this paper.Theproposed oscillators are designed using a combination of lossy and lossless integrators. The proposed topologies can be made fullyintegrated by implementing the resistors usingmatched transistors operating in linear region,which also facilitates electronic tuningof oscillation frequency. The nonideality analysis of the circuit is also given and for high frequency applications self-compensationcan be used. Workability of the proposed QOs is verified through PSPICE simulations using 0.5 ๐m AGILENT CMOS processparameters. The total harmonic distortion (THD) for both the QO designs is found to be less than 1%.
1. Introduction
Quadrature oscillators (QO) produce outputs having a phasedifference of 90โ. The phase-locked sine-cosine relationshipof QO has useful applications in the field of telecommu-nications where the modulation scheme utilizes both in-phase and quadrature components, such as single-sidebandgenerators and quadrature mixers [1]. The QOs are alsoused extensively in the field of instrumentation and powerelectronics [2]. For these applications low value of total har-monic distortion (THD) is an essential requirement as higherharmonics have detrimental effects on electrical equipment.These higher order harmonics can also interfere with com-munication transmission lines since they oscillate at the samefrequencies as the transmit frequency. If left unchecked,increased temperature and interference can greatly shortenthe life of electronic equipment and cause damage to powersystems.
It is well known that higher order networks as comparedto lower order circuits provide better accuracy, frequencyresponse, and distortion performance [3, 4]. However, ithas been observed that higher order QO designs have notbeen explored much, as only a few third order QOs [1, 3โ16] have appeared in literature in recent years. A careful
observation suggests that the reported QO designs are basedon forming closed loop using (i) two lossy and one losslessintegrators [3โ5], (ii) one lossy and two lossless integrators[8], (iii) a second order low pass filter followed by anintegrator [1, 6, 7, 10โ16], and (iv) three low pass filters andgained feedback around the loop [9]. These topologies aredesigned using second generation current conveyor (CCII) [1,6], second generation current-controlled conveyor (CCCII)[7โ9], differential voltage current conveyor (DVCC) [10],op-amp [5], operational transconductance amplifier (OTA)[3], current difference transconductance amplifier (CDTA)[4, 11], operational transresistance amplifier (OTRA) [12],and current-controlled current difference transconductanceamplifier (CCCDTA) [13].The structure proposed in [15] usesdifferential difference current conveyor (DDCC) and OTAwhereas design of [16] is based on CCCDTA and OTA.
The OTRA is a current input voltage output device [17].Being a current processing block, it inherits all the advantagesof current mode techniques [12] and provides voltage outputat low impedance which can readily be used to drive volt-age input circuits without increasing component count. Anextensive literature review suggests though a large numberof OTRA based second order QOs [17โ21] are available inliterature, yet only a single third order QO topology using
Hindawi Publishing CorporationISRN ElectronicsVolume 2014, Article ID 126471, 5 pageshttp://dx.doi.org/10.1155/2014/126471
2 ISRN Electronics
Vp
VO
Ip
In
Vn IO
p
n
Figure 1: OTRA circuit symbol.
OTRA [12] is reported. This QO design is based on forminga closed loop using a second order low pass filter followed byan integrator.
In this paper two topologies of third order QO basedon OTRA have been presented which use the scheme oflossy and lossless integrators. One of the proposed circuitsmakes use of one inverting lossy and two lossless integratorsconnected in a feedback forming closed loop whereas theother configuration uses one lossless and two lossy integratorsto form closed loop. The proposed structures can be madefully integrated by implementing the resistors using matchedtransistors operating in linear region and can be tunedelectronically.
2. Circuit Description
The OTRA is a high gain, current input voltage outputanalog building block [17]. The input terminals of OTRAare internally grounded, thereby eliminating response lim-itations due to parasitic capacitances and resistances andhence is a suitable choice for high frequency applications.Thecircuit symbol of OTRA is shown in Figure 1 and the portcharacteristics are given by (1), where ๐
๐is transresistance
gain of OTRA:
[
[
๐๐
๐๐
๐๐
]
]
= [
[
0 0 0
0 0 0
๐ ๐
โ๐ ๐
0
]
]
[
[
๐ผ๐
๐ผ๐
๐ผ๐
]
]
. (1)
For ideal operations the ๐ ๐of OTRA approaches infinity
and forces the input currents to be equal. Thus OTRA mustbe used in a negative feedback configuration [22].
2.1. Circuit I. The first QO topology is shown in Figure 2. Ituses two lossless integrators and a lossy inverting integratorin the feedback forming a closed loop resulting in loop gainof the system as ๐ด(๐ )๐ฝ(๐ ), where ๐ด(๐ ) is forward path gaininvolving OTRA2 and OTRA3 and ๐ฝ(๐ ) is feedback gaininvolving OTRA1.
The criterion for oscillations [23] to occur is given by
1 โ ๐ด (๐ ) ๐ฝ (๐ ) = 0. (2)
If this criterion is satisfied, the closed loop system will resultin two quadrature phase oscillations, available at nodes 1 and2. Routine analysis of the circuit of Figure 2 results in thefollowing characteristic equation:
๐ 3
๐1๐2๐3๐ 2๐ 3+
๐ 2
๐ถ2๐ถ3๐ 2๐ 3
๐ 4
+ ๐ ๐3
๐ 3
๐ 5
+1
๐ 1
= 0. (3)
C3C2
C1
R5
R1
R2
R4
p
np
n
p
n
R3
1
2
3 V2V1
Figure 2: Proposed Circuit I.
C1
C3
C2
R1
R3
R2
R5
R4
n
p
n
p
n
p
2
1
3V1
V2
Figure 3: Proposed Circuit II.
From this characteristic equation the condition of oscillation(CO) and frequency of oscillation (FO) can be found to beFO:
๐ =1
2๐โ
1
๐ถ1๐ถ2๐ 2๐ 5
, (4)
CO:
๐ 4๐ 5= ๐ 1๐ 3. (5)
The FO can be adjusted to desired value through ๐ 2and
proper selection of resistors ๐ 1, ๐ 3, and ๐
4would satisfy the
CO.
2.2. Circuit II. The second proposed QO configuration isshown in Figure 3 which makes use of two lossy and onelossless integrators, all in inverting mode.
ISRN Electronics 3
Vb
Va
n
Vin
p
Figure 4: The MOS based resistor [17].
The characteristic equation of the Circuit II can bededuced as
๐ 3
๐ถ1๐ถ2๐ถ3๐ 3+ ๐ 2
(๐ถ2๐ถ3๐ 3
๐ 4
+๐ถ1๐ถ3๐ 3
๐ 5
) +๐ ๐ถ3๐ 3
๐ 4๐ 5
+1
๐ 1๐ 2
= 0,
(6)
FO:
๐ =1
2๐โ
1
๐ถ1๐ถ2๐ 4๐ 5
, (7)
CO:
๐ 1๐ 2๐ 3๐ถ3[๐ 4๐ถ1+ ๐ 5๐ถ2] = ๐ 2
4
๐ 2
5
๐ถ1๐ถ2. (8)
By suitable selection of ๐ 4and ๐
5the FO can be adjusted to
desired value and proper selection of resistors ๐ 1, ๐ 2, and ๐
3
results in desired CO.The current differencing property of the OTRA makes it
possible to implement the resistors connected to the inputterminals of OTRA, using MOS transistors with completenonlinearity cancellation [17]. Each resistor requires twomatched n-MOSFETs connected in a manner as shown inFigure 4 which represents a typical MOS implementation ofresistance connected at negative input of OTRA.
Symbols โ๐โ and โ๐โ represent the noninverting and theinverting terminals of the OTRA. As can be seen from thefigure, the voltages at the drain and the source terminals forboth MOSFETs are equal. On taking the difference of thecurrents flowing in the two transistors, the nonlinearity getscancelled out. The resistor value realized can be expressed as
๐ =1
๐พ๐(๐๐โ ๐๐), (9)
where
๐พ๐
= ๐๐ถ๐๐
๐
๐ฟ. (10)
๐พ๐
needs to be determined for the transistors being usedto implement the resistors and ๐, ๐ถ
๐๐, and ๐/๐ฟ represent
standard transistor parameters. The MOS based implemen-tations of Circuit I and Circuit II are shown in Figures 5 and6, respectively.
n
p
n
p
n
p
1
2
3
Va2
Vb2
Vb3
Va3
Vb4
Va4 Va5
Va1
Vb1
Vb5
C2 C3
C1
Figure 5: The MOS based implementation of QO Circuit I.
C3
C1 C2
n
p2
n
p3
n
p1
Va2
Va4
Va1
Vb1Vb4
Va3
Vb3
Vb5
Vb2
Va5
Figure 6: The MOS based implementation of QO Circuit II.
3. Nonideal Analysis
The output of the QO may deviate due to nonideality ofOTRA in practice. Ideally the transresistance gain ๐
๐is
assumed to approach infinity. However, practically ๐ ๐is a
frequency dependent finite value. Considering a single polemodel for the transresistance gain, ๐
๐can be expressed as
๐ ๐(๐ ) = (
๐ 0
1 + (๐ /๐0)) , (11)
where ๐ 0is dc transresistance gain. For high frequency
applications the transresistance gain ๐ ๐(๐ ) reduces to
๐ ๐(๐ ) = (
1
๐ ๐ถ๐
) , (12)
4 ISRN Electronics
VB
Vo
M8
M1
M12
M2 M3
M13
M5M4 M6 M7
M14
M11M9 M10
IB
In Ip
VDD
VSS
Figure 7: CMOS OTRA [22].
where
๐ถ๐=
1
๐ 0๐0
. (13)
Taking this effect into account (3) modifies to
๐ 3
(๐1+ ๐๐) (๐2+ ๐๐) (๐3+ ๐๐) ๐ 2๐ 3
+ ๐ 2
(๐2+ ๐๐) (๐3+ ๐๐)
๐ 2๐ 3
๐ 4
+ ๐ (๐3+ ๐๐)๐ 3
๐ 5
+1
๐ 1
= 0.
(14)
From (14) it is found that FO for Circuit I changes to
๐ =1
2๐โ
1
(๐ถ1+ ๐ถ๐) (๐ถ2+ ๐ถ๐) ๐ 2๐ 5
. (15)
Due to nonideality effect of OTRA (6) changes to
๐ 3
(๐1+ ๐๐) (๐2+ ๐๐) (๐3+ ๐๐) ๐ 3
+ ๐ 2
((๐2+ ๐๐) (๐3+ ๐๐)๐ 3
๐ 4
+ (๐1+ ๐๐) (๐3+ ๐๐)๐ 3
๐ 5
)
+ ๐ (๐3+ ๐๐)
๐ 3
๐ 4๐ 5
+1
๐ 1๐ 2
= 0.
(16)
The characteristic equation represented by (16) results inmodified FO for Circuit II and is expressed as
๐ =1
2๐โ
1
(๐ถ1+ ๐ถ๐) (๐ถ2+ ๐ถ๐) ๐ 4๐ 5
. (17)
The effect of ๐ถ๐can be eliminated by preadjusting the
values of capacitors ๐ถ1, ๐ถ2, and ๐ถ
3, thus achieving self-
compensation.
20 22 24 26 28 30 32 34 36 38 40 42 44โ200
โ100
0
100
200
V1
V1
,V2
(mV
)
Time (๐s)
V2
V(V1)
V(V2)
Figure 8: Transient output of proposed QO Circuit I.
Frequency
100
120
140
160
180
200
220
240
250
0
50
100
140
V1,V
2(m
V)
V(V1)
V(V2)
Figure 9: Frequency spectrum of output of QO Circuit I.
4. Simulation Results
The proposed QO is verified through simulations using theCMOS implementation of the OTRA [22] which is shown inFigure 7. The SPICE simulations are performed using 0.5 ๐mCMOS process parameters provided by MOSIS (AGILENT).Supply voltages taken are ยฑ1.5V. Both the QO topologiesare designed for an FO of 159KHz and the simulated valuewas observed to be 161 KHz for Circuits I and II, respectively.The simulated transient output and corresponding frequencyspectrum for Circuit I are shown in Figures 8 and 9,respectively, and those for Circuit II are depicted in Figures10 and 11. The percentage total harmonic distortion (THD) is0.57% forQOCircuit I and that for Circuit II is observed to be0.7%.These values are considerably low as compared to 6.3%THD of QO circuit of [12].
5. Conclusion
Two topologies of third order OTRA based quadratureoscillator are presented in this paper using lossy and losslessintegrators.The simulations are performed using PSPICE andit is observed that the results are in close agreement withtheoretical propositioned. The simulated value of % THDin both the circuits is quite low as compared to other thirdorder structures available in literature. The effect of nonidealbehavior of OTRA and high frequency compensation schemehas also been included in the proposed theory.
ISRN Electronics 5
20 22 24 26 28 30 32 34 36 38 40 42 44300
400
500
600
700
Time
V1,V
2(m
V) V1 V2
V(V1)
V(V2)
Figure 10: Transient output of proposed QO Circuit II.
Frequency
100
120
140
160
180
200
220
240
250
50
0
100
150
V1,V
2(m
V)
V(V1)
V(V2)
Figure 11: Frequency spectrum of output of QO Circuit II.
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper.
References
[1] J.-W. Horng, C.-L. Hou, C.-M. Chang, W.-Y. Chung, H.-W.Tang, and Y.-H. Wen, โQuadrature oscillators using CCIIs,โInternational Journal of Electronics, vol. 92, no. 1, pp. 21โ31, 2005.
[2] J.-W. Horng, C.-L. Hou, C.-M. Chang, H.-P. Chou, C.-T.Lin, and Y.-H. Wen, โQuadrature oscillators with groundedcapacitors and resistors using FDCCIIs,โ ETRI Journal, vol. 28,no. 4, pp. 486โ493, 2006.
[3] P. Prommee and K. Dejhan, โAn integrable electronic-controlled quadrature sinusoidal oscillator using CMOSoperational transconductance amplifier,โ International Journalof Electronics, vol. 89, no. 5, pp. 365โ379, 2002.
[4] J.-W. Horng, โCurrent-mode third-order quadrature oscillatorusing CDTAs,โ Active and Passive Electronic Components, vol.2009, Article ID 789171, 5 pages, 2009.
[5] J.-W. Horng, โQuadrature oscillators using operational ampli-fiers,โ Active and Passive Electronic Components, vol. 2011,Article ID 320367, 2011.
[6] J.-W. Horng, โCurrent/voltage-mode third order quadratureoscillator employing two multiple outputs CCIIs and groundedcapacitors,โ Indian Journal of Pure and Applied Physics, vol. 49,no. 7, pp. 494โ498, 2011.
[7] S. Maheshwari and I. A. Khan, โCurrent controlled third orderquadrature oscillator,โ IEE ProceedingsโCircuits Devices andSystems, vol. 152, pp. 605โ607, 2005.
[8] S. Maheshwari and I. A. Khan, โCurrent-mode third-orderquadrature oscillator,โ IET Circuits, Devices and Systems, vol. 4,no. 3, pp. 188โ195, 2010.
[9] S.Maheshwari and R. Verma, โElectronically tunable sinusoidaloscillator circuit,โActive and Passive Electronic Components, vol.2012, Article ID 719376, 6 pages, 2012.
[10] S. Maheshwari, โAnalogue signal processing applications usinga new circuit topology,โ IET Circuits, Devices and Systems, vol.3, no. 3, pp. 106โ115, 2009.
[11] J.-W. Horng, H. Lee, and J.-Y.Wu, โElectronically tunable third-order quadrature oscillator using CDTAs,โ Radioengineering,vol. 19, no. 2, pp. 326โ330, 2010.
[12] R. Pandey, N. Pandey, and S. K. Paul, โMOS-C third orderquadrature oscillator using OTRA,โ in Proceedings of the 3rdInternational Conference on Computer and CommunicationTechnology, pp. 77โ80, November 2012.
[13] S. Lawanwisut and M. Siripruchyanun, โHigh output-impedance current-mode third-order quadrature oscillatorbased on CCCCTAs,โ in Proceedings of the IEEE Region 10Conference (TENCON โ09), pp. 1โ4, November 2009.
[14] A. Kwawsibsam, B. Sreewirote, and W. Jaikla, โThird-ordervoltage-mode quadratrue oscillator using DDCC andOTAs,โ inInternational Conference on Circuits, System and Simulation, pp.317โ321, 2011.
[15] M. Kumngern and S. Junnapiya, โCurrent-mode third-orderquadrature oscillator using minimum elements,โ in Proceedingsof the International Conference on Electrical Engineering andInformatics (ICEEI โ11), pp. 1โ4, July 2011.
[16] D. Duangmalai and W. Jaikla, โRealization of current-modequadrature oscillator based on third order technique,โ ACEEEInternational Journal on Electrical and Power Engineering, vol.2, pp. 46โ49, 2011.
[17] K. N. Salama and A. M. Soliman, โCMOS operational transre-sistance amplifier for analog signal processing,โMicroelectronicsJournal, vol. 30, no. 3, pp. 235โ245, 1999.
[18] K. N. Salama and A. M. Soliman, โUniversal filters using Oper-ational Transresistance Amplifiers,โ AEU-Archiv fur Elektronikund Ubertragungstechnik, vol. 53, no. 1, pp. 49โ52, 1999.
[19] S. Kilinc and U. Cam, โOperational transresistance amplifierbased first-order allpass filter with an application example,โ inProceedings of the 47th Midwest Symposium on Circuits andSystems, vol. 1, pp. 65โ68, July 2004.
[20] S. Kilinc and U. Cam, โCascadable allpass and notch filtersemploying single operational transresistance amplifier,โ Com-puters and Electrical Engineering, vol. 31, no. 6, pp. 391โ401,2005.
[21] C. Cakir, U. Cam, and O. Cicekoglu, โNovel allpass filterconfiguration employing single OTRA,โ IEEE Transactions onCircuits and Systems II: Express Briefs, vol. 52, no. 3, pp. 122โ125,2005.
[22] H. Mostafa and A. M. Soliman, โA modified CMOS realizationof the operational transresistance amplifier (OTRA),โ Frequenz,vol. 60, no. 3-4, pp. 70โ76, 2006.
[23] A. S. Sedra and K. C. Smith, Microelectronic Circuits., OxfordUniversity Press, New York, NY, USA, 2004.
International Journal of
AerospaceEngineeringHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
RoboticsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Active and Passive Electronic Components
Control Scienceand Engineering
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
RotatingMachinery
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporation http://www.hindawi.com
Journal ofEngineeringVolume 2014
Submit your manuscripts athttp://www.hindawi.com
VLSI Design
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Shock and Vibration
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Civil EngineeringAdvances in
Acoustics and VibrationAdvances in
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Electrical and Computer Engineering
Journal of
Advances inOptoElectronics
Hindawi Publishing Corporation http://www.hindawi.com
Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
SensorsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Modelling & Simulation in EngineeringHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Chemical EngineeringInternational Journal of Antennas and
Propagation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Navigation and Observation
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
DistributedSensor Networks
International Journal of