RENEWABLE ENERGY (WIND POWER) MINI PROTOTYPE PLANT...
Transcript of RENEWABLE ENERGY (WIND POWER) MINI PROTOTYPE PLANT...
RENEWABLE ENERGY (WIND POWER) MINI PROTOTYPE
PLANT WITH SCADA SYSTEM
Ahmad Suzaimy Bin Sukor
Bachelor of Industrial Power Engineering
May 2010
“I hereby declare that I have read through this report entitled “Renewable Energy (Wind Power) Mini Prototype Plant With SCADA System” and found that it has comply the partial fulfillment for awarding the degree of Bachelor of Electrical Engineering (Industrial Power)”
Signature : ……………………………………………………
Supervisor’s Name : MR. MASLAN BIN ZAINON
Date : 12th MAY 2010
RENEWABLE ENERGY (WIND POWER) MINI PROTOTYPE PLANT
WITH SCADA SYSTEM
AHMAD SUZAIMY BIN SUKOR
A report submitted in partial fulfillment of the requirements for the degree of Bachelor of Electrical Engineering (Industrial Power)
Faculty of Electrical Engineering UNIVERSITI TEKNIKAL MALAYSIA MELAKA
2010
I declare that this report entitle “Renewable Energy (Wind Power) Mini Prototype Plant With SCADA System” is the result of my own research except as cited in the references. The report has not been accepted for any degree and is not concurrently submitted in candidature of any other degree.
Signature : ……………………………………………..
Name : AHMAD SUZAIMY BIN SUKOR
Date : 12th MAY 2010
To my beloved mother and father
ACKNOWLDGEMENT
Firstly, I would like to express my special thanks to my supervisor, En. Maslan Bin
Zainon, for his avail advices, commitment and also continual guidance for help me
implementing my study and research about my project during a FYP. The knowledge’s and
ideas that he gave to me are very useful for me to implement project research
appropriately.
I also want to deliver my grateful for the cooperation and assistance provided by all
friends that under same supervisor with me. I very appreciated for all their assistances.
Finally do not forget, my FYP would not be carried out smoothly without the supports and
encouragements from my parents. I would like to express my sincere gratitude to all of them
especially for their help during the time in need.
Thank you.
ABSTRACT
This FYP report presents the purpose of research about the application of
renewable energy as alternative energy to generate electricity. The motive of this project is
to analysis the usage and advantages of renewable energy to replace fossil fuel as the
energy to generate electricity. This project uses wind as the energy to rotate a wind turbine
for this mini prototype plant to generate electricity. Wind energy is use to rotate the wind
turbine system which will convert mechanical energy produce from a rotor rotation to
electrical energy. The electrical energy generate from wind turbine system were supply to
an inverter circuit. This inverter circuit will convert the electricity produce from wind
turbine system as require whether AC or DC. SCADA system ensures this mini prototype
plant operation fluent and very well. The functions of SCADA system are monitor and
control this plant operation.
ABSTRAK
Laporan FYP ini membentangkan tujuan kajian berkenaan aplikasi sumber tenaga
yang boleh diperbaharui sebagai tenaga alternatif yang boleh digunakan untuk menjana
tenaga elektrik. Matlamat projek ini adalah untuk melakukan analisis berkenaan
penggunaan dan kelebihan-kelebihan sumber tenaga yang boleh diperbaharui untuk
menggantikan sumber tenaga fosil untuk menjana tenaga elektrik. Projek ini menggunakan
angin sebagai sumber tenaga untuk menjana elektrik bagi prototaip loji janakuasa mini
yang ingin dibangunkan. Tenaga angin digunakan untuk memutar sistem turbin angin di
mana ia akan menukarkan tenaga mekanikal yang dihasilkan oleh putaran rotor kepada
tenaga elektrik. Tenaga elektrik yang dijana oleh sistem turbin angin akan dibekalkan terus
ke litar inverter. Litar inverter ini, akan mengubah jenis tenaga elektrik yang telah dijana
oleh sistem turbin angin kepada jenis tenaga elektrik yang dikehendaki samada AC atau
DC. Untuk memastikan projek ini beroperasi dengan sempurna, prototaip loji janakuasa
mini ini juga dilengkapi dengan sistem SCADA. Sistem SCADA ini akan berfungsi
sebagai sistem kawalan dan pengawasan untuk pengoperasian loji ini.
TABLE OF CONTENTS
CHAPTER TITLE PAGE
ACKOWLDGEMENT ii
ABSTRACT iii
ABSTRAK iv
TABLE OF CONTENTS v
LIST OF TABLES viii
LIST OF FIGURES ix
LIST OF SYMBOLS xi
LIST OF ABBREVIATION xii
LIST OF APPENDICES xiii
1 INTRODUCTION 1
1.1 Overview of Project Background 1
1.1.1 Wind Energy 1
1.2 Problem Statement 3
1.3 Project Objectives 3
1.4 Project Scope 3
1.5 Thesis Outline 4
2 LITERATURE REVIEW AND 5
THEORETICAL BACKGROUND
2.1 Introduction 5
2.2 Wind Turbines 5
2.2.1 Wind Turbine System Steps 7
of Installations Amongst Industrial
and Domestic
2.2.2 The Differences of Wind Turbine 8
System Amongst The Applications
of Industrial, Domestic, and
Educational.
2.3 Wind Turbine System Speed and 9
Energy Calculations
2.4 Power Electronic Circuit (Inverter) 11
2.5 Programmable Logic Controller (PLC) 11
2.6 SCADA System 12
2.7 Develop the SCADA System of a Wind 13
Energy Mini Prototype Plant
2.7.1 Teaching and Learning Purposes 13
3 METHODOLOGY 14
3.1 Introduction 14
3.2 Basic Structure of a Renewable Energy 16
(Wind) Mini Prototype Plant with
SCADA System
3.3 Design of an Inverter Circuit 16
3.4 Design of Wind Turbine Platform and 17
Base
3.5 Simulation Circuit Test 19
3.5.1 Simulation Use Multisim 19
3.5.2 Simulation Use Breadboard 21
3.6 Development of PLC and SCADA 22
System
3.7 Data Analysis 25
3.7.1 Outline of Project 26
4 RESULT AND DISCUSSION 28
4.1 Software Result 28
4.1.1 SCADA (CX – Designer) 28
4.1.2 Ladder Diagram 30
4.1.3 SCADA System Combine With 32
Ladder Diagram Simulate Used
CX - Simulator
4.2 Hardware Result 33
4.2.1 Experiment A (Wind turbine 33
system rotated by using table
fan)
4.2.2 Experiment B (Wind turbine 34
system rotated by different
car speed)
4.3 Discussion 36
5 CONCLUSION 38
5.1 Conclusion 38
5.2 Recommendation of Future Works 38
REFERENCES 39
APPENDICES 41
LIST OF TABLE
TABLE TITLE PAGE
2.1 The differences of wind turbines system amongst the 8
applications of industrial, domestic, and educational.
3.5 Preliminary result for the simulation experiment 22
3.6 List of Input Address 23
3.6.1 List of Output Address 23
4.1 The result for Experiment A 33
4.2 The value of output voltage (Vac) according the car 34
speeds
4.2.1 The value of output voltage (Vdc), output current (Idc), 35
and power produced according to car speeds
LIST OF FIGURES
FIGURE TITLE PAGE
2.1 Horizontal axis wind turbines 6
2.2 Vertical axis wind turbines 7
3.1 Project Workflows 15
3.2 Schematic block diagram of a renewable energy (wind) 16
mini prototype plant with SCADA system
3.3 Schematic diagram of 12Vdc to 120Vac inverter 17
circuit
3.4 Side view of wind turbine platform and base with part 18
range value
3.4.1 A complete wind turbine platform and base 18
3.4.2 Wind turbine blades 18
3.5 Design and simulation of an inverter circuit flow 19
3.5.1 The simulation result for output voltage value produced 20
by a (12Vdc – 120 Vac) inverter circuit
3.5.2 The simulation result for output current value produced 21
by a (12Vdc – 120 Vac) inverter circuit
3.5.3 Prototype circuit on breadboard 21
3.6 Screen Page 1 of SCADA control system design used 23
CX - Designer
3.6.1 Screen Page 2 of SCADA control system design used 24
CX - Designer
3.6.2 Sheet 1 of SCADA control system design used 24
CX-Designer
3.6.3 Ladder Diagram design used CX - Programmer 25
3.7 Outline of Project 26
4.1 Screen Page 1 SCADA system simulated use Test Mode 29
4.1.1 Screen Page 2 SCADA system simulated use Test Mode 29
4.1.2 Ladder diagram system in “ON” condition 30
4.1.3 Ladder diagram system in “LATCH” condition 31
4.1.4 Ladder diagram system in “OFF” condition 31
4.1.5 The combination system in “ON” condition simulates 32
used CX – Simulator
4.1.6 The combination system in “OFF” condition simulates 33
used CX – Simulator
4.2 Graph the output voltage (Vac) vs car speed (km/h) 34
4.2.1 Graph the output voltage (Vdc) vs car speed (km/h) 35
4.2.2 Graph the output current (Idc) vs car speed (km/h) 36
4.2.3 Graph the output power (Watt) vs car speed (km/h) 36
4.3 A complete project connected to CJ Series PLC type 37
LIST OF SYMBOLS
KE - Kinetic energy
m - Mass
v - Velocity/ speed of wind
A - Area
δ - Air density
t - Time
P - Power
ρ - Wind power density
pr - Standard atmospheric pressure at sea level (101325 Pa N/m2)
T - Air temperature (Kelvin)
g - Gravitational acceleration (9.8 m/s2)
h - Elevation of wind above sea level
π - pi = 3.142
r2 - (Foot blades)2
LIST OF ABBREVIATION
C - Capacitor
R - Resistor
D - Diode
Q - Transistor
T - Transformer
V - Voltage
I - Current
AC - Alternating Current
DC - Direct Current
WEC - Wind energy converter
HAWT - Horizontal-axis wind turbines
VAWT - Vertical axis wind turbines
PLC - Programmable Logic Controller
SCADA - Supervisory control and data acquisition
I/O - Input/ Output
RTU - Remote Terminal Unit
FYP - Final Year Project
UTeM - Universiti Teknikal Malaysia Melaka
LIST OF APPENDICES
APPENDIX TITLE PAGE
A Gantt Chart 41
B Ecava Visit Letter 42
C Betz Law 43
D Datasheet 2N3055 45
E Datasheet 2N6017 49
F Datasheet BC548 51
G Datasheet BD140 55
H I-Wind Vertical Axis Wind Turbine (VAWT) 57
Model Wind Data Specification
CHAPTER 1
INTRODUCTION
This chapter will discuss the overview of project background, wind energy,
problem statement, the aims and specific objectives of the project, and the project scope.
The end of this chapter will list the thesis outline.
1.1 Overview of Project Background
Today most of the countries began investing in renewable energy through various
programs that promote the development and testing of reliable alternative energy
resources. Renewable energy resources include wind, solar, hydroelectric, tidal, and
geothermal. The advantages of renewable energy compare to fossil energy are producing
much less pollutions than burning fossil fuels and are constantly replenished. This project
basically is to design and develop one type of renewable energy mini prototype plant with
SCADA system. Renewable energy resource that has been chose to generate this mini
plant is wind energy. The operation of this project is wind energy are use to rotate the
generator which will convert the mechanical energy that produce by the rotation to the
electrical energy. Next, the voltage produce by wind turbine will be converting to require
type of voltage use power electronic circuit (inverter). The operation of this mini prototype
plant can be monitor and control through SCADA system.
1.1.1 Wind Energy
The wind energy is converted through friction into diffuse heat throughout the
Earth's surface and the atmosphere. The origin of wind is complex. The Earth is unevenly
heated by the sun resulting in the poles receiving less energy from the sun than the equator
does. The dry land heats up (and cools down) more quickly than the seas. The differential
heating powers a global atmospheric convection system reaching from the Earth's surface
to the stratosphere which acts as a virtual ceiling. There are the main advantages and
disadvantages of wind power on the surrounding environment and the general reliability of
wind turbines [3].
• The advantages of wind energy:
1. Wind energy is extremely friendly to the surrounding environment, no fossil
fuels are burnt to generate electricity.
2. Wind turbines are great resources to generate energy in remote locations from
example mountain community. The turbines can be a range of different sizes in
order to support varying population’s level.
3. Another advantage of wind energy is when combined with solar electricity; this
energy source is great to provide a steady and reliable supply of electricity.
4. New technologies are making the extraction of wind energy much more
efficient. The wind is free, and able to cash in on more and more of this free
wind power.
• The disadvantages of wind energy:
1. The main disadvantage regarding wind power is down to the winds unreliability
factor. In many areas, the winds strength is too low to support a wind turbine and
for this the use of solar power is great alternative.
2. Wind turbine construction can last over a year, be very expensive and costly to the
surrounding nature environment during the build process.
3. A wind turbine can only support a specific population. Wind turbines aren't like
power stations, where just burn a bit more fuel to generate more energy when
need it.
4. The noise pollution produces from the rotation of wind turbine.
1.2 Problem Statement
Nowadays, most of the power plants use fossil fuels as the energy to implement the
operation to produce electricity to customer. As known, the capacity storage of fossil fuel
energy is decreasing and its price is unstable and increases frequently. Furthermore, this
energy has disadvantages by producing pollution to the environment. For example, the
burning coal process, which is to generate energy to operate the power plant, will cause the
air pollution.
A safe and clean alternative energy is required to replace the fossil energy. This
project uses renewable energy which is wind as an alternative energy to generate and
produce the electricity, since it is clean and safe for environment. Besides that, with the
implementation of this project, it also helps in teaching and learning development because
an educational plant that being interfaced with SCADA system.
1.3 Project Objectives
The main objectives of performing this project are:
To implement the research base on wind energy as an alternative to support
electricity generations.
To comprehend and develop SCADA system to monitor and control the operation
of a teaching and learning mini prototype plant.
To construct the proper hardware system (include generation system and power
electronic circuit) that can be well interface with SCADA system.
1.4 Project Scope
1. Inverter circuit
Construct an inverter circuit appropriate with data specification required for
this project.
2. The Turbine Fixture and Selection of Generator/ Motor
Search the types of generator or motor that compatible function as a
generation system for an inverter circuit.
3. Develop Project Circuit Board
Develop complete project circuit board from a several types of circuit such
as strip board or PCB.
4. SCADA System Development
Develop proper SCADA system use CX- Designer software to monitor and
control a circuit operation.
1.5 Thesis Outline
Chapter one present an introduction, overview of project background, problem statement;
project objectives, project scope, and the thesis outline.
Chapter two covers the literature review. In this chapter will discuss about wind turbines,
wind turbine system speed and energy calculations, power electronic circuit (inverter),
PLC, and SCADA system.
Chapter three covers the methodology of the project. In this chapter the project workflow
and schematic block diagram of the project will be shown.
Chapter four presents the results and discussion.
Lastly chapter five discusses the conclusions and stated recommendations for the future
works.
CHAPTER 2
LITERATURE REVIEW AND THEORETICAL BACKGROUND
2.1 Introduction
This chapter will explain in detail wind energy as one type of renewable energy
sources that worldwide use at this moment to support electricity power generation.
2.2 Wind Turbines
A wind turbine is a machine that can convert the kinetic energy of the wind into
electrical energy. Blowing wind rotates the blades of the turbine and the mechanism in it
can generate electricity upon this rotation [9]. All wind systems consist of a wind turbine, a
tower, wiring, and the “balance of system” components: controllers, inverters, and/or
batteries.
Rotors can have two or three blades, with three being more common. The best
indication of how much energy a turbine will produce is the diameter of the rotor, which
determines its “swept area,” or the quantity of wind intercepted by the turbine [4]. The
frame is the strong central axis bar onto which the rotor, generator, and tail are attached.
The tail keeps the turbine facing into the wind. Wind turbines have mainly two
types. Horizontal axis wind turbines (HAWT) and vertical axis wind turbines (VAWT).
The horizontal axis wind turbines shows in Figure 2.1 and the vertical axis wind turbines
shows in Figure 2.2. Both have advantages and disadvantages but horizontal axis ones are
more common due to higher efficiency [9].
HAWT Advantages
1. High efficiency because the blades always move perpendicularly to the wind,
receiving power through the whole rotation.
2. Variable blade pitch, which gives the turbine blades the optimum angle of attack.
3. Most are self-starting.
4. The blades of turbine are at the centre side of gravity, so this ensure for it stability.
HAWT Disadvantages
1. HAWTs require an additional yaw control mechanism to turn the blades toward the
wind.
2. The height can create local opposition based on impacts to view sheds.
3. Downwind variants suffer from fatigue and structural failure caused by turbulence.
Figure 2.1 – Horizontal axis wind turbines
VAWT Advantages
1. Easier to maintain because most of the main component parts are located near the
ground.
2. A wind start up speed for VAWTs is lower than HAWTs. Generally, the electricity
starting generate at 6 mph.
3. VAWTs may have a lower noise signature.
4. Vertical wind turbines have a higher airfoil pitch angle, giving improved
aerodynamics while decreasing drag at low and high pressures.
VAWT Disadvantages
1. Having rotors located close to the ground where wind speeds are lower due to wind
shear, VAWT may not produce as much energy at a given site as a HAWT with the
same footprint or height.
2. Most VAWT have low starting torque.
3. Most VAWT need to be installed on a relatively flat piece of land and some sites
could be too steep for them but are still usable by HAWT.
Figure 2.2 – Vertical axis wind turbines
2.2.1 Wind Turbine System Steps of Installation Amongst Industrial and Domestic
(Small Wind Generation System) [9]
Industrial
1. Wind Measurement: As annual electricity generation depends mainly on wind
speed, this step is of vital importance to be able to forecast the energy production.
2. Feasibility studies: This will be a detailed study to let know whether a proposed
system will be a feasible project or not.