Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set...
Click here to load reader
-
Upload
erica-west -
Category
Documents
-
view
219 -
download
0
description
Transcript of Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set...
![Page 1: Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.](https://reader037.fdocuments.us/reader037/viewer/2022100403/5a4d1b667f8b9ab0599b046b/html5/thumbnails/1.jpg)
Remove the three screws holding the helbow
1
![Page 2: Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.](https://reader037.fdocuments.us/reader037/viewer/2022100403/5a4d1b667f8b9ab0599b046b/html5/thumbnails/2.jpg)
Turn the highlighted part until you can see the set screw throught the hole in the yellow part
2
Note:there are 2 set-screws one upon the other.Remove both.
![Page 3: Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.](https://reader037.fdocuments.us/reader037/viewer/2022100403/5a4d1b667f8b9ab0599b046b/html5/thumbnails/3.jpg)
Remove the four screws that hold the yellow part
3
Now you should be able to separate the RED part fom the YELLOW part. Help yourself with 2 screwdriver or use the holes in the back of the helbow to help forcing out the part (as shown by the arrow).
![Page 4: Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.](https://reader037.fdocuments.us/reader037/viewer/2022100403/5a4d1b667f8b9ab0599b046b/html5/thumbnails/4.jpg)
Now inspect the condition of the blue part (RC_IIT_007_P_015)
4
Especially check that this small flat surface is not damaged or «rounded»
Alternatively you can send us a picture like this of your part and we ahould be able to tell what is the state.
![Page 5: Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.](https://reader037.fdocuments.us/reader037/viewer/2022100403/5a4d1b667f8b9ab0599b046b/html5/thumbnails/5.jpg)
Check that the RC_TLR_007_P_003_00 is tighely screwed onto RC_IIT_007_P_015
5
RC_TLR_007_P_003_00
RC_IIT_007_P_015
If they are loose, you can remove this screw, take the two parts apart, apply some thread locker and tighten everything back up
![Page 6: Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.](https://reader037.fdocuments.us/reader037/viewer/2022100403/5a4d1b667f8b9ab0599b046b/html5/thumbnails/6.jpg)
Now inspect the condition of the motor shaft
6Alternatively you can send us a picture like this of your part and we ahould be able to tell what is the state.
Make sure this flat on the shaft is not damaged
![Page 7: Remove the three screws holding the helbow 1. Turn the highlighted part until you can see the set screw throught the hole in the yellow part 2 Note: there.](https://reader037.fdocuments.us/reader037/viewer/2022100403/5a4d1b667f8b9ab0599b046b/html5/thumbnails/7.jpg)
Carefully remove the screw that hold the motor and inspect them
7
These are 2x M1.6x5 countersunk screws. Use the following precautions:
• Replace in any case after removal with like screws.
• Do apply some thread lock
• DO NOT USE LONGER SCREWS they will damage the motor.
• Do not over-tighten these screws, the thread will strip easily
If they are cut or broken most probably we will have to replace the pronosupination motor