Remote Operation Panel AK-HRP200G - Panasonic USA · 2012. 11. 7. · CC SHT SYNC SELECT SAVE/LOAD...

Model No. AK-HRP200G

Operating Instructions<Operations and Settings>

Remote Operation Panel

VQT4S52A (E)

z How the operating instructions are organized• Basics:

This manual describes how to connect the unit to the required equipment and set it up.Before installing the unit, be sure to read the <Basics> manual to ensure that you know how to install it correctly.

• Operations and Settings (this manual)Operations and Settings describe how to operate and set up the unit.

M1012KT0 -PS

ENGLISH

Before operating this product, please read the instructions carefully and save this manual for future use.

2 3

Contents

Introduction............................................................................................. 3

Setup.mode............................................................................................. 4Setup mode.......................................................................................... 4

Setup.Mode.Operations......................................................................... 71. Set camera number ......................................................................... 72. Save scene file to/load scene file from memory card ...................... 73 Saving user files to/loading user files from memory card ................. 84 Save lens file to/load lens file from memory card ............................. 95 Save ROP configuration file to/load ROP configuration file from

memory card .................................................................................... 96 Format memory card....................................................................... 107 Select/set flare and pedestal........................................................... 108. Set buzzer (beep/call tone) ............................................................ 119 Display brightness setting (LED/7-segment display) ...................... 1116 Initialize settings............................................................................ 1117 Confirm version ............................................................................. 1218 Save unit data to memory card ..................................................... 1219 Software upgrade.......................................................................... 12Error messages in setup mode .......................................................... 13

ROP.menu.operations.......................................................................... 14ROP menus that can be operated on the unit.................................... 14Operating ROP menus....................................................................... 14

ROP.menu.setting................................................................................ 16SHADING(WHITE) ............................................................................. 16PEDESTAL/FLARE/GAIN .................................................................. 16GAMMA/BLACK.GAMMA .................................................................. 17CINEMA GAMMA .............................................................................. 17KNEE/WHITE CLIP ............................................................................ 18MATRIX (1/2) ..................................................................................... 18MATRIX (2/2) ..................................................................................... 19HD DTL/SKIN DTL (1/2) .................................................................... 19HD DTL/SKIN DTL (2/2) .................................................................... 20SD DETAIL ........................................................................................ 20SYSTEM (1/2) .................................................................................... 21SYSTEM (2/2) .................................................................................... 22FUNCTION ........................................................................................ 22LENS FILE/EDIT (1/2) ....................................................................... 23LENS FILE/EDIT (2/2) ....................................................................... 23

Data.handled.in.the.studio.camera.system....................................... 24

Data.item.list......................................................................................... 25

Index...................................................................................................... 36

��About.trademarks.and.registered.trademarks.• SDHC logo is a trademark of SD-3C, LLC.• Other company names and product names appearing in this manual are the registered trademarks or trademarks of their respective companies.

��CopyrightsIt is prohibited to transfer, copy, disassemble, decompile, and reverse engineer the software included with the unit, as well as export it in violation of the export laws.

��AbbreviationsThe following abbreviations are used in this manual.• SD memory cards and SDHC memory cards are both referred to as “memory cards”. They are referred to individually in descriptions in which each

of them is discussed separately.• Personal computers are referred to as "computers."• Studio handy camera is referred to as “camera”.• Camera control unit is referred to as "CCU".• Remote operation panel is referred to as “ROP”.

�� Illustrations.and.screen.images.in.this.manual• Illustrations of the unit and screens may appear different from the actual unit and screens.

2 3

Introduction

��OverviewThis unit is a remote operation panel for controlling a studio handy camera (AK-HC3800) and a camera controller unit like the AK-HCU200.Use a dedicated optical fiber cable to connect a studio handy camera to a camera controller unit and use a dedicated ROP cable (optional accessory) to connect this unit to the camera controller unit.

��Memory.CardsMemory cards used with the unit should conform to SD or SDHC standards.Be sure to use the unit to format memory cards.Memory cards with the following capacity can be used with the unit.SDXC memory cards are not supported.

SD memory cards: 8 MB to 2 GBSDHC memory cards: 4 GB to 32 GB

For the latest information not described in the Operating Instructions, refer to the following website.

http://pro-av.panasonic.net/

Observe the following points when using and storing this unit.• Avoid high temperature and humidity.• Avoid water droplets.• Avoid static electricity.

��Upgrade.softwareYou can obtain upgrade software from Service and Support on the following website.

http://panasonic.biz/sav/

For the upgrade procedure, refer to the instructions included with the download file.

��Software.for.peripheral.equipmentSoftware upgrades will also become necessary for the peripheral equipment that is connected to this unit (cameras or CCUs).For details, consult your supplier.

��Disclaimer.of.warrantyIN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:

(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;

(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER;

(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER;

(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;

(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;

(6) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE;

��File.types.handled.by.the.unitScene file Scene files are mainly used by video

engineers (VE) to create the required image characteristics.

Reference file The term reference file is a generic term for user files and factory files.

User file A user file is system setting data (reference file) composed of scene files and operation data. The user can record user files.

Factory file A file that contains camera settings that were stored at the factory.

Lens file Data for correcting specific lens characteristics that are used by video engineers (VE).

ROP configuration file ROP specific setting data.

4 5

Setup.mode

Setup.modeSetup mode allows the user to make a variety of unit settings, and save and load scene files and user files.Normal operation is unavailable during setup mode operation. ROP menu (REMOTE OPERATION MENU) operation is not available either.

��Setup.mode.functionsSetup mode allows you to do any of the following.

Item Adjustable.range Display1 Set camera number Sets a camera number.

2 Save scene file to/load scene file from memory card Saves the currently used scene file to a memory card. It also allows you to load a scene file stored on a memory card.

3 Save user file to/load user file from memory card Saves the currently used user file to a memory card. It also allows you to load a user file stored on a memory card.

4 Save lens file to/load lens file from memory card Saves the currently used lens file to a memory card. It also allows you to load a lens file stored on a memory card.

5 Save ROP configuration file to/load ROP configuration file from memory card

Save a configuration file for the unit to a memory card. It also allows you to load a configuration file for the unit stored on a memory card.

6 Format memory card Formats a memory card

7 Select/set flare and pedestal Selects the flare and pedestal control function

8 Set buzzer (beep/call tone) Enables or disables the buzzer or call tone.

9 Set display brightness (LED/7-segment display) Sets the brightness of the panel LED and 7-segment display.

10

For future use.

11

12

13

14

15

16 Initialize settings Initializes unit settings.

17 Confirm version Displays the version of the software used by the unit.

18 Save unit data to memory card Saves unit data to a memory card.

19 Upgrade software Upgrades the software used by the unit.

4 5

Setup.mode. (continued)

��Opening.setup.modeSetup mode differs from normal operating modes. Use the steps below to open setup mode.

1..When.a.camera.and.CCU.are.connected,.select.IRIS.(to.light.the.<IRIS>.display.on.the.panel).If the IRIS display is not lit, press the selected <DISPLAY SELECT> button to select IRIS.

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN

SET UP ND/CC M.GAIN/M.PED SHUTTER

ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT

EXECUTEEXITSAVE/LOAD

SHIFT+

UP+DOWN

IRIS display

Use the steps below to open setup mode when the power is on, but a camera or CCU is not connected.

2..Simultaneously.hold.down.DATA.SET.<DATA.SET>.<UP>,.<DOWN>.and.<SHIFT>.for.approximately.two.seconds.This opens setup mode and Menu No. 1 (camera number setting) is displayed.

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

SCENE 4 STORESCENE 3SCENE 2SCENE/USER FILE

SCENE 1

USER 3USER 2USER 1

SHIFT

��Exiting.setup.modeTo exit setup mode, hold down <EXIT> for two seconds. The unit returns to normal operating mode.

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

��Basic.operationsThe buttons indicated in the figure below are available in setup mode. No other buttons are available. All other LEDs stay off. (Except the alarm display)

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

1

567 8

2 43

1..Selects.set.values

2..Indicates.selected.submenu

3..Indicates.set.values.and.selected.values

4..Indicates.menu.numbers

5..Selects.a.menu.number..Each.press.of.the.button.increments.menu.numbers.1→2→3→...→19→1→2→...

6..Confirms.a.setting

7..Selects.a.submenu..Each.press.of.the.button.opens.a.different.submenu.

8..To.exit.setup.mode,.hold.down.<EXIT>.for.two.seconds..The.unit.returns.to.normal.operating.mode.

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

6

Setup.mode. (continued)

7

��Setup.mode.menu.configurationSetup mode is comprised of the menus and submenus listed in the table below.

Menu Submenu Set.value/Selected.operation Default.value

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Press <SELECT>to select a menu number. Press <SAVE/LOAD> to select a submenu. Use <UP> or <DOWN> to select a set value or an operation.Use <EXECUTE> to confirm an entry.

No. Menu.item Light.indication

Settings.and.operations 7-segment.display.(display.and.selection)

1 Set camera number*1 - - Camera number (1 to 19) 1

2 Save scene file to/load scene file from memory card

ND Save to memory card Scene files (1 to 4) 1

CC Load from memory card Scene files (1 to 4) 1

3 Save user file to/load user file from memory card

ND Save to memory card User files (1 to 3) 1

CC Load from memory card User files (1 to 3) 1

4 Save lens file to/load lens file from memory card

ND Save to memory card Lens files (1 to 32) 1

CC Load from memory card Lens files (1 to 32) 1

5 Save ROP configuration file to/load ROP configuration file from memory card

ND Save to memory card - -

CC Load from memory card - -

6 Format memory card*1 - - - -

7 Select/set flare and pedestal*1 - - FLARE/PED (FL/PE) FL

8 Set buzzer (beep/Call)*1 - - Enable/disable buzzer (on/off) on

9 Set display brightness (LED/7-segment display)

ND LED 3 levels (bright/intermediate/low) Bright

CC 7-segment display 3 levels (bright/intermediate/low) Bright

10

For future use.

11

12

13

14

15

16 Initialize settings - - - -

17 Confirm version ND Display version No (first digits) Displays the first 3 digits -

CC Version No (middle digits) Displays the middle 2 digits -

SHT Version No (last digits) Displays the last 3 digits -

18 Save unit data to memory card - - - -

19 Upgrade software - - - -

*1 These functions are controlled by Save ROP configuration file to/load ROP configuration file from memory card These functions are initialized when you perform settings initialization.

��Files.stored.on.a.memory.cardIn setup mode, the following files are saved to or loaded from a memory card by the unit. The fixed file names assigned by the unit must not be changed on a computer. If the file names are changed, they can no longer be processed by the unit.

Files.stored.on.a.memory.card FilenameScene file SCENE1.BIN to SCENE4.BIN

User file USER1.BIN to USER3.BIN

Lens file LENS01.BIN to LENS32.BIN

ROP configuration file ROP_OPE.BIN

Unit data file ROP_INFO.BIN

6 7

Setup.Mode.Operations

<Note>Menu numbers 10 to 15 are for future use.

1..Set.camera.number

1..Open.setup.mode.and.check.that.menu.number.[1].is.displayed..If.a.menu.number.other.than.[1].appears,.press.<SELECT>.to.select.menu.number.[1].

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Press to select the menu number

Press to exit setup mode (hold down)

Press to confirm the camera number

Press to select the camera number

2..Press.<UP>.or.<DOWN>.to.select.a.camera.number.and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

To select camera number 2

• Camera numbers become available after exiting setup mode.• To exit setup mode, hold down <EXIT> for about 2 seconds.• To make other settings, press <SELECT> to select a menu number.

2..Save.scene.file.to/load.scene.file.from.memory.cardCurrent operating status data is saved as a scene file to the memory card.

Press.<SELECT>to.select.menu.number.[2].

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

ND CC



Press to confirm

Select file number, Select y (Select)/n (Cancel)

Press to save/load

Save file indicationLoad file indication

2-1.Save.scene.file.to.memory.card1..Press.<SAVE/LOAD>.to.select.[ND].

• Each press of <SAVE/LOAD> toggles between [ND] (Save) and [CC] (load).

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

2..Press.<UP>.or.<DOWN>.to.select.a.file.number.on.the.memory.card.and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

To save a file to file no. 2 on the memory card

3..Press.<UP>.or.<DOWN>.to.select.[y].and.press.<EXECUTE>.to.confirm.the.selection.• Do not remove a memory card that is being accessed.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

• To cancel saving, select [n] and press <EXECUTE>.• The file is saved to the memory card and [Fin] appears when saving

ends.• [E02] is displayed if the save operation to the memory card fails.

(→page 13) If this happens, check the memory card and try again or insert another memory card to perform the operation again.

• [E01] is displayed when a scene file with the same name as the one you are attempting to save already exists on the memory card. To overwrite the file, press <UP> or <DOWN> to select [y] and press <EXECUTE>.(→page 13)

• To exit setup mode, hold down <EXIT> for about 2 seconds.• To make other settings, press <SELECT> to select a menu number.

2-2.Load.scene.file.from.memory.cardScene file data loaded from the memory card is returned to the operating status. (It is not returned to scene files 1 to 4. To return the data to scene files 1 to 4, exit setup mode and store the data in one of scene files 1 to 4. For details, refer to <Operations>, the instruction manual.)

1..Press.<SAVE/LOAD>.to.select.[CC].• Each press of <SAVE/LOAD> toggles between [ND] (Save) and

[CC] (load).ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


ND

M.GAIN

IRIS

M.PED

CC SHT SYNCCC

To load file no. 2 from the memory card


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

8

Setup.Mode.Operations. (continued)

9

• To cancel loading, select [n] and press <EXECUTE>.• The file is loaded from the memory card and [Fin] appears when

loading ends.• [E02] is displayed if the load operation from the memory card fails.

(→page 13)If this happens, check the memory card and see whether the file exists on the memory card. If it does, start over from step 1.


3.Saving.user.files.to/loading.user.files.from.memory.card


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN





Press to confirmPress to save/load

3-1.Save.user.file.to.memory.cardCurrent operating status data is saved as a user file to the memory card.

1..Press.<SAVE/LOAD>.to.select.[ND].• Each press of <SAVE/LOAD> toggles between [ND] (Save) and

[CC] (load).ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC



ND

M.GAIN

IRIS

M.PED

CC SHT SYNC



(→page 13) If this happens, check the memory card and try again or insert another memory card to perform the operation again.

• [E01] is displayed when a user file with the same name as the one you are attempting to save already exists on the memory card.To overwrite the file, press <UP> or <DOWN> to select [y] and press <EXECUTE>.(→page 13)


3-2.Load.scene.file.from.memory.cardUser file data loaded from the memory card is returned to the operating status. (It is not returned to user files 1 to 3. To return the data to user files 1 to 3, exit setup mode and store the data in one of user files 1 to 3. For details, refer to <Operations>, the instruction manual.)

1..Press.<SAVE/LOAD>.to.select.[CC].• Each press of <SAVE/LOAD> toggles between [ND] (Save) and

[CC] (load).ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC



ND

M.GAIN

IRIS

M.PED

CC SHT SYNC





8 9


4.Save.lens.file.to/load.lens.file.from.memory.card


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN






4-1.Save.lens.file.to.memory.card1..Press.<SAVE/LOAD>.to.select.[ND].


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC



ND

M.GAIN

IRIS

M.PED

CC SHT SYNC



(→page 13)If this happens, check the memory card and try again or insert another memory card to perform the operation again.

• [E01] is displayed when a lens file with the same name as the one you are attempting to save already exists on the memory card.To overwrite the file, press <UP> or <DOWN> to select [y] and press <EXECUTE>.(→page 13)

• [E04] is displayed when the lens file is off.


4-2.Load.lens.file.from.memory.card1..Press.<SAVE/LOAD>.to.select.[CC].

• Each press of <SAVE/LOAD> toggles it between [ND] (Save) and [CC] (Load).

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC



ND

M.GAIN

IRIS

M.PED

CC SHT SYNC




• [E04] is displayed when the lens file is off.


5..Save.ROP.configuration.file.to/load.ROP.configuration.file.from.memory.card


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Select y (Select)/ n (Cancel)





10


11

5-1.Save.ROP.configuration.file.to.memory.card1..Press.<SAVE/LOAD>.to.select.[ND].


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC



(→page 13)If this happens, check the memory card and try again or insert another memory card to perform the operation again.

• [E01] is displayed when an ROP configuration file with the same name as the one you are attempting to save already exists on the memory card.To overwrite the file, press <UP> or <DOWN> to select [y] and press <EXECUTE>.(→page 13)

• For details on Save/Load data, refer to page 6.


5-2.Load.ROP.configuration.file.from.memory.card1..Press.<SAVE/LOAD>.to.select.[CC].


ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.<EXECUTE>.to.confirm.the.selection.• The file is loaded from the memory card and [Fin] appears when

loading ends. A few seconds later, the unit is restarted.• Do not remove a memory card that is being accessed.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

• To cancel loading, select [n] and press <EXECUTE>.• [E02] is displayed if the load operation from the memory card fails.


• To exit setup mode, hold down <EXIT> for about 2 seconds.

6.Format.memory.card

1..Press.<SELECT>to.select.menu.number.[6].

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Select y (Format)/n (Cancel)



Press to confirm

2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.<EXECUTE>.to.confirm.the.selection.• Card formatting starts.• Do not remove a memory card that is being accessed.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

• To cancel formatting, select [n] and press <EXECUTE>.• When the formatting ends, [Fin] appears.


7.Select/set.flare.and.pedestal


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Select FL (Flare)/PE (Pedestal)



Press to confirm

7-1.Set.flarePress.<UP>.or.<DOWN>.to.select.[FL].and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


10 11


7-2.Set.pedestalPress.<UP>.or.<DOWN>.to.select.[PE].and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


8..Set.buzzer.(beep/call.tone)


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Select on/off



Press to confirm

2..Press.<UP>.or.<DOWN>.to.select.[on].and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


9.Display.brightness.setting.(LED/7-segment.display)


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Adjust brightnessLED display brightness

7-segment display brightness



Press to confirmLED/7-segment display switch

9-1.Set.LED.brightness1..Press.<SAVE/LOAD>.to.select.[ND].and.press.<EXECUTE>.to.confirm.the.selection.• Each press of <SAVE/LOAD> toggles between [ND] (LED display

brightness) and [CC] (7-segment display brightness).ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

2..Press.<UP>.or.<DOWN>.to.select.LED.display.brightness.and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


9-2.Set.7-segment.display.brightness1..Press.<SAVE/LOAD>.to.select.[CC].and.press.<EXECUTE>.to.confirm.the.selection.• Each press of <SAVE/LOAD> toggles between [ND] (LED display

brightness) and [CC] (7-segment display brightness).ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

2..Press.<UP>.or.<DOWN>.to.select.7-segment.display.brightness.and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC


Menu.numbers.10.to.15.are.for.future.use.

16.Initialize.settings

<Note>When settings are initialized, the unit is automatically restarted.For details on what settings are initialized, refer to page 6


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN


Press to confirm

Select y (Initialize)/n (Cancel)

12


13

2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.<EXECUTE>.to.confirm.the.selection.• After confirmation, unit settings are initialized and it is automatically

restarted.ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

• To cancel initializing, select [n] and press <EXECUTE>.

17.Confirm.version

Press.<SELECT>to.select.menu.number.[17].• The version information is displayed.• Press <SAVE/LOAD> to show the 8-digit version number split up in 3,

2 and 3 digits.

CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Press to select the menu numberPress to switch display digits

Display digit indication (first 3 digits)Display digit indication (middle 2 digit)Display digit indication (last 3 digits)



18.Save.unit.data.to.memory.cardThis functions are used by the manufacturer during maintenance.


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN


Press to confirm

Select y (Save)/n (Cancel)


2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.<EXECUTE>.to.confirm.the.selection.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

• The file is saved to the memory card and [Fin] appears when saving ends.

• [E02] is displayed if the save operation to the memory card fails.(→page 13)If this happens, check the memory card and try again or insert another memory card to perform the operation again.

• [E01] is displayed when a unit data file with the same name as the one you are attempting to save already exists on the memory card.To overwrite the file, press <UP> or <DOWN> to select [y] and press <EXECUTE>. (→page 13)


19.Software.upgradeFor details on software upgrades, refer to "Software upgrades"(→page 3).


CAMERA

No.

DATASET

DISPLAY SELECT

UP

DOWN


ND

M.GAIN

IRIS

M.PED 10-19

CC SHT SYNC

SELECT


SHIFT+

UP+DOWN

Select y (Upgrade)


Press to confirm


2..Press.<UP>.or.<DOWN>.to.select.[y].and.press.<EXECUTE>.to.confirm.the.selection.• Upgrading starts.

ND

M.GAIN

IRIS

M.PED

CC SHT SYNC

• When the upgrade ends, [Fin] appears.

<Note>If the upgrade fails for some reason, <SHIFT> may start to flash after the restart. If this happens, perform the upgrade process again.

12 13


Error.messages.in.setup.mode

Error.No. Error.dataE01 A file with the same name already exists. Select [y]

to overwrite.

E02 An error occurred on the memory card.• Check if a file with the same name already exists.• Check if the memory card is write protected.• Check if there is any free space left on the P2 card.

E03 A memory card has not been inserted.• The lens file is off.

E04 A communication error occurred. Check the connected equipment.

E05 An error occurred. Start over from the beginning.

��When.a.file.with.the.same.name.exists.on.the.memory.card[E01] is displayed when a file with the same name as the one you are attempting to save already exists on the memory card.To overwrite the file, press <UP> or <DOWN> to select [y] and press <EXECUTE>.

��When.E02.to.E05.are.displayedPress <EXECUTE> to close the error message. Then perform the operation again.

14 15

ROP.menu.operations

ROP.menus.that.can.be.operated.on.the.unitThe unit can access the picture monitor on a CCU to control the ROP menu (REMOTE OPERATION MENU).

��Opening.menus.and.menu.configuration

CHARA

MENU

SELECT

REMOTE OPERATION MENU

SHADING(WHITE)

PEDESTAL/FLARE/GAIN

GAMMA/BLACK GAMMA

CINEMA GAMMA

KNEE/WHITE CLIP

MATRIX

HD DTL/SKIN DTL

SD DETAIL

SYSTEM

FUNCTION

LENS FILE/EDIT

Hold down <CHARA/MENU> for about 2 seconds to open [REMOTE OPERATION MENU]. To close [REMOTE OPERATION MENU], hold down <CHARA/MENU> for about 2 seconds.

Use <SELECT> to select the menu.

Menus cannot be displayed when any of the following messages appear on the picture monitor.• WARNING message• AUTO message• STATUS messageIf any of these messages appear, you can hold down <CHARA/MENU> to delete them and resume operation.

When camera power <HEAD POWER> is Off, only [SYSTEM] can be selected.

Operating.ROP.menus

��Basic.menu.operations

1..Hold.down.<CHARA/MENU>.for.2.seconds.The [REMOTE OPERATION MENU] appears. (The cursor appears at the beginning of the first line.)

CHARA

MENU

SELECT

→＊　ＲＥＭＯＴＥ　ＯＰＥＲＡＴＩＯＮ　ＭＥＮＵ　＊

ＳＨＡＤＩＮＧ（ＷＨＩＴＥ）ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮＧＡＭＭＡ／ＢＬＡＣＫ　ＧＡＭＭＡＣＩＮＥＭＡ　ＧＡＭＭＡＫＮＥＥ／ＷＨＩＴＥ　ＣＬＩＰＭＡＴＲＩＸＨＤ　ＤＴＬ／ＳＫＩＮ　ＤＴＬＳＤ　ＤＥＴＡＩＬＳＹＳＴＥＭＦＵＮＣＴＩＯＮＬＥＮＳ　ＦＩＬＥ／ＥＤＩＴ

Cursor

2..Turn.<SELECT>.one.click.clockwise.to.move.the.cursor..

CHARA

MENU

SELECT

→

＊　ＲＥＭＯＴＥ　ＯＰＥＲＡＴＩＯＮ　ＭＥＮＵ　＊

ＳＨＡＤＩＮＧ（ＷＨＩＴＥ）ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮＧＡＭＭＡ／ＢＬＡＣＫ　ＧＡＭＭＡＣＩＮＥＭＡ　ＧＡＭＭＡＫＮＥＥ／ＷＨＩＴＥ　ＣＬＩＰＭＡＴＲＩＸＨＤ　ＤＴＬ／ＳＫＩＮ　ＤＴＬＳＤ　ＤＥＴＡＩＬＳＹＳＴＥＭＦＵＮＣＴＩＯＮＬＥＮＳ　ＦＩＬＥ／ＥＤＩＴ

Cursor

3..Press.<SELECT>to.select.a.menu.The [SHADING(WHITE)] menu appears.In this state (when the cursor is in the menu title), press <SELECT> to return to the next higher menu ([ROP MENU]).

CHARA

MENU

SELECT

＊＊　ＳＨＡＤＩＮＧ（ＷＨＩＴＥ）　＊＊

ＷＨＩＴＥ　ＳＨＡＤＩＮＧ　ＳＷＩＴＣＨ

→

ＧＢ

ＲＨＳＡＷ　ＨＰＲＡ　ＶＳＡＷ　ＶＰＡＲＡ

　ＯＮ

　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０

4..Turn.<SELECT>.to.move.the.cursor.to.a.setting.and.press.<SELECT>.The selected setting flashes allowing you to change the set value.


ＷＨＩＴＥ　ＳＨＡＤＩＮＧ　ＳＷＩＴＣＨ→

ＧＢ


　ＯＮ

　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０

Flashing

CHARA

MENU

SELECT

<Note>Turn <SELECT> quickly to change the hundreds place of a set value.

14 15

ROP.menu.operations. (continued)

��Operating.other.menusWhen a menu has more than one setting on a line, press <SELECT> (to confirm) and the cursor [] appears.Turn <SELECT> right or left to move the cursor to the input area.

↓ ↓↓↓ ↓



ＧＢ


　ＯＮ

　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０

Cursor movement

In a character entry menu, the [] cursor will also appear.

＊＊ＬＥＮＳ　ＦＩＬＥ/ ＥＤＩＴ( １/ ２）　＊＊

ＦＩＬＥ　ＮＯ

ＦＩＬＥ　ＮＡＭＥ

ＥＸＥＣＵＴＥ

ＭＯＤＥ

↓↓↓↓↓↓↓↓↓

ＬＯＡＤ

ＮＯ？

Cursor movement

When the cursor is at the beginning of a menu, press <SELECT> to confirm to turn the cursor into [] to continue selecting menu items.

↓



→ＧＢ


　ＯＮ

　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０



ＧＢ


　ＯＮ

　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０

16 17

ROP.menu.setting

The following describes [ROP MENU] settings.

SHADING(WHITE)



→

ＧＢ


　ＯＮ

　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０　　　　　　０　　　　０　　　　０　　　　　０

( indicates factory default settings.)Item Display .Function

WHITE.SHADING.SWITCH

OFFON

Enables/disables white shading.

H.SAW.R -100׀0׀

100

Performs sawtooth wave correction of white screen images in the horizontal direction.

H.SAW.G

H.SAW.B

H.PARA.R -100׀0׀

100

Performs parabola correction of white screen images in the horizontal direction.H.PARA.G

H.PARA.B

V.SAW.R -100׀0׀

100

Performs sawtooth wave correction of white screen images in the vertical direction.V.SAW.G

V.SAW.B

V.PARA.R -100׀0׀

100

Performs parabola correction of white screen images in the vertical direction.V.PARA.G

V.PARA.B

PEDESTAL/FLARE/GAIN

→＊＊　ＰＥＤＥＳＴＡＬ／ＦＬＡＲＥ／ＧＡＩＮ　＊＊

ＦＬＡＲＥ　ＳＷＩＴＣＨ

ＦＬＡＲＥＧＡＩＮ

ＭＡＳＴＥＲ　ＰＥＤＥＳＴＡＬ

ＰＥＤＥＳＴＡＬＲＧＢ

　ＯＮ

０００００

０

０００

( indicates factory default settings.)Item Display Function

FLARE.SWITCH OFFON

Set to On to adjust flare correction amount.Flare correction controls the increase in pedestal level in proportion to light intensity.

MASTER.PEDESTAL

-99׀0׀

99

Indicates set master pedestal value. (Settings cannot be made.)

PEDESTAL.R -800׀0׀

800

Amount by which the level is increased or decreased relative to the G pedestal to adjust the black balance. When the auto black balance is achieved, 0 is set as the adjustment value.

PEDESTAL.G -800׀0׀

800

Adjusts the amount of G pedestal offset from master pedestal.

PEDESTAL.B -800׀0׀

800

Amount by which the level is increased or decreased relative to the G pedestal to adjust the black balance. When the auto black balance is achieved, 0 is set as the adjustment value.

FLARE.R -100׀0׀

100

Adjusts the amount of R FLARE correction.

FLARE.G -100׀0׀

100

Adjusts the amount of G FLARE correction

FLARE.B -100׀0׀

100

Adjusts the amount of B FLARE correction

GAIN.R -800׀0׀

800

Adjusts the white balance.Amount by which the R gain has to be increased or decreased relative to the G gain level. When the auto white balance is achieved, 0 is set as the adjustment value.

GAIN.B -800׀0׀

800

Adjusts the white balance.Amount by which the B gain has to be increased or decreased relative to the G gain level. When auto white balance is achieved, 0 is set as the adjustment value.

16 17

ROP.menu.setting. (continued)

GAMMA/BLACK.GAMMA

０．４５０

＊＊　ＧＡＭＭＡ／ＢＬＡＣＫ　ＧＡＭＭＡ　＊＊

ＧＡＭＭＡ　ＳＷＩＴＣＨ

ＧＡＭＭＡ

ＢＬＡＣＫ　ＧＡＭＭＡ

ＤＲＳ　ＳＷＩＴＣＨＥＦＥＣＴ　ＤＥＰＴＨ

ＰＲＥ－ＣＯＲＲＥＣＴＩＯＮ

ＢＬＡＣＫ　ＧＡＭＭＡ　ＳＷＩＴＣＨ

ＯＮ

ＯＦＦ

ＯＦＦ

Ｒ

Ｒ

００

０

５

００

４．５

Ｍ

Ｍ

Ｂ

Ｂ

→


GAMMA.SWITCH OFFON

Turn on to correct the gamma.Gamma provides the signal level of the TV video signal with characteristics that are the reverse of those for video signal input and light intensity level.

GAMMA.R zVIDEO REC-75|0|

75 zFILMLIKE1 to 3

-60|

60

Adjusts R gamma correction relative to M gamma.

GAMMA.M 0.300׀

0.450׀

0.750

Adjusts the master gamma.

GAMMA.B zVIDEO REC-75|0|

75 zFILMLIKE1 to 3

-60|

60

Adjusts B gamma correction relative to M gamma.

BLACK.GAMMA.SWITCH

OFFON

Turn this switch on to correct the black gamma.It changes the amplification rate of the video signal in low light intensity areas.

BLACK.GAMMA.R

-20.(black.compression)

׀0׀

20.(black.expansion)

Corrects the black gamma curve R.

BLACK.GAMMA.M


׀0׀


Corrects the black gamma.

BLACK.GAMMA.B


׀0׀


Corrects the black gamma curve B.

Item Display FunctionDRS.SWITCH OFF

ONTurn on for automatic contrast adjustment.This adaptive-type gamma correction adjusts the gamma correction to the optimal setting.

EFFECT.DEPTH 1׀5

Turn on for contrast adjustment.Higher numbers mean greater effect.

PRE-CORRECTION

4.04.55.0.

Turn on to adjust the rising slope in low-light areas.

CINEMA.GAMMA

<Note>• The settings in this menu are not available when the [CINEMA

GAMMA SWITCH] is set to [OFF].

→＊＊　ＣＩＮＥＭＡ　ＧＡＭＭＡ　＊＊

ＣＩＮＥＭＡ　ＧＡＭＭＡ　ＳＷＩＴＣＨ

ＣＩＮＥＭＡ　ＧＡＭＭＡ　ＳＥＬＢＬＡＣＫ　ＳＴＲＥＴＣＨ　ＬＥＶＥＬＤＹＮＡＭＩＣ　ＬＥＶＥＬ

ＫＮＥＥ　ＰＯＩＮＴＫＮＥＥ　ＳＬＯＰＥ

ＣＩＮＥＭＡ　ＴＹＰＥＯＦＦ

２００％

１５０％

０

３０

ＶＩＤＥＯＶＩＤＥＯ＿ＲＥＣ


CINEMA.GAMMA.SWITCH

OFFON

Enables or disables cinema gamma mode.

CINEMA.TYPE VIDEOFILM

Switches between cinema gamma characteristics for video and those for film

CINEMA.GAMMA.SEL

zWhen [CINEMA TYPE] is set to [VIDEO]

VIDEO_RECFILMLIKE1FILMLIKE2FILMLIKE3

zWhen [CINEMA TYPE] is set to [FILM]

FILM_REC.(fixed).

Sets cinema gamma characteristics for video.

BLACK.STRETCH.LEVEL

0׀

30.

This function is available only when the [CINEMA GAMMA SWITCH] is set to [ON] and [CINEMA TYPE] is set to [FILM].

DYNAMIC.LEVEL

200%/300%/400%/500%.

Sets the dynamic rangeThis function is available only when [CINEMA TYPE] is set to [FILM].

KNEE.POINT*1 30׀

90

Sets the master knee point.Turn the Select dial clockwise to increase the knee point value. (The numbers decrease.)

KNEE.SLOPE*1 150%/200%/250%/300%/350%/400%/450%/500%/550%/600%.

Sets the master knee slope.

*1 When the Knee OFF button <KNEE OFF> is On or when [KNEE SWITCH] is set to [OFF] in the [KNEE/WHITE CLIP] menu, settings cannot be changed.

18


19

KNEE/WHITE.CLIP

<Note>• Some settings in this menu are not available when the [CINEMA

GAMMA SWITCH] is set to [ON].

→＊＊　ＫＮＥＥ／ＷＨＩＴＥ　ＣＬＩＰ　＊＊

ＫＮＥＥ　ＳＷＩＴＣＨ

ＰＯＩＮＴ

ＷＨＩＴＥ　ＣＬＩＰ　ＳＷＩＴＣＨ

ＣＬＩＰ

ＨＩ　ＣＯＬＯＲ

ＳＬＯＰＥ

ＯＮ

ＯＦＦ

ＯＮ

Ｒ００

００

００

９５．０％１３０％

１０９％

ＭＢ

ＲＭＢ


KNEE.SWITCH OFF/ON Turn on to adjust the knee slope and knee point.

POINT.R -20׀0׀

20.

Sets the R knee point.

POINT.M 80.0%׀

95.0%׀

110.0%.

Sets the master knee point.

POINT.B -20׀0׀

20.

Sets the B knee point.

SLOPE.R -31׀0׀

31.

Sets the R knee slope.

SLOPE.M 0׀

130׀

199

Sets the master knee slope.

SLOPE.B -31׀0׀

31.

Sets the B knee slope.

WHITE.CLIP.SWITCH

OFFON

Enables or disables the white clip function.

CLIP.R -15׀0׀

15

Sets the R white clip function.

CLIP.M 80%׀

109%

Sets the master white clip function.

CLIP.B -15׀0׀

15

Sets the B white clip function.

HI.COLOR OFFON

Turn on to improve the color reproducibility in the high-brightness areas.

MATRIX.(1/2)

→＊＊　ＭＡＴＲＩＸ（１／２）　＊＊

ＰＲＥＳＥＴ

ＭＡＴＲＩＸ　ＳＷＩＴＣＨ

ＭＥＭＯＲＹＲ－ＧＲ－ＢＧ－ＲＧ－ＢＢ－ＲＢ－Ｇ

ＮＯＲＭＡＬ

ＯＦＦ

Ａ００００００


PRESET NORMALEBU

NTSC

Switches matrix presets.

MATRIX.SWITCH OFFON

Enables or disables saturation and color phase correction.

MEMORY OFFAB

Select matrix memory to adjust.

.R-G -63׀0׀

63

Adjusts the saturation and color phase of R and G components in matrix memory.

R-B -63׀0׀

63

Adjusts the saturation and color phase of R and B components in matrix memory.

G-R -63׀0׀

63

Adjusts the saturation and color phase of G and R components in matrix memory.

G-B -63׀0׀

63

Adjusts the saturation and color phase of G and B components in matrix memory.

B-R -63׀0׀

63

Adjusts the saturation and color phase of B and R components in matrix memory.

B-G -63׀0׀

63

Adjusts the saturation and color phase of B and G components in matrix memory.

18 19


MATRIX.(2/2)

→＊＊　ＭＡＴＲＩＸ（２／２）　＊＊

１２ＡＸＩＳＭＥＭＯＲＹ

ＧＳＡＴＰＨＡＳＥＳＡＴＰＨＡＳＥ

ＣｙＢＭｇＲＹｅ

Ｇ＿ＣｙＣｙ＿ＢＢ＿ＭｇＭｇ＿ＲＲ＿ＹｅＹｅ＿Ｇ

Ａ

００００００

００００００

００００００

００００００


12AXIS.MEMORY

OFFAB

Select 12 AXIS memory to adjust.

G.SAT -63׀0׀

63

Adjusts the saturation of color components in 12 AXIS matrix memory.• Not available when [12 AXIS

MEMORY] is set to [OFF].

G_Cy.SATCy.SATCy_B.SATB.SATB_Mg.SATMg.SATMg_R.SATR.SATR_Ye.SATYe.SATYe_G.SATG.PHASE -63

׀0׀

63

Adjusts the color phase of color components in 12 AXIS matrix memory.• Not available when [12 AXIS

MEMORY] is set to [OFF].

G_Cy.PHASECy.PHASECy_B.PHASEB.PHASEB_Mg.PHASEMg.PHASEMg_R.PHASER.PHASER_Ye.PHASEYe.PHASEYe_G.PHASE

HD.DTL/SKIN.DTL.(1/2)

→＊＊　ＨＤ　ＤＴＬ／ＳＫＩＮ　ＤＴＬ（１／２）　＊＊

ＤＥＴＡＩＬ　ＳＷＩＴＣＨＶ　ＤＥＴＡＩＬＨ　ＤＥＴＡＩＬＣＲＩＳＰＰＥＡＫＦＲＥＱＵＥＮＣＹＬＥＶＥＬＤＥＰＥＮＤＥＮＴＤＡＲＫ　ＤＥＴＡＩＬＳＯＵＲＣＥＣＬＩＰＫＮＥＥ　ＤＥＴＡＩＬＧＡＩＮ

ＯＮ２０２０１０

０（Ｒ＋Ｇ）／２

０（＋）　０（－）　０

（＋）　０（－）　０

８％１７．３


DETAIL.SWITCH OFFON

Enables or disables the HD DETAIL effect.

V.DETAIL 0׀

20׀

63

Adjusts the level of vertical detail.

H.DETAIL 0׀

20׀

63

Adjusts the level of horizontal detail.

CRISP 0׀

10׀

63

Sets the maximum amplitude of the very faint noise components that are removed from detail components.

PEAK.FREQUENCY

12.4/12.5/12.7/12.9/13.0/13.3/13.6/13.9/14.2/14.6/15.0/15.5/16.1/16.7/17.3/18.0/18.6/18.8/19.0/19.2/19.5/19.9/20.3/20.9/21.5/22.4/23.6/25.4/28.6/37.1

Selects the contour correction frequency band (boost frequency or peak frequency). It changes the contour width.

LEVEL.DEPENDENT

0%׀

8%׀

30%

Lowers the detail in dark areas. It adjusts the level.

DARK.DETAIL 0׀7

Boosts the detail in dark areas.

SOURCE (R+G)/2(G+B)/2

(2G+R+B)/4(3G+R)/4

RG

Selects the source signals for creating the detail components.

+CLIP 0׀

63

Limits the length of the overshoot areas of the detail edge components.

-CLIP 0׀

63

Limits the length of the undershoot areas of the detail edge components.

KNEE.DETAIL 0׀

39

Enhances knee detail.

20


21

Item Display Function+GAIN -31

׀0׀

31

Changes the detail gain level in + (up) direction

-GAIN -31׀0׀

31

Changes the detail gain level in - (down) direction

HD.DTL/SKIN.DTL.(2/2)

→＊＊　ＨＤ　ＤＴＬ／ＳＫＩＮ　ＤＴＬ（２／２）　＊＊

ＳＫＩＮ　ＤＥＴＡＩＬ　ＳＷＩＴＣＨＣＵＲＳＯＲ

ＳＫＩＮ　ＧＥＴ

ＣＲＩＳＰＰＨＡＳＥＷＩＤＴＨＳＡＴＵＭＥＭＯＲＹ　ＳＥＬＥＣＴ

ＡＢ

ＺＥＢＲＡ　ＳＷＩＴＣＨＥＦＦＥＣＴ　ＭＥＭＯＲＹ

ＯＦＦ

ＯＦＦＡ＋Ｂ

Ａ

００

００

００

００

ＮＯ�ＯＦＦ

ＯＮ／ＯＦＦＨ９６０

Ｖ２７０


SKIN.DETAIL.SWITCH

OFFON

Enables or disables control of skin tone detail in HDTV video output.

CURSOR OFFON

Enables or disables the position cursor that obtains the saturation and color phase information for controlling skin tone detail.

POS.H 1׀

960׀

1920

Sets horizontal cursor position.

POS.V 1׀

270.540

Sets vertical cursor position.

SKIN.GET NO?EXECUTECANCEL

Automatically obtains the saturation and color phase information from the cursor position.

NO?: Cancels operation.EXECUTE: Automatically obtains

saturation and color phase information from the cursor position.

CANCEL: Discards the saturation and

color phase information obtained from the cursor position.

MEMORY.SELECT

AB

Changes memory locations for saving the skin tone detail settings (CRISP, PHASE, WIDTH and SATURATION).

MEM.A.CLISP -63׀0׀

63

Removes very faint noise components from detail components in skin tone areas in memory bank A.

MEM.A.PHASE 0׀

359

Changes the color phase of skin tone areas in memory bank A in a range from 0 to 359 on a vector display.

Item Display FunctionMEM.A.WIDTH 0

׀255

Expands the width of skin tone areas in memory bank A in a range from 0 to 255.

MEM.A.SATU 0׀

255

Changes the saturation of skin tone areas in memory bank A in a range of 0 to 255.

MEM.B.CLISP -63׀0׀

63

Removes very faint noise components from detail components in skin tone areas in memory bank B.

MEM.B.PHASE 0׀

359

Changes the color phase of skin tone areas in memory bank B in a range of 0 to 359 on a vector display.

MEM.B.WIDTH 0׀

255

Expands the width of skin tone areas in memory bank B in a range from 0 to 255.

MEM.B.SATU 0׀

255

Changes the saturation of skin tone areas in memory bank B in a range from 0 to 255.

ZEBRA.SWITCH OFFAB

A+B

Adds a zebra pattern to the Y signals of the PM output to make areas subject to skin tone detail effects easily visible.

EFFECT.MEMORY

AB

A+B

Selects the memory bank to which skin tone detail effects will be added.

SD.DETAIL

→＊＊　ＳＤ　ＤＥＴＡＩＬ　＊＊

ＤＥＴＡＩＬ　ＳＷＩＴＣＨＶ　ＤＥＴＡＩＬＨ　ＤＥＴＡＩＬＣＲＩＳＰＰＥＡＫ１ＰＥＡＫ２ＬＥＶＥＬ　ＤＥＰＥＮＤＥＮＴＤＡＲＫ　ＤＥＴＡＩＬ

ＯＮ

ＯＦＦ

３

５％１

５０

３．１７Ｍ


DETAIL.SWITCH ONOFF

Enables or disables changes in contour enhancement (hard/soft) level of SDTV video output.

V.DETAIL 0׀3׀

63

Adjusts the amount of vertical detail.

H.DETAIL 0׀5׀

63

Adjusts the amount of horizontal detail.

CRISP 0׀

63

Sets the maximum amplitude of the very faint noise components that are removed from detail components.

PEAK1 1.89M/2.18M/2.56M/3.17M/4.0M/5.28M/

6.75M

Selects one of the two contour correction frequency bands (boost frequency or peak frequency). Changes the contour width.

PEAK2 OFF/1.89M/2.18M/2.56M/3.17M/4.00M/.5.28M/6.75M

Selects one of the two contour correction frequency bands (boost frequency or peak frequency). Changes the contour width.

20 21


Item Display FunctionLEVEL.DEPENDENT

0׀

5.%׀

30.%

Lowers the detail in dark areas. It adjusts the level.

DARK.DETAIL 0׀1׀5

SYSTEM.(1/2)

→＊＊　ＳＹＳＴＥＭ　（１／２）　＊＊

ＲＥＴＵＲＮ１ＲＥＴＵＲＮ２ＲＥＴＵＲＮ３ＲＥＴＵＲＮ４ＲＥＴＵＲＮ・ＤＥＬＡＹＤＯＷＮ　ＣＯＮＶＥＲＴ　ＭＯＤＥＵＰ　ＣＯＮＶＥＲＴ　ＭＯＤＥＨＤ　ＣＯＬＯＲ　ＢＡＲＰＡＴＨＯＳＤＩ３－４　ＯＵＴ

ＨＤ　ＳＤＩ１ＨＤ　ＳＤＩ１ＨＤ　ＳＤＩ１ＨＤ　ＳＤＩ１

ＮＯＲＭＡＬ

ＳＣＡＲＩＢ

ＯＦＦＰＭ

ＳＣ


RETURN1 HD.SDI1HD.SDI2

VBS

Sets the input allocations of return signal 1.


VBS



VBS



VBS


RETURN.·.DELAY

NORMALSHORT

Selects whether a RET display video will be delayed by 1 F (NORMAL) or by the shortest possible period (SHORT).

DOWN.CONVERT.MODE

SCSQLB

Selects the down-conversion system for video output from SD SDI and VBS.

UP.CONVERT.MODE

SCSQLB

Selects the up-conversion system for videos used as SD SDI and VBS return videos.

Item Display FunctionHD.COLOR.BAR FULL

BARS-1ARIB

BARS-2BARS-3BARS-4BARS-5BARS-6

Select the color bar signals to be output from the HD/SD SDI OUT connectors and VBS connector when “BAR” has been selected on the operation panel of the ROP.When they are output in VBS or SD format, color bars in HD format are output in the mode specified withDOWNCONVERT MODE.FULL: 75 % full field color barBARS-1: Color bar based on the

SMPTE standardARIB: ARIB multi-format color barBARS-2: Color bar based on the EIAJ

standardBARS-3: Split field color barBARS-4: 75 % full field color bar placed

in an area with a 4:3 aspect ratio.

(Displayed 40 % gray outside the area.)

BARS-5: Color bar based on the

SMPTE standard that is placed in an area with a 4:3 aspect ratio.


BARS-6: Color bar based on the EIAJ

standard that is placed in an area with a 4:3 aspect ratio.


PATHO OFFON

Select ON/OFF for the pathological signals.

SDI3-4.OUT NORMALPM

Selects the signals output from the 3rd and 4th HD/SD SDI signal output connectors on a CCU.

22


23

SYSTEM.(2/2)

→＊＊　ＳＹＳＴＥＭ　（２／２）　＊＊

ＨＤ　Ｈ　ＰＨＡＳＥＳＤ　Ｈ　ＰＨＡＳＥＳＤ－ＨＤ　Ｖ

ＭＩＣ１ＭＩＣ２

ＧＡＩＮＡＭＰ６０dB６０dB

０dB０dB

０Ｈ

００


HD.H.PHASE -1099׀0׀

1099.(59.94.Hz)

-1319׀0׀

1319.(50Hz)

Adjusts the horizontal phase of HD SD video for the genlock reference phase.

SD.H.PHASE -857׀0׀

857.(59.94Hz)

-863׀0׀

863.(50Hz)

Adjusts SD horizontal sync phase.

SD-HD.V 0HADVANCE

0H_SD_DLAY.

Set the vertical phase of the HDTV output in relation to the SDTV output.0H: Sets the vertical phase to the

same phase.ADVANCE: When the field frequency is

59.94 Hz, the phase advance is 90H.

When the field frequency is 50 Hz, the phase advance is 75H.

0H_SD_DLAY: The SDTV signals are delayed

and set in-phase with the HDTV signals.

• When the setting of this item is set to “0H” or “ADVANCE” while the field frequency is 50 Hz, images in SD format are delayed by 1 frame + 75 lines only when letterbox is selected for DOWNCONVERT MODE. For the relationship with the sync phase, refer to Operating Instructions <Operations and Settings> of AK-HCU200.

ADVANCE:. 59.94Hz→90H. 50Hz→75H

MIC1.GAIN 20dB40dB60dB

Performs coarse adjustment of MIC1 gain.

Item Display FunctionMIC1.AMP -20dB

׀0׀

20dB

Makes fine adjustments of the MIC1 gain.

(in.1.dB.increments)

MIC2.GAIN 20dB40dB60dB

Makes coarse adjustments of MIC2 gain.

MIC2.AMP -20dB׀0׀

20dB

Makes fine adjustments of MIC2 gain.

(in.1.dB.increments)

FUNCTION

→＊＊　ＦＵＮＣＴＩＯＮ　＊＊

ＡＬＣ　ＬＥＢＥＬＡＬＣ　ＳＰＥＥＤＡＬＣ　ＷＩＮＤＯＷＡＬＣ　ＰＥＡＫＡＬＣ　ＲＡＮＧＥ

ＡＳＵ　ＳＥＴＵＰＡＳＵ　ＲＥＦ　ＦＩＬＥＡＳＵ　ＭＡＳＴＥＲ　ＰＥＤ　ＳＥＴＡＳＵ　ＦＩＬＴＥＲ

ＴＡＬＬＹ　ＧＵＡＲＤ

５０１５１

６０ＮＯＲＭＡＬ

ＯＵＴ　ＦＵＬＬＦＡＣＴＯＲＹ

２．０％ＲＥＦ

ＯＦＦ


ALC.LEVEL 0׀

50׀

100

Adjusts the auto iris level of the lens iris.

ALC.SPEED 1׀

15׀

25

Sets the feedback speed of the auto iris.Feedback speed drops as the numbers increase.

ALC.WINDOW 1׀4

Sets the image detection area window for the auto iris.

ALC.PEAK 0׀

60׀

100

Sets the ratio between the average and peak values of auto iris image detection.

ALC.RANGE NORMAL3/42/41/4

Sets the correction range for adjustments of the iris level using the IRIS knob to move the iris lever <IRIS ( )> in auto iris mode.

ASU.SETUP OUT.FULLOUT.EASY

Selects the auto setup mode setting.

ASU.REF.FILE FACTORYUSER1USER2USER3

Selects the file to be referenced when auto setup has been started.

ASU.MASTER.PED.SET

0.0%׀

2.0%׀

7.5%

Sets the position where the master pedestal is to be converged when auto setup is started.

22 23


Item Display FunctionASU.FILTER REF

CURRENTSets the operation of the ND filter when auto setup is started.

REF: The filter stored in the

reference file is used when operation starts.

CURRENT: Auto setup starts at the filter

position made prior to startup.

TALLY.GUARD OFFON

At the ON setting, this function disables automatic ASU, AWB, ABB operation while the tally is ON.

LENS.FILE/EDIT.(1/2)

→＊＊　ＬＥＮＳ　ＦＩＬＥ／ＥＤＩＴ（１／２）　＊＊

ＭＯＤＥＦＩＬＥ　ＮＯ

ＦＩＬＥ　ＮＡＭＥ

ＥＸＥＣＵＴＥ

ＬＯＡＤＯＦＦ

ＮＯ？


MODE LOADSTORE

Saves current lens files in the camera (STORE) or loads (LOAD) lens files stored in the camera.

FILE.NO. zWhen [LOAD] is selected as [MODE]

OFF1׀

32 zWhen [STORE] is selected as [MODE]

1׀

32

Selects the lens file number.

FILE.NAME Up.to.8.characters

Use to enter the file name.• It is disabled when [LOAD] is

selected in [MODE].

Allowable.characters0.-.9,.A.-.Z,.a.-.z,.._.(under.bar),..(space)

EXECUTE YES?NO?

Executes processes selected in MODE.

LENS.FILE/EDIT.(2/2)

→＊＊　ＬＥＮＳ　ＦＩＬＥ／ＥＤＩＴ（２／２）　＊＊

ＥＸＴＥＮＤＥＲＦＩＬＥ

ＦＬＡＲＥＧＡＩＮ

ＲＧＢ

ＳＴＯＲＥ？ＣＡＮＣＥＬ？

Ｘ１．０

Ｒ－－－

－－

－－－－－－－－－－－－

－－

ＧＢ

ＨＳＡＷＨＰＡＲＡＶＳＡＷＶＰＡＲＡ


EXTENDER x.1.0x.2.0

Sets the current magnification of the lens extender.

FILE Displays the number and name of currently loaded lens files.

FLARE.R -100׀0׀

100

Sets lens R flare.

FLARE.G -100׀0׀

100

Sets lens G flare.

FLARE.B -100׀0׀

100

Sets lens B flare.

GAIN.R -100׀0׀

100

Sets lens R gain.

GAIN.B -100׀0׀

100

Sets lens B gain.

R.HSAW -100׀0.׀

100

Sets lens white shading.

R.HPARAR.VSAWR.VPARAG.HSAWG.HPARAG.VSAWG.VPARAB.HSAWB.HPARAB.VSAWB.VPARASTORE? YES?

NO?Saves R/G/B gain, R/G/B flare and white shading settings to the displayed file.

CANCEL? YES?NO?

Discards R/G/B gain, R/G/B flare and white shading settings and restores the original lens files.

24 25

Data.handled.in.the.studio.camera.system

The following shows the data handled in the studio camera system.The AK-HRP200 (ROP) memory card stores camera and CCU data.

AK-HC3800 (Camera)

LENS 1

LENS 32

LENS 1

LENS 32

USER 1

USER 2

USER 3

USER 2

USER 3

SCENE 1

SCENE 2

SCENE 3

SCENE 4

USER 1

USER 2

USER 3

SCENE 1

SCENE 2

SCENE 3

SCENE 4

SCENE 1

SCENE 2

SCENE 3

SCENE 4

AK-HCU200 (CCU) AK-HRP200 (ROP)

USER 1

Operation data(for camera)

Operation data(for CCU)

Scene file(for camera)

Scene file(for CCU)

Memory card

Name Quantity Description Data.R/W Memory.card.R/W

Lens.file.(LENS) 1 to 32 This data is used by video engineers (VE) to correct the characteristics specific to the lenses and is managed by the camera. It can be saved and read by operation on the ROP. It can also be saved and read to/from the memory card on the ROP.For a list of data, refer to the Operating Instructions for AK-HRP200G.

ROP ROP

Scene.file.(SCENE) 1 to 4 This data for creating pictures is handled mainly by video engineers (VE) and is managed by the camera. It can be saved and read by operation on the ROP. It can also be saved and read to/from the memory card on the ROP.For a list of data, refer to the Operating Instructions for AK-HRP200G.

ROP ROP

User.file.(USER) 1 to 3 This system setting data consists of scene file managed by the camera, camera operation data, and scene file managed by the CCU. It can be saved and read by operation on the ROP. It can also be saved and read to/from the memory card on the ROP.

ROP ROP

�� .Initializing.data

Name

How.to.initialize.dataHold down <TALLY/CALL> while pressing <SHIFT> and <SCENE4> on the ROP to initialize.(When initialization completes, turn off the CCU.)

Initializing using camera, CCU and ROP functions

Scene.files : Are initialized *2 -

User.files : Are initialized *2 -

Lens.files : Are initialized -

Camera.settings : Are initialized *3 -

CCU.settings : Are not initialized : Choose [SYSTEM] > [INTIALIZE] in the CCU menu to initialize. *4

ROP.settings : Are not initialized : Use [16] in the ROP setup menu to initialize.

*1 Includes [SD DETAIL] settings of scene files and user files.*2 [SD DETAIL] settings are not initialized.*3 Frame frequency is also initialized.

When a camera image does not appear after initialization, check whether the frame frequency matches the (frequency) of the CCU [CCU MODE].*4 [Frame frequency] of [CCU MODE] is also initialized.

When a camera image does not appear after initialization, check whether [CCU MODE] matches the frame frequency of the camera.

24 25

Data.item.list

��Camera.(menu.list).zOPERATION

Menu Item Adjustment.range Default.valueProtected.settings

SCENE1.to.4

USER1.to.3

LENS1.to.32

MARKER SIDE MODULE LEVEL 0 to 15 0

ZONE MARK OFF, 4:3, 13:9, 14:9, 15:9, 16:9 OFF

SAFETY AREA - -

MODE TYPE1, TYPE2 TYPE1

SETTING 80% to 100%OFF, 4:3, 13:9, 14:9, 15:9, 16:9

80% (MODE TYPE1)

OFF (MODE TYPE2)

CENTER MARK OFF, 1 to 4 OFF

MARKER LEVEL 50%, 60%, 70%, 80%, 90%, 100%

100%

USER BOX ON, OFF OFF

HORIZONTAL POSITION -50 to 50 0

VERTICAL POSITION -50 to 50 0

WIDTH 0 to 100 50

HEIGHT 0 to 100 50

VIEW FINDER SETTING VIEW FINDER DETAIL 0 to 23 6

RETURN SIGNAL - -

PEAK FREQUENCY LOW, MID, HIGH MID

OFFSET GAIN 0 to 5 0

CRISP 0 to 15 10

INDICATOR1 FOCUS ON, OFF OFF

ZOOM ON, OFF OFF

EXTENDER ON, OFF OFF

DIGITAL EXTENDER ON, OFF OFF

F NUMBER ON, OFF OFF

MASTER GAIN ON, OFF OFF

FILTER ON, OFF OFF

SHUTTER ON, OFF OFF

5600K ON, OFF OFF

WHITE CHANNEL ON, OFF OFF

DRS ON, OFF OFF

CAC ON, OFF OFF

INDICATOR2 FAN ON, OFF OFF

AUDIO LEVEL ON, OFF OFF

OPTICAL LEVEL ON, OFF OFF

RETURN SELECT ON, OFF OFF

STATUS ON, OFF OFF

STATUS(AUTO) ON, OFF OFF

CAMERA MODE ON, OFF OFF

SYSTEM MODE ON, OFF OFF

SWITCH MODE GRIP RET RET A, RET B, PTT RET A

GRIP PTT RET A, RET B, PTT PTT

LENS VTR RET A, RET B, PTT, INH RET B

LENS RET RET A, RET B RET A

EXTERNAL RETURN1 RET A, RET B, D.EXT RET A

EXTERNAL RETURN2 RET A, RET B, D.EXT RET B

EXTERNAL RETURN3 RET A, RET B, D.EXT RET B

USER SWITCH1 RET A, RET B, PTT, DISP, MARK, D.EXT

RET A


PTT


PTT

26

Data.item.list. (continued)

27


SCENE1.to.4

USER1.to.3

LENS1.to.32

RETURN SETTING RETURN MODE NORM, TOGGLE, SEQ. NORM

RETURN SELECT - -

RETURN A 1, 2, 3, 4 1

RETURN B 1, 2, 3, 4 2

ID SETTING - -

RETURN 1 "RET1 "(5 characters) RET1




SETTING CALL TALLY OFF, R, T, R&T OFF

HD-SDI2 OUT MAIN, VF, RET VF

HD-SDI2 POWER ACTIVE, SAVE ACTIVE

FAN POWER ON, OFF ON

ID CHARACTER (10 characters) -

!LED EXTENDER ON, OFF OFF

MASTER GAIN ON, OFF OFF

SHUTTER ON, OFF OFF

GAMMA OFF ON, OFF OFF

BLACK GAMMA ON, OFF OFF

MIC/INCOM SETTING MIC1 - -

GAIN 20dB, 40dB, 60dB 60dB

AMP –20dB to 20dB 0dB

MIC2 - -

GAIN 20dB, 40dB, 60dB 60dB

AMP –20dB to 20dB 0dB

INCOM - -

MIC TYPE DYN, ECM, CBN DYN

MIC GAIN –12dB to 12dB 0dB

MIC POWER ON, OFF OFF

SIDE TONE OFF, –36dB to 0dB -6dB

PGM MIX ON, OFF ON

26 27


.zMAINTENANCE

Menu Item Adjustment.range Default.value.Protected.settings

SCENE1.to.4

USER1.to.3

LENS1.to.32

SD CARD R/W READ SELECT 1 to 8 1

READ YES, NO NO

WRITE SELECT 1 to 8 1

WRITE YES, NO NO

CARD CONFIG YES, NO NO

CAC ADJUST CAC CONTROL ON, OFF ON

CAC FILE DELETE YES, NO NO

CAC FILE NUMBER 1 to 32 1

TITLE SCROLL 1 to 25 1

CAC FILE CARD READ CARD FILE SELECT 1 to 32 1

READ YES, NO NO

DELETE YES, NO NO

TITLE READ YES, NO NO


FILE READ TITLE - -

YES - -

NO(CANCEL) - -

MEM STORE NO EMPTY, 1 to 32 EMPTY


AUTO SET UP FILTER REF/CURRENT REF

SETUP MODE FULL/EASY FULL

REFERENCE FILE FACTORY, USER1, USER2, USER3

FACTORY

MASTER PED TARGET 0.0% to 7.5% 2.0%

AUTO SET UP EXECUTE YES, NO NO

TALLY GUARD ON, OFF OFF

COLOR BAR SMPTE, FULL BAR, ARIB FULL BAR

DIAGNOSTIC PULSE (Displays PULSE FPGA version) -

CAM (Displays CAM FPGA version) -

AVIO (Displays AVIO FPGA version) -

CAMERA SOFT (Displays CAMERA software version)

-

CAMERA TABLE (Displays CAMERA table version)

-

HOURS METER [h] - -

HEAD 0 to 65000 -

FAN 0 to 65000 -

SYSTEM FORMAT 59.94i, 50i 59.94i*1

50i*2

SCAN REVERSE ON, OFF OFF

DNR ON, OFF ON

SYSTEM FILE DATA - -

WRITE CARD YES, NO NO

GAIN MAX LIMIT 12dB, 36dB 12dB

UPDATE YES, NO NO

*1 AK-HC3800G/GS*2 AK-HC2500MC/MS

28


29

��CCU.(menu.list)

Menu Submenu Item Adjustment.range Default.valueProtected.settings

SCENE1.to.4

USER1.to.3

LENS1.to.32

OPERATION SETTING1 CCU MODE 1080/59.94i 1080/50i

59.94Hz *1 : 1080/59.94i50Hz *2 : 1080/50i

SDI RETURN1 HD SD

HD

SDI RETURN2 HD SD

HD

SDI OUTPUT1&2 HD SD

HD

SDI OUTPUT3&4 HD SD

HD

SDI OUTPUT3&4 NORMAL/PM

NORMAL PM

PM

COMPOSITE NORMAL/PM

NORMAL PM

PM

SETTING2 FS DELAY NORMAL SHORT

NORMAL

HD BAR SELECT FULLBARS-1ARIBBARS-2BARS-3BARS-4BARS-5BARS-6

ARIB

BAR LPF OFF 3TAP 5TAP 7TAP 9TAP

7TAP

BAR USER1 75%WHITE 100%WHITE +I_SIGNAL -I_SIGNAL

75%WHITE

BAR USER2 0%BLACK +Q_SIGNAL

0%BLACK

SETUP 7.5% ON OFF

OFF

PATHO ON OFF

OFF

HD / SD PHASE HD H PHASE 59.94Hz: -1099 to 109950Hz: -1319 to 1319

59.94Hz: 0 50Hz: 0

SD H PHASE 59.94Hz: -857 to 857 50Hz: -863 to 863

59.94Hz: 0 50Hz: 0

SD-HD V 0H, ADVANCE, 0H_SD_DLAY* ADVANCE: 59.94Hz→90H, 50Hz→75H

0H

BAR ID BAR ID SWITCH ON OFF

OFF

BRIGHTNESS 0 to 100% (in 10% increments)

100%

ID1 POSITION Row: 0 to 5 Column: 0 to 15

Row: 0 Column: 0

ID1 Up to 16 characters ##

ID2 POSITION Row: 0 to 5 Column: 0 to 15

Row: 1 Column: 0

ID2 Up to 16 characters ##

OFFSET Horizontal: 0 to 89 Vertical: 0 to 79

Horizontal: 0 Vertical: 0

*1 AK-HCU200/S, AK-HCU200P/PS, AK-HCU200E/ES*2 AK-HCU200MC/MS

28 29



SCENE1.to.4

USER1.to.3

LENS1.to.32

OPERATION INCOM/MIC 4W/RTS IN Level -40.0 to 20.0 dB (in 0.5 dB increments)

0 dB

4W/RTS OUT Level -40.0 to 20.0 dB (in 0.5 dB increments)

0 dB

RTS Cancel -40.0 to 31.5 dB(in 0.5 dB increments)

0 dB

GAIN PGM 0dB 20dB

0 dB

MIC1 LEVEL -40.0 dB to 20.0 dB (in 0.5 dB increments)

0 dB

MIC2 LEVEL -40.0 dB to 20.0 dB (in 0.5 dB increments)

0 dB

CM/DM CM DM

DM

CCU INCOM MIC -40.0 dB to 12.0 dB (in 0.5 dB increments)

0 dB

CCU SIDE TONE -40.0 dB to 0 dB (in 0.5 dB increments)

-6 dB

MAINTENANCE START UP CAM POWER OFF ON REMOTE

REMOTE

VF POWER OFF ON REMOTE

REMOTE

ANALOG GAIN COMPOSITE -50 to 50 0

ND NAME ND1 NAME 4 characters 1

ND2 NAME 4 characters 2



NETWORK IP ADDRESS 192.168.0.20

SUB NETMASK 255.255.255.*** to255.255.255.***(Range: 0, 128, 192, 224, 240, 248, 252, 254, 255)

0

DEFAULT GATEWAY 192.168.0.1

PORT 1 to 65535(However, the following numbers are excluded.) -20/21 (FTP) -25 (SMTP) -42/53 (DNS) -69 (tFTP) -23 (telnet) -110/995 (POP3) -123 (NTP) -67/68 (BOOTP/DHCP) -10669/10670 (BOOTP) -161/162 (SNMP)

80

MAC ADDRESS Displayed only

VERSION SOFTWARE Displayed only

HARDWARE FPGA1 Displayed only



30


31


SCENE1.to.4

USER1.to.3

LENS1.to.32

MAINTENANCE PM VIEW SETTING CAMERA No. ON OFF

ON

CAM MOD ON OFF

ON

SCENE FILE No. ON OFF

ON

SHUTTER ON OFF

ON

ND FILTER ON OFF

ON

GAIN ON OFF

ON

EXTENDER INFO ON OFF

ON

IRIS ON OFF

ON

IRIS LEVEL ON OFF

ON

PM OPERATION STATUS

STATUS DISPLAY TIME 0 2 4

4

MASTER GAIN ON OFF

ON

SHUTTER ON OFF

ON

LENZE EXTENDER ON OFF

ON

FILTER ON OFF

ON

SCENE FILE ON OFF

ON

REF LOAD ON OFF

ON

AUTO OPERATION STATUS

ON OFF

ON

SYSTEM INITIALIZE NO? YES?

NO?

SD CARD DOWNLOAD DATA BACK UP

NO? YES?

NO?

DOWNLOAD DATA LOG NO? YES?

NO?

UPLOAD DATA BACKUP NO? YES?

NO?

UPDATE NO? YES?

NO?

CARD FORMAT NO? YES?

NO?

30 31


��ROP.(menu.list)


SCENE1.to.4

USER1.to.3

LENS1.to.32

SHADING(WHITE) WHITE SHADING SWITCH OFF/ON ON

H SAW R -100 to 100 0

H SAW G -100 to 100 0

H SAW B -100 to 100 0

H PARA R -100 to 100 0

H PARA G -100 to 100 0

H PARA B -100 to 100 0

V SAW R -100 to 100 0

V SAW G -100 to 100 0

V SAW B -100 to 100 0

V PARA R -100 to 100 0

V PARA G -100 to 100 0

V PARA B -100 to 100 0

PEDESTAL/FLARE/GAIN FLARE SWITCH OFF/ON ON

MASTER PEDESTAL -99 to 99 0

PEDESTAL R -800 to 800 0

PEDESTAL G -800 to 800 0

PEDESTAL B -800 to 800 0

FLARE R -100 to 100 0

FLARE G -100 to 100 0

FLARE B -100 to 100 0

GAIN R -800 to 800 0

GAIN B -800 to 800 0

GAMMA/BLACK.GAMMA GAMMA SWITCH OFF/ON ON

GAMMA R -75 to 75 (VIDEO_REC)-60 to 60 (FILMLIKE1 to 3)

0

GAMMA M 0.300 to 0.750 (VIDEO_REC)0.3000 to 0.7500 (FILMLIKE1 to 3)

0.450

GAMMA B -75 to 75 (VIDEO_REC)-60 to 60 (FILMLIKE1 to 3)

0

BLACK GAMMA SWITCH OFF/ON OFF

BLACK GAMMA R -20 (black compression) to 20 (black expansion)

0

BLACK GAMMA M -32 (black compression) to 32 (black expansion)

0

BLACK GAMMA B -20 (black compression) to 20 (black expansion)

0

DRS SWITCH OFF/ON OFF

EFFECT DEPTH 1 to 5 1

PRE-CORRECTION 4.0/4.5/5.0 4.5

CINEMA GAMMA CINEMA GAMMA SWITCH OFF/ON OFF

CINEMA TYPE VIDEO/FILM VIDEO

CINEMA GAMMA SEL When [CINEMA TYPE] is set to [VIDEO]VIDEO_REC/FILMLIKE1/FILMLIKE2/FILMLIKE3When [CINEMA TYPE] is set to [FILM]FILM_REC (fixed)

VIDEO_REC

BLACK STRETCH LEVEL 0 to 30 0

DYNAMIC LEVEL 200%/300%/400%/ 500%

200%

KNEE POINT 30 to 90 30

KNEE SLOPE 150%/200%/250%/ 300%/350%/400%/ 450%/500%/550%/ 600%

150%

32


33


SCENE1.to.4

USER1.to.3

LENS1.to.32

KNEE/WHITE CLIP KNEE SWITCH OFF/ON ON

POINT R -20 to 20 0

POINT M 80.0% to 110.0% 95.0%

POINT B -20 to 20 0

SLOPE R -31 to 31 0

SLOPE M 0 to 199 130

SLOPE B -31 to 31 0

WHITE CLIP SWITCH OFF/ON ON

CLIP R -15 to 15 0

CLIP M 80% to 109% 109%

CLIP B -15 to 15 0

HI COLOR OFF/ON OFF

MATRIX (1/2) PRESET NORMAL/EBU/NTSC NORMAL

MATRIX SWITCH OFF/ON OFF

MEMORY OFF/A/B A

R-G -63 to 63 0

R-B -63 to 63 0

G-R -63 to 63 0

G-B -63 to 63 0

B-R -63 to 63 0

B-G -63 to 63 0

MATRIX (2/2) 12AXIS MEMORY OFF/A/B A

G SAT -63 to 63

Not available when [12 AXIS MEMORY] is set to [OFF].

0

G_Cy SAT 0

Cy SAT 0

Cy_B SAT 0

B SAT 0

B_Mg SAT 0

Mg SAT 0

Mg_R SAT 0

R SAT 0

R_Ye SAT 0

Ye SAT 0

Ye_G SAT 0

G PHASE -63 to 63

Not available when [12 AXIS MEMORY] is set to [OFF].

0

G_Cy PHASE 0

Cy PHASE 0

Cy_B PHASE 0

B PHASE 0

B_Mg PHASE 0

Mg PHASE 0

Mg_R PHASE 0

R PHASE 0

R_Ye PHASE 0

Ye PHASE 0

Ye_G PHASE 0

32 33



SCENE1.to.4

USER1.to.3

LENS1.to.32

HD DTL/SKIN DTL (1/2) DETAIL SWITCH OFF/ON ON

V DETAIL 0 to 63 20

H DETAIL 0 to 63 20

CRISP 0 to 63 10

PEAK FREQUENCY 12.4/12.5/12.7/12.9/ 13.0/13.3/13.6/13.9/ 14.2/14.6/15.0/15.5/ 16.1/16.7/17.3/18.0/ 18.6/18.8/19.0/19.2/ 19.5/19.9/20.3/20.9/ 21.5/22.4/23.6/25.4/ 28.6/37.1

17.3

LEVEL DEPENDENT 0 to 30% 8%

DARK DETAIL 0 to 7 0

SOURCE (R+G)/2, (G+B)/2, (2G+R+B)/4, (3G+R)/4, R, G

(R+G)/2

+CLIP 0 to 63 0

-CLIP 0 to 63 0

KNEE DETAIL 0 to 39 0

+GAIN -31 to 31 0

-GAIN -31 to 31 0

HD DTL/SKIN DTL (2/2) SKIN DETAIL SWITCH OFF/ON OFF

CURSOR OFF/ON OFF

POS H 1 to 1920 960

POS V 1 to 540 270

SKIN GET NO?: Cancel the operationEXECUTE: Automatically obtains saturation and color phase information from the cursor position.CANCEL: Discards the saturation and color phase obtained from the cursor position.

NO?

MEMORY SELECT A/B A

MEM A CLISP

-63 to 63 0

MEM A PHASE

0 to 359 0

MEM A WIDTH

0 to 255 0

MEM A SATU

0 to 255 0

MEM B CLISP

-63 to 63 0

MEM B PHASE

0 to 359 0

MEM B WIDTH

0 to 255 0

MEM B SATU

0 to 255 0

ZEBRA SWITCH OFF/A/B/A+B OFF

EFFECT MEMORY A/B/A+B A+B

SD DETAIL DETAIL SWITCH ON/OFF ON

V DETAIL 0 to 63 3

H DETAIL 0 to 63 5

CRISP 0 to 63 0

PEAK1 1.89M/2.18M/2.56M/ 3.17M/4.0M/5.28M/ 6.75M

3.17M

PEAK2 OFF/1.89M/2.18M/ 2.56M/3.17M/4.00M/ 5.28M/6.75M

OFF

LEVEL DEPENDENT 0 to 30% 5

DARK DETAIL 0 to 5 1

34


35


SCENE1.to.4

USER1.to.3

LENS1.to.32

SYSTEM (1/2) RETURN1 HD SDI1/HD SDI2/VBS HD SDI1

RETURN2 HD SDI1/HD SDI2/VBS HD SDI2



RETURN · DELAY NORMAL/SHORT NORMAL

DOWN CONVERT MODE SC/SQ/LB SC

UP CONVERT MODE SC/SQ/LB SC

HD COLOR BAR FULL/BARS-1/ARIB/BARS-2/BARS-3/BARS-4/BARS-5/BARS-6

ARIB

PATHO OFF/ON OFF

SDI3-4 OUT NORMAL/PM PM

SYSTEM (2/2) HD H PHASE -1099 to 1099 (59.94Hz)-1319 to 1319 (50Hz)

0

SD H PHASE -857 to 857 (59.94Hz)-863 to 863 (50Hz)

0

SD-HD V 0H/ADVANCE/ 0H_SD_DLAYADVANCE: 59.94Hz→90H 50Hz→75H

0H

MIC1 GAIN 20dB/40dB/60dB 60dB

MIC1 AMP -20 dB to 20 dB in 1 dB increments

0

MIC2 GAIN 20dB/40dB/60dB 60dB

MIC2 AMP -20 dB to 20 dB in 1 dB increments

0

FUNCTION ALC LEVEL 0 to 100 50

ALC SPEED 1 to 25 15

ALC WINDOW 1 to 4 1

ALC PEAK 0 to 100 60

ALC RANGE NORMAL, 3/4, 2/4, 1/4 NORMAL

ASU SETUP OUT FULL/OUT EASY OUT FULL

ASU REF FILE FACTORY/USER1/USER2/USER3

FACTORY

ASU MASTER PED SET 0.0% to 7.5% 2.0%

ASU FILTER REF: The filter set in the reference file is used at startup.CURRENT: Auto setup starts at the filter position made prior to startup.

REF

TALLY GUARD OFF/ON OFF

LENS FILE/EDIT (1/2) MODE LOAD/STORE LOAD

FILE NO. When [LOAD] is selectedOFF/1 to 32When [STORE] is selected1 to 32

OFF

FILE NAME Up to 8 characters when [STORE] is selected Allowable characters 0 to 9, A to Z, a to z, _ (underscore), (space)It is disabled when [LOAD] is selected in [MODE].

-

EXECUTE YES? / NO? NO?

34 35



SCENE1.to.4

USER1.to.3

LENS1.to.32

LENS FILE/EDIT (2/2) EXTENDER x1.0/x2.0 x1.0

FILE -

FLARE R -100 to 100 0

FLARE G -100 to 100 0

FLARE B -100 to 100 0

GAIN R -100 to 100 0

GAIN B -100 to 100 0

R HSAW -100 to 100 0

R HPARA -100 to 100 0

R VSAW -100 to 100 0

R VPARA -100 to 100 0

G HSAW -100 to 100 0

G HPARA -100 to 100 0

G VSAW -100 to 100 0

G VPARA -100 to 100 0

B HSAW -100 to 100 0

B HPARA -100 to 100 0

B VSAW -100 to 100 0

B VPARA -100 to 100 0

STORE? YES? / NO? NO?

CANCEL? YES? / NO? NO?

��ROP.(panel.operations)

Item Adjustment.range Default.valueProtected.settings

SCENE1.to.4

USER1.to.3

LENS1.to.32

5600K ON/OFF OFF

MATRIX ON/OFF OFF

SKIN DTL ON/OFF OFF

KNEE OFF ON/OFF ON

DTL OFF ON/OFF ON

ND 1 to 4 1

M.GAIN -3 to 12 (in 3 dB steps)18, 27, 36• Depends on camera setting.

0

SHUTTER ON/OFF OFF

at 59.94 Hz STEP: 1/100 to 1/2000SYNCRO: 60.0 to 250 at 50 Hz STEP: 1/60 to 1/2000 SYNCRO: 50.0 to 250

1/100 (59.94Hz)

1/60 (50Hz)

AUTO IRIS ON/OFF OFF

36 37

Index

CCamera menu ...................................................................................... 25Camera number ...................................................................................... 7CCU menu ........................................................................................... 28CINEMA-GAMMA ................................................................................ 17

EError display ........................................................................................ 13

FFormat (memory card) ......................................................................... 11FUNCTION .......................................................................................... 22

GGAMMA/BLACK.GAMMA .................................................................... 17

HHD DTL/SKIN DTL ........................................................................ 19, 20

IInitialize ................................................................................................ 11

KKNEE/WHITE CLIP ............................................................................. 18

LLENS FILE/EDIT ................................................................................. 23

MMATRIX ......................................................................................... 18, 19

OOptional accessory .............................................................................. 10

PPEDESTAL/FLARE/GAIN ................................................................... 16Protective panel ............................................................................. 10, 11

RROP configuration file ............................................................................. 9

Load ............................................................................................ 10Save ............................................................................................ 10

ROP menuList ............................................................................................... 31Operation ..................................................................................... 14Setting ......................................................................................... 16

SSave .................................................................................................. 8, 9

Load .......................................................................................... 8, 9Protective panel for transportation ................................................. 8Warning .......................................................................................... 9

Save unit data ...................................................................................... 12Scene file ................................................................................................ 7

Load ............................................................................................... 7Save ............................................................................................... 7

SD DETAIL .......................................................................................... 20Set 7-segment display brightness ...................................................... 11Set buzzer ........................................................................................... 10Set display brightness ........................................................................ 12Set LED display brightness ................................................................ 11Setup mode ............................................................................................ 4SHADING(WHITE) .............................................................................. 16Standard accessories .......................................................................... 11SYSTEM ........................................................................................ 21, 22

UUpgrade .............................................................................................. 12

36 37

Memo

Web Site: http://panasonic.net

プロフェッショナルAVビジネスユニット〒 571-8503　大阪府門真市松葉町 2 番 15 号 ☎ (06) 6901－1161

©Panasonic Corporation 2012

Remote Operation Panel AK-HRP200G - Panasonic USA · 2012. 11. 7. · CC SHT SYNC SELECT SAVE/LOAD...

Documents

Transcript of Remote Operation Panel AK-HRP200G - Panasonic USA · 2012. 11. 7. · CC SHT SYNC SELECT SAVE/LOAD...