Register of Mining Standards - سازمان نظام ...ime.org.ir/ad/os261/bergverze.pdf ·...

Register of Mining Standards

FABERG Normenausschuss Bergbauim DIN Deutsches Institut für Normung e.V.

Published by

2015-02dated

Contact Hans Georg [email protected]

of 44FABERG Normenausschuss Bergbau

Normenausschuss Bergbau (FABERG) is an agency of DIN Deutsches Institut für Normung e.V., Berlin. As a joint establishment of the German mining industry, it is supported by Vereinigung Rohstoffe und Bergbau e.V., Berlin and managed by a governing body. From a management and staff point of view, it is associated with DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V. of Essen.FABERG is responsible for national standardisation in the field of mining and acts as a representative for this field in European (CEN) *) and international (ISO) **) standardisation efforts, supporting the introduction of standards in its specialised field for any practice affected by these and is instrumental in establishing the German standards system. An association representing the interests of the mining industry was formed as early as at the end of the 1800s – as a joint effort of mines in the German Ruhr area – also dealing with issues of standardisation and recommending to its member companies the use of specific pipes and underground rail systems. After World War I, a committee was formed, dealing with standardisation on behalf of the coal mining industry in the German Rhineland and Westphalia. It was realised at an early date that standardisation involving the entire mining industry would be more effective and useful. This lead to the foundation of Fachnormenausschuss für den Bergbau (FaBerg) on November 28th, 1922 at Hannover.Whereas during the first years of FABERG’s existence, dimensional and type standards were primarily set up, these were increasingly followed by quality and demand-based standards. Personal safety equipment, too, was subject to standardisation at an early date.

In 1955, during the ISO General Assembly at Stockholm, the foundation of a “Mining” technical committee - ISO/TC 82 – was resolved, management of which was transferred to FABERG. In addition to this, FABERG is responsible for German representation in ISO/TC 27 "Solid Mineral Fuels".Within the scope of its CEN work delegated by the EU, FABERG was allocated the CEN/TC 196/WG 3 "Hydraulically Powered Support“ and CEN/TC 305/WG 5 "Equipment and Protective Systems for Mining" Secretariat.FABERG co-operates with other standards committees of DIN, CEN and ISO at national, European and international level, in order to represent the interests of the mining industry.The Register of Standards comprises ISO standards of TC 27 "Solid Mineral Fuels" and of TC 82 "Mining".The register also includes Operating Recommendations for Mining (Bergbau-Betriebsblätter). These are recommendations set up by professionals, based on the same principles, which are mandatory for wording DIN standards. Users of these recommendations are subject to examining whether any arrangements recommended in these are adequate. Bergbau-Betriebsblätter are published by DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V. Bergbau-Betriebsblätter may be ordered from DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V., FABERG, Normenausschuss Bergbau, Wilhelmstraße 98, 44649 Herne, Telefon +49 2325 5832456.The Standards Inspection Office of DIN in FABERG is available for inspection of any national DIN standards. Research work may be conveniently performed through the Perinorm database of BSI, AFNOR and DIN and ISO/IEC, CEN/CENELEC standards.

Opening times of Standards Inspection Office (Normenauslegestelle):Monday to Friday: 8.00 a.m. to 12.00 a.m. and 1.00 p.m. to 3.30 p.m.---------*) CEN = Comité Européen de Normalisation**) ISO = International Organization for Standardization

Foreword


The numbers after the titles of DIN standards and DIN drafts in brackets are price groups (dated 2014-01-01); they correspond with the following prices (paper version):

Preisgr. EUR Preisgr. EUR Preisgr. EUR 01 16,70 19 130,20 37 320,30 02 24,60 20 135,90 38 347,40 03 24,60 21 142,10 41 369,80 04 24,60 22 147,50 42 391,90 05 34,90 23 153,00 51 430,50 06 42,40 24 159,30 52 496,60 07 49,50 25 164,50 08 57,00 26 170,40 09 64,10 27 176,60 10 71,10 28 182,40 11 78,30 29 188,00 12 85,80 30 193,50 13 92,70 31 198,90 14 99,80 32 217,80 15 107,10 33 233,00 16 113,20 34 252,20 17 118,80 35 265,80 18 124,20 36 293,10

Further information on prices you will get by DIN Deutsches Institut für Normung e.V. in Berlin.

The numbers after the titles of "Bergbau-Betriebsblätter" in brackets are price groups (dated 2014-01-01); they correspond with the following prices:

Group EUR 1 7,70 2 10,50 3 13,10 4 15,70


FB Shaft 01Register of Mining Standards 2015-02

01 Shaft

NA 008-01-01 AA Shaft sinking

DIN 4930 06.89 Pipes for use in freezing shaft sinking; dimensions and technical delivery conditions (5)

DIN 21151 11.09 Shaft sinking; pulleys for flat winding ropes; safety requirements and testing (8)

DIN 21151 02.15 Shaft sinking - Pulleys for flat winding ropes - Safety requirements and testing (8)

E

DIN 21164 05.03 Shaft sinking - Riders for winding kibbles - Safety requirements and testing (12)

DIN 21164 10.14 Shaft sinking - Riders for winding kibbles - Safety requirements and testing (13)E

DIN 21181-1 03.10 Shaft sinking Debris kibbles - Part 1: Debris kibbles with suspension hanger (12)

DIN 21181-2 03.10 Shaft sinking; debris kibbles - Part 2: Debris kibbles with suspension two-strand chain set (9)

DIN 21186 03.13 Shaft sinking - Rope suspension gears for load hoisting in shafts (7)

DIN 21187 03.13 Shaft sinking - Chain suspension gears for load hoisting in shafts (6)

DIN 21194 12.99 Shaft sinking - Abutment for guide ropes - Safety requirements and testing (7)

DIN 21198 11.09 Shaft sinking - Shaft plumbs (6)

DIN 21500 11.01 Shaft sinking in mining - Design and dimensioning (12)

NA 008-01-02 AA Shaft transport

DIN 4118 06.81 Head frames and winding towers for mines; Design loads, calculation principles and design principles (4) /FABERG co-author/

DIN EN 12385-1 01.09 Steel wire ropes - Safety - Part 1: General requirements; German version EN 12385-1:2002+A1:2008 (12) /FABERG co-author/

DIN EN 12385-2 06.08 Steel wire ropes - Safety - Part 2: Definitions, designation and classification; German Version prEN 12385-2:2002/+A1:2008 (20) /FABERG co-author/

DIN EN 12385-2/B1 01.09 Steel wire ropes - Safety - Part 2: Definitions, designation and classification; German Version prEN 12385-2:2002/+A1:2008, Corrigendum to DIN EN 12385.2:2008-06 /FABERG co-author/

DIN EN 12385-3/B1 01.09 Steel wire ropes - Safety - Part 3: Information for use and maintenance; German version EN 12385-3:2004/+A1:2008, Corrigendem to DIN EN 12385.3:2008-06 /FABERG co-author/

DIN EN 12385-3 06.08 Steel wire ropes - Safety - Part 3: Information for use and maintenance; German version EN 12385-3:2004/+A1:2008 (13) /FABERG co-author/

DIN EN 12385-6 05.04 Steel wire ropes - Safety - Part 6: Stranded ropes for mine shafts; German version EN 12385- 6:2004 (12)

DIN EN 12385-7 02.03 Steel wire ropes - Safety - Part 7: Locked coil ropes for mine shafts; German version EN 12835-7:2002 (9)

DIN 20400 01.90 Knuckle threads for the mining; threads with large load-bearing depth (6)

DIN 21258 10.07 Lubricants and impregnating compounds for friction hoist ropes in mining - Safety requirements and testing (9)

DIN 21341 08.86 Wooden mine guides (6)

DIN 21346 11.89 Square head bolts for shaft guides (5)

DIN 21371 01.88 Rope attachments; assemblies (5)

DIN 21376-1 07.88 Guide shoes for shaft conveyances and counterweights with guide rollers in mining (5)

DIN 21376-2 07.88 Guide shoes for shaft conveyances and counterweights with slide-ways in mining (5)

DIN 21377 12.94 Steel railings for shaft conveyances in mining (5)


Mohammad

Highlight

Mohammad

Highlight

Mohammad

Highlight

Mohammad

Highlight

FB Shaft 01Register of Mining Standards 2015-02

DIN 21381 01.88 Rope attachments; thimble connection plates for round ropes (5)

DIN 21382 01.88 Rope attachments; outer plates, inner plates (5)

DIN 21383 01.88 Rope attachments; pins (5)

DIN 21386 01.88 Rope attachments; thimbles for round ropes (5)

DIN 21388 01.88 Rope attachments; universal joints (5)

DIN 21389 01.88 Rope attachments; clamp thimbles (5)

DIN 21390 02.85 Thimbles for flat ropes (5)

DIN 22400 04.90 Control units of winding engines; hoists and winches for mining (5)

DIN 22405 05.90 Friction pulley linings for winches and winders in mining (5)

DIN 22406 10.86 Low speed Koepe winding machines with friction wheel, for shafts and drifts; braking system calculation formulae (13)

DIN 22410 05.94 Winding rope pulleys for round ropes (10)


FB Mine Support 02Register of Mining Standards 2015-02

02 Mine Support

NA 008-02-01 AA Strut support

DIN EN 1804-1 05.10 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 1: Support units and general requirements; German version EN 1804-1:2001+A1:2010 (16)

DIN EN 1804-2 05.10 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 2: Power set legs and rams; German version EN 1804-2:2001+A1:2010 (16)

DIN EN 1804-3 05.10 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems; German version EN 1804-3:2006+A1:2010 (15)

DIN 21317 06.87 Round pit timber; timber for lagging (5)

DIN 21546 08.90 Mine support; strut support; marking (3)

DIN 21549 03.88 Mine supports; powered walking supports; terminology (5)

DIN 21550 05.88 Mine support; roof bars for single props; testing, requirements (5)

DIN 21551 01.86 Mine support; roof bars single props; lengths (5)

DIN 21555 08.91 Mine support; graphical symbols for the open loop control of powered support (6)

DIN 21556 02.87 Mine support; valves for individual props; identification code (5)

DIN 21557 02.87 Mine support; yield valves for powered support; identification code (5)

DIN 21561 09.86 Mine support; head for single props; connecting dimensions (5)

NA 008-02-03 AA Roadway support

DIN 21319 02.89 Round pit timber; bolts (5)

DIN 21326 04.89 Sawn pit timber; boards and planks (5)

DIN 21327 02.89 Sawn pit timber; boards, planks and square-sawn timber for working platforms (5)

DIN 21329 06.87 Cut pit timber; technical terms of delivery and quality (5)

BB 21510 06.95 Verzugsmatten - Technische Anforderungen (2)E

DIN 21521-1 07.90 Rock bolts for mining and tunnelling; terms (6)

DIN 21521-2 02.93 Rock bolts for mining and tunnel support; general specifications for steel-bolts; tests, testing methods (7)

DIN 21522 07.72 Roof bolt plates for mining and tunnel support (4)

DIN 21530-1 05.03 Mine support - Part 1: General (5)

DIN 21530-2 05.03 Mine support - Part 2: Dimensions, designation and statical values (21)

DIN 21530-3 05.03 Mine support - Part 3: Requirements (10)

DIN 21530-4 05.03 Mine support - Part 4: Testing (10)

DIN 21530-5 05.03 Mine support - Part 5: Marking of parts of mine support (6)

DIN 21531-1 07.90 Arch supports; arches B 5, 4 to B 20, 2 (5)

DIN 21531-2 07.90 Arch supports; arches B 21, 7 to B 63 (5)


FB Extraction 03Register of Mining Standards 2015-02

03 Extraction

NA 008-03-01 AA Extracting and stowing

DIN EN 1552 09.03 Underground mining machines - Mobile extracting machines at the face - Safety requirements for shearer loaders and plough systems; German version EN 1552:2003 (10) /FABERG co-author/

DIN 20012 04.89 Pneumatic stowing pipes (5)

DIN 20013 04.89 Sealings for pneumatic stowing pipes (5)

DIN 20097 07.68 Gears for coal ploughs and underground chain- conveyors; signs for gears (4) /FABERG co-author/

DIN 20350 03.75 Protective clothing - General requirements; German version prEN 340:2000 (4) /FABERG co-author/


FB Tools 04Register of Mining Standards 2015-02

04 Tools

NA 008-04-01 AA Rock drilling/Hand tools

DIN 1197-1 06.90 Eyes for picks, oval; dimensions, requirements, testing (5)

DIN 1197-2 06.90 Pick eyes, oval; plug gauges (5)

DIN 6436 06.90 Pickaxes (5)

DIN 6437-1 06.90 Pickaxe handles; dimensions, requirements, testing (5)

DIN 6437-2 06.90 Pickaxe handles; gauges (5)

DIN 20109 06.90 Pickaxes, chisel and point ends (5)

DIN 20110 06.90 Beater-pickaxes (5)

DIN 20112 06.90 In triangular hand hoes (5)

DIN 20115 06.90 Miners axes (5)

DIN 20119 07.90 Trough shovel (5)

DIN 20120 07.90 Sand shovel (5)

DIN 20121 07.90 Digging shovel (5)

DIN 20123 07.90 Rimmed shovel (5)

DIN 20124 07.90 Pan shovel (5)

DIN 20125 07.90 Loading shovel (5)

DIN 20127 09.13 Garden tools - Non-motorized hand-held tools for using in soil - Spades (5) /FABERG co-author/

DIN 20128 07.90 Shallow rimmed shovel (5)

DIN 20129 07.90 Plain shovel (5)

DIN 20135 07.90 Sledge hammer (5)

DIN 20136 07.90 Hand hammer (5)

DIN 20142 07.92 Hacksaws with steel frames and two handles (5)

DIN 20151 01.84 Gears for coal ploughs and underground chain- conveyors; signs for gears (4) /FABERG co-author/

DIN 20152 03.89 Shovel and spade handels; types, dimensions, requirements, testing, marking (5) /FABERG co-author/

DIN 20301 01.99 Rock drilling operations - Terminology, units, and symbols for use in formulae (9)

DIN 20302 02.74 Rock drilling operations - Terminology, units, and symbols for use in formulae (8) /FABERG co-author/

DIN 20311 11.02 Drill tubes with diameters exceeding 100 mm for large hole boring in mining (5)

DIN 20314 06.90 Screw threads for drill tubes will diameters exceeding 100 mm for large hole boring in mining (5)

DIN 20316 11.12 Rock drilling - Thread connections for thin-walled rotary drilling equipment - Dimensions, design (5)

DIN 20317 02.14 Rock drilling - Round thread connections for percussive drilling equipment - Dimensions, design (4)

DIN 20351 04.14 Rock drilling - Wedge-shaped shank connections for rotary drilling equipment - Dimensions, design (6)

E

DIN 20361 04.10 Rock drilling - Chuck bushings - Connecting dimensions, material, design (4)

DIN 20367 04.10 Rock drilling - Round screw connections for rotary drilling equipment - Dimensions, design (5)

DIN 20369 09.89 Pick hammers; flat- and shearpick without and with shank (5)

DIN 20371 09.69 Hammer drilling; connecting tap for hammer drilling support (4) /FABERG co-author/


FB Tools 04Register of Mining Standards 2015-02

DIN 20372 05.88 Rock drilling; water tube; connecting dimensions, material, finish (5)

DIN 20374 01.88 Pick hammers; gauges for picks (5)

DIN 20375 01.88 Pick hammers; round picks without shank (5)

DIN 20376 01.88 Pick hammers; round picks with shank (5)

DIN 20377 11.09 Rock drilling - Flush drills - Drill rod profiles, shanks and tapers (7)

DIN 20378 10.90 Drilling hammers; taper gauges for tapered connections of drill rods and bits (5)

DIN 20379-1 05.11 Rock drilling - Part 1: Tapered bits for percussive flush drilling (7)

DIN 20379-2 05.11 Rock drilling - Part 2: Bits with internal thread for percussive flush drlling (7)

DIN 24063 01.80 Operating elements (control devices) for pneumatic tools; terms, safety requirements (4) /FABERG co-author/

DIN 68340 01.89 Timber handles for impact tools; technical specifications (5) /FABERG co-author/


FB Transport 05Register of Mining Standards 2015-02

05 Transport

NA 008-05-01 AA Mine railways

DIN 5902 11.95 Fishplates for grooveless flat bottom rails dimensions - Steel types (10) /FABERG co-author/

DIN 5904 11.95 Steel sleepers - Dimensions, static values, steel types (6) /FABERG co-author/

DIN 5906 11.95 Short clips for grooveless flat bottom rails - Dimensions, steel types (6) /FABERG co-author/

DIN 5914 03.65 baseplate scrwes with rectangular head (4) /FABERG co-author/

DIN 20449 10.88 Points and crossovers for rail haulage roads in mines; standard types, terminology (7)

DIN 20450 10.88 Simple underground track points; 20 m radius, 1 : 5 inclination; geometric dimensions (5)

DIN 20452-1 10.88 Simple points for underground tracks with loose heel switch; 20 m radius, 1 : 5 inclination, 600 mm gauge; compilation (5)

DIN 20452-2 10.88 Simple points for underground tracks with spring switch blade; 20 m radius, 1 : 5 inclination, 600 mm gauge; compilation (5)

DIN 20453-1 10.88 Switches for simple underground track points with loose heel switch; 20 m radius, 1 : 5 inclination, 600 mm gauge (5)

DIN 20453-2 10.88 Switches for simple underground track points with spring switch blade; 20 m radius, 1 : 5 inclination, 600 mm gauge (5)

DIN 20454 10.88 Crossings for simple underground track points; 20 m radius, 1 : 5 inclination, 600 mm gauge (5)

DIN 20455 10.88 Check rail device for simple underground track points; 20 m radius, 1 : 5 inclination, 600 mm gauge (5)

DIN 20458 10.88 Simple crossovers for underground tracks; 20 m radius, 1 : 5 inclination; geometric dimensions (5)



















DIN 20499 01.07 Rail haulage roads in mines - General rules (12)

DIN 20500 10.88 Underground mine railways; track gauges and rails; standard types and selection (5)

DIN 20500 09.14 Underground mine railways - track gauges and rails; standard types and selection (5)

E

DIN 20501 07.88 Pit railways; rails S 30, butt strap Fl 30 (5)

DIN 20501 09.14 Underground mine railways - But strap Fl 30 for rail 30E1 (5)E

DIN 20506 07.90 Clamping plates for securing rails onto steel supports (5)

DIN 20506 09.14 Underground mine railways - Clamping plates for securing rails onto steel supports (5)

E

DIN 20548 07.90 Wheel sets for rail vehicles used in mines; rules for measuring (5)

DIN 20549 11.86 Track gauges for pit railways; definition and tolerances (5)

DIN 20550 07.90 Mine cars size small; components, main dimensions, design (5)

DIN 20551 01.12 Mine cars - front wall, casing, frame, buffer sheet (9)

DIN 20552 11.88 Small size lubs; bumpers, supporting beam (5)

DIN 20553 01.12 Wheel sets with taper roller bearings for mine cars; without springs (8)

DIN 20555 01.12 Wheel sets with taper roller bearings for mine cars; exterior spring suspension (11)

DIN 20556 01.12 Wheel sets with taper roller bearings for mine cars; interior spring suspension

DIN 20560 07.89 Mine cars; middle size; dimensions, design and construction (5)

DIN 20570 04.89 Mine cars; large size; dimensions, design and construction (5)

DIN 20575-1 10.03 Rail transport - Passenger cars for underground mining - Part 1: Requirements (6)

DIN 20579-1 07.86 Buffer springs for mine cars; calculation (5)

DIN 20579-2 07.86 Buffer springs for mine cars; requirements (5)

DIN 20581 03.88 Mine cars; strap type coupling (5)

DIN 20583 11.95 Mine cars - Shackle coupling (5)

DIN 20586 01.12 Rail fastenings in mining for S 30E1 and 33E1 rails on wooden sleepers (8)

DIN 20600 01.07 Mine railways - Wheel profils for locomotives and cars (5)

DIN 20600 09.14 Mine railways - Wheel profils for locomotives and cars (5)E

DIN 20601 05.91 Mine cars; tyres for mine locomotives (5)

DIN 21325 02.12 Pit converted timber - Timber sleepers (5)

DIN 45635-52 05.86 Measurement of airborne noise emitted by machines; enveloping surface method; mine diesel locomotives and mine road railers (5) /FABERG co-author/

DIN 45635-53 05.86 Measurement of airborne noise emitted by machines; enveloping surface method; diesel traction trolleys (5) /FABERG co-author/

DIN 45635-54 05.86 Measurement of airborne noise emitted by machines; enveloping surface method; mine trackless vehicles (5) /FABERG co-author/

DIN 45635-55 05.86 Measurement of airborne noise emitted by machines; enveloping surface method; shunting trolleys with friction- wheel and/or gearwheel drive (5) /FABERG co-author/



NA 008-05-02 AA Suspended monorails

DIN 20590 04.90 Securing devices on underframes used in mining (5)

DIN 20592-1 08.91 Suspended monorails for mining; transport boxes; dimensions and requirements (5)

DIN 20592-2 08.91 Suspended monorails for mining; attachment facilities for transport boxes; dimensions and requirements (5)

DIN 20593-1 11.02 Monorails for mining - Rails - Part 1: Straight rails for profile I 140 E (7)

DIN 20593-2 11.02 Monorails for mining - Rails - Part 2: Curved rails and adapting rails for profile I 140 E (8)

DIN 20593-3 07.04 Monorails for minging - Rails - Part 3: Straight rails and rail-connections for profiles I 140V and I 250 (11)

DIN 20593-4 04.07 Monorails for minging - Rails - Part 4: Curved rails and adapting rails for profiles I 140 V and I 250 (12)

DIN 20594 08.91 Suspension claws for mining, for loads up to 30 kN; requirements and testing (7)

DIN 20597 05.92 Suspended monorails for mining; toothed disc (5)

DIN 20597 08.13 Suspended monorails for mining - Toothed disc (4)E

DIN 20599 08.93 Suspended monorails for mining; rope positions, mounting devices, clearance dimensions for bogies (5)

DIN 20619 08.93 Suspended monorails for mining; winding-drum with suspension hook; dimensions and requirements (6)

DIN 20620-1 10.94 Force-guided tram-ways in mining - Part 1: Survey; structure and terms (5)

DIN 20620-2 10.94 Force-guided tram-ways in mining - Part 2: Monorails; structure and terms (6)

DIN 20620-3 10.94 Force-guided tram-ways in mining - Part 3: Free-steered machines; structure and terms (6)

DIN 20622 11.02 Suspended-monorail transport systems for mining - Permissible loads for suspensions and their abnutments and railprofile I 140 E (10)

DIN 20622 08.13 Suspended-monorail transport systems for mining - Permissible loads for suspensions and their abnutments and railprofile I 140 E (12)

E

DIN 20625-1 03.92 Capture-track rail installations in mining; bolted couplings for rope-hauled and self-propelled rail installations; bolted coupling 30 (7)

DIN 20629-1 08.01 Suspended monorails for mining - Mounting regulations - Part 1: for cable-driven suspended monorails (7)

DIN 20629-2 08.01 Suspended monorails for mining - Mounting regulations - Part 2: for loco-driven suspended monorails (8)

DIN 20629-2 08.13 Suspended monorails for mining - Mounting regulations - Part 2: For loco-driven suspended monorails (13)

E

DIN 20629-3 08.01 Suspended monorails for mining - Mounting regulations - Part 3: Calculations (5)

DIN 20633 04.02 Overhead monorail installations for mining - Double-end fork turnbuckles (7)

DIN 20635 05.01 Monorails for mining - Suspensions shackles (6)

DIN 20636 06.01 Monorails for mining - Suspension claws - Requirements and testing (5)

DIN 20637 10.97 Monorails for mining - Tested round steel chains for suspensions - Tested, long link (5)

NA 008-05-03 AA Belt conveyors

DIN EN ISO 252 01.08 Conveyor belts - Ply adhesion between constitutive eleents - Test methods (ISO 252:2007); German version EN ISO:2007 (8) /FABERG co-author/

DIN EN ISO 283 02.08 Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISO 283:2007); German version EN ISO 283:2007 (9) /FABERG co-author/



DIN EN ISO 283 10.14 Textile conveyor belts - Full thickness tensile strength, elongation at break and elongation at the reference load - Test method (ISOIDIS 283:2014); German version prEN ISO 283:2014 (9) /FABERG co-author/

E

DIN EN ISO 340 10.13 Conveyor belts - Laboratory scale flammability characteristics - Requirements and test method (ISO 340:2013) German version EN ISO 340:2013 (8) /FABERG co-author/

DIN EN ISO 505 04.00 Conveyor belts - Method for the determination of the tear propagation resistance of textile conveyor belts (ISO 505:1999); German version EN ISO 505:1999 (6) /FABERG co-author/

DIN EN ISO 583 03.08 Conveyor belts with a textile carcass - Total belt thickness and thickness of constitutive elements - Method of test (ISO 583:2007); German version EN ISO 583:2007 (9) /FABERG co-author/

DIN EN ISO 703 03.08 Conveyor belts - Transverse flexibility (troughability) - Test method (ISO 703:2007); German version EN ISO 703:2007 (8) /FABERG co-author/

DIN EN ISO 1120 04.13 Conveyor belts - Determination of strength of mechanical fastenings - Static test method (ISO 1120:2012); German version EN ISO 1120:2012 (8) /FABERG co-author/

DIN EN 1554 10.12 Conveyor belts - Drum friction testing; German version EN 1554:2012 (9) /FABERG co-author/

DIN EN ISO 2842 04.13 Conveyor belts - Electrical conductivity - Specification and test method (ISO 284:2012); German Version EN ISO 284:2012 (8) /FABERG co-author/

DIN EN ISO 7590 03.10 Steel cord conveyor belts - Methods for the determination of total thickness and cover thickness (ISO 7590:2001); German version EN ISO 7590:2001 (8) /FABERG co-author/

DIN EN ISO 7622-1 11.13 Steel cord conveyor belts - Longitudinal traction test - Part 1: Measurement of elongation (ISO 7622-1:2013); German version EN ISO 7622-1:2013 (6) /FABERG co-author/

DIN EN ISO 7622-2 11.95 Steel cord conveyor belts - Longitudinal traction test - Part 2: Measurement of tensile strength (ISO 7622-2:1984); German version EN ISO 7622-2:1995 (6) /FABERG co-author/

DIN EN ISO 7622-2 10.14 Steel cord conveyor belts - Longitudinal traction test - Part 2: Measurement of tensile strength (ISO/DIS 7622-2:2014); German version prEN ISO 7622-2:2014 (7) /FABERG co-author/

E

DIN EN ISO 7623 08.97 Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after thermal treatment (ISO 7623:1996); German version EN ISO 7623:1997 (6) /FABERG co-author/

DIN EN ISO 8094 11.13 Steel cord conveyor belts; Adhesion strength test of the cover to the core layer (ISO 8094:2013); German version EN ISO 8094:2013 (6) /FABERG co-author/

DIN EN ISO 9856 11.12 Conveyor belts - Determination of elastic and permanent elongation and calculation of elastic modulus (ISO 9856:2003 + Amd 1:2012); German version EN ISO 9856:2003 + A1:2012 (10) /FABERG co-author/

DIN EN 12881-1 11.14 Conveyor belts - Fire simulation flammability testing - Part 1: Propane burner tests; German version EN 12881-1:2014 (16) /FABERG co-author/

DIN EN 12881-2 10.09 Conveyor belts - Fire simulation flammability testing - Part 2: Large scale fire test; German version EN 12881-2:2005+A1:2008 (8) /FABERG co-author/

DIN EN 12882 03.10 Conveyor belts for general purpose use - Electrical and flammability safety requirements; German version EN 12882:2008 (11) /FABERG co-author/

DIN EN 12882 07.14 Conveyor belts for general purpose use - Electrical and flammability safety requirements; German version prEN 12882:2013 (10) /FABERG co-author/

E

DIN EN 13827 07.04 Steel cord conveyor belts - Determination of the lateral and vertical displacement of steel cords; German version EN 13827:2003 (7) /FABERG co-author/

DIN EN ISO 14890 06.13 Conveyor belts - Specification for rubber or plastics-covered conveyor belts of textile construction for general use (ISO 14890:2013); German version EN ISO 14890:2013 (12) /FABERG co-author/



DIN EN 14973 12.09 Conveyor belts for use in underground installations - Electrical and flammability safety requirements; German version EN 14973:2006+A1:2008 (11) /FABERG co-author/

DIN EN 14973 07.14 Conveyor belts for use in underground installations - Electrical and flammability safety requirements; German version prEN 14973:2013 (11) /FABERG co-author/

E

DIN 15207-1 10.00 Continuous mechanical handling equipment - Idlers for belt conveyors - Main dimensions of idlers for belt conveyors for bulk material (5) /FABERG co-author/

DIN EN ISO 15236-1 04.06 Steel cord conveyor belts - Part 1: Design, dimensions and mechanical requirements for conveyor belts for general use (ISO 15236-1:2005); German version EN ISO 15236-1:2005 (12) /FABERG co-author/

DIN EN ISO 15236-2 09.04 Steel cord conveyor belts - Part 2: Preferred belt types (ISO 15236-2:2004); German version EN ISO 15236-2:2004 (8) /FABERG co-author/

DIN EN ISO 15236-3 04.08 Steel cord conveyor belts - Part 3: Special safety requirements for belts for use in underground installations (ISO 15236-3:2007); German version EN ISO 15236-3:2007 (11) /FABERG co-author/

DIN EN ISO 15236-4 09.04 Steel cord conveyor belts - Part 4: Vulcanized belt joints (ISO 15236-4:2004); German version EN ISO 15236-4:2004 (8) /FABERG co-author/

DIN EN ISO 16851 09.13 Textile conveyor belts - Determination of the net length of an endless (spliced) conveyor belt (ISO 16851:2012); German version EN ISO 16851:2013 (6) /FABERG co-author/

DIN 22101 12.11 Continuous conveyors - Belt conveyors for loose bulk materials - Basis for calculation and dimensioning (21)

DIN 22101 12.11 Continuous conveyors - Belt conveyors for loose bulk materials - Basis for calculation and dimensioning (English translation) (21)

DIN 22102-1 01.14 Conveyor belts with textile plies for bulk goods - Part 1: Dimensions, specifications, marking (7) /FABERG co-author/

DIN 22102-2 01.14 Conveyor belts with textile plies for bulk goods - Part 2: Testing (6) /FABERG co-author/

DIN 22102-3 01.14 Conveyor belts with textile plies for bulk goods - Part 3: Permanent joints (9) /FABERG co-author/

DIN 22107 08.84 Continous mechanical handling equipment; idler sets for belt conveyors for loose bulk materials; principal dimensions (5) /FABERG co-author/

DIN 22109-1 07.00 Conveyor belts with textile plies for coalmining - Part 1: Monoply belts for underground applications; dimensions, requirements (6)

DIN 22109-1 08.13 Conveyor belts with textile plies for coalmining - Part 1: Monoply belts for underground applications - Dimensions, requirements (6)

E

DIN 22109-2 07.00 Conveyor belts with textile plies for coalmining - Part 2: Rubber-belts with two plies for underground applications; dimensions, requirements (6)

DIN 22109-2 08.13 Conveyor belts with textile plies for coalmining - Part 2: Rubber-belts with two plies for underground applications - Dimensions, requirements (6)

E

DIN 22109-4 07.00 Conveyor belts with textile plies for coalmining - Part 4: Rubber-belts with two plies for above ground applications; dimensions, requirements (6)

DIN 22109-4 08.13 Conveyor belts with textile plies for coalmining - Part 4: Rubber-belts with two plies for above ground applications; Dimensions, requirements (6)

E

DIN 22109-5 02.88 Conveyor belts with textile plies for coalmining; branding (5)

DIN 22109-6 12.03 Conveyor belts with textile plies for coalmining - Part 6: Testing (6)

DIN 22110-2 10.97 Testing methods for conveyor belt joints - Part 2: Endurance running tests, determination of running time of belt joints at conveyor belts with textile plies (5)

DIN 22110-3 11.07 Testing methods for conveyor belt joints - Part 3: Determination of time strength for conveyor belt joints (dynamical testing method) (8)

DIN 22110-3 08.13 Testing methods for conveyor belt joints - Part 3: Determination of time strength for conveyor belt joints (dynamical testing method) (8)

E



DIN 22111 11.07 Belt conveyors for underground coal mining - Light construction (11)

DIN 22112-1 12.10 Belt conveyors for underground coal mining - Idlers - Part 1: Dimensions (6)

DIN 22112-2 12.10 Belt conveyors for underground coal mining - Idlers - Part 2: Requirements (5)

DIN 22112-3 03.96 Belt conveyors for underground coalmining - Idlers - Part 3: Testing (7)

DIN 22114 12.10 Belt conveyors for underground coalmining - Heavy construction (12)

DIN 22115 10.03 Belt conveyors for underground coalmining; Coating on idlers; Requirements and testing (7)

DIN 22116 10.03 Belt conveyors for underground coal mining - Pressure rollers DN 159 - Dimensions, requirements, marking (6)

DIN 22117 02.88 Conveyor belts for coalmining; determination of the oxygen index (6)

DIN 22120 04.05 Elastomere scraper plates for belt conveyors in hard coal mines (6)

DIN 22121 07.00 Conveyor belts with textile plies for coalmining - Permanent joints for belts with one or two plies; dimensions, requirements, marking (6)

DIN 22121 08.13 Conveyor belts with textile plies for coalmining - Permanent joints for belts with one or two plies - Dimensions, requirements, marking (7)

E

DIN 22122 10.03 Continous mechanical handling equipment - Troughability of conveyor belts - Determination of that portion of width of conveyor belting in contact with idlers, requrements, testing (6)

DIN 22123 10.12 Conveyor belts - Indentation rolling resistances of conveyor belts related to beltwidth - Requirements, testing (8)

DIN 22129-1 02.88 Steel cord conveyor belts for underground coalmining; dimensions, requirements (6)

DIN 22129-2 02.88 Steelcord conveyor belts for underground coalmining; marking (5)

DIN 22129-3 02.88 Steelcord conveyor belts for underground coalmining; testing (6)

DIN 22129-4 11.91 Steelcord conveyor belts for use in underground coal mining; belt joints; dimensions, requirements (6)

DIN 22129-4 02.14 Steelcord conveyor belts for use in underground coal mining - Belt joints - Part 4: Dimensions, requirements (8)

E

DIN 22131-3 11.88 Steelcord conveyor belts for hoisting and conveying; testing (5)

DIN EN ISO 22721 01.10 Conveyor belts - Specification for rubber- or plastics-covered conveyor belts of textile construction for underground mining (ISO 22721:2007); German version EN ISO 22721:2007 (11) /FABERG co-author/

DIN 53530 02.81 Testing of organic materials; Separation test on fabric plies bonded together (5) /FABERG co-author/

NA 008-05-05 AA Components for chain conveyors

DIN 763 12.90 Tested, non-calibrated, long-link round steel chains (5) /FABERG co-author/

DIN 8175 02.80 Conveyor chains; bush conveyor chains, heavy type (4) /FABERG co-author/

DIN 8176 01.80 Conveyor chains; bush conveyor chains for haulage systems (4) /FABERG co-author/

DIN EN 12321 07.09 Underground mining machinery - Specification for the safety requirements for armoured face conveyors; German version EN 12321:2003+A1:2009 (12)

DIN 22200 05.94 Continous mechanical handling equipment; idler sets for belt conveyors for loose bulk materials; principal dimensions (5) /FABERG co-author/

BB 22249 12.72 Schmiernippel für den Bergbau (2)

DIN 22252 07.12 Round steel link chains for use in continuous conveyors and winning equipment in mining (11)

DIN 22253 03.08 Chain connectors - Shackle type connector units - Dimensions, requirements, testing (12)

DIN 22255 05.12 Flat link chains for use in continuous conveyors in mining (12)



DIN 22256 10.02 Chain sprockets for chain conveyors and coal winning equipment - Dimensions, requirements, testing (English translation)

DIN 22256 10.02 Chain sprockets for chain conveyors and coal winning equipment - Dimensions, requirements, testing (11)

DIN 22257 06.90 Scraper bars for chain conveyors; outboard chain assembly; dimensions, requirements, testing (5)

DIN 22258-1 05.12 Chain connectors - Part 1: Flat type connectors (10)

DIN 22258-2 08.03 Chain connectors - Part 2: Kenter type connectors (9)

DIN 22258-2 08.03 Chain connectors - Part 2: Kenter type connectors (English translation)

DIN 22258-2 03.14 Chain connectors - Part 2: Kenter type connectors (11)E

DIN 22258-3 05.12 Chain connectors - Part 3: Block type connectors (10)

DIN 22259 05.07 Flightbars for use in chain conveyors in mining (10)

NA 008-05-06 AA Pipe systems

DIN 20002-1 11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominal pressure 10 (5)

DIN 20002-2 11.89 Pipelines for mining; steel tubes with loose flanges and collars; projection and recess; nominal pressure 6 (5)

DIN 20002-3 11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominal pressure 40 (5)

DIN 20003-1 09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominal pressure 10 (7)

DIN 20003-2 09.87 Steel tubes for mining; fittings with loose flanges and plain collars, projection and recess; nominal pressure 6 (7)

DIN 20003-3 09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominal pressure 40 (6)

DIN 20004-1 12.00 Steel tubes for mining - Part 1: Interpose rings rated for PN 10 and PN 40 (6)

DIN 20004-2 12.00 Steel tubes for mining - Part 2: Wedge rings rated for PN 10 and PN 40 (5)

DIN 20006 09.89 Pipeline for mining; sealings for steel tubes according to DIN 20002 and fittings according to DIN 20003 (5)

DIN 20042 08.01 Watervalve, nominal pressure 40 - Dimensions and requirements (5)

BB 20065-1 02.78 Kunststoff-Rohrleitungen - Richtlinien für die Verlegung - Thermoplastische Kunststoffe (2)

BB 20065-2 02.78 Kunststoff-Rohrleitungen - Richtlinien für die Verlegung - Mitgeltende Normen (2)

DIN 24251 08.73 Multistage centrifugal pumps; mine drainage pumps, with pump total head up to 1000 m at speed of rotation 1500 l/min (4) /FABERG co-author/

NA 008-05-07 AA Hose assemblies

DIN EN 853 02.97 Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification; German version EN 853:1996 (7) /FABERG co-author/

DIN EN 853 05.13 Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification; German version prEN 853:2013 (11) /FABERG co-author/

E

DIN EN 854 02.97 Rubber hoses and hose assemblies - Textile reinforced hydraulic type - Specification; German version EN 854:1996 (7) /FABERG co-author/

DIN EN 854 05.13 Rubber hoses and hose assemblies - Textile reinforced hydraulic type - Specification; German version prEN 854:2013 (11) /FABERG co-author/

E

DIN EN 856 02.97 Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification; German version EN 856:1996 (7) /FABERG co-author/



DIN EN 856 05.13 Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification; German version prEN 856:2013 (11) /FABERG co-author/

E

DIN EN 857 02.97 Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification; German version EN 857:1996 (6) /FABERG co-author/

DIN EN 857 05.13 Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification; German version prEN 857:2013 (10) /FABERG co-author/

E

DIN EN ISO 1402 04.10 Rubber and plastic hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009); German version EN ISO 1402:2009 (10) /FABERG co-author/

DIN EN ISO 7751 12.11 Rubber and plastics hoses and hose assemblies - Ratios of proof and burst pressure to maximum working pressure - Amendment 1 (ISO 7751:1991 + Amd 1:2011); German version EN ISO 7751:1997 + A1:2011 (6) /FABERG co-author/

DIN EN ISO 8030 11.14 Rubber and plastics hoses - Method of test for flammability (ISO 8030:2014); German version EN ISO 8030:2014 (8) /FABERG co-author/

DIN EN ISO 8031 04.10 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and electrical conductivity (ISO 8031:2009); German version EN ISO 8031:2009 (12) /FABERG co-author/

DIN EN ISO 8033 11.06 Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2006); German version EN ISO 8033:2006 (10) /FABERG co-author/

DIN EN ISO 8330 02.10 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2007); German version prEN ISO 8330:2008 (14) /FABERG co-author/

DIN EN ISO 8330 07.11 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO/DIS 8330:2011); German version prEN ISO 8330:2011 (15) /FABERG co-author/

E

DIN 20018-1 04.03 Textile-reinforced hoses - Part 1: Maximal working pressure PN 10/16 (7)

DIN 20018-2 04.03 Textile-reinforced hoses - Part 2: Maximal working pressure PN 40 (5)

DIN 20018-3 04.03 Textile-reinforced hoses - Part 3: Maximal working pressure PN 100 (5)

DIN 20018-4 04.03 Textile-reinforced hoses - Part 4: Testing (6)

DIN 20021 02.97 Fluid-systems - Hoses with layer - Completation for DIN EN 853 to DIN EN 857 (5)

DIN 20029 10.90 Hose fittings; 1:3 taper gauges (5)

DIN 20030 06.92 Hose fittings; straight-way-cock with grip; dimensions, materials, requirements (5)

DIN 20033 07.90 Hose fittings; tapered nozzle with clamping nut (6)

DIN 20035 10.90 Hose fittings; flange nozzle; nominal pressure 16 (5)

DIN 20036 10.90 Hose fittings; coupling nipples with round thread form (5)

DIN 20037 10.90 Hose fittings; connecting nipple; dimensions (5)

DIN 20038 10.90 Hose fittings; coupling nozzles (5)

DIN 20039 08.98 Hose fittings - Hose clamps (5)

DIN 20040 10.90 Hose fittings; nipple valves; nominal pressure 16 (5)

DIN 20043 09.03 Staple-lock couplings for hydraulic power-transmission circuits (7)

DIN 20044 05.03 Staple-lock couplings type S for hydraulic power-transmission circuits - Dimensions, requirements, testing (7)

DIN 20066 01.12 Hydraulic fluid power - Hose assemblies - Dimensions, requirements (13) /FABERG co-author/

NA 008-05-08 AA Mobile machines

DIN EN 1889-1 10.11 Machines for underground mines - Mobile machines working underground - Safety - Part 1: Rubber tyred vehicles; German version EN 1889-1:2011 (18)



DIN EN 1889-2 07.09 Machines for underground mines - Mobile machines working underground - Safety - Part 2: Rail locomotives; German version EN 1889-2:2003+A1:2009 (20)

DIN EN 12111 10.14 Tunnelling machines - Road headers and continuous miners - Safety requirements; German version EN 12111:2014 (19) /FABERG co-author/

DIN EN 16191 09.14 Tunnelling machinery - Safety requirements; German version EN 16191:2014 (20) /FABERG co-author/


FB Ventilation 06Register of Mining Standards 2015-02

06 Ventilation

NA 008-06-01 AA Air doors

DIN EN 12110 02.10 Tunnelling machines - Air locks - Safety requirements; German version EN 12110:2002+A1:2008 (12) /FABERG co-author/

DIN EN 12110 10.14 Tunnelling machines - Air locks - Safety requirements; German version EN 12110:2014 (13) /FABERG co-author/

DIN 21631 03.11 Air regulating systems for mining - Wing air doors for travelling tracks - One-wing type air doors without pressure reduction (11)

DIN 21632 03.11 Air regulating systems for mining - Wing air doors for haulage tracks - One-wing type air doors without pressure reduction (11)

DIN 21633 03.11 Air regulating systems for mining - Wing air doors for haulage tracks - Double-wing type doors without pressure reduction (12)

DIN 21634 03.11 Air regulation systems for mining - Swinging roadway air doors for haulage tracks (11)

DIN 21635 02.98 Air regulation systems in mining - Air locks - Building and operation (7)

DIN 21636 04.03 Air regulation systems in mining - Belt-conveyors-way air locks - Dimensions, identifications, requirements and testing (12)

DIN 21637 10.95 Air regulation systems in mining - Wing air doors for haulage tracks - Double-wing type doors with pressure reduction (8)

DIN 21638 05.99 Air regulation systems in mining - Wing air locks for travelling tracks - Double-wing type doors with pressure reduction (6)

DIN 21639/B1 11.04 Corrigenda to DIN 21639:1999-09 (0)

DIN 21639 09.99 Air regulation systems in mining - Travel-way air locks - Type doors with pressure (5)

DIN 21640-1 10.93 Air regulating systems in mining; pneumatic cylinders for airdoors without pressure reduction; dimensions, requirement, marking (5)

NA 008-06-02 AA Installations for auxiliary ventilation

DIN 21603 10.09 Auxiliary ventilation for mining - Sheet airducting with collars and loose flanges (5)

DIN 21605 07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for exhaust and forced ventilation - Spiral ventilation ducts (6)

DIN 21606 07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for forced ventilation - Flat ventilation ducts (6)

DIN 21610 07.10 Auxiliary ventilation in mining - Flexible plastic air ducts - Requirements and test methods (6)

DIN 21612 07.10 Auxiliary ventilation for mining - Cladding material for flexible airducts - Requirements, testing (5)

DIN 21613 10.09 Auxiliary ventilation for mining - Steel sheet connectors with flange and shoulder (5)

DIN 21614 10.09 Auxiliary ventilation for mining - Flanged sheet steel reducers (5)

DIN 21615 10.09 Auxiliary ventilation for mining - Sheet steel reducers with flange and shoulder (5)

DIN 21625 07.10 Fans with electric motor drive intended for use in potentially explosive atmospheres in coal mines (6)

DIN 21626 02.11 Fans with hybrid (electric/pneumatic) motor drive intended for use in potentially explosive atmospheres in coal mines (6)


FB Mine Safety 07Register of Mining Standards 2015-02

07 Mine Safety

NA 008-07-01 AA Personal safety and protective equipment

DIN EN 795 10.12 Personal fall protection equipment - Anchor devices; German version EN 795:2012 (18) /FABERG co-author/

DIN EN 1497 10.07 Personal fall protection equipment - Rescue harnesses; German version EN 1497:2007 (10) /FABERG co-author/

DIN EN 1498 01.07 Personal fall protection equipment - Rescue loops; German version EN 1498:2006 (11) /FABERG co-author/

DIN 5290-1 04.83 Snap hook from light metal; with setting nut; dimensions, requirements and testing (5) /FABERG co-author/

DIN 7472-2 01.91 Safety harness; steel fittings; connecting dimensions, safety requirements and testing (6) /FABERG co-author/

DIN EN ISO 14122-1 01.02 Safety of machinery - Permanent means of access to machinery - Part 1: Choise of fixed means of access between tow levels (ISO 14122-1:2001); German version EN ISO 14122-1:2001 (8) /FABERG co-author/

DIN EN ISO 14122-1 01.14 Safety of machinery - Permanent means of access to machinery - Part 1: Choise of fixed means of access between two levels (ISO/DIS 14122-1:2013); German version prEN ISO 14122-1:2013 (11) /FABERG co-author/

E

DIN EN ISO 14122-2 01.02 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and wlkways (ISO 14122-2:2001); German version EN ISO 14122-2:2001 (7) /FABERG co-author/

DIN EN ISO 14122-2 01.14 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO/DIS 14122-2:2013); German version prEN ISO 14122-2:2013 (11) /FABERG co-author/

E

DIN EN ISO 14122-3 01.02 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001); German version EN ISO 14122-3:2001 (9) /FABERG co-author/

DIN EN ISO 14122-3 01.14 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO/DIS 14122-3:2013); German version prEN ISO 14122-3:2013 (13) /FABERG co-author/

E

DIN EN ISO 14122-4 02.14 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO/DIS 14122-4:2014); German version prEN ISO 14122-4:2014 (20) /FABERG co-author/

E

DIN EN 14404 02.05 Personal protective equipment - Knee protectors for work in the neeling position; German version EN 14404:2004 (12) /FABERG co-author/

DIN 20180 06.10 Pulley for clothes hoists in pithead baths (5)

DIN 20182 06.10 Double loop chain for hoisting clothes in pithead baths - Not tested, non-calibrated (4)

DIN EN ISO 20344 02.13 Personal protective equipment - Test methods for footwear (ISO 20344:2011); German version EN ISO 20344:2011 (28) /FABERG co-author/

DIN EN ISO 20345 04.12 Personal protective equipment - Safety footwear (ISO 20345:2011); German version EN ISO 20345:2011 (16) /FABERG co-author/

DIN EN ISO 20346 09.14 Personal protective equipment - Protective footwear (ISO 20346:2014); German version EN ISO 20346:2014 (17) /FABERG co-author/

DIN EN ISO 20347 05.12 Personal protective equipment - Occupational footwear (ISO 20347:2012); German version EN ISO 20347:2012 (15) /FABERG co-author/

DIN 21800 06.89 Symbol mallet and iron (5)

DIN 21802 06.89 Symbols for mine rescue and gas protection squads (6)

DIN 23301 03.07 Safety footwear for underground mining (9)

DIN 23307 06.09 Leather backside protectors for miners (back skin) (5)

DIN 23311-1 06.85 Knee pads for mining; rubber knee pads (5)



DIN 23311-1 02.14 Knee pads for mining - Part 1: Rubber knee pads (6)E

DIN 23311-2 02.98 Knee pads for mining - Part 2: Plastic knee pads (6)

DIN 23311-2 01.15 Knee pads for mining - Part 2: Plastic knee pads (8)E

DIN 23320-1 10.14 Flameproof protective clothing for the mining industry - Protective clothing for people of mine rescue and gas rescue crews - Part 1: Safety requirements and testing (10)

DIN 23320-2 10.14 Flameproof protective clothing for the mining industry - Protective clothing for people of mine rescue and gas rescue and gas rescue crews - Part 2: Single-piece working suits (6)

DIN 23320-3 10.14 Flameproof protective clothing for the mining industry - Protective clothing for people of mine rescue and gas rescue crews - Part 3: Two-piece working suits (6)

DIN 23320-4 10.14 Flameproof protective clothing for the mining industry - Protective clothing for people of mine rescue and gas rescue crews - Part 4: Underwear (6)

DIN 23320-5 10.14 Flameproof protective clothing for the mining industry - Protecting clothing for people of mine rescue and gas rescue crews - Part 5: Protective hoods (8)

DIN 23323 05.07 Bathing sandals for miners (5)

DIN 23327 07.03 Shin protectors for mining (7)

DIN 23328 09.03 Clothing for the mining industry - Woven farbics for work suits (6)

DIN 23330 11.01 Safety markings for mines (15)

DIN 23330 11.13 Safety markings for mines (8)E

DIN 23341 05.05 Clothing for the mining industry - Two-piece work suits (Jacket and trousers) (7)

DIN 23342 08.05 Clothing for the mining industry - Singlet with 1/4 sleeves (7)

DIN 23343 03.07 Clothing for the mining industry - Shirt for miners (7)

DIN 23344 09.03 Clothing for the mining industry - Men's slip (6)

DIN 23345 08.05 Clothing for the mining industry - Long underpants (7)

DIN 23346 09.03 Clothing for the mining industry - Socks for mining workers (6)

DIN 23400 11.08 Rescue stretcher for mining (dragging basket) - Safety requirements and testing (10)

DIN 23405 09.12 First aid boxes and first aid material for use in mining (5)

DIN 24320 12.06 Fire resistant fluids - Hydraulic fluids of categories HFAE and HFAS - Characteristics and requirements (7) /FABERG co-author/

DIN 24531-1 04.06 Gratings used as stairtreads - Part 1: Metal gratings (7) /FABERG co-author/

DIN 24531-2 08.07 Gratings used as stairtreads - Part 2: Sheet metal gratings (7) /FABERG co-author/

DIN 24531-3 08.07 Gratings used as stairtreads - Part 3: Plastic gratings (6) /FABERG co-author/

DIN 24534 03.70 Chain locks (4) /FABERG co-author/

DIN 24537-1 04.06 Gratings used as floor coverings - Part 1: Metal gratings (7) /FABERG co-author/

DIN 24537-2 08.07 Gratings used as floor coverings - Part 2: Sheet metal gratings (7) /FABERG co-author/

DIN 24537-3 08.07 Gratings used as floor coverings - Part 3: Plastic gratings (7) /FABERG co-author/

DIN 34300 04.01 Rescue equipment - Rescue hooks with safety eyelet holes (6) /FABERG co-author/

DIN 51502 08.90 Designation of lubricants and marking of lubricant containers, equipment and lubricating points (7) /FABERG co-author/

DIN 51634 12.81 Mineral spirits; safety lamps mineral spirit; minimum requirements (5) /FABERG co-author/



NA 008-07-02 AA Lighting

DIN 20609 11.93 Lighting of mine locomotives; head lamps; design features, photometric requirements, meters and measurements (6)

DIN 20610 04.94 Lighting of mine locomotives; position lamps; design features, photometric requirements (5)

DIN 22433 10.03 Underground lighting in hardcoal mining - Terms (6)

DIN 22434-1 07.01 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 1: General specification (6)

DIN 22434-2 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 2: Coalfaces with shield support (5)

DIN 22434-3 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 3: T-junctions (5)

DIN 22434-4 11.96 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 4: Conveyor belt (5)

DIN 22434-5 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 5: Material handling places (5)

DIN 22434-6 02.03 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 6: Area of roadway-driving operation (5)

DIN 22434-7 07.95 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 7: Pit-bottom (5)

DIN 22434-8 01.04 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 8: Building sites (5)

DIN 22434-9 10.98 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 9: Areas of rail track operation (5)

DIN 22434-10 02.05 Underground lighting in hardcoal mining - Lighting-technological planning bases - Part 10: Workshops and special premises (6)

DIN 49741 11.68 Lamp cap BX22d/32 (4) /FABERG co-author/

DIN EN 60079-35-1 01.12 Explosive atmospheres - Part 35-1: Caplights for use in mines susceptible to firedamp - General requirements - Construction and testing in relation to the risk of explosion (IEC 60079-35-1:2011); German version EN 60079-35-1:2011 + Cor.:2011 (19) /FABERG co-author/

DIN EN 62013-2 02.07 Caplights for use in mines susceptible to firedamp - Part 2: Performance and other safety-related matters (IEC 62013-2:2005); German version EN 62013-2:2006 (12) /FABERG co-author/

NA 008-07-03 AA Explosion prevention and protection

DIN EN 1127-2 09.14 Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining; German version EN 1127-2:2014 (16)

DIN EN 1710 08.08 Equipment and components intended for use in potentially explosive atmospheres in underground mines; German version EN 1710:2005+A1:2008 (17)

DIN EN 13463-1 07.09 Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements; German versionrEN 13463-1:2009 (26) /FABERG co-author/

DIN EN 13463-5 10.11 Non-electrical equipment intended for use in potentially explosive atmospheres - Part 5: Protection by constructional safety "c"; German version EN 13463-5:2011 (17) /FABERG co-author/

DIN EN 14591-1/B1 06.06 Explosion prevention and protection in underground mines - Protective systems - Part 1: 2-bar explosion proof ventilation structures, Corrigenda to DIN EN 14591-1:2004-12; German version EN 14591-1:2004/AC.2006 (99)

DIN EN 14591-1 12.04 Explosion prevention and protection in underground mines - Protective systems - Part 1: 2-bar explosion proof ventilation structures; German version EN 14591-1:2004 (10)


Mohammad

Highlight

Mohammad

Highlight

Mohammad

Highlight


DIN EN 14591-2 07.07 Explosion prevention and protection in underground mines - Protective systems - Part 2: Passive water trough barriers; German Version EN 14591-2:2007 (17)

DIN EN 14591-4 09.07 Explosions prevention and protection in underground mines - Protective systems - Part 4: Automatic extinguishing systems for road headers; German version prEN 14591-4:2005 (9)

DIN EN 14983 06.07 Explosion prevention and protection in underground mining - Equipment and protective systems for firedamp drainage; German version EN 14983:2007 (13)

DIN 21577 09.96 Explosibility of coal dust in underground hard coal mining - Tests and assessments of coal dust-air-mixtures and hybrid mixtures (8)

DIN EN 50303 05.01 Group 1, category M1 equipment intended to remain functional in atmospheres endangered by firedamp and/or coal dust; German version EN 50303:2000 (7) /FABERG co-author/

DIN EN ISO 80079-36

09.14 Explosive atmospheres - Part 36: Non-electrical equipment for use in explosive atmospheres - Basic methods and requirements (ISO/DIS 80079-36:2014); German version prEN ISO 80079-36:2014 (29) /FABERG co-author/

E

DIN EN ISO 80079-37

09.14 Explosive atmospheres - Part 37: Non-electrical equipment for use in explosive atmospheres - Non electrical type of protection constructional safety "c", control of ignition source "b", liquid immersion "k" ISO/DIS 80079-37:2014); German version prEN ISO 80079-37:2014 (21) /FABERG co-author/

E

DIN EN ISO/IEC 80079-38

08.12 Explosive atmospheres - Part 38: Equipment and components in explosive atmospheres in underground mines (ISO/IEC 80079-38/CDV:2012); German version prEN ISO/IEC 80079-38:2012 (23)

E

NA 008-07-03-01 AK Apparatus for potentially explosive atmospheres for mining

DIN EN 1834-2 03.00 Reciprocating internal combustion engines - Safety requirements for design and construction of engines for use in potentially explosive atmospheres - Part 2: Group I engines for use in underground workings susceptible to firedamp and/or combustible dust; German version EN 1834-2:2000 (10) /FABERG co-author/

DIN 20401 12.04 Buttress threads - 0,8 mm to 2 mm pitch - Dimensions (6)

DIN 22416 09.86 Electrical apparatus for potentially explosive atmospheres in mining; triangular head bolts; safety requirements and testing (5)

DIN 22417 11.88 Electrical apparatus for potentially explosive atmospheres; forms of keys for triangular socket wrenches (5)

DIN 22418 04.89 Electrical apparatus for potentially explosive atmospheres for mining; screw plugs; safety requirements and testing (6)

DIN 22419-1 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable entries - Part 1: Requirements for basic design (8)

DIN 22419-2 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable entries - Part 2: Gland adaptors for entries; safety requirements and testing (6)

DIN 22419-3 12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable entries - Part 3: Gland flanges for entries; safety requirements and testing (7)

DIN 22424 03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangle head bolts (6)

DIN 22425 03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangular nuts (6)

NA 008-07-04 AA Blasting engineering

DIN EN 13630-1 03.04 Explosives for civil uses - Detonating cords and safety fuses - Part 1: Requirements; German version EN 13630-1:2003 (7)

DIN EN 13630-2 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 2: Determination of thermal stability of detonating cords and safety fuses; German version EN 13630-2:2002 (7)


Mohammad

Highlight

Mohammad

Highlight

Mohammad

Highlight


DIN EN 13630-3 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 3: Determination of sensitiveness to friction of the core of detonating cords; German version EN 13630-3:2002 (6)

DIN EN 13630-4 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 4: Determination of sensitiveness to impact of detonating cords; German version EN 13630-4:2002 (8)

DIN EN 13630-5 03.04 Explosives for civil uses - Detonating cords and safety fuses - Part 5: Determination of resistance to abrasion of detopnating cords; German version EN 13630-5:2003 (9)

DIN EN 13630-6 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 6: Determination of resistance to tension of detonating cords; German version EN 13630-6:2002 (6)

DIN EN 13630-7 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 7: Determination of reability of initiation of detonating cords; German version EN 13630-7:2002 (6)

DIN EN 13630-8 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 8: Determination of resistance to water of detonating cords and safety fuses; German version EN 13630-8:2002 (7)

DIN EN 13630-9 07.04 Explosives for civil uses - Detonating cords and safety fuses - Part 9: Determination of transmission of detonation from detonating cord to detonating cord; German version EN 13630-9:2004 (7)

DIN EN 13630-10 08.05 Explosives for civil uses - Detonating cords and safety fuses - Part 10: Determination of initiating capacity of detonating cords; German version EN 1360-10:2005 (8)

DIN EN 13630-11 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 11: Determination of velocity of detonation of detonating cords; German version EN 13630-11:2002 (6)

DIN EN 13630-12 12.02 Explosives for civil uses - Detonating cords and safety fuses - Part 12: Determination of burning duration of safety fuses, German version EN 13630-12:2002 (6)

DIN EN 13631-1 07.05 Explosives for civil uses - High explosives - Part 1: Requirements; German version EN 13631-1:2005 (7)

DIN EN 13631-2 12.02 Explosives for civil uses - High explosives - Part 2: Determionation of thermal stability of explosives; German version EN 13631-2:2002 (7)

DIN EN 13631-3 11.04 Explosives for civil uses - High explosives - Part 3: Determionation of sensitiveness to friction of explosives; German version EN 13631-3:2004 (8)

DIN EN 13631-4 12.02 Explosives for civil uses - High explosives - Part 4: Determionation of sentiveness to impact of explosives; German version EN 13631-4:2002 (8)

DIN EN 13631-5 12.02 Explosives for civil uses - High explosives - Part 5: Determionation of resistance to water; German version EN 13631-5:2002 (7)

DIN EN 13631-6 12.02 Explosives for civil uses - High explosives - Part 6: Determionation of resistance to hydrostatic pressure; German version EN 13631-6:2002 (7)

DIN EN 13631-7 02.04 Explosives for civil uses - High explosives - Part 7: Determionation of safety and reliability at extreme temperatures; German version EN 13631-7:2003 (7)

DIN EN 13631-10 02.04 Explosives for civil uses - High explosives - Part 10: Method for the verification of the means of initiation; German version EN 13631-10:2003 (8)

DIN EN 13631-11 02.04 Explosives for civil uses - High explosives - Part 11: Determionation of transmission of detonation; German version EN 13631-11:2003 (8)

DIN EN 13631-12 02.05 Explosives for civil uses - High explosives - Part 12: Specification of boosters with different initiating capability; German version EN 13631-12:2004 (6)

DIN EN 13631-13 07.03 Explosives for civil uses - High explosives - Part 13: Determionation of density; German version EN 13631-13:2003 (7)

DIN EN 13631-14 07.03 Explosives for civil uses - High explosives - Part 14: Determionation of velocity of detonation; German version EN 13631-14:2003 (8)



DIN EN 13631-15 07.05 Explosives for civil uses - High explosives - Part 15: Calculation of thermodynamic properties; German version prEN 13631-15:2003 (12)

DIN EN 13631-16 11.04 Explosives for civil uses - High explosives - Part 16: Detection and measurement of toxic gases; German version EN 13631-16:2004 (7)

DIN 20163 11.94 Blasting - Terminology, units and symbols (14)

DIN 20164-1 01.07 Blasting supplies - Explosives - Part 1: Requirements, testing, marking (12)

DIN 20165 08.10 Blasting supplies - Intrinsically safe detonators (permitted detonators) - Requirements and testing (8)

DIN 20166 11.12 Blasting supplies - Intrinsically safe detonating cords (permitted detonating cords) - Safety requirements and testing (10)

NA 008-07-05 AA Plastics

DIN 22100-1 07.09 Articles and materials from synthetics for use in underground mines - Part 1: Conveyor belts - Hygienic requirements, testing, marking (8)

DIN 22100-3 10.10 Articles and materials from synthetic for use in underground mines - Part 3: Spiral air ducts - Safety requirements, testing, marking (8)

DIN 22100-4 10.10 Articles and materials from synthetic for use in underground mines - Part 4: Flat air ducts - Safety requirements, testing, marking (6)

DIN 22100-5 10.10 Articles and materials from synthetic for use in underground mines - Part 5: Tubes, tube isolations and hoses - Safety requirements, testing, marking (8)

DIN 22100-6 10.10 Articles and materials from synthetic for use in underground mines - Part 6: Sheeting, coated/uncoated tissue, brattice materials and lagging mats - Safety requirements, testing, marking (7)

DIN 22100-7 08.11 Articles and materials from synthetics for use in underground mines - Part 7: Safety requirements, testing, marking (24)

DIN 22118 08.91 Conveyor belts with textile plies for use in coal mining; fire testing (6)


FB Analysis of Raw Material/Coal preparation 08Register of Mining Standards 2015-02

08 Analysis of Raw Material/Coal preparation

NA 008-08-01 AA Investigations of raw material/Preparation of hard coal

DIN 22005-1 09.14 Investigations of raw material in hard-coal-mining - Part 1: Survey (10)

DIN 22005-2 09.97 Investigations of the raw material in hard-coal-mining - Part 2: Terms relating to raw material (13)

DIN 22005-2 06.14 Investigations of the raw material in hard-coal-mining - Part 2: Terms relating to raw material (13)

E

DIN 22013 08.85 Investigations of the raw material in hard-coal-mining - Channel sample - Sampling and schema of tests (9)

DIN 22014 08.85 Investigations of the raw material in hard-coal mining - Raw coal sample from the production of a working area - Sampling and schema of tests (10)

DIN 22017 03.08 Investigations of the raw material in hard-coal-mining - Froth-flotation-analysis (12)

DIN 22018 01.85 Investigations of the raw material in hard-coal-mining determation of the particle-density-distribution by float-and-sink-analysis (10)

DIN 22019-1 03.85 Investigations of the raw material in hard-coal-mining; determination of the particle-size-distribution <größer>20 µm by sieve-analysis (12)

DIN 22020-1 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 1: Terms, survey of processes and their applications (7)

DIN 22020-2 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 2: Preparation of polished surface from lump material and particulate blocks (5)

DIN 22020-3 08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 3: Maceral analysis on particulated blocks (5)

DIN 22020-4 12.98 Investigations of raw material in hard-coal-mining - Microscopical examination of hard coal, coke and briquettes - Part 4: Microlithotype analysis on particulate blocks (6)

DIN 22020-5 02.05 Investigations of the raw material in hard-coal-mining - Microscopical examinations of hard coal, coke and briquettes - Part 5: Reflectance measurements on vitrinites (12)

BB 22020-7 09.74 Mikroskopische Untersuchungen an Steinkohlen, Koksen und Briketts - Sonderuntersuchungen (4)

DIN 22021 07.85 Investigations of the raw material in hard-coalmining - Microscopical examinations of rocks (17)

DIN 22024 02.89 Investigations of the raw material in hard-coal-mining - Determination of tensile strength on solid rock (5)

DIN 23004-1 11.11 Preparation of hard coal - Part 1: Survey (7)

DIN 23004-2 11.11 Preparation of hard coal - Part 2: Terms relating to processes (14)

DIN 23005 12.88 Preparation of hard coal - Description and estimation of raw coal properties in view of preparation (10)

DIN 23006-1 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 1: General rules, balance of quantities (15)

DIN 23006-2 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 2: Sizing (14)

DIN 23006-3 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 3: Cleaning (13)

DIN 23006-4 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 4: Separation of solids from water (12)


FB Analysis of Raw Material/Coal preparation 08Register of Mining Standards 2015-02

DIN 23006-5 12.12 Preparation of hard coal - Assessment of preparation equipment and processes - Part 5: Size reduction and dissociation, involuntary breakage (10)

DIN 23006-6 01.05 Preparation of hard coal - Assessment of preparation equipment and processes - Part 6: Homogenizing (11)

DIN 23007 10.05 Preparation of hard coal - Flocculants for process water - Terms, requirements, verification (12)

DIN 23008 05.88 Preparation of hard coal - Flotation agents - Terms, requirements, verification (8)

DIN 23009 03.90 Preparation of hard coal - Medium solids - Terms, requirements, testing (9)

DIN 23011-3 12.13 Preparation of hard coal - Preparation-plants - Part 3: Flow sheets and grafical symbols (15)

DIN 23011-4 11.06 Preparation of hard coal; preparation plants Part 4: Technical agreements with regard to the fixation of guaranties (7)

DIN 23011-5 11.06 Preparation of hard coal - Preparation plants - Part 5: Process control (9)

DIN 23011-6 12.04 Preparation of hard coal - Preparation plants - Part 6: Equipment and operation of a plant laboratory (9)

DIN 23011-7 11.06 Preparation of hard coal - Preparation plants - Part 7: Equipment monitoring (7)

DIN 23011-7 Bbl 1 12.09 Preparation of hard coal - Preparation plants - Part 7: Equipment monitoring; Supplement 1: Means of application for the standard (7)

DIN 23011-8 02.08 Preparation of hard coal - Preparation plants - Part 8: Process technical requirements on preparation equipment (13)


FB Cokery, Briquettes 09Register of Mining Standards 2015-02

09 Cokery, Briquettes

NA 008-09-01 AA Bricks for coke ovens

DIN 1089-1 02.95 Refractories for use in coke ovens - Part 1: Silica bricks - Requirements and testing (6)

DIN 1089-2 02.95 Refractories for use in coke ovens - Part 2: Fireclay bricks - Requirements and testing (7)

DIN 1089-3 10.90 Refractories for use in coke ovens; mortar for silica and fireclay bricks; requirements and testing (7)


FB Open Cast Mining 10Register of Mining Standards 2015-02

10 Open Cast Mining

NA 008-10-01 AA Excavators, spreaders and auxiliary equipment in opencast lignite mines

DIN 5651 11.79 Brake block holders and brake block keys for composite brake blocks on rail vehicles; technical specifications (4) /FABERG co-author/

DIN 22261-1 01.11 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 1: Construction, commissioning and monitoring (10)

DIN 22261-1 09.14 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 1: Construction, commissioning and monitoring (11)

E

DIN 22261-2 12.06 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 2: Calculation principles (32)

DIN 22261-2 09.14 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 2: Calculation principles (32)

E

DIN 22261-3 11.06 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 3: Welded connections, joint types, classification, test instruction (14)

DIN 22261-3 09.14 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 3: Execution of steel structures (21)

E

DIN 22261-4 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 4: Hoisting winch brakes (6)

DIN 22261-4 09.14 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 4: Hoisting winch brakes (5)

E

DIN 22261-5 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 5: Slewing brakes and overload protecting devices (7)

DIN 22261-5 09.14 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 5: Slewing brakes and overload protecting devices (6)

E

DIN 22261-6 12.07 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 6: Examination of ropes and rope end fittings (7)

DIN 22261-6 09.14 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part 6: Examination of ropes and rope end fittings (6)

E

DIN 43120 09.52 Electric railway vehicles; bow slipper holder for contact wire clamps (4) /FABERG co-author/

DIN 43139 12.67 Drums for contact-wires for electric traction (4) /FABERG co-author/

DIN 43153 01.68 Thimble with clevis for overhead equipment (4) /FABERG co-author/

DIN 43160 01.68 Eye and clevis for overhead equipment; connecting dimensions (4) /FABERG co-author/

NA 008-10-02 AA Belt conveyors in opencast lignite mining

DIN EN 14658 06.10 Continuous handling equipment and systems - General safety requirements for continuous handling equipment for opencast lignite mining; German version EN 14658:2005+A1:2010 (15)

NA 008-10-03 AA Surface Miner

DIN 22270 05.12 Continuous Surface Miner (CSM) - Safety (11)


FB Mine Plans 11Register of Mining Standards 2015-02

11 Mine Plans

NA 008-11-01 AA Mine surveying

DIN 18723-7 07.90 Field procedure for precision testing of surveying instruments - Part 7: Gyroscopes (6)

DIN 21961 06.00 Mine surveying - Slip-on pivots, slip-on caps for suspension theodolites - Connecting dimensions (5)

NA 008-11-01-01 AK Basics

DIN 21901 02.84 Mine plans; structure and list of standards; general principles (5)

DIN 21901 Bbl 1 01.12 Mine plans - Structure and list of standards -Supplement 1: Contents (6)

DIN 21901 Bbl 2 09.06 Mine plans - Structure and list of standards - Supplement 2: List of abbreviations (18)

DIN 21901 Bbl 3 07.02 Mine plans; structure and list of standards; index (23)

DIN 21901-2 11.94 Mine plans - Structure and list of standards - Part 2: Interface for EDP based transfer of symbols of mining - Specific mapping (12)

DIN 21902 10.99 Mine plants - Structure of mining specific plans (7)

DIN 21902-2 08.08 Mine plants - Structure of mining specific plans - Part 2: Completion of mine plans (11)

DIN 21903 10.95 Mine plans - Sizes and foldings (8)

DIN 21904 01.94 Mine plants; lettering (5)

DIN 21905 11.93 Mine plants; drawing principles (5)

DIN 21906 08.90 Mine plans - Subdivision of sheets (9)

DIN 21906 Bbl 1 11.91 Mine plans; subdivision of sheets; survey (19)

DIN 21906 Bbl 2 01.94 Mine plans; subdivision of sheets; survey (14)

DIN 21907 04.03 Mine plans - Graphic design of sheets (12)

DIN 21908 01.94 Mine plans - Colours (8)

NA 008-11-01-02 AK Objects on the surface, open pit mines

DIN 21909 02.02 Mine plans - Survey points and lines (9)

DIN 21910 11.14 Mine plans - Titles and boundaries (13)

DIN 21911 03.08 Mine plans; objects on the surface and contour lines (12)

DIN 21912-1 01.06 Mine plans - Opencast mining - Part 1: General requirements (12)

DIN 21912-2 01.11 Mine plans - Open cast mining - Part 2: Reconstruction (12)

DIN 21912-3 01.13 Mine plans - Open cast mining - Part 3: Operating plan (7)

NA 008-11-01-03 AK Geologic symbols and terms

DIN 21918-1 10.99 Mine plans - Mineral deposits - Part 1: Terms, classification (6)

DIN 21918-2 08.04 Mine plans - Mineral deposits - Part 2: Thicknesses (10)

DIN 21919-1 03.13 Mine plans - Stratigraphy - Part 1: General classification (10)

DIN 21919-2 12.08 Mine plans - Stratigraphy - Part 2: Regional and local subdivisions; Hard coal (8)

DIN 21919-3 11.01 Mine plans - Stratigraphy - Part 3: Regional and local subdivisions; Lignite (9)

DIN 21920-1 03.13 Mine plans - Petrography - Part 1: Generally applicable symbols - Sediments (10)

DIN 21920-2 04.96 Mine plans - Petrography - Part 2: Magmatites (10)

DIN 21920-3 04.96 Mine plans - Petrography - Part 3: Metamorphic and other lithogenetic phenomena (10)

DIN 21920-4 04.96 Mine plans - Petrography - Part 4: Minerals (6)


FB Mine Plans 11Register of Mining Standards 2015-02

DIN 21920-5 11.94 Mine plans - Petrography - Part 5: Hard coal mining (12)

DIN 21920-7 04.96 Mine plans - Petrography - Part 7: Potash and rock salt mining (7)

DIN 21921 04.96 Mine plans - Tectonic elements and figure of strata (13)

DIN 22011 11.93 Investigations of the raw material in hard-coal-mining - Treatment of exploratory drillings (17)

DIN 22012 01.94 Investigations of the raw material in hard-coal-mining - Macropetrographic classification and topographic survey of hard-coal and host rock (8)

DIN 22015 10.93 Investigations of the raw material in hardcoal-mining - Macroscopic classification and description of overburden rock (9)

NA 008-11-01-04 AK Special representations

DIN 21913-11 01.00 Mine plans - Deep mining - Part 11: Geometrical dimensions in underground workings (7)

DIN 21915 12.13 Mine plans - Technical facilities (11)

DIN 21916-1 02.07 Mine plans - Operational safety - Part 1: Ventilation system and meteorology (13)

DIN 21916-2 02.10 Mine plans - Operational safety - Part 2: Fire prevention on the surface (12)

DIN 21916-3 01.11 Mine plans - Operational safety - Part 3: Fire prevention under the surface (11)

DIN 21917 02.99 Mine plans - Strata and ground movements (13)

DIN 21917-2 03.02 Mine plans - Strata and ground movements - Part 2: Geomechanical measuring points (7)

DIN 21917-2 10.14 Mine plans - Strata and ground movements - Part 2: Geotechnical measuring points (12)

E

NA 008-11-01-05 AK Mine workings

DIN 21913-1 02.92 Mine plans; deep mining; underground workings (19)

DIN 21913-1 Bbl 1 02.92 Mine plans; underground working; storage and final deposition in mine workings (33)

DIN 21913-2 02.09 Mine plans - Deep mining - Part 2: Extraction, stowage and deposit (14)

DIN 21913-3 02.08 Mine plans - Deep mining - Part 3: Closure of underground workings (8)

DIN 21913-4 02.09 Mine plans; deep mining; Part 4: hazardous zones, zones of protective measures (11)

DIN 21913-6 11.14 Mine plans - Deep mining - Part 6: Safekeeping (10)

DIN 21913-7 01.12 Mine plans - Deep mining - Part 7: Shaft plan (10)

NA 008-11-01-06 AK Drilling, caverns, storage, final deposition

DIN 21914-1 10.05 Mine plans - Drilling and cavern - Part 1: Drilling (15)

DIN 21914-2 02.99 Mine plans - Drilling and cavern - Part 2: Brine caverns (10)


FB Fuels 12Register of Mining Standards 2015-02

12 Fuels

NA 008-12-01 AA Gaseous fuels

DIN 1340 12.90 Gaseous fuels and other gases - Types, constituents, application (7) /FABERG co-author/

DIN 1340 Bbl 1 12.90 Gaseous fuels and other gases - Types, constituents, application - Remarks on the production (5) /FABERG co-author/

DIN 1871 05.99 Road marking materials - Physical properties; German version EN 1871:2000 (13) /FABERG co-author/

DIN EN 1918-1 07.98 Gas supply systems - Underground gas storage - Part 1: Functional recommendations for storage in aquifers; German version EN 1918-1:1998 (9) /FABERG co-author/

DIN EN 1918-1 06.14 Gas infrastructure - Underground gas storage - Part 1: Functional requirements for storage in aquifers; German version prEN 1918-1:2014 (16) /FABERG co-author/

E

DIN EN 1918-2 07.98 Gas supply systems - Unterground gas storage - Part 2: Functional recommendations for storage in oil and gas fields; German version EN 1918-2:1998 (8) /FABERG co-author/

DIN EN 1918-2 06.14 Gas infrastructure - Unterground gas storage - Part 2: Functional requirements for storage in oil and gas fields; German version prEN 1918-2:2014 (15) /FABERG co-author/

E

DIN EN 1918-3 07.98 Gas supply systems - Underground gas storage - Part 3: Functional recommendations for storage in solution-mined salt cavities; German version EN 1918-3:1998 (10) /FABERG co-author/

DIN EN 1918-3 06.14 Gas infrastructure -- Underground gas storage - Part 3: Functional requirements for storage in solution-mined salt caverns; German version prEN 1918-3:2014 (17) /FABERG co-author/

E

DIN EN 1918-4 07.98 Gas supply systems - Underground gas storage - Part 4: Functional recommendations for storage in rock caverns; German version EN 1918-4:1998 (7) /FABERG co-author/

DIN EN 1918-4 06.14 Gas infrastructure - Underground gas storage - Part 4: Functional requirements for storage in rock caverns; German version prEN 1918-4:2014 (15) /FABERG co-author/

E

DIN EN 1918-5 07.98 Gas supply systems - Underground gas storage - Part 5: Functional recommendations for surface facilities; German version EN 1918-5:1998 (6) /FABERG co-author/

DIN EN 1918-5 06.14 Gas infrastructure - Underground gas storage - Part 5: Functional requirements for surface facilities; German version prEN 1918-5:2014 (12) /FABERG co-author/

E

DIN ISO 5275 10.05 Petroleum products and hydrocarbon solvents - Detection of thiols and other sulfur species - Doctor test (ISO 5275:2003) (6) /FABERG co-author/

DIN EN ISO 6141 11.06 Gas analysis - Requirements for certificates for calibration gases and gas mixtures (ISO 6141:2000); German version EN ISO 6141:2006 (8) /FABERG co-author/

DIN EN ISO 6141 08.13 Gas analysis - Contents of certificates for calibration gas mixtures (ISO/DIS 6141:2013); German version prEN ISO 6141:2013 (9) /FABERG co-author/

E

DIN EN ISO 6143 11.06 Gas analysis - Comparison methods for determining and checking the composition of calibration gas mixtures (ISO 6143:2001); German version EN ISO 6143:2006 (15) /FABERG co-author/

DIN EN ISO 6326-3 04.98 Natural gas - Determination of sulfur compounds - Part 3: Determination of hydrogen sulfide, mercaptan sulfur and carbonyl sulfide sulfur by potentiometry (ISO 6326-3:1989); German version EN ISO 6326-3:1997 (7) /FABERG co-author/



DIN EN ISO 6326-5 04.98 Natural gas - Determination of sulfur compounds - Part 5: Lingener combustion method (ISO 6326-5:1989); German version EN ISO 6326-5:1997 (9) /FABERG co-author/

DIN EN ISO 6570 12.04 Natural gas - Determination of potential hydrocarbon liquid content - Gravimetric methods (ISO 6570:2001); English version EN ISO 6570:2004 (13) /FABERG co-author/

DIN EN ISO 6974-1 11.12 Natural gas - Determination of composition and associated uncertainty by gas chromatography - Part 1: General guidelines and calculation of composition (ISO 6974-1:2012); German version EN ISO 6974-1:2012 (19) /FABERG co-author/

DIN EN ISO 6974-2 11.12 Natural gas - Determination of composition and associated uncertainty by gas chromatography - Part 2:Uncertainty calculations (ISO 6974-2:2012); German version EN ISO 6974-2:2012 (12) /FABERG co-author/

DIN EN ISO 6974-3 06.02 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two packed columns (ISO 6974-3:2000); German version EN ISO 6974-3:2001 / Note: Applies only in conjunction with DIN EN ISO 6974-1 and DIN EN ISO 6974-2 (11) /FABERG co-author/

DIN EN ISO 6974-4 06.02 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 4: Determination of nitrogen, carbon dioxide and C1- to C5- and C6+ hydrocarbons for a laboratory and on-line measuring system using two columns (ISO 6974-4:2000); German version EN ISO 6974-4:2001 / Note: Applies only in conjunction with DIN EN ISO 6974-1 and DIN EN ISO 6974-2 (10) /FABERG co-author/

DIN EN ISO 6974-5 10.14 Natural gas - Determination of composition and associated uncertainty by gas chromatography - Part 5: Isothermal method for nitrogen, carbon dioxide and C1- to C5 hydrocarbons and C6+ hydrocarbons (ISO 6974-5:2014); German version EN ISO 6974-5:2014 (15) /FABERG co-author/

DIN EN ISO 6974-6 08.05 Natural gas - Determination of composition with defined uncertainty by gas chromatography - Part 6: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and C1 to C8 hydrocarbons using three capillary columns (ISO 6974-6:2002); German version EN ISO 6974-6:2005 (12) /FABERG co-author/

DIN EN ISO 6975 09.05 Natural gas - Extended analysis - Gas-chromatographic method (ISO 6975:1997); German version EN ISO 6975:2005 (14) /FABERG co-author/

DIN EN ISO 6975/B1 09.08 Natural gas - Extended analysis - Gas-chromatographic method (ISO 6975:1997); German version EN ISO 6975:2005, Corrigendum to DIN EN ISO 6975:2005-09 (99) /FABERG co-author/

DIN EN ISO 6976 09.05 Natural gas - Calculation of calorific values, density, relative density and Wobbe index form composiotion (ISO 6976:1995 + Corrigendum 1:1997, Corrigendum 2:1997, Corrigendum 3:1999); German version EN ISO 6976:2005 (22) /FABERG co-author/

DIN EN ISO 6978-1 09.05 Natural gas - Determination of mercury - Part 1: Sampling of mercury by chemisorption on iodine (ISO 6978-1:2003); German version EN ISO 6978-1:2005 (12) /FABERG co-author/

DIN EN ISO 6978-2 09.05 Natural gas - Determination of mercury - Part 2: Sampling of mercury by amalgamation on gold/platinum alloy (ISO 6978-2:2003); German version EN ISO 6978-2:2005 (12) /FABERG co-author/

DIN EN ISO 10101-1 07.98 Natural gas - Determination of water by the Karl Fischer method - Part 1: Introduction (ISO 10101-1:1993); German version EN ISO 10101-1:1998 (6) /FABERG co-author/

DIN EN ISO 10101-2 07.98 Natural gas - Determination of water by the Karl Fischer method - Part 2: Tritation procedure (ISO 10101-2:1993); German version EN ISO 10101-2:1998 (8) /FABERG co-author/

DIN EN ISO 10101-3 07.98 Natural gas - Determination of water by the Karl Fischer method - Part 3: Coulometric procedure (ISO 10101-3:1993); German version EN ISO 10101-3:1998 (8) /FABERG co-author/



DIN EN ISO 10723 04.13 Natural gas - Performance evaluation for analytical systems (ISO 10723:2012); German version EN ISO 10723:2012 (17) /FABERG co-author/

DIN EN ISO 11541 02.03 Natural gas - Determination of water content at high pressure (ISO 11541:1997); German version prEN ISO 11541:2002 (7) /FABERG co-author/

DIN EN ISO 12213-1 01.10 Natural gas - Calculation of compression factor - Part 1: Introduction and guidelines (ISO 12213-1:2006); German version EN ISO 12213-1:2009 (11) /FABERG co-author/

DIN EN ISO 12213-2 01.10 Natural gas - Calculation of compression factor - Part 2: Calculation using molar-composition analysis (ISO 12213-2:2006); German version EN ISO 12213-2:2009 (16) /FABERG co-author/

DIN EN ISO 12213-3 01.10 Natural gas - Calculation of compression factor - Part 3: Calculation using physical properties (ISO 12213-3:2006); German version EN ISO 12213-3:2009 (17) /FABERG co-author/

DIN 12473-1 04.76 Laboratory glassware - gas sampling tubes with straight bore stopcocks (4) /FABERG co-author/

DIN 12473-2 04.76 Laboratory glassware - gas sampling tubes with V-bore stopcocks (4) /FABERG co-author/

DIN EN ISO 14111 06.00 Naturalgas - Guidelines to traceability in analyses (ISO 14111:1997); German version EN ISO 14111:1999 (13) /FABERG co-author/

DIN EN ISO 18453 01.06 Natural gas - Correlation between water content and water dew point (ISO 18453:2004); German version prEN 18453:2005 (13) /FABERG co-author/

BB 22061-1 04.82 Steinkohlenbergbau - Gase unter Tage - Anwendungsbereich, Zweck, Begriffe und Allgemeines (1)

BB 22061-2 04.82 Steinkohlenbergbau - Gase unter Tage - Probenahme (4)

BB 22061-3 04.82 Steinkohlenbergbau - Gase unter Tage - Analyse nach physikalischen Verfahren im Laboratorium (2)

DIN 51400-4 04.00 Testing of mineral oils and fuels - Determination of sulfur content (total sulfur) - Part 4: Combustion according to the Lingener method, visual titration, turbidmetric-titration (6) /FABERG co-author/

DIN 51851 04.80 Testing of gaseous fuels and other gases; calculation of reduced gas volume (4) /FABERG co-author/

DIN 51853 12.11 Testing of fuel gases - Sampling (11) /FABERG co-author/

DIN 51854 09.93 Testing of gaseous fuels and other gases; determination of ammonia content (5) /FABERG co-author/

DIN 51855-1 09.11 Testing of gaseous fuels and other gases - Determination of the content of sulphur compounds - Part 1: Field of application, terms (5) /FABERG co-author/

DIN 51855-4 06.95 Testing of gaseous fuels and other gases - Determination of sulphur compounds content - Part 4: Content of hydrogen sulfide, zinc acetate method (5) /FABERG co-author/

DIN 51855-6 09.00 Testing of gaseous fuels and other technical gases - Determination of sulfur compounds content - Part 6: Content of hydrogen sulfide, mercaptan sulfur and carbonylsulfide sulfur; potentiometric method (6) /FABERG co-author/

DIN 51855-7 12.86 Testing of gaseous fuels and other gases; determination of the content of sulfur compounds; gaschromatographic determination of the content of odoriferous sulfur compounds using an electrochemical detector (5) /FABERG co-author/

DIN 51855-8 06.97 Testing of gaseous fuels and other gases - Determination of sulfur compounds content - Part 8: Gaschromatographic determination of dihydrogen sulfide, carbonyl sulfide and other sulfur compounds using specific detectors (7) /FABERG co-author/

DIN 51857 03.97 Gaseous fuels and other gases - Calculation of calorific value, density, relative density and Wobbe index of pure gases and gas mixtures (9) /FABERG co-author/

DIN 51862 09.82 Testing of gaseous fuels and other gases; determination of naphthalene content (crude naphthalene) (5) /FABERG co-author/



DIN 51863-1 09.83 Testing of gaseous fuels and other gases; determination of hydrogen cyanide content; nickel carbonate method (6) /FABERG co-author/

DIN 51863-2 09.83 Testing of gaseous fuels and other gases; determination of hydrogen cyanide content; bromide cyanogen method (5) /FABERG co-author/

DIN 51864 09.86 Testing of gaseous fuels and other gases; determination of nitrogen monoxide content; Saltzman method (5) /FABERG co-author/

DIN 51865-1 09.98 Testing of gaseous fuels and other gases - Determination of mercury content - Part 1: Chemisorption on Iodine, atomic absorption spectrometry (AAS) (6) /FABERG co-author/

DIN 51865-2 10.00 Testing of gaseous fuels and other gases - Determination of mercury content - Part 2: Combustion using the modified Lingener method; Atomic absorption spectrometry (AAS) (6) /FABERG co-author/

DIN 51865-3 02.98 Testing of gaseous fuels and other gases - Determination of mercury content - Part 3: Absorption in solutions, atomic absorption spectrometry (AAS) (6) /FABERG co-author/

DIN 51869 09.00 Testing of gaseous fuels and other gases; determination of the main components, general statements (5) /FABERG co-author/

DIN 51870 04.81 Testing of gaseaus fuels and other gases; determination of relative density according to the balance method and calculation of density (6) /FABERG co-author/

DIN 51871 12.85 Testing of gaseous fuels and other technical gases; determination of dew point of water vapour; method of means of cooled mirror (5) /FABERG co-author/

DIN 51872-4 06.90 Testing of gaseous fuels and other gases; determination of the components; gaschromatographic procedure (6) /FABERG co-author/

DIN 51872-5 08.96 Testing of gaseous fuels and other gases - Determination of the components - Part 5: Capillary gaschromatographic procedure (8) /FABERG co-author/

NA 008-12-02 AA Testing of solid fuels

DIN 22022-1 07.14 Solid fuels - Determination of contents of trace elements - Part 1: General rules, sampling and sample preparation - Preparation of samples for the analyses (dissolution method) (7)

DIN 22022-2 02.01 Solid fuels - Determination of contents of trace elements - Part 2: ICP-OES (5)

DIN 22022-3 02.01 Solid fuels - Determination of trace elements - Part 3: AAS-flame method (5)

DIN 22022-4 02.01 Solid fuels - Determination of contents of trace elements - Part 4: Atomic absorption spectrometry applying the flameless hydride system or the cold-vapour-method (5)

DIN 22022-5 02.01 Solid fuels - Determination of trace elements - Part 5: Atomic absorption spectrometry applying the electrothermal atomization (5)

DIN 22022-6 12.01 Solid fuels - Determination of trace elements - Part 6: Evaluation and declaration of results (7)

DIN 22022-7 07.14 Solid fuels - Determination of contents of trace elements - Part 7: ICP-MS (8)

DIN 51700 07.10 Testing of solid fuels - Generalities and index of methods of test (13)

DIN 51701-1 12.07 Testing of solid fuels - Sampling and sample preparation - Part 1: Definitions (6)

DIN 51701-2 09.06 Testing of solid fuels - Sampling and sample preparation - Part 2: Sampling (12)

DIN 51701-3 09.06 Testing of solid fuels - Sampling and sample preparation - Part 3: Sample preparation (9)

DIN 51701-4 09.06 Testing of solid fuels - Sampling and sample preparation - Part 4: Equipment (10)

DIN 51701-5 03.08 Testing of solid fuels - Sampling and sample preparation - Part 5: Testing of precision (12)

DIN 51705 06.01 Testing of solid fuels - Determination of the bulk density of solid fuels (5)

DIN 51717 07.94 Testing of solid fuels; determination of mechanical strength of coke (6)



DIN 51718 06.02 Testing of solid fuels - Determination of the water content and the moisture of analysis sample (6)

DIN 51719 07.97 Testing of solid fuels - Solid mineral fuels - Determination of ash content (5)

DIN 51720 03.01 Testing of solid fuels - Determination of volatile matter content (7)

DIN 51721 08.01 Testing of solid fuels - Determination of carbon content and hydrogen content - Radmacher-Hoverath method (6)

DIN 51722-1 07.90 Testing of solid fuels; determination of nitrogen content; semi-micro Kjeldahl method (5)

DIN 51723 06.02 Testing of solid fuels - Determination of fluorine content (7)

DIN 51724-1 07.12 Testing of solid fuels - Determination of sulfur content - Part 1: Total sulfur (9)

DIN 51724-2 06.99 Testing of solid fuels - Determination of sulfur content - Part 2: Species (7)

DIN 51724-3 07.12 Solid minerals fuels - Determination of sulfur content - Part 3: Instrumental methods (6)

DIN 51725 06.04 Testing of solid fuels - Determination of the phosphorus content (7)

DIN 51726 06.04 Testing of solid fuels - Determination of the carbonate carbon dioxide content (7)

DIN 51727 11.11 Testing of solid fuels - Determination of chlorine content (6)

DIN 51729-8 05.01 Solid fuels - Determination of chemical composition of fuel ash - Part 8: Determination of soda and potash (Na<(Index)2>O, K<(Index)2>O) contents (5)

DIN 51729-10 04.11 Testing of solid fuels - Determination of chemical composition of fuel ash - Part 10: X-Ray Fluorescence Analysis (8)

DIN 51729-11 11.98 Testing of solid fuels - Determination of chemical composition of fuel ash - Part 11: Determination by inductively coupled plasma emission spectrometry (ICP-OES) (5)

DIN 51730 09.07 Testing of solid fuels - Determination of fusibility of fuel ash (10)

DIN 51731 10.96 Testing of solid fuels - Compressed untreated wood - Requirements and testing (5) /FABERG co-author/

DIN 51732 07.14 Testing of solid mineral fuels - Determination of total carbon, hydrogen and nitrogen - Instumental methods (7)

DIN 51733 12.08 Testing of solid mineral fuels - Ultimate analysis and calculation of oxygen content (6)

DIN 51734 12.08 Testing of solid mineral fuels - Proximate analysis and calculation of fixed carbon (6)

DIN 51735 02.09 Testing of solid mineral fuels - Determination of plastic properties of coal using the Gieseler plastometer (9)

DIN 51739 05.98 Testing of solid fuels - Determination of the dilatation of coal (8)

DIN 51741 10.98 Testing of solid fuels - Determination of the crucible swelling number of coal (6)

DIN 51742 07.01 Testing of solid fuels - Determination of Hardgrove grindability index of hard coal (7)

DIN 51900-1/B1 02.04 Corrigenda to DIN 51900-1:2000-04 (0)

DIN 51900-1 04.00 Testing of solid and liquid fuels - Determination of gross calorific value by the bomb calorimeter and calculation of net calorific value - Part 1: Principles, apparatus, methods (12)

DIN 51900-2 05.03 Testing of solid and liquid fuels - Determination of the gross calorific value by the bomb calorimeter and calculation of the net calorific value - Method using isoperibol or static jacket calorimeter (8)

DIN 51900-3 01.05 Testing of solid and liquid fuels - Determination of the gross calorific value by the bomb calorimeter and calculation of net calorific value - Part 3: Method Using Adiabatic Jacket (8)


FB Cables, Telecontrol and Other Electrical Equipment 14Register of Mining Standards 2015-02

14 Cables, Telecontrol and Other Electrical Equipment

14 Cables, telecontrol and other electrical equipment

BB 22000-1 11.75 Größen und Einheiten - Teil 1: Einheiten - Allgemeine Grundlagen (3)

BB 22000-2 02.76 Größen und Einheiten - Teil 2: Masse, Kraft, Gewicht (1)

BB 22000-3 02.76 Größen und Einheiten - Teil 3: Temperatur, Druck (2)

BB 22442-1 03.03 Elektromagnetische Verträglichkeit für Anlagen im Steinkohlenbergbau - Teil 1: Grundlagen (4)

BB 22442-2 03.03 Elektromagnetische Verträglichkeit für Anlagen im Steinkohlenbergbau - Teil 2: Störaussendungs- und Störfestigkeits-Grenzwerte (4)

BB 22443 08.88 Geräte und Anlagen der Fernwirktechnik - Dokumentation von Softwaresystemen (4)

BB 22444-1 02.76 Geräte und Anlagen der Fernwirktechnik - Begriffe (2)

BB 22444-2 10.82 Geräte und Anlagen der Fernwirktechnik - Anforderung und Prüfung (3)

BB 22444-3 07.87 Geräte und Anlagen der Fernwirktechnik - Schnittstellen (3)

BB 22444-4 07.87 Geräte und Anlagen der Fernwirktechnik - Standardaufbau einer Telegrammschnittstelle zwischen Fernwirkstation und Prozeßrechner (3)

BB 22444-4 Bbl 1 07.87 Geräte und Anlagen der Fernwirktechnik - Standard für die serielle Datenübertragung im Nahbereich (2)

BB 22444-4 Bbl 2 07.87 Geräte und Anlagen der Fernwirktechnik - Ablauf der Datenübertragung (1)

BB 22444-4 Bbl 3 07.87 Geräte und Anlagen der Fernwirktechnik - Ablaufbeispiel der Datenübertragung (1)

BB 22445 10.73 Wassergekühlte polumschaltbare Drehstrommotoren, Bauform B5 - Anbaumaße und Zuordnung der Leistungen bei Ausführung in Zündschutzart (Sch) d (1)

BB 22446 05.87 Geräte und Anlagen der Fernwirktechnik - Frequenzbereiche für Funkanlagen (2)

BB 22450-1 06.88 Grubenkabel für Fernmelde- und Informationsanlagen - Auswahl für den Steinkohlenbergbau unter Tage (2)

BB 22450-2/A1 12.00 Leitungen für Fernmelde- und Informationsverarbeitungsanlagen - Auswahl für den Steinkohlenbergbau unter Tage - Änderung 1 (2)

BB 22450-2 06.88 Leitungen für Fernmelde- und Informationsanlagen - Auswahl für den Steinkohlenbergbau unter Tage (2)

BB 22450-3 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 3: Bewehrte Leitung L-2YYQY (blau) (4)

BB 22450-4 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 4: Zugfeste, geschirmte Leitung L-2Y(C)Y(ZG)Y (blau) (4)

BB 22450-5 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 5: Zugfeste, geschirmte Leitungen L-2YYC(ZG)Y (blau) (4)

BB 22450-6 06.99 Grubenkabel für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 6: Bewehrtes Grubenkabel G-2YYYBY (blau) mit Paaren (4)

BB 22450-7 06.99 Grubenkabel für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 7: Bewehrtes Grubenkabel G-2YY(Z)Y (blau) mit Paaren (4)

BB 22450-8 06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für eigensichere elektrische Anlagen - Teil 8: Zugfeste Leitung L-YY(ZG)Y (blau) (4)

DIN 43620-5 06.86 Low-voltage high-rupturing capacity fuses with blade contacts; LV HRC fuse links for AV 1000 V (5) /FABERG co-author/


FB Solid mineral fuels ISO/TC 27Register of Mining Standards 2015-02

ISO/TC 27 Solid mineral fuels

ISO/TC 27 Solid mineral fuels

ISO 502 02.82 Coal - Determination of caking power - Gray-King coke test

ISO 1213-2 04.92 Solid mineral fuels - Vocabulary - Part 2: Terms relating to sampling, testing and analysis

ISO 1953 07.94 Hard coal - Size analysis by sieving

ISO/TC 27/WG 18 Classification of coals

ISO 11760 02.05 Classification of coals

ISO/TC 27/SC 1 Coal preparation - Terminology and performance

ISO 561 12.89 Coal preparation plant - Graphical symbols

ISO 923 05.00 Coal cleaning equipment - Performance evaluation

ISO 924 12.89 Coal preparation plant - Principles and conventions for flowsheets

ISO 1213-1 12.93 Solid mineral fuels - Vocabulary - Part 1: Terms relating to coal preparation

ISO/DIS 1953 02.13 Hard coal - Size analysis by sieving

ISO 7936 04.92 Hard coal - Determination and presentation of float and sink characteristics - General directions for apparatus and procedures

ISO 8833 11.89 Magnetite for use in coal preparation - Test methods

ISO 8858-1 09.90 Hard coal - Froth flotation testing - Part 1: Laboratory procedure

ISO 8858-2 08.04 Hard coal - Froth flotation testing - Part 2: Sequential evaluation

ISO 8858-3 08.04 Hard coal - Froth flotation testing - Part 3: Release evaluation

ISO 10086-1 06.00 Coal - Methods for evalution flocculants for use in coal preparation - Part 1: Basic parameters

ISO 10086-2 01.04 Coal - Methods for evaluating flocculants for use in coal preparation - Part 2: Flocculants as filter aids in rotary vacuum filtration systems

ISO 10752 05.94 Coal sizing equipment - Performance evaluation

ISO 10753 02.94 Coal preparation plant - Assessment of the liability to breakdown in water of materials associated with coal seams

ISO 15117-1 05.04 Coal flow properties - Part 1: Bin flow

ISO 20905 07.04 Coal preparation - Determination of dust/moisture relationship for coal

ISO 23499 07.13 Coal - Determination of bulk density for the use in charging of coke ovens

ISO/TC 27/SC 3 Coke

ISO 556 11.80 Coke (greater than 20 mm in size) - Determination of mechanical strength

ISO 567 07.95 Coke - Determination of bulk density in a small container

ISO 616 11.95 Coke - Determination of shatter indices

ISO 728 11.95 Coke (nominal top size greater than 20 mm) - Size analysis by sieving

ISO 1013 07.95 Coke - Determination of bulk density in a large container

ISO 1014 09.85 Coke - Determination of true relative density, apparent relative density and porosity

ISO 2325 02.86 Coke - Size analysis (Nominal top size 20 mm or less)

ISO 18894 04.06 Coke - Determination of coke reactivity index (CRI) and coke strength after reaction (CSR)



ISO/TC 27/SC 4 Sampling

ISO 5069-1 11.83 Brown coals and lignites - Principles of sampling - Part 1: Sampling for determination of moisture content and for general analysis

ISO 5069-2 12.83 Brown coals and lignites - Principles of sampling - Part 2: Sample preparation for determination of moisture content and for general analysis

ISO 9931 12.91 Coal - Sampling of pulverized coal conveyed by gases in direct fire coal systems

ISO 21398 06.07 Hard coal and coke - Guidance to the inspection of mechanical sampling systems

ISO/TC 27/SC 4/WG 1 Sampling of coal

ISO 13909-1 12.01 Hard coal and coke - Mechanical sampling - Part 1: General introduction

ISO 13909-2 12.01 Hard coal and coke - Mechanical sampling - Part 2: Coal - Sampling from moving streams

ISO 13909-3 12.01 Hard coal and coke - Mechanical sampling - Part 3: Coal - Sampling from stationary lots

ISO 13909-4 12.01 Hard coal and coke - Mechanical sampling - Part 4: Coal - Preparation of test samples

ISO/TC 27/SC 4/WG 2 Sampling of coke

ISO 13909-5 12.01 Hard coal and coke - Mechanical sampling - Part 5: Coke - Sampling from moving streams

ISO 13909-6 12.01 Hard coal and coke - Mechanical sampling - Part 6: Coke - Preparation of test samples

ISO/TC 27/SC 4/WG 5 Methods for test for bias

ISO 13909-7 12.01 Hard coal and coke - Mechanical sampling - Part 7: Methods for determining the precision of sampling, sample preparation and testing

ISO 13909-8 12.01 Hard coal and coke - Mechanical sampling - Part 8: Methods of testing for bias

ISO/TC 27/SC 4/WG 6 Sampling of coal seams

ISO 14180 08.98 Solid mineral fuels - Guidance on the sampling of coal seams

ISO/TC 27/SC 4/WG 7 Manual Sampling

ISO 18283 09.06 Hard coal and coke - Manual sampling

ISO 18283:2006/Cor 1

04.09 ISO 18283 Technical Corrigendum 1

ISO/TC 27/SC 4/WG 8 Sampling of coal slurries

ISO 20904 10.06 Hard coal - Sampling of slurries

ISO/TC 27/SC 4/WG 10 Revision of ISO 13909

ISO/DIS 13909-1 07.14 Hard coal and coke - Mechanical sampling - Part 1: General introduction

ISO/DIS 13909-2 07.14 Hard coal and coke - Mechanical sampling - Part 2: Coal - Sampling from moving streams

ISO/DIS 13909-3 07.14 Hard coal and coke - Mechanical sampling - Part 3: Coal - Sampling from stationary lots

ISO/DIS 13909-5 07.14 Hard coal and coke - Mechanical sampling - Part 5: Coke - Sampling from moving streams

ISO/DIS 13909-6 07.14 Hard coal and coke - Mechanical sampling - Part 6: Coke - Preparation of test samples

ISO/DIS 13909-7 07.14 Hard coal and coke - Mechanical sampling - Part 7: Methods for determining the precision of sampling, sample preparation and testing



ISO/DIS 13909-8 07.14 Hard coal and coke - Mechanical sampling - Part 8: Methods of testing for bias

ISO/TC 27/SC 5 Methods of analysis

ISO 12900 12.97 Hard coal - Determination of abrasiveness

ISO/DIS 12900 10.14 Hard coal - Determination of abrasiveness

ISO/TC 27/SC 5/WG 1 Moisture, volatile matter and ash

ISO 562 06.10 Hard coal and coke - Determination of volatile matter

ISO 579 05.13 Coke - Determination of total moisture

ISO 589 11.08 Hard coal - Determination of total moisture

ISO 687 06.10 Solid mineral fuels - Coke - Determination of moisture in the general analysis test sample

ISO 1018 11.75 Hard coal - Determination of moisture-holding capacity

ISO 1170 07.13 Coal and coke - Calculation of analyses to different bases

ISO 1171 06.10 Solid mineral fuels - Determination of ash

ISO 11722 07.13 Solid mineral fuels - Hard coal - Determination of moisture in the general analysis test sample by drying in nitrogen

ISO 17246 06.10 Coal - Proximate analysis

ISO/TC 27/SC 5/WG 2 Carbon, hydrogen, nitrogen, oxygen and sulfur

ISO 157 06.96 Coal - Determination of forms of sulfur

ISO 334 10.13 Solid mineral fuels - Determination of total sulfur - Eschka method

ISO 587 05.97 Solid mineral fuels - Determination of chlorine using Eschka mixture

ISO 609 02.96 Solid mineral fuels - Determination of carbon and hydrogen - High temperature combustion method

ISO 609/COR 1 07.96 Solid mineral fuels - Determination of carbon and hydrogen - High temperature combustion method; Technical corrigendum 1

ISO 625/COR 1 07.96 Solid mineral fuels - Determination of carbon and hydrogen - Liebig method; Technical Corrigendum 1

ISO 625 02.96 Solid mineral fuels - Determination of carbon and hydrogen - Liebig method

ISO 925 05.97 Solid mineral fuels - Determination of carbon dioxide content - Gravimetric method

ISO 17247 07.13 Coal - Ultimate Analysis

ISO/TS 18806 12.14 Solid mineral fuels - Determination of chlorine content

ISO 19579 10.06 Solid mineral fuels - Determination of sulfur by IR spectrometry

ISO 29541 10.10 Solid minerals fuels - Determination of total carbon, hydrogen and nitrogen content - Instrumental method

ISO/TC 27/SC 5/WG 7 Brown coal and lignites

ISO 647 11.74 Brown coals and lignites - Determination of the yields of tar, water, gas and coke residue by low temperature distillation

ISO 975 05.13 Brown coals and lignites - Determination of yield of benzene-soluble extract - Semi-automatic method

ISO 1017 12.06 Brown coals and lignites - Determination of acetone-soluble material ("resinous substance") in benzene-soluble extract

ISO 2950 02.74 Brown coals and lignites - Classification by types on the basis of total moisture content and tar yield

ISO 5068-1 01.07 Brown coals and lignites - Determination of moisture content - Part 1: Indirect gravimetric method for total moisture



ISO 5068-2 01.07 Brown coals and lignites - Determination of moisture content - Part 2: Indirect gravimetric method for moisture in the analysis sample

ISO 5071-1 05.13 Brown coals and lignites - Determination of the volatile matter in the analysis sample - Part 1: Two- furnace method

ISO 5072 05.13 Hard colas, brown coals and lignites - Determination of true relative density and apparent relative density

ISO 5073 05.13 Brown coals and lignites - Determination of humic acids

ISO/TC 27/SC 5/WG 8 Major, minor and trace elements in coal and coal residues

ISO 602 02.83 Coal - Determination of mineral matter

ISO/FDIS 602 12.14 Coal - Determination of mineral matter

ISO 622 08.81 Solid mineral fuels - Determination of phosphorus content - Reduced molybdophosphate photometric method

ISO 1952 08.08 Solid mineral fuels - Determination of extractable metals in dilute hydrochloric acid

ISO 11723 11.04 Solid mineral fuels - Determination of arsenic and selenium - Eschka's mixture and hydride generation method

ISO 11724 11.04 Solid mineral fuels - Determination of total fluorine in coal, coke and fly ash

ISO/TS 13605 05.12 Solid mineral fuel - Major and minor elements in hard coal ash and coke ash - Wavelength dispersive x-ray fluorescence spectrometric method

ISO 15237 12.03 Solid minerals fuels - Determination of total mercury content of coal

ISO 15238 12.03 Solid mineral fuels - Determination of total cadmium content of coal

ISO 23380 09.13 Selection of methods for the determination of trace elements in coal

ISO/TC 27/SC 5/WG 9 Guidelines for the validation of methods

ISO 11726 08.04 Solid minerals fuels - Guidelines for the validation of alternative methods of analysis

ISO/TC 27/SC 5/WG 10 Plastic properties of coal

ISO 349 01.75 Hard coal - Audibert-Arnu dilatometer test

ISO 501 09.12 Hard coal - Determination of the crucible swelling number

ISO 8264 11.89 Hard coal - Determination of the swelling properties using a dilatometer

ISO 10329 02.09 Coal - Determination of plastic properties - Constant-torque Gieseler plastometer method

ISO 15585 01.06 Solid mineral fuels - Hard Coal - Determination of caking index

ISO 23873 11.10 Hard coal - Method for the measurement of the swelling of hard coal using a dilatometer

ISO/TC 27/SC 5/WG 11 On-line analyzers

ISO 15239 04.05 Solid mineral fuels - Evaluation of the measurement performance of on-line analyzers

ISO/TC 27/SC 5/WG 12 Miscellaneous Methods

ISO 540 05.08 Hard coal and coke - Determination of ash fusibility

ISO 1928 05.09 Solid mineral fuels - Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value

ISO/DIS 5074 10.14 Hard coal - Determination of Hardgrove grindability index

ISO 5074 12.94 Hard coal - Determination of Hardgrove grindability index



ISO/TC 27/SC 5/WG 14 Petrographic analysis of coal

ISO 7404-1 10.94 Methods for the petrographic analysis of bitumious coal and anthracite - Part 1: Vocabulary

ISO 7404-2 10.09 Methods for the petrographic analysis of coals - Part 2: Methods of preparing coal samples

ISO 7404-3 10.09 Methods for the petrographic analysis of coals - Part 3: Method of determining maceral group composition

ISO 7404-4 12.88 Methods for the petrographic analysis of bitumious coal and anthracite - Part 4: Method of determining microlithotype, carbominerite and minerite composition

ISO 7404-5 10.09 Methods for the petrographic analysis of coals - Part 5: Method of determining microscopically the reflectance of vitrinite


FB Mining ISO/TC 82Register of Mining Standards 2015-02

ISO/TC 82 Mining

ISO/TC 82 Mining

ISO 610 08.90 High-tensile steel chains (round link) for chain conveyors and coal ploughs

ISO 710-1 09.74 Graphical symbols for use on detailed maps, plans and geological cross-sections - Part 1: General rules of representation

ISO 710-2 09.74 Graphical symbols for use on detailed maps, plans and geological cross-sections - Part 2: Representation of sedimentary rocks

ISO 710-3 09.74 Graphical symbols for use on detailed maps, plans and geological cross-sections - Part 3: Representation of magmatic rocks

ISO 710-4 04.82 Graphical symbols for use on detailed maps, plans and geological cross-sections - Part 4: Representation of metamorphic rocks

ISO 710-5 07.89 Graphical symbols for use on detailed maps, plans and geological cross-sections - Part 5: Representation of minerals

ISO 710-6 06.84 Graphical symbols for use on detailed maps, plans and geological cross-sections - Part 6: Representation of contact rocks and rocks which have undergone metasomatic, pneumatolytic or hydrothermal transformation or transformation by weathering

ISO 710-7 08.84 Graphical symbols for use on detailed maps, plans and geological cross-sections - Part 7: Tectonic symbols

ISO 721 01.91 Rock drilling equipment - Integral stems

ISO 722 02.91 Rock drilling equipment - Hollow drill steels in bar form, hexagonal and round

ISO 723 02.91 Rock drilling equipment - Forged collared shanks and corresponding chuck bushings for hollow hexagonal drill steels

ISO 1082 08.90 Mining - Shackle type connector units for chain conveyors

ISO 1717 06.74 Rock drilling - Rotary drill-rods and rotary drill-bits for dry drilling - Connecting dimensions

ISO 1718 01.91 Rock drilling equipment - Drill rods with tapered connection for percussive drilling

ISO 1721 08.74 Rock drilling - Extension drill-steel equipment for percussive long-hole drilling - Reverse-buttress-threaded equipment 1 1/16 and 1 1/14 (27 and 32 mm)

ISO 1722 09.74 Rock drilling - Extension drill-steel equipment for percussive lang-hole drilling - Reverse-buttress-threaded equipment 1 1/2 to 2 1/2 in (38 to 64 mm)

ISO 3154 06.88 Stranded wire ropes for mine hoisting - Technical delivery requirements

ISO 3155 04.76 Stranded wire ropes for mine hoisting - Fibre components - Characteristics and tests

ISO 3156 07.76 Stranded wire ropes for mine hoisting - Impregnating compounds, lubricants and service dressings - Characteristics and tests

ISO 3551-1 07.92 Rotary core diamond drilling equipment - System A - Part 1: Metric units

ISO 3551-2 07.92 Rotary core diamond drilling equipment - System A - Part 2: Inch units

ISO 3552-1 07.92 Rotary core diamond drilling equipment - System B - Part 3: Metric units

ISO 3552-2 07.92 Rotary core diamond drilling equipment - System B - Part 4: Inch units

ISO 5612 08.90 Mining - Scraper bars for chain conveyors

ISO 5613 06.84 Mining - Drive sprocket assemblies for chain conveyors

ISO 5614 06.88 Locked coil wire ropes for mine hoisting - Technical delivery requirements

ISO/TR 8865 12.90 Mining - guidance on methods of verifying dimensions of sprocket assemblies for chain conveyors

ISO 8866 05.91 Rotary core diamond drilling equipment - System C

ISO 8866/Cor 1 08.91 Rotary core diamond drilling equipment - System C; technical corrigendum 1

ISO 8866/Cor 2 01.92 Rotary core diamond drilling equipment - System C; technical corrigendum 2


FB Mining ISO/TC 82Register of Mining Standards 2015-02

ISO 10097-1 10.99 Wireline diamond core drilling equipment - System A - Part 1: Metric units

ISO 10097-2 10.99 Wireline diamond core drilling equipment - System A - Part 2: Inch units

ISO 10098 10.92 Wireline diamond core drilling equipment - System CSSK

ISO 10207/Cor 1 04.91 Rock drilling equipment - Rope threaded drill steel equipment for percussive drilling, nominal sizes 22 mm to 38 mm; technical corrigendum 1

ISO 10207 02.91 Rock drilling equipment - Rope threaded drill steel equipment for percussive drilling, nominal sizes 22 mm to 38 mm

ISO 10208 02.91 Rock drilling equipment - Left-hand rope threads


Register of Mining Standards - سازمان نظام ...ime.org.ir/ad/os261/bergverze.pdf ·...

Documents

Transcript of Register of Mining Standards - سازمان نظام ...ime.org.ir/ad/os261/bergverze.pdf ·...