RADIO TEST REPORT (AS/NZS 4268) - Logitech No.: RC990901E04 1 Report Format Version 3.0.1 RADIO TEST...

Report No.: RC990901E04 1 Report Format Version 3.0.1

RADIO TEST REPORT (AS/NZS 4268)

REPORT NO.: RC990901E04

MODEL NO.: Y-R0016

RECEIVED: Sep. 01, 2010

TESTED: Sep. 01 to 02, 2010

ISSUED: Sep. 08, 2010

APPLICANT: LOGITECH FAR EAST LTD.

ADDRESS: #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C.

ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory

LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan

This test report consists of 34 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by any government agencies. The test results in the report only apply to the tested sample.


Table of Contents

1. CERTIFICATION............................................................................................................... 4

2. SUMMARY OF TEST RESULTS....................................................................................... 5

2.1 TEST INSTRUMENTS ................................................................................................ 6

2.2 MEASUREMENT UNCERTAINTY ............................................................................... 7

3. GENERAL INFORMATION................................................................................................ 8

3.1 GENERAL DESCRIPTION OF EUT............................................................................. 8

3.2 DESCRIPTION OF TEST MODES............................................................................... 9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .......................... 9

3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ..............................................11

3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................12

3.1 CONFIGURATION OF SYSTEM UNDER TEST..........................................................12

4. TEST PROCEDURES AND RESULTS ............................................................................13

TRANSMITTER PARAMETERS ..........................................................................................13

4.1 RF OUTPUT POWER (EIRP).....................................................................................13 4.1.1 LIMITS OF RF OUTPUT POWER AT THE HIGHEST POWER LEVEL..................13 4.1.2 TEST PROCEDURES..........................................................................................13 4.1.3 DEVIATION FROM TEST STANDARD.................................................................13 4.1.4 TEST SETUP ......................................................................................................13 4.1.5 TEST RESULTS ..................................................................................................14

4.2 MEASUREMENT RADIATED SPURIOUS EMISSION................................................15 4.2.1 LIMIT OF MEASUREMENT RADIATED SPURIOUS EMISSION ...........................15 4.2.2 TEST PROCEDURES..........................................................................................15 4.2.3 TEST SETUP ......................................................................................................15 4.2.4 TEST RESULTS ..................................................................................................16

4.3 OPERATING FREQUENCIES RANGE ......................................................................18 4.3.1 LIMIT OF PERMITTED RANGE OF OPERATING FREQUENCIES .......................18 4.3.2 TEST PROCEDURES..........................................................................................18 4.3.3 TEST SETUP ......................................................................................................18 4.3.4 TEST RESULTS ..................................................................................................19

4.4 EMISSION BANDWIDTH...........................................................................................20 4.4.1 LIMIT OF EMISSION BANDWIDTH .....................................................................20 4.4.2 TEST PROCEDURE............................................................................................20 4.4.3 DEVIATION FROM TEST STANDARD ................................................................20 4.4.4 TEST SETUP ......................................................................................................20


4.4.5 TEST RESULTS..................................................................................................21 4.5 6dB BANDWIDTH MEASUREMENT ..........................................................................22

4.5.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT...................................................22 4.5.2 TEST PROCEDURE............................................................................................22 4.5.3 DEVIATION FROM TEST STANDARD ................................................................22 4.5.4 TEST SETUP ......................................................................................................22 4.5.5 TEST RESULTS..................................................................................................23

4.6 POWER SPECTRAL DENSITY MEASUREMENT ......................................................24 4.6.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT..............................24 4.6.2 TEST PROCEDURE............................................................................................24 4.6.3 DEVIATION FROM TEST STANDARD ................................................................24 4.6.4 TEST SETUP ......................................................................................................24 4.6.5 TEST RESULTS..................................................................................................25

4.7 CONDUCTED - OUT BAND EMISSIONS MEASUREMENT ........................................26 4.7.1 LIMITS OF CONDUCTED - OUT BAND EMISSIONS MEASUREMENT ...............26 4.7.2 TEST PROCEDURE............................................................................................26 4.7.3 DEVIATION FROM TEST STANDARD ................................................................26 4.7.4 TEST SETUP ......................................................................................................26 4.7.5 TEST RESULTS..................................................................................................26

4.7.5.1 TEST RESULTS...............................................................................................27 RECEIVER PARAMETERS.................................................................................................29

4.8 MEASUREMENT RADIATED SPURIOUS EMISSION................................................29 4.8.1 LIMIT OF MEASUREMENT RADIATED SPURIOUS EMISSION ...........................29 4.8.2 TEST PROCEDURES..........................................................................................29 4.8.3 TEST SETUP ......................................................................................................29 4.8.4 TEST RESULTS ..................................................................................................30

5. PHOTOGRAPHS OF THE TEST CONFIGURATION ........................................................32

6. INFORMATION ON THE TESTING LABORATORIES ......................................................34


1. CERTIFICATION

PRODUCT: 2.4GHz Cordless keyboard

MODEL NO.: Y-R0016

BRAND: Logitech

APPLICANT: LOGITECH FAR EAST LTD.

TESTED: Sep. 01 to 02, 2010

TEST SAMPLE: ENGINEERING SAMPLE

STANDARD: AS/NZS 4268: 2008+A1:2010

The above equipment (Model: Y-R0016) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the

requirement of the above standards. The test record, data evaluation & Equipment Under

Test (EUT) configurations represented herein are true and accurate accounts of the

measurements of the sample’s EMC characteristics under the conditions specified in this

report.

PREPARED BY : , DATE: Sep. 08, 2010 ( Carol Liao, Specialist )

TECHNICAL ACCEPTANCE

:

, DATE: Sep. 08, 2010 ( Hank Chung, Deputy Manager )

APPROVED BY :

, DATE: Sep. 08, 2010 ( May Chen, Deputy Manager )


2. SUMMARY OF TEST RESULTS

APPLIED STANDARD: AS/NZS 4268: 2008+A1:2010 ( Row 45A)

Standard Subclause Test Type and Limit Result Remark

TRANSMITTER PARAMETERS

8.1 Equivalent isotropically radiated power (eirp) Pass Applicable

8.1 Equivalent isotropically conducted power (eirp) NA Not applicable

8.2 Measurement radiated spurious emission Pass Applicable

8.2 Measurement conducted spurious emission NA Not applicable

8.3 Emission bandwidth Pass Applicable 8.4 Operating frequency limits Pass Applicable

RECEIVER PARAMETERS

9.1 Measurement radiated spurious emission Pass Applicable

9.1 Measurement conducted spurious emission NA Not applicable

NOTE Additional Requirement Result Remark Power Spectral Density Pass Applicable 6dB bandwidth Pass Applicable

Outside In any 100kHz the frequency band Pass Applicable


2.1 TEST INSTRUMENTS

DESCRIPTION & MANUFACTURER

MODEL NO. SERIAL NO. CALIBRATED DATE

CALIBRATED UNTIL

Spectrum Analyzer FSP 40 100036 Dec. 18, 2009 Dec. 17, 2010 Mini-Circuits Pre_Amplifier ZFL-1000VH2 QA0838008 NA NA

HP Pre_Amplifier 8449B 3008A01923 Nov. 02, 2009 Nov. 01, 2010 Schaffer antenna 6112B 2731 NA NA EMCO Horn_Antenna 3115 6787 NA NA Schwarzbeck Horn_Antenna BBHA 9170 BBHA9170153 Jan. 22, 2010 Jan. 21, 2011

Software ADT_Radiated_V7.6.15.9.2 NA NA NA

CT Antenna Tower & Turn Table NA NA NA NA

Anritsu Power meter ML2495A 0824006 May 04, 2010 May 03, 2011 Anritsu Power sensor MA2411B 0738172 May 04, 2010 May 03, 2011 ESG Vector signal generator E4438C MY47271330

506 602 UNJ May 07, 2010 May 06, 2011

NOTE: 1. The test was performed in RF Chamber No. C. 2. The calibration interval of the above test instruments is 12 months and the calibrations

are traceable to NML/ROC and NIST/USA.

DESCRIPTION & MANUFACTURER

MODEL NO. SERIAL NO. CALIBRATED DATE

CALIBRATED UNTIL

Spectrum Analyzer FSP 40 100036 Dec. 18, 2009 Dec. 17, 2010

Spectrum Analyzer E4446A MY48250113 Dec. 02, 2009 Dec. 01, 2010

Anritsu Power meter ML2495A 0824006 May 04, 2010 May 03, 2011

Anritsu Power sensor MA2411B 0738172 May 04, 2010 May 03, 2011

Electronics AC Power

Source 6502 1140503 NA NA

OVEN MHU-225AU 911033 Dec. 17, 2009 Dec. 16, 2010

DC Power Supply GPC - 3030D 7700087 NA NA

ESG Vector signal generator

E4438C MY47271330 506 602 UNJ May 07, 2010 May 06, 2011

NOTE: 1. The test was performed in Oven room A. 2. The calibration interval of the above test instruments is 12 months and the calibrations

are traceable to NML/ROC and NIST/USA.


2.2 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT:

Parameter Uncertainty radio frequency ±1.132x10-6 Total RF power, conducted ±1.017dB RF power density, conducted ±1.017dB all emissions, radiated ±2.855dB Humidity ±2.5% Temperature ±0.7°C DC and low frequency voltages ±0.04%


3. GENERAL INFORMATION

3.1 GENERAL DESCRIPTION OF EUT

PRODUCT 2.4GHz Cordless keyboard

MODEL NO. Y-R0016 NOMINAL VOLTAGE DC 2.8V from rechargeable battery VOLTAGE OPERATING RANGE

Vnom= 2.8Vdc Vmin= 3.2Vdc Vmax= 2.3Vdc

MODULATION TYPE GFSK

OPERATING FREQUENCY 2405MHz ~ 2474MHz

IF&I.O. FREQUENCY NA

NUMBER OF CHANNEL 12

ANTENNA TYPE Custom inverted F PCB printed antenna, with 0.68dBi antenna gain

TEMPERATURE OPERATING RANGE -20℃ ~ 55℃

DATA CABLE NA

I/O PORT NA

ASSOCIATED DEVICES rechargeable battery x 1 NOTE:

1. The EUT must be supplied with a rechargeable battery as following table: BRAND Maxell MODEL ML2032 OUTPUT POWER 2.8V

2. The above EUT information was declared by manufacturer and for more detailed feature descriptions, please refer to the manufacturer's specifications or User's Manual.


3.2 DESCRIPTION OF TEST MODES

Twelve channels are provided to this EUT.

Channel Freq. (MHz) Channel Freq.

(MHz) Channel Freq. (MHz) Channel Freq.

(MHz) 1 2405 4 2417 7 2441 10 2465 2 2408 5 2432 8 2444 11 2471 3 2414 6 2435 9 2462 12 2474

3.2.1TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL

APPLICABLE TO EUT CONFIGURE

MODE EIRP OF EB BE SE<1G SE≥1G DESCRIPTION

- √ √ √ √ √ √

Where EIRP: Equivalent Isotropically Radiated Power (eirp) OF: Operating Frequencies Range

EB: Emission Bandwidth BE: Conducted Out-Band Emissions measurement SE<1G: Spurious Emissions below 1GHz SE≥1G: Spurious Emissions above 1GHz NOTE: “-“ means no effect

EQUIVALENT ISOTROPIC RADIATED POWER (EIRP):

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, packet types, XYZ axis and antenna ports (if EUT with antenna diversity architecture).

Following channel(s) was (were) selected for the final test as listed below.

AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE

1 to 12 1, 8, 12 GFSK

OPERATING FREQUENCIES RANGE:

Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, packet types and antenna ports (if EUT with antenna diversity architecture).



1 to 12 1, 12 GFSK


EMISSION BANDWIDTH:




1 to 12 1, 8, 12 GFSK

CONDUCTED OUT-BAND EMISSION MEASUREMENT:




1 to 12 1, 12 GFSK

SPURIOUS EMISSIONS TEST (BELOW 1 GHz):




1 to 12 1 GFSK

SPURIOUS EMISSIONS TEST (ABOVE 1 GHz):




1 to 12 1, 8, 12 GFSK


TEST CONDITION:

APPLICABLE TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY

EIRP 25deg. C, 60%RH, 1012 hPa

OF 25deg. C, 60%RH, 1012 hPa

EB 25deg. C, 60%RH, 1012 hPa

BE 25deg. C, 60%RH, 1012 hPa

DC 2.8V Wen Yu

SE<1G 25deg. C, 63%RH, 1012 hPa DC 2.8V Kent Liu

SE≥1G 25deg. C, 63%RH, 1012 hPa DC 2.8V Kent Liu

3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF Product, according to the specifications of the manufacturers, it must comply with the requirements of the following standards: AS/NZS 4268: 2008+A1:2010 EN 300 440-1 V1.4.1 (for method of measurement) All test items have been performed and recorded as per the above standards.


3.4 DESCRIPTION OF SUPPORT UNITS

The EUT has been tested as an independent unit.

3.1 CONFIGURATION OF SYSTEM UNDER TEST

TEST TABLE

EUT


4. TEST PROCEDURES AND RESULTS

TRANSMITTER PARAMETERS 4.1 RF OUTPUT POWER (EIRP) 4.1.1 LIMITS OF RF OUTPUT POWER AT THE HIGHEST POWER LEVEL

Frequency Range

(MHz) RF Output Power Limit

2400 to 2483.5 4W (36 dBm)

4.1.2 TEST PROCEDURES Refer ETSI EN 300 440-1 V1.4.1 clause 7.1. 4.1.3 DEVIATION FROM TEST STANDARD No deviation. 4.1.4 TEST SETUP

The test setup has been constructed as the normal use condition. The EUT was placed on the turn-table. Controlling software (Button Function) has been activated to set the EUT on specific status.


4.1.5 TEST RESULTS

TRANSMITTER POWER (dBm)

(CH1) 2405MHz

(CH8) 2444MHz

(CH12) 2474MHz

Test Condition

AV AV AV

Tnom(℃) 25 Vnom(v) 0.08 0.63 -1.40

Vmin(v) 0.68 1.53 -0.70 Tmin(℃) -20

Vmax(v) 0.65 1.51 -0.67

Vmin(v) -0.62 0.13 -1.90 Tmax(℃) 55

Vmax(v) -0.58 0.18 -1.93


4.2 MEASUREMENT RADIATED SPURIOUS EMISSION

4.2.1 LIMIT OF MEASUREMENT RADIATED SPURIOUS EMISSION

Frequency range Frequencies below 1GHz

Frequencies above 1GHz

Limit -18.24dBm -27.85dBm

4.2.2 TEST PROCEDURES

Refer ETSI EN 300 440-1 V1.4.1 clause 7.3.

4.2.3 TEST SETUP

For the actual test configuration, please refer to the related Item in this test report

(Photographs of the Test Configuration).

The EUT was placed on the table. Set the transmitter part of the EUT under transmitter

condition continuously at specific channel frequency.


4.2.4 TEST RESULTS

SPURIOUS EMISSION FREQUENCY RANGE 30MHz ~ 1GHz OPERATING

CHANNEL 1

SPURIOUS EMISSION LEVEL

Frequency

(MHz)

Antenna

Polarization

Level

(dBm)

Limit

(dBm) Margin

66.80 H -76.72 -18.24 -58.48

71.75 V -77.03 -18.24 -58.79

94.30 H -63.70 -18.24 -45.46

106.95 H -69.82 -18.24 -51.58

106.95 V -72.76 -18.24 -54.52

114.10 H -73.11 -18.24 -54.87

114.65 V -76.89 -18.24 -58.65

200.45 V -77.59 -18.24 -59.35

210.90 V -76.35 -18.24 -58.11

219.70 V -77.33 -18.24 -59.09

220.25 H -76.79 -18.24 -58.55

228.50 H -73.53 -18.24 -55.29

652.80 H -65.66 -18.24 -47.42

662.60 H -65.64 -18.24 -47.40

742.40 V -65.49 -18.24 -47.25

753.60 V -65.17 -18.24 -46.93

764.80 H -66.84 -18.24 -48.60

794.20 H -66.50 -18.24 -48.26

794.20 V -65.08 -18.24 -46.84

808.20 V -65.12 -18.24 -46.88

822.20 H -66.35 -18.24 -48.11

841.80 V -65.30 -18.24 -47.06

853.00 H -65.73 -18.24 -47.49

854.40 V -65.01 -18.24 -46.77 NOTE: The emission behavior belongs to narrowband spurious emission.


SPURIOUS EMISSION FREQUENCY RANGE 1GHz ~ 25GHz OPERATING

CHANNEL 1, 8 & 12


Channel Frequency (MHz)

Antenna Polarization

Level (dBm)

Limit (dBm)

Margin (dB)

4810.00 H -55.25 -27.85 -27.40

4810.00 V -54.77 -27.85 -26.92

7214.92 H -56.83 -27.85 -28.98

7215.00 V -55.62 -27.85 -27.77

9619.97 H -51.31 -27.85 -23.46

1

9620.01 V -52.19 -27.85 -24.34

4887.97 V -56.17 -27.85 -28.32

4888.10 H -56.62 -27.85 -28.77

7332.07 H -55.67 -27.85 -27.82

7332.11 V -53.47 -27.85 -25.62

9775.92 H -50.30 -27.85 -22.45

8

9776.04 V -50.16 -27.85 -22.31

4947.98 H -54.87 -27.85 -27.02

4948.11 V -56.03 -27.85 -28.18

7421.96 V -49.94 -27.85 -22.09

7422.05 H -53.01 -27.85 -25.16

9895.97 V -49.76 -27.85 -21.91

12

9896.06 H -50.92 -27.85 -23.07 NOTE: The emission behavior belongs to narrowband spurious emission.


4.3 OPERATING FREQUENCIES RANGE

4.3.1 LIMIT OF PERMITTED RANGE OF OPERATING FREQUENCIES

The width of the power envelope is fH –fL for a give operating frequency. In equipment

that allow adjustment or selection of different frequencies, the power envelope take up

different positions in the allowed band. The frequency range is determined by the

lowest value of fL and the highest value of fH resulting from the adjustment of the

equipment to the lowest and highest operating frequency.


Refer ETSI EN 300 440-1 V1.4.1 clause 7.2.2.

4.3.3 TEST SETUP

The EUT was placed in an environment where the temperature can be controlled. The

power source should be replaced by a power supply for voltage change. Set the

transmitter part of the EUT under transmission condition continuously at specific channel

frequency.


4.3.4 TEST RESULTS

Frequency (MHz) Test Condition

Lowest Highest

Tnom(℃) 25 Vnom(V) 2404.20 2474.86

Vmin(V) 2404.08 2474.98 Tmin(℃) -20

Vmax(V) 2404.06 2474.99

Vmin(V) 2404.33 2474.72 Tmax(℃) 55

Vmax(V) 2404.35 2474.70

Measured frequency (lowest and highest) FL= 2404.06 FH= 2474.99

Note: Power level at which the measurement has been performed: maximum output power


4.4 EMISSION BANDWIDTH

4.4.1 LIMIT OF EMISSION BANDWIDTH

NOTE: The upper and lower frequency limits of the emission bandwidth shall at all times remain within the operating frequency limits given in AS/NZS 4268 Clause 8.4.

4.4.2 TEST PROCEDURE

The bandwidth of the fundamental frequency was measured by spectrum analyzer with 100 kHz RBW and 100kHz VBW. The 99% power bandwidth was measured and recorded.

4.4.3 DEVIATION FROM TEST STANDARD

No deviation

4.4.4 TEST SETUP The test setup has been constructed as the normal use condition. The EUT was placed on

the turn-table. Controlling software (Button Function) has been activated to set the EUT on

specific status.


4.4.5 TEST RESULTS

CHANNEL CHANNEL FREQUENCY (MHz)

99% OCP BW (MHz)

1 2405 1.54 8 2444 1.60 12 2474 1.72

CH12


4.5 6dB BANDWIDTH MEASUREMENT

4.5.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT The minimum of 6dB Bandwidth Measurement is 0.5 MHz.

4.5.2 TEST PROCEDURE

The bandwidth of the fundamental frequency was measured by spectrum analyzer with 100 kHz RBW and 100 kHz VBW. The 6dB bandwidth is defined as the total spectrum the power of which is higher than peak power minus 6dB.


No deviation

4.5.4 TEST SETUP The test Setup has been constructed as the normal test conditions. In case of conducted

measurements the transmitter shall be connected to the measuring equipment. Controlling

software (Button Function) has been activated to set the EUT on specific status.


4.5.5 TEST RESULTS

CHANNEL CHANNEL

FREQUENCY (MHz)

6dB BANDWIDTH (MHz)

MINIMUM LIMIT (MHz)

PASS/FAIL

1 2405 0.67 0.5 PASS 8 2444 0.64 0.5 PASS 12 2474 0.59 0.5 PASS

CH1


4.6 POWER SPECTRAL DENSITY MEASUREMENT

4.6.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT The Maximum of Power Spectral Density Measurement is 25mW (14dBm).

4.6.2 TEST PROCEDURE The bandwidth of the fundamental frequency was measured with the spectrum analyzer using 3kHz RBW and 30kHz VBW. The power spectral density was measured and recorded. The sweep time is allowed to be longer than span/3kHz for a full response of the mixer in the spectrum analyzer.


No deviation





4.6.5 TEST RESULTS

CHANNEL NUMBER

CHANNEL FREQUENCY

(MHz )

RF POWER LEVEL IN 3kHz BW

(dBm)

MAXIMUM LIMIT (dBm)

PASS/FAIL

1 2405 -10.4 14 PASS

8 2444 -10.9 14 PASS

12 2474 -11.5 14 PASS

CH1


4.7 CONDUCTED - OUT BAND EMISSIONS MEASUREMENT

4.7.1 LIMITS OF CONDUCTED - OUT BAND EMISSIONS MEASUREMENT Below –20dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth).

4.7.2 TEST PROCEDURE Set both RBW and VBW of spectrum analyzer to 100kHz and 300kHz with suitable frequency span including 100MHz bandwidth from band edge. The band edges was measured and recorded.

4.7.3 DEVIATION FROM TEST STANDARD No deviation




4.7.5 TEST RESULTS The spectrum plots are attached on the following pages. D1 line indicates the highest level, D2 line indicates the 20dB offset below D1. It shows compliance with the requirement in AS/NZS 4268: 2008+A1:2010. (8.4).


4.7.5.1 TEST RESULTS CH 1


CH12


RECEIVER PARAMETERS

4.8 MEASUREMENT RADIATED SPURIOUS EMISSION

4.8.1 LIMIT OF MEASUREMENT RADIATED SPURIOUS EMISSION

Frequency range Frequencies below 1GHz Frequencies above 1GHz

Limit -54.81dBm -44.84dBm


Refer ETSI EN 300 440-1 V1.4.1 clause 8.3.

4.8.3 TEST SETUP The EUT is placed on the turn-table. Switch it to the channel being tested. Make sure the

receiver can receive the signal form transmitter.

For the actual test configuration, please refer to the related Item in this test report

(Photographs of the Test Configuration).

.


4.8.4 TEST RESULTS

SPURIOUS EMISSION FREQUENCY RANGE 30MHz ~ 1GHz OPERATING

CHANNEL 1


Frequency

(MHz)

Antenna

Polarization

Level

(dBm)

Limit

(dBm) Margin

25.00 H -68.71 -54.81 -13.90

28.85 V -60.22 -54.81 -5.41

34.35 V -67.67 -54.81 -12.86

37.65 V -69.91 -54.81 -15.10

76.15 H -67.24 -54.81 -12.43

90.45 V -73.45 -54.81 -18.64

95.40 H -63.43 -54.81 -8.62

99.80 H -67.49 -54.81 -12.68

106.95 V -73.50 -54.81 -18.69

114.65 H -71.96 -54.81 -17.15

229.05 H -72.23 -54.81 -17.42

300.00 V -74.92 -54.81 -20.11

650.00 H -72.87 -54.81 -18.06

736.80 V -71.76 -54.81 -16.95

753.60 V -71.25 -54.81 -16.44

888.00 H -71.86 -54.81 -17.05

888.00 V -71.21 -54.81 -16.40

900.60 V -70.94 -54.81 -16.13

909.00 H -71.52 -54.81 -16.71

913.20 V -71.90 -54.81 -17.09

914.60 H -71.57 -54.81 -16.76

934.20 H -72.40 -54.81 -17.59

991.60 H -72.54 -54.81 -17.73



SPURIOUS EMISSION FREQUENCY RANGE 1GHz ~ 25GHz OPERATING

CHANNEL 1, 8 & 12


Channel Frequency (MHz)

Antenna Polarization

Level (dBm)

Limit (dBm)

Margin (dB)

2750.76 V -62.75 -44.84 -17.91

2750.93 H -57.37 -44.84 -12.53

5499.36 V -64.50 -44.84 -19.66 1

5501.73 H -61.92 -44.84 -17.08

2795.49 H -57.94 -44.84 -13.10

2795.56 V -62.56 -44.84 -17.72

5590.30 V -64.50 -44.84 -19.66 8

5590.85 H -62.82 -44.84 -17.98

2829.54 V -61.03 -44.84 -16.19

2829.69 H -56.40 -44.84 -11.56

5659.31 H -63.25 -44.84 -18.41 12



5. PHOTOGRAPHS OF THE TEST CONFIGURATION

Tx and Rx SPURIOUS EMISSION TEST


RF OUTPUT POWER TEST


6. INFORMATION ON THE TESTING LABORATORIES

We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025:

Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following:

Linko EMC/RF Lab: Tel: 886-2-26052180 Fax: 886-2-26052943

Hsin Chu EMC/RF Lab: Tel: 886-3-5935343 Fax: 886-3-5935342

Hwa Ya EMC/RF/Safety/Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050

Email: [email protected] Web Site: www.adt.com.tw

The address and road map of all our labs can be found in our web site also.

--- END ---

CONSTRUCTION PHOTOS OF EUT

RADIO TEST REPORT (AS/NZS 4268) - Logitech No.: RC990901E04 1 Report Format Version 3.0.1 RADIO TEST...

Documents

Transcript of RADIO TEST REPORT (AS/NZS 4268) - Logitech No.: RC990901E04 1 Report Format Version 3.0.1 RADIO TEST...