FlorestoneTub / ShowerFeatures

2851 Falcon Drive • Madera, CA 93637

T. 559.661.4171 • T. 800.446.8827

F. 559.661.2070 • florestone.com

FACTORY INSTALLED OPTIONALHYDROMASSAGE SYSTEMS.Florestone Tub/Showers are available with full-therapy jet action hydromassage systems, creating a complete body-surround therapy massage action, soothing away body aches and tension. Fitting are available in matching PVC colors, chrome or polished brass finishes.

OPTIONAL GRAB BARS.In most applications Florestone Products can mount additional grab bars to its line of tub/showers. Drawings are required.

COLORSStandard: White

OPTIONAL MANUFACTURERS' MATCH COLORS

AMERICAN STANDARD

ELJER

KOHLER

For other colors, call for availability and price.

QUALITY YOU CAN TRUST.

Since 1947, Florestone Products Company has built a reputation based on product quality, ease of installation and reliability. Today we serve contractors, engineers, specifiers, architects and builders with products, service and distribution nationwide. The manufacturing methods, craftsmanship and attention to detail of Florestone Fiberglass Showers are second to none.

WIDE VARIETY OF SIZESAND STYLES.

We offer a wide choice of models, sizes, and styles. The "tile back" look gives you another decorative option.

Bone

Candlelight

Daydream

Fawn Beige

Light Mink

Loganberry

Rain Forest

Rhapsody Blue

Spring

Sterling Silver

Shell

Warm White

Classic Grey

Dusty Rose

Glacier Blue

Island Sea

Natural

Peach Bisque

Platinum

Ruby

Sage

Sandlewood

Twilight Blue

Verde

Zinfandel

Almond

Biscuit

Chamois

Country Grey

Desert Bloom

Ice Grey

Innocent Blush

Jersey Cream

Mexican Sand

Merlot

Seafoam Green

Skylight

Teal Tender Grey

Thunder Grey

Timberline

Wild Rose

Tu

b / S

how

ers

Insta

llatio

n In

stru

ctio

ns

8

FLORESTONE TUB / SHOWERSSHOULD BEINSTALLED BY A PROFESSIONAL PLUMBINGCONTRACTOR.

Complete two sides of the squared and framed pocket according to dimensional drawings

Some Florestone units are too large to pass through doorways. Make sure the unit is in the installation area before framing is completed.

*Note on Code Compliance:

Since local codes and regulations vary, Florestone Products will not be responsible for code compliance. Please check with your local city and county building departments for specific regulations or restrictions before ordering.

FlorestoneTub / ShowersInstallation Instructions

Dimensions may vary ± ¼" inch-

check unit before installation.

FRAMING

SETTING SHOWER / BATH UNITInstall unit into position with front apron firmly on the floor. Use a level (3¥ min.) on the offset of front and side faces. Level top ledge of dam. Plumb and leveló shim if necessary. Mortar or plaster base is recommended.

SECURE UNITFasten back and sidewall flanges to studs with large-headed #6 galvanized nails. Use #12 sheet metal screws for installation into steel studs.

ROUGH PLUMBINGRough plumbing must extend above sub-floor or slab 1". Lay out accurate location of valves and, working from unfinished side of unit, drill º" holes. From finished side of unit enlarge holes with a hole saw. For large openings use a saber saw. Because the one-piece construction eliminates the possibility of reaching over the tub end to connect the drain and overflow, unit should be located to provide access through the walls to make connections. Check for leaks before installing drywall and closing off plumbing access. With fire rated walls, finished wall board must be in place before units are installed.

CAULK Caulk all openings around valves and outlets with a silicone caulking.

CLEANING Clean up with liquid detergent and warm water.

AVOID USING ABRASIVE CLEANERS. They may scratch and dull the surface of the unit.