QSF 75-100 ( Manual de Compresores )

QSF™ 75/100 Direct Drive Rotary Screw Air Compressor

Parts Manual

This manual contains important safety information and should be made available to all personnel who operate and/or maintain this product. Carefully read this manual before attempting to operate or perform maintenance on this equipment.

Manual No. 65018-CA

April 2001 Edition

Alphabetical Index

Quincy Compressor® - QSF™ 75 & 100 HP

Airend Groups (revised) .................................................................................................................. 4-7Air Filter Groups:

(75 HP) ............................................................................................................................... 66-67(100 HP) ............................................................................................................................. 68-69

Air Piping Groups: (revised)(air-cooled) ......................................................................................................................... 50-51(water-cooled) .................................................................................................................... 52-53

Base/Coupling Groups: (revised)(75 HP) ............................................................................................................................... 10-11(100 HP) ............................................................................................................................. 12-13

Cabinet Groups:(air-cooled) ......................................................................................................................... 70-71(water-cooled) .................................................................................................................... 72-73

Control Piping Groups: (revised)(75 HP, less differential pressure switches) ........................................................................ 24-25(75 HP, with differential pressure switches) ........................................................................ 26-29(100 HP, across the line, less differential pressure switches) ............................................. 30-31(100 HP, across the line, with differential pressure switches) ............................................. 32-35(100 HP, wye-delta) ............................................................................................................ 36-39

Control Schematics ..................................................................................................................... 76-80Cooler Groups (air-cooled) .......................................................................................................... 54-55Decal Groups .............................................................................................................................. 74-75Discharge Piping Groups ................................................................................................................... 9Electrical Groups:

Electrical Control Diagrams .................................................................................................... 81-83Starting Groups: (revised)

(across the line) .................................................................................................................. 14-19(wye-delta) ......................................................................................................................... 20-23

Fluid Piping Groups:(air-cooled) ......................................................................................................................... 56-57(water-cooled) .................................................................................................................... 58-61

Fluid Sample Group (optional) ........................................................................................................... 3Fluid Specifications (revised) ............................................................................................................. 2Gauge Groups (percent capacity)(optional) ................................................................................ 40-41Inlet Valve Groups:

(75 HP) ............................................................................................................................... 44-45(100 HP, across the line) .................................................................................................... 46-47(100 HP, wye-delta) ............................................................................................................ 48-49

Maintenance Kits (revised) .......................................................................................................... 84-86Recommended Spare Parts ............................................................................................................. 86Reservoir Groups ........................................................................................................................ 42-43Serial Number Identification ............................................................................................................... 1Shaft Seal Kit ..................................................................................................................................... 8Water Piping Groups:

(fresh water) ....................................................................................................................... 62-63(sea water) ......................................................................................................................... 64-65

Quincy Compressor® - QSF™ 75 & 100 HP 1

SERIAL NUMBER IDENTIFICATION

The serial number tag is located on the top flange of the unit frame just left of the controlpanel and in the upper right corner of the electrical control panel.

ORDERING REPLACEMENT PARTS

Prompt service can be rendered on replacement part orders if the following information isgiven:

1. The serial number must be given when ordering replacement parts.

2. State the exact part number needed. Do not order by index numbers, asindex numbers are repeated throughout this manual and if used for orderingparts will necessitate time consuming correspondence.

3. State the exact quantity needed.

4. State the preferred type of transportation.

All replacement parts are to be ordered through an authorized distributor. Insist onGenuine Quincy Parts only! Failure to do so may void your warranty.

WARNING Guards must be fastened in place beforestarting the machine and never removedbefore disconnecting and locking out themain power supply.

DANGER Air in the piping from this equipment willcause severe injury or death if used forbreathing air or food processing (If non-foodgrade fluid is used). Air used for these pro-cesses must meet OSHA 29CFR1910.134 orFDA 21CFR178.3570 standards.

2 Quincy Compressor® - QSF™ 75 & 100 HP

FLUID SPECIFICATIONS

We recommend that all Quincy Rotary Screw Compressors be filled with one of the followingfluids:

QuinSyn Synthetic FluidsQuinSyn PG™ QuinSyn-F® (food grade)QuinSyn Plus™ QuinSyn IVQuinSyn® QuinSyn XP®

Synthetic fluids other than QuinSyn brand may not be compatible with components used in aQuincy compressor. If it is deemed necessary to convert a Quincy Compressor to a syntheticother than QuinSyn brand, please contact an authorized Quincy Compressor distributor. Tolocate your nearest distributor, contact Sales & Marketing in Quincy, Illinois:Phone 217-222-7700, FAX 217-222-4138 or visit our website: http://www.quincycompressor.com.

The following information will be required by the distributor:

MODEL QSF: (circle configuration) _______________________________________________________________

SERIAL NO. ____________________________________________________________

FLUID ORIGINALLY USED: ________________________________________________

FLUID NOW USED (IF CHANGED): _________________________________________

FLUID TO BE USED: _____________________________________________________

• Additional Information

Additional information can be found in the QSF Instruction Manual.

• Fluid Analysis Kit

Quincy Compressor offers free fluid analysis to provide early detection of excessive parts wear,fluid breakdown, or a contaminated fluid system. Order the Fluid Analysis Kit (part no. 128515)from your local authorized Quincy Compressor distributor.

• Fluid Requirements

QSF AIR-COOLED QSF WATER-COOLED75 HP 10.5 gallons 75 HP 10.5 gallons100 HP 10.5 gallons 100 HP 10.5 gallons

All Quincy Compressors are filled at the factory with QuinSyn PG unless otherwise specified.

A/C W/C 75 HP 100 HP 100 psi 125 psi 150 psi


FLUID SAMPLE GROUP143394-002

1 6.0 FT 140620-003 TUBING-NYLON, BLACK, 1/4 O.D. 2 1 124349-005 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.25 NPT 3 1 142722-1 BRACKET-LINE FILTER, MANUAL 4 1 129203-003 COUPLING-BULKHEAD 5 1 142947 VALVE-ANGLE, NEEDLE 6 2 110511-K10 SCREW-TAP, ZINC, 5/16-18 UNC X 0.75 7 1 128967-001 FITTING-ELBOW, 45° MALE, 0.25 TUBE X 0.12 NPT 8 1 140106-024 FITTING-ADAPTER, 7/16-20 X 1/4-4 NPTF, SAE O-RING 9 1 121033-1 BUSHING-PIPE, BRASS, 0.25 NPT X 0.12 NPT

* This group used only on units less differential pressure switches (reference Control Piping Groups).

ITEM PARTNUMBER QTY. NUMBER DESCRIPTION


AIREND GROUPS

NOTES-UNLESS OTHERWISE SPECIFIED:1) ITEM 30 LOCATED ON THE BACK OF THE INLET HOUSING (UNDER THE

ROTOR HOUSING).2) ONLY REPAIRABLE OR REPLACEABLE ITEMS ARE SHOWN (INTERNAL

AIREND COMPONENTS NOT SHOWN).3) NOT ALL REPLACEABLE ITEMS SHOWN.

NOTE 1


AIREND GROUPS


1 1 129619 SLINGER 2 1 143931 ADAPTER-SEAL 3 1 129964-002 RING-RETAINER, BEARING 4 1 22749-252 O-RING, VITON 5 1 142587 SEAL-SHAFT 6 1 129620 SEAL-WEAR RING 7 * CASING-INLET 8 14 128883-044 PLUG-PIPE, 7/16-20, SAE O-RING 9 4 124145-005 PIN-DOWEL 10 1 143930 ADAPTER-MOTOR 11 * HOUSING-ROTOR 12 1 124232-005 BEARING-ROTOR, SUCTION END 13 1 128203-393 RING-RETAINER 14 * ROTOR-MALE 15 * ROTOR-FEMALE 16 1 22749-385 O-RING, VITON 17 26 90386-N17 SCREW-COUNTERBORE, 1/2-13 UNC X 2.00,

GRADE 8 (@ 75 FT-LBS) 18 1 22530 GASKET-PLATE, FLUID GALLERY 19 1 22528 PLATE-COVER, FLUID GALLERY 20 10 90386-L12 SCREW-COUNTERBORE, 3/8-16 UNC X 1.00,

GRADE 8 (@ 35 FT-LBS) 21 ** SHIM-ROTOR, TEMPERED STEEL 22 1 128883-162 PLUG-PIPE, 1-5/8-12, SAE O-RING 23 1 BEARING-ROTOR, DISCHARGE END 24 2 BEARING-ROTOR, DISCHARGE END 25 1 BEARING-ROTOR, DISCHARGE END 26 2 126701 RETAINER-BEARING 27 7 90386-L14 SCREW-COUNTERBORE, 3/8-16 UNC X 1.25,

GRADE 8 (@ 45 FT-LBS, BACK OFF TO 25 FT-LBS) 28 2 22749-243 O-RING, VITON 29 ** SHIM-ROTOR, TEMPERED STEEL 30 2 128883-056 PLUG-PIPE, 9/16-18, SAE O-RING

Items 31-51 and the component maintenance parts are on page 7.

* Items not sold separately, must be ordered as a complete airend.** Quantity as required.@ Indicates torque value in foot pounds (lubricated threads).


AIREND GROUPS

NOTES-UNLESS OTHERWISE SPECIFIED:1) ITEM 30 LOCATED ON THE BACK OF THE INLET HOUSING (UNDER THE

ROTOR HOUSING).2) ONLY REPAIRABLE OR REPLACEABLE ITEMS ARE SHOWN (INTERNAL

AIREND COMPONENTS NOT SHOWN).3) NOT ALL REPLACEABLE ITEMS SHOWN.

NOTE 1


31 1 129463 CAP-DISCHARGE 32 8 90386-N15 SCREW-COUNTERBORE, 1/2-13 UNC X 1.50,

GRADE 8 (@ 75 FT-LBS) 33 1 110705-D04 PIN-ROLL, 1/8 X 0.38 34 1 128883-106 PLUG-PIPE, 1-1/16-12, SAE O-RING 35 1 129665 CAP-DISCHARGE 36 1 142318 SHAFT-INPUT 37 1 142194 CAP-SPRAY NOZZLE 38 1 22749-281 O-RING, VITON 39 1 143165-J10 SCREW-PATCH, 12 PT, 0.25 UNC X 0.75 40 1 140537 STUD-FLUID FILTER 41 ** SHIM-ROTOR, TEMPERED STEEL 42 * BEARING-ROTOR, DISCHARGE END 43 * BEARING-ROTOR, SUCTION END 44 1 123478-N16 SCREW-CAP, 1/2-13 UNC X 1.75, GRADE 5 (@ 55 FT-LBS) 45 1 140317 GROMMET-RUBBER 46 * BEARING-ROTOR, DISCHARGE END 47 2 23207 ORIFICE-PLUG, 0.12 NPT 48 3 128883-075 PLUG-PIPE, 3/4-16, SAE O-RING 49 1 124393-004 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.12 NPT 50 * GEARS-MATCHED SET 51 2 2755S PLUG-PIPE, 1/8 NPT (75 HP only, located in fluid gallery plate)

COMPONENT MAINTENANCE PARTS

A 14 140406-904 O-RING, VITON B 1 140406-920 O-RING, VITON C 2 140406-906 O-RING, VITON D 1 140406-912 O-RING, VITON E 3 140406-908 O-RING, VITON

* Items not sold separately, must be ordered as a complete airend.** Quantity as required.@ Indicates torque value in foot pounds (lubricated threads).

AIREND GROUPS



SHAFT SEAL KIT143084

1 1 129619 SLINGER 2 1 142587 SEAL-SHAFT 3 1 129620 SEAL-WEAR RING

Reference QSF Instruction Manual to install compressor shaft seal. Tool Kit 140414 for QSF shaft seal and wear ringinstallation can be purchased from Quincy Compressor.


engb80

Note

Corrected tool kit part number.


142926-001 142926-002(<150 PSI) (150 PSI)

1 1 142321 ! MANIFOLD-DISCHARGE 2 1 140509S250 140394-025 COUPLING 3 1 22749-333 ! O-RING, VITON 4 4 123115-08C ! LOCKWASHER, 1/2 5 4 123478-N15 ! SCREW-CAP, 1/2-13 UNC X 1.50,

GRADE 5 (@ 55 FT-LBS) 6 2 124450G002 N/A CLAMP-PIPE, GALVANIZED, 2.50 7 4 123478-N17 N/A SCREW-CAP, 1/2-13 UNC X 2.00,

GRADE 5 (@ 55 FT-LBS) 8 4 124370-N02 N/A LOCKNUT, 1/2-13 UNC 9 2 124451-002 N/A BAR-TENSION


A 2 140509G250 140394-F25 GASKET-COUPLING

@ Indicates torque value in foot pounds (lubricated threads).

DISCHARGE PIPING GROUPS

ITEM PART PARTNUMBER QTY. NUMBER NUMBER DESCRIPTION


BASE/COUPLING GROUP142924-001 (75 HP)



1 1 142279 BASE 2 2 122680-18 WASHER-FLAT, 0.53 3 4 123478-Q17 SCREW-CAP, 5/8-11 UNC X 2.00, GRADE 5 (@ 110 FT-LBS) 4 2 142546 BRACKET-MOTOR SUPPORT 5 2 129059-3 SPACER-MOTOR 6 4 142201-03 MOUNT-MOTOR 7 6 110428W062 WASHER-FLAT, 5/8 8 14 123115-10C LOCKWASHER, 5/8 9 2 123478-N25 SCREW-CAP, 1/2-13 UNC X 4.00, GRADE 5 (@ 75 FT-LBS) 10 2 124370-N02 LOCKNUT, 1/2-13 UNC 11 2 123478-Q25 SCREW-CAP, 5/8-11 UNC X 4.00, GRADE 5 (@110 FT-LBS) 12 1 128387-145 COUPLING-DRIVE 13 1 160075-004 KEY-SQUARE 14 1 142589 GUARD-COUPLING 15 1 129673 GUARD-COUPLING 16 6 110511-K10 SCREW-TAP, ZINC, 5/16-18 UNC X 0.75 17 1 122680-20 WASHER-FLAT, 0.66 18 1 110428W075 WASHER-FLAT, 3/4 19 8 123478-Q16 SCREW-CAP, 5/8-11 UNC X 1.75, GRADE 5 (@ 110 FT-LBS)


A 1 128387-406 ELEMENT-DRIVE COUPLING(1 pair of halves sold as a matched set only)

B 1 128387-213 HUB-COUPLING, MOTOR SIDE (includes set screw) C 1 128387-320 HUB-COUPLING, AIREND SIDE (includes set screw) D 1 128387-502 BOLT KIT-DRIVE COUPLING (@ 30 FT-LBS)






1 1 142279 BASE 2 4 142201-04 MOUNT-MOTOR 3 2 142547 BRACKET-MOTOR SUPPORT 4 2 123478-Q20 SCREW-CAP, 5/8-11 UNC X 2.75, GRADE 5 (@ 110 FT-LBS) 5 1 122680-20 WASHER-FLAT, 0.66 6 5 110428W075 WASHER-FLAT, 3/4 7 10 123115-10C LOCKWASHER, 5/8 8 2 123478-N25 SCREW-CAP, 1/2-13 UNC X 4.00, GRADE 5 (@ 75 FT-LBS) 9 2 122680-18 WASHER-FLAT, 0.53 10 2 124370-N02 LOCKNUT, 1/2-13 UNC 11 4 123478-R19 SCREW-CAP, 3/4-10 UNC X 2.50, GRADE 5 (@ 200 FT-LBS) 12 4 123115-12C LOCKWASHER, 3/4 13 1 128387-143 COUPLING-DRIVE 14 1 160075-004 KEY-SQUARE 15 1 142589 GUARD-COUPLING 16 1 129673 GUARD-COUPLING 17 6 110511-K10 SCREW-TAP, ZINC, 5/16-18 UNC X 0.75 18 2 110428W062 WASHER-FLAT, 5/8 19 8 123478-Q16 SCREW-CAP, 5/8-11 UNC X 1.75, GRADE 5 (@ 110 FT-LBS)


A 1 128387-406 ELEMENT-DRIVE COUPLING(1 pair of halves sold as a matched set only)

B 1 128387-207 HUB-COUPLING, MOTOR SIDE (includes set screw) C 1 128387-320 HUB-COUPLING, AIREND SIDE (includes set screw) D 1 128387-502 BOLT KIT-DRIVE COUPLING (@ 30 FT-LBS)



STARTING GROUP (across the line)

PIX5085

NOTES-UNLESS OTHERWISE SPECIFIED:1) ITEM A (ENCLOSURE LATCH) IS NOT SHOWN.2) ITEMS 35 AND 36 (HEATER ELEMENTS) ARE NOT SHOWN.3) ITEM 37 (CURRENT TRANSFORMER) NOT SHOWN AND USED

ONLY WITH 143780-01 DRIVE MOTOR OVERLOAD RELAY.




1 1 129863-01 BUTTON-STOP 2 1 142081 DECAL-ELECTRONIC CONTROLLER 3 1 142131 CONTROLLER-ELECTRONIC 4 6 160048-F09 SCREW-SET, #8-32 UNC 5 6 124365-F02 NUT-#8-32 UNC 6 1 142659-03 PLUG-HEADER, 9 PIN 7 1 142659-04 PLUG-HEADER, 10 PIN 8 1 142659-01 PLUG-HEADER, 2 PIN 9 1 142659-02 PLUG-HEADER, 6 PIN10 1 129864-02 BLOCK-CONTACT, NORMALLY CLOSED11 2 122880-222 SWITCH-TEMPERATURE12 1 143754 PROBE-TEMPERATURE, HIGH VIBRATION13 1 142096-04 FITTING-STRAIN RELIEF14 1 142388 INSERT-MOUNTING, CABLE TIE15 1 143674 TRANSFORMER-24 VOLT16 1 142334-05 ASSEMBLY-TERMINAL BLOCK17 1 143470 SHEET-ELECTRICAL DECALS18 * (page 16) PHASE MONITOR (optional)19 * (page 16) FUSES-FAN MOTOR20 1 126263-004 FUSE BLOCK21 1 142133 TRANSDUCER-PRESSURE22 4 129203-003 COUPLING-BULKHEAD, BRASS23 4 123157-117 O-RING24 * (page 16) TRANSFORMER25 * (page 16) FUSES-TRANSFORMER26 * (page 17) CONTACTOR-DRIVE MOTOR27 * (page 17) RELAY-OVERLOAD, DRIVE MOTOR28 * (page 17) CONTACTOR-FAN MOTOR29 * (page 18) RELAY-OVERLOAD, FAN MOTOR30 1 143046-008 BUSHING-PIPE, 0.25 NPT X 1/8 NPT31 1 129596-001 SWITCH-DIFFERENTIAL PRESSURE, 10 PSI (optional)32 1 129596-002 SWITCH-DIFFERENTIAL PRESSURE, 19 PSI (optional)33 2 142125-2 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 1.2534 1 129597-001 SWITCH-VACUUM (optional)35 * (page 19) HEATER ELEMENT-FAN MOTOR36 * (page 19) HEATER ELEMENT-DRIVE MOTOR37 3 143781-300** TRANSFORMER-CURRENT


A 1 141784-001 LATCH-ENCLOSURE, NEMA 12 141784-002 LATCH-ENCLOSURE, NEMA 4

* Quantities and part numbers are listed in tabulations on the pages indicated.** Item 37 (current transformer) used only on 200 & 230 volt units (with 143780-01 drive motor overload relay).


ITEM 18 PHASE MONITOR (OPTIONAL)

QTY200V 1 129200-001230V 1 129200-001380V 1 129200-003415V 1 129200-003460V 1 129200-002575V 1 128422-003

ITEM 19 FAN MOTOR FUSES

AIR-COOLED AIR-COOLED, 100 HP WATER-COOLED75 HP (L/CABINET) (W/CABINET) 75 HP & 100 HP

QTY200V 3 128857-035 128857-035 128857-035 128857-007230V 3 128857-025 128857-025 128857-025 128857-007380V 3 128857-025 128857-021 128857-027 128857-032415V 3 128857-025 128857-021 128857-026 128857-005460V 3 128857-020 128857-020 128857-020 128857-012575V 3 128857-009 128857-009 128857-009 128857-030

ITEM 24 TRANSFORMER

QTY200V 1 128413-351230V 1 128413-353380V 1 128413-356415V 1 128413-354460V 1 128413-353575V 1 128413-355

ITEM 25 TRANSFORMER FUSES

QTY PRIMARY QTY SECONDARY200V 1 128857-006 1 128622-400230V 1 128857-005 1 128622-400380V 2 128857-004 1 128622-400415V 2 128857-004 1 128622-400460V 2 128857-014 1 128622-400575V 2 128857-011 1 128622-400



ITEM 26 DRIVE MOTOR CONTACTOR

75 HP 100 HPQTY

200V 1 141590-15 N/A230V 1 141590-14 141590-15380V 1 141590-12 141590-13415V 1 141590-11 141590-13460V 1 141590-11 141590-12575V 1 141590-10 141590-12

ITEM 27 DRIVE MOTOR OVERLOAD RELAY

STANDARD EFFICIENCY PREMIUM EFFICIENCY75 HP 100 HP 75 HP 100 HP

QTY200V 1 143780-01 N/A 141592-007 N/A230V 1 143780-01 143780-01 141592-006 141592-007380V 1 141591-073 141591-082 141592-005 141592-006415V 1 141591-068 141591-082 141592-005 141592-006460V 1 141591-067 141591-074 141592-005 141592-005575V 1 141591-063 141591-072 141592-004 141592-005

ITEM 28 FAN MOTOR CONTACTOR

75 HP (all),100 HP, W/C &100 HP, A/C, 100 HP, A/C,L/CABINET W/CABINET

QTY200V 1 141590-02 141590-02230V 1 141590-02 141590-02380V 1 141590-02 141590-03415V 1 141590-02 141590-03460V 1 141590-02 141590-02575V 1 141590-02 141590-02



ITEM 29 FAN MOTOR OVERLOAD RELAY

STANDARD EFFICIENCY

AIR-COOLED AIR-COOLED, 100 HP WATER-COOLED75 HP (L/CABINET) (W/CABINET) 75 HP & 100 HP

QTY200V 1 141591-014 141591-014 141591-014 141591-007230V 1 141591-013 141591-013 141591-013 141591-007380V 1 141591-014 141591-011 141591-030 141591-004415V 1 141591-013 141591-011 141591-030 141591-004460V 1 141591-010 141591-010 141591-010 141591-004575V 1 141591-009 141591-009 141591-009 141591-003

PREMIUM EFFICIENCY

AIR-COOLED75 HP & 100 HP

QTY200V 1 141592-001230V 1 141592-001380V 1 141592-001415V 1 141592-001460V 1 141592-001575V 1 141592-001

Standard efficiency overloads are Class 10.Premium efficiency overloads are Class 20.



ITEM 35 FAN MOTOR HEATER ELEMENT

AIR-COOLED AIR-COOLED, 100 HP75 HP (L/CABINET) (W/CABINET)

QTY200V 3 141607-040 141607-040 141607-040230V 3 141607-038 141607-038 141607-038380V 3 141607-038 141607-033 141607-042415V 3 141607-037 141607-032 141607-041460V 3 141607-031 141607-031 141607-031575V 3 141607-029 141607-029 141607-029

Heater elements used only with premium efficiency overloads.

ITEM 36 DRIVE MOTOR HEATER ELEMENT

75 HP 100 HPQTY

200V 3 141607-085 N/A230V 3 141607-084 141607-087380V 3 141607-075 141607-081415V 3 141607-074 141607-081460V 3 141607-073 141607-075575V 3 141607-070 141607-073




STARTING GROUP (wye-delta)

PIX5051

NOTES-UNLESS OTHERWISE SPECIFIED:1) ITEM A (ENCLOSURE LATCH) IS NOT SHOWN.2) ITEMS 35 AND 36 (HEATER ELEMENTS) ARE NOT SHOWN.




1 1 129863-01 BUTTON-STOP 2 1 142081 DECAL-ELECTRONIC CONTROLLER 3 1 142131 CONTROLLER-ELECTRONIC 4 6 160048-F09 SCREW-SET, #8-32 UNC 5 6 124365-F02 NUT-#8-32 UNC 6 1 142659-03 PLUG-HEADER, 9 PIN 7 1 142659-04 PLUG-HEADER, 10 PIN 8 1 142659-01 PLUG-HEADER, 2 PIN 9 1 142659-02 PLUG-HEADER, 6 PIN10 1 129864-02 BLOCK-CONTACT, NORMALLY CLOSED11 2 122880-222 SWITCH-TEMPERATURE12 1 143754 PROBE-TEMPERATURE, HIGH VIBRATION13 1 142096-04 FITTING-STRAIN RELIEF14 1 142388 INSERT-MOUNTING, CABLE TIE15 1 143674 TRANSFORMER-24 VOLT16 1 142334-05 ASSEMBLY-TERMINAL BLOCK17 1 143470 SHEET-ELECTRICAL DECALS18 * (page 16) PHASE MONITOR (optional)19 * (page 16) FUSES-FAN MOTOR20 1 126263-004 FUSE BLOCK21 1 142133 TRANSDUCER-PRESSURE22 4 129203-003 COUPLING-BULKHEAD, BRASS23 4 123157-117 O-RING24 * (page 16) TRANSFORMER25 * (page 16) FUSES-TRANSFORMER26 * (page 22) CONTACTOR-DRIVE MOTOR27 * (page 22) RELAY-OVERLOAD, DRIVE MOTOR28 * (page 17) CONTACTOR-FAN MOTOR29 * (page 18) RELAY-OVERLOAD, FAN MOTOR30 1 143046-008 BUSHING-PIPE, 0.25 NPT X 1/8 NPT31 1 129596-001 SWITCH-DIFFERENTIAL PRESSURE, 10 PSI32 1 129596-002 SWITCH-DIFFERENTIAL PRESSURE, 19 PSI33 2 142125-2 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 1.2534 1 129597-001 SWITCH-VACUUM35 * (page 19) HEATER ELEMENT-FAN MOTOR36 * (page 23) HEATER ELEMENT-DRIVE MOTOR37 1 141594-01 INTERLOCK-MECHANICAL38 * (page 23) CONTACTOR-SHORTING,DRIVE MOTOR


A 1 141784-001 LATCH-ENCLOSURE, NEMA 12 141784-002 LATCH-ENCLOSURE, NEMA 4

* Quantities and part numbers are listed in tabulations on the pages indicated.


ITEM 26 DRIVE MOTOR CONTACTOR

75 HP 100 HPQTY

200V 2 141590-12 N/A230V 2 141590-12 141590-13380V 2 141590-08 141590-12415V 2 141590-08 141590-11460V 2 141590-08 14159011575V 2 141590-08 141590-08

ITEM 27 DRIVE MOTOR OVERLOAD RELAY

STANDARD EFFICIENCY PREMIUM EFFICIENCY75 HP 100 HP 75 HP 100 HP

QTY200V 1 141591-074 N/A 141592-005 N/A230V 1 141591-073 141591-081 141592-005 141592-006380V 1 141591-061 141591-071 141592-004 141592-005415V 1 141591-060 141591-066 141592-004 141592-005460V 1 141591-060 141591-065 141592-004 141592-005575V 1 141591-059 141591-061 141592-004 141592-004

Standard efficiency overloads are Class 10.Premium efficiency overloads are Class 20.



ITEM 36 DRIVE MOTOR HEATER ELEMENT

75 HP 100 HPQTY

200V 3 141607-076 N/A230V 3 141607-074 141607-080380V 3 141607-067 141607-070415V 3 141607-066 141607-069460V 3 141607-066 141607-069575V 3 141607-064 141607-066


ITEM 38 DRIVE MOTOR SHORTING CONTACTOR

75 HP 100 HPQTY

200V 1 141590-11 N/A230V 1 141590-09 141590-12380V 1 141590-07 141590-08415V 1 141590-07 141590-08460V 1 141590-07 141590-07575V 1 141590-07 141590-07



CONTROL PIPING GROUP (75 HP)(less differential pressure switches)143383-11


CONTROL PIPING GROUP (75 HP)(less differential pressure switches)


1 1 128826-1 VALVE-BLOWDOWN 2 1 129732 FILTER-LINE, AUTOMATIC 3 1 21969-2 VALVE-DIFFERENTIAL PILOT 4 1 120496-5 VALVE-SOLENOID, 3-WAY

1 120496-4 VALVE-SOLENOID, 3-WAY (high pressure option) 5 33.0 FT 124435-003 TUBING-NYLON, 1/4 O.D. 6 1 121033-2 BUSHING-PIPE, BRASS, 0.38 NPT X 0.25 NPT 7 5 142125-1 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X CLOSE 8 6 124349-005 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.25 NPT 9 5 124349-004 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.12 NPT 10 2 90084 VALVE-SHUTTLE, 1/8 NPT 11 2 121034-2 TEE-PIPE, BRASS, 0.25 NPT 12 1 124349-010 FITTING-ELBOW, 90° MALE, 0.38 TUBE X 0.25 NPT 13 2 111098-002 NIPPLE-PIPE, BRASS, 0.12 NPT X 0.25 NPT X CLOSE 14 1 22455 CONNECTOR-ELECTRICAL, 1/2 15 1 8052 LOCKNUT-CONDUIT, 1/2 16 1 129203-003 COUPLING-BULKHEAD 17 1 6150 CROSS-PIPE, BRASS, 0.25 NPT 18 7.0 FT 140333 TUBE-STAINLESS STEEL, 0.25 O.D. 19 1 128886-003 FITTING-ELBOW, 0.25 TUBE X 7/16-20, SAE O-RING 20 7.0 FT 124435-004 TUBING-NYLON, 3/8 O.D. 21 1 124393-005 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.25 NPT 22 1 126354-005 FITTING-FEMALE CONNECTOR, 0.25 TUBE X 0.25 NPT 23 1 129545 GAUGE-SIGHT FLOW 24 1 125025 ORIFICE-LINE FILTER (0.040) 25 1 110419-005 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.25 NPT 26 3 121033-5 BUSHING-PIPE, BRASS, 0.50 NPT X 0.25 NPT 27 1 142125-5 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 2.38 28 1 7361-001 TEE-PIPE, BRASS, 0.12 NPT 29 4 128967-001 FITTING-ELBOW, 45° MALE, 0.25 TUBE X 0.12 NPT 30 5 121160 PLUG-PIPE, 1/8 NPT 31 1 140317 GROMMET-RUBBER 32 1 124393-012 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.25 NPT 33 0.25 FT 140326-04 TUBING-FUEL 34 1 7361-004 TEE-PIPE, BRASS, 0.50 NPT 35 2 2719 PLUG-PIPE, HEX SOCKET, 1/4 NPT 36 2 124349-015 FITTING-ELBOW, 90° MALE, 0.50 TUBE X 0.50 NPT 37 5.0 FT 124435-005 TUBING-NYLON, 1/2 O.D. 38 1 124393-004 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.12 NPT 39 1 126345 GAUGE-PRESSURE, LIQUID FILLED (0-200 P.S.I.) 40 1 122056 VALVE-CHECK 41 1 142125-3 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 1.50 42 1 122212 ELBOW-PIPE, BRASS, 0.12 NPT X 0.25 NPT 43 1 2057 PLUG-PIPE, 1/2 NPT 44 1 121033-1 BUSHING-PIPE, BRASS, 0.25 NPT X 0.12 NPT 45 0.25 FT 122636 ELBOW-PIPE, BRASS, 0.25 NPT


A 1 129732-050 KIT-LINE FILTER (includes gasket, bowl seal, filter element) B 1 20775 KIT-DIFFERENTIAL PILOT VALVE (includes diaphragm,

diaphragm gaskets, seat gasket, seat disk, seat ring) C 1 140406-904 O-RING, VITON D 1 129545-050 KIT-FLOW GAUGE (includes sightglass, viton seals) E 2 123157-008 O-RING


CONTROL PIPING GROUP (75 HP)(with differential pressure switches)143383-12


CONTROL PIPING GROUP (75 HP)(with differential pressure switches)



1 120496-4 VALVE-SOLENOID, 3-WAY (high pressure option) 5 33.0 FT 124435-003 TUBING-NYLON, 1/4 O.D. 6 1 121033-2 BUSHING-PIPE, BRASS, 0.38 NPT X 0.25 NPT 7 5 142125-1 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X CLOSE 8 8 124349-005 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.25 NPT 9 4 124349-004 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.12 NPT 10 2 90084 VALVE-SHUTTLE, 1/8 NPT 11 2 121034-2 TEE-PIPE, BRASS, 0.25 NPT 12 2 124349-010 FITTING-ELBOW, 90° MALE, 0.38 TUBE X 0.25 NPT 13 2 111098-002 NIPPLE-PIPE, BRASS, 0.12 NPT X 0.25 NPT X CLOSE 14 1 22455 CONNECTOR-ELECTRICAL, 1/2 15 1 8052 LOCKNUT-CONDUIT, 1/2 16 1 129203-003 COUPLING-BULKHEAD 17 1 6150 CROSS-PIPE, BRASS, 0.25 NPT 18 7.0 FT 140333 TUBE-STAINLESS STEEL, 0.25 O.D. 19 1 128886-003 FITTING-ELBOW, 0.25 TUBE X 7/16-20, SAE O-RING 20 7.0 FT 124435-004 TUBING-NYLON, 3/8 O.D. 21 2 124393-005 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.25 NPT 22 1 126354-005 FITTING-FEMALE CONNECTOR, 0.25 TUBE X 0.25 NPT 23 1 129545 GAUGE-SIGHT FLOW 24 1 125025 ORIFICE-LINE FILTER (0.040) 25 1 110419-005 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.25 NPT 26 4 121033-5 BUSHING-PIPE, BRASS, 0.50 NPT X 0.25 NPT 27 1 142125-5 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 2.38 28 1 7361-001 TEE-PIPE, BRASS, 0.12 NPT 29 4 128967-001 FITTING-ELBOW, 45° MALE, 0.25 TUBE X 0.12 NPT 30 5 121160 PLUG-PIPE, 1/8 NPT

Items 31 through 51 and the Component Maintenance Parts are on page 29.


143383-12





31 1 140317 GROMMET-RUBBER 32 2 124393-012 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.25 NPT 33 0.25 FT 140326-04 TUBING-FUEL 34 2 7361-004 TEE-PIPE, BRASS, 0.50 NPT 35 1 121033-1 BUSHING-PIPE, BRASS, 0.25 NPT X 0.12 NPT 36 3 124393-004 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.12 NPT 37 2 124393-010 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.12 NPT 38 2 140106-024 FITTING-ADAPTER, 7/16-20 X 1/4-4 NPTF, SAE O-RING 39 1 122636 ELBOW-PIPE, BRASS, 0.25 NPT 40 1 142947 VALVE-ANGLE, NEEDLE 41 1 121034-1 TEE-PIPE, BRASS, 0.12 NPT 42 1 142125-13 NIPPLE-BRASS, EXTRA STRONG, 0.12 NPT X CLOSE 43 1 124348-002 FITTING-TEE, MALE RUN, 0.25 TUBE X 0.12 NPT 44 1 2719 PLUG-PIPE, HEX SOCKET, 1/4 NPT 45 2 124349-015 FITTING-ELBOW, 90° MALE, 0.50 TUBE X 0.50 NPT 46 5.0 FT 124435-005 TUBING-NYLON, 1/2 O.D. 47 1 126345 GAUGE-PRESSURE, LIQUID FILLED (0-200 P.S.I.) 48 1 122056 VALVE-CHECK 49 1 142125-3 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 1.50 50 1 122212 ELBOW-PIPE, BRASS, 0.12 NPT X 0.25 NPT 51 1 2057 PLUG-PIPE, 1/2 NPT





CONTROL PIPING GROUP (100 HP, across the line)(less differential pressure switches)143383-21


CONTROL PIPING GROUP (100 HP, across the line)(less differential pressure switches)



1 120496-4 VALVE-SOLENOID, 3-WAY (high pressure option) 5 33.0 FT 124435-003 TUBING-NYLON, 1/4 O.D. 6 1 121033-2 BUSHING-PIPE, BRASS, 0.38 NPT X 0.25 NPT 7 5 142125-1 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X CLOSE 8 6 124349-005 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.25 NPT 9 3 124349-004 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.12 NPT 10 2 90084 VALVE-SHUTTLE, 1/8 NPT 11 2 121034-2 TEE-PIPE, BRASS, 0.25 NPT 12 1 124349-010 FITTING-ELBOW, 90° MALE, 0.38 TUBE X 0.25 NPT 13 2 111098-002 NIPPLE-PIPE, BRASS, 0.12 NPT X 0.25 NPT X CLOSE 14 1 22455 CONNECTOR-ELECTRICAL, 1/2 15 1 8052 LOCKNUT-CONDUIT, 1/2 16 1 129203-003 COUPLING-BULKHEAD 17 1 6150 CROSS-PIPE, BRASS, 0.25 NPT 18 7.0 FT 140333 TUBE-STAINLESS STEEL, 0.25 O.D. 19 1 128886-003 FITTING-ELBOW, 0.25 TUBE X 7/16-20, SAE O-RING 20 7.0 FT 124435-004 TUBING-NYLON, 3/8 O.D. 21 1 124393-005 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.25 NPT 22 1 126354-005 FITTING-FEMALE CONNECTOR, 0.25 TUBE X 0.25 NPT 23 1 129545 GAUGE-SIGHT FLOW 24 1 125025 ORIFICE-LINE FILTER (0.040) 25 1 110419-005 FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.25 NPT 26 3 121033-5 BUSHING-PIPE, BRASS, 0.50 NPT X 0.25 NPT 27 1 142125-5 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 2.38 28 1 7361-001 TEE-PIPE, BRASS, 0.12 NPT 29 4 128967-001 FITTING-ELBOW, 45° MALE, 0.25 TUBE X 0.12 NPT 30 3 121160 PLUG-PIPE, 1/8 NPT 31 1 140317 GROMMET-RUBBER 32 1 124393-012 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.25 NPT 33 0.25 FT 140326-04 TUBING-FUEL 34 1 7361-004 TEE-PIPE, BRASS, 0.50 NPT 35 2 2719 PLUG-PIPE, HEX SOCKET, 1/4 NPT 36 2 124349-015 FITTING-ELBOW, 90° MALE, 0.50 TUBE X 0.50 NPT 37 5.0 FT 124435-005 TUBING-NYLON, 1/2 O.D. 38 1 124393-004 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.12 NPT 39 1 126345 GAUGE-PRESSURE, LIQUID FILLED (0-200 P.S.I.) 40 1 2721 PLUG-PIPE, 1/2 NPT 41 1 122056 VALVE-CHECK 42 1 142125-3 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 1.50 43 1 122212 ELBOW-PIPE, BRASS, 0.12 NPT X 0.25 NPT 44 1 2057 PLUG-PIPE, 1/2 NPT 45 1 121033-1 BUSHING-PIPE, BRASS, 0.25 NPT X 0.12 NPT 46 1 122636 ELBOW-PIPE, BRASS, 0.25 NPT





CONTROL PIPING GROUP (100 HP, across the line)(with differential pressure switches)143383-22


CONTROL PIPING GROUP (100 HP, across the line)(with differential pressure switches)






CONTROL PIPING GROUP (100 HP, across the line)(with differential pressure switches)143383-22


CONTROL PIPING GROUP (100 HP, across the line)(with differential pressure switches)


31 1 140317 GROMMET-RUBBER 32 3 124393-012 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.25 NPT 33 0.25 FT 140326-04 TUBING-FUEL 34 2 7361-004 TEE-PIPE, BRASS, 0.50 NPT 35 1 121033-1 BUSHING-PIPE, BRASS, 0.25 NPT X 0.12 NPT 36 3 124393-004 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.12 NPT 37 2 124393-010 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.12 NPT 38 2 140106-024 FITTING-ADAPTER, 7/16-20 X 1/4-4 NPTF, SAE O-RING 39 1 122636 ELBOW-PIPE, BRASS, 0.25 NPT 40 1 142947 VALVE-ANGLE, NEEDLE 41 1 121034-1 TEE-PIPE, BRASS, 0.12 NPT 42 1 142125-13 NIPPLE-BRASS, EXTRA STRONG, 0.12 NPT X CLOSE 43 5.0 FT 124435-005 TUBING-NYLON, 1/2 O.D. 44 1 2719 PLUG-PIPE, HEX SOCKET, 1/4 NPT 45 2 124349-015 FITTING-ELBOW, 90° MALE, 0.50 TUBE X 0.50 NPT 46 1 126345 GAUGE-PRESSURE, LIQUID FILLED (0-200 P.S.I.) 47 1 122056 VALVE-CHECK 48 1 142125-3 NIPPLE-BRASS, EXTRA STRONG, 0.25 NPT X 1.50 49 1 122212 ELBOW-PIPE, BRASS, 0.12 NPT X 0.25 NPT 50 1 2057 PLUG-PIPE, 1/2 NPT





CONTROL PIPING GROUP (100 HP, wye-delta)

143383-23



143383-23




31 1 140317 GROMMET-RUBBER 32 3 124393-012 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.25 NPT 33 0.25 FT 140326-04 TUBING-FUEL 34 2 7361-004 TEE-PIPE, BRASS, 0.50 NPT 35 1 121033-1 BUSHING-PIPE, BRASS, 0.25 NPT X 0.12 NPT 36 3 124393-004 FITTING-MALE CONNECTOR, 0.25 TUBE X 0.12 NPT 37 2 124393-010 FITTING-MALE CONNECTOR, 0.38 TUBE X 0.12 NPT 38 2 140106-024 FITTING-ADAPTER, 7/16-20 X 1/4-4 NPTF, SAE O-RING 39 1 23543-002 REGULATOR-PRESSURE 40 1 142947 VALVE-ANGLE, NEEDLE 41 1 121034-1 TEE-PIPE, BRASS, 0.12 NPT 42 1 142125-13 NIPPLE-BRASS, EXTRA STRONG, 0.12 NPT X CLOSE 43 5.0 FT 124435-005 TUBING-NYLON, 1/2 O.D. 44 1 2719 PLUG-PIPE, HEX SOCKET, 1/4 NPT 45 2 124349-015 FITTING-ELBOW, 90° MALE, 0.50 TUBE X 0.50 NPT 46 2 122636 ELBOW-PIPE, BRASS, 0.25 NPT 47 1 140718 GAUGE-PRESSURE 48 1 126345 GAUGE-PRESSURE, LIQUID FILLED (0-200 P.S.I.) 49 1 122056 VALVE-CHECK 50 1 122212 ELBOW-PIPE, BRASS, 0.12 NPT X 0.25 NPT 51 1 2057 PLUG-PIPE, 1/2 NPT



diaphragm gaskets, seat gasket, seat disk, seat ring) C 3 140406-904 O-RING, VITON D 1 129545-050 KIT-FLOW GAUGE (includes sightglass, viton seals) E 1 23543-050 KIT-PRESSURE REGULATOR F 2 123157-008 O-RING


GAUGE GROUPS (percent capacity)(optional)142295-3


GAUGE GROUPS (percent capacity)(optional)

142295-003 142295-005(L/CABINET) (W/CABINET)

1 1 128663 ! GAUGE-PERCENT CAPACITY 2 1 125260-001 ! REDUCER-PIPE, BRASS, 1/4 NPT X 1/8 NPT 3 1 142125-13 ! NIPPLE-BRASS, EXTRA STRONG,

0.12 NPT X CLOSE 4 1 122056 ! VALVE-CHECK 5 2 124349-004 ! FITTING-ELBOW, 90° MALE, 0.25 TUBE X 0.12 NPT 6 5.0 FT 124435-003 ! TUBING-NYLON, 1/4 O.D. 7 1 124349-005 N/A FITTING-ELBOW, 90° MALE,

0.25 TUBE X 0.25 NPT 8 1 143011 N/A PANEL-GAUGE 9 4 124370-K02 N/A LOCKNUT, 5/16-18 UNC 10 4 110428W025 N/A WASHER-FLAT, 1/4 11 4 110511-K10 N/A SCREW-TAP, ZINC, 5/16-18 UNC X 0.75


A 2 123157-008 ! O-RING



RESERVOIR GROUPS

142927-1


RESERVOIR GROUPS

142927-001 142927-002(75 HP) (100 HP)

1 1 143320-175 ! RESERVOIR-AIR/FLUID 2 1 124487-003 124487-018 SEPARATOR-AIR/FLUID, PRIMARY 3 1 141966-6 ! VALVE-PRESSURE RELIEF 4 1 129844-162 ! CAP-FILLER, SAE O-RING 5 1 129843-188 ! SIGHTGLASS, SAE O-RING 6 1 4729 ! PLUG-PIPE, 3/8 NPT 7 1 142299 ! FITTING-STRAIGHT, 0.25 TUBE X 0.25 NPT 8 3 124370-N02 ! LOCKNUT, 1/2-13 UNC 9 9 110428W050 ! WASHER-FLAT, 1/2 10 3 123478-N15 ! SCREW-CAP, 1/2-13 UNC X 1.50,

GRADE 5 (@ 55 FT-LBS) 11 1.0 FT 129164-500 ! TUBING-CLEAR VINYL, 1/2 I.D. 12 1 140323-9 ! TUBE-SEPARATOR DRAIN 13 1 143355-003 ! FITTING-ELBOW, 0.50 TUBE X 3/4-16,

SAE O-RING 14 1 129730-050 ! VALVE-QUARTER TURN, SAE O-RING 15 1 140106-003 ! FITTING-ADAPTER, 3/4-16 X 3/8-8 NPTF,

SAE O-RING 16 2 128968-010 ! FITTING-HOSE, BARBED,

0.50 HOSE X 0.38 NPT 17 2 128176-015 ! CLAMP-HOSE 18 1 128193-2 ! LABEL-FLUID DRAIN 19 1 129203-004 ! COUPLING-BULKHEAD


A 8 123478-Q18 ! SCREW-CAP, 5/8-11 UNC X 2.25,GRADE 5 (@ 110 FT-LBS)

B 8 123115-10C ! LOCKWASHER, 5/8 C 1 140406-920 ! O-RING, VITON D 1 140406-924 ! O-RING, VITON E 3 140406-908 ! O-RING, VITON




INLET VALVE GROUP (75 HP)142993


INLET VALVE GROUP (75 HP)142993


1/1 1 141608 GASKET-INLET VALVE1/2 4 142578-N15 SCREW-CAP, ZINC, 1/2-13 UNC X 1.50, GRADE 5 (@ 23 FT-LBS)1/3 1 126646 HOUSING-INLET VALVE1/4 1 122995 ASSEMBLY-INLET VALVE PLATE1/5 1 124368-N02 NUT-JAM, 1/2-13 UNC1/6 1 128720-001 SCREW-HEX, 1/2-13 UNC X 5.00, GRADE 5 (@ 55 FT-LBS)1/7 1 123092 SPRING1/8 1 123549-003 GASKET1/9 1 126644 CYLINDER-INLET VALVE1/10 1 126649 SPRING-INLET VALVE1/11 1 126648 SHAFT-INLET VALVE1/12 1 126647 WASHER-FLAT, 9/161/13 1 126460-350 CUP-PISTON1/14 1 1478-1 WASHER-FLAT, STEEL1/15 1 123478-N12 SCREW-CAP, 1/2-13 UNC X 1.00, GRADE 5 (@ 55 FT-LBS)1/16 1 126645 PLATE-COVER1/17 6 123478-L15 SCREW-CAP, 3/8-16 UNC X 1.50, GRADE 5 (@ 23 FT-LBS)1/18 1 141258 GASKET-INLET VALVE1/19 5 123115-08C LOCKWASHER, 1/21/20 6 123115-06C LOCKWASHER, 3/8

2 1 128307 PLATE-ADAPTER, INLET VALVE 3 1 123549-002 GASKET-INLET VALVE 4 8 123478-N15 SCREW-CAP, 1/2-13 UNC X 1.50, GRADE 5 (@ 55 FT-LBS) 5 8 123115-08C LOCKWASHER, 1/2



INLET VALVE GROUP (100 HP, across the line)125323-005


INLET VALVE GROUP (100 HP, across the line)125323-005


1 1 143057-005 HOUSING-INLET VALVE 2 1 141075 ASSEMBLY-AIR CYLINDER 3 8 123115-06C LOCKWASHER, 3/8 4 1 123549-002 GASKET-INLET VALVE 5 8 123478-N15 SCREW-CAP, 1/2-13 UNC X 1.50, GRADE 5 (@ 55 FT-LBS) 6 8 123115-08C LOCKWASHER, 1/2 7 1 124368-N02 NUT-JAM, 1/2-13 UNC 8 1 128720-001 SCREW-HEX, 1/2-13 UNC X 5.00, GRADE 5 (@ 55 FT-LBS) 9 1 122379 SPRING 10 1 123157-018 O-RING 11 1 122372-2 PLATE-INLET VALVE 12 1 122377 GASKET 13 8 123478-L12 SCREW-CAP, 3/8-16 UNC X 1.00, GRADE 5 (@ 23 FT-LBS)


A 1 122375-050 KIT-HEAD ASSEMBLY B 1 124970 SPRING C 1 123467 KIT-SPRING RETURN DIAPHRAGM



INLET VALVE GROUP (100 HP, wye-delta)143073-1


INLET VALVE GROUP (100 HP, wye-delta)143073-1


1 1 123549-002 GASKET-INLET VALVE 2 9 123478-N15 SCREW-CAP, 1/2-13 UNC X 1.50, GRADE 5 (@ 55 FT-LBS) 3 1 143057-005 HOUSING-INLET VALVE 4 8 123478-L12 SCREW-CAP, 3/8-16 UNC X 1.00, GRADE 5 (@ 23 FT-LBS) 5 1 122372-3 ASSEMBLY-INLET VALVE PLATE 6 1 128713 SPRING 7 1 123115-08Z LOCKWASHER-ZINC, 1/2 8 1 124368-N02 NUT-JAM, 1/2-13 UNC 9 1 122377 GASKET 10 1 128715 ASSEMBLY-INLET VALVE CYLINDER 11 1 128708 SEAL-SHAFT, INLET VALVE 12 1 128714-1 SPRING-INLET VALVE 13 1 128712-1 SHAFT-INLET VALVE 14 1 128717 PISTON-INLET VALVE 15 1 128720-001 SCREW-HEX, 1/2-13 UNC X 5.00, GRADE 5 (@ 55 FT-LBS) 16 1 128711 DIAPHRAGM-INLET VALVE 17 1 128716 PLATE-COVER 18 1 2719 PLUG-PIPE, HEX SOCKET, 1/4 NPT 19 16 123115-08Z LOCKWASHER-ZINC, 1/2 20 7 123478-N16 SCREW-CAP, 1/2-13 UNC X 1.75, GRADE 5 (@ 55 FT-LBS)



AIR PIPING GROUPS (air-cooled)


AIR PIPING GROUPS (air-cooled)

142994-005 142994-001(W/CABINET) (L/CABINET)

1 2 23991 ! FITTING-MALE CONNECTOR, 2.00 TUBE X 2.00 NPT 2 1 143244-001 ! TUBE-FORMED, STEEL, 2.00 O.D. 3 1 128691-002 ! VALVE-CHECK, MINIMUM PRESSURE 4 1 124827-200 ! SEPARATOR-MOISTURE 5 1 125938-038 ! NIPPLE-PIPE, 1.25 NPT X 5.50 6 1 142939 ! BUSHING-PIPE, BRASS, 0.50 NPT X 0.75 NPT 7 1 3535 ! BUSHING-PIPE, 0.38 NPT X 0.25 NPT 8 1 2713 ! DRAINCOCK-1/4 NPT 9 1 126023-001 N/A NIPPLE-PIPE, GALVANIZED, 2.00 NPT X CLOSE 10 2 22629 N/A ELBOW-PIPE, GALVANIZED, 2.00 NPT 11 1 126023-024 N/A NIPPLE-PIPE, GALVANIZED, 2.00 NPT X 3.75


A 1 128691-052 ! KIT-MINIMUM PRESSURE CHECK VALVE B 1 124827-052 ! KIT-MOISTURE SEPARATOR (includes item C) C 1 124827-051 ! GASKET



AIR PIPING GROUP (water-cooled)


142994-003 142994-004(75 HP) (100 HP)

1 2 110419-024 ! FITTING-ELBOW, 90° MALE, 2.00 TUBE X 2.00 NPT 2 1 143244-008 143244-005 TUBE-FORMED, STEEL, 2.00 O.D. 3 2 110511-K10 ! SCREW-TAP, ZINC, 5/16-18 UNC X 0.75 4 1 143244-007 143244-006 TUBE-FORMED, STEEL, 2.00 O.D. 5 1 124827-200 ! SEPARATOR-MOISTURE 6 1 125940-058 ! NIPPLE-PIPE, 2.00 NPT X 8.00 7 1 6366 ! COUPLING-PIPE, 2.00 NPT 8 1 142150-1 142746 BRACKET-COOLER SUPPORT 9 1 143554-1 ! BRACKET-COOLER 10 1 6306 ! U-BOLT, 1/4-18 UNC 11 1 23731 ! U-BOLT, 1/2-13 UNC 12 1 142744 142745 BRACKET-COOLER SUPPORT 13 1 4463 ! ELBOW-PIPE, 2.00 NPT 14 1 2713 ! DRAINCOCK-1/4 NPT 15 2 124370-N02 ! LOCKNUT, 1/2-13 UNC 16 2 23991 ! FITTING-MALE CONNECTOR, 2.00 TUBE X 2.00 NPT 17 1 128691-002 ! VALVE-CHECK, MINIMUM PRESSURE 18 1 125938-038 ! NIPPLE-PIPE, 1.25 NPT X 5.50 19 1 142939 ! BUSHING-PIPE, BRASS, 0.50 NPT X 0.75 NPT 20 1 3535 ! BUSHING-PIPE, 0.38 NPT X 0.25 NPT


A 1 124827-052 ! KIT-MOISTURE SEPARATOR (includes item B) B 1 124827-051 ! GASKET-MOISTURE SEPARATOR C 1 128691-052 ! KIT-MINIMUM PRESSURE CHECK VALVE


AIR PIPING GROUP (water-cooled)



COOLER GROUPS (air-cooled)


COOLER GROUPS (air-cooled)

142990-003(100 HP, 60Hz)

142990-001 (100 HP, 50Hz,(75 HP, 60Hz) L/CABINET)

1 1 142218 142689 SHROUD-COOLER, VENTURI 2 1 142348 ! BRACKET-SUPPORT, RH 3 1 142349 ! BRACKET-SUPPORT, LH 4 1 142560-02 ! BRACKET-SUPPORT 5 1 142683 ! GUARD-FAN, 30" 6 1 142219 142681-001 COOLER-COMBINATION, 200 PSI 7 6.0 FT 141528 ! SEAL-AIR 8 1 126511-055 126511-049 FAN-5 BLADE, 30.0 O.D. 9 4 123478-N15 ! SCREW-CAP, 1/2-13 UNC X 1.50,

GRADE 5 (@ 55 FT-LBS) 10 6 141631-L10 ! SCREW-CAP, 3/8-16 UNC X 0.75,

GRADE 5 (@ 23 FT-LBS) 11 11 141631-K10 ! SCREW-CAP, 5/16-18 UNC X 0.75,

GRADE 5 (@ 23 FT-LBS) 12 6 112272-L02 ! NUT-HEX, SELF-LOCKING, ZINC, 3/8-16 UNC 13 8 110511-K12 ! SCREW-TAPTITE, ZINC, 5/16-18 UNC X 1.00 14 8 112272-K02 ! NUT-HEX, SELF LOCKING, ZINC, 5/16-18 UNC 15 8 110428W031 ! WASHER-FLAT, 5/16 16 4 110428W050 ! WASHER-FLAT, 1/2 17 4 123115-08C ! LOCKWASHER, 1/2 18 8 123478-L14 ! SCREW-CAP, 3/8-16 UNC X 1.25,

GRADE 5 (@ 23 FT-LBS) 19 8 123115-06C ! LOCKWASHER, 3/8 20 8 124364-L02 ! NUT-HEX, 3/8-16 UNC

142990-005142990-002 (100 HP, 50Hz,

(75 HP, 50Hz) W/CABINET) 1 1 142218 142689 SHROUD-COOLER, VENTURI 2 1 142348 ! BRACKET-SUPPORT, RH 3 1 142349 ! BRACKET-SUPPORT, LH 4 1 142560-02 ! BRACKET-SUPPORT 5 1 142683 ! GUARD-FAN, 30" 6 1 142219 142681-001 COOLER-COMBINATION, 200 PSI 7 6.0 FT 141528 ! SEAL-AIR 8 1 126511-060 126511-062 FAN-5 BLADE, 30.0 O.D. 9 4 123478-N15 ! SCREW-CAP, 1/2-13 UNC X 1.50,

GRADE 5 (@ 55 FT-LBS) 10 6 141631-L10 ! SCREW-CAP, 3/8-16 UNC X 0.75,

GRADE 5 (@ 23 FT-LBS) 11 11 141631-K10 ! SCREW-CAP, 5/16-18 UNC X 0.75,

GRADE 5 (@ 23 FT-LBS) 12 6 112272-L02 ! NUT-HEX, SELF-LOCKING, ZINC, 3/8-16 UNC 13 8 110511-K12 ! SCREW-TAPTITE, ZINC, 5/16-18 UNC X 1.00 14 8 112272-K02 ! NUT-HEX, SELF LOCKING, ZINC, 5/16-18 UNC 15 8 110428W031 ! WASHER-FLAT, 5/16 16 4 110428W050 ! WASHER-FLAT, 1/2 17 4 123115-08C ! LOCKWASHER, 1/2 18 8 123478-L14 ! SCREW-CAP, 3/8-16 UNC X 1.25,

GRADE 5 (@ 23 FT-LBS) 19 8 123115-06C ! LOCKWASHER, 3/8 20 8 124364-L02 ! NUT-HEX, 3/8-16 UNC




FLUID PIPING GROUP (75 HP, air-cooled)142995-001


1 3 129208-021 FITTING-ADAPTER, 1-5/16-12 X 1-5/8-12, SAE O-RING 2 4 140676-018 FITTING-ELBOW, 1.00 TUBE X 1-5/16-12, SAE O-RING 3 1 140674-006 FITTING-TEE, UNION, 1.00 TUBE, SAE O-RING 4 1 140682-020 FITTING-CONNECTOR, 1.00 TUBE X 1-5/16-12, SAE O-RING 5 2 129208-024 FITTING-ADAPTER, 1-5/16-12 X 1-7/8-12, SAE O-RING 6 1 141110-010 FITTING-UNION, 1.00 TUBE, SAE O-RING 7 10 140679-007 FITTING-NUT, 1.00 O.D. TUBE 8 10 140680-006 FITTING-SLEEVE, 1.00 TUBE 9 1 140536-1 VALVE-THERMAL CARTRIDGE 10 1 142243 ELEMENT-FLUID FILTER 11 1 142999-6 TUBE-FORMED, STEEL, 1.00 O.D. 12 1 142999-7 TUBE-FORMED, STEEL, 1.00 O.D. 13 1 142999-8 TUBE-FORMED, STEEL, 1.00 O.D. 14 1 142999-9 TUBE-FORMED, STEEL, 1.00 O.D. 15 1 142999-10 TUBE-FORMED, STEEL, 1.00 O.D.


A 3 140406-920 O-RING, VITON B 5 140406-916 O-RING, VITON C 10 140675-006 O-RING/FACE SEAL, VITON D 2 140406-924 O-RING, VITON E 1 22749-123 O-RING, VITON


FLUID PIPING GROUP (100 HP, air-cooled)142995-002


1 2 129208-025 FITTING-ADAPTER, 1-5/8-12 X 1-7/8-12, SAE O-RING 2 4 140676-021 FITTING-ELBOW, 1.25 TUBE X 1-5/8-12, SAE O-RING 3 1 140674-007 FITTING-TEE, UNION, 1.25 TUBE, SAE O-RING 4 1 140682-024 FITTING-CONNECTOR, 1.25 TUBE X 1-5/8-12, SAE O-RING 5 1 141110-012 FITTING-UNION, 1.25 TUBE, SAE O-RING 6 10 140679-008 FITTING-NUT, 1.25 O.D. TUBE 7 10 140680-007 FITTING-SLEEVE, 1.25 TUBE 8 1 140536-1 VALVE-THERMAL CARTRIDGE 9 1 142243 ELEMENT-FLUID FILTER 10 1 142999-1 TUBE-FORMED, STEEL, 1.25 O.D. 11 1 142999-2 TUBE-FORMED, STEEL, 1.25 O.D. 12 1 142999-3 TUBE-FORMED, STEEL, 1.25 O.D. 13 1 142999-4 TUBE-FORMED, STEEL, 1.25 O.D. 14 1 142999-5 TUBE-FORMED, STEEL, 1.25 O.D.


A 2 140406-924 O-RING, VITON B 5 140406-920 O-RING, VITON C 10 140675-007 O-RING/FACE SEAL, VITON D 1 22749-123 O-RING, VITON


FLUID PIPING GROUP (75 HP, water-cooled)142995-003


1 1 143498-3 TUBE-STEEL, 1.00 O.D. 2 1 142150-2 BRACKET-COOLER SUPPORT 3 1 129770-188 PLUG-PIPE, 1-7/8-12, SAE O-RING 4 3 142409-003 TUBE-STEEL, 1.00 O.D. 5 1 129208-024 FITTING-ADAPTER, 1-5/16-12 X 1-7/8-12, SAE O-RING 6 1 140681-015 FITTING-UNION, 1.00 TUBE X 1.00 NPTF 7 3 140676-018 FITTING-ELBOW, 1.00 TUBE X 1-5/16-12, SAE O-RING 8 8 140679-007 FITTING-NUT, 1.00 O.D. TUBE 9 8 140680-006 FITTING-SLEEVE, 1.00 TUBE 10 1 125938-026 NIPPLE-PIPE, 1.25 NPT X 4.00 11 1 124420-037 TEE-PIPE, 1.25 NPT X 0.50 NPT X 1.00 NPT 12 1 129208-021 FITTING-ADAPTER, 1-5/16-12 X 1-5/8-12, SAE O-RING 13 2 141110-010 FITTING-UNION, 1.00 TUBE, SAE O-RING 14 4 141631-K10 SCREW-CAP, 5/16-18 UNC X 0.75, GRADE 5 (@ 23 FT-LBS) 15 4 112272-K02 NUT-HEX, SELF-LOCKING, ZINC, 5/16-18 UNC 16 1 142150-4 BRACKET-COOLER SUPPORT 17 4 110511-K10 SCREW-TAP, ZINC, 5/16-18 UNC X 0.75 18 1 143566 PLUG-THERMAL VALVE 19 1 142243 ELEMENT-FLUID FILTER


A 2 140406-924 O-RING, VITON B 8 140675-006 O-RING/FACE SEAL, VITON C 3 140406-916 O-RING, VITON D 1 140406-920 O-RING, VITON E 1 22749-123 O-RING, VITON






1 1 143546-1 TUBE-FORMED, STEEL, 1.25 O.D. 2 2 142150-2 BRACKET-COOLER SUPPORT 3 1 129770-188 PLUG-PIPE, 1-7/8-12, SAE O-RING 4 3 142410-004 TUBE-FORMED, STEEL, 1.25 O.D. 5 1 129208-025 FITTING-ADAPTER, 1-5/8-12 X 1-7/8-12, SAE O-RING 6 1 140681-017 FITTING-UNION, 1.25 TUBE X 1.25 NPTF 7 3 140676-021 FITTING-ELBOW, 1.25 TUBE X 1-5/8-12, SAE O-RING 8 8 140679-008 FITTING-NUT, 1.25 O.D. TUBE 9 8 140680-007 FITTING-SLEEVE, 1.25 TUBE 10 1 125938-026 NIPPLE-PIPE, 1.25 NPT X 4.00 11 1 21741 TEE-PIPE, 1.25 NPT X 0.50 NPT X 1.25 NPT 12 2 141110-012 FITTING-UNION, 1.25 TUBE, SAE O-RING 13 1 143566 PLUG-THERMAL VALVE 14 4 141631-K10 SCREW-CAP, 5/16-18 UNC X 0.75, GRADE 5 (@ 23 FT-LBS) 15 4 112272-K02 NUT-HEX, SELF-LOCKING, ZINC, 5/16-18 UNC 16 1 142243 ELEMENT-FLUID FILTER 17 4 110511-K10 SCREW-TAP, ZINC, 5/16-18 UNC X 0.75


A 2 140406-924 O-RING, VITON B 8 140675-007 O-RING/FACE SEAL, VITON C 3 140406-920 O-RING, VITON D 1 22749-123 O-RING, VITON




WATER PIPING GROUP (75 HP, fresh water)142998-001

1 2 110419-020 FITTING-ELBOW, 90° MALE, 1.00 TUBE X 1.00 NPT 2 1 142549-001 TUBE-FORMED, STEEL, 1.00 O.D. 3 2 21730 ELBOW-PIPE, GALVANIZED, 1.00 NPT 4 1 126020-076 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 10.75 5 1 23219-1 VALVE-WATER REGULATING 6 2 126020-018 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 3.00 7 1 126020-064 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 8.75 8 2 21740 COUPLING-PIPE, GALVANIZED, 1.00 NPT 9 2 120317 U-BOLT, 5/16-18 UNC 10 1 22709-18 HEAT EXCHANGER-AFTERCOOLER 11 1 22708-36 HEAT EXCHANGER-FLUID COOLER 12 1 22431 VALVE-SOLENOID, 2-WAY 13 2 21731 ELBOW-PIPE, GALVANIZED, 1.00 NPT 14 2 126020-102 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 13.50


A 2 22708-725 BONNET-COOLER, IN/OUT END B 2 22708-727 GASKET-COOLER, IN/OUT END C 2 22708-726 BONNET-COOLER, RETURN END D 2 22708-728 GASKET-COOLER, RETURN END



WATER PIPING GROUP (100 HP, fresh water)142998-002

1 2 110419-020 FITTING-ELBOW, 90° MALE, 1.00 TUBE X 1.00 NPT 2 1 142549-001 TUBE-FORMED, STEEL, 1.00 O.D. 3 2 21730 ELBOW-PIPE, GALVANIZED, 1.00 NPT 4 1 126020-028 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 4.25 5 1 23219-1 VALVE-WATER REGULATING 6 2 126020-018 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 3.00 7 1 126020-032 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 4.75 8 2 21740 COUPLING-PIPE, GALVANIZED, 1.00 NPT 9 2 120317 U-BOLT, 5/16-18 UNC 10 1 22709-19 HEAT EXCHANGER-AFTERCOOLER 11 1 22708-30 HEAT EXCHANGER-FLUID COOLER 12 1 22431 VALVE-SOLENOID, 2-WAY 13 2 21731 ELBOW-PIPE, GALVANIZED, 1.00 NPT 14 2 125868-016 BUSHING-PIPE, 1.25 NPT X 1.00 NPT 15 4 126020-001 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X CLOSE 16 2 126020-010 NIPPLE-PIPE, GALVANIZED, 1.00 NPT X 2.00 17 4 122171 ELBOW-PIPE, GALVANIZED, 1.00 NPT X 45°


A 1 22708-825 BONNET-COOLER, IN/OUT END B 1 22708-827 GASKET-COOLER, IN/OUT END C 1 22708-826 BONNET-COOLER, RETURN END D 1 22708-828 GASKET-COOLER, RETURN END E 2 22708-725 BONNET-COOLER, IN/OUT END F 2 22708-727 GASKET-COOLER, IN/OUT END G 2 22708-726 BONNET-COOLER, RETURN END H 2 22708-728 GASKET-COOLER, RETURN END



1 2 126020-34B NIPPLE-PIPE, BRASS, 1.00 NPT X 5.00 2 2 126020-26B NIPPLE-PIPE, BRASS, 1.00 NPT X 4.00 3 3 142310-06 ELBOW-PIPE, 1.00 NPT 4 3 141650-102 NIPPLE-PIPE, BRASS, 1.00 NPT X 13.50 5 1 23219-1 VALVE-WATER REGULATING 6 2 141650-018 NIPPLE-PIPE, BRASS, 1.00 NPT X 3.00 7 1 141650-064 NIPPLE-PIPE, BRASS, 1.00 NPT X 8.75 8 2 142309-06 COUPLING-PIPE, 1.00 NPT 9 2 120317 U-BOLT, 5/16-18 UNC 10 1 124061-009 HEAT EXCHANGER-AFTERCOOLER 11 1 124060-015 HEAT EXCHANGER-FLUID COOLER 12 5 141829-006 ELBOW-PIPE, BRASS, 1.00 NPT 13 1 142311-07 UNION-PIPE, 1.00 NPT


A 1 124061-225 BONNET-COOLER, IN/OUT END B 1 22709-228 GASKET-COOLER, RETURN END C 1 124061-226 BONNET-COOLER, RETURN END D 1 22708-728 GASKET-COOLER, RETURN END

WATER PIPING GROUP (75 HP, sea water)142998-003



WATER PIPING GROUP (100 HP, sea water)142998-004


1 2 126020-34B NIPPLE-PIPE, BRASS, 1.00 NPT X 5.00 2 2 126020-26B NIPPLE-PIPE, BRASS, 1.00 NPT X 4.00 3 4 142310-06 ELBOW-PIPE, 1.00 NPT 4 1 141650-028 NIPPLE-PIPE, BRASS, 1.00 NPT X 4.25 5 1 23219-1 VALVE-WATER REGULATING 6 2 141650-018 NIPPLE-PIPE, BRASS, 1.00 NPT X 3.00 7 1 141650-067 NIPPLE-PIPE, BRASS, 1.00 NPT X 9.12 8 2 142309-06 COUPLING-PIPE, 1.00 NPT 9 2 120317 U-BOLT, 5/16-18 UNC 10 1 124061-014 HEAT EXCHANGER-AFTERCOOLER 11 1 124060-016 HEAT EXCHANGER-FLUID COOLER 12 4 141829-006 ELBOW-PIPE, BRASS, 1.00 NPT 13 1 142311-07 UNION-PIPE, 1.00 NPT 14 2 121033-14 BUSHING-PIPE, BRASS, 1.00 NPT X 1.25 NPT 15 4 126020-01B NIPPLE-PIPE, BRASS, 1.00 NPT X CLOSE 16 1 126020-10B NIPPLE-PIPE, BRASS, 1.00 NPT X 2.00 17 4 143607-006 ELBOW-PIPE, BRASS, 1.00 NPT X 45°


A 1 124060-125 BONNET-COOLER, IN/OUT END B 1 22709-528 GASKET-COOLER C 1 124060-126 BONNET-COOLER, RETURN END D 1 22709-828 GASKET-COOLER, RETURN END


AIR FILTER GROUPS (75 HP)



1 1 126039-017 ! NIPPLE-PIPE, 3.50 NPT X 3.00, TOE 2 2 110423-072 ! CLAMP-HOSE 3 1 20418 ! ELBOW-RUBBER 4 1 22864-4 ! FILTER-AIR 5 1 120045 ! BAND-AIR FILTER 6 1 126859 ! BRACKET-AIR FILTER 7 2 123478-L12 ! SCREW-CAP, 3/8-16 UNC X 1.00,

GRADE 5 (@ 23 FT-LBS) 8 2 123115-06C ! LOCKWASHER, 3/8 9 2 124364-L02 ! NUT-HEX, 3/8-16 UNC 10 2 110428W038 ! WASHER-FLAT, 3/8 11 1 20187 N/A HOOD-AIR FILTER


A 1 23458-4 ! ELEMENT-AIR FILTER B 1 121291 ! COVER-DUST






1 1 126039-017 ! NIPPLE-PIPE, 3-1/2 NPT X 3.00 2 2 110423-072 ! CLAMP-HOSE 3 1 20418 ! ELBOW-RUBBER 4 1 22864-4 ! FILTER-AIR 5 1 120045 ! BAND-AIR FILTER 6 1 142987 ! BRACKET-AIR FILTER 7 2 123478-L12 ! SCREW-CAP, 3/8-16 UNC X 1.00,

GRADE 5 (@ 23 FT-LBS) 8 2 123115-06C ! LOCKWASHER, 3/8 9 2 124364-L02 ! NUT-HEX, 3/8-16 UNC 10 1 123617-003 ! BUSHING-PIPE, 5.00 NPT X 3.50 NPT 11 2 110428W038 ! WASHER-FLAT, 3/8 12 1 20187 N/A HOOD-AIR FILTER


A 1 23458-4 ! ELEMENT-AIR FILTER B 1 121291 ! COVER-DUST





CABINET GROUPS (air-cooled)


CABINET GROUPS (air-cooled)

143454-001 143456-001143454-002 143456-002

(75 HP) (100 HP)

1 1 142763-10 ! PANEL-DOOR POST 2 1 142763-11 ! PANEL-END 3 1 142763-12 ! PANEL-CENTER DIVIDER 4 1 142763-13 ! PANEL-INLET 5 1 142763-14 ! PANEL-SIDE, REAR 6 2 142763-25 ! PANEL-CORNER POST 7 1 142763-26 ! PANEL-SIDE, FRONT 8 2 142763-21 ! PANEL-DOOR POST 9 1 142763-22 ! PANEL-DOOR 10 2 142763-23 ! PANEL-DOOR 11 2 142763-24 ! PANEL-CORNER POST 12 3 142763-15 ! PANEL-DOOR 13 1 142763-16 ! PANEL-TOP 14 1 142763-17 142763-18 PANEL-TOP, AIR OUT 15 1 142763-19 142763-20 PANEL-COOLER OUTLET 16 1 142763-27 ! PANEL-BLANK (less gauge)

1 142763-28 ! PANEL-GAUGE (with gauge) 17 8 141526-1 ! HINGE-CABINET 18 48 142578-J07 ! SCREW-CAP, ZINC, 1/4-20 UNC X 0.50,

GRADE 5 (@ 6 FT-LBS) 19 52 141575-J07 ! SCREW-PAN HEAD, 1/4-20 UNC X 0.50 20 0.7 FT 20579 ! DAMPENER-VIBRATION 21 10.0 FT 141528 ! SEAL-AIR 22 12 128954-2 ! LATCH-DOOR, QUARTER TURN 23 4 141526-2 ! HINGE-CABINET 24 16 110511-K10 ! SCREW-TAP, ZINC, 5/16-18 UNC X 0.75 25 4 141991-1 ! COVER-BASE 26 8.3 FT 141527-1 ! TRIM-PANEL 27 28 110511-J07 ! SCREW-TAP, ZINC, 1/4-20 UNC X 0.50




CABINET GROUPS (water-cooled)

143455


CABINET GROUPS (water-cooled)

1 1 142763-10 PANEL-DOOR POST 2 1 142763-11 PANEL-END 3 1 142763-12 PANEL-CENTER DIVIDER 4 1 142763-13 PANEL-INLET 5 1 142763-14 PANEL-SIDE, REAR 6 2 142763-25 PANEL-CORNER POST 7 1 142763-26 PANEL-SIDE, FRONT 8 2 142763-21 PANEL-DOOR POST 9 1 142763-22 PANEL-DOOR 10 2 142763-23 PANEL-DOOR 11 2 142763-24 PANEL-CORNER POST 12 3 142763-15 PANEL-DOOR 13 1 142763-16 PANEL-TOP 14 1 142763-17 PANEL-TOP, AIR OUT 15 1 142763-29 PANEL-FAN 16 1 142763-27 PANEL-BLANK (less gauge)

1 142763-28 PANEL-GAUGE (with gauge) 17 1 141223 GUARD-FAN 18 8 141526-1 HINGE-CABINET 19 48 142578-J07 SCREW-CAP, ZINC, 1/4-20 UNC X 0.50,

GRADE 5 (@ 6 FT-LBS) 20 52 141575-J07 SCREW-PAN HEAD, 1/4-20 UNC X 0.50 21 0.7 FT 20579 DAMPENER-VIBRATION 22 10.0 FT 141528 SEAL-RUBBER 23 12 128954-2 LATCH-DOOR, QUARTER TURN 24 4 141526-2 HINGE-CABINET 25 16 110511-K10 SCREW-TAP, ZINC, 5/16-18 UNC X 0.75 26 4 141991-1 COVER-BASE 27 8.3 FT 141527-1 TRIM-PANEL 28 8 110428W031 WASHER-FLAT, 5/16 29 1 126511-034 FAN-8 BLADE, 16.0 O.D. 30 4 112272-K02 NUT-HEX, SELF-LOCKING, ZINC, 5/16-18 UNC 31 1 143061 GUARD-FAN 32 26 110511-J07 SCREW-TAP, ZINC, 1/4-20 UNC X 0.50 33 4 110511-K14 SCREW-TAP, ZINC, 5/16-18 UNC X 1.25 34 1 * ASSEMBLY-STARTER, VENT FAN 35 4 123115-05C LOCKWASHER, 5/16

* Part numbers listed in tabulation below.@ Indicates torque value in foot pounds (lubricated threads).

ITEM 34 VENT FAN STARTER ASSEMBLY

OPD TEFC200V 142342C001 142342C007230V 142342C002 142342C008380V 142342C005 142342C011415V 142342C006 142342C012460V 142342C003 142342C009575V 142342C004 142342C010



DECAL GROUPS (air-cooled)


1 1 143194 SHEET-SAFETY DECALS2 1 128198 LABEL-GENUINE QUINCY COMPONENTS3 1 110690-001 ENVELOPE-PLASTIC4* 1 142247-75A DECAL-QSF 75, 100 PSI

1 142247-75B DECAL-QSF 75, 125 PSI1 142247-75C DECAL-QSF 75, 150 PSI1 142247-10A DECAL-QSF 100, 100 PSI1 142247-10B DECAL-QSF 100, 125 PSI1 142247-10C DECAL-QSF 100, 150 PSI

5 1 142325 DECAL-FLUID LEVEL6 1 22177 TAG-FLUID TYPE SHIPPED WITH UNIT7** 1 128425 DECAL-THIS MACHINE IS PROTECTED WITH QUINSYN

1 128426 DECAL-THIS MACHINE IS PROTECTED WITH QUINSYN-F1 142210 DECAL-THIS MACHINE IS PROTECTED WITH QUINSYN IV

* Use appropriate decal for horsepower (HP) and pressure (psi) of unit.** Use appropriate decal for fluid type used.


DECAL GROUP (water-cooled)


1 1 143194 SHEET-SAFETY DECALS2 1 128198 LABEL-GENUINE QUINCY COMPONENTS3 1 22177 TAG-FLUID TYPE SHIPPED WITH UNIT4 1 110690-001 ENVELOPE-PLASTIC5* 1 142247-75A DECAL-QSF 75, 100 PSI

1 142247-75B DECAL-QSF 75, 125 PSI1 142247-75C DECAL-QSF 75, 150 PSI1 142247-10A DECAL-QSF 100, 100 PSI1 142247-10B DECAL-QSF 100, 125 PSI1 142247-10C DECAL-QSF 100, 150 PSI

6 1 142325 DECAL-FLUID LEVEL7** 1 128425 DECAL-THIS MACHINE IS PROTECTED WITH QUINSYN

1 128426 DECAL-THIS MACHINE IS PROTECTED WITH QUINSYN-F1 142210 DECAL-THIS MACHINE IS PROTECTED WITH QUINSYN IV

* Use appropriate decal for horsepower (HP) and pressure (psi) of unit.** Use appropriate decal for fluid type used.


CONTROL SCHEMATIC (75 HP)(less differential pressure switches)143383-11


CONTROL SCHEMATIC (75 HP)(with differential pressure switches)

143383-12


CONTROL SCHEMATIC (100 HP, across the line)(less differential pressure switches)143383-21


CONTROL SCHEMATIC (100 HP, across the line)(with differential pressure switches)

143383-22


CONTROL SCHEMATIC (100 HP, wye-delta)

143383-23


ELECTRICAL CONTROL DIAGRAM (across the line)(less differential pressure switches)

WP2001A1


ELECTRICAL CONTROL DIAGRAM (across the line)(with differential pressure switches)WP2001A


ELECTRICAL CONTROL DIAGRAM(wye-delta)

WP2001B


MAINTENANCE KITS

PARTQTY. NUMBER DESCRIPTION

QuinSyn PG™

1 KQSF02H-01PG MAINTENANCE KIT (75 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-003 SEPARATOR-AIR/FLUID, PRIMARY 3 143808-005 FLUID-QUINSYN PG (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

1 KQSF03H-01PG MAINTENANCE KIT (100 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-018 SEPARATOR-AIR/FLUID, PRIMARY 3 143808-005 FLUID-QUINSYN PG (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

QuinSyn Plus™

1 KQSF02H-01QP MAINTENANCE KIT (75 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-003 SEPARATOR-AIR/FLUID, PRIMARY 3 144046-005 FLUID-QUINSYN PLUS (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

1 KQSF03H-01QP MAINTENANCE KIT (100 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-018 SEPARATOR-AIR/FLUID, PRIMARY 3 144046-005 FLUID-QUINSYN PLUS (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS


MAINTENANCE KITS


Quinsyn®

1 KQSF02H-01QS MAINTENANCE KIT (75 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-003 SEPARATOR-AIR/FLUID, PRIMARY 3 127462-005 FLUID-QUINSYN (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

1 KQSF03H-01QS MAINTENANCE KIT (100 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-018 SEPARATOR-AIR/FLUID, PRIMARY 3 127462-005 FLUID-QUINSYN (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

Quinsyn-F® (food grade)

1 KQSF02H-01QF MAINTENANCE KIT (75 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-003 SEPARATOR-AIR/FLUID, PRIMARY 6 110756-005 FLUID-QUINSYN F (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

1 KQSF03H-01QF MAINTENANCE KIT (100 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-018 SEPARATOR-AIR/FLUID, PRIMARY 6 110756-005 FLUID-QUINSYN F (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS



MAINTENANCE KITS

QuinSyn IV

1 KQSF02H-01Q4 MAINTENANCE KIT (75 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-003 SEPARATOR-AIR/FLUID, PRIMARY 6 141140-005 FLUID-QUINSYN IV (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

1 KQSF03H-01Q4 MAINTENANCE KIT (100 HP)includes:

6 142243 ELEMENT-FLUID FILTER 2 23458-4 ELEMENT-AIR FILTER 1 124487-018 SEPARATOR-AIR/FLUID, PRIMARY 6 141140-005 FLUID-QUINSYN IV (5 gallons) 2 128515-3 KIT-FLUID ANALYSIS

Recommended Spare Parts

1 143084 KIT-SHAFT SEAL2 122880-222 SWITCH-TEMPERATURE1 20775 KIT-DIFFERENTIAL PILOT VALVE 1 129732-050 KIT-LINE FILTER1 128691-052 KIT-MINIMUM PRESSURE CHECK VALVE

*1 124487-003 SEPARATOR (75 HP)*1 124487-018 SEPARATOR (100 HP)*1 142243 ELEMENT-FLUID FILTER*1 23458-4 ELEMENT-AIR FILTER*3 143808-005 FLUID-QUINSYN PG (5 gallons)*2 128515-3 KIT-FLUID ANALYSIS

* These items are included in the maintenance kits.

Notes

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Quincy Compressor® - QSF™ 75 & 100 HP

June 30, 2003 Page 1 of 2

QUINCY COMPRESSOR AND ORTMAN FLUID POWER DIVISIONS

STANDARD TERMS AND CONDITIONS

LEGAL EFFECT: Except as expressly otherwise agreed to in writing by an authorized representative of Seller, the following terms and conditions shall apply to and form a part of this order and any additional and/or different terms of Buyer’s purchase order or other form of acceptance are rejected in advance and shall not become a part of this order. The rights of Buyer hereunder shall be neither assignable nor transferable except with the written consent of Seller. This order may not be canceled or altered except with the written consent of Seller and upon terms which will indemnify Seller against all loss occasioned thereby. All additional costs incurred by Seller due to changes in design or specifications, modification of this order or revision of product must be paid for by Buyer. In addition to the rights and remedies conferred upon Seller by this order, Seller shall have all rights and remedies conferred at law and in equity and shall not be required to proceed with the performance of this order if Buyer is in default in the performance of such order or of any other contract or order with seller. TERMS OF PAYMENT: Unless otherwise specified in the order acknowledgment, the terms of payment shall be net cash within thirty (30) days after shipment. These terms shall apply to partial as well as complete shipments. If any proceeding be initiated by or against Buyer under any bankruptcy or insolvency law, or in the judgment of Seller the financial condition of Buyer, at the time the equipment is ready for shipment, does not justify the terms of payment specified, Seller reserves the right to require full payment in cash prior to making shipment. If such payment is not received within fifteen (15) days after notification of readiness for shipment, Seller may cancel the order as to any unshipped item and require payment of its reasonable cancellation charges. If Buyer delays shipment, payments based on date of shipment shall become due as of the date when ready for shipment. If Buyer delays completion of manufacture, Seller may elect to require payment according to percentage of completion. Equipment held for Buyer shall be at Buyer’s risk and storage charges may be applied at the discretion of Seller. Accounts past due shall bare interest at the highest rate lawful to contract for but if there is no limit set by law, such interest shall be eighteen percent (18%). Buyer shall pay all cost and expenses, including reasonable attorney’s fees, incurred in collecting the same, and no claim, except claims within Seller’s warranty of material or workmanship, as stated below, will be recognized unless delivered in writing to Seller within thirty (30) days after date of shipment. TAXES: All prices exclude present and future sales, use, occupation, license, excise, and other taxes in respect of manufacture, sales or delivery, all of which shall be paid by Buyer unless included in the purchase price at the proper rate or a proper exemption certificate is furnished. ACCEPTANCE: All offers to purchase, quotations and contracts of sales are subject to final acceptance by an authorized representative at Seller’s plant. DELIVERY: Except as otherwise specified in this quotation, delivery will be F. O. B. point of shipment. In the absence of exact shipping instruction, Seller will use its discretion regarding best means of insured shipment. No liability will be accepted by Seller for so doing. All transportation charges are at Buyer’s expense. Time of delivery is an estimate only and is based upon the receipt of all information and necessary approvals. The shipping schedule shall not be construed to limit seller in making commitments for materials or in fabricating articles under this order in accordance with Seller’s normal and reasonable production schedules. Seller shall in no event be liable for delays caused by fires, acts of God, strikes, labor difficulties, acts of governmental or military authorities, delays in transportation or procuring materials, or causes of any kind beyond Seller’s control. No provision for liquidated damages for any cause shall apply under this order. Buyer shall accept delivery within thirty (30) days after receipt of notification of readiness for shipment. Claims for shortages will be deemed to have been waived if not made in writing within ten (10) days after the receipt of the material in respect of which any such shortage is claimed. Seller is not responsible for loss or damage in transit after having

June 30, 2003 Page 2 of 2

received “In Good Order” receipt from the carrier. All claims for loss or damage in transit should be made to the carrier. TITLE & LIEN RIGHTS: The equipment shall remain personal property, regardless of how affixed to any realty or structure. Until the price (including any notes given therefore) of the equipment has been fully paid in cash, Seller shall, in the event of Buyer’s default, have the right to repossess such equipment. PATENT INFRINGMENT: If properly notified and given an opportunity to do so with friendly assistance, Seller will defend Buyer and the ultimate user of the equipment from any actual or alleged infringement of any published United States patent by the equipment or any part thereof furnished pursuant hereto (other than parts of special design, construction, or manufacture specified by and originating with Buyer), and will pay all damages and costs awarded by competent court in any suit thus defended or of which it may have had notice and opportunity to defend as aforesaid. STANDARD WARRANTY: Seller warrants that products of its own manufacture will be free from defects in workmanship and materials under normal use and service for the period specified in the product instruction manual. Warranty for service parts will be ninety (90) days from date of factory shipment. Electric Motors, gasoline and diesel engines, electrical apparatus and all other accessories, components and parts not manufactured by Seller are warranted only to the extent of the original manufacturer’s warranty.

Notice of the alleged defect must be given to the Seller, in writing with all identifying details including serial number, type of equipment and date of purchase within thirty (30) days of the discovery of the same during the warranty period. Seller’s sole obligation on this warranty shall be, at its option, to repair or replace or refund the purchase price of any product or part thereof which proves to be defective. If requested by Seller, such product or part thereof must be promptly returned to seller, freight prepaid, for inspection. Seller warrants repaired or replaced parts of its own manufacture against defects in materials and workmanship under normal use and service for ninety (90) days or for the remainder of the warranty on the product being repaired. This warranty shall not apply and Seller shall not be responsible or liable for:

(a) Consequential, collateral or special losses or damages; (b) Equipment conditions caused by fair wear and tear, abnormal conditions of use, accident, neglect or

misuse of equipment, improper storage or damage resulting during shipping;

(c) Deviation from operating instructions, specifications or other special terms of sale;

(d) Labor charges, loss or damage resulting from improper operation, maintenance or repairs made by person(s) other than Seller or Seller’s authorized service station.

In no event shall Seller be liable for any claims whether arising from breach of contract or warranty or claims of negligence or negligent manufacture in excess of the purchase price. THIS WARRANTY IS THE SOLE WARRANTY OF SELLERS AND ANY OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED IN LAW OR IMPLIED IN FACT, INCLUDING ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE ARE HEREBY SPECIFICALLY EXCLUDED. LIABILITY LIMITATIONS: Under no circumstances shall the Seller have any liability for liquidated damages or for collateral, consequential or special damages or for loss of profits, or for actual losses or for loss of production or progress of construction, whether resulting from delays in delivery or performance, breach of warranty, negligent manufacture or otherwise. ENVIROMENTAL AND OSHA REQUIREMENTS: At the time of shipment of the equipment from the factory, Quincy Compressor / Ortman Fluid Power will comply with the various Federal, State and local laws and regulations concerning occupational health and safety and pollution. However, in the installation and operation of the equipment and other matters over which the seller has no control, the Seller assumes no responsibility for compliance with those laws and regulations, whether by the way of indemnity, warranty or otherwise.

QSF 75-100 ( Manual de Compresores )

Documents

Transcript of QSF 75-100 ( Manual de Compresores )