16D5292-0072No.

Central Mechanical Inc3774 Puritan Way Erie CO 80516

TO:

01/05/2016DATE:

230000-HVACRE:

Ryan HadawayATTN:

Shop Drawings

Letter

Prints

Change Order

Plans

Samples

Specifications / Product Data

Other:

Approval

Your Use

As Requested

Review and Comment

Attached

Separate Cover Via:

Approved as Submitted

Approved as Noted

Returned After Loan

Resubmit

Submit

Returned

Returned for Corrections

Due Date: 01/05/2016

WE ARE SENDING: SUBMITTED FOR:

SENT VIA:

ACTION TAKEN:

TRANSMITTAL

James GettmanSigned:

PROJECT: ACSD50-Flynn Elementary HVAC Upgrade & Addition

01/05/2016

Date

232100.01

Code

HVAC Hydronic Systems

Description

Revise andResubmit

Status

JOB: 16D5292

CC:

Item

Submittal 230000

Package

1

Rev. Copies

Ph/Fax: 303-833-2271 303-833-2625

NOTES: resubmit on items with notes 1,3 and 4 only.

5995 Greenwood Plaza Blvd.Suite 100Greenwood Village, CO 80111-4710303-571-5377303-629-7467 (fax)

SUBMITTAL REVIEW

Q:\15\15076\Construction\Submittals\HVAC\Hydronic Systems\15-12-29, reviewed hydronic systems.doc

Lakewood: 2525 South Wadsworth Blvd., Suite 200 Lakewood, CO 80227 P: 303-988-4514 F: 303-988-4517 Fort Collins: 4730 South College Ave., Suite 203 Fort Collins, CO 80525 P: 970-568-8762 F: 303-988-4517

www.TheBallardGroup.com

To: DAO Architecture

3843 W. 73rd

Avenue

Westminster, CO 80030

Date: 12-29-15

TBG Project No: 15076.00

Attention: Tom Rafferty / Dan Orecchio

Project: ACSD #50 – Flynn Elementary School

We are transmitting the following shop drawings with comments listed below.

NET: No Exceptions Taken MCN: Make Corrections Noted RX: Rejected

RR: Revise and Resubmit SSI: Submit Specified Item

CMT: See Comment Below

Copies Item Manufacturer NET MCN RR RX SSI CMT

PDF Manual Air Vent Valves Bell & Gossett X

PDF Automatic Air Vent Valves Bell & Gossett X

PDF Air Separator AS-1 Wessels X X 1

PDF Expansion Tank ET-1 Amtrol X

PDF Pump Suction Diffuser Bell & Gossett X 2

PDF Pressure Relief Valve Watts X

PDF Pumps P-1 & P-2 Taco X X 3

PDF Pumps P-3 & P-4 Bell & Gossett X

PDF Pump P-5 Bell & Gossett X

PDF Inhibited Propylene Glycol Huntsmen X X 4

PDF Glycol Feeder GF-1 Sage X

PDF Pre-Startup Cleaner PreClean X

PDF Bypass Chemical Pot Feeder Wingert X 5,6

Comments:

1. Provide approved manufacturer.

2. Provide adjustable support foot, either from the manufacturer or field fabricated.

3. Pump P-1 shall be capable of flowing 90 GPM at 20 ft of head, while pump P-2 shall be

capable of flowing 60 GPM at 20 ft of head.

4. Provide “uninhibited” propylene glycol as provided by “Industrial Chemical

Corporation” as this is the District’s standard.

5. Provide Bypass Chemical Pot Feeder with ¾” NPT female drain pipe connection.

6. Bypass Chemical Pot Feeder shall have a continuous threaded closure requiring 2 ½

turns, as opposed to ¼ turn closure.

Signed: Don Beaglehole

Submittal Cover Sheet

Project Name Flynn ES

Project Number 16D5292

Date 12-21-15

Architect DAO Architecture

Contractor GH Phipps Construction Companies

Prepared by/Subcontractor Central Mechanical

Supplier

Manufacturer

Submittal Number 232100.01 HVAC Hydronic Systems

Specification Section 232100

Drawing Number/Location

Contractor Review

A/E Review:

Contractor Notes:

MANUAL AIR VENT VALVE

A-310

Air Vents

A full line of manual and automatic air vents designed to remove troublesome air in the system.

• Available in 1/8”, 1/2” and 3/4” connections

• Cast iron, brass and steel construction with

non-ferrous internals

Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries.© 2012 Xylem Inc. A-310 May 2006

Xylem Inc.

8200 N. Austin Avenue Morton Grove, Illinois 60053 Phone: (847) 966-3700 Fax: (847) 965-8379www.xyleminc.com/brands/bellgossett

AUTOMATIC AIR VENT VALVE

SUBMITTALHS-103(C)

JOB: Flynn Elementary HVAC Upgrade REPRESENTATIVE: McNevin Co

UNIT TAG: ORDER NO. DATE: 11/13/2015ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:

Hoffman SpecialtyModel 792High PressureWater MainVent Valve

Materials of Construction

Part Specifications

Body Cast Iron

Cover Cast Iron

Float Stainless Steel

Seat Stainless Steel

Pin Stainless Steel

Capacities

Water Pressure psig (bar)

Air Discharge to Atmospherecu. ft./min.(S(m³/min))

100(6.9)

10(.28)

150(10.3)

15(.42)

200(13.8)

20(.57)

250(17.3)

25(.70)

RATINGS

Model

NPT Bottom Inlet Sizein.

NPT Side Inlet Sizein.

NPT Outlet Sizein.

Maximum Operating Pressurepsig (bar)

Maximum Hydrostatic

Pressurepsig (bar)

Maximum Operating Temperature

ºF (ºC)792 3/4 1/2 1/2 250 (17.3) 350 (24.2) 300 (149)

SCHEDULEMODEL

NUMBERPART

NUMBER TAGGING INFORMATION QTY.

792 401494 1

Xylem Inc.8200 N. Austin AvenueMorton Grove, IL 60053Phone (847)966-3700Facsimile (847)966-9052www.hoffmanspecialty.com

AS-1 AIR SEPARATOR

SUBMITTAL SPA-SERIES AIR SEPARATOR

Models: SPA-2 thru SPA-24 Submittal Sheet No. D-1003A Date: 7/13

Job Name ______________________________ Submitted By _______________ Date ________

Location ______________________________ Approved By _______________ Date ________

______________________________ Order No. _______________ Date ________

Engineer ______________________________ Notes __________________________________

Contractor ______________________________ __________________________________

Sales Rep. ______________________________ __________________________________

101 TANK ST ● GREENWOOD, IN 46143 ● (317) 888-9800 ● (317) 888-9988 FAX ● www.westank.com

Typical Specification Furnish and install, as shown on plans, a vortex type air separator model SPA __________ sized for ___________GPM, with __________” (NPT/Flanged) tangential connections, as manufactured by Wessels Company. A blowdown connection shall be provided to facilitate routine cleaning of the unit. The tank must be constructed in accordance with most recent addendum of Section VIII Division 1 of the ASME Boiler and Pressure Vessel Code, and shall be constructed and stamped for 125 PSI working pressure @ 450°F.

Each air separator shall be Wessels model number SPA-______________ or approved equal.

Description Wessels SPA ASME Vortex type Air Separators eliminate air quickly and efficiently from open and closed loop heating/cooling systems. Water enters and exits through unique “tangential” connections, which promote a low velocity swirling effect in the center of the unit. Natural centrifugal forces allow the heavier air-free water to move toward the outer edges while entrained air is captured within the “eye” of the vortex and released out of the top of the separator. The bubble-free water then exits near the bottom of the unit, protecting the systems against the noise, corrosion, and damage commonly caused by entrained air.

Construction Shell: Carbon Steel Heads: Carbon Steel Exterior: Primer Painted

Performance Limitations Maximum Design Temperature: 450°F Maximum Design Pressure: 125 PSIG*

*200 & 250 PSIG available

SPA-2 72006019 56SPA-2.5 72006025 90SPA-3 72006030 190SPA-4 72006035 300SPA-5 72016036 530SPA-6 72001060 850SPA-8 72016080 1900SPA-10 72030010 3200SPA-12 72030012 4800SPA-14 72072014 6100SPA-16 72072016 8000SPA-18 72072018 9700SPA-20 72072020 12000SPA-22 72072022 15000SPA-24 72072024 17000

Model Number

Part Number

Max Flow (GPM) Tagging Information Quantity

Flynn Elementary HVAC Upgrade

Central Mechanical

McNevin Company

Ferguson 11/13/15

33

3

AS-1 1

D-1003A 7/13

101 TANK ST ● GREENWOOD, IN 46143 ● (317) 888-9800 ● (317) 888-9988 FAX ● www.westank.com

Notes Available with mounting clips.

Dimensions & Weights

SPA-2 thru SPA-24

SPA-2 2 NPT 34SPA-2.5 2.5 NPT 37SPA-3 3 25 6 1/4 8 19 3/4 45SPA-4 4 80SPA-5 5 125SPA-6 6 175SPA-8 8 210SPA-10 10 460SPA-12 12 577SPA-14 14 36 78 22 31 1/2 46 3/8 30 850SPA-16 16 48 108 30 40 60 38 1858SPA-18 18 54 124 33 50 66 44 2490SPA-20 20 60 138 35 60 72 50 3346SPA-22 22 66 78 3879SPA-24 24 66 80 4211

Model Number A B C

Approx. Shipping Wt (lbs)D E F G

Dimensions in InchesConnection

Size

24

12

14

20

30

32

44

60 1/2

22 1/2 5 1/2

150

9 1/8

13 1/4

19

38 56

1 1/4

1 1/2

2

66

16 5/8

21 3/4

28

41

8 1/2

10 3/4

14 1/2

20

9 1/2

11 1/2

18

ET-1 EXPANSION TANK

MC 4400 (06/15)Amtrol Inc., 1400 Division Road, West Warwick, RI 02893 USA T: 401.884.6300 www.amtrol.com50

B

A

AX-120V THROUGH AX-240V

ConstructionShell ASME Approved SteelDiaphragm Heavy Duty Butyl/EPDM

System ConnectionNPTF1 Malleable Iron CenterNPTF2 Malleable Iron BottomNPTM3 Malleable Iron Top Offset

Finish Red Oxide PrimerAir Valve Schrader Valve w/EPDM SeatsFactory Precharge 12 PSIG (.8 bar)

PerformanceMaximum Operating Temperature 240°F (115°C)Maximum Working Pressure 125 PSIG (8.6 bar)Warranty 1 Year

125 PSIG Working Pressure

EXTROL®

Hydronic Expansion Tanks: Vertical AX Series ASME

Vertical ASME ModelsModel

Number

TankVolume

Max.Accept. Volume

ATank Diameter

BTank Height

Sys. Conn

ShippingWeight

Gal Lit Gal Lit In mm In mm In Lbs Kg

AX-15V 8.0 30.3 2.4 9.1 12 305 20 508 ½1 39 18

AX-20V 10.9 41.3 2.4 9.1 12 305 27 686 ½1 47 21

AX-40V 21.7 82.2 11.3 42.8 16 356 30 762 ½1 76 34

AX-60V 33.6 127.2 11.3 42.8 16 356 45 1143 ½1 98 44

AX-80V 44.4 168.1 22.6 85.5 24 610 29 737 11 155 70

AX-100V 55.7 211.8 22.6 85.5 24 610 34 864 11 176 80

AX-120V 68.0 257.4 34.0 128.7 24 610 47 1194 12 214 97

AX-144V 77.0 291.5 34.0 128.7 24 610 52 1321 12 230 104

AX-180V 90.0 340.7 34.0 128.7 24 610 60 1524 12 271 123

AX-200V 110.0 416.4 34.0 128.7 24 610 66 1676 12 290 132

AX-240V 132.0 500.0 46.0 174.0 30 762 58 1473 12 401 182

AX-260V 159.0 600.0 56.0 212.0 30 762 65 1651 1¼3 460 209

AX-280V 211.0 800.0 84.0 318.0 30 762 82 2083 1¼3 590 268

All dimensions and weights are approximate.

B

A

AX-15V THROUGH AX-100V

B

A

AX-260V THROUGH AX-280V

120°

F

E

HOLE SIZE "G"ON

BOLT CIRCLE "D"

BOTTOM VIEW

Optional Seismic RestraintsTank

DiameterBolt

Circle Dim. Dim. HoleSize

B D E F G12 12¾ 2 2 9⁄16

16¼ 14¾ 2 2 9⁄16

24 18 2 2 9⁄16

30 27 3 3 ¾

Job Name _____________________________________

Engineer _____________________________________

Contractor _____________________________________

P.O. No. _____________________________________

Sales Rep. _____________________________________

Model No. _____________________________________

Notes _________________________________

_______________________________________

_______________________________________

_______________________________________

_______________________________________

_______________________________________

Application• For use in closed, non-potable

hydronic heating and chilled water systems.

• Designed to meet all ASMECode Section VIII, Division 1 standards.

• Available with optional sightglass and seismic restraints.

PUMPS P-3 & P-4 SUCTION DIFFUSERS

SUBMITTAL

B-826JOB: Flynn Elementary HVAC Upgrade REPRESENTATIVE: McNevin Co

UNIT TAG: ORDER NO. DATE: 11/13/2015ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:

B&G Suction Diffuser PlusCentrifugal Pump Accessories

DESCRIPTIONThe Bell & Gossett Suction Diffuser Plus is designed for direct application to the pump suction and provides ideal flow conditions for the pump, providing NPSH requirements are met. Its integrated Flow Cone directs flow through the unit and into the pump suction while working with the full length straightening vanes to create a more uniform flow profile. The orifice cylinder has a free area equal to five times the cross section of the pump suction opening and serves as a coarse strainer to protect the pump from large sediment. The disposable start-up strainer helps to clean the system during the first 24-48 hours of operation before it is removed. Its optional pressure temperature ports allow you to verify that the start-up strainer has been removed without the need to take the unit apart. OPERATING DATAOperating Temperature: 250?F (121?C)Working Pressure: 175 psi (1,207 kPa)

MATERIALS OF CONSTRUCTION

Type Body Inlet VanesOrifice

CylinderStart-UpStrainer

X Cast Iron Steel 16 Mesh Bronze

Z Cast Iron Stainless Steel 16 Mesh Bronze

NOTES: Type X-For Closed Systems.Type Z-For Domestic Water and Tower Systems.

SCHEDULEMODEL

NUMBERDIMENSIONS INCHES (mm)

TAGGING INFORMATIONX

QUANTITYZ

QUANTITYSYSTEM SIDE PUMP SIDEBA-3X/BA-3Z 2 (50.8) FPT 1-1/2 (38.1) FPTBB-3X/BB-3Z 2 (50.8) FPT 2 (50.8) FPTCB-3X/CB-3Z 2-1/2 (63.5) FPT 2 (50.8) FPTCC-3X/CC-3Z 2-1/2 (63.5) FLG 2-1/2 (63.5) FLGDA-3X/DA-3Z 3 (76.2) FPT 1-1/2 (38.1) FPTDB-3X/DB-3Z 3 (76.2) FPT 2 (50.8) FPT

DC-3X/DC-3Z

3 (76.2) FLG 2-1/2 (63.5) FLG P-3&4 2

DD-3X/DD-3Z 3 (76.2) FLG 3 (76.2) FLGEC-3X/EC-3Z 4 (101.6) FLG 2-1/2 (63.5) FLGED-3X/ED-3Z 4 (101.6) FLG 3 (76.2) FLGEE-3X/EE-3Z 4 (101.6) FLG 4 (101.6) FLGFE-3X/FE-3Z 5 (127) FLG 4 (101.6) FLGFF-3X/FF-3Z 5 (127) FLG 5 (127) FLGGE-3X/GE-3Z 6 (152.4) FLG 4 (101.6) FLGGF-3X/GF-3Z 6 (152.4) FLG 5 (127) FLGGG-3X/GG-3Z 6 (152.4) FLG 6 (152.4) FLGHG-3X/HG-3Z 8 (203.2) FLG 6 (152.4) FLGHH-3X/HH-3Z 8 (203.2) FLG 8 (203.2) FLGJH-3X/JH-3Z 10 (254) FLG 8 (203.2) FLGJJ-3X/JJ-3Z 10 (254) FLG 10 (254) FLG

SUCTION DIFFUSER PLUS B-826

DIMENSIONS − INCHES (mm)

Model No. System Side Pump Side A B C D E F G H JOrifice Cylinder Free

Area in2 (cm2)Approx. Shpg.Wt. Lbs. (Kg)

BA-3 2(50.8) T 1-1/2

(38.1) T 5.96(151)

3(76)

2.25(57)

2.37(60)

3/4(19)

3.81(97)

5.25(133)

5.15(130.8) N/A 11

(71)13(6)

BB-3 2(50.8) T 2

(50.8) T 7.56(192)

3.87(98)

2.75(70)

2.75(70)

3/4(19)

4.38(111)

5.75(146)

6.75(171.5) N/A 20-1/2

(132)14(6)

CB-3 2-1/2(63.5) T 2

(63.5) T 7.56(192)

3.87(98)

2.75(70)

2.75(70)

3/4(19)

4.38(111)

5.75(146)

6.75(171.5) N/A 20-1/2

(132)16(7)

CC-3 2-1/2(63.5) F 2-1/2

(63.5) F 8.44(214)

4.75(121)

4.75(121)

3.5(89)

3/4(19)

5.77(147) N/A 7.63

(193.7)3.5(89)

26(168)

36(16)

DA-3 3(76.2) T 1-1/2

(38.1) T 7.44(189)

3.87(98)

2.75(70)

2.75(70)

3/4(19)

4.38(111)

5.75(146)

6.63(168.3) N/A 20-1/2

(132)17(8)

DB-3 3(76.2) T 2

(50.8) T 7.56(192)

3.87(98)

2.75(70)

2.75(70)

3/4(19)

4.38(111)

5.75(146)

6.75(171.5) N/A 20-1/2

(132)17(8)

DC-33

(76.2) F 2-1/2(63.5) F 8.75

(222)5

(127)5

(127)3.50(89)

3/4(19)

5.77(147) N/A 7.63

(193.7)3.75(95)

26(168)

44(20)

DD-3 3(76.2) F 3

(76.2) F 9.56(243)

5.50(140)

5.50(140)

3.75(95)

3/4(19)

7.0(178) N/A 8.75

(222.3)3.75(95)

37-1/2(242)

48(22)

EC-3 4(101.6) F 2-1/2

(63.5) F 11(279)

6.50(165)

6.50(165)

3.50(95)

3/4(19)

5.77(147) N/A 7.63

(193.7)4.50(114)

26(168)

42(19)

ED-3 4(101.6) F 3

(76.2) F 11(279.4)

6.50(165)

6.50(165)

3.75(95)

3/4(19)

7.93(201) N/A 10

(254)4.5

(114)37-1/2(242)

55(25)

EE-3 4(101.6) F 4

(101.6) F 11.5(292)

6.50(165)

6.50(165)

4.50(114)

3/4(19)

7.87(200) N/A 10.69

(271.5)4.50(114)

65(419)

72(33)

FE-3 5(127) F 4

(101.6) F 12.5(318)

7.50(191)

7.50(191)

4.50(114)

3/4(19)

7.87(200) N/A 10.69

(271.5)5

(127)65

(419)84

(38)

FF-3 5(127) F 5

(127) F 13.67(347)

7.50(191)

7.50(191)

5(127)

3/4(19)

10.44(265) N/A 12.84

(326.1)5

(127)90

(581)100(45)

GE-3 6(152.4) F 4

(101.6) F 13.5(343)

8(203)

8(203)

4.50(114)

3/4(19)

7.87(200) N/A 10.69

(271.5)5.50(140)

65(419)

90(41)

GF-3 6(152.4) F 5

(127) F 15.67(398)

8(203)

8(203)

5(127)

3/4(19)

10.46(266) N/A 13.84

(351.5)5.50(140)

90(581)

105(48)

GG-3 6(152.4) F 6

(152.4) F 15.82(402)

8(203)

8(203)

5.50(140)

3/4(19)

11(279) N/A 14.75

(374.7)5.50(140)

127(819)

134(61)

HG-3 8(203.2) F 6

(152.4) F 15.82(402)

9(229)

9(229)

5.50(140)

3/4(19)

11(279) N/A 14.75

(374.7)6.75(171)

127(819)

150(68)

HH-3 8(203.2) F 8

(203.2) F 19.55(497)

9(229)

9(229)

6.75(171)

3/4(19)

12.62(321) N/A 18.25

(463.6)6.75(171)

218(1406)

250(113)

JH-3 10(254) F 8

(203.2) F 19.55(497)

10(254)

11(279)

6.75(171)

3/4(19)

12.62(321) N/A 18.25

(463.6)8

(203)218

(1406)290

(132)

JJ-3 10(254) F 10

(254) F 22.80(579)

11(279)

11(279)

8(203)

3/4(19)

15.68(398) N/A 21.50

(546.1)8

(203)338

(2180)415

(188)(T) Threaded - FPT (F) Flanged *Dimensions include orifice cylinder + 2-1/2 (64) inch clearance.Dimensions are subject to change. Not to be used for construction purposes unless certified.

SUCTION DIFFUSER PLUS B-826

TYPICAL SPECIFICATIONSProvide with each pump a Bell & Gossett Suction Diffuser Plus of the size noted on drawings.Units shall consist of angle type body, flanged system connection, integrated Flow Cone, carbon/stainless steel straightening vane and combination diffuser-strainer-orifice cylinder with 3/16" diameter openings for pump protection. The unit shall include a disposable fine mesh strainer which shall be removed after system start-up. Unit shall have pressure/temperature ports at the suction and discharge to allow for measurement of differential pressure across the unit.

Orifice cylinder shall be designed to withstand pressure differential equal to pump shut-off head (maximum ______ PSI) and shall have a free area equal to five times cross section area of pump suction opening. Vane length shall be no less than 2-1/2 times the pump connection diameter. Unit shall be provided with adjustable support foot to carry the weight of suction piping. Unit shall be rated for 175 psi (1,207kPa) maximum working pressure and 250F (121C) macimum working temperature.

RELIEF VALVES

For Pressure Protection of Hot Water Heating Boilers

Sizes: 3⁄4" – 2" (20 - 50mm)

Series 174ABronze body safety relief valves for pressure protection only of all types of hot water heating boiler equipment. Pressure range 30 to 150psi (2.1 - 10 bar) with corresponding high rat-ings from 650,000 to 14,370,000 BTU/hr. Female inlet and outlet connections. Sizes 3⁄4" - 2" (20 - 50mm).

Series 374AIron body with forged brass inlet, 550,000 BTU/hr rating. 3⁄4" (20mm) only.

Series 740Iron body with expanded outlets for hot water space heating boilers. Pressure range 30 to 75psi (2 to 5 bar) with corre-sponding high ratings from 925,000 to 10,700,000 BTU/hr.

Features• Seatlocatedabovedrain;watercan’tbetrappedand

sedimentcan’tfoulseat.• Non-mechanicalseat-to-discalignmentwillnotstick

or freeze.• Watersealofhightemperatureresistingmaterialisolatesspring

workingpartsfromwaterduringrelief.

SpecificationsBoiler Relief ValvesAn ASME Section IV certified pressure relief valve shall be installed on each boiler as noted. The valve shall have a BTU ratinginexcessoftheBTUratingoftheboiler’sheatingoutput.Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler workingpressure.Thevalveshallfeaturearaisedseatandnon-mechanicaldiscalignment.Workingpartsandspringshallbe isolated from any discharge by a high temperature resistant material.ValveshallbeaWattsSeries174A,374Aor740.

OperationAs thermal expansion conditions develop, pressure builds up to the setting of the relief valve. This will cause discharging of small quantity of water.

Should operating controls fail, permitting runaway firing, the boiler water may reach steam temperatures. The valve will then open to discharge steam at the rate or faster than the boiler can generate it, thus restoring system pressure to a safer level.

NOTICEThe discharge line must be the same size as the valve outlet, and must pitch downward from the valve to a safe place for disposal.

Valve lever must be tripped at least once a year to ensure that waterways are clear. This device is designed for emergency safety relief and shall not be used as an operating control.

For Hot Water Boiler ApplicationsES-174A-740

Series 174A Series 740

Series 174A, 374, 740ASME Water Pressure Relief Valves

JobName ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––

Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––

Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’sP.O.No. ––––––––––––––––––––––––––––––––––

Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––

Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.

It is illegal to use this product in any plumbing system providing waterforhumanconsumption,suchasdrinkingordishwashing,in the United States. Before installing standard material product, consult your local water authority, building and plumbing codes.

WARNING!The information contained herein is not intended to replace the full product installation and safety information available or the experience of a trained product installer. You are required to thoroughly read all installation instructions and product safety information before begin-ning the installation of this product.

NOTICE

Materials

Series 174A• Bronzebodyconstruction

• Nonmetallicdisc-to-metalseating

Series 740• Ironbodyconstruction

• Nonmetallicdisc-to-metalseating

Pressure – Temperature

Series 174APressure range: 30psi to 150psi (2 to 10 bar) with correspond-ing high BTU/hr ratings from 650,000 to 14,370,000 BTU/hr. Maximum Temperature: 250 ºF (121 ºC)

Series. 374APressure range: rated up to 550,000 BTU/hr at a 30psi (2 bar) setting.(Othersettingsavailable)

Series 740Pressure range: 30psi to 75psi (2 to 5 bar) with corre-sponding high ratings from 925,000 to 10,700,000 BTU/hr. Maximum Temperature: 250 ºF (121 ºC)

Standards

TestedandratedbytheNationalBoardofBoilerandPressureVessel Inspectors to the requirements of ASME. Meets Military Spec. MIL-V-18634B, Type I, Class 3A, Style A (Bronze Body), Style B (Iron Body).

ASME

Dimensions – Weights

Capacity*BTU/hr Steam Pressure Discharge CapacitiesAs tested and rated by the National Board of Boiler and Pressure Vessel Inspectors

SerieS 174A

Size (Dn) Height Length Weight

Model in. mm Model in. mm in mm lbs. kg.374A 3⁄4 x 3⁄4 20 x 20 – 31⁄2 90 21⁄2 64 1.2 0.5

174A 3⁄4 x 3⁄4 20 x 20 M3 41⁄2 116 23⁄4 67 1.2 0.5

174A 1 x 1 25 x 25 M1 53⁄4 144 3 76 1.9 0.9

174A 11⁄4 x 11⁄4 32 x 32 M1 81⁄2 213 41⁄4 109 4.6 2.1

174A 11⁄2 x 11⁄2 40 x 40 M 91⁄4 232 43⁄4 122 6.9 3.1

174A 2 x 2 50 x 50 M 111⁄2 290 61⁄2 162 14.4 6.5

SerieS 740

740 3⁄4 x 1 20 x 25 M1 55⁄8 143 3 76 1.88 9

740 1 x 11⁄4 25 x 32 M 71⁄4 184 31⁄2 89 3.13 1.4

740 11⁄4 x 11⁄2 32 x 40 M 83⁄4 222 45⁄8 117 6.13 2.8

740 11⁄2 x 2 40 x 50 M 91⁄4 235 51⁄4 133 7.50 3.4

740 2 x 21⁄2 50 x 65 M 115⁄8 295 63⁄4 171 16.50 7.5

SerieS 174A

Set Pressure

3⁄4” x 3⁄4” 1” x 1” 11⁄4” x 11⁄4” 11⁄2” x 11⁄2” 2” x 2”20 x 20mm 25 x 25mm 32 x 32mm 40 x 40mm 50 x 50mm

psi bar Model M3 Model M1 Model M1 Model M Model M30 2.07 650,000 1,005,000 1,682,000 2,020,000 3,815,000

33 2.27 695,000 1,075,000 1,788,000 2,150,000 4,080,000

35 2.41 725,000 1,125,000 1,877,000 2,250,000 4,250,000

36 2.48 740,000 1,145,000 1,916,000 2,310,000 4,344,000

40 2.76 800,000 1,240,000 2,071,000 2,490,000 4,690,000

45 3.1 875,000 1,355,000 2,265,000 2,720,000 5,130,000

50 3.45 950,000 1,470,000 2,459,000 2,950,000 5,575,000

55 3.79 1,025,000 1,590,000 2,653,000 3,190,000 6,010,000

60 4.13 1,100,000 1,702,000 2,847,000 3,425,000 6,450,000

65 4.58 1,170,000 1,820,000 3,041,000 3,660,000 6,890,000

70 4.82 1,245,000 1,935,000 3,325,000 3,890,000 7,330,000

75 5.17 1,320,000 2,055,000 3,429,000 4,125,000 7,770,000

80 5.51 1,400,000 2,166,000 3,605,000 4,360,000 8,215,000

85 5.86 1,470,000 2,285,000 3,817,000 4,590,000 8,650,000

90 6.6 1,545,000 2,400,000 4,011,000 4,825,000 9,090,000

95 6.55 1,620,000 2,520,000 4,205,000 5,060,000 9,530,000

100 6.89 1,695,000 2,635,000 4,399,000 5,290,000 9,970,000

105 7.23 1,770,000 2,750,000 4,593,000 5,525,000 10,410,000

110 7.58 1,845,000 2,865,000 4,787,000 5,760,000 10,850,000

115 7.92 1,920,000 2,980,000 4,981,000 5,990,000 11,290,000

120 8.27 1,995,000 3,100,000 5,175,000 6,225,000 11,730,000

125 8.61 2,070,000 3,215,000 5,370,000 6,460,000 12,170,000

130 8.96 2,145,000 3,330,000 5,564,000 6,690,000 12,610,000

135 9.3 2,220,000 3,445,000 5,758,000 6,925,000 13,050,000

140 9.65 2,295,000 3,565,000 5,952,000 7,160,000 13,490,000

145 9.99 2,370,000 3,680,000 6,146,000 7,390,000 13,390,000

150 10.34 2,445,000 3,795,000 6,340,000 7,630,000 14,370,000

SerieS 740

Set Pressure

3⁄4” x 1” 1” x 11⁄4” 11⁄4” x 11⁄2” 11⁄2” x 2” 2” x 21⁄2”20 x 25mm 25 x 32mm 32 x 40mm 40 x 50mm 50 x 65mm

psi bar Model M1 Model M Model M Model M Model M30 2.07 925,000 1,300,000 2,105,000 2,900,000 5,250,000

33 2.27 989,000 1,390,000 2,250,000 3,100,000 5,613,000

35 2.41 1,032,000 1,450,000 2,345,000 3,235,000 5,855,000

36 2.48 1,053,000 1,480,000 2,395,000 3,300,000 5,975,000

40 2.76 1,139,000 1,600,000 2,590,000 3,569,000 6,461,000

45 3.10 1,245,000 1,750,000 2,830,000 3,903,000 7,067,000

50 3.45 1,352,000 1,899,000 3,075,000 4,237,000 7,672,000

55 3.79 1,459,000 2,049,000 3,315,000 4,572,000 8,277,000

60 4.13 1,566,000 2,200,000 3,560,000 4,907,000 8,883,000

65 4.58 1,672,000 2,349,000 3,800,000 5,241,000 9,488,000

70 4.82 1,779,000 2,499,000 4,045,000 5,575,000 10,093,000

75 5.17 1,886,000 2,649,000 4,285,000 5,909,000 10,700,000

ES-174A-7401442 ©2014Watts

USA:Tel:(978)689-6066•Fax:(978)975-8350•Watts.comCanada: Tel:(905)332-4090•Fax:(905)332-7068•Watts.ca

Latin America: Tel:(52)81-1001-8600•Fax:(52)81-8000-7091•Watts.com

A Watts Water Technologies Company

P-1 & P-2 PUMPS

Submittal Data1600 Series Pumps (Stock Models)

301-001

EFFECTIVE: October 4, 2013 SUPERSEDES: July 1, 2011 1750 RPM MODELS

ITEM NO. MODEL NO. IMPELLER DIA. G.P.M. T.D.H. H.P. ELEC. CHAR.

B (Approximate)

DC

A

TAPPEDHOLE

1/4” NPT

TAPPEDHOLE

1/4” NPT

English dimensions are in inches. Metric dimensions are in millimeters. Metric data is presented in ( ).Do not use for construction purposes unless certified.

NOTE: Individual Submittal Data sheets are available for CUSTOM models.

WEIGHT PUMP/MOTOR

DIMENSIONS: * 1⁄4 HP AVAILABLE IN 1 PHASE ONLY

JOB ENGINEER

CONTRACTOR REP.

MODEL NUMBER FLANGESIZE

POWERHP (KW)

DIMENSIONS

STOCK 1600 CUSTOM 1600 A B C D

1600

1611 11⁄2 (38)

1⁄4 (0.19) *

3 (76)

16.0 (419)

101⁄4 (260) 127⁄8 (327)1610 1⁄3 (0.25) 16.0 (419)1⁄2 (0.37) 17.0 (432)

1615 11⁄2 (38)

1⁄3 (0.25)

31⁄8 (79)

18.0 (457)

131⁄2 (343) 161⁄8 (410)1612 1⁄2 (0.37) 18.5 (470)

1614 3⁄4 (0.56) 19.0 (483)

1 (0.75) 19.5 (495)

1619 2 (51)

3⁄4 (0.56)

3 (76)

18.5 (470)

141⁄2 (368) 173⁄8 (441)1616 1 (0.75) 19.0 (483)

11⁄2 (1.10) 21.0 (533)

2 (1.50) 23.0 (584)

1630

1635 2 (51)

1⁄2 (0.37)

31⁄2 (89)

18.0 (457)

131⁄2 (343) 161⁄8 (410)1632 3⁄4 (0.56) 18.5 (470)

1634 1 (0.75) 19.0 (483)

11⁄2 (1.10) 21.0 (533)

1636

1641 2 (51)

11⁄2 (1.10)

35⁄8 (92)

21.0 (533)

161⁄2 (419) 191⁄2 (495)1638 2 (1.50) 23.0 (584)

3 (2.37) 24.0 (610)

Comments: ____________ ____________________________

MOTORS1750 RPM, Three Phase 200V or 230/460V, 60Hz.Also available in Single Phase with overload protection except3HP (2238 Watts).

BODY Flanged in-line connections. Companion flanges are included.

FLANGES Flanges are tapped for gauges (1⁄4" NPT).

IMPELLER Closed, dynamically balanced

DRIVE COUPLING Non-Metallic, vibration dampening

FRAME Ball bearing type, permanently lubricated.REMOVABLE BEARING CARTRIDGE FITS ALL MODELS.

MECHANICAL SEAL Type 21 2 Piece Standard – 250°F (121°C) Operating Temperatureor Optional High Temperature – 300°F (149°C) Operating Temperature

WORKING PRESSURE 175 PSI (1207 kpa). In accordance with ANSI Standard B16.1.

SPECIFICATIONS

1600 SERIES STOCK UNIT QUICK SELECTION CURVES (1750 RPM)

Item Standard Optional

Casing Cast Iron Bronze

Impeller Cast Bronze N/A

Shaft Hardened Alloy Steel Stainless Steel 416

Shaft Sleeve Cupro-Nickel N/A

Bracket Cast Iron Cast Iron with StainlessSteel Face Plate

MATERIALS OF CONSTRUCTION

N/A - Not Available

1600 SERIES CUSTOM UNIT QUICK SELECTION CURVES (1750 RPM)

Do it Once. Do it Right.®TACO, INC., 1160 Cranston Street, Cranston, RI 02920 Telephone: (401) 942-8000 FAX: (401) 942-2360.TACO (Canada), Ltd., 8450 Lawson Road, Unit #3, Milton, Ontario L9T 0J8. Telephone: 905/564-9422. FAX: 905/564-9436.

Visit our web site at: http://www.taco-hvac.com

Printed in USA

Copyright 2013

TACO, Inc.

P-3 & P-4 PUMPS

SUBMITTALB-880.4A

JOB: Flynn Elementary HVAC Upgrade REPRESENTATIVE: McNevin Co

UNIT TAG: P-3&4 ORDER NO. DATE: 11/13/2015ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:

2AD-esSeries e-1510Centrifugal Pumps - Base Mounted

SPECIFICATIONSFLOW 90 (GPM) HEAD 40 (FT)

HP 2 RPM 1800

VOLTS 208-230/460

CYCLE 60 PHASE 3

ENCLOSURE ODP Nema Premium Efficient

APPROX. WEIGHT 200

SPECIALS

Note: Equipped with NEOPRENE coupling

MATERIALS OF CONSTRUCTION Stainless Steel Fitted

FEATURESi-ALERT™ Condition MonitorANSI/OSHA Coupling GuardCenter Drop Out Spacer CouplingFabricated Heavy Duty Baseplate

MAXIMUM WORKING PRESSURE175 psi (12 bar) W.P. w/ 125# ANSI flange drilling

TYPE OF SEALStandard Seal(Buna-Carbon/Silicon Carbide)-F Standard Seal w/ Flush Line(Buna-Carbon/Silicon Carbide)

FLANGES ARE 125# ANSI - STANDARD

Series e-1510 2AD-es Centrifugal Pump Submittal B-880.4A

FLANGE DIMENSIONS IN INCHES (MM)SIZE THICKNESS O.D.

Discharge 2" 5/8" (16) 6" (152)Suction 2-1/2" 11/16" (17) 7-1/8" (181)

DIMENSIONS − Inches (mm) STANDARD SEALMOTOR FRAME

HA HB HC MAX HD 2HE HF1 HF2 HH HL HM MAX HO HP Y Z "es" FRAME

56 12(305)

28-3/4(730)

28-7/8(733)

9-3/4(248)

10-1/4(260)

22-1/2(572) − 3/4

(19)3-9/16(90)

13-3/8(340)

16-1/4(413)

3(76)

3-1/2(89)

4-3/4(121)

143T 12(305)

28-3/4(730)

29(737)

9-3/4(248)

10-1/4(260)

22-1/2(572) − 3/4

(19)3-9/16(90)

13-1/2(343)

16-1/4(413)

3(76)

3-1/2(89)

4-3/4(121)

145T12

(305)28-3/4(730)

30(762)

9-3/4(248)

10-1/4(260)

22-1/2(572) − 3/4

(19)3-9/16(90)

13-1/2(343)

16-1/4(413)

3(76)

3-1/2(89)

4-3/4(121)

182T 14-5/8(371)

31(787)

32-5/8(829)

9-3/4(248)

12-7/8(327)

25(635) − 3/4

(19)2-3/16(56)

15(381)

16-1/4(413)

3(76)

3-1/2(89)

4-3/4(121)

184T 14-5/8(371)

31(787)

33-3/8(848)

9-3/4(248)

12-7/8(327)

25(635) − 3/4

(19)2-3/16(56)

15(381)

16-1/4(413)

3(76)

3-1/2(89)

4-3/4(121)

213T 14-5/8(371)

34-5/8(879)

36(914)

9-3/4(248)

12-7/8(327)

28-5/8(727) − 3/4

(19)2-3/16(56)

15-5/8(397)

16-1/4(413)

3(76)

3-1/2(89)

4-3/4(121)

215T 14-5/8(371)

34-5/8(879)

37-1/2(953)

9-3/4(248)

12-7/8(327)

28-5/8(727) − 3/4

(19)2-3/16(56)

15-5/8(397)

16-1/4(413)

3(76)

3-1/2(89)

4-3/4(121)

Dimensions are subject to change. Not to be used for construction purposes unless certified.

Xylem Inc.8200 N. Austin AvenueMorton Grove, IL 60053Phone: (847)966-3700 Fax: (847)965-8379www.bellgossett.comBell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries.ESP-REP v2015.03 © 2013 Xylem Inc.

P-5 PUMP

SUBMITTALA-126F

JOB: Flynn Elementary HVAC Upgrade REPRESENTATIVE: McNevin Co

UNIT TAG: ORDER NO. DATE: 11/13/2015ENGINEER: SUBMITTED BY: DATE: CONTRACTOR: APPROVED BY: DATE:

System LubricatedIron Body Circulators

DESCRIPTIONA flanged in-line system lubricated circulating pump designed specifically for quiet operation in a closed hydronic heating system.

OPERATING DATAMaximum Working Pressure: 150 psi (10.3Bar)Minimum Operating Temperature: 40°F (5°C)Maximum Operating Temperature NRF-22 & NRF-9F/LW: 240°F (115°C)

NRF-25, NRF-33, NRF-36 & NRF-45: 225°F (107°C)

CONSTRUCTION MATERIALSPump Body: Cast IronImpeller: NorylShaft: CeramicBearings: Carbon

SCHEDULE

MODELNUMBER

PARTNUMBER

STANDARD 60 CYCLE SINGLE PHASEMOTOR CHARACTERISTICS

TAGGING INFORMATION QUANTITYWATTS VOLTAGEF.L.

AMPS RPMNRF-9F/LW 103267 41 115 .40 2800

NRF-22 103251 92 115 .80 2940 P-5 1

NRF-25* 103417 125 115 1.1 2950NRF-33 103350 125 115 1.1 2950NRF-36* 103400 270 115 2.1 3300

NRF-45* 103404 270 115 2.1 3300*Three-speed pump

INHIBITED PROPYLENE GLYCOL

Technical Bulletin

JEFFCOOL® P-150 INDUSTRIAL COOLANT AND HEAT TRANSFER FLUID

GENERIC NAMES Inhibited propylene glycol

DESCRIPTION An inhibited propylene glycol based industrial coolant and heat transfer fluid.

APPLICATIONS Since JEFFCOOL P-150 coolant is formulated with propylene glycol, it is especially suitable for applications in which toxicological and environmental considerations are critical. JEFFCOOL P-150 is a heat transfer fluid for line heaters, for snow melting systems on loading ramps, highways, and runways; a coolant for ice rinks and air conditioning (HVAC) systems.

SALES SPECIFICATIONS

Specifications Slightly hazy and free of suspended matter

Property Appearance Freezing point,

Test Method* ST-61 ASTM D-3321

50 vol % solution, °C -32 max. 50 vol % solution, °F -25 max. pH, solution, 33% 9.5 min. – 10.5 max. ASTM D-1287 Reserve Alkalinity, mL 10.5 min. – 14.0 max. ASTM D-1121 Specific Gravity, 60/60°F 1.05 min. – 1.06 max. ASTM D-1122 Water, wt% 4.0 max. ASTM D-1123

*Methods of Test are available from Huntsman Corporation upon request.

ADDITIONAL INFORMATION

Regulatory Information DOT/TDG Classification Not regulated

HMIS Code 0-1-0 WHMIS Classification Not regulated

Chemical Control Laws Australia, AICS Listed Canada, DSL Listed Europe, EINECS/ELINCS Listed Japan, METI Not determined United States, TSCA Listed

Typical Physical Properties Boiling point, °C (°F) 187 (368)Density, lb/gal, 60°F 8.8 Flash point, PMCC, °C (°F) 100 (212) Melting/Freezing point, °C (°F) < -60 (< -76) Specific gravity 1 Odor Slight odorpH 9.9Vapor pressure, mmHg, 20°C (68°F) <1Viscosity, cSt, 40°C (104°F) < 20Water solubility (%) > 10

PRODUCT SAFETY POLICY It is the product safety policy of Huntsman Corporation to provide our customers with information on the safe handling and use of our products. The Material Safety Data Sheet (MSDS) should always be read and understood thoroughly before handling the product, and adequate safety procedures should be followed. Information on the toxicity, environmental and industrial hygiene aspects of our products may be found in the MSDS.

TOXICITY AND SAFETY For additional information on the toxicity and safe handling of this product, consult the Material Safety Data Sheet (Safety Data Sheet in Europe) prior to use of this product.

HANDLING AND STORAGE JEFFCOOL® P-150 coolant may be stored in unlined carbon steel tanks and drums. If storage of concentrated JEFFCOOL P-150 coolant for periods over 12 months is desired, it is recommended that the storage vessels be constructed from aluminum, stainless steel, or lined carbon steel. Vinyl, epoxy, and phenolic linings are suitable.

The normal precautions associated with any chemical should be observed in handling JEFFCOOL P-150 coolant. This product is neither explosive nor flammable under normal storage conditions. The propylene glycol in this product is considered practically nontoxic. Splashes onto eyes or skin, however, must be washed away quickly and medical treatment is advised for eye exposure. Breathing of the vapors or mists should be avoided.

AVAILABILITY JEFFCOOL P-150 coolant is available in tank wagons and 55-gallon, non-returnable steel drums. Bulk and drum inventory is available at select locations throughout the United States. Contact your local Huntsman Sales Representative for details. Samples are available by contacting our sample department at 1-800-662-0924.

Huntsman Corporation Business Offices 10003 Woodloch Forest Dr. The Woodlands, TX 77380 (281) 719-6000

Huntsman Advanced Technology Center Technical Service 8600 Gosling Rd. The Woodlands, TX 77381 (281) 719-7780

Samples 1-800-662-0924

www.huntsman.com

5112-0112

Copyright © 2007, 2012 Huntsman Corporation or an affiliate thereof. All rights reserved. JEFFCOOL® is a registered trademark of Huntsman Corporation or an affiliate thereof in one or more, but not all countries.

Huntsman Corporation warrants only that its products meet the specifications stated herein. Typical properties, where stated, are to be consideredas representative of current production and should not be treated as specifications. While all the information presented in this document is believed to be reliable and to represent the best available data on these products, HUNTSMAN MAKES NO WARRANTY OR GUARANTEE OFANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF ANY THIRD PARTY, OR WARRANTIESAS TO QUALITY OR CORRESPONDENCE WITH PRIOR DESCRIPTION OR SAMPLE, AND ANY USER OF PRODUCTS DESCRIBEDHEREIN SHOULD CONDUCT A SUFFICIENT INVESTIGATION TO ESTABLISH THE SUITABILITY OF ANY PRODUCT FOR ITS INTENDED USE AND ASSUMES ALL RISK AND LIABILITY WHATSOEVER RESULTING FROM THE USE OF SUCH PRODUCT, WHETHER USEDSINGLY OR IN COMBINATION WITH OTHER SUBSTANCES. Product(s) described in this publication may be hazardous and/or toxic and require special precautions in handling. For all product(s) described herein, the user should obtain from Huntsman detailed information on hazardsand/or toxicity, together with proper shipping, handling, and storage procedures, and should comply with all applicable safety and environmental standards. The behavior, hazards and/or toxicity of the product(s) referred to in this publication in manufacturing processes and their suitability inany given end-use environment are dependent upon various conditions such as chemical compatibility, temperature, and other variables, whichmay not be known to Huntsman. It is the sole responsibility of the user of such product(s) to evaluate the manufacturing circumstances and thefinal product(s) under actual end-use requirements and to adequately advise and warn future purchasers and users thereof.

GF-1 GLYCOL FEEDER

Data $fteef

ApplicationOur g lycol feeders mainta in a consis tentpressure in closed loop systems automaticallyal lowing for expansion and contraction ofglycol at rcA%.

The feeder is construcled on a rugged paintedsteel frame with a polyethylene tank, highflow feed purnp, prewired controller, low levelcut-off alarm and preplumbed piping assemblywith pressure gauge, pressure sensor, backcheck and relief valve,

Dig i ta l models d ig i ta l ly d isp lay the actualpressure of the loop and have a user settablecontrol pointfor pump activation and pressurerelief makrng start-up and operation easy.

wc-370302wc-370392-DwcD-3703A2wcD-370302-DGlycol Feeder

For ClosedLoop Sysferns

Key Features. Digital Displayed Pressure

' Simple $et Point Control

. lndustrial Steel Frame

, Audible Alarm

' Prewired Controls

. Low Level Pump Cut off

' Dual Systems

. Copper Pip ing

wcD-370302

#tu

Models$tanciari unrt: Copgi*r Pli:, 'nbing. analog cnntrol,55 gai lank, sie*i frame, 1d-i6 psi swiich, 1.3 *pnrpump, lov!/ level cut-aif anci audible alarm withsiience switch, dry contaci alarrn, pr*ssure relielvaive and PVC plumbing assembiy with presnuregauge.

Dig i ta l models have a contro i uni t tha i d ig i ia l lydispiays the actual ioop pressure and allow for usersettable contrsl pcints. The plumbing asseinblycomes compiete with a presslire sensof rated for5-100 psi {0.3-6.9 bar} applications.An exampie msdel number WCD-370302

Analog models have a cnntrol unit wtth analogswitches for testing and LED indicaior l ights" Theplumbrng assembly conts$ complete with a 30-60psj (2 04 1 bar) pressur* switclr.

WC-370302 Standard Uni lWC-37030?D Dual Unit, {or iwo separate loopsWCD-370302 Single Digiiai UnilWCD-370302D Digital and Dual, fsr two

separate loopes

Opt ions

30 30 gal (1 '1 3 l i ier ) tark rn p lece of 55 ga '100 100 gal . (378 l i ter ) tank in p lace of 55 gal .Al ternate purnp s ize" 3 3 gpm / 6C psi

Specif icat ionsElectrical

" Inpul. Alarm

. Motor

Plumbing. Standard

'120 VAC, 5C160 i-.t:Dry Cantact5 Amp {resistive), SPST

113 HP Pump: 1.3 GPhl

Copper

LE'EL \>-caxTnoule ,1,//

r;.-;--*.:-=")l c c $ i i ? iia_:_--_:__:-'

Digiial Controller Analog Controller

Fositive Displacement Pump. Pump ra ted a t 1 .3 GPM = 100 psr (s tandard) < -. Pump rated at 3 3 GPM = 6C psi

EnclosureHeavy Duty NEMA 4X style hiEh irnpactthermoplastic wlth padlockable gasketed Lexanviewing door

Pressure Gauge 0-100 psi

G lyco lTankL J d F i d U l t y

Tank and L id

Dimensions

/S lpnoard 55 na l ra rk

stand & single prmpli

Vd:S.5" (74.93 crn)H 5'3' l '160.02 cmJD 29.5 ' {74 .93 cm)

Shipping WeightwcD-370302wcD-370302D

5 5 n a l l n n c

Polyethylene

140 lbs {63 50 kg) approx165lbs i74.84 kg) approx

i . 3 t- * l* * l

t g L ! r

1-.;*M E{ : Bc e l0 i g| l 0

si20 ''10

PRE-STARTUP CLEANER

PreClean-6032

PreClean-6032 Boiler/Cooling System Cleanser

Product Description • PreClean-6032 is a blend of organic surface reduction and dispersal agents for cleaning

applications of industrial water systems.• PreClean-6032 was designed to clean fouled surfaces of heat transfer equipment, to cleanse

the system of dirt, debris, oil, mill scales and general grime.• PreClean-6032 is especially effective in both cleaning and scrubbing these dirt like deposits

and at the same time providing a passivated corrosion inhibitory film on the cleansed metalsurface.

• PreClean-6032 can be used for boiler, closed loop or cooling systems.• PreClean-6032 should be applied as a pre-treatment cleaner and is not intended as an on-line

treatment.• PreClean-6032 functions by penetrating the matrix of organic deposits, chelation of metallic

ion deposits, dispersal of particulate matter and reducing the surface tension of the dirt/oil filmas well as surface scrubbing agent action which clean away the dirt.

• PreClean-6032’s cleansing action allows the surface areas to be free of dirt, oil and millscales, which then allows the temporary corrosion inhibitory films of PreClean-6032 to adhereuntil a longer term treatment regimen is applied.

Application Rate and Control Parameters • PreClean-6032, the amount used will depend upon the severity of the dirt, grime, oil and mill

scale left in the equipment. For maintenance of clean surfaces in previously cleaned systemswhere PreClean-6032 is being applied occasionally as preventive maintenance.

• PreClean-6032 should be fed at a rate of 120-360 ppm. For systems where a greatercleansing action is required PreClean-6032 should be fed at a rate of 1200-10,000 ppm.

• PreClean-6032 should be pre-mixed in a volume of water and then applied to the system. Forboiler or hot water closed loops increasing the temperature of the re-circulating water willassist PreClean-6032 in its cleansing action.

• PreClean-6032 utilized for cooling or chill loops should be applied at ambient temperature andre-circulate the system for a longer period of time. Generally a 4-12 hour recirculation rate isneeded for any effective cleaning process.

• PreClean-6032 applied to heavily fouled systems may tend to slough large amounts ofdeposited material; therefore, adequate precautions should be taken to prevent plugging ofscreens, small lines and heat exchangers.

Physical Properties: PreClean-6032 System Boiler/Cooling Cleanser Form: Liquid Color: Light AmberOdor: Slight Aromatic pH: 12+/-Density: 9.09#/gallon Specific Gravity: 1.09Freeze Point: Approximately 32F Freeze/Thaw Recovery: Complete Ship Class: Non Regulated Materials HMIS Code 100C Refer to the MSDS for further health, safety and environmental information regarding this product. Information and recommendations in this bulletin are based on information believed to be reliable. However, the use of the product is beyond the control of MCI, and no guarantee, expressed or implied, is made as to the effects of such the results to be obtained if not used in accordance with directions or established safe practice. The buyer must assume all responsibility, including injury or damage, resulting from misuse of the product as such, or in combination with other material

BYPASS CHEMICAL POT FEEDER

Specification SheetFLAT BOTTOM BYPASS FEEDERS

MANUFACTURING: Mixers, Bypass Feeders, Filter Feeders, Bromine Feeders, Sample Coolers, Sludge Traps, Separators, Separator Systems, Tank Stands, Tank Package Systems, Glycol Feed Systems, Coupon Racks, Control Stations, NEMA Enclosures, Custom Packaged Systems and Specialty Welding

P.O. Box 6207 l Garden Grove, CA 92846-6207 / 11800 Monarch St. l Garden Grove, CA 92841-2113 l Phone (714) 379-5519 l Fax (714) 379-5549Northern California Region l Phone (510) 487-5310 l Southwest Region l Phone (602) 470-1015 l Email: customerservice@jlwingert.com

www.jlwingert.com

Note: All dimensions are +/- 1/8". All weights are approximate. All dimensions are subject to change without notice.

SS030001.A 10/12

DIMENSIONS, WEIGHT & CUBE:

KEY 2HD 5HD 12HD 18HD

A 21 1/8" 21 1/8" 41 3/4" 60 5/8"

B 12 1/2" 10 5/8" 31" 44"

C 3 1/4" 4 1/4" 4 1/8" 8 1/2"

D 6" 10" 10" 10"

WEIGHT 19 lbs. (8.6 kgs.) approx. 33 lbs. (15 kgs.) approx. 58 lbs. (26.3 kgs.) approx. 82 lbs.(32.7 kgs.) approx.

CUBE 6" x 6" x 22" 10" x 10" x 22" 10" x 10" x 44" 10" x 10" x 63"

PARTS, MATERIALS AND SPECIFICATIONS

KEY PART SPECIFICATIONS

1 3071 CLOSURE: 3 1/2" cast iron, 1/4 turn closure, (O-ring included)

2 3072 O-RING: Buna-N O-ring 200°F

3 BODY: Carbon steel

4 INLET: 3/4" FNPT

5 OUTLET: 3/4" FNPT

MAX. PRESSURE 200 PSI (13.6 BAR)

MAX. TEMPERATURE 200°F (93°C)

VOLUME (FILL CAPACITY)

MODEL GALLONS LITERS

2HD 2.16 8.17

5HD 5.79 21.92

12HD 12.76 48.30

18HD 19.22 72.75