PRODUCT DATASHEET Strada-SQ series

PRODUCT DATASHEETStrada-SQ serieslast update 15/11/2013

Ordering number

FamilyTypeLEDColorDiameterHeightStyleOptic MaterialHolder MaterialFasteningStatus

CA13509_STRADA-SQ-T2

Strada-SQAssemblyLUXEON MBlack25 x 25 mm8.7 mmSquare PMMA - - Ready

FWHMEfficiencycd/lmGerber File

Asymmetric degrees 93 % 0.600 Available

We recommend a minimum center to center spacing between STRADA-SQ-T2 lenses of 30mm (edge to edge spacing >5mm) to ensure the best optical performance.

Ordering number


CA13688_STRADA-SQ-T3

Strada-SQAssemblyLUXEON MClear25 x 25 mm8.4 mmSquare PMMA - - Ready



We recommend a minimum center to center spacing between STRADA-SQ-T3 lenses of 30mm (edge to edge spacing >5mm) to ensure the best optical performance.

Ordering number


CA13758_STRADA-SQ-FS-NP

Strada-SQAssemblyLUXEON MClear25x25 mm12.6 mmSquare PMMA - - Ready


Asym degrees 92 % 0.900 Available

Ordering number


CA13897_STRADA-SQ-FS

Strada-SQLensLUXEON MClear25x25 mm12.6 mmSquare PMMA - - Ready



December 5th 2013 17:03 Copyright Ledil Oy - Subject to change without prior notice - /4

Ledil Oy Salorankatu 10 24240 SALOFinland

http://www.ledil.com email: [email protected] FAX: +358-2-733 8001


Ordering number


C13866_STRADA-SQ-CY

Strada-SQLensLUXEON MClear25x25 mm10.1 mmSquare PMMA - - Ready


120+115 degrees 94 % 0.410 Available

Ordering number


CA14219_STRADA-SQ-CY

Strada-SQAssemblyLUXEON MClear25x25 mm10.1 mmSquare PMMA - - Ready


120+115 degrees 94 % 0.410 Available

Ordering number


C12727_STRADA-SQ-VSM

Strada-SQLensLUXEON MClear25 x 25 mm6.8 mmSquare PMMA - Screw, pin, glue Ready


154 degrees 93 % 0.250 Available

Ordering number


CA12891_STRADA-SQ-VSM

Strada-SQAssemblyLUXEON MClear25 x 25 mm6.95 mmSquare PMMA - Screw, pin, tape Ready


154 degrees 93 % 0.250 Available





NOTE: The typical divergence will be changed by different color, chip size and chip positiontolerance. The typical total divergence is the full angle measured where the luminous intensityis half of the peak value.





GENERAL INFORMATION

- Product series especially designed & optimized for LUXEON M series of LEDs. - Special care taken to make light distribution as uniform as possible.- Lens material optical grade PMMA with high UV and temperature resistance (105 degrees of Celcius / 220degrees of Fahrenheit). Allows use of high current and temperature conditions.

Please find more information about used material from below:http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20UL94_Yellow%20Card.pdfhttp://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20PLEXIGLAS-Datasheet.pdf

- Fastening to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details byclicking link: http://www.ledil.com/datasheets/DataSheet_TAPE.pdf

- Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glueoptions.http://www.ledil.com/datasheets/DataSheet_GLUES.pdf

NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the endproduct. For example, mechanical stress, vibration and holes on the surface of the circuit boarweaken the strength of the tape.

NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant andbalanced with fastening surface. Slanted assembly might cause unbalanced bond to thesurface. All surfaces where tape is applied must be clean, dry and free from grease and dirt.

If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of yourLED manufacturer - this is important as cleaning shall under no circumstances damage LEDs orother electronics components on the PCB.

Further note that optical components shall not be cleaned with any chemicals - only micro fibercloth may be used to remove fingerprints or other traces from handling.NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the endproduct. For example, mechanical stress, vibration and holes on the surface of the circuit boarweaken the strength of the glue.

NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. Ifcleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LEDmanufacturer -this is important as cleaning shall under no circumstances damage LEDs or otherelectronics components on the PCB.

Further note that optical components shall not be cleaned with any chemicals - only micro fibercloth may be used to remove fingerprints or other traces from handling.




Tape

Beam direction

AD

BC AD

33

22

44

11

Tolerances if not otherwise shownAccording to DIN ISO 2768-1Linear measures:Up to 30mm class F, otherwise class M.According to DIN ISO 2768-2Form and position: class K

SCALE 3:2 WEIGHT - SHEET 1/1

SIZE

A4

DRAWING TITLE

STRADA-SQ-T2 DatasheetPART NUMBER

-

Ledil OySalorankatu 10FIN 24240 SALOFinland

THIRD ANGLE PROJECTION:

This drawing is the propertyof LEDiL Oy. It may not bereproduced, copied orcommunicated without a writtenagreement with LEDiL Oy."

8.6

2Front view

A

25.4

c/c

21.5

c/c

3.2

2

Bottom view

2525

Top view

Isometric view

0.15

Detail A

Minimum spacing

30

c/c

5

PRODUCT DATASHEET Strada-SQ series

Documents

Transcript of PRODUCT DATASHEET Strada-SQ series