Procedure Editor. 2 16.11.2015 16:17 This SOP describes the Setting procedure and order folders. How...
-
Upload
chrystal-waters -
Category
Documents
-
view
214 -
download
1
Transcript of Procedure Editor. 2 16.11.2015 16:17 This SOP describes the Setting procedure and order folders. How...
Procedure Editor
Procedure Editor
2 20.04.23 18:04
This SOP describes the
• Setting procedure and order folders.
• How to load procedures in order files for sources and destinations.
• The definition of dilutor solvents used.
• The differences between “Bruker” and “Custom” procedures.
• How to add and edit procedures and sub-procedures.
Introduction
Procedure Editor
3 20.04.23 18:04
This button is used to change the procedure export directory path.
Check the correct procedure export path. The directory contains all procedures for the “Create order dialog“ window.
Edit Settings
Procedure Editor
4 20.04.23 18:04
Open the procedure editor dialog
The procedures can be defined here and will be used later to set up orders within the following applications:
• PrepGilsonST “Create order dialog“ • SampleTrack
Procedure Editor Dialogue
Procedure Editor
5 20.04.23 18:04
Procedures defined and saved here…
… can be selected later in the “Create order dialog“.
1a. Using Procedure in Order files
Procedure Editor
6 20.04.23 18:04
Placeholder variables for SOURCE Samples defined here…
… can be selected later when setting up orders in the “Create order dialog“ .
1b. Using Procedure in Order files: Source
Procedure Editor
7 20.04.23 18:04
Dispenses defined here…(the DESTINATION position variable in the Order file will be used!)
… can be selected later when setting up orders in the “Create order dialog“.
1c. Using Procedure in Order files: Destination
Procedure Editor
8 20.04.23 18:04
Placeholder variable for a Dilutor/ValveMate solvent defined here…(selection „##$SOLVENT Variable in Order “)
… can be selected later in the “Create order dialog“.
1d. Using Procedure in Order files: Dilutor Solvent
Procedure Editor
9 20.04.23 18:04
Procedures of the type “Bruker“ cannot be saved. The “Save“ button is gray.
Save the procedure with the button “Save As“ and use a different personalised name like “my procedure“.
Open the “Saved as“ procedure. It has the custom symbol and can be modified and saved.
2. Procedure Difference: “Bruker“ / “Custom“
Procedure Editor
10 20.04.23 18:04
After opening the new procedure it will be displayed as a “Custom“ procedure.
2a. View a “Custom“ Procedure
Procedure Editor
11 20.04.23 18:04
Use this button to load procedures (only for procedures of type “ADD“)
2b. Open Procedure
Procedure Editor
12 20.04.23 18:04
Click on the “Source Type“ of any line to select it and show all values in the line edit area.
3. Show Procedure Values
Procedure Editor
13 20.04.23 18:04
2. Press the button “Update“ to set the new values in the selected line.
1. Enter the parameters for the solvent at the Dilutor / ValveMate.
4a. Edit the Source Type “Solvent at Dilutor“
Procedure Editor
14 20.04.23 18:04
4a. Edit the Source Type “Solvent at Dilutor“
Select the solvent name from the list.
Tip: For each solvent name in the list the position on the ValveMate is predefined in the configuration.
Procedure Editor
15 20.04.23 18:04
2. Press the “Update“ button to set the new values in the selected line.
1. Enter the gas gap parameters.
4b. Edit the Source Type „Gas Gap“
Procedure Editor
16 20.04.23 18:04
2. Press the “Update“ button to set the new values in the selected line.
1. Enter the sample parameters
( = Source in the order file).
4c. Edit the Source Type “Sample“
Procedure Editor
17 20.04.23 18:04
2. Press the “Update“ button to set the new values in the selected line.
1. Enter the parameters for the tray solvent.
4d. Edit the Source Type “Solvent in Tray“
Procedure Editor
18 20.04.23 18:04
Select the solvent name from the list.
Tip: For each solvent name in the list the position in the tray is predefined in the configuration.
4d. Edit the Source Type “Solvent in Tray“
Procedure Editor
19 20.04.23 18:04
1. Check the type of subprocedure.
2. Select the name of the subprocedure (all files of subdirectory ...\Disp\ are listed ).
5. Adding Subprocedures to a Line
Procedure Editor
20 20.04.23 18:04
A procedure with the type “Dispense“ will be opened.
5a. Editing a Subprocedure Type “Disp“
Procedure Editor
21 20.04.23 18:04
A procedure with the type “Mix“ is opened.
5b. Editing a Subprocedure Type “Mix“
Procedure Editor
22 20.04.23 18:04
A procedure with the type “Clean“ is opened(Save as a Custom procedure to edit).
5c. Editing a Subprocedure Type “Clean“
Procedure Editor
23 20.04.23 18:04
1. Select a line from the list.
2. Modify the values as required.
3. Use the “Add below“ button to insert a copy of the current line.
6. Adding Lines
Procedure Editor
24 20.04.23 18:04
5. Press the “Paste below“ button.
1. Select a source line from the list.
2. Modify the values as required.
3. Use the “Copy“ button to copy the current value area.
4. Select a location to paste the new data.
7. Copying and Pasting Lines
Procedure Editor
25 20.04.23 18:04
Use the “Delete“ button to remove the selected line
from the list.
8. Deleting Lines
Procedure Editor
26 20.04.23 18:04