Presentation1
-
Upload
cameronmaclaughlin -
Category
Entertainment & Humor
-
view
108 -
download
0
description
Transcript of Presentation1
![Page 1: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/1.jpg)
BY: CAMERON MACLAUGHLIN
BUILDING A GUITAR
![Page 2: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/2.jpg)
The 4 main parts of the guitar
The body The neck
The headstock The fret board
![Page 3: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/3.jpg)
Tools
Band saw
Belt sander
Router
Fretting tools
Chisel set
Drill press
Clamps
![Page 4: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/4.jpg)
Materials
2”x16” hardwood board
2”x6” hardwood board template
Guitar hardwareWood glue Wood for the fret board
![Page 5: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/5.jpg)
First set of steps
The body
![Page 6: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/6.jpg)
Take the body board and trace the template on it.
![Page 7: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/7.jpg)
Use the band saw and cut the board around where you traced.
![Page 8: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/8.jpg)
Use the belt sander around the edges to sand off any cut marks.
![Page 9: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/9.jpg)
Trace the holes from the template on the front and back of the guitar.
![Page 10: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/10.jpg)
Use the router and cut the holes in the top and bottom of the guitar.
![Page 11: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/11.jpg)
Second set of steps
The neck
![Page 12: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/12.jpg)
Trace the guitar neck on the neck board.
![Page 13: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/13.jpg)
Cut it out with the band saw.
![Page 14: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/14.jpg)
Use the chisel set to round the back of the neck.
![Page 15: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/15.jpg)
Drill the holes for the tuning pegs.
![Page 16: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/16.jpg)
Third set of steps
The fret board
![Page 17: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/17.jpg)
Trace the template of the fret board on the wood for the fret board.
![Page 18: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/18.jpg)
Cut it out with the band saw.
![Page 19: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/19.jpg)
Clamp the fret board to the neck and wait until dried.
![Page 20: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/20.jpg)
Use the fretting tools to cut the slots for the frets. Then install the frets.
![Page 21: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/21.jpg)
Forth set of steps
Full Assembly
![Page 22: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/22.jpg)
Screw the neck into the body.
![Page 23: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/23.jpg)
Install all the body hardware and neck hardware.
![Page 24: Presentation1](https://reader036.fdocuments.us/reader036/viewer/2022070302/547c1f61b4af9fb2188b462b/html5/thumbnails/24.jpg)
The Outcome